22D Combo Rev1
Warranty Program/Extension
Emissions Recall 22D - On Board Diagnostics - Dealer Notification (Revision 1)
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
22D Combo Rev1
Emissions Recall 22D - On Board Diagnostics - Dealer Notification (Revision 1)
22D Combo
Emissions Recall 22D - On Board Diagnostics - Dealer Notification
112842
BOLT - HEX FLANGE HEAD
2623000037 REV.A
Condensation Or Water Infiltration In Headlights, Daytime Running Lights (DRL), Turn Signals, Fog Lights, Taillights. Rev A
S2623000037
Condensation Or Water Infiltration In Headlights, Daytime Running Lights (DRL), Turn Signals, Fog Lights, Taillights.
01-001-26
Oil Change Monitor Displaying Prematurely Customers may experience the following: ● The oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles) This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
64C Combo
Customer Satisfaction Notification 64C – Powertrain Control Module Wiring Harness- Dealer Notification
9100325 Rev 1
Before replacing any parts please refer to SOL S2518000008 if it applies to the vehicle you are working on based on a VIN search in Service Library. Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1705000002 REV.A
Front Brake Pulsation and/or Clunk Noise
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
9100469
VAPOR CANISTER If an issue is detected with the EVAPORATIVE SYSTEM INTEGRITY MODULE DETECTOR and not the VAPOR CANISTER, only replace the EVAPORATIVE SYSTEM INTEGRITY MODULE DETECTOR.
01-002-24
Oil Change Monitor Displaying Prematurely Customers may experience the following: ● The oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles). This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
S2308000089
The Replacement BCM Front Harness Is Not The Same As The Original
0816423
Humidity Sensor Harness Missing Technician may have issues re-establishing the connection after replacing the vehicle rear wiring. There is no humidity sensor connection on the vehicle rear wiring harness
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2308000004
Vehicle Cranks, No Start
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
0100122
Oil Change Monitor Displaying Prematurely This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter. The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).
S2218000018
Check engine lamp/Mil lamp-on. Engine misfires.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2008000078RevA
Start Stop Inoperative After A Recent Vehicle Service
S2223000047
ACC Does Not Operate. Start Stop Unavailable, ACC Unavailable Service Required Messages. C1452-86 Engine Torque DASM- Signal Invalid
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
01-001-21
Oil Change Monitor Displaying Prematurely This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter. The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).
0100121
Oil Change Monitor Displaying Prematurely This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter. The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).
9004335
Turbocharger If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately and complete turbo replacement may not be necessary.
S1708000262
(Rev. A) Check Engine Lamp Is On, Intermittent Module CAN Private Or LIN BUS Codes
S1708000262 Rev.
(Rev. A) Check Engine Lamp Is On, Intermittent Module CAN Private Or LIN BUS Codes
S2018000012
Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
S2018000011
Issue includes a fault code(s) set in the Powertrain Control Module (PCM) for P0299, P0300, P0301, P0302, P0303, and/or P0304 after performing the PCM software update process for Customer Satisfaction Notification (CSN) W05.
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
08-065-20
RAN RAP RAG and RSD 2.5 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio to software level to MV 090.000.061The customer should be informed that after the reprogram, the radio will need to have the phones paired to theEntertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the Owner Handbook of the infotainment module. Some customers may experience one or more of the following: Radio may reboot while driving.Software update will help correct existing issue. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.
0806520
RAN RAP RAG and RSD 2.5 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio to software level to MV 090.000.061The customer should be informed that after the reprogram, the radio will need to have the phones paired to theEntertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the Owner Handbook of the infotainment module. Some customers may experience one or more of the following: Radio may reboot while driving.Software update will help correct existing issue. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.
18-051-20
P00C0-00 Turbocharger-Supercharger Bypass Valve 2 Control Circuit This bulletin involves inspecting and if necessary replacing the connector for the left turbocharger bypass valve and installing a protective cover. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:P00C0-00 Turbocharger-Supercharger Bypass Valve 2 Control Circuit
1805120
P00C0-00 Turbocharger-Supercharger Bypass Valve 2 Control Circuit This bulletin involves inspecting and if necessary replacing the connector for the left turbocharger bypass valve and installing a protective cover. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:P00C0-00 Turbocharger-Supercharger Bypass Valve 2 Control Circuit
S2008000079
Cluster Engine Run Hours Resets To Zero While Driving
S2008000080
Intermittent Crank Not Start
S2008000078
Start Stop Inoperative After A Recent Vehicle Service
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
21-032-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the (TCM), with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P0002-00 - Fuel Volume Regulator "A" Control Circuit Performance. P026E-00 - Charge Air Cooler Coolant Pump Performance. P1066-00 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P26E4-00 - Starter Relay "B" Circuit. P2B61-00 - Engine Coolant Flow Control Valve Stuck Closed. P2BC1-00 - Lt Water Pump Smart Driver Module. U1008-00 - LIN 1 Bus.
S2018000004
Issue includes a fault code set in the powertrain control module (PCM ) for U04B1-00-Invalid Data Received From Battery Monitor Module after flashing PCM for Customer Satisfaction Notification (CSN) W05.
01-001-20
Oil Change Monitor Displaying Prematurely This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter. The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).
18-027-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM), also known as a PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P0106-00 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. P013A-00 - O2 Sensor Slow Response - Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response - Rich To Lean Bank 1 Sensor 1. P026E-00 - Charge Air Cooler Coolant Pump Performance. U1008-00 - LIN 1 BUS. P1CEA-00 - Boost Side EVAP Purge System Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. P0455-00 - Evaporative Emission System Leak Detected (Large Leak). P0087 - Fuel Rail Pressure Too Low - Bank 1. P2172 - Throttle Actuator Control System - Sudden High Air Flow Detected. P0171 - System Too Lean Bank 1. P0236 - Turbocharger/Supercharger Boost Pressure Sensor Performance. P0363 - Misfire Detected - Fueling Disabled. P250B - Engine Oil Level Sensor Circuit Performance. P0139 - O2 Sensor Circuit Slow Response Bank 1 Sensor 2. P0440 - Evaporative Emission System Incorrect Flow. P0441 - Evaporative Emission System Incorrect Purge Flow. P0002 - Fuel Quantity Regulator 1 Control Circuit Performance. P0244 - Turbocharger/Supercharger Wastegate Solenoid ?A? Range/Performance. P062A - Fuel Pump ?A? Control Circuit Range/Performance.
S2008000021
PCM ESS Inhibits List Show Driver Door Condition Inhibiting The S&S
W05
Customer Satisfaction Notification W05 Reprogram Powertrain Control Module
S2008000017
ESS Unavailable In Areas 5,250 Feet (1600 Meters) Above Sea Level
08-025-20
RAN RAP RAJ RAG and RSD Radio Software Enhancements This bulletin involves reprogramming the radio with software level MV-002.010.041.The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the Owner Handbook of the infotainmentmodule. Some customers may experience one or more of the following:Voice commands not recognized, especially in SiriusXM®. Can?t select certain character in navigation, character grayed out. Tweeter noise during audio streaming. Ipod Nano® not recognized. Voice recognition does not work when setting an address in Spanish. Navigation takes too long to recover after losing satellite signal. Certain Android® phones have reduced Bluetooth® functionality. Display is stuck on black screen. Display frozen on Alfa Romeo logo. Radio intermittently reboots. Oil level displayed on the ETM is incorrect. Auto-play does not maintain ?ON? status after the network goes to sleep. Park Assist Module (PAM) graphics stayed on screen even after dismissing via Rotary Pad. Loss of favorite contacts. Lane Departure menu option available in a vehicle without the lane departure warning option. Some technicians may experience an error when they attempt to update the User Guide. The radio may prompt an error, "The update file has expired and cannot be installed"Fig. 1.Update File Error PromptIn addition, the following improvements are included:Stability improvements, to help prevent the radios from rebooting and freezing. Preset management improvements, for better usability. Additional phone compatibility improvements on phones not tested in the past. Radio station preset bar updated to include seven presets and a shortcut to the rest of the presets. Radio menu updated to show frequency, station names, and favorite numbers. Remove kilohertz (KHz) and megahertz (MHz) and show frequency in figures.
S2008000013
Key Programming, Security Pin Request, Pin Invalid
18-097-19
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM), also known as a Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set: P013A-00 - O2 Sensor Slow Response - Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response - Rich To Lean Bank 1 Sensor 1. P026E-00 - Charge Air Cooler Coolant Pump Performance. U1008-00 - LIN 1 BUS. P1CEA-00 - Boost Side EVAP Purge System Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. P0455-00 - Evaporative Emission System Leak Detected (Large Leak). P0087 - Fuel Rail Pressure Too Low - Bank 1. P2172 - Throttle Actuator Control System - Sudden High Air Flow Detected. P0171 - System Too Lean Bank 1. P0236 - Turbocharger/Supercharger Boost Pressure Sensor Performance. P0363 - Misfire Detected - Fueling Disabled. P250B - Engine Oil Level Sensor Circuit Performance. P0139 - O2 Sensor Circuit Slow Response Bank 1 Sensor 2. P0440 - Evaporative Emission System Incorrect Flow. P0441 - Evaporative Emission System Incorrect Purge Flow. P0002 - Fuel Quantity Regulator 1 Control Circuit Performance. P0244 - Turbocharger/Supercharger Wastegate Solenoid ?A? Range/Performance. P062A - Fuel Pump ?A? Control Circuit Range/Performance. P0128 - Coolant Thermostat (Coolant Temperature Below T
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
08-081-19
RAN RAP RAG and RSD 2.5 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio to software level MV 085.000.046. The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the OwnerHandbook of the infotainment module. Some customers may experience one or more of the following:Radio may reboot while driving. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.
23-014-19
Excessive Delay in Passenger Side Power Mirror Unfolding/Opening This bulletin involves replacing the driver side mirror switch and passenger side window switch. Customers may experience the following:An excessive delay (up to 20 sec.) with the passenger power mirror not unfolding (opening) after starting the vehicle.
08-042-19
Flash: Anti-Lock Brake System (ABS) Module Diagnostic and System Updates This bulletin involves reprogramming the ABS module with the latest available software. The following enhancement is included with this update:Improved brake pedal feel.
9003293
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
D-17-21
Radio Pre-Authorization Program - Select 7.0/8.4/8.4N Radios (New and Exchange) - 2018 Model Year Vehicles
0802717REVB
Flash: Body Control Module (BCM) Diagnostic and System Improvements This bulletin involves reprogramming the BCM with the latest available software. Customers may experience one or more of the following:When ?Race Mode? is selected and during high-performance driving (i.e. track usage), the fuel gauge does not accurately report the actual fuel level as the tank approaches empty. The Forward Collision Warning (FCW) system may be disabled intermittently. The last bar on the fuel gauge will not turn off, even if the fuel tank is empty. If the battery state of charge drops below 75%, the rear defrost will turn off after 15 minutes.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.