1804823
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
Vehicle report
2015 ALFA ROMEO 4C
Service bulletins
61 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384
Service Bulletin/Repair Instructions
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
3100123
Service Bulletin/Repair Instructions
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31-002-22
Service Bulletin/Repair Instructions
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100122
Service Bulletin/Repair Instructions
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
Service Bulletin/Repair Instructions
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2108000163
Service Bulletin/Repair Instructions
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Service Bulletin/Repair Instructions
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004386
Service Bulletin/Repair Instructions
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1608000226
Service Bulletin/Repair Instructions
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Service Bulletin/Repair Instructions
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Service Bulletin/Repair Instructions
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Service Bulletin/Repair Instructions
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Service Bulletin/Repair Instructions
Customer complaint may include engine oil leak/consumption.
23-015-20
Service Bulletin/Repair Instructions
Disinfectant Solution Recommended for COVID-19
08-049-20
Service Bulletin/Repair Instructions
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Service Bulletin/Repair Instructions
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Service Bulletin/Repair Instructions
Hands On Steering Wheel Message In EVIC
9004022
Service Bulletin/Repair Instructions
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Service Bulletin/Repair Instructions
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Service Bulletin/Repair Instructions
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Service Bulletin/Repair Instructions
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Service Bulletin/Repair Instructions
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Service Bulletin/Repair Instructions
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
Service Bulletin/Repair Instructions
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003220
Service Bulletin/Repair Instructions
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003355
Service Bulletin/Repair Instructions
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
9003413
Service Bulletin/Repair Instructions
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Service Bulletin/Repair Instructions
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Service Bulletin/Repair Instructions
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003694
Service Bulletin/Repair Instructions
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Service Bulletin/Repair Instructions
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Service Bulletin/Repair Instructions
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
05152029
Service Bulletin/Repair Instructions
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68105583A
Service Bulletin/Repair Instructions
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
RL305553A
Service Bulletin/Repair Instructions
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
68141352A
Service Bulletin/Repair Instructions
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
02-003-16
Service Bulletin/Repair Instructions
Front End Knocking/Ticking Noise While Steering This bulletin involves installing additional rivets to the front stabilizer bar support brackets. The customer may describe a knocking/ticking type noise while steering. The noise may be caused by movement between the stabilizer bar bracket to the front frame.
Z5091195A
Service Bulletin/Repair Instructions
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
Service Bulletin/Repair Instructions
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Service Bulletin/Repair Instructions
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
0801416
Service Bulletin/Repair Instructions
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
RL108213A$
Service Bulletin/Repair Instructions
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
53034160A
Service Bulletin/Repair Instructions
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
21-058-15
Service Bulletin/Repair Instructions
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience the following: ? Whine coming from the transmission during gear change. ? Transmission lamp on the Instrument Panel Cluster (IPC) is illuminated. ? Harsh shifting during low speed driving. The following enhancements are included in this software update: ? Improved torque management during gear shifts. ? Better clutch thermal management to improve shift quality. ? Improved low speed driving behavior.
2105815
Service Bulletin/Repair Instructions
: Transmission Diagnostic And Shift Enhancements.
18-056-15
Service Bulletin/Repair Instructions
Clicking Noise From Auxiliary Water Pump Relay This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. A small number of customers may experience a clicking type noise coming from the engine area while driving. The concern may be caused by rapid activation and deactivation of the auxiliary water pump relay. This software update will improve the activation and deactivation cycle of the auxiliary water pump relay.
02-005-15 REVB
Service Bulletin/Repair Instructions
Front End Popping Noise While Driving Over Bumps This bulletin involves using structural adhesive to bond the front upper shock absorber brackets to the carbon fiber structure. The customer may describe a popping noise in the front of the vehicle while driving over bumps at low speeds. The popping noise may be caused by movement between the front upper shock absorber mount bracket and the carbon fiber structure in the area shown in (Fig. 1). Fig. 1 Noise From Contact Area Between Shock Absorber Bracket And Structure
02-005-15 REVA
Service Bulletin/Repair Instructions
Front End Popping Noise While Driving Over Bumps This bulletin involves using structural adhesive to bond the front upper shock absorber brackets to the carbon fiber structure. The customer may describe a popping noise in the front of the vehicle while driving over bumps at low speeds. The popping noise may be caused by movement between the front upper shock absorber mount bracket and the carbon fiber structure in the area shown in (Fig. 1). Fig. 1 Noise From Contact Area Between Shock Absorber Bracket And Structure
02-005-15
Service Bulletin/Repair Instructions
Front End Popping Noise While Driving Over Bumps This bulletin involves using structural adhesive to bond the front upper shock absorber brackets to the carbon fiber structure. The customer may describe a popping noise in the front of the vehicle while driving over bumps at low speeds. The popping noise may be caused by movement between the front upper shock absorber mount bracket and the carbon fiber structure in the area shown in (Fig. 1). Fig. 1 Noise From Contact Area Between Shock Absorber Bracket And Structure
08-021-15 REV. A
Service Bulletin/Repair Instructions
Flash: MIL Illumination And Transmission Over Temperature Message This bulletin involves updating the Body Control Module (BCM) software. The customer may notice a cluster message ?Transmission Over Temperature? that appears for a short time and the Malfunction Indicator Lamp (MIL) may turn on. The customer may also notice that the Dynamic Car Control System may default to Natural mode and not allow the customer to change modes. On further inspection, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? B1067-67 VDSM (Vehicle Dynamic System Module) C CAN Signal-Signal Incorrect After Event. ? B1009-64 Brake Switches-Signal Plausibility Failure. ? B1009-67 Brake Switches-Signal Incorrect After Event. ? B10AA-4A Check Configuration Failed-Incorrect Component Installed. ? U1703-86 IPC (Instrument Control Panel)-Signal Invalid. ? U1703-87 IPC (Instrument Control Panel)-Missing Message. ? U11BC-00 Lost Brake Switch Message.
08-021-15
Service Bulletin/Repair Instructions
Transmission Over Temperature Message This bulletin involves updating the Body Control Module (BCM) software. The customer may notice a cluster message ?Transmission Over Temperature? that appears for a short time and the Malfunction Indicator Lamp (MIL) may turn on. The customer may also notice that the Dynamic Car Control System may default to Natural mode and not allow the customer to change modes. On further inspection, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? B1067-67 VDSM (Vehicle Dynamic System Module) C CAN Signal-Signal Incorrect After Event. ? B1009-64 Brake Switches-Signal Plausibility Failure. ? B1009-67 Brake Switches-Signal Incorrect After Event. ? B10AA-4A Check Configuration Failed-Incorrect Component Installed. ? U1703-86 IPC (Instrument Control Panel)-Signal Invalid. ? U1703-87 IPC (Instrument Control Panel)-Missing Message. ? U11BC-00 Lost Brake Switch Message.
23-030-14
Service Bulletin/Repair Instructions
Cosmetic Carbon Fiber Repairs This bulletin involves removing light to moderate surface conditions on carbon fiber finishes revealing a swirl-free, durable, protected finish. Isolated light to moderate surface conditions (scratches, scuffs, staining, hard water spots, etc.) on carbon fiber.
04-001-14
Service Bulletin/Repair Instructions
Vehicle Hoisting Precautions And Procedure The 4C ground clearance from the body side skirt to level ground is 110 mm (3.5 inches). Most standard vehicle lift arms will not fit under the vehicle. In order to lift the vehicle and avoid vehicle damage, the vehicle must be lifted using wheel jack dollies prior to attempting to lift the vehicle using a standard lift.Use the recommended GOJAKS jack dolly (model 4500) or equivalent to lift the vehicle at all four tires, then roll the vehicle into place to begin the lifting procedure.Failure to follow the Vehicle Hoisting Procedure will result in vehicle body damage.
31-001-14
Service Bulletin/Repair Instructions
Carbon Fiber Monocoque Repairs
9002519
Service Bulletin/Repair Instructions
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
31-001-13
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.