Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SIL-3273
Service Bulletin/Repair Instructions
Altec has received notification from Parker Chelsea, the manufacturer, of an issue with some of their 281 and 890 Series PTOs. An unintended restriction in lubrication flow may produce elevated back pressure in cold-start scenarios, leading to partial engagement of the clutch. Once the vehicle reaches normal operating temperature, the clutch drag will abate. In extreme cases, repeated cold starts may result in clutch disk damage and failure to engage when activated.
SIL-3143
Service Bulletin/Repair Instructions
Altec has learned that a 12-volt Airtronics relay installed in the PDM could have been manufactured to an insufficient threshold on certain units built from December 2004 to October 2022. This can cause the relay to overheat and fail, causing the accessory lights to stop working.
SIL 3129
Service Bulletin/Repair Instructions
Altec has learned that the cap screws used to mount the planetary winch at the turntable could be shorter than specified on certain D3000A/B and D4000A/B units built from January 2012 to December 2015.
SIL 3068
Service Bulletin/Repair Instructions
Altec has learned that certain digger derricks and aerial devices of various models built from January 2010 to January 2023 may contain access steps with a handrail and side plate that come together in a small space causing a potential pinch point. Altec has created a kit to eliminate the possible pinch point.
SIL-3052
Service Bulletin/Repair Instructions
Altec has learned that the hydraulic ball valve on the hydraulic reservoir return line of certain L42/45 M/P units built from February 2002 to November 2019 might not get returned to the open position after being turned to the closed position for maintenance. If the upper boom drive system is articulated while the ball valve is in the closed position, both upper boom drive cylinders could retract simultaneously causing the lower boom to buckle. The customer should order and install the Hydraulic Shutoff Valve Placard Kit. The kit must be installed by the next preventative maintenance interval, or within 90 days of receipt of this notice, whichever comes first.
SIL 3033
Service Bulletin/Repair Instructions
Altec has learned that on certain AT37-G aerial devices built from November 2007 to April 2018, the rear torsion bar swing arm can interfere with the long runner channels under the body as the torsion bar rotates during road travel. The interference can cause wear issues and can cause welds on the body mounting angles or cross members to develop cracks.
PA713
Service Bulletin/Repair Instructions
Product advisory posted on our web site to inform owners, user, & operators that the new ANSI A92.2-2021 standard has taken effect and they must review. The standard has changed some of the responsibilities of the parties who use or operate vehicle mounted aerial devices.
CSR-3012
Service Bulletin/Repair Instructions
Altec Industries, Inc. has received notification from Ford Motor Company that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with Altec equipment. In certain 2011 through 2013 and 2015 model year F-650 and F-750 vehicles with 70% fixed front seat built from February 14, 2011, to April 28, 2015, the front passenger and center seat belts might not be anchored in the correct position relative to the seat, increasing the risk of injury in a crash.
SIL 850
Service Bulletin/Repair Instructions
The body compartment wiring on certain Altec aerial devices, digger derricks, and body-only units built from 2014 to 2021 contains an in-line fuse located close to the lighting in the compartment, while other units are fused upstream, closer to the power source. Altec has learned that the units affected should have an in-line fuse close to the lighting, but this fuse was not installed on some units. In addition, some units may have exposed terminals at the end of certain portions of the wiring in the body. If the exposed terminals contact each other or with ground, the resulting direct short could damage the body compartment lighting. Inspect the body compartment lighting circuit at the unit's next scheduled service interval or within six months of receiving the SIL, whichever comes first. Use the Inspection Procedure or contact Altec to perform the inspection. This inspection and repair are covered under the Altec Warranty Policy and can be performed by Altec, the customer, or the customer's warranty provider. Altec will perform the work for free at an Altec facility. If the customer or the customer's warranty provider performs the work, a warranty claim must be submitted to be reimbursed for the cost of the parts and/or labor.
SIL 852
Service Bulletin/Repair Instructions
Altec has learned that the electrohydraulic outrigger/tools control valve on AA755L and A-series aerial devices and DLB, DMB, and D2/3/4000B series digger derricks could have the potential to produce a very small amount of flow into the lower tools circuit when the outriggers and tools mode is engaged. This can cause slow unintended movement of a tool such as a pole puller cylinder that is connected to the tool circuit. A blanking plug must be installed to prevent this issue. Inspect the outrigger/tools control valve using the Inspection Procedure. The inspection and repair are covered under the Altec Warranty Policy and can be performed by Altec, the customer, or the customer's warranty provider. Altec will perform the work for free at an Altec facility.
CSR 532
Service Bulletin/Repair Instructions
Altec Industries, Inc. has received notification from Navistar that a condition exists relating to motor vehicle safety, compliance, or emissions in a vehicle you possess that is equipped with Altec equipment. On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse position and the stationary PTO switch is engaged, the engine RPM will ramp up and may overcome parking brake hold capability resulting in possible vehicle movement. Unexpected movement of the truck from the park position can increase the risk of property damage or personal injury.
CSR 521
Service Bulletin/Repair Instructions
Fiat Chrysler Automobiles (FCA) US has decided that a defect that relates to motor vehicle safety exists on certain 2012 through 2020 model year (D2) Ram 3500 pickup, (DD) Ram 3500 cab chassis, and (DP) Ram 4500/5500 cab chassis vehicles. Refer to the included communication from FCA US for additional information. A remedy for this condition is not currently available. An additional notice will be mailed to you when a remedy is available. Altec is not able to complete this repair. This repair is not covered under the Altec Warranty policy.
SIL 782
Service Bulletin/Repair Instructions
There may be inadequate weld fusion between the boom extension cylinder rod and rod end on the affected units. This can lead to failure of the weld. Altec has developed a process to have the cylinder rod end attachment repaired by the cylinder manufacturer. Altec requires the repair be completed on the affected units by the next annual preventive maintenance interval or within one year of receipt of the SIL.
SIL 783
Service Bulletin/Repair Instructions
Structural cracking has been observed where the primary leveling cylinder mounting pin is welded to the lower boom side plate on LS 40/45/55 aerial devices. Failure of this connection could disable the hydraulic platform leveling system. Altec has developed a kit to reduce the relief pressure of the hydraulic leveling circuit. This will prevent damage to the leveling cylinder mounting pin weld joint by reducing the weld stress. Altec has also developed a kit to repair the lower boom if the side plate has cracked. Altec requires the inspection and repair be completed on the affected units by the next annual preventive maintenance interval or within one year of receipt of the SIL.
SIL 764
Service Bulletin/Repair Instructions
Altec has discovered that the protective fabric hose sock in the upper boom hose carrier on the affected units can become unsecured and slip out of place. This can expose the fiber optic lines to damage, resulting in intermittent operation or failure of the upper controls. Altec requires the following actions to be performed on the affected units no later than 30 days after receiving this SIL. ⢠Inspect the hose sock in the upper boom using the Inspection Procedure beginning on page 2. ⢠Have Altec make any required repairs.
PUN 2020B
Service Bulletin/Repair Instructions
Product Update Notice 2020B reminded customers that they may be unable to store necessary equipment in the body of the cutaway van without exceeding the rear axle capacity. For customers who are not satisfied with the remaining capacity of your vehicle, the tailshelf mounted generator and roof mounted air conditioning unit can be removed. Altec will provide kits to close the opening in the van roof and modify wiring after the generator is removed. Order the A/C Cover Sealing Service Kit, part number 991064376, and the Generator Plug Service Kit, part number 991063374 by calling 1-877-GO ALTEC (1-877-462-5832).
SIL 721
Service Bulletin/Repair Instructions
SIL 721 informed unit owners of potential issues with JEMS units mounted on Dodge chassis Some customers have reported that the engine on the affected chassis will not start after sitting over a weekend time period. Investigation found there was an issue with the Dodge chassisand the ZeroRPM ignition module. Unplugging the ZeroRPM Dodge ignition module and plugging the module back in was found to reset the module allowing the engine to start again. Chassis starting operation will then return to normal. Altec recommends that affected units be modified by adding an ignition reset button to the ZeroRPM system