TSB_2074436_3
Service Bulletin/Repair Instructions
This bulletin provides information when the horn sound quality is poor.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB_2074436_3
This bulletin provides information when the horn sound quality is poor.
TSB_2069078_4
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2069904_3
This bulletin provides information for all models regarding brake sounds.
TSB_2072304_4
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_20741717_15
This bulletin provides information on the GFF test plan required for AC compressor replacements regardless of the concern.
TSB_2075120_3
This bulletin provides information about the general approach for brake vibration concerns.
TSB_2079732_2
This bulletin provides information when there is a paint issue on alloy wheels.
TSB_2082846_1
This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.
SM 01-2026
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
TSB_2073282_1
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the dipped beam is switched on.
TSB_2028902_5
This bulletin provides informaiton when the transmission warning message appears in the cluster; P074100 stored in the TCM.
TSB_2028985_13
This bulleitn procides informaiton when tehre is a transmission warning mssage in the instrument cluster; P074100 is stored in the TCM.
TSB_2059335_7
This bulletin provides information when there are noises from the area around the instrument cluster.
TSB_2074729_3
This bulletin provides informationwhen noises/vibration are detected from front of vehicle in dynamic mode.
TSB_2082323_1
This bulletin provides informaiton when the engine is not running smoothly, misfiring.
TSB_2052680_6
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
AOS-26-25
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.
TSB_2074808_4
The high-voltage batteries in electric vehicles are subject to various ageing effects which could lead to the energy content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years
TSB_2022032_12
This bulletin provides diagnostic information for the vehicle locking system.
TSB_2070568_6
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2081531_1
This Reporting obligation requests that technicians contact the Technical Assistance Center (TAC) when the diagnostic tester refers to this reportin gobligation or to TPI 2033392.
TSB_2023187_8
This bulletin provides informaiotn regarding squeaking noises when steering or maneuvering.
TSB_2081405_1
This bulletin provides informaiotn about various infortainment system complaints.
TSB_2024323_13
This bulletin provides information when the parking assistance gives false warnings.
DC_Audi_CF_ Airbag
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent warning regarding counterfeit replacement airbag inflators that are being installed in used vehicles.
TSB_2024323_12
This bulletin provides information when the parking assistance gives false warnings.
TSB_2021205_10
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2059335_6
This TSB provides information when there are noises from the area around the instrument cluster.
TSB_2052680_4
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
TSB_2080681_1
This bulletin provides information regarding contact checks for event memories, intermittent.
TSB_2060750_5
This bulletin provides information regarding UV leak additive for finding oil leaks.
TSB_2074846_4
This bulletin provides information about vibrations and rotational steering vibrations.
TSB_2056019_5
This bulletin provides information when the anti-theft alarm activates for no reason, or does not activate.
TSB_2061669_3
This bulletin provides service infrmation for workshop mode with Audi connect vehicles.
TSB_2021205_9
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2074808_3
This bulletin provides additoinal information to assist in determining the energy content of lithium-ion high-voltage batteries.
TSB_2018187_18
This bulletin provides information when there are speaker rattles, vibrations, or audio interference.
TSB_2069904_2
This bulletin provides information for all models regarding brake sounds.
TSB_2069078_3
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2075120_2
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
TSB_2030471_8
This bulletin provides informaiton when the license plate mouting bracket threaded inserts are stripped.
TSB_2056386_11
This bulletin provides information about the steering wheel alignment.
TSB_2072304_3
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2074846_3
This TSB provides information regarding rotational and other steerihng wheel vibrations.
TSB_2079732_1
This bulletin provides information when tehre is a paint issue on alloy wheels.
TSB_2047812_8
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator decomissioned).
TSB_2073917_2
This bulletin provides information for when there is a fluid sample request from Product Support.
TSB_2071264_2
This bulleitn provides information whent here are complaints about route guidance with Navigation.
TSB_2041717_14
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of the concern.
TSB_2042920_3
This bulletin provides information when there is corrosion on the tailpipes.
TSB_2070568_5
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2074436_2
This bulletin provides information when the horn sound quality is poor.
AOS-25-47
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
TSB_2060750_4
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
TSB_2027368_7
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
TSB_2010353_6
This TSB provides informatin when the cigarette lighter element does not eject, or the cigarette lighter is inoperable.
TSB_2070568_4
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2042920_2
This bulletin provides information when there is corrosion on the exhaust tail pipes.
TSB_2056019_4
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
TSB_2077320_2
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2031473_6
This service information TSB describes a cosmetic issue after using a car wash.
TSB_2071893_2
This TSB provides damage assessment guidelines for textile seat covers.
Circular_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
Dealer_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
TSB_2077320_1
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2075530_2
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
TSB_2041717_13
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the concern.
TSB_2071185_2
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
TSB-2076945_1
This bulletin provides information about leather care and seat repair.
A6625162049680_3
This TSB provides information when the exterior rubber trim is spotted.
A3725312074822_2
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
A8724952041717_12
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
A6624152046229_5
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
A2724842074729_2
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic mode.
A4424092056386_10
This bulletin provides information regarding wheel alignment.
A0124482014753_13
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
A9124872024323_11
This TSB Provides information when parking assistance provides false warnings.
A9124842018187_17
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
A0024992070568_3
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
A9324342074808_2
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A9624072056019_3
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
A5724652022032_11
This bulletin provides diagnostic information regarding the locking system.
A1524532075530_1
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
CampTip_RNA_Audi
Vehicle Concerns Before Recall Repair Available
A2424632074810_2
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is working; mileage below 50 km/32 miles.
A8724892041717_11
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless of the concern.
A0024932002047_13
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical Assistnce Center (TAC).
A4424082074846_2
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
A0024922031473_5
This bulletin provides informationw hen there are car was brush bristles trapped in the seam between the headlight and fender.
A4524462072304_2
This bulleitn provides information when there is an implausible signal in the ABS/ESC speed sensor.
A4524492075120_1
This bulletin provides information regarding the general approach to brakes rubbing.
A4624592069078_2
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic brakes.
A0124342074976_1
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in petrol.
A9124432074929_1
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
A9324042074808_1
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A0024902074853_1
This bulletin provides service information ror when the fuel tank cannot be fully filled.
A3724222074826_1
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
A4424062074846_1
This bulletin provides information vibrations and rotational steering wheel vibrations.
A2424612074810_1
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not working; mileage below 50 km/32 miles.
A2724762074729_1
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
A3724132074750_1
This bulletin provides information about replacing the clutch end cover.
A3724142074751_1
This bulletin provides information about replacing the clutch end cover.
A3724212074822_1
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
A9124322018187_16
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
A8224002041717_10
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
A0024872002047_12
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center (TAC).
A9124252018187_15
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
A9424822074347_1
This bulletin provides informationw hen there are optical concerns with the tail lights.
DC_Q5 Hybrid
This document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday, June 24.
A9124162018187_14
This bulletin provides information when there are speaker rattles, vibration or audio interference.
A5724432027368_5
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
A9424812073332_3
This bulletin provides information when there is noise while steering.
AWA 24-04
Diagnosed and confirmed malfunction of the vehicle’s AEB system that resulted from failure or malfunction of the AEB system’s control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.
A1124002073917_1
This bulletin provides information for when there is a fluid sample request from Product Support.
A0024852021205_8
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
A872474202012414
This bulletin provides information when the air conditioning is no longer operative; DTC 00457, 00256, 01592.
A9024842032113_9
This bulletin provides general information regarding outside air temperature readings.
A9624962027416_7
This bulletin provides information when the sunglass holder will not close or is stuck closed.
A9024832059335_5
This bulletin provides information when there is noise from around the instrument cluster.
A9424762073332_2
This bulletin provides information for when there is noise when steering.
A2724712067906_5
This bulletin provides information for when DTC P0A7D00 is stored.
A5724342017082_1
This bulletin provides information when the remote control key is inoperative.
A9424742073332_1
This bulletin provides information if there is noise when steering the vehicle.
A9424722073282_1
This bulletin provides information on visual concerns with the headlight lens.
A4824602073033_1
This bulletin provides information for when the steering column adjustment does not work.
A4824612034351_1
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
AWA 24-01
This Document informs dealers on the new oil consumption & piston fracture warranty extension for 2012 A4, A5, A6, Q5 & TT / 2013 A4, A5, A6, Q5 & TT / 2014 A4, A5, A6, Q5 & TT / 2016 A3 & TT / 2017 A3 & TT vehicles
A9124632044694_3
This bulletin provides information pertaining to MMI Navigation database concerns.
DC_Closure 19N8
SERV_ACT - After-Run Coolant Pump - Closure Notice
A6424972062618_4
This bulletin provides information when the frameless window auto-drop function is inoperative in freezing weather.
A0023822047812_7
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via the Mirror Server.
A9023672072568_1
This bulletin provides information for when the lane change assist radars cannot be calibrated after replacement.
A912306202432310
This bulletin provides information when the parking assistance provides false warnings.
A4523362072304_1
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
A0123972072121_1
This bulletin provides information for when the MIL/EPC light is illuminated, DTC P042000 or P043000, Catalyst system, bank 1 or 2 efficiency below thresh hold.
A9023562032113_8
This bulletin provides general information about the outside air temperature reading.
A6623042030471_7
This bulletin provides information for when the license plate mounting bracket threaded inserts are stripped.
A0023812070568_2
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
A9423672071954_1
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
A7423262071893_1
This bulletin provides damage assessment guidelines for textile seat covers.
A0023762071721_1
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans (Ghost faults).
A0123812028842_4
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
A0023742052680_4
This bulletin provides information on the additional reporting requirements for safety related inquiries.
A0023732061669_2
This bulletin provides information on workshop mode with Audi connect vehicles.
A0023712070568_1
This bulletin provides information on professional noise analysis with the VAS 611 015 PICO NVH Tool.
A9123262071264_1
This bulletin provides information for when the customer has concerns about the navigation route guidance.
A6423922020552_1
This bulletin provides information for when exterior glass cleaning is needed.
A8723452041717_9
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
A9023322059335_4
This bulletin provides information for when there is noise from the area around the instrument cluster.
A922336203815115
This bulletin provides information for when the washer solvent level warning is on.
A4623452070679_1
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29.
A4823412028220_1
This bulletin provides information for instances where the steering wheel leather is damaged.
A102326201828810
This bulletin provides information on checking for debris when replacing an engine.
A8723442010146_8
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
A9123062010146_8
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
A9423652061922_3
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and taillights.
A5723082027406_5
This bulletin provides information regarding the Audi advanced key.
A922335203815114
This bulletin provides instructions for when the washer level warning is on but the reservoir is full.
A0023702021205_7
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
A0023692031473_4
This bulletin provides information for when car wash bristles become stuck in the body gap between the headlight and fender.
A912394201818713
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference.
A9423632061922_2
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty submissions.
A4423992056386_9
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4423982056386_8
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4623432069904_1
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
A9023222032113_7
This information bulletin contains a background on the outside air temperature reading.
A192336202530314
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
A6423882047061_5
This bulletin describes the process to clean sticker residue from the windshield.
A4023512023187_7
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and repair is not needed.
A402352202431813
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9123832037809_1
This bulletin provides information on how to update the navigation map.
A9623822056019_2
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored.
A462341203418123
This bulletin provides instructions for brake noise analysis and handling.
A012341201475312
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A9223332038151
This bulletin provides instructions for when the washer solvent level warning is on in the DIS but the washer solvent level is correct.
DC_Alternator_6
Support for Customers Affected by Alternator Back-order
A6423862047061_4
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production.
A6623942049680_2
This bulletin provides instructions for when the exterior trim has spots.
A4423972022563_2
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph.
DC_Alternator_4
Support for Customers Affected by Alternator Back-order
DC_Alternator_5
Support for Customers Affected by Alternator Back-order
A8023122062583_2
This bulletin provides instructions for when the customer advises that there is insufficient or uneven cabin heating from the HVAC system.
DC_Alternator_3
Support for Customers Affected by Alternator Back-order
A9123592036576_7
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s).
A4623402069078_1
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
DC_Alternator_2
Support for Customers Affected by Alternator Back-order
DC_Alternator
Support for Customers Affected by Alternator Back-order
DC_RECALLS
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
A572200202203210
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A1922332061604_5
This bulletin contains instructions for resolving a coolant leak.
A462234203418122
This technical service bulletin provides troubleshooting for brake noise.
A4822342065978_2
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly.
A922230203815112
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A642285202055211
This bulletin provides instructions on how to properly clean exterior glass.
SM 48-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4622332051095_7
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462232203418121
This technical service bulletin provides troubleshooting for brake noise.
SM 47-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4522262067132_1
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs.
A442292202256321
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A8722272041717_8
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A872225201014617
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation system.
A402238202431812
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
A9022572032113_6
This is an informational bulletin containing information about the outside temperature reading.
A9022582059335_3
This bulletin contains information on noises from the instrument cluster installation area.
A462230203418120
This technical service bulletin provides troubleshooting for brake noise.
A402237202431811
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
DC_20220329
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
A9122892037809_9
This informational bulletin contains instructions about updating the navigation map.
A1722172060750_3
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A4622282051095_5
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A9122752024323_9
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A442287202256320
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A462226202258411
This informational bulletin provides diagnostic information for brake conditions.
A462227203418119
This technical service bulletin provides troubleshooting for brake noise.
A6922792065962_1
This bulletin advises on identifying when a foreign object has obstructed normal operation of the seat belt.
A192228202530313
This bulletin contains instructions for identifying and mixing factory fill coolants.
A192227202530312
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4421862056386_7
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4021302023187_6
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or maneuvered.
A4021312024318_1
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A002155201173212
This bulletin contains general instructions for software updates.
A4421842065160_1
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
DC 20210928
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
A9121342018187_1
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A012111203300125
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A8721162041717_7
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A0121102028842_3
This informational bulletin gives instructions for identifying chip tuning.
A4821092028220_9
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty.
A4421832056386_6
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A1921222046712_3
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A2021352043357_1
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A0021482021205_6
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
A0021472031473_3
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again.
A4821052063527_1
This bulletin contains instructions for calibrating the steering angel sender G85.
SM 44-2021
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
147820373071
ECM software needs to be updated.
A9121042024323_8
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0021442052680_3
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage).
A1021222018288_9
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
A9021032058077_5
This bulletin contains instructions for determining unexpected Audi presense interventions.
A4421822056386_5
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A6421802020552_1
This bulletin provides instructions on how to clean exterior glass.
A8721132010146_1
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
ELSAallignAudi
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
A9021002032113_5
This information bulletin contains a background on the outside air temperature reading.
AWA 21-04
This Document informs dealers on the new turbo warranty extension for 2013-2016 A4, 2013-2017 A5/Q5, and 2012-2015 A6 vehicles
A4021242016453_4
This bulletin contains instructions for determining if bushings need to be replaced.
A9021982059335_2
This bulletin contains information on noises from the instrument cluster installation area.
A6421792047061_3
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A1921152061604_3
This bulletin contains instructions for resolving a coolant leak.
A5721752022032_9
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A9121862062713_1
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
A8021112062583_1
This bulletin contains instructions for addressing an insufficient or uneven heating performance from the HVAC system.
A9421362023322_3
This informational bulletin contains information on the different shading of LED headlights.
A6421772062618_1
This bulletin contains instructions for front and/or rear doors cannot be opened or closed in freezing weather.
A1321132062387_1
This bulletin contains instructions for determining if a repair is needed when coolant touches a poly V-belt and/or a toothed belt.
A1921142061604_2
This bulletin contains instructions for resolving a coolant leak.
A9121762037809_8
This informational bulletin contains instructions about updating the navigation map.
A4621252054385_2
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill).
A4421802056386_4
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4621222051095_4
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462123202258410
This informational bulletin provides diagnostic information for brake conditions.
A462124203418118
This technical service bulletin provides troubleshooting for brake noise.
A4421792022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A6621692030471_6
This informational bulletin covers the condition of when license plate mounting bracket threaded inserts are stripped.
A9421332061922_1
This informational contains instruction on how to document optical concerns for warranty claims.
A1721122060750_2
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A9121642024323_7
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A9120572036575_6
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
SM C-2020
This special notice is to inform dealers to return the part numbers listed (State of California only).
A1920102061604_1
This bulletin contains instructions for resolving a coolant leak.
A0020432061669_1
This informational bulletin contains instructions for Audi connect before performing any MMI work.
SM 69-2020
This special notice is to inform dealers to return the part numbers listed and order the superseded part numbers
A9120382061397_1
This bulletin contains repair instructions for voice recognition or Bluetooth quality issues that are related to the microphone.
A012093203300124
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9120242026611_7
This bulletin contains a guide for troubleshooting HD radio issues.
A1720112060750_1
This bulletin contains instructions for using the UV additive to find engine oil leaks.
21AUTIRECHAINS
Added new graphic to reflect where to find MY 21 information
A0120882033001_2
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9120112037809_7
This informational bulletin contains instructions about updating the navigation map.
A9020652032113_4
This information bulletin contains a background on the outside air temperature reading.
Audi Part Labels
Recall Reminder Part Labels
A012072203300122
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A3720012039650_2
This bulletin contains instructions for addressing a leak from the transmission oil pan gasket or transfer case.
A1720062028440_5
This informational bulletin explains when the range display is empty in the on-board computer.
A1920042025303_1
This bulletin contains instructions for identifying and mixing factory fill coolants.
A0020382039206_3
This informational bulletin contains instructions on how to use the QR code in a TSB.
A9120732026390_7
This bulletin contains instructions for correcting the phonebook.
A9120702044694_2
This technical service bulletin provides troubleshooting for issues with the navigation map database.
A4020052024318_9
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9120652036576_6
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
A6420742020552_9
This bulletin provides instructions on how to clean exterior glass.
A012062203300121
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A0020372059437_1
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing some issues.
A872005201014615
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
A9020442032113_3
This information bulletin contains a background on the outside air temperature reading.
A9020452059335_1
This bulletin contains information on noises from the instrument cluster installation area.
SM 25-2020
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A0020362002047_1
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
A012058203300120
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A6420722047061_2
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A012054201475311
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A942020201780613
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A5120132009967_1
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A012046201475310
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A912039201818711
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
Circular19N8REV1
SERV_ACT - After-Run Coolant Pump - Updated claiming and work instructions: A single part number per criteria will now be used.
A4420732056386_3
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A921924203815111
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A0019292031473_2
This informational bulletin contains instructions for when car wash bristles are stuck in the headlights. 2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant
A9419182012749_1
Exterior lights, moisture accumulation 2013-2021 A3 Cabriolet, 2016-2018 Sportback, 2004-2005 A4 Cabriolet, 2004-2008 S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8
20AUTIRECHAINS
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
AWA 19-06
The communication contains the details of the water pump extended warranty.
A9219232038151_1
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct. 2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant
A4419712022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7
145320381292
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A9119032041430_7
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A1919992052657_3
This informational bulletin contains details on conditions for replacing the water pump and/or thermostat housing. 2015-2019 A3 Cabriolet, 2017-2018 S3 Cabriolet, 2018-2019 A5 Sportback, S5 Sportback, 2013--2019 TTR
A4819822034351_9
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A4019972018194_9
This bulletin contains repair instructions for leaking shock absorbers.
SM 80-2019
Parts are currently blocked from sale at this time.
A0019262052680_2
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage.
ATUBody2019
Body components - Examples of customer misuse
A9119922041430_6
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A9119932037087_4
This bulletin contains instructions for enabling text message notifications through the MMI system.
A0019252011732_1
00 Software Version Management (SVM), operating instructions
A9419132017806_1
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A9119882024323_6
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A1719982028440_4
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
A9619432056019_1
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off. Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
AWC 19-05
This communication is issued to inform dealers of updated shipping regulations related to lithium ion batteries.
AWC 19-04
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8
A011919203300119
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A4819792028220_8
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe
A0019222047812_6
This informational bulletin contains instructions for setting up and using the SD Creator program. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A8719912041717_6
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A9019192032113_2
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe
A9119652050565_2
This bulletin contains general software update instructions for vehicles with PR Code 7UH. 2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster
A0019212052680_1
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe
A201918204335711
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201916203507314
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.
Circular - 19N8
After-Run Coolant Pump
Dealer - 19N8
After-Run Coolant Pump repair available.
A201913203507313
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. Vehicles also include 2015 A3 Cabriolet and 2012 RS7,
A571954 20220328
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A961934 20489272
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A201911 2043357
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A011902 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A921916 2038151
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A441969 2022563
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A461903 2034181
This technical service bulletin provides troubleshooting for brake noise.
A001915 2047812
This informational bulletin contains instructions for setting up and using the SD creator program.
A011894 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A911821 2051527
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A011893 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A401887 2035854-
This bulletin contains repair instructions for when a rattle or knocking noise is head when driving over bumps and the vehicle has 75mm hydro-bushings.
A011879 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A911800 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A911899 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A911895
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
A911895 2026657-
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
A911870 2041430_
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A971860 2036764_
This bulletin contains repair instructions for when the vehicle will not start and DTC P068A00 is stored.
A961721 2048927-
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A911760 2040406
This bulletin contains instructions on a repairing an issue when the GPS does not have the correct location or reception.
A001702 2035505
This repair authorization is for special VINs that are part of the Audi on Demand and Audi at Home program.
A511711 2009967-
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A911750 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
A911745 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
A911743 2042097-
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI navigation.
A201796 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A011732 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A011730 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
SM 52-2017
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation 14s.
A201795 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A941791 2012749-
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
A911736 2024323-
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A201794 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201792 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401774 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A191789 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A911733 2021780-
This informational bulletin contains procedure information for DTC 00468 with error messages on the radio display.
A401770 2018194-
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
A401768 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
SM 44-2017 EN
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward.
A461772 2047830
This informational bulletin contains instructions for proper brake maintenance.
A201790 2043758
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401766 2024318
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A911732 2033355-
This informational bulletin contains information on why ACC sensor could be deactivated.
A171784 2038119-
This bulletin details instructions on handling when the oil minimum message appears but the oil level is above minimum but not overfilled.
A481774 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A201789 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A441764 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A171782 2010043-
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil change.
A301722 2019850-
This technical service bulletin provides guidelines for diagnosing the clutch plate.
A011713 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A011712 2047707-
This informational bulletin provides instructions for when DTC P195000 appears but there is no customer concern.
A421737 2038689-
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle id driven over bumps.
A911724 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
A401761 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A481772 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A571740 2047432-
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored.
A201788 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A571738 2017082-
This informational bulletin contains instructions for sychronizing the remote key after the battery has been disconnected or replaced.
Edition76
Technical bulletins and updates
ATE-17-05
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
A011703 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A661761 2038652-
This technical service bulletin provides repair instructions for paint flaking off the radiator grille or front license plate holder.
A011701 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A191777 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A201785 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201784 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A911700 2041430-
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A201683 2043357_
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A151631 2045732_
THIS BULLETIN PROVIDES INFORMATION ON REMOVING A DAMAGED SCREEN FROM THE NON-RETURN VALVE.
A911693 2028141_
THIS BULLETIN PROVIDES SOFTWARE UPDATE INFORMATION FOR THE MMMI 3G OR RMC FOR NAVIGATION DATA.
A921614 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A871679 2041717-
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan.
A911690 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
A911688 2045927-
This bulletin provides repair instructions for when the rearview camera does not work or flickers with DTC 02283.
A011684 2037307-
This bulletin provides information regarding a software update for an )2 sensor DTC.
A151630 2045732-
This bulletin provides information on removing a damaged screen from the non-return valve.
A441662 2010334-
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
A441663 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A661657 2038652-
This technical service bulletin provides repair instructions for paint flaking off the radiator grille or front license plate holder.
A921613 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A921612 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A001684 2037949-
This technical bulletin provides instructions for an an error message and updating with an SVM code.
A911681 2040406-
This bulletin contains instructions on how to fix when the GPS does not have the correct location or reception.
A911677 2044940-
This technical service bulletin provides software update instructions to fix an issue that prevents Google Earth from loading.
24CO
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. AS A RESULT, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY COME ON EVEN THOUGH THE CATALYTIC CONVERTERS ARE WORKING PROPERLY. IF THE MIL IS ON, A VEHICLE WILL NOT PASS AN EMISSIONS INSPECTION.
A37166820300075
THIS BULLETIN PROVIDE INSTRUCTIONS FOR WHEN THERE ARE HARSH GEAR SHIFTS BUT THERE IS NO FAULTS STORED AND YOU CAN DUPLICATE THE CONCERN.
A94168220175666
THE BULLETIN STATES A NORMAL FUNCTION OF THE HEADLIGHT SWITCH AND HOW TO FIX BUT NOT REPLACE. DEALER IS TO ADVISE CUSTOMER ON WHY THE HEADLIGHT SWITCH PRESSES IN.
A91167120404066
THIS BULLETIN CONTAINS INSTRUCTIONS ON HOW TO FIX WHEN THE GPS DOES NOT HAVE THE CORRECT LOCATION OR RECEPTION.
A20167620437584
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A911667 2030465-
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A911667203046510
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
82B8 CIRCULAR
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
A20167520437583
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A66165520386525
THIS TECHNICAL SERVICE BULLETIN PROVIDES REPAIR INSTRUCTIONS FOR PAINT FLAKING OFF THE RADIATOR GRILLE OR FRONT LICENSE PLATE HOLDER.
82B8
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
82B8 DEALER LETT
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
A01166820404914
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INSTRUCTIONS TO RESOLVE A COOLANT WARNING AND STORED DTC.
A9116612044940-1
THIS TECHNICAL SERVICE BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO FIX AN ISSUE THAT PREVENTS GOOGLE EARTH FROM LOADING.
A91166120449401
THIS TECHNICAL SERVICE BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO FIX AN ISSUE THAT PREVENTS GOOGLE EARTH FROM LOADING.
A19167220431422
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE THE AUXILIARY COOLANT PUMP IF CERTAIN DTCS ARE STORED.
A9116562040406-5
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
A91165620404065
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
2014 A5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2015 A5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A40165520243184
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR CORRECTING A CLICKING SOUND FROM THE WHEEL BEARING(S).
A5/S5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A57162620220327
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INFORMATION FOR THE VEHICLE LOCKING SYSTEM.
A91164720304658
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A91164820414303
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE REAR CAMERA WIRING HARNESS.
A91164920304659
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A201671 20437582
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE COOLANT THERMOSTAT WITH A NEW PART NUMBER TO RESOLVE A STORED DTC.
A17167520381197
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A4416612034445
THIS TECHNICAL SERVICE BULLETIN NOTIFIES THE READER THAT IF THE TPMS MESSAGE APPEARS BRIEFLY AFTER THE ENGINE IS STARTED AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM.
A20167020433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A2016720433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A24165420440032
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
A96160720295633
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A17167220381196
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A20166720433571
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO UPDATE THE ECM SOFTWARE TO RESOLVE AN ISSUE THAT CAUSES DTC P046100.
A17167120381195
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A96160620295632
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A24165320440031
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
A91163920420133
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC.
A20166620437581
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A20166420438921
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V6 ENGINES.
A20166520415947
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH 4-CYLINDER ENGINES.
A011656 2040491-
The technical service bulletin is in regards to the MIL being on due to DTC P1B1C00 (coolant pump mechanical malfunction) being stored in the ECM. "Coolant System: Fault Turn Off Engine" and the Coolant symbol appear in the information panel. Condition can be caused by a defective thermostat or the diagnostic software is incorrectly displaying the warning.
A481669 2034351-
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly. The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead.
A481668 2043629-
Steering angle sensor cannot be programmed. The steering angle sensors cannot be calibrated and the steering end stops cannot be adapted on a vehicle with dynamic steering.
A441660 2034445-
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. This occurs after the engine is started, the message "TPMS" appears briefly and then turns off. There are no DTCs stored.
A171668 2038119-
The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level. There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A191667 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A661546 2030471-
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped.
A961604 2042811-
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting. The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. The Audi connect Gen1 system includes all vehicles that utilize a removable plastic SIM card. The Audi connect Gen2 system includes all vehicles that utilize an embedded SIM card. The root cause of all complaints cannot be attributed to the vehicle hardware because of the backend server configurations that need to be correct in order for Audi connect to work. For most sporadic complaints, the issue typically resides with the MBB backend server or with the source data provider (Google, INRIX, etc.), and not with the vehicle. In rare cases, the mobile network operator (AT&T, T-Mobile) can be the cause of the complaint. For most static complaints, the issue can be attributed to the user account subscription or possibly the vehicle hardware.
A191666 2043142-
The MIL is sporadically on. One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
A201659 2041594-
MIL on; (DTC P046100 - Fuel level sensor, circuit range/performance). MIL is on during normal driving conditions, city or highway at any speed.
A011652 2040491-
MIL on (DTC P1B1C); message in information panel: "Coolant System: Fault Turn Off Engine" The condition is caused either a defect with the thermostat (in model year 2012 and 2013 vehicles) or The diagnostic software is incorrectly displaying the warning. No technical issue exists. Solutions are an improved thermostat installed in production and the diagnostic software has been updated.
A191665 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A401549 2018194-
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A911529 2013422-
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A001578 2021205-
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement.
A171568 2028440-
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A201559 2011703-
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.
155820415945
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201558 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-56 dated November 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A911526 2042097-
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.
A401548 2042603-
When the vehicle is driven between 35 mph and 75 mph, a noise can be heard in the front of the vehicle. The customer may say that the noise is coming from the steering column area, and may describe the sound as buzzing, humming, whistling, whining, grinding, howling, and/or droning. The best way to understand the complaint is to discuss it with the customer. Faulty wheel bearing(s) may cause the noise.
A241551 2038212-
Supersedes Technical Service Bulletin Group 24 number 14-50 dated August 28, 2014. The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
155620415944
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201556 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-55 dated November 6, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
Fluid Capacity C
This document contains the fluid capacity chart.
A911524 2026611-
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The
A911528 2042013-
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. The following message appears in the MMI: ?This service is currently unavailable. Please try again later.? The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Additionally, if the vehicle is a model year 2016 A6, A7, or TT, the customer may not be able to see speed and flow traffic information in the navigation map screen, and may consistently see that no traffic reports are available. For these vehicles, traffic is provided by INRIX online.
155520415943
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201555 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-50 dated October 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
A571516 2024111-
Supersedes Technical Service Bulletin Group 69 number 12-22 dated February 13, 2012. After the comfort system central control module, J393 (address word 05) is replaced, the control module cannot be coded via SVM spec/actual. Any time a comfort system central control module, J393 (address word 05), is replaced, the new control module must be coded and parameterized with online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then an SVM code is required to code and parameterize the new control module. The SVM code can be found in Parts Bulletin 9-101, which can be found on the etkainfo.com web site.
A201554 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A201552 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A511510 2009967-
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing.
A461525 2022584-
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.
A201550 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-47 dated August 5, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A911522 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-10 dated August 25, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
A201548 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-46 dated May 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911519 2041430-
Supersedes Technical Service Bulletin Group 91 number 15-04 dated July 22, 2015. The customer complains that the rearview camera image is not displayed on the MMI display. DTC 02203 (audio/video input 1) is logged in the rearview camera system control module. An issue with the wiring harness may cause the condition.
A461523 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. New brake pads and/or discs have not been properly imbedded after installation. Aftermarket pads or discs are installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time. Discs are grooved. There is chemical contamination on the braking surface of the brake disc due to wheel or tire cleaner being sprayed directly onto the brake disc. There are ?pad marks? on the brake disc as a result of brake pad material transferring to the discs. Pad marks can occur when a vehicle has been parked for long periods of time in a wet or snowy environment.
A441557 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A511509 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing.
A911517 2042013-
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern.
A871570 2041717-
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception.
A961501 2019260-
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
Email Mandatory
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
A171565 2038129-
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A191562 2025303-
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A9615002027416-6
Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
A911512 2036575-
Supersedes Technical Service Bulletin Group 91 number 15-80 dated March 20, 2015. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user?s myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations, accessing weather or other online information, or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. 2016 A6 and A7 vehicles have a known software issue that requires the myAudi PIN to be entered with each ignition cycle. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. Thi
A871567 2041717-
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
A571512 2028207-
Supersedes Technical Service Bulletin Group 57 number 12-62 dated January 9, 2012. The trunk cannot be unlocked with the button on the remote, with the button in the driver?s door panel, or with the handle on the lid of the trunk. Vehicles have a ?VALET? button in the glove box that activates the valet parking feature, which prevents unauthorized access to the trunk. When the valet parking feature is activated, the trunk can only be opened mechanically with the key.
2041594/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201547 2041594-
The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A211522 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-21 dated November 26, 2014. The MIL is on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall off due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
A9115082033313-3
Supersedes Technical Service Bulletin Group 91 number 14-46 dated June 25, 2014. Adaptive Cruise Control (ACC) does not work. The message "ACC no sensor vision" appears in the cluster. DTCs are logged in the distance regulation control module.
TSB-91-15-08
AUDI: SOME VEHICLES EXPERIENCE A DEACTIVATION OF ADAPTED CRUISE CONTROL (ACC) DUE RADAR SENSOR FAILING TO SEE OBJECTS FOR PERIOD OF TIME WHEN SNOW, LEAVES, WATER SPRAY BLOCKS RADAR SENSOR VISION. MODEL 2013-16 A4, A5, CABRIOLET, Q5. *PE
A481566 2034351-
Supersedes Technical Service Bulletin Group 48 number 15-65 dated March 23, 2015. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
TSB-91-15-04
AUDI: SOME VEHICLES EXPERIENCE, INTERMITTENTLY, THE MMI DISPLAY FAILING TO DISPLAY REARVIEW CAMERA IMAGE DUE TO POSSIBLE WIRING HARNESS ISSUE. MODEL 2013-16 A4, A5, A8, Q3, Q5, Q7. *PE
TSB-96-15-98
AUDI: SOME VEHICLES, WHILE DRIVING, WOULD RECEIVE FALSE WARNINGS LIGHTS OF DOOR MIRRORS, OF VEHICLES IN BLIND SPOT WHEN NO VEHICLE IS PRESENT, FROM SIDE ASSIST. SOFTWARE NEED TO BE UPDATED. MODEL 2014-15 A5, S5, RS 5, CABRIOLET. *PE
A1915612025303-5
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A0115292041097-1
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
A301519 2019850-
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
SB-01-15-29
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
A011528 2040508-
Supersedes Technical Service Bulletin Group 01 number 15-21 dated April 29, 2015. The MIL is on. DTC P046100 (Fuel level sensor circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). DTC P046100 can be caused by miscalculations within the ECM software.
A911598 2018187-
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A871564 2010146-
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
A961597 2034733-
Supersedes Technical Service Bulletin Group 96 number 13-71 dated July 22, 2013. The customer complains that after the vehicle is started, the name of the current radio station or media track is not shown in the driver information system (DIS). After the music input is changed to a different source and then changed back (i.e., media to radio to media or radio to media to radio), the radio station or media track information is shown in the DIS. Incorrect software.
A911594 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
A911595 2040926-
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
Executive Servic
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
A011524 2040491-
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
A911590 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-87 dated May 18, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). Q7 and Q3 vehicles are not affected by this condition. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A911589 2017425-
Supersedes Technical Service Bulletin Group 91 number 14-30 dated April 7, 2014. On generation III Concert and Symphony radios, the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence.
A171563 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A971548 2013504-
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
A911588 2026390-
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
A871563 2010146-
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911587 2040406-
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle's actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. No DTCs related to the GPS antenna or MMI system are present. If the sky view is blocked because the vehicle is in a parking structure, below ground, or next to large buildings, it is normal for the GPS location or vehicle direction indicated on the MMI navigation map to not match the vehicle's actual location or direction of travel. The blocked sky view prevents the vehicle from receiving satellites, and the system may be temporarily lost until four satellites can be received. This is a normal condition, and is not related to the condition described above. Replacing the MMI main unit will not change this behavior. A potential failure in the internal hardware of the MMI main unit can cause the GPS signal to be blocked, even if good reception is available. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A201546 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-45 dated May 6, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911583 2030465-
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814. This bulletin only applies to vehicles with MMI3G+ Navigation (PR Number "7T6") and to vehicles with MMI3G+ Navigation, but without Audi Connect (PR Number "7T6" with additional PR code of "PND"). Continual improvements to MMI software provides solutions to issues experienced in the field.
A661553 2038652-
Supersedes Technical Service Bulletin Group 66 number 15-45 dated January 20, 2015. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A201545 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-43 dated December 19, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A921510 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
A011521 2040508-
The MIL is on. DTC P046100 is stored in the ECM. DTC P046100 can be caused by miscalculations within the ECM software.
A391515 2028902-
Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
A911582 2029903-
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
A941565 2012749-
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
A941566 2017566-
Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision.
A001575 2035505-
Supersedes Technical Service Bulletin Group 00 number 13-54 dated October 10, 2013. Audi of America (in conjunction with AUDI AG) is conducting a pilot program in the USA with a limited number of specially-built vehicles. These vehicles have a persistent internet connection and are designed to be accessed and started without the need for a traditional remote key. Instead, these vehicles use NFC (Near-field connectivity), or an iPhone with the Audi on Demand app, utilizing Bluetooth connectivity. The customer must leave the NFC card with the vehicle in order for the vehicle to be accessed and started.
A741521 2036572-
Supersedes Technical Service Bulletin Group 74 number 14-19 dated May 9, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damaged is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is moved back far enough to make contact with the rear seat headrest.
A961594 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-79 dated December 5, 2013. Audi side assist deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information panel. The system can be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Workshop finds that sporadic DTCs are stored in the lane change assistance control module, Audi side assist can be activated without issue, no obstructions found on the outside or inside of the bumper, no rework of the bumper can be found, the control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found on the inside or on the outside rear bumper area, and the control module mounting brackets are not broken or loose.
A961592 2039096-
Supersedes Technical Service Bulletin Group 96 number 14-88 dated November 25, 2014. Customer may report that Audi side assist is providing false warnings (no vehicle is present in the blind spot). No faults related to Audi side assist are stored. This TSB does not refer to warning messages on the instrument cluster. It applies only to false displays of the warning lights in the door mirrors. Incorrect software parameterization.
A661549 2030471-
Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
A481565 2034351-
Supersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A911579 2038824-
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A911580 2036575-
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
A101511 2018288-
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A191557 2040043-
Customer states that engine overheats. No MIL. No related DTCs are stored. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the overheat condition for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above. No changes to production have been made, as no issue has been identified.
A911578 2011500-
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A011514 2014753-
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A171557 2010043-
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A941564 2017806-
Supersedes Technical Service Bulletin Group 94 number 15-60 dated February 12, 2015. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A151526 2039995-
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner.
A461505 2038056-
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit.
A011509 2037307-
Supersedes Technical Service Bulletin Group 01 number 14-78 dated May 28, 2014. MIL is on due to DTC P013E00 being stored in the ECM. ECM software needs to be updated.
A011507 2028344-
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
A941560 2017806-
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A461502 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A461500 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time
A661545 2038652-
Paint flakes off radiator grille or license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A901552 2039429-
The vehicle horn sounds abnormal or is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Contact the Audi Technical Assistance Center (TAC) before replacing any parts. No changes to production have been made, as no issue has been identified.
A461599 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
Edition117
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
20 14 43 2035073
EVAP System Leak Detected NVLD very small leak
20144320350737
System Leak Detected.
2035073/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911472 2024323-
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
00147020392061
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
2038689/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4214222038689
Rattle noise from rear suspension
42142220386891
Rattle noise from rear suspension
A001470 2039206-
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
A421422 2038689-
Clunking or rattling noises are heard from rear suspension area when vehicle is driven over bumps. These noises can be caused by an improperly seated rear bump stop (which occurs when the rear bump stop was not fully inserted into the rear shock absorber mounting during PDI).
441456202256311
Steering wheel shimmy, vibration, and/or oscillation
A441456 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
A901451 2021151-
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
Accessories Oper
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin.
Edition114
Wastegate linkage dissconnected
142120390062
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211421 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-20 dated November 17, 2014. MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
EDITION 113
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition113
Technical bulletins and updates
145320390181
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A191453 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
142020390061
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211420 2039006-
MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
Edition112
Technical bulletins and updates
A851422 2033596-
Supersedes Technical Service Bulletin Group 85 number 14-20 dated February 24, 2014. DTCs may be stored in the heating and air conditioning electronics control module. A faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower can cause Improper operation of the fresh air blower.
A171453 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A911469 2038824-
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
Edition110
Technical bulletins and updates
44145520103346
Tightening wheel bolts
48146320282204
Steering wheel leather damage, all vehicles
A481463 2028220-
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
EDITION 108
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition108
Audi Elsa Newsletter
2038652/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A661443 2038652-
Supersedes Technical Service Bulletin Group 66 number 14-42 dated October 9, 2014. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A871458 2035582-
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
A911466 2020399-
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
A911467 2021037-
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
149820381661
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
87D9UPDATEa
AC Pressure/Temperature Sensor
87D9a
AC Pressure/Temperature Sensor (NVLW)
A011498 2038166-
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
Update Bulletin
This Update has been proactively released to prevent the following condition from occurring in the vehicle. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
87D9
AC Pressure/Temperature Sensor
A441455 2010334-
Supersedes Technical Service Bulletin Group 44 number 13-46 dated December 9, 2013. Wheel bolt requires torque adjustment.
144120350736
The NVLD pressure switch may erroneously detect a very small leak.
2035854/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2038652/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4014432035854
Rattling or knocking noise from front end when driving over bumps
40144320358544
Rattling or knocking noise from front end when driving over bumps
A201441 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-34 dated June 26, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A401443 2035854-
Supersedes Technical Service Bulletin Group 40 number 14-42 dated July 8, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.
A661442 2038652-
The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
Edition106
Audi Elsa Newsletter
37 14 48 2030007
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.
37144820300075
Customer may report harsh shift concerns; no faults are stored and concern is reproducible
A371448 2030007-
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.
A911463 2028190-
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
Edition105
Audi Elsa Newsletter
A641436 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Edition104
Audi Elsa Newsletter
143820381132
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038113/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201438 2038113-
Supersedes Technical Service Bulletin Group 20 number 14-36 dated August 14, 2014. MIL on.DTC P310B is stored in the engine control module, J623 (address word 01), with symptom code 6183.
Edition103
Audi Elsa Newsletter
A921409 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
149120288422
Customer vehicle is fitted with unauthorized ECM tuning.
A011491 2028842-
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.
143720382761
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038276/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201437 2038276-
DTC P045600 is stored in the engine control module (ECM), J623 (address word 01). Note that this repair authorization applies only to a specific list of VINs. If this repair authorization does not appear in ELSA when your VIN is entered, it does not apply.
2035919/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911458 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-53 dated July 24, 2014. MMI 3G+ GPS location is inaccurate (MY13, MY14, & MY15).
2038212/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24 14 50 2038212
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
A241450 2038212-
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
441454203027510
Repair Authorization
145020381291
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
143620381131
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038113/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-20-14-36
AUDI: DIAGNOSTIC TROUBLE CODE (DTC) P310-B00, LOW FUEL PRESSURE REGULATION OUTSIDE OF SPECIFICATION, SPORADIC/PASSIVE. SYMPTOM 6183. MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2014 A4, A5, A5 CABRIOLET, A6, A7, A8, Q5. *PE
44145320302759
Repair Authorization
2038056/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46149420380561
Brake pad wear warning - pads not at minimum
44145220302758
Repair Authorization.
A001467 2002047-
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC).
00146620379491
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
2024683/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A001466 2037949-
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
A911455 2024683-
Supersedes Technical Service Bulletin Group 91 number 13-87 dated June 19, 2013. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.
Edition96
Technical bulletins and updates
Edition96-1
i-wire new wiring diagram application
2035919/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911453 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-41 dated April 30, 2014. MMI 3G+ GPS location is inaccurate (MY14 & MY13).
A961485 2027416-
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
2037756/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A461491 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A911452 2037756-
The customer complains about GPS navigation issues that may be antenna-related. No DTC entry is logged. This bulletin should be performed before any other bulletins that cover specific customer complaints. If the GPS antenna cable became partially connected during assembly or during a repair, it may still function. But, the partially-connected cable can cause an intermittent issue that does not cause a DTC to be logged.
A571402 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
001465201173210
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
A001465 2011732-
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
46148620225845
Brake pulsation diagnostic guidelines
A461486 2022584-
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
Edition94
Pending service solutions and bulletins
48146120360322
Steering feels stiff when turning
A481461 2036032-
Supersedes Technical Service Bulletin Group 48 number 13-56 dated December 13, 2013. The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.
A911450 2018187-
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
AUD4927ENG
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
TSB-48-14-61
AUDI: WHEN TURNING, THE STEERING FEELS STIFF AND OCCURS EVEN WHEN VEHICLE IS STATIONARY. INTERMEDIATE STEERING SHAFT NEEDS TO BE IMPROVED. MODEL 2008-2014 A4, A5, Q5. *PE
2035854/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4014422035854
Rattling or knocking noise from front end when driving over bumps
40144220358543
Rattling or knocking noise from front end when driving over bumps
A401442 2035854-
Supersedes Technical Service Bulletin Group 40 number 14-39 dated February 13, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.
EDITION 93
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition93
Technical bulletins and updates
4014402023187
Squeaking noises when steering or maneuvering
40144020231874
Squeaking noises when steering or maneuvering
4014412018194
Shock absorber leaks: assessment aid
40144120181946
Shock absorber leaks: assessment aid
A401440 2023187-
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A401441 2018194-
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
Edition92
Idenifying and mixing factory fill engine coolants
143420350735
The NVLD pressure switch may erroneously detect a very small leak.
20344445/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44145120344452
Message "TPMS" in instrument cluster
A201434 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A441451 2034445-
Supersedes Technical Service Bulletin Group 44 number 13-38 dated July 11, 2013. Scenario A is after the engine is started, the message "TPMS" appears briefly then turns off. No DTCs are stored. Scenario B is the message "TPMS" appears constantly. DTC 03159 (tire pressure monitoring in ESP function) is stored in the ABS control module, J104 (address word 03), with one or more additional DTCs. Scenario C is the messages "TPMS" and "Tire pressure: System malfunction!" appear while the vehicle is being driven. DTC 03159 (tire pressure monitoring in ESP function) is stored in the ABS control module, J104 (address word 03), without other DTCs.
A911446 2033313-
Supersedes Technical Service Bulletin Group 96 number 13-54 dated March 15, 2013. Adaptive Cruise Control (ACC) does not work. Adaptive Cruise Control (ACC) does not work. The message "ACC no sensor vision" appears in the cluster. DTCs are logged in the distance regulation control module, J428 (13). Adaptive Cruise Control (ACC) is deactivated when the radar sensor does not see any objects for an extended period of time (varies based on environmental conditions). The most common cause for this type of deactivation is that the field of vision of the radar sensor is blocked.
A191450 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
Edition89
ElsaPro Software update and technical bulletins
2014 Audi Tire C
This document contians the Audi tire chain information for all MY 2014 vehicles.
37 13 07 2033658
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
00146320335762
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
2037307/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 14 30 2003658
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37143020036586
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A001463 2033576-
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A011478 2037307-
The MIL is on. DTC P013E00 (O2 Sensor Bank 1 Sensor 2 Delayed Response - Rich to Lean) is stored in the engine control module (ECM), J623 (address word 01). ECM software needs to be updated.
A371430 2003658-
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
441450202256310
Steering wheel shimmy, vibration, and/or oscillation
A441450 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.
Update91i8
Google Maps Street View (NVLW))
A741419 2036572-
Supersedes Technical Service Bulletin Group 74 number 14-18 dated February 26, 2014. The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damaged is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is moved back far enough to make contact with the rear seat headrest.
2037159/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941440 2037159-
There is a mirror turn signal warning displayed in the driver information system. The turn signal inside of the mirror housing may be inoperative. No signs of physical damage can be seen on the mirror turn signal, cap, base, or glass. DTCs may be present. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts.
39141420289023
Squealing, howling, or whistling noise from under vehicle when cold
A391414 2028902-
Supersedes Technical Service Bulletin Group 39 number 12-12 dated June 12, 2012. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
A641433 2029714-
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required.
371422202898511
Transmission warning message in cluster (P074100 stored in TCM)
A371422 2028985-
Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
A911441 2035919-
Supersedes Technical Service Bulletin Group 91 number 13-17 dated December 3, 2013. The vehicle is a model year 2013 vehicle and TSB 2036607: 91 MMI3G+ Navigation GPS Location is inaccurate, has been completed. The GPS location or vehicle direction indicated on the navigation map does not match the vehicle's actual location or direction of travel.
27 14 24 2025360
Low battery charge: Diagnosis tips and TAC instructions
A271424 2025360-
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.
Edition83
97 no start
A911438 2033780-
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface.
Edition82
91 Generation III radio: Loose or broken control knobs
44144920225639
Steering wheel shimmy, vibration, and/or oscillation
A441449 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
97144320367643
97 No start (DTC P068A00)
A971443 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition81
Elsa newsletter
2036991/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4214202036991
Noise from rear suspension - Repair Authorization
42142020369911
Noise from rear suspension - Repair Authorization
A421420 2036991-
Customer hears squeaking, clunking, or rattling noises from the rear of the vehicle when it is driven over bumps. This condition may also be identified at PDI. The rear buffer stop may be out of place or require lubrication. In an effort to gain information regarding this condition, we request that you contact the Technical Assistance Center (TAC) before performing any repairs.
A911436 2027903-
Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected.
A911437 2030947-
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
2026895/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911430 2017425-
Supersedes Technical Service Bulletin Group 91 number 10-08 dated March 18, 2010. On generation III Concert and Symphony radios , the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence.
Edition80
Elsa newsletter
144920284402
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
87D9UPDATE
AC Pressure/Temperature Sensor (NVLW)
A171449 2028440-
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Edition75
Technical bulletins and updates
Dealer Letter -
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off.
Update87D9
AC Pressure/Temperature Sensor
920143
The Audi 2.0L Third Generation TDI Engine
97144220367642
97 No Styart (DTC P068A00)
A691428 2023323-
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.
A971442 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition79
Technical bulletins and updates
46147620341817
Brake noise analysis and handling
A461476 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-68 dated February 3, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
143220350734
The NVLD pressure switch may erroneously detect a very small leak.
A201432 2035073-
upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911429 2026888-
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
A971441 2036764-
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition77
Technical bulletins and updates
97144120367641
97 No start (DTC P068A00)
A911428 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
96148220363441
96 Alarm sounds when driver door is unlocked with mechanical key
A911427 2036575-
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered.
A961482 2036344-
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.
A871447 2010146-
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A741418 2036572-
The panel on the back of the front seat is warped or dented. The headrest on the rear seatback may also be damaged. The damage is caused when the headrest of the rear seat backrest comes in contact with the back of the front seat. This occurs when the rear seat is folded down with the headrests installed, and the front seat is moved back far enough to make contact with the rear seat headrest.
A851420 2033596-
Supersedes Technical Service Bulletin Group 85 number 13-17 dated May 15, 2013. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Improper operation of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower.
A911426 2036576-
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
Edition74
Diagnostics and updates
00145920297372
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
A001459 2029737-
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Edition73
Technical bulletins and updates
Edition72
Windows XP- End of Support (EOS) and new VAS diagnostic services
TSB-45-13-07
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. *PE UPDATED 05/21/2014 *JS
46146820341816
Brake noise analysis and handling
A461468 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-67 dated January 21, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. This TSB should not be used if another brake noise TSB is available for the vehicle. For additional helpful information, refer to the Audi Brake Systems brochure.
Edition71
Technical bulletins and updates
01146320336302
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
2033630/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011463 2033630-
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
TSB-01-14-63
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2008-2015 A3, A4, ALLROAD, TT, A5, A5 CABRIOLET, Q5, A6. *PE
A911424 2020399-
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.
A941432 2017806-
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.
44144720302757
Alignment - Repair Authorization
A441447 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. If the condition is due to outside influence (such as an accident), this TSB does not apply. In an effort to gain information on this condition, Audi of America is asking you to contact the Audi Technical Assistance Center (TAC) before you perform any repairs.
A461467 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-64 dated January 2, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
Edition69
Technical bulletins and updates
Edition68
Updates and suggestions
24AD
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24ADUPDATEa
ECM Software Update (FED_EMS)
143120350733
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two components): part numbers 8K0906253 and 8K0906253B supersede to 8K0906253D. ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, which are integrated (one component): part numbers 8K0906253A and 8K0906253C supersede to 8K0906253E.
2035073/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201431 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A461466 2022584-
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
A911419 2026895-
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
A461464 2034181-
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
2014 MY Schedule
Maintenance.
MY 2014 Audi Nor
Tire Pressure Table.
REV11142013
Tire Pressure Table.
PDI-2014 ALL MOD
This document contains the Audi vehicle condition checklist. This document is in Spanish.
PDI-2014 A5 Coup
This document contains the Audi delivery report checklist. This document is in Spanish.
PDI-2014 A6 DELI
This document contains the Audi delivery report checklist. This document is in Spanish.
A481356 2036032-
The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.
TSB-48-13-56
AUDI: WHEN VEHICLE IS STATIONARY, THE STEERING WILL FEEL STILL WHEN TURNING AND THE STEERING SHAFT NEEDS TO BE UPDATED WITH IMPROVED INTERMEDIATE STEERING SHAFT. MODEL 2009-2014 A4, A5, A5 CAB, Q5. *PE
Reference-Audi M
This document contains the Audi normal load condition tire pressure table. This document is in Spanish.
44134620103345
Tightening wheel bolts
A441346 2010334-
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
Edition65
Audi Elsa Newsletter
TSB-44-13-46
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
2035047/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137920350473
Lane Change Assistant "Sensors Blocked" warning in DIS (DTC C1114F3 and C1115F5)
A461363 2034181-
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A961379 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-77 dated September 23, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes.The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. DTCs are stored in the Lane Change Assistance control module. Audi Lane Change Assistant can be activated without issue. No obstructions can be found on the outside or inside of bumper. No re-work of the bumper can be found. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found on the inside or on the outside rear bumper area. The control module mounting brackets are not broken or loose. In certain normal driving conditions, the Audi Side Assist system can automatically deactivate, and the driver information display shows the "sensors blocked" message. This is normal, as the nature of certain driving conditions can make it difficult for the Audi Side Assist system to track vehicles.
2035919/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
40133720358541
Rattling/knocking noise from front end over bumps
A911317 2035919-
GPS inaccuracies can be caused by several different factors. If it is unclear if this PSS applies, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket. Customer states the navigation system is not tracking the vehicle correctly. No DTCs related to the GPS antenna or MMI system are present. The issue occurs after the vehicle is parked overnight or for several hours in a parking garage or other similar enclosed space. A private home garage does not apply. The issue does not occur if the vehicle is parked overnight or for several hours in an open-sky environment. The condition continues for the duration of the drive. The issue only corrects itself with a 3-finger reset or during a vehicle sleep cycle. The vehicle is not a Q7 or A8. If the above conditions apply and the customer vehicle is a Q7 or A8, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket.
9013422035902 1
90 "Ignition lock faulty" message in cluster information display.
A901342 2035902-
Ignition lock faulty message is displayed in the driver information display with the symbol shown at right. DTCs are stored in the comfort system central control unit. The "ignition lock faulty" message can be triggered by many different DTC entries. Presence of the message does not indicate that the ignition switch is faulty; the message typically has a different root cause. Replacing the ignition switch before completing GFF test plans typically does not correct the condition.
7013352022773 5
Components on the doors or the parcel shelf vibrate while heavy bass audio is played.
A701335 2022773-
Supersedes Technical Service Bulletin Group 57 number 12-70 dated September 5, 2012. Vibration noises from the doors or the rear parcel shelf are heard, particularly when heavy bass audio is playing. Components on the doors or the parcel shelf vibrate while heavy bass audio is played.
2035814/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
7413162035814 1
74 Front center armrest is stuck, does not slide, or is inoperative.
A741316 2035814-
The armrest will not operate in any direction. The height adjustment of the armrest will not engage or remain in position, or may become stuck in one position during height adjustment. If the armrest slides past its limit and the rods are pulled out of the armrest , it is because the retention of the bracket is insufficient. The armrest bracket is under tension because the guide plate has fallen loose from the bracket or the return spring has slipped from its original position.
Audi Newsletter
Elso pro reminder.
4413442022563 8
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
44134420225638
Steering wheel shimmy, vibration and/or oscillation
A441344 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
132820350732
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel tank cools off. If the natural vacuum leak detection (NVLD) system cannot detect this natural vacuum during the system self-test, the DTC will be stored in the ECM.
2013282035073 2
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel ank cools off. If the natural vacuum leak detection (NVLD)
A201328 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-27 dated October 16, 2013. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
Normal Load Cond
This document contains the Audi normal load condition tire pressure table.
TableA
Tabla de presión de los neumáticos de condición de carga normal para Audi modelo 2014
2035797/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
5513332035797 1
The customer complains of hearing a creaking or knocking noise.
A551333 2035797-
The customer complains of hearing a creaking or knocking noise from the front of the vehicle when the vehicle is twisted, such as when being driven into or out of a driveway. The customer may describe the location of the noise source as the front suspension area. This type of noise may be caused by the contact between the hood height adjustment stop buffers and the lock carrier. While noises originating from the front of the vehicle may have a number of causes, the repair described below will eliminate this possible cause.
Edition61
Audi Elsa Newsletter
134720354632
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.
A171347 2035463-
Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
9113142013790 8
The navigation DVD or other CD/DVD cannot be ejected.
A911314 2013790-
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
Tire pressure Ta
2014 Audi Normal Load Condition Tire Pressure Table.
QRSB-2014 Audi A
This document contains the quick reference specification book.
A571397 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
01133920353482
Under extreme driving conditions with the A/C compressor switched off (e.g., long idle periods or extended stop-and-go traffic), high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored. Coolant temperature above 102?C in the freeze frame data can be an indicator of those extreme driving conditions.
2035348/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011339 2035348-
Supersedes Technical Service Bulletin Group 01 number 13-31 dated September 25, 2013. MIL on. Customer may report loss of performance. DTC P008700 (fuel rail pressure too low) may be stored in the engine control module, J623 (address word 01). Under extreme driving conditions with the A/C compressor switched off (e.g., long idle periods or extended stop-and-go traffic), high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored. Coolant temperature above 102?C in the freeze frame data can be an indicator of those extreme driving conditions.
Reference-2014 N
This document contains the Audi normal load condition tire pressure table.
Reference-Oil Ca
This document contains the Audi oil capacity chart.
Table
Audi Normal Load Condition Tire Pressure Table
134420354631
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan.
A171344 2035463-
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
10212013
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A691326 2023323-
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed.
A871346 2035582-
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Edition58
Audi Elsa Newsletter
Update24AD
ECM Software Update
PDId
Lineamientos de entrega de Audi
PDIe
Informe del técnico de Audi
132720350731
EVAP System Leak Detected NVLD (very small leak))
A201327 2035073-
MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
27 13 19 2029010
Low battery charge: excess current draw location
A271319 2029010-
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
27 13 18 2023282
Battery testing and charging - vehicles with BDM
A271318 2023282-
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
741312 2004327-4
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Chart
Audi Oil Capacity Chart
GuidelinesL
Audi delivery guidelines
PDI - 2014 A5-S5
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
PDI - 2014 All M
This document contains the Audi vehicle condition report checklist.
ReportB
Technician report
ReportF
Vehicle detail report
ReportG
Vehicle condition report
A511307 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing.
48K8UPDATE
Power Steering Control Unit Software (NVLW)
A441342 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
01133120353481
Under extreme driving conditions with the A/C compressor switched off, high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored.
2033412/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2035348/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
45130720334122
ABS warning light on with additional warning lights on (EPB/TPMS/EPC/MIL) - Wire harness damage
A011331 2035348-
MIL on. Customer may report loss of performance. DTC P008700 (fuel rail pressure too low) may be stored in the engine control module, J623 (address word 01). Under extreme driving conditions with the A/C compressor switched off (e.g., long idle periods or extended stop-and-go traffic), high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored. Coolant temperature above 102?C in the freeze frame data can be an indicator of those extreme driving conditions.
A451307 2033412-
Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
A571394 2035367-
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
A721309 2035357-
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
2035047/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137720350472
Lane Change Assistant "Sensors Blocked" warning in DIS (DTC C1114F3 and C1115F5)
A901341 2010353-
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
A961377 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-72 dated August 26, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slowmoving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair.
A911308 2028190-
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.
Edition53
Audi Elsa Newsletter
A481354 2028220-
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
A801305 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A911304 2013422-
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A871345 2024644-
Supersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.
A101310 2018288-
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
44134020277795
Steering rack control unit cannot be coded
A441340 2027779-
Supersedes Technical Service Bulletin Group 48 number 12-33 dated October 22, 2012. After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual. All new replacement power steering control units (J500) must be coded and parameterized using online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then the SVM code is required to code and parameterize the new replacement control unit. The SVM code can be found in Parts Bulletin 9-97, which is available online through ETKA.
Audi A5 S5
Quick reference specification book.
ReferenceA
Quick Reference Specification Book
A911302 2018187-
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A961372 2035047-
Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair. The software of the Lane Change Assistance control module can deactivate the Audi Side Assist system in certain normal driving conditions because the nature of these driving conditions make it difficult for the Audi Side Assist system to track vehicles.
TSB-48-K-8
AUDI: UPDATED INFORMATION ON POWER STEERING CONTROL UNIT SOFTWARE, IN SOME VEHICLES, WITH ELECTROMECHANICAL POWER STEERING, HAVING SLIGHT IRREGULARITIES, MANUFACTURED A SPECIFIC PERIOD, MAINLY OCCURS WHEN TEMPERATURE IS AT FREEZING POINT. MODEL 2012-2014 A4, A5, Q5, A6, A7. *PE
A261319 2027945-
Supersedes Technical Service Bulletin Group 26 number 13-18 dated May 22, 2013. Humming or metallic rattling noise from under the vehicle, heard most consistently during engine idle or slow acceleration. Initial inspection indicates that the noise is coming from the exhaust system. Relative movements in the rear mounting of the exhaust system (rear silencer).
A461356 2034181-
Supersedes Technical Service Bulletin Group 46 number 13-53 dated August 7, 2013. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A641329 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Dealer Letter-Up
This communication is to inform you of a revision to Update 24Z6. The revision is in regards to the manifold actuator.
A511306 2009967-
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing.
2013_06_ATU Anal
This document contains information on analyzing squeaking windows on frameless doors.
2013_06_ATU Audi
This document contains information on the Audi side assist update.
A571392 2022032-
Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).
A911396 2026390-
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.
Edition46
Audi Elsa Newsletter
2034733/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137120347331
Radio station or Media track information does not show in cluster DIS - Gen 3 Concert Radio
A961371 2034733-
The customer complains that after the vehicle is started, the name of the current radio station or media track is not shown in the driver information system (DIS). After the music input is changed to a different source and then changed back (i.e., media to radio to media or radio to media to radio), the radio station or media track information is shown in the DIS.
37 13 09 2028715
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
37130920287152
Rough gear changes both when accelerating and slowing down
A371309 2028715-
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
TSB-37-13-09
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE
A911392 2030947-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.
44133920302756
Alignment - Repair Authorization
A441339 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.
A441338 2034445-
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. The "TPMS" message is not related to a loss of tire pressure. The message only indicates that tire pressure monitoring system (TPMS) is not active.
A961367 2019260-
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
PDI - 2014 A5 Ch
This document contains the Audi delivery guidelines checklist.
A461347 2034387-
Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.
A911388 2021780-
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected.
Edition42
Audi Elsa Newsletter
PDI - 2014 A5 S5
This document contains the Audi pre-delivery checklist.
01130920147538
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more conditions.
A011309 2014753-
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A191341 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A911387 2024683-
Supersedes Technical Service Bulletin Group 91 number 10-68 dated October 26, 2010. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.
30 13 18 2028229
Vehicle does not start or only starts when the clutch pedal is pressed very firmly
A301318 2028229-
Supersedes Technical Service Bulletin Group 30 number 11-11 dated December 9, 2011. Customer may report that the vehicle does not start or only starts when the clutch pedal is pressed very firmly. The message ?Press clutch pedal to start vehicle? may appear in the instrument cluster. There may be clutch mechanism wear.
AWC-13-08
Audi is committed to enhancing the Initial Quality Experience for our Customers within the first days of vehicle ownership. We want to resolve any knowledge or technical concerns a customer may have about a new vehicle, and build a strong, positive, enduring relationship between dealer and customer. To support this commitment to both our dealers and our customers, Audi is introducing the Audi Second Delivery Program for MY2013 and MY2014 vehicles. The Program is applicable to all new MY2013 and MY2014 vehicles and includes a one-time reimbursement per VIN of $75. The Second Delivery may be performed at the dealership or a location of the customer?s choosing.
Edition39
Audi Elsa Newsletter
A661330 2030471-
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Edition38
Audi Elsa Newsletter
GuidelinesJ
Audi delivery guidelines
GuidelinesK
Audi delivery guidelines
37-13-07
AUDI: SOME VEHICLES MAY LACK POWER OR WILL NOT MOVE AFTER STOP DUE TO SIMULTANEOUSLY DEPRESSING THE BRAKE AND ACCELERATOR PEDALS. *JS
94-13-19
AUDI: THE VEHICLE LIGHTS MALFUNCTION MESSAGE MAY BE DISPLAYED ON THE DASHBOARD CLUSTER. THERE IS NO FAILURE. ALSO INCLUDED MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL S7 MY 2012-2014, MODEL RS7 MY 2014. *JS
2027945/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 13 18 2027945
Humming or metallic rattling noise from under the vehicle, heard most consistently during engine idle or slow acceleration. Initial inspection indicates that the noise is coming from the exhaust system. Relative movements in the rear mounting of the exhaust system (rear silencer).
00134920335761
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
57-13-89
AUDI: SOME VEHICLES, IN COLD WEATHER, OCCASIONALLY, CANNOT BE UNLOCKED USING THE DOOR HANDLE TOUCH SENSOR. ALSO INCLDED ARE MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL RS5 CABRIOLET MY 2014, AND MODEL S5 CABRIOLET MY 2011-2014. *JS
A001349 2033576-
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
37 14 22 2028985
The fault occurs with ATF temperature below 60° C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
28 13 21 2017555
Key does not stay or engage in ignition lock
A281321 2017555-
Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote keys are inoperable. The message "ignition lock faulty" may appear in the instrument cluster driver information display. DTC 00166 (Access/Start Authorization Switch -E415- Incorrect Signal) may be stored in Comfort System Central Control Module J393 (address word 46). It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position).
01138620336301
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
A011386 2033630-
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
A001348 2002047-
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
A941312 2017566-
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.
133820129135
Engine oil service - filter cartridge replacement. When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.
97133520334121
ABS warning light on - wire harness damage
A171338 2012913-
Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement.
A971335 2033412-
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
A191335 2025303-
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A571386 2027368-
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
IQS
Audi On Track ? IQS Newsletter
A571385 2017082-
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A571384 2024463-
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. High early warranty information related to inoperative remote keys necessitates this repair authorization. Through our combined efforts and cooperation, we will be able to raise the level of Audi quality and overall customer satisfaction.
4413362022563
Steering wheel shimmy, vibration and/or oscillation
44134220225637
Steering wheel shimmy, vibration and/or oscillation
A441336 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
A941306 2017806-
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.
SB-AOS-13-01
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A571382 2017082-
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A911374 2024323-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
44133520225635
Steering wheel shimmy, vibration and/or oscillation
PDIm
Informe del técnico de Audi
PDIn
Informe del técnico de Audi
1335201004313
Engine oils that meet Audi Oil Quality Standards.
MaintenanceB
2014 Scheduled Maintenance Intervals
Scheduled Mainte
This document contains the scheduled maintence intervals.
A901238 2032113-
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
24ADUPDATE
ECM Software Update (FED_EMS)
0112562031368
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module:
A011256 2031368-
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.