TSB_2074436_3
Service Bulletin/Repair Instructions
This bulletin provides information when the horn sound quality is poor.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB_2074436_3
This bulletin provides information when the horn sound quality is poor.
TSB_2068999_4
This TSB describes a corrosion issue due to outside influence and the prohibition of warranty in these cases.
TSB_2069078_4
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2069904_3
This bulletin provides information for all models regarding brake sounds.
TSB_2072304_4
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_20741717_15
This bulletin provides information on the GFF test plan required for AC compressor replacements regardless of the concern.
TSB_2075120_3
This bulletin provides information about the general approach for brake vibration concerns.
TSB_2079732_2
This bulletin provides information when there is a paint issue on alloy wheels.
TSB_2082846_1
This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.
SM 01-2026
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
TSB_2073282_1
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the dipped beam is switched on.
TSB_2034863_5
This bulletin provides infomraiotn when there is a gearbox malfunction message in the instrument clostuer; DTC P0706; vehicles with 0AW gearbox.
TSB_2082617_1
This bulletin provides information when there are noises in the overrun ( e.g. whirring, howling) - vehicles with 0BC.
TSB_2028902_5
This bulletin provides informaiton when the transmission warning message appears in the cluster; P074100 stored in the TCM.
TSB_2028985_13
This bulleitn procides informaiton when tehre is a transmission warning mssage in the instrument cluster; P074100 is stored in the TCM.
TSB_2059335_7
This bulletin provides information when there are noises from the area around the instrument cluster.
TSB_2074729_3
This bulletin provides informationwhen noises/vibration are detected from front of vehicle in dynamic mode.
TSB_2082323_1
This bulletin provides informaiton when the engine is not running smoothly, misfiring.
TSB_2052680_6
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
AOS-26-25
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.
TSB_2074808_4
The high-voltage batteries in electric vehicles are subject to various ageing effects which could lead to the energy content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years
TSB_2022032_12
This bulletin provides diagnostic information for the vehicle locking system.
TSB_2070568_6
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2081531_1
This Reporting obligation requests that technicians contact the Technical Assistance Center (TAC) when the diagnostic tester refers to this reportin gobligation or to TPI 2033392.
TSB_2081409_1
This bulletin provides informaiton regarding the Universal Traffic Recorder.
TSB_2023187_8
This bulletin provides informaiotn regarding squeaking noises when steering or maneuvering.
TSB_2081405_1
This bulletin provides informaiotn about various infortainment system complaints.
TSB_2024323_13
This bulletin provides information when the parking assistance gives false warnings.
DC_Audi_CF_ Airbag
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent warning regarding counterfeit replacement airbag inflators that are being installed in used vehicles.
TSB_2024323_12
This bulletin provides information when the parking assistance gives false warnings.
TSB_2021205_10
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2059335_6
This TSB provides information when there are noises from the area around the instrument cluster.
TSB_2052680_4
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
TSB_2080329_1
This bulletin provides informaiotn when there are noises from the headliner.
TSB_2080681_1
This bulletin provides information regarding contact checks for event memories, intermittent.
TSB_2060750_5
This bulletin provides information regarding UV leak additive for finding oil leaks.
TSB_2074846_4
This bulletin provides information about vibrations and rotational steering vibrations.
TSB_2056019_5
This bulletin provides information when the anti-theft alarm activates for no reason, or does not activate.
TSB_2061669_3
This bulletin provides service infrmation for workshop mode with Audi connect vehicles.
TSB_2021205_9
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2074808_3
This bulletin provides additoinal information to assist in determining the energy content of lithium-ion high-voltage batteries.
TSB_2018187_18
This bulletin provides information when there are speaker rattles, vibrations, or audio interference.
TSB_2080186_1
This bulletin provides information when the MIL is on, DTC P310B00 in ECM; Vapor pocket formation in fuel system.
TSB_2069904_2
This bulletin provides information for all models regarding brake sounds.
TSB_2069078_3
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2075120_2
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
TSB_2030471_8
This bulletin provides informaiton when the license plate mouting bracket threaded inserts are stripped.
TSB_2056386_11
This bulletin provides information about the steering wheel alignment.
TSB_2072304_3
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2074846_3
This TSB provides information regarding rotational and other steerihng wheel vibrations.
TSB_2079732_1
This bulletin provides information when tehre is a paint issue on alloy wheels.
TSB_2047812_8
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator decomissioned).
TSB_2073917_2
This bulletin provides information for when there is a fluid sample request from Product Support.
TSB_2076605_2
This TSB provides informaiton pertaining to noises from the guide link bush.
TSB_2071264_2
This bulleitn provides information whent here are complaints about route guidance with Navigation.
TSB_2041717_14
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of the concern.
TSB_2042920_3
This bulletin provides information when there is corrosion on the tailpipes.
TSB_2070568_5
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2074436_2
This bulletin provides information when the horn sound quality is poor.
AOS-25-47
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
TSB_2060750_4
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
TSB_2027368_7
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
TSB_2010353_6
This TSB provides informatin when the cigarette lighter element does not eject, or the cigarette lighter is inoperable.
TSB_2070568_4
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2042920_2
This bulletin provides information when there is corrosion on the exhaust tail pipes.
TSB_2056019_4
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
TSB_2077320_2
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2031473_6
This service information TSB describes a cosmetic issue after using a car wash.
TSB_2071893_2
This TSB provides damage assessment guidelines for textile seat covers.
Circular_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
Dealer_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
TSB_2077320_1
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2075530_2
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
TSB_2041717_13
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the concern.
TSB_2071185_2
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
TSB-2076945_1
This bulletin provides information about leather care and seat repair.
A6625162049680_3
This TSB provides information when the exterior rubber trim is spotted.
A4025932076605_1
This TSB provides informaiton pertaining to noises from the guide link bush.
A3725312074822_2
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
A5124322068999_3
This TSB provides information when there is cracked paintwork with corrosion at joint between roof and roof side member.
A8724952041717_12
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
A6624152046229_5
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
A2724842074729_2
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic mode.
A4424092056386_10
This bulletin provides information regarding wheel alignment.
A0124482014753_13
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
A9124872024323_11
This TSB Provides information when parking assistance provides false warnings.
A9124842018187_17
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
A0024992070568_3
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
A9324342074808_2
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A9624072056019_3
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
A5724652022032_11
This bulletin provides diagnostic information regarding the locking system.
A1524532075530_1
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
CampTip_RNA_Audi
Vehicle Concerns Before Recall Repair Available
A2424632074810_2
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is working; mileage below 50 km/32 miles.
A8724892041717_11
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless of the concern.
A0024932002047_13
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical Assistnce Center (TAC).
A4424082074846_2
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
A5124312068999_2
This bulletin provides information when there is visible corrosion at the joint between the roof and roof side member.
A0024922031473_5
This bulletin provides informationw hen there are car was brush bristles trapped in the seam between the headlight and fender.
A4324982075100_1
This bulletin provides information on repairs on the air spring strut of the frong axle; additional sealing.
A4524462072304_2
This bulleitn provides information when there is an implausible signal in the ABS/ESC speed sensor.
A4524492075120_1
This bulletin provides information regarding the general approach to brakes rubbing.
A4624592069078_2
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic brakes.
A3924722059129_6
This bulletin provides information when there are noises and/or vibration in tight turns in vehicles with quattro drive.
A0124342074976_1
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in petrol.
A9124432074929_1
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
A9324042074808_1
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A0024902074853_1
This bulletin provides service information ror when the fuel tank cannot be fully filled.
A3724222074826_1
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
A4424062074846_1
This bulletin provides information vibrations and rotational steering wheel vibrations.
A2424612074810_1
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not working; mileage below 50 km/32 miles.
A2724762074729_1
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
A3724132074750_1
This bulletin provides information about replacing the clutch end cover.
A3724142074751_1
This bulletin provides information about replacing the clutch end cover.
A3724212074822_1
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
A9124322018187_16
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
A8224002041717_10
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
A0024872002047_12
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center (TAC).
A9124252018187_15
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
A9424822074347_1
This bulletin provides informationw hen there are optical concerns with the tail lights.
DC_Q5 Hybrid
This document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday, June 24.
A9124162018187_14
This bulletin provides information when there are speaker rattles, vibration or audio interference.
A5724432027368_5
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
A9424812073332_3
This bulletin provides information when there is noise while steering.
A5724422025031_3
This bulletin provides information when the exterior trunk handle is inoperative.
AWA 24-04
Diagnosed and confirmed malfunction of the vehicle’s AEB system that resulted from failure or malfunction of the AEB system’s control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.
A1124002073917_1
This bulletin provides information for when there is a fluid sample request from Product Support.
A0024852021205_8
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
A872474202012414
This bulletin provides information when the air conditioning is no longer operative; DTC 00457, 00256, 01592.
A9024842032113_9
This bulletin provides general information regarding outside air temperature readings.
A9624962027416_7
This bulletin provides information when the sunglass holder will not close or is stuck closed.
A9024832059335_5
This bulletin provides information when there is noise from around the instrument cluster.
A9424762073332_2
This bulletin provides information for when there is noise when steering.
A2724712067906_5
This bulletin provides information for when DTC P0A7D00 is stored.
A5724342017082_1
This bulletin provides information when the remote control key is inoperative.
A0024842073507_1
This bulletin provides instructions on evaluating TDI vehicles for repurchase prior to repairs.
A9624952073471_1
This bulletin provides information when various driver assistance systems are unavailable - DTC C110702, B201200.
A9424742073332_1
This bulletin provides information if there is noise when steering the vehicle.
A9424722073282_1
This bulletin provides information on visual concerns with the headlight lens.
A4824612034351_1
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
AWA 24-01
This Document informs dealers on the new oil consumption & piston fracture warranty extension for 2012 A4, A5, A6, Q5 & TT / 2013 A4, A5, A6, Q5 & TT / 2014 A4, A5, A6, Q5 & TT / 2016 A3 & TT / 2017 A3 & TT vehicles
A9124632044694_3
This bulletin provides information pertaining to MMI Navigation database concerns.
A6824452038904_2
This bulletin provides information when the power outlet compartment is detached from the center console.
DC_Closure 19N8
SERV_ACT - After-Run Coolant Pump - Closure Notice
A0023822047812_7
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via the Mirror Server.
A912306202432310
This bulletin provides information when the parking assistance provides false warnings.
A4523362072304_1
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
A9023562032113_8
This bulletin provides general information about the outside air temperature reading.
A6623042030471_7
This bulletin provides information for when the license plate mounting bracket threaded inserts are stripped.
A0023812070568_2
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
A9423672071954_1
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
A7423262071893_1
This bulletin provides damage assessment guidelines for textile seat covers.
A0023762071721_1
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans (Ghost faults).
A0123812028842_4
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
A0023742052680_4
This bulletin provides information on the additional reporting requirements for safety related inquiries.
A0023732061669_2
This bulletin provides information on workshop mode with Audi connect vehicles.
A0023712070568_1
This bulletin provides information on professional noise analysis with the VAS 611 015 PICO NVH Tool.
A9123262071264_1
This bulletin provides information for when the customer has concerns about the navigation route guidance.
A6423922020552_1
This bulletin provides information for when exterior glass cleaning is needed.
A8723452041717_9
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
A9023322059335_4
This bulletin provides information for when there is noise from the area around the instrument cluster.
A922336203815115
This bulletin provides information for when the washer solvent level warning is on.
A4623452070679_1
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29.
A4823412028220_1
This bulletin provides information for instances where the steering wheel leather is damaged.
A102326201828810
This bulletin provides information on checking for debris when replacing an engine.
A9423652061922_3
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and taillights.
A5723082027406_5
This bulletin provides information regarding the Audi advanced key.
A922335203815114
This bulletin provides instructions for when the washer level warning is on but the reservoir is full.
A0023702021205_7
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
A0023692031473_4
This bulletin provides information for when car wash bristles become stuck in the body gap between the headlight and fender.
A912394201818713
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference.
A9423632061922_2
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty submissions.
A4423992056386_9
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4423982056386_8
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4623432069904_1
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
A9023222032113_7
This information bulletin contains a background on the outside air temperature reading.
A192336202530314
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
A6423882047061_5
This bulletin describes the process to clean sticker residue from the windshield.
A4023512023187_7
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and repair is not needed.
A402352202431813
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9123832037809_1
This bulletin provides information on how to update the navigation map.
A9623822056019_2
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored.
A462341203418123
This bulletin provides instructions for brake noise analysis and handling.
A012341201475312
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A9223332038151
This bulletin provides instructions for when the washer solvent level warning is on in the DIS but the washer solvent level is correct.
DC_Alternator_6
Support for Customers Affected by Alternator Back-order
A6423862047061_4
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production.
A6623942049680_2
This bulletin provides instructions for when the exterior trim has spots.
A4423972022563_2
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph.
DC_Alternator_4
Support for Customers Affected by Alternator Back-order
DC_Alternator_5
Support for Customers Affected by Alternator Back-order
A8023122062583_2
This bulletin provides instructions for when the customer advises that there is insufficient or uneven cabin heating from the HVAC system.
DC_Alternator_3
Support for Customers Affected by Alternator Back-order
A9123592036576_7
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s).
A4623402069078_1
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
A5123262068999_1
This bulletin provides instruction for when a customer advises that a visible line of corrosion is forming in the roof.
DC_Alternator_2
Support for Customers Affected by Alternator Back-order
DC_Alternator
Support for Customers Affected by Alternator Back-order
DC_RECALLS
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
A572200202203210
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A1922332061604_5
This bulletin contains instructions for resolving a coolant leak.
DC_TDIReminder
TDI Reminder message
DC_TDI_repairs
Dealer Communication: IMPORTANT: Evaluate TDI Vehicles for Repurchase Prior to Repairs
A0022582045316_6
This bulletin contains information for diagnosing the Start/Stop system.
A462234203418122
This technical service bulletin provides troubleshooting for brake noise.
A4822342065978_2
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly.
A922230203815112
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A642285202055211
This bulletin provides instructions on how to properly clean exterior glass.
SM 48-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4622332051095_7
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462232203418121
This technical service bulletin provides troubleshooting for brake noise.
SM 47-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4522262067132_1
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs.
A442292202256321
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A8722272041717_8
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A872225201014617
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation system.
A402238202431812
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
A9022572032113_6
This is an informational bulletin containing information about the outside temperature reading.
A9022582059335_3
This bulletin contains information on noises from the instrument cluster installation area.
A462230203418120
This technical service bulletin provides troubleshooting for brake noise.
A402237202431811
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
DC_20220329
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
A172219204064413
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A172218204064412
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A1722172060750_3
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A4622282051095_5
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A012216203300126
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9122752024323_9
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A442287202256320
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A462226202258411
This informational bulletin provides diagnostic information for brake conditions.
A462227203418119
This technical service bulletin provides troubleshooting for brake noise.
A6922792065962_1
This bulletin advises on identifying when a foreign object has obstructed normal operation of the seat belt.
A192228202530313
This bulletin contains instructions for identifying and mixing factory fill coolants.
A192227202530312
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4421862056386_7
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4021302023187_6
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or maneuvered.
A4021312024318_1
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A002155201173212
This bulletin contains general instructions for software updates.
A4421842065160_1
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
DC 20210928
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
A9121342018187_1
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A012111203300125
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A8721162041717_7
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A0121102028842_3
This informational bulletin gives instructions for identifying chip tuning.
A4821092028220_9
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty.
A4421832056386_6
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
148520367612
The oil pressure switch is defective.
A1921222046712_3
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A2021352043357_1
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A0021482021205_6
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
A0021472031473_3
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again.
A4821052063527_1
This bulletin contains instructions for calibrating the steering angel sender G85.
SM 44-2021
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
AWA 21-03
This Document informs dealers on the new electromechanical steering unit warranty extension for 2012-2015 Model Year Audi B8 (A4, Q5 & SQ5) and C7 (A6) Vehicles
147920333793
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced.
A1921182061604_4
This bulletin contains instructions for resolving a coolant leak.
A9121042024323_8
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0021442052680_3
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage).
A1021222018288_9
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
A9021032058077_5
This bulletin contains instructions for determining unexpected Audi presense interventions.
A1721162060033_3
This bulletin contains repair instrructions for when there are noises in the engine compartment with DTC P052E00.
A4421822056386_5
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A6421802020552_1
This bulletin provides instructions on how to clean exterior glass.
A8721132010146_1
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
ELSAallignAudi
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
A9021002032113_5
This information bulletin contains a background on the outside air temperature reading.
AWA 21-04
This Document informs dealers on the new turbo warranty extension for 2013-2016 A4, 2013-2017 A5/Q5, and 2012-2015 A6 vehicles
A4021242016453_4
This bulletin contains instructions for determining if bushings need to be replaced.
A9021982059335_2
This bulletin contains information on noises from the instrument cluster installation area.
A6421792047061_3
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A1921152061604_3
This bulletin contains instructions for resolving a coolant leak.
A5721752022032_9
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A9121862062713_1
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
A8021112062583_1
This bulletin contains instructions for addressing an insufficient or uneven heating performance from the HVAC system.
A9421362023322_3
This informational bulletin contains information on the different shading of LED headlights.
A1321132062387_1
This bulletin contains instructions for determining if a repair is needed when coolant touches a poly V-belt and/or a toothed belt.
A1921142061604_2
This bulletin contains instructions for resolving a coolant leak.
A9121762037809_8
This informational bulletin contains instructions about updating the navigation map.
A4621252054385_2
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill).
A4421802056386_4
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4621222051095_4
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462123202258410
This informational bulletin provides diagnostic information for brake conditions.
A462124203418118
This technical service bulletin provides troubleshooting for brake noise.
A4421792022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A6621692030471_6
This informational bulletin covers the condition of when license plate mounting bracket threaded inserts are stripped.
A9421332061922_1
This informational contains instruction on how to document optical concerns for warranty claims.
A1721122060750_2
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A2321562059205_2
This bulletin contains information on when to submit a TAC ticket for DTC P220100 with various DFCC codes.
A9121642024323_7
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A5520512014055_8
This bulletin contains instructions for addressing discoloration due to moisture on a new vehicle.
A9120572036575_6
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
SM C-2020
This special notice is to inform dealers to return the part numbers listed (State of California only).
A5020042061716_1
This bulletin contains instructions for addressing a creaking noise in the floor.
A1920102061604_1
This bulletin contains instructions for resolving a coolant leak.
A0020432061669_1
This informational bulletin contains instructions for Audi connect before performing any MMI work.
2010-2021EngOil
Added Saga Part number for 0W40 oil: SAGA Part: G E55040S0
A012093203300124
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9120242026611_7
This bulletin contains a guide for troubleshooting HD radio issues.
A0020422045316_5
This bulletin contains information for diagnosing the Start/Stop system.
A9120152035912_4
This bulletin provides troubleshooting for an incorrectly coded Top View/Corner View Camera System.
A1720112060750_1
This bulletin contains instructions for using the UV additive to find engine oil leaks.
EmailAUTDI2L-3L
Reminders - TDI Approved Emissions Modifications, Emissions Compliant Repairs, corrections and extended warranty / warranty policy and loaner vehicle overview
21AUTIRECHAINS
Added new graphic to reflect where to find MY 21 information
A0120882033001_2
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9020652032113_4
This information bulletin contains a background on the outside air temperature reading.
A1720102060033_2
This bulletin contains repair instrructions for when there are noises in the engine compartment with DTC P052E00.
Audi Part Labels
Recall Reminder Part Labels
A1720072060033_1
This bulletin contains repair instructions for when there are noises in the engine compartment with DTC P052E00.
A1720082060259_1
This bulletin contains repair instructions for when DTC P052E00 is stored with noise coming from the engine compartment.
A012072203300122
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A3720012039650_2
This bulletin contains instructions for addressing a leak from the transmission oil pan gasket or transfer case.
A1720062028440_5
This informational bulletin explains when the range display is empty in the on-board computer.
A6420752058551_3
This bulletin contains repair instructions for when the window switch is malfunctioning by opening instead of closing as directed by customer input.
A1920042025303_1
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4320412059843_1
This bulletin contains a software update for an adaptive suspension warning with DTCs C104011, C104111, C104211, and C104311.
A9020512058077_4
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A0020382039206_3
This informational bulletin contains instructions on how to use the QR code in a TSB.
A9120732026390_7
This bulletin contains instructions for correcting the phonebook.
A9120702044694_2
This technical service bulletin provides troubleshooting for issues with the navigation map database.
A4020052024318_9
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9120652036576_6
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
A6420742020552_9
This bulletin provides instructions on how to clean exterior glass.
A012062203300121
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A0020372059437_1
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing some issues.
A872005201014615
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
A9020442032113_3
This information bulletin contains a background on the outside air temperature reading.
A9020452059335_1
This bulletin contains information on noises from the instrument cluster installation area.
SM 25-2020
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A0020362002047_1
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
A012058203300120
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A2320542059205_1
This bulletin contains information on when to submit a TAC ticket for DTC P220100 with various DFCC codes.
A6420722047061_2
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A012054201475311
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A6420702058551_2
This bulletin contains repair instructions for when the window switch is malfunctioning by opening instead of closing as directed by customer input.
A172099204064411
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A942020201780613
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A5120132009967_1
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A012046201475310
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A912039201818711
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
Circular19N8REV1
SERV_ACT - After-Run Coolant Pump - Updated claiming and work instructions: A single part number per criteria will now be used.
A4420732056386_3
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A9020372058077_3
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A9020362058077_2
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A921924203815111
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A0019292031473_2
This informational bulletin contains instructions for when car wash bristles are stuck in the headlights. 2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant
A9419182012749_1
Exterior lights, moisture accumulation 2013-2021 A3 Cabriolet, 2016-2018 Sportback, 2004-2005 A4 Cabriolet, 2004-2008 S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8
20AUTIRECHAINS
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
AWA 19-06
The communication contains the details of the water pump extended warranty.
A9219232038151_1
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct. 2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant
A4419712022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7
A9619452049284_2
This bulletin contains a software update for an intermittent error message for traffic sign recognitions or the active lane assist, DTC B2F0400.
145320381292
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A9119032041430_7
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A1919992052657_3
This informational bulletin contains details on conditions for replacing the water pump and/or thermostat housing. 2015-2019 A3 Cabriolet, 2017-2018 S3 Cabriolet, 2018-2019 A5 Sportback, S5 Sportback, 2013--2019 TTR
A4819822034351_9
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A4019972018194_9
This bulletin contains repair instructions for leaking shock absorbers.
A0019272045316_4
This bulletin contains information for diagnosing the Start/Stop system.
SM 80-2019
Parts are currently blocked from sale at this time.
A0019262052680_2
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage.
ATUBody2019
Body components - Examples of customer misuse
ATUChassis2019
Wheel change mode/jacking mode - Description and usage
A9119922041430_6
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A9119932037087_4
This bulletin contains instructions for enabling text message notifications through the MMI system.
A0019252011732_1
00 Software Version Management (SVM), operating instructions
A9419132017806_1
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A9119882024323_6
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0119252055816_2
This bulletin contains repair instructions for DTCs P007000 and P208000.
A1719982028440_4
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
A9619432056019_1
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off. Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
AWC 19-05
This communication is issued to inform dealers of updated shipping regulations related to lithium ion batteries.
Circular 26L9
Exhaust Gas Recirculation (EGR) Cooler
Dealer 26L9
Exhaust Gas Recirculation (EGR) CoolerÂ
Circular 23Z8
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Additionally, to reduce soot accumulation affecting the oxygen sensor, it is necessary to replace and relocate the sensor, which requires replacement of the diesel oxidation catalyst (DOC) and diesel particulate filter (DPF).
SM F-2019
The part number listed in the document are to be returned if it meets the criteria provided.
A0119212055816_1
This bulletin contains repair instructions for DTCs P007000 and P208000.
Dealer 23Z8
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Additionally, to reduce soot accumulation affecting the oxygen sensor, it is necessary to replace and relocate the sensor, which requires replacement of the diesel oxidation catalyst (DOC) and diesel particulate filter (DPF).
AWC 19-04
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8
A011919203300119
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A4819792028220_8
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe
A8719932044717_9
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
A2319512036668_5
This informational bulletin contains diagnosis instructions for the N290 fuel metering valve. TDI ONLY
A0019222047812_6
This informational bulletin contains instructions for setting up and using the SD Creator program. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A4619132039187_2
This bulletin contains repair instructions for DTCs C100E01, C100E12, C100D01, and C100D12 with an electromechanical parking brake warning light in the cluster.
A8719912041717_6
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A9019192032113_2
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe
A9119652050565_2
This bulletin contains general software update instructions for vehicles with PR Code 7UH. 2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster
A0019212052680_1
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe
A201918204335711
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A9119622038927_3
This bulletin contains repair instructions for when the overhead view camera system is not working and has various DTCs logged.
A9419082034735_3
This bulletin contains repair instructions for when the headlight has cracking present without being in an accident.
A201916203507314
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.
AWA 19-03
This bulletin explains the warranty extension for the crankcase ventilation valve on certain 3.0L and 4.0L vehicles.
AWA 19-02
This bulletin clarifies how to claim AdBlue on warranty claims.
Circular - 19N8
After-Run Coolant Pump
Dealer - 19N8
After-Run Coolant Pump repair available.
A201913203507313
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. Vehicles also include 2015 A3 Cabriolet and 2012 RS7,
A011913 20353688
This bulletin contains repair instructions for when a MIL is on with DTC P203B00.
A571954 20220328
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A961934 20489272
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A201911 2043357
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A011902 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A921916 2038151
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A441969 2022563
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A461903 2034181
This technical service bulletin provides troubleshooting for brake noise.
A701967 2044763
This technical service bulletin provides instructions for covering the trim of the head-up display to reduce a rattling noise.
A001915 2047812
This informational bulletin contains instructions for setting up and using the SD creator program.
19N4 19O2
This news email tells dealers when to perform 19N4 or 19O2
AWC 17-34
This communication instructs dealers to contact the Technical Assistance Center if they encounter a MIL on before performing the TDI emissions modification. - REVISED 12/17/18 to apply to 3.0L models and to remove 2.0L models.
AWC 18-14
This communication notifies dealers that AWC 17-34 was modified to remove 2.0L vehicles and apply to 3.0L vehicles only.
A011894 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A911821 2051527
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A011893 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A001814 2045316-
This bulletin contains information about the Start/Stop system.
TDI Repair and I
Email TDI Repair and IN-FORM Tool Enhancement
A461899 2040964-
This bulletin contains repair instructions for a brake squeal for light to moderate pressure.
Campaign Parts B
3.0L TDI Emissions Recalls 23R8 Part supersession
Communication 19
Communication Toolkit for Dealers
A011879 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
AWC-18-09
This communication provides instructions for documenting the fuel refill in the INFORM tool.
Email Audi TDI C
Email-Audi TDI-Customer Modificaion Amenities
AWC 18-07
This communication serves as a reminder that dealers are to check for pre-existing conditions for all Generations of 2.0L TDI and 3.0L TDI resale, buyback, TDI Direct, and VCI auction vehicles prior to proceeding with the AEM Emissions Recall. Only create an Audi Technical Assistance Center (TAC) ticket if required by applicable recall.
AWA-18-01 201806
This bulletin explains the extended emissions warranty for TDI vehicles modified under Campaign 23V4. The parts list was updated to include service numbers.
A011875 2035368-
This bulletin contains repair instructions for when a MIL is on with DTC P203B00.
A911800 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A911899 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
Email-Audi 3.0L
Dealer Communication: 3.0L TDI Trade-In Issue Resolution
Circular - Emiss
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Removed California DMV Tie-in Requirements
Emissions Recall
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Removed California DMV Tie-in Requirements
A911895
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
A911895 2026657-
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
Email-Audi AEM T
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement
A171893 2040644_
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A011862 2050329_
This bulletin contains repair instructions for when the MIL is on and there are one of several DTCs stored in the ECM.
Email-TDI Virtua
TDI Virtual Closing Resources
ATU_Chassis_Janu
EPB ?Driver absent application? function
Email-2.0L TDI a
2.0L TDI and 3.0L TDI Extended Emissions Warranty On-Board Diagnostic (OBD) System Coverage Questions
A011857 2042071_
This bulletin contains repair instructions for when the MIL is on and one of many DTCs is stored in relation to dylinder on demand function.
AWC-18-05
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles.
A871885 2044717_
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
Circular-Emissio
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Revised legal approved copy.
Email-AdBlue par
This email clarifies which part numbers dealers can use for refilling AdBlue.
Email-2.0L & 3.0
Email-2.0L & 3.0L TDI AEM ECR Replacement Labels
A011852 2050329_
This bulletin contains repair instructions for when the MIL is on and there are one of several DTCs stored in the ECM.
AWA-18-05
This communication provides coding instructions for AdBlue refills after the AEM is performed.
A911870 2041430_
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A971860 2036764_
This bulletin contains repair instructions for when the vehicle will not start and DTC P068A00 is stored.
AWC 18-04
This communication is a reminder to dealers that they must refill vehicle fuel tank after AEM.
A231745 2049856-
This bulletin contain repair instructions for the TDI emission modification.
Booklet - 3.0L T
3.0L TDI Gen 2-PC_Booklet
Customer Letter
3.0L TDI Gen 2-PC_Customer letter
E-mail 3.0L TDI
E-mail - 3.0L TDI Gen 2 Emissions Compliant Repair (ECR) Approval
A001706 2047812-
This informational bulletin contains instructions for setting up and using the SD creator program.
A8717842044717-6
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
A961721 2048927-
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A011748 2040403-
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored.
A171789 2040644
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A911760 2040406
This bulletin contains instructions on a repairing an issue when the GPS does not have the correct location or reception.
A001702 2035505
This repair authorization is for special VINs that are part of the Audi on Demand and Audi at Home program.
A961720 2049284
This bulletin contains a software update for an intermittent error message for traffic sign recognitions or the active lane assist, DTC B2F0400.
A871782 2044717-
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
A511711 2009967-
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A191790 2047114-
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501.
A911750 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
Maint Flip Chart
Revision to Tires-rotate: 5K only; added "(except R8)"
A911745 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
A911743 2042097-
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI navigation.
A201796 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A011732 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A001799 2045316-
This bulletin contains information about the Start/Stop system.
A011730 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A871781 2044717-
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
SM 52-2017
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation 14s.
e-mail - Audi 3.
3.0L TDI Trade-In Issue Resolution.
A201795 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A941791 2012749-
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
A911736 2024323-
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A201794 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201792 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401774 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A191789 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A401770 2018194-
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
A401768 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
Email - 2.0L and
2.0L & 3.0L TDI Settlement Updates
21F2 - Circular
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
SM 44-2017 EN
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward.
Email-3.0L TDI U
3.0L TDI Update - Claim Processing Appointments
A461772 2047830
This informational bulletin contains instructions for proper brake maintenance.
A201790 2043758
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401766 2024318
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A911732 2033355-
This informational bulletin contains information on why ACC sensor could be deactivated.
A941788 2039584-
This bulletin contains repair information when there is a bulb failure warning on one or more of the taillights.
e-mail 3.0L TDI
e-mail communication for 3.0L TDI Update - Claim Processing Appointments
21F2 - Bulletin
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
A001793 2047812-
This informational bulletin contains instructions for setting up and using the SD creator program.
A911730 2043595-
This bulletin contains software update instructions for incomplete text on the MMI screen.
A911731 2044670-
This bulletin contains instructions for a software update to correct an issue with dropped calls in RMC MMI systems.
A171784 2038119-
This bulletin details instructions on handling when the oil minimum message appears but the oil level is above minimum but not overfilled.
21F2 - Dealer Le
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
A481774 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A171783 2040644-
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A201789 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A441764 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A011715 2047785-
This is an informational bulletin requesting that dealers with the V6 TDI engine call TAC for instructions when they receive one of six DTCS in conjunction with DFCC symptom codes between 19184 and 19189.
A901777 2036132-
This bulletin contains software update instructions to correct a heads up display flicker or dims quickly.
A171782 2010043-
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil change.
A301722 2019850-
This technical service bulletin provides guidelines for diagnosing the clutch plate.
A011713 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A011712 2047707-
This informational bulletin provides instructions for when DTC P195000 appears but there is no customer concern.
A001791 2045316-
This bulletin contains information about the Start/Stop system.
E-mail-3.0L TDI
3.0L TDI Settlement Program Update
A421737 2038689-
This bulletin contains information on how to fix a clunking or rattling noise heard from the rear suspension when the vehicle id driven over bumps.
A911724 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
A401761 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A481772 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A571740 2047432-
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored.
A191785 2047114-
This bulletin contains repair information for a malfunctioning V50 coolant recirculation pump that prevents the passenger side from heating properly with DTC B10D004 or B11D501.
A231740 2036668-
This informational bulletin contains diagnosis instructions for the N290 fuel metering valve.
A901775 2030193-
This informational bulletin contains details about a normal function of the top view camera system.
A201788 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A571738 2017082-
This informational bulletin contains instructions for sychronizing the remote key after the battery has been disconnected or replaced.
Edition76
Technical bulletins and updates
A191779 2036852-
This informational bulletin provides a clarification on a normal operation for the cooling fans.
Bosch Class Acti
Bosch Class Action Communication - Audi
Updated Bosch Cl
Bosch Class Action Communication - Audi
ATE-17-05
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
Email - Audi 3.0
This is an email covering the 3.0L TDI terms of the settlement. It gives you links that cover FAQs avout the settlement.
A011703 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A171780 2040644-
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A011701 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
Bulletin - Updat
Update ECM software to improve diagnostic of NVLD system. Bulletin revised to update claiming instructions.
Bulletin-Dealer
Update ECM software to improve diagnostic of NVLD system.
A191777 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
AWA 17-02
This bulletin explains the terms of the bridge warranty being offered for affect 3.0L TDI vehicles.
A871780 2044717-
This bulletin provides instructions on correcting a high-pitched buzzing noise in the cabin when the fan speed is no higher than 2.
A201785 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A171779 2040644-
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A201784 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A911701 2044670-
This technical service bulletin provides instructions for a software update to correct an issue with dropped calls in RMC MMI systems.
A911700 2041430-
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
AWA1609
This is a general communication notifying dealers that there is extended Warranty coverage available for the exhaust gas temperature sensor for certain models and model years. This document details the terms of the warranty extension.
A201683 2043357_
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A151631 2045732_
THIS BULLETIN PROVIDES INFORMATION ON REMOVING A DAMAGED SCREEN FROM THE NON-RETURN VALVE.
AWA-16-08
This is a general communication notifying dealers that there is extended Warranty coverage available for the NVLD pressure switch for certain models and model years. This document details the terms of the warranty extension.
A911693 2028141_
THIS BULLETIN PROVIDES SOFTWARE UPDATE INFORMATION FOR THE MMMI 3G OR RMC FOR NAVIGATION DATA.
A921614 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A011691 20459981
This bulletin provides software update instructions to correct a EGR slow response in the engine control module.
A011691 2045998_
THIS BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO CORRECT A EGR SLOW RESPONSE IN THE ENGINE CONTROL MODULE.
A011689 2040962-
This bulletin provides information for a hardware and software update for TDI clean diesel vehicles with DTC P20E800.
A011688 2040403-
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored.
A871679 2041717-
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan.
A911689 2043595-
This technical bulletin provides software update information for incomplete text on the MMI screen.
A911690 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
Email - Audi TDI
This email gives an update on the consumer settlement program with regards to 2.0L and 3.0L TDI vehicles.
A011685 2041120-
This bulletin provides information regarding a software update for DTC P042000 and/or P043000.
A151630 2045732-
This bulletin provides information on removing a damaged screen from the non-return valve.
A441662 2010334-
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
A441663 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
Email - TDI Comp
This email gives an update on the current emissions issues with regards to 2.0L and 3.0L TDI vehicles.
A911685 2044670-
This technical service bulletin provides instructions for a software update to correct an issue with dropped calls in RMC MMI systems.
A921613 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A921612 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A001684 2037949-
This technical bulletin provides instructions for an an error message and updating with an SVM code.
A911682 2045580-
This bulletin provides information regarding a data connection message dur to the SIM card for T - Mobile subscribers.
A911681 2040406-
This bulletin contains instructions on how to fix when the GPS does not have the correct location or reception.
A46164920409645
THIS BULLETIN PROVIDES TESTING INSTRUCTIONS AND HOW TO PROPERLY FIX A BRAKE SQUEAK.
24CO
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. AS A RESULT, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY COME ON EVEN THOUGH THE CATALYTIC CONVERTERS ARE WORKING PROPERLY. IF THE MIL IS ON, A VEHICLE WILL NOT PASS AN EMISSIONS INSPECTION.
A37166820300075
THIS BULLETIN PROVIDE INSTRUCTIONS FOR WHEN THERE ARE HARSH GEAR SHIFTS BUT THERE IS NO FAULTS STORED AND YOU CAN DUPLICATE THE CONCERN.
A87167720447172
THIS BULLETIN PROVIDES INSTRUCTIONS ON CORRECTING A HIGH-PITCHED BUZZING NOISE IN THE CABIN WHEN THE FAN SPEED IS NO HIGHER THAN 2.
A17167720381198
THIS BULLETIN DETAILS INSTRUCTIONS ON HANDLING WHEN THE OIL MINIMUM MESSAGE APPEARS BUT THE OIL LEVEL IS ABOVE MINIMUM BUT NOT OVERFILLED.
A94168220175666
THE BULLETIN STATES A NORMAL FUNCTION OF THE HEADLIGHT SWITCH AND HOW TO FIX BUT NOT REPLACE. DEALER IS TO ADVISE CUSTOMER ON WHY THE HEADLIGHT SWITCH PRESSES IN.
EMAIL UPDATE
THIS EMAIL GIVES AN UPDATE ON THE CONSUMER SETTLEMENT PROGRAM WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A9416820313783
THIS BULLETIN LISTS INSTRUCTIONS FOR WHAT TO REPLACE WHEN A DIMMER CAP IS MISSING FROM THE HEADLIGHT SWITCH.
A91167120404066
THIS BULLETIN CONTAINS INSTRUCTIONS ON HOW TO FIX WHEN THE GPS DOES NOT HAVE THE CORRECT LOCATION OR RECEPTION.
A91166820446702
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR A SOFTWARE UPDATE TO CORRECT AN ISSUE WITH DROPPED CALLS IN RMC MMI SYSTEMS.
ATU 8/2016
RUNNING GEAR: AUDI MAGNETIC RIDE - KNOCKING NOISES FROM REAR SHOCKS ON S3 (8V) AND TTS (FV) BRAKE SYSTEM: BRAKING NOISES - BASIC PRINCIPALS FOR DIAGNOSIS AND REPAIR. RUNNING GEAR: MULTI-COLLISION BRAKE
A20167620437584
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A911667 2030465-
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A911667203046510
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A011673 2040403-
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
A01167320404033
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
A20167520437583
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A01166820404914
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INSTRUCTIONS TO RESOLVE A COOLANT WARNING AND STORED DTC.
A97165620424502
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR INSULATING THE BRACKET FOR THE STARTER MOTOR WIRING HARNESS WITH FABRIC TAPE TO REDUCE A NOISE.
A70165420447632
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR COVERING THE TRIM OF THE HEAD-UP DISPLAY TO REDUCE A RATTLING NOISE.
A46164520409644
THIS TECHNICAL SERVICE BULLETIN PREVIDES TROUBLESHOOTING FOR A SQUEAL NOISE FROM THE FRONT BRAKES.
A87167520447171
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR LESSENING A BUZZING SOUND FROM THE A/C SYSTEM ON CERTAIN SETTINGS.
A70165320447631
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR INSULATING THE TRIM PIECES OF THE HEAD-UP DISPLAY TO PREVENT A RATTLE SOUND.
A9116562040406-5
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
A91165620404065
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
2014
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2014 A6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2014 A6/S6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A40165520243184
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR CORRECTING A CLICKING SOUND FROM THE WHEEL BEARING(S).
A6/S6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
EMAIL TDI UPDATE
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A57162620220327
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INFORMATION FOR THE VEHICLE LOCKING SYSTEM.
A91165320446701
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR A SOFTWARE UPDATE TO CORRECT AN ISSUE WITH DROPPED CALLS IN RMC MMI SYSTEMS.
A91164720304658
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A91164820414303
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE REAR CAMERA WIRING HARNESS.
A91164920304659
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A201671 20437582
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE COOLANT THERMOSTAT WITH A NEW PART NUMBER TO RESOLVE A STORED DTC.
A101613 2044546-
THIS TECHNICAL SERVICE BULLETIN PROVIDES INFORMATION ABOUT LOCATING THE SOURCE OF AN OIL LEAK AND HOW TO PROCEED WITH A REPAIR.
A17167520381197
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A371664 20348634
THIS TECHNICAL SERVICE BULLETIN DESCRIBES HOW TO FLUSH ATF BEFORE REPLACING THE TCM TO RESOLVE AN ISSUE THAT CAUSES DTC P0706.
A20167020433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A2016720433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A24165420440032
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
A46163820409643
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO REPLACE BRAKE DISCS TO CORRECT A NOISE COMPLAINT.
EMAIL - TDI UPAT
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A96160720295633
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A01166220404032
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
A15162820399952
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO VERIFY A RATTLING NOISE HEARD AT COLD START AND TO REPLACE BOTH UPPER CHAIN TENSIONERS OF BANK 1 AND BANK 2 WITH AN OPTIMIZED PART.
A17167220381196
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A96160620295632
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A24165320440031
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
A57162520274063
THIS TECHNICAL SERVICE BULLETIN EXPLAINS THE DIFFERENCE BETWEEN KEYLESS GO AND AUDI ADVANCED KEY.
A91163920420133
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC.
A20166620437581
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
CUSTOMER LETTER
LETTERS TO CUSTOMERS EXPLAINING THAT THE REGISTRATION PERIOD FOR THE TDI GOODWILL PACKAGE FOR THE 3.0L TDI HAS BEEN EXTENDED.
EMAIL - TDI INFO
EMAIL TO DEALERS EXPLAINING THAT THE REGISTRATION PERIOD FOR THE TDI GOODWILL PACKAGE FOR THE 3.0L TDI HAS BEEN EXTENDED.
A20166420438921
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V6 ENGINES.
A011656 2040491-
The technical service bulletin is in regards to the MIL being on due to DTC P1B1C00 (coolant pump mechanical malfunction) being stored in the ECM. "Coolant System: Fault Turn Off Engine" and the Coolant symbol appear in the information panel. Condition can be caused by a defective thermostat or the diagnostic software is incorrectly displaying the warning.
A171670 2040644-
A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually occurs when the engine is warm. The MIL is sporadically on due to DTCs being stored in the ECM. A leak in the crankcase breather module can cause this condition.
A481669 2034351-
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly. The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead.
A481668 2043629-
Steering angle sensor cannot be programmed. The steering angle sensors cannot be calibrated and the steering end stops cannot be adapted on a vehicle with dynamic steering.
A171669 2040644-
A metallic whistling or grinding sound is heard from the engine compartment when th evehicle is at idle speed. The sound usually occurs when the engine is warm. The MIL is sporadically on due to DTCs being stored in the ECM. A leak in the crankcase breather module can cause this condition.
A171668 2038119-
The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level. There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A911632 2043595-
The customer complains that the display on the MMI screen is incomplete and text is missing. Additionally, the cluster DIS text may be using an incorrect menu language. The RMC manin unit is designed to support French, Spanish, and English languages. The control unit software has an issue that can cause th esystem language to default to German. The conditions occurs because German is not contained in the software.
A191667 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
Dealer Letter -
Effective immediately, the codes for the STP4 (2.0L TDI) and STP5 (3.0L TDI) actions will show the campaign code 23Q4 (2.0L TDI) and 23R8 (3.0L TDI) only on the Inventory Vehicle Open Campaign/Action Report. Elsa and ServiceNet will continue to display them as STP4 (2.0L TDI) and STP5 (3.0L TDI).
A661546 2030471-
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped.
A461630 2042646-
Customer may complain about brake squeak or squeal with light moderate pedal pressure. The noise is created by the brake pad material. A new brake pad (part number 4G0698151K) with improved compound has been developed. The supplier cannot currently produce this part in high volume due to factory capacity, which is causing a delay in part availability. It is possible that installing the original brake pad (part number 4G0698151D) will reduce the noise, but doing so is not always effective.
A961604 2042811-
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting. The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. The Audi connect Gen1 system includes all vehicles that utilize a removable plastic SIM card. The Audi connect Gen2 system includes all vehicles that utilize an embedded SIM card. The root cause of all complaints cannot be attributed to the vehicle hardware because of the backend server configurations that need to be correct in order for Audi connect to work. For most sporadic complaints, the issue typically resides with the MBB backend server or with the source data provider (Google, INRIX, etc.), and not with the vehicle. In rare cases, the mobile network operator (AT&T, T-Mobile) can be the cause of the complaint. For most static complaints, the issue can be attributed to the user account subscription or possibly the vehicle hardware.
A191666 2043142-
The MIL is sporadically on. One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
A421630 2029953-
Cracking or clicking noises are heard from the rear of the vehicle in the C pillar area when it is driven over bumps or rough roads. The noise comes from the upper shock absorber mounting. Optimized damper mounting gradually introduced in production.
A201659 2041594-
MIL on; (DTC P046100 - Fuel level sensor, circuit range/performance). MIL is on during normal driving conditions, city or highway at any speed.
Elsa Newsletter
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition.
A011652 2040491-
MIL on (DTC P1B1C); message in information panel: "Coolant System: Fault Turn Off Engine" The condition is caused either a defect with the thermostat (in model year 2012 and 2013 vehicles) or The diagnostic software is incorrectly displaying the warning. No technical issue exists. Solutions are an improved thermostat installed in production and the diagnostic software has been updated.
A191665 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A011649 2041120-
The MIL is on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. New ECM software implemented to correct the condition.
A401549 2018194-
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A911529 2013422-
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A001578 2021205-
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement.
A171568 2028440-
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A201559 2011703-
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.
155820415945
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201558 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-56 dated November 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A911526 2042097-
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.
A401548 2042603-
When the vehicle is driven between 35 mph and 75 mph, a noise can be heard in the front of the vehicle. The customer may say that the noise is coming from the steering column area, and may describe the sound as buzzing, humming, whistling, whining, grinding, howling, and/or droning. The best way to understand the complaint is to discuss it with the customer. Faulty wheel bearing(s) may cause the noise.
A901560 2042644-
In vehicles with PR code 9Q7, display content is sporadically not shown in the driver information system and text is superimposed on the information line of the on-board computer. Incorrect software in the instrument cluster.
A571517 2035173-
Supersedes Technical Service Bulletin Group 57 number 13-98 dated December 9, 2013. Customer may report that the automatic door lock function cannot be deactivated. The ?Lock when driving? (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door.
A461526 2042646-
Customer may complain about brake squeak or squeal with light moderate pedal pressure. The noise is created by the brake pad material. A new brake pad (part number 4G0698151K) with improved compound has been developed. The supplier cannot currently produce this part in high volume due to factory capacity, which is causing a delay in part availability. It is possible that installing the original brake pad (part number 4G0698151D) will reduce the noise, but doing so is not always effective.
A241551 2038212-
Supersedes Technical Service Bulletin Group 24 number 14-50 dated August 28, 2014. The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
155620415944
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201556 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-55 dated November 6, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
2613202026757 2
An AdBlue message may appear in the instrument cluster either because there is a fault in the
Campaign Circula
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged. Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve.
A911524 2026611-
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The
A971552 2042450-
A rattling noise is heard from the right dash panel area when the car is driven with light acceleration (between 15 mph and 25 mph). The bracket for the starter motor wiring harness has a locating tab that can vibrate.
A911528 2042013-
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. The following message appears in the MMI: ?This service is currently unavailable. Please try again later.? The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Additionally, if the vehicle is a model year 2016 A6, A7, or TT, the customer may not be able to see speed and flow traffic information in the navigation map screen, and may consistently see that no traffic reports are available. For these vehicles, traffic is provided by INRIX online.
Dealer Letter-Da
This document contain information on the upcoming emissions service action 17F9 in regards to the crankcase pressure regulating valve.
155520415943
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201555 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-50 dated October 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
A701550 2029280-
Supersedes Technical Service Bulletin Group 70 number 15-45 dated April 15, 2015. The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. Because there is no attachment to the trim carrier in the speaker cut-out, this area is the likely source of the vibration.
A201554 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A201552 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A511510 2009967-
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing.
A461525 2022584-
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.
A201550 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-47 dated August 5, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A911522 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-10 dated August 25, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
A201548 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-46 dated May 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911519 2041430-
Supersedes Technical Service Bulletin Group 91 number 15-04 dated July 22, 2015. The customer complains that the rearview camera image is not displayed on the MMI display. DTC 02203 (audio/video input 1) is logged in the rearview camera system control module. An issue with the wiring harness may cause the condition.
A461524 2040964-
Supersedes Technical Service Bulletin Group 46 number 15-14 dated June 29, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure.
A461523 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. New brake pads and/or discs have not been properly imbedded after installation. Aftermarket pads or discs are installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time. Discs are grooved. There is chemical contamination on the braking surface of the brake disc due to wheel or tire cleaner being sprayed directly onto the brake disc. There are ?pad marks? on the brake disc as a result of brake pad material transferring to the discs. Pad marks can occur when a vehicle has been parked for long periods of time in a wet or snowy environment.
A901557 2042121-
The head-up display will not power on or does not work. After the next bus silence (for example, waiting five minutes after the driver side door is locked), the head-up display works correctly. There is a software deviation that affects software versions 0304 (on A6 and A7 vehicles) and 0021 (on A8 vehicles).
A011545 2042071-
Engine warning lamp is illuminated. EPC lamp is illuminated. The engine runs irregularly. DTCs related to the cylinder on demand (COD) function are stored in the engine control module, J623 (address word 01). See the Service section of this bulletin for a complete list. A delay during the actuation of the COD adjusting mechanism is possible during the switch between 8 and 4 cylinder mode.
A441557 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A511509 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing.
Scheduled Maint
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Thereafter, all remaining scheduled services are due every 10,000 miles or 1 year after previous service, whichever occurs first.
A911516 2038927-
Supersedes Technical Service Bulletin Group 91 number 14-70 dated November 6, 2014. The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. DTCS for the affected camera may also be logged. Incorrect component.
A911517 2042013-
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern.
A011544 2041944-
The MIL is on and/or glow plug light on. DTCs are stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Cars exhibiting the issue outlined in this TSB will also show a pattern in the DTC expanded ambient conditions under the P200200 fault code. Soot mass measured value above 40 g. Soot mass calculated value approximately 30 g. Kilometers since last regeneration value are above 500,000 m. The current ECM software does not accurately detect a momentary rise in DPF backpressure, resulting in a soot overload fault.
A871570 2041717-
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception.
A961501 2019260-
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
Email Mandatory
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
A171565 2038129-
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A191562 2025303-
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A011542 2041787-
DTCs are stored in the ECM. There may be soot buildup on the moveable elements of the pressure sensing glow plug (PSG).
A9615002027416-6
Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
A911512 2036575-
Supersedes Technical Service Bulletin Group 91 number 15-80 dated March 20, 2015. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user?s myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations, accessing weather or other online information, or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. 2016 A6 and A7 vehicles have a known software issue that requires the myAudi PIN to be entered with each ignition cycle. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. Thi
A911510 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-90 dated June 5, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up). No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
A871567 2041717-
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
A571513 2027406-
Supersedes Technical Service Bulletin Group 57 number 11-54 dated August 18, 2011. Audi advanced key (keyless entry) is inoperative on all doors, but the engine can be started with the keyless starting system (keyless go). The keyless starting system (keyless go) is a standard feature; Audi advanced key is an optional feature. All vehicles have an engine start-stop button (-E408-) and touch sensor surface on the outer door handles, but this does not mean that the optional Audi advanced key function is installed.
A571512 2028207-
Supersedes Technical Service Bulletin Group 57 number 12-62 dated January 9, 2012. The trunk cannot be unlocked with the button on the remote, with the button in the driver?s door panel, or with the handle on the lid of the trunk. Vehicles have a ?VALET? button in the glove box that activates the valet parking feature, which prevents unauthorized access to the trunk. When the valet parking feature is activated, the trunk can only be opened mechanically with the key.
2041594/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201547 2041594-
The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A011538 2041566-
DTC P103200 (NOx sensor signal too high) is stored in the engine control module (ECM). Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts.
A211522 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-21 dated November 26, 2014. The MIL is on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall off due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039584/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A9415712039584-2
Supersedes Technical Service Bulletin Group 94 number 15-59 dated January 29, 2015. A bulb failure warning for one or several taillight functions appears in the instrument cluster, but the taillights are operating normally. The warning only occurs at very low outside temperatures. DTC entries are logged in the comfort system central control module. The transistor in the taillight is a component of the bulb failure monitor. The transistor is out of tolerance, which causes the bulb failure monitor to not see enough current consumption when outside temperatures are very low. This causes a false lamp failure warning.
A481566 2034351-
Supersedes Technical Service Bulletin Group 48 number 15-65 dated March 23, 2015. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A0115362041120-2
Supersedes Technical Service Bulletin Group 01 number 15-26 dated June 30, 2015. The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). The diagnostic limitations were too narrow.
A0115322040962-2
Supersedes Technical Service Bulletin Group 01 number 15-25 dated June 19, 2015. The MIL is on. DTC P20E800 (Reductant pressure too low) is stored in the engine control module. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Hardware and software update is needed.
A1915612025303-5
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A0115292041097-1
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
A301519 2019850-
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
SB-01-15-29
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
A011526 2041120-
The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow.
A011528 2040508-
Supersedes Technical Service Bulletin Group 01 number 15-21 dated April 29, 2015. The MIL is on. DTC P046100 (Fuel level sensor circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). DTC P046100 can be caused by miscalculations within the ECM software.
A461514 2040964-
Customer may complain about brake squeak or squeal with light to moderate pedal pressure.
A911598 2018187-
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A871564 2010146-
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
A011525 2040962-
The MIL is on. DTC P20E800 is stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Software update is needed.
A911594 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
A911595 2040926-
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
A971550 2034863-
Supersedes Technical Service Bulletin Group 37 number 13-18 dated October 16, 2013. Customer may report that the gearbox warning message is on. DTC P0706 (driving mode sensor, implausible signal) is stored in the transmission control module (TCM), J217 (address 02). There is a reaction between the TCM and the automatic transmission fluid (ATF) in vehicles within a specific VIN range.
Executive Servic
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
A011524 2040491-
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
A901555 2030193-
Supersedes Technical Service Bulletin Group 90 number 12-31 dated July 16, 2012. Customer states all or part of the picture generated from the top view camera system has an unnatural hue. To achieve a natural-looking top view camera image, the camera system constantly adjusts the displayed colors based on environmental conditions. In certain lighting conditions, the system responds to vibrant nearby colors (from the vehicle or other objects) by automatically adding a complementary color to rebalance toward white, which can lead to color deviations. For example, a red object can cause the system to add a green hue. The strength of the added color depends on the brightness of the object and the ambient light.
A911590 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-87 dated May 18, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). Q7 and Q3 vehicles are not affected by this condition. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A171563 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A971548 2013504-
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
A551537 2031273-
Supersedes Technical Service Bulletin Group 55 number 14-34 dated March 21, 2014. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative. This feature is installed on the A6/A7 from CW 22/2013 production and the A8 from CW 45/2011 production with Audi advanced key (PR No. 4I3).
A911588 2026390-
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
A871563 2010146-
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911587 2040406-
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle's actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. No DTCs related to the GPS antenna or MMI system are present. If the sky view is blocked because the vehicle is in a parking structure, below ground, or next to large buildings, it is normal for the GPS location or vehicle direction indicated on the MMI navigation map to not match the vehicle's actual location or direction of travel. The blocked sky view prevents the vehicle from receiving satellites, and the system may be temporarily lost until four satellites can be received. This is a normal condition, and is not related to the condition described above. Replacing the MMI main unit will not change this behavior. A potential failure in the internal hardware of the MMI main unit can cause the GPS signal to be blocked, even if good reception is available. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A201546 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-45 dated May 6, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911583 2030465-
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814. This bulletin only applies to vehicles with MMI3G+ Navigation (PR Number "7T6") and to vehicles with MMI3G+ Navigation, but without Audi Connect (PR Number "7T6" with additional PR code of "PND"). Continual improvements to MMI software provides solutions to issues experienced in the field.
A421523 2029953-
Supersedes Technical Service Bulletin Group 42 number 13-19 dated September 24, 2013. Cracking or clicking noises are heard from the rear of the vehicle in the C pillar area when it is driven over bumps or rough roads. The noise comes from the upper shock absorber mounting.
A201545 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-43 dated December 19, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A921510 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
A011521 2040508-
The MIL is on. DTC P046100 is stored in the ECM. DTC P046100 can be caused by miscalculations within the ECM software.
A391515 2028902-
Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
A911582 2029903-
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
A941565 2012749-
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
A941566 2017566-
Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision.
A001575 2035505-
Supersedes Technical Service Bulletin Group 00 number 13-54 dated October 10, 2013. Audi of America (in conjunction with AUDI AG) is conducting a pilot program in the USA with a limited number of specially-built vehicles. These vehicles have a persistent internet connection and are designed to be accessed and started without the need for a traditional remote key. Instead, these vehicles use NFC (Near-field connectivity), or an iPhone with the Audi on Demand app, utilizing Bluetooth connectivity. The customer must leave the NFC card with the vehicle in order for the vehicle to be accessed and started.
A011519 2040403-
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective.
A701545 2029280-
Supersedes Technical Service Bulletin Group 70 number 14-37 dated April 24, 2014. The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. Because there is no attachment to the trim carrier in the speaker cut-out, this area is the likely source of the vibration.
A191558 2036852-
Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
A661549 2030471-
Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
A481565 2034351-
Supersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A911579 2038824-
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A911580 2036575-
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
A101511 2018288-
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A191557 2040043-
Customer states that engine overheats. No MIL. No related DTCs are stored. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the overheat condition for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above. No changes to production have been made, as no issue has been identified.
A171558 2038119-
Supersedes Technical Service Bulletin Group 17 number 14-52 dated September 2, 2014. The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A911578 2011500-
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A011514 2014753-
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A011513 2030580-
Supersedes Technical Service Bulletin Group 01 number 15-08 dated February 17, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs P15700 and/or P170100 may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
A171557 2010043-
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A941564 2017806-
Supersedes Technical Service Bulletin Group 94 number 15-60 dated February 12, 2015. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A151526 2039995-
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner.
A461505 2038056-
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit.
A011508 2030580-
Supersedes Technical Service Bulletin Group 01 number 15-06 dated January 16, 2015. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTC P157000 and/or DTC P170100 present in the ECM and the transmission control module, respectively.
A011507 2028344-
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
A941560 2017806-
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A461502 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A371555 2039650-
There is an oil leak from underneath the vehicle. The leak may appear to be from the transmission oil pan gasket. Although the leak may appear to be from the transmission oil pan gasket, there are multiple possible sources for the leak. The leak must be diagnosed to determine the actual location before any repairs are attempted.
A941559 2039584-
A bulb failure warning for one or several taillight functions appears in the instrument cluster, but the taillights are operating normally. The warning only occurs at very low outside temperatures. DTC entries are logged in the comfort system central control module. The transistor in the taillight is a component of the bulb failure monitor. The transistor is out of tolerance, which causes the bulb failure monitor to not see enough current consumption when outside temperatures are very low. This causes a false lamp failure warning.
A461500 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time
A901552 2039429-
The vehicle horn sounds abnormal or is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Contact the Audi Technical Assistance Center (TAC) before replacing any parts. No changes to production have been made, as no issue has been identified.
A011505 2036169-
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. This issue is related to the diesel fuel and not a technical problem with the vehicle.
A011506 2030580-
The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
A461599 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
Edition117
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
20 14 43 2035073
EVAP System Leak Detected NVLD very small leak
20144320350737
System Leak Detected.
2035073/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201443 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911472 2024323-
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
01140420353684
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011404 2035368-
Supersedes Technical Service Bulletin Group 01 number 14-84 dated July 28, 2014. MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
Edition116
Vehicle diagnostics
00147020392061
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
2038689/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4214222038689
Rattle noise from rear suspension
42142220386891
Rattle noise from rear suspension
A001470 2039206-
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
A421422 2038689-
Clunking or rattling noises are heard from rear suspension area when vehicle is driven over bumps. These noises can be caused by an improperly seated rear bump stop (which occurs when the rear bump stop was not fully inserted into the rear shock absorber mounting during PDI).
37J1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37J1UPDATE
TCM Update
Update Bulletin
On Audi A6 and A7 vehicle with 8 speed automatic transmissions manufactured within a specific period, problem which affects the shifting comfort may occur in isolated cases. This Update is in effect until removed. Procedure is valid only for vehicles that show the 37J1 code in the Elsa Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.
441456202256311
Steering wheel shimmy, vibration, and/or oscillation
A441456 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
A901451 2021151-
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
Update37J1
Update the TCM software to the latest level with SVM
Accessories Oper
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin.
2039187/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4614982039187/1
AUDI: A6, A7, A8 2014-2015 ELECTRONIC WARNING PARKING BRAKE WARNING LIGHT ON INSTRUMENT CLUSTER, WHICH IS CAUSED BY THE PARKING BRAKE CONTROL MODULE. *LJ
46149820391871
Electronic parking brake warning light on
A461498 2039187-
The electromechanical parking brake warning is illuminated in the instrument cluster. DTCs are stored in the electromechanical parking brake control module. These DTCs are often sporadic and the complaint cannot be reproduced in the workshop. The condition is caused by an issue with the electromechanical parking brake control module, J540.
Edition114
Wastegate linkage dissconnected
142120390062
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211421 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-20 dated November 17, 2014. MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
145320390181
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A191453 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
142020390061
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211420 2039006-
MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
Edition112
Technical bulletins and updates
A171453 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
2038927/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911470 2038927-
The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. DTCs for the affected camera may also be logged. Incorrect component.
2038904/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A681415 2038904-
The 12V outlet compartment in the rear center console is disengaged, causing the compartment to come out or to not close into the console. The compartment was bumped or kicked while open, causing it to disengage.
A911469 2038824-
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
Edition110
Technical bulletins and updates
00135720356692
When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
A571404 2027368-
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
2029136/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A871459 2029136-
Supersedes Technical Service Bulletin Group 87 number 14-52 dated July 14, 2014. The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Perform a test drive with the customer both before and after this repair to ensure a thorough understanding of the customer's concern. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08).
ATE1421
This communication provides important information on how to obtain and install the latest software for the John Bean VAG1943B, VAS6331, VAS6421 alignment tools.
44145520103346
Tightening wheel bolts
48146320282204
Steering wheel leather damage, all vehicles
A481463 2028220-
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
EDITION 108
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition108
Audi Elsa Newsletter
A871458 2035582-
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
A911466 2020399-
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
A911467 2021037-
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
149820381661
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
87D9UPDATEa
AC Pressure/Temperature Sensor
87D9a
AC Pressure/Temperature Sensor (NVLW)
A011498 2038166-
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
87D9
AC Pressure/Temperature Sensor
A441455 2010334-
Supersedes Technical Service Bulletin Group 44 number 13-46 dated December 9, 2013. Wheel bolt requires torque adjustment.
144120350736
The NVLD pressure switch may erroneously detect a very small leak.
A201441 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-34 dated June 26, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A371449 2037127-
Supersedes Technical Service Bulletin Group 37 number 14-24 dated May 1, 2014. A jerky accelerator response is felt when the vehicle is pulled away from a stop in reverse. Incorrect calibration of clutch program.
144020338362
Beginning with MY2009, the filler necks of various TDI clean diesel vehicles were equipped with a misfueling guard (Figure 1). The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. The misfueling guard is designed to remain in a locked position when a nozzle with a diameter typically suited for non-diesel fuels (approximately 13/16?, or 20.6mm) is inserted, to prevent further insertion of the nozzle into the filler neck. A nozzle with a larger diameter typically suited for diesel fuel (approximately 15/16?, or 23.8mm) will unlock the misfueling guard when inserted, allowing the nozzle to be further inserted into the filler neck.
2033836/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201440 2033836-
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Customer may also state that the flap is stuck in a locked position and it cannot be moved with fingers.
Edition106
Audi Elsa Newsletter
37 14 48 2030007
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.
37144820300075
Customer may report harsh shift concerns; no faults are stored and concern is reproducible
A371448 2030007-
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.
A911463 2028190-
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
Edition105
Audi Elsa Newsletter
2038098/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941452 2038098-
Supersedes Technical Service Bulletin Group 94 number 14-48 dated August 11, 2014. Center brake light warning is displayed in the instrument cluster. DTCs are stored. The center brake light is operational during visual inspection.
A641436 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Edition104
Audi Elsa Newsletter
143820381132
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
1494203058010
The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
2030580/10
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2038113/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011494 2030580-
Supersedes Technical Service Bulletin Group 01 number 14-77 dated May 21, 2014. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
A201438 2038113-
Supersedes Technical Service Bulletin Group 20 number 14-36 dated August 14, 2014. MIL on.DTC P310B is stored in the engine control module, J623 (address word 01), with symptom code 6183.
EDITION 103
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A921409 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
149120288422
Customer vehicle is fitted with unauthorized ECM tuning.
A011491 2028842-
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.
2035919/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911458 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-53 dated July 24, 2014. MMI 3G+ GPS location is inaccurate (MY13, MY14, & MY15).
145220381192
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A171452 2038119-
Supersedes Technical Service Bulletin Group 17 number 14-51 dated August 18, 2014. The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
Edition101
Audi Elsa Newsletter
24 14 50 2038212
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
A241450 2038212-
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
441454203027510
Repair Authorization
145120381191
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
2038119/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
145020381291
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
143620381131
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038113/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-20-14-36
AUDI: DIAGNOSTIC TROUBLE CODE (DTC) P310-B00, LOW FUEL PRESSURE REGULATION OUTSIDE OF SPECIFICATION, SPORADIC/PASSIVE. SYMPTOM 6183. MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2014 A4, A5, A5 CABRIOLET, A6, A7, A8, Q5. *PE
44145320302759
Repair Authorization
2038056/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2038058/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2038098/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46149420380561
Brake pad wear warning - pads not at minimum
TSB-94-14-49
AUDI: SOME VEHICLES ARE EXPERIENCING XENON HIGH BEAM FAILURE ON ONE SIDE, ALL LEDS FAILURE IN HEADLIGHT OR LED LOW BEAM ON ONE SIDE, RANGE CONTROL OF CORNERING LIGHT AND/OR HEADLIGHT FAILS. MODEL 2011-2015 A6. *PE
TSB-94-14-52
AUDI: SOME VEHICLES MAY EXPERIENCE A DISPLAY WARNING FOR CENTER BRAKE LIGHT, IN THE INSTRUMENT CLUSTER. MODEL 2014-2015 A6, A3 SEDAN. *PE
44145220302758
Repair Authorization.
A001467 2002047-
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC).
00146620379491
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
2024683/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A001466 2037949-
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
14-84
AUDI: REVISED WARRANTY ON TDI CLEAN DIESEL. *LJ
148420353683
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2036761/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011484 2035368-
Supersedes Technical Service Bulletin Group 01 number 14-81 dated June 24, 2014. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM). Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
A011485 2036761-
Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective.
Edition96
Technical bulletins and updates
Edition96-1
i-wire new wiring diagram application
2035919/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96148520274165
Sunglass holder will not close
A911453 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-41 dated April 30, 2014. MMI 3G+ GPS location is inaccurate (MY14 & MY13).
A961485 2027416-
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
2037756/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A461491 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A911452 2037756-
The customer complains about GPS navigation issues that may be antenna-related. No DTC entry is logged. This bulletin should be performed before any other bulletins that cover specific customer complaints. If the GPS antenna cable became partially connected during assembly or during a repair, it may still function. But, the partially-connected cable can cause an intermittent issue that does not cause a DTC to be logged.
A571402 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
2033355/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2037761/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46148820377611
Engine cannot be switched off if ABS warning on
A461488 2037761-
Customer may report that the engine cannot be switched off with warnings on in the instrument cluster (e.g., ABS/ESP).
A911451 2033355-
Supersedes Technical Service Bulletin Group 91 number 13-78 dated March 15, 2013. Adaptive Cruise Control (ACC) does not work. The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC C110BF0 (Adaptive cruise control sensor restricted view) is logged in the distance regulation control module, J428 (address word 13).
001465201173210
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
2037770/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 14 22 2037770
Software improvement with more robust onboard diagnostics. If ECM software is current or newer than below, this bulletin cannot be applied. Follow GFF instructions.
A001465 2011732-
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
A261422 2037770-
The MIL is on. DTC P20FE00 (Reductant Metering Unit Performance) is stored in the engine control module (ECM). The ECM software version is older than the specified software for this bulletin. If ECM software is current or newer than below, this bulletin cannot be applied. Follow GFF instructions. Software improvement with more robust onboard diagnostics.
2029136/6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2037213/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46148620225845
Brake pulsation diagnostic guidelines
A461486 2022584-
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
A871451 2037213-
Supersedes Technical Service Bulletin Group 87 number 14-50 dated May 14, 2014. The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.
A871452 2029136-
Supersedes Technical Service Bulletin Group 87 number 14-48 dated March 10, 2014. The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.
Edition94
Pending service solutions and bulletins
A911450 2018187-
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
AUD4927ENG
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
AWA1405
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
Edition93
Technical bulletins and updates
4014402023187
Squeaking noises when steering or maneuvering
40144020231874
Squeaking noises when steering or maneuvering
4014412018194
Shock absorber leaks: assessment aid
40144120181946
Shock absorber leaks: assessment aid
A401440 2023187-
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A401441 2018194-
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
Edition92
Idenifying and mixing factory fill engine coolants
143420350735
The NVLD pressure switch may erroneously detect a very small leak.
A201434 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
148120353682
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011481 2035368-
Supersedes Technical Service Bulletin Group 01 number 13-32 dated September 26, 2013. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01).Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
A191450 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
Edition89
ElsaPro Software update and technical bulletins
SM532014
Module
Service
Audi Tire Chain Information by Vehicle -- MY 2014
Service Informat
Audi Tire Chain Information by Vehicle -- MY 2014
2014 Audi Tire C
This document contians the Audi tire chain information for all MY 2014 vehicles.
2033379/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2034735/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 13 07 2033658
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A011479 2033379-
Supersedes Technical Service Bulletin Group 01 number 13-42 dated November 21, 2013. DTC P164D00 is stored in the engine control module. Red oil pressure warning light may be on. An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced.
A941442 2034735-
Supersedes Technical Service Bulletin Group 94 number 13-25 dated July 24, 2013. Customer complains about heavy condensation is present in the headlight, lower headlight lens cracking, and upper headlight housing cracking (at transition from lens to black surround). Workshop found no visible external force marks (from accident or debris impact) are present, one or both sides may be affected, and the vehicle is not equipped with halogen headlights. The production process causes stress on the headlights from the bumper, as well as torsional force from installation. The moisture is an optical condition that does not affect the function or performance of the headlights, and it will not lead to corrosion or damage of the internal headlight parts.
00146320335762
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
37 14 30 2003658
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37143020036586
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A001463 2033576-
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A371430 2003658-
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
EDITION 87
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
147720305809
The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition. Improved software for the comfort system central control module, J393 (address word 46) in production. Service software update will follow at a later date (to be determined).
2030580/9
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011477 2030580-
Supersedes Technical Service Bulletin Group 01 number 14-51 dated January 3, 2014. The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.
23M6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
23M6UPDATE
ECM Software Update (FED_EMS)
Update23M6
ECM Software Update
2037213/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
441450202256310
Steering wheel shimmy, vibration, and/or oscillation
A441450 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.
A871450 2037213-
The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Perform a test drive with the customer both before and after this repair to ensure a thorough understanding of the customer?s concern. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.
Update91i8
Google Maps Street View (NVLW))
A641433 2029714-
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required.
2037127/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 14 24 2037127
A jerky accelerator response is felt when the vehicle is pulled away from a stop in reverse. Incorrect calibration of clutch program. New software in the transmission control module (TCM), J217 (address word 02) addressed the condition.
371422202898511
Transmission warning message in cluster (P074100 stored in TCM)
37142420371271
Jerky accelerator response in reverse gear
A371422 2028985-
Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
A371424 2037127-
A jerky accelerator response is felt when the vehicle is pulled away from a stop in reverse. Incorrect calibration of clutch program.
A911441 2035919-
Supersedes Technical Service Bulletin Group 91 number 13-17 dated December 3, 2013. The vehicle is a model year 2013 vehicle and TSB 2036607: 91 MMI3G+ Navigation GPS Location is inaccurate, has been completed. The GPS location or vehicle direction indicated on the navigation map does not match the vehicle's actual location or direction of travel.
27 14 24 2025360
Low battery charge: Diagnosis tips and TAC instructions
A271424 2025360-
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.
Edition83
97 no start
2029280/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A701437 2029280-
Supersedes Technical Service Bulletin Group 70 number 14-36 dated March 31, 2014. The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse.
A911438 2033780-
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface.
44144920225639
Steering wheel shimmy, vibration, and/or oscillation
A441449 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
97144320367643
97 No start (DTC P068A00)
A971443 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition81
Elsa newsletter
A911436 2027903-
Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected.
A911437 2030947-
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
2026895/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition80
Elsa newsletter
144920284402
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
2036688/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46147820366881
Vehicle does not start, battery flat DTC stored (DTC U101100)
87D9UPDATE
AC Pressure/Temperature Sensor (NVLW)
A171449 2028440-
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A461478 2036688-
Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module. According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object.
Edition75
Technical bulletins and updates
Update87D9
AC Pressure/Temperature Sensor
920143
The Audi 2.0L Third Generation TDI Engine
144920368521
The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
97144220367642
97 No Styart (DTC P068A00)
A191449 2036852-
Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
A971442 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition79
Technical bulletins and updates
46147620341817
Brake noise analysis and handling
A461476 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-68 dated February 3, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
143220350734
The NVLD pressure switch may erroneously detect a very small leak.
2036132/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A901447 2036132-
Supersedes Technical Service Bulletin Group 90 number 14-45 dated January 14, 2014. Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control.
2031273/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201432 2035073-
upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A551434 2031273-
Supersedes Technical Service Bulletin Group 55 number 13-29 dated March 29, 2013. The movement-activated rear lid opening (also known as "Hands-free trunk release") is sporadically inoperative.
147520366682
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.
A011475 2036668-
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.
A911429 2026888-
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
A971441 2036764-
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition77
Technical bulletins and updates
147120367611
Updated oil pressure switch
97144120367641
97 No start (DTC P068A00)
A011471 2036761-
The MIL is on. DTC P164B(00) is stored in the ECM. The oil pressure switch is defective.
2029136/5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A871448 2029136-
Supersedes Technical Service Bulletin Group 87 number 13-40 dated February 11, 2013. The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Perform a test drive with the customer both before and after this repair to ensure a thorough understanding of the customer's concern. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.
01146920366681
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.
2036653/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011469 2036668-
The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.
A911428 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
A941433 2036653-
The rear taillight warning for the left or right taillight may display in instrument cluster upon vehicle start. The vehicle taillights are operating normally. DTCs are sporadically found in the comfort system central control module, J393 (address word 46). An intermittent taillight warning upon vehicle start may be possible in extremely cold weather, but rear light functionality is not lost. An ignition key cycle will reset the warning.
96148220363441
96 Alarm sounds when driver door is unlocked with mechanical key
A911427 2036575-
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered.
A961482 2036344-
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.
2036653
REAR TAILIGHT WARNING WILL APPEAR IN INSTRUMENT CLUSTER WHEN STARTING THE VEHICLE. 07/09/14*LJ
A871447 2010146-
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911426 2036576-
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
00145920297372
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
A001459 2029737-
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Edition73
Technical bulletins and updates
Edition72
Windows XP- End of Support (EOS) and new VAS diagnostic services
46146820341816
Brake noise analysis and handling
A461468 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-67 dated January 21, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. This TSB should not be used if another brake noise TSB is available for the vehicle. For additional helpful information, refer to the Audi Brake Systems brochure.
Edition71
Technical bulletins and updates
01146320336302
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
2033630/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011463 2033630-
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
TSB-01-14-63
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2008-2015 A3, A4, ALLROAD, TT, A5, A5 CABRIOLET, Q5, A6. *PE
A481457 2034351-
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
Edition70
Technical bulletins and updates
01146220361693
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011462 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
A911424 2020399-
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.
A941432 2017806-
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.
01145920361692
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44144720302757
Alignment - Repair Authorization
A011459 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
A441447 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. If the condition is due to outside influence (such as an accident), this TSB does not apply. In an effort to gain information on this condition, Audi of America is asking you to contact the Audi Technical Assistance Center (TAC) before you perform any repairs.
A461467 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-64 dated January 2, 2014. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
Edition69
Technical bulletins and updates
2036132/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A901445 2036132-
Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control.
2036191/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911423 2036191-
One of the TopView cameras will not calibrate. For issues with the Front TopView camera image being upside down after replacing J928, please reference TSB 2035912, 91 Front TopView camera cannot be calibrated; picture appears upside down. Improper setup of the calibration board and/or camera.
Edition68
Updates and suggestions
2035912/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24AD
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24ADUPDATEa
ECM Software Update (FED_EMS)
A911422 2035912-
Supersedes Technical Service Bulletin Group 91 number 13-16 dated November 27, 2013. After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed. The calibration cannot be completed. The coding of the camera control module is not completed correctly.
143120350733
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two components): part numbers 8K0906253 and 8K0906253B supersede to 8K0906253D. ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, which are integrated (one component): part numbers 8K0906253A and 8K0906253C supersede to 8K0906253E.
A201431 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A461466 2022584-
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
2036169/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011455 2036169-
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
A911419 2026895-
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
A461464 2034181-
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
2014 MY Schedule
Maintenance.
MY 2014 Audi Nor
Tire Pressure Table.
REV11142013
Tire Pressure Table.
Edition67
Audi Elsa Newsletter
PDI-2014 A6 TECH
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. This document is in Spanish.
PDI-2014 ALL MOD
This document contains the Audi vehicle condition checklist. This document is in Spanish.
Reference-Audi M
This document contains the Audi normal load condition tire pressure table. This document is in Spanish.
2035173/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44134620103345
Tightening wheel bolts
A441346 2010334-
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
A571398 2035173-
Supersedes Technical Service Bulletin Group 57 number 13-96 dated October 16, 2013. Customer may report that the automatic door lock function cannot be deactivated. The "Lock when driving" (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door.
TSB-44-13-46
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
A461363 2034181-
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
2035919/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911317 2035919-
GPS inaccuracies can be caused by several different factors. If it is unclear if this PSS applies, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket. Customer states the navigation system is not tracking the vehicle correctly. No DTCs related to the GPS antenna or MMI system are present. The issue occurs after the vehicle is parked overnight or for several hours in a parking garage or other similar enclosed space. A private home garage does not apply. The issue does not occur if the vehicle is parked overnight or for several hours in an open-sky environment. The condition continues for the duration of the drive. The issue only corrects itself with a 3-finger reset or during a vehicle sleep cycle. The vehicle is not a Q7 or A8. If the above conditions apply and the customer vehicle is a Q7 or A8, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket.
2035912/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9113162035912 1
The coding of the camera control module is not completed correctly.
A911316 2035912-
After the camera control module, J928, has been replaced, the front image is upside down and cannot be changed (Figure 1). The calibration cannot be completed. The coding of the camera control module is not completed correctly.
Audi Newsletter
Elso pro reminder.
Edition63
Audi Elsa Newsletter
4413442022563 8
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
44134420225638
Steering wheel shimmy, vibration and/or oscillation
A441344 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
2026757/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 13 20 2026757
An AdBlue message may appear in the instrument cluster either because there is a fault in the emission control system or because the system needs to be refilled. The AdBlue message displayed may vary depending on the model year of the vehicle.
A261320 2026757-
Supersedes Technical Service Bulletin Group 26 number 11-03 dated June 29, 2011. There is an AdBlue-related message displayed in the instrument cluster. MIL may or may not be illuminated.
A741315 2035757-
Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure.
132820350732
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel tank cools off. If the natural vacuum leak detection (NVLD) system cannot detect this natural vacuum during the system self-test, the DTC will be stored in the ECM.
2013282035073 2
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel ank cools off. If the natural vacuum leak detection (NVLD)
2035796/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
5813052035796 1
The seal is held onto the rear door by its own clamping force.
A201328 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-27 dated October 16, 2013. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
A581305 2035796-
The customer may report that the seal on the rear door is loose or deformed. The loose seal may cause noise when the vehicle is motion. The seal is held onto the rear door by its own clamping force. As passengers enter and exit the vehicle, the seal may become dislodged due to friction created when their clothing comes in contact with the seal.
Normal Load Cond
This document contains the Audi normal load condition tire pressure table.
TableA
Tabla de presión de los neumáticos de condición de carga normal para Audi modelo 2014
0013572035669 2
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7
A001357 2035669-
Supersedes Technical Service Bulletin Group 00 number 13-56 dated November 1, 2013. There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
AA001357-2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition61
Audi Elsa Newsletter
134720354632
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.
1713472035463 2
Electronic oil consumption measurement.
A171347 2035463-
Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
2014 Audi Techni
Audi Technician report.
9113142013790 8
The navigation DVD or other CD/DVD cannot be ejected.
A911314 2013790-
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
PDI-2014 A6-S6-A
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
PDIg
Informe del técnico de Audi
ReportS
Audi Technician Report
Tire pressure Ta
2014 Audi Normal Load Condition Tire Pressure Table.
0013562035669 1
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7
00135620356691
When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
A001356 2035669-
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
AA001356-1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
QRSB-2014 Audi A
This document contains the quick reference specification book.
A911311 2027718-
Supersedes Technical Service Bulletin Group 91 number 13-86 dated June 11, 2013. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.
A571397 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
Reference-2014 N
This document contains the Audi normal load condition tire pressure table.
Reference-Oil Ca
This document contains the Audi oil capacity chart.
Table
Audi Normal Load Condition Tire Pressure Table
134420354631
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan.
A171344 2035463-
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
A871346 2035582-
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Edition58
Audi Elsa Newsletter
PDIf
Lineamientos de entrega de Audi
132720350731
EVAP System Leak Detected NVLD (very small leak))
A201327 2035073-
MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
2035506/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
27 13 19 2029010
Low battery charge: excess current draw location
A271319 2029010-
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
A461359 2035506-
Customer or technician hears a thumping noise while braking. Customer or technician feels pulsations while braking. There is brake pad residue (also called ?pad marks?) on the brake discs. These conditions may be found at PDI, or after there are a few hundred miles on the odometer. These conditions may exist on the front and/or rear brakes.
27 13 18 2023282
Battery testing and charging - vehicles with BDM
A271318 2023282-
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
741312 2004327-4
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Chart
Audi Oil Capacity Chart
GuidelinesO
Audi delivery guidelines
PDI - 2014 A6-S6
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
PDI - 2014 All M
This document contains the Audi vehicle condition report checklist.
ReportC
Technician report
ReportF
Vehicle detail report
ReportG
Vehicle condition report
A511307 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing.
48K8UPDATE
Power Steering Control Unit Software (NVLW)
A441342 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
A571394 2035367-
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
A721309 2035357-
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
2029953/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4213192029953
Cracking noises from rear of vehicle
42131920299533
Cracking noises from rear of vehicle
A421319 2029953-
Supersedes Technical Service Bulletin Group 42 number 12-15 dated October 12, 2012. Cracking or clicking noises are heard from the rear of the vehicle in the C pillar area when it is driven over bumps or rough roads. The noise comes from the upper shock absorber mounting.
A901341 2010353-
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
A911308 2028190-
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.
Edition53
Audi Elsa Newsletter
A481354 2028220-
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
01132820332243
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.
2033224/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011328 2033224-
Supersedes Technical Service Bulletin Group 01 number 13-10 dated June 24, 2013. If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair. This also applies to any messages related to AdBlue shown in the DIS. These procedures are mandatory until further notice. Routine maintenance, PDI, and repair of other systems do not require prior authorization or a TAC ticket. Any repairs related to the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue or emissions) systems, or transmission completed without Repair Authorization via a Technical Assistance Center (TAC) contact will not be reimbursed. In an effort to gain information on the systems listed above, we are asking that you contact TAC before replacing any parts. This will assist us in diagnosing any potential issues.
A911304 2013422-
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
2034842/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911303 2034842-
Supersedes Technical Service Bulletin Group 91 number 13-94 dated July 24, 2013. The driver?s voice sounds muffled or background noise sounds very loud to other caller during Bluetooth calls. Voice recognition commands are not recognized or voice recognition accuracy is poor. The location of the microphones within the roof module make them susceptible to interference by the vehicle air vents and climate control settings. When the center air vents are pointed upward, they can cause a ?swirling? effect that affects the audio quality of Bluetooth® and voice recognition. This is particularly evident on hot days when the A/C system is set to ?auto?.
A101310 2018288-
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
44134020277795
Steering rack control unit cannot be coded
A441340 2027779-
Supersedes Technical Service Bulletin Group 48 number 12-33 dated October 22, 2012. After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual. All new replacement power steering control units (J500) must be coded and parameterized using online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then the SVM code is required to code and parameterize the new replacement control unit. The SVM code can be found in Parts Bulletin 9-97, which is available online through ETKA.
Audi
Quick reference specification book.
QRSB AUDI A6 S6
Quick reference specification book.
Quick Reference
Audi Quick Reference Specification Guide.
ReferenceB
Quick Reference Specification Book
A911302 2018187-
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A961373 2034322-
Supersedes Technical Service Bulletin Group 97 number 13-36 dated July 10, 2013. The vehicle alarm activates for no reason and it cannot be turned off. The alarm horn does not work. DTC/fault symptom combinations are found in the comfort system control module. The DTC can be static or sporadic. The wiring harness insulation for the alarm horn can be damaged during the vehicle production assembly. Because the cable is routed through the plenum chamber, water can enter into the cable via the damaged insulation. The water causes the alarm to activate for no reason or it causes the alarm horn to not work.
TSB-48-K-8
AUDI: UPDATED INFORMATION ON POWER STEERING CONTROL UNIT SOFTWARE, IN SOME VEHICLES, WITH ELECTROMECHANICAL POWER STEERING, HAVING SLIGHT IRREGULARITIES, MANUFACTURED A SPECIFIC PERIOD, MAINLY OCCURS WHEN TEMPERATURE IS AT FREEZING POINT. MODEL 2012-2014 A4, A5, Q5, A6, A7. *PE
A461356 2034181-
Supersedes Technical Service Bulletin Group 46 number 13-53 dated August 7, 2013. Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A641329 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Dealer Letter-Up
This communication is to inform you of a revision to Update 24Z6. The revision is in regards to the manifold actuator.
A851319 2035000-
Various "whistling" noises are heard from the blower motor when it is running, particularly when it is running at lower fan speeds. The noises may be intermittent, and may depend on the outside temperature, the position of the flaps, etc. The noises are subtle, and they may not be heard if the audio system is on or if the vehicle is moving. The noises may be caused by a section of the noise insulation on the heating and air conditioning unit.
A511306 2009967-
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing.
2013_06_ATU Audi
This document contains information on the Audi side assist update.
A481347 2034351-
Supersedes Technical Service Bulletin Group 48 number 13-45 dated July 10, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A571392 2022032-
Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).
Fluid Capacity C
This document contains the fluid capacity chart.
A911396 2026390-
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.
Edition46
Audi Elsa Newsletter
2034735/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941325 2034735-
Heavy condensation present in the headlight. Lower headlight lens cracking. Upper headlight housing cracking (at transition from lens to black surround). No visible external force marks (from accident or flying debris) are present. One or both sides may be affected. The vehicle is not equipped with halogen headlights. The production process causes stress on the headlights from the bumper, as well as torsion force from installation. The moisture is an optical condition that does not affect the function or performance of the headlights and it will not lead to corrosion or damage of the internal headlight parts.
TSB-94-13-25
AUDI: DURING PRODUCTION PROCESS, VEHICLES EXPERIENCE STRESS ON HEADLIGHTS, FROM BUMPER AND TORSION FORCE, FROM INSTALLATION CAUSING CRACKS TO APPEAR IN HEADLIGHTS, HAVING HEAVY CONDENSATION AND ALLOWING WATER TO ENTER. MODEL 2012-2014 A6. *PE
Edition45
Audi Elsa Newsletter
37 13 09 2028715
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
A371309 2028715-
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
TSB-37-13-09
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE
A911392 2030947-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.
2034516/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44133920302756
Alignment - Repair Authorization
A441339 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.
A961369 2034516-
Road lane markings are not detected or the Audi lane assist system is inoperative after the lane assist camera control module, J852, has been calibrated, the windshield has been replaced, or the air suspension level sensors have been adapted. A DTC for incorrect calibration may be stored in the camera control module (address word 85). The camera control module has not been properly calibrated; there is no technical problem.
A481345 2034351-
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A961367 2019260-
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
2033919/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011314 2033919-
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective.
A461347 2034387-
Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.
Edition43
Audi Elsa Newsletter
GuidelinesM
Audi delivery guidelines
PDI - 2014 A6 Ch
This document contains the Audi delivery guidelines checklist.
Edition42
Audi Elsa Newsletter
PDI - 2014 A6 S6
This document contains the Audi pre-delivery checklist.
2033802/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A961366 2033802-
Supersedes Technical Service Bulletin Group 96 number 13-57 dated May 2, 2013. Customer states the Homelink controls are pressed into the interior light assembly. Clips holding the Homelink buttons in place are too weak.
AWA-13-05
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
01131020332242
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.
2033224/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011310 2033224-
Supersedes Technical Service Bulletin Group 01 number 13-75 dated March 13, 2013. If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair. This also applies to any messages related to AdBlue shown in the DIS. These procedures are mandatory until further notice. Routine maintenance, PDI, and repair of other systems do not require prior authorization or a TAC ticket. Any repairs related to the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue or emissions) systems, or transmission completed without Repair Authorization via a Technical Assistance Center (TAC) contact will not be reimbursed. In an effort to gain information on the systems listed above, we are asking that you contact TAC before replacing any parts. This will assist us in diagnosing any potential issues.
01130920147538
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more conditions.
A011309 2014753-
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A191341 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
96136920345161
Lane assist inoperative
AWC-13-08
Audi is committed to enhancing the Initial Quality Experience for our Customers within the first days of vehicle ownership. We want to resolve any knowledge or technical concerns a customer may have about a new vehicle, and build a strong, positive, enduring relationship between dealer and customer. To support this commitment to both our dealers and our customers, Audi is introducing the Audi Second Delivery Program for MY2013 and MY2014 vehicles. The Program is applicable to all new MY2013 and MY2014 vehicles and includes a one-time reimbursement per VIN of $75. The Second Delivery may be performed at the dealership or a location of the customer?s choosing.
A911386 2027718-
Supersedes Technical Service Bulletin Group 91 number 12-68 dated November 12, 2012. When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.
Edition39
Audi Elsa Newsletter
A661330 2030471-
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Edition38
Audi Elsa Newsletter
GuidelinesN
Audi delivery guidelines
37-13-07
AUDI: SOME VEHICLES MAY LACK POWER OR WILL NOT MOVE AFTER STOP DUE TO SIMULTANEOUSLY DEPRESSING THE BRAKE AND ACCELERATOR PEDALS. *JS
94-13-19
AUDI: THE VEHICLE LIGHTS MALFUNCTION MESSAGE MAY BE DISPLAYED ON THE DASHBOARD CLUSTER. THERE IS NO FAILURE. ALSO INCLUDED MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL S7 MY 2012-2014, MODEL RS7 MY 2014. *JS
Edition36
Elsaweb Newsletter
00134920335761
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
57-13-89
AUDI: SOME VEHICLES, IN COLD WEATHER, OCCASIONALLY, CANNOT BE UNLOCKED USING THE DOOR HANDLE TOUCH SENSOR. ALSO INCLDED ARE MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL RS5 CABRIOLET MY 2014, AND MODEL S5 CABRIOLET MY 2011-2014. *JS
A001349 2033576-
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
2033812/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2033802/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 14 22 2028985
The fault occurs with ATF temperature below 60° C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
01138620336301
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
A011386 2033630-
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
A001348 2002047-
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
2036852/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941312 2017566-
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.
133820129135
Engine oil service - filter cartridge replacement. When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.
A171338 2012913-
Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement.
A191335 2025303-
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A571386 2027368-
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
2033355/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911378 2033355-
Adaptive Cruise Control (ACC) does not work. The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC is logged in the distance regulation control module, J428 (address word 13).
IQS
Audi On Track ? IQS Newsletter
A571385 2017082-
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A571384 2024463-
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. High early warranty information related to inoperative remote keys necessitates this repair authorization. Through our combined efforts and cooperation, we will be able to raise the level of Audi quality and overall customer satisfaction.
4413362022563
Steering wheel shimmy, vibration and/or oscillation
44134220225637
Steering wheel shimmy, vibration and/or oscillation
A441336 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
A941306 2017806-
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.
SB-AOS-13-01
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A571382 2017082-
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A911374 2024323-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
44133520225635
Steering wheel shimmy, vibration and/or oscillation
PDIm
Informe del técnico de Audi
PDIn
Informe del técnico de Audi
1335201004313
Engine oils that meet Audi Oil Quality Standards.
MaintenanceB
2014 Scheduled Maintenance Intervals
A6-S6
Audi Delivery Guidelines.
A6-S6-A
Audi Delivery Guidelines.
Scheduled Mainte
This document contains the scheduled maintence intervals.
A901238 2032113-
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
24ADUPDATE
ECM Software Update (FED_EMS)
0012402031473
Car wash brush bristles trapped in headlight to fender seam
A001240 2031473-
Bristles from car wash are discovered between headlight and front fender. The vehicle design in the area around the headlights has a gap that, when the vehicle is washed in car washes having a particular bristle angle and type, can trap these bristles in this area, tear away from the mechanism and lodge in the gap between the headlight and fender.
SB-2031473/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0112562031368
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module:
A011256 2031368-
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.