TSB_2069078_4
Service Bulletin/Repair Instructions
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB_2069078_4
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2072304_4
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2079732_2
This bulletin provides information when there is a paint issue on alloy wheels.
TSB_2073282_1
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the dipped beam is switched on.
TSB_2070568_6
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2024323_13
This bulletin provides information when the parking assistance gives false warnings.
TSB_2024323_12
This bulletin provides information when the parking assistance gives false warnings.
TSB_2060750_5
This bulletin provides information regarding UV leak additive for finding oil leaks.
TSB_2074846_4
This bulletin provides information about vibrations and rotational steering vibrations.
TSB_2018187_18
This bulletin provides information when there are speaker rattles, vibrations, or audio interference.
TSB_2069904_2
This bulletin provides information for all models regarding brake sounds.
TSB_2069078_3
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2075120_2
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
TSB_2056386_11
This bulletin provides information about the steering wheel alignment.
TSB_2072304_3
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2074846_3
This TSB provides information regarding rotational and other steerihng wheel vibrations.
TSB_2079732_1
This bulletin provides information when tehre is a paint issue on alloy wheels.
TSB_2047812_8
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator decomissioned).
TSB_2073917_2
This bulletin provides information for when there is a fluid sample request from Product Support.
TSB_2071264_2
This bulleitn provides information whent here are complaints about route guidance with Navigation.
TSB_2041717_14
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of the concern.
TSB_2042920_3
This bulletin provides information when there is corrosion on the tailpipes.
TSB_2070568_5
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
AOS-25-47
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
TSB_2060750_4
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
TSB_2027368_7
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
TSB_2070568_4
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2042920_2
This bulletin provides information when there is corrosion on the exhaust tail pipes.
TSB_2056019_4
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
TSB_2077320_2
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2071893_2
This TSB provides damage assessment guidelines for textile seat covers.
TSB_2077320_1
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2075530_2
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
TSB_2041717_13
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the concern.
TSB_2071185_2
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
TSB-2076945_1
This bulletin provides information about leather care and seat repair.
A6625162049680_3
This TSB provides information when the exterior rubber trim is spotted.
A3725312074822_2
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
A8724952041717_12
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
A6624152046229_5
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
A2724842074729_2
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic mode.
A4424092056386_10
This bulletin provides information regarding wheel alignment.
A0124482014753_13
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
A9124872024323_11
This TSB Provides information when parking assistance provides false warnings.
A9124842018187_17
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
A0024992070568_3
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
A9624072056019_3
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
A5724652022032_11
This bulletin provides diagnostic information regarding the locking system.
SM 64-2024
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A1524532075530_1
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
CampTip_RNA_Audi
Vehicle Concerns Before Recall Repair Available
A2424632074810_2
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is working; mileage below 50 km/32 miles.
A8724892041717_11
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless of the concern.
A0024932002047_13
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical Assistnce Center (TAC).
A4424082074846_2
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
A4524492075120_1
This bulletin provides information regarding the general approach to brakes rubbing.
A4624592069078_2
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic brakes.
A9124432074929_1
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
A0024902074853_1
This bulletin provides service information ror when the fuel tank cannot be fully filled.
A3724222074826_1
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
A4424062074846_1
This bulletin provides information vibrations and rotational steering wheel vibrations.
A2424612074810_1
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not working; mileage below 50 km/32 miles.
A2724762074729_1
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
A3724212074822_1
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
A9124322018187_16
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
A8224002041717_10
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
A0024872002047_12
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center (TAC).
A9124252018187_15
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
A9424822074347_1
This bulletin provides informationw hen there are optical concerns with the tail lights.
A9124162018187_14
This bulletin provides information when there are speaker rattles, vibration or audio interference.
A5724432027368_5
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
A5724422025031_3
This bulletin provides information when the exterior trunk handle is inoperative.
A1124002073917_1
This bulletin provides information for when there is a fluid sample request from Product Support.
A0024852021205_8
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
A9024842032113_9
This bulletin provides general information regarding outside air temperature readings.
A5724342017082_1
This bulletin provides information when the remote control key is inoperative.
A9424722073282_1
This bulletin provides information on visual concerns with the headlight lens.
A9124632044694_3
This bulletin provides information pertaining to MMI Navigation database concerns.
A0023822047812_7
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via the Mirror Server.
A912306202432310
This bulletin provides information when the parking assistance provides false warnings.
A4523362072304_1
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
A9023562032113_8
This bulletin provides general information about the outside air temperature reading.
A0023812070568_2
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
A9423672071954_1
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
A7423262071893_1
This bulletin provides damage assessment guidelines for textile seat covers.
A0023762071721_1
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans (Ghost faults).
A0123812028842_4
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
A0023742052680_4
This bulletin provides information on the additional reporting requirements for safety related inquiries.
A9123262071264_1
This bulletin provides information for when the customer has concerns about the navigation route guidance.
A6423922020552_1
This bulletin provides information for when exterior glass cleaning is needed.
A8723452041717_9
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
A4823412028220_1
This bulletin provides information for instances where the steering wheel leather is damaged.
A102326201828810
This bulletin provides information on checking for debris when replacing an engine.
A9423652061922_3
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and taillights.
A0023702021205_7
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
A912394201818713
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference.
A9423632061922_2
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty submissions.
A4423992056386_9
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4423982056386_8
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4623432069904_1
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
A9023222032113_7
This information bulletin contains a background on the outside air temperature reading.
A192336202530314
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
A4023512023187_7
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and repair is not needed.
A9623822056019_2
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored.
A012341201475312
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
DC_Alternator_6
Support for Customers Affected by Alternator Back-order
A6623942049680_2
This bulletin provides instructions for when the exterior trim has spots.
DC_Alternator_4
Support for Customers Affected by Alternator Back-order
DC_Alternator_5
Support for Customers Affected by Alternator Back-order
DC_Alternator_3
Support for Customers Affected by Alternator Back-order
A9123592036576_7
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s).
A4623402069078_1
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
DC_Alternator_2
Support for Customers Affected by Alternator Back-order
DC_Alternator
Support for Customers Affected by Alternator Back-order
DC_RECALLS
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
A572200202203210
This technical service bulletin provides troubleshooting information for the vehicle locking system.
SM 74-2022
This special notice is to inform dealers to return the parts listed only order the successor parts going forward.
A462234203418122
This technical service bulletin provides troubleshooting for brake noise.
A4822342065978_2
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly.
A642285202055211
This bulletin provides instructions on how to properly clean exterior glass.
SM 48-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
SM 47-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4522262067132_1
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs.
A4622312051095_6
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A442292202256321
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A8722272041717_8
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A872225201014617
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation system.
A9022572032113_6
This is an informational bulletin containing information about the outside temperature reading.
A402237202431811
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
DC_20220329
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
A1722172060750_3
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A4622282051095_5
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A9122752024323_9
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A462226202258411
This informational bulletin provides diagnostic information for brake conditions.
A192228202530313
This bulletin contains instructions for identifying and mixing factory fill coolants.
A6922772025730_2
This bulletin provides direction in order to address a customer complaint that the front seat belt(s) retract slowly.
A192227202530312
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4021302023187_6
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or maneuvered.
A4021312024318_1
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A002155201173212
This bulletin contains general instructions for software updates.
A4421842065160_1
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
DC 20210928
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
A9121342018187_1
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A8721162041717_7
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A0121102028842_3
This informational bulletin gives instructions for identifying chip tuning.
A4821092028220_9
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty.
2010AUMAINT0721
DSG / S Tronic: Added "Change fluid: S4, S5 only"
A0021482021205_6
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
SM 44-2021
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A9121042024323_8
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
011399202773211
01 MIL on, no leak in EVAP system (DTC P045600 in ECM. Software update needed.
A0021442052680_3
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage).
A1021222018288_9
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
A9021032058077_5
This bulletin contains instructions for determining unexpected Audi presense interventions.
A6421802020552_1
This bulletin provides instructions on how to clean exterior glass.
A8721132010146_1
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
ELSAallignAudi
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
37 13 04 2028561
New software in the gear shift control module addressed the condition.
A9021002032113_5
This information bulletin contains a background on the outside air temperature reading.
A4021242016453_4
This bulletin contains instructions for determining if bushings need to be replaced.
A7021722038029_8
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A5721752022032_9
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A9121862062713_1
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
A9421362023322_3
This informational bulletin contains information on the different shading of LED headlights.
A4621252054385_2
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill).
A4621222051095_4
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462123202258410
This informational bulletin provides diagnostic information for brake conditions.
A9421332061922_1
This informational contains instruction on how to document optical concerns for warranty claims.
A1721122060750_2
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A9121642024323_7
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
SM C-2020
This special notice is to inform dealers to return the part numbers listed (State of California only).
A9120242026611_7
This bulletin contains a guide for troubleshooting HD radio issues.
A1720112060750_1
This bulletin contains instructions for using the UV additive to find engine oil leaks.
21AUTIRECHAINS
Added new graphic to reflect where to find MY 21 information
A9020652032113_4
This information bulletin contains a background on the outside air temperature reading.
Audi Part Labels
Recall Reminder Part Labels
A1720062028440_5
This informational bulletin explains when the range display is empty in the on-board computer.
A1920042025303_1
This bulletin contains instructions for identifying and mixing factory fill coolants.
A9020512058077_4
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A0020382039206_3
This informational bulletin contains instructions on how to use the QR code in a TSB.
A9120702044694_2
This technical service bulletin provides troubleshooting for issues with the navigation map database.
A4020052024318_9
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9120652036576_6
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
A6420742020552_9
This bulletin provides instructions on how to clean exterior glass.
A0020372059437_1
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing some issues.
A872005201014615
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
A9020442032113_3
This information bulletin contains a background on the outside air temperature reading.
A0020362002047_1
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
A012054201475311
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A012046201475310
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A912039201818711
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A4420732056386_3
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A9020372058077_3
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A9020362058077_2
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A9419182012749_1
Exterior lights, moisture accumulation 2013-2021 A3 Cabriolet, 2016-2018 Sportback, 2004-2005 A4 Cabriolet, 2004-2008 S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8
20AUTIRECHAINS
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
A4419712022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7
145320381292
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A7019682038029_7
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A4019972018194_9
This bulletin contains repair instructions for leaking shock absorbers.
A0019262052680_2
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage.
ATUBody2019
Body components - Examples of customer misuse
ATUChassis2019
Wheel change mode/jacking mode - Description and usage
A0019252011732_1
00 Software Version Management (SVM), operating instructions
A9119882024323_6
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A1719982028440_4
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
A9619432056019_1
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off. Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
AWC 19-05
This communication is issued to inform dealers of updated shipping regulations related to lithium ion batteries.
AWC 19-04
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8
A4819792028220_8
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe
A0019222047812_6
This informational bulletin contains instructions for setting up and using the SD Creator program. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A8719912041717_6
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A9019192032113_2
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe
A9119652050565_2
This bulletin contains general software update instructions for vehicles with PR Code 7UH. 2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster
A0019212052680_1
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe
A961934 20489272
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A441969 2022563
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A001915 2047812
This informational bulletin contains instructions for setting up and using the SD creator program.
Maintenance Sche
Spark Plugs ? replace at 35,000 miles or 3 years, whichever occurs first. Then, every 40,000 miles or 3 years, whichever occurs first: Added: TTS 2.0L TFSI
A701866 2038029_
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A961721 2048927-
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A911750 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
Maint Flip Chart
Revision to Tires-rotate: 5K only; added "(except R8)"
A911745 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
A911743 2042097-
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI navigation.
SM 52-2017
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation 14s.
A941791 2012749-
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
A911736 2024323-
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A401774 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A401770 2018194-
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
A401768 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
SM 44-2017 EN
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward.
A401766 2024318
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A441764 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A171782 2010043-
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil change.
A301722 2019850-
This technical service bulletin provides guidelines for diagnosing the clutch plate.
A011710 2035002-
This bulletin contains diagnosis and repair information for DTC P049100 and P049200.
A401761 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A571740 2047432-
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored.
Edition76
Technical bulletins and updates
ATE-17-05
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
A701756 2038029-
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A871679 2041717-
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan.
A441662 2010334-
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
A441663 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A001684 2037949-
This technical bulletin provides instructions for an an error message and updating with an SVM code.
SM 76-2016
THIS SPECIAL NOTICE IS TO INFORM DEALERS TO RETURN ALL 07P-121-115-C /07P-198-210 AND ONLY ORDER PART NUMBER07P-121-115-E / 07P-198-210-A GOING FORWARD.
A911667 2030465-
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A911667203046510
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A40165520243184
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR CORRECTING A CLICKING SOUND FROM THE WHEEL BEARING(S).
A91164720304658
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A91164920304659
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A96160720295633
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A01166420442301
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE TO CORRECT AN ISSUE THAT CAUSES A CATALYST SYSTEM-RELATED DTC.
A96160620295632
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A011655 2035002-
This technical service bulletin is about the MIL being on due to DTCs being stored in the ECM. The DTCs may appear during monitoring of the secondary air system during the engine cold starting phase. The secondary air pressure can be influenced by several factors; which may include a leak in the vacuum system.
A911631 2039476-
The customer complains that the Audi connect online service in their 2011-2013 A8, 2012-2013 Q7, or 2013 A4, A5, A5 cabriolet, or Q5 vehicle only reaches 2G service. The customer has received a letter from T-Mobile and/or Audi of America regarding the issue. The VIN on the letter matches the VIN on the vehicle that is being serviced. The vehicle can be within or outside of the New Vehicle Limited Warranty. A telephone module that supports 3G service on the 1900MHZ band was installed beginning with model year 2014 vehicles. No repairs are necessary for model year 2014 vehicles and later. Video shows the service procedure.
A401549 2018194-
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A911529 2013422-
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A001578 2021205-
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement.
A171568 2028440-
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A201559 2011703-
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.
A911526 2042097-
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.
A911524 2026611-
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The
A011547 2035002-
Supersedes Technical Service Bulletin Group 01 number 15-46 dated October 8, 2015. The Mil is on. DTCs are stored in the ECM. The DTCs may appear during monitoring of the secondary air system during the engine cold starting phase. With the electric solenoid valves controlled, a diagnosis cycle is performed and the secondary air pressure is measured for a specified value. The secondary air pressure can be influenced by several factors; which may include a leak in the vacuum system.
A461525 2022584-
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.
A911521 2039476-
Supersedes Technical Service Bulletin Group 91 number 15-06 dated July 28, 2015. The customer complains that the Audi connect online service in their 2011-2013 A8, 2012-2013 Q7, or 2013 A4, A5, A5 cabriolet, or Q5 vehicle only reaches 2G service. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and 2013 Q5 vehicles. For 2012-2013 A6 and A7 vehicles see TSB 2039515. This bulletin does not apply to model year 2014 and newer. Starting with model year 2014, the new telephone module was installed in production. The model year 2014 A8 is not included in this repair. Model year 2014 was the last year before the A8 product improvement and ElsaPro may classify these vehicles as model year 2013 because these vehicles are the same from a technical and design standpoint. But unlike the model year 2013 vehicles, the model year 14 vehicles already have the updated telephone module in the MMI. Recently, T-Mobile (the service provider for Audi connect) has repurposed some of the GSM spectrum (3G on 2100Mhz band) to maximize 4G LTE coverage in certain metropolitan areas. Devices that do not support 3G service on the 1900MHZ band (including MMI main units of the vehicles to which this bulletin applies) will only receive 2G service when the switch is completed. The change currently only affects the markets listed above, but will affect other markets in coming years. This bulletin will be updated to include these markets as changes occur.
A701548 2038029-
Supersedes Technical Service Bulletin Group 70 number 15-47 dated September 21, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A011546 2035002-
Supersedes Technical Service Bulletin Group 01 number 13-25 dated August 23, 2013. The MIL is on. DTCs are stored in the ECM. The DTCs may appear during monitoring of the secondary air system during the engine cold starting phase. With the electric solenoid valves controlled, a diagnosis cycle is performed and the secondary air pressure is measured for a specified value. The secondary air pressure can be influenced by several factors; which may include a leak in the vacuum system or a faulty exhaust catalyst.
A441557 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A701547 2038029-
Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A961501 2019260-
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
Email Mandatory
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
2017266/9
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A481567 2017266-
Supersedes Technical Service Bulletin Group 48 number 14-62 dated September 23, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.
A171565 2038129-
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A191562 2025303-
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A871569 2020124-
Supersedes Technical Service Bulletin Group 87 number 14-49 dated April 25, 2014. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
A871567 2041717-
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
A721515 2041579-
One side of the front center armrest will not lay flat or even with the other side. The pin from the locking pawl is out of place.
A911506 2039476-
The customer complains that the Audi connect online service in their 2011-2013 A8, 2012-2013 Q7, or 2013 A4, A5, A5 cabriolet, or Q5 vehicle only reaches 2G service when in metropolitan areas. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and 2013 Q5 vehicles. For 2012-2013 A6 and A7 vehicles see TSB 2039515. The model year 2014 A8 is not included in this repair. Model year 2014 was the last year before the A8 product improvement and ElsaPro may classify these vehicles as model year 2013 because these vehicles are the same from a technical and design standpoint. But unlike the model year 2013 vehicles, the model year 14 vehicles already have the updated telephone module in the MMI. Recently, T-Mobile (the service provider for Audi connect) has repurposed some of the GSM spectrum (3G on 2100Mhz band) to maximize 4G LTE coverage in certain metropolitan areas. Devices that do not support 3G service on the 1900MHZ band (including MMI main units of the vehicles to which this bulletin applies) will only receive 2G service when the switch is completed. The change currently only affects the markets listed above, but will affect other markets in coming years. This bulletin will be updated to include these markets as changes occur.
A0115312033806-7
Supersedes Technical Service Bulletin Group 80 number 14-07 dated August 11, 2014. The MIL is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults may be stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss as a result of coolant migration in the electrical harness, faults in 08-Heating and Air Conditioning Electronics that result from coolant migration in the electrical harness, or a faulty N82 control valve.
TSB-01-15-31
AUDI: SOME VEHICLES WILL EXPERIENCE WARNING COOLANT LEVEL IS ON, ELEVATION OF ENGINE TEMPERATURE, AN ACTIVE LIMP HOME MODE DUE TO PERFORMANCE OF CLIMATE SYSTEM HEATING IS INSUFFICIENT DUE LOSS OF COOLANT RESULTING IN COOLANT MIGRATION OF ELECTRICAL HARNESS AND AIR CONDITIONING ELECTRONICS. MODEL 2010-14 A6, 7, 8, 4, 5, A5 CABRIOLET, TT, Q5, 7. *PE
A1915612025303-5
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A301519 2019850-
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
SB-01-15-29
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
A911501 2039476-
Supersedes Technical Service Bulletin Group 91 number 15-86 dated May 15, 2015. The customer complains that the Audi connect Online service in their 2011-2013 A8, 2012-2013 Q7, or 2013 A4, A5, A5 cabriolet, or Q5 vehicle only reaches 2G service when in metropolitan areas. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and 2013 Q5 vehicles. For 2012-2013 A6 and A7 vehicles see TSB 2039515.
A911598 2018187-
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A871564 2010146-
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
A911594 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
A911595 2040926-
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
Executive Servic
This document contains a fluid capacity chart as well as a chart that contains the part and part numbers needed for service.
A171563 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A971548 2013504-
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
A941567 2027773-
Supersedes Technical Service Bulletin Group 94 number 12-96 dated November 1, 2012. Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. For vehicles with halogen daytime running lights, refer to TSB 2017488: 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.
A911588 2026390-
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
A871563 2010146-
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911582 2029903-
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
A941565 2012749-
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
Dealer Letter -
This document contains general information on the upcoming warranty extension on the high pressure fuel pump.
A911579 2038824-
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A911580 2036575-
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
A101511 2018288-
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A911578 2011500-
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A011514 2014753-
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A171557 2010043-
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A701544 2038029-
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A011507 2028344-
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
Edition117
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
A911472 2024323-
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
00147020392061
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
A001470 2039206-
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
441456202256311
Steering wheel shimmy, vibration, and/or oscillation
A441456 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
A901451 2021151-
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
Accessories Oper
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin.
145320390181
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A191453 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
Edition112
Technical bulletins and updates
A171453 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A911469 2038824-
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
Edition110
Technical bulletins and updates
44145520103346
Tightening wheel bolts
48146320282204
Steering wheel leather damage, all vehicles
A481463 2028220-
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
A871458 2035582-
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
2038727/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911466 2020399-
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
A911467 2021037-
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
A941456 2038727-
A headlight system warning may be illuminated in the instrument cluster. One or more LEDs in the low beam are inoperative on one side. Internal cooling fan is inoperative in one headlight. DRL inoperative on one side. LED turn signal inoperative in one headlight. Diagnosis of the concern indicates that the headlight is at fault. Connector in the headlight is not properly seated.
TSB-94-14-56
AUDI: INFORMATION REGARDING THE ILLUMINATION IN THE INSTRUMENT CLUSTER OF HEADLIGHT SYSTEM WARNING DUE TO INOPERATIVE INTERNAL COOLING FAN IN HEADLIGHT, ON ONE SIDE, DRL INOPERATIVE AND THE LOW BEAMS ON ONE SIDE IS INOPERATIVE. 2010-13 A8. *PE
A441455 2010334-
Supersedes Technical Service Bulletin Group 44 number 13-46 dated December 9, 2013. Wheel bolt requires torque adjustment.
144020338362
Beginning with MY2009, the filler necks of various TDI clean diesel vehicles were equipped with a misfueling guard (Figure 1). The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. The misfueling guard is designed to remain in a locked position when a nozzle with a diameter typically suited for non-diesel fuels (approximately 13/16?, or 20.6mm) is inserted, to prevent further insertion of the nozzle into the filler neck. A nozzle with a larger diameter typically suited for diesel fuel (approximately 15/16?, or 23.8mm) will unlock the misfueling guard when inserted, allowing the nozzle to be further inserted into the filler neck.
2033836/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201440 2033836-
Supersedes Technical Service Bulletin Group 20 number 13-26 dated May 15, 2013. Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Customer may also state that the flap is stuck in a locked position and it cannot be moved with fingers.
Edition106
Audi Elsa Newsletter
A911463 2028190-
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
37 14 46 2025535
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
37144620255354
Transmission faults stored (DTC P1703 or U1111)
A371446 2025535-
Supersedes Technical Service Bulletin Group 37 number 14-41 dated August 1, 2014. There is no customer complaint with this concern. Transmission faults stored (DTC P1703 or U1111).
48146220172668
Electric steering column adjustment is inoperative
A481462 2017266-
Supersedes Technical Service Bulletin Group 48 number 14-59 dated June 2, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition.
A641436 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
AL-20082011
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A WARRANTY EXTENSION HAS BEEN ISSUED FOR 10 YRS OR 120, 000 MILES, WHICHEVER OCCUR FIRST, ON EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS, UNDER SPECIFIC CONDITIONS. MODEL 2008-2011. *PE
AL-20092011
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER SPECIFIC CONDITIONS, THE EMISSIONS CONTROL SYSTEMS WARRANTY, FOR FUEL INJECTOR REPLACEMENT, HAS BEEN EXTENDED TO 10 YRS OR 120,000 MILES, WHICHEVER HAPPENS FIRST. MODEL 2009-2011. *PE
Edition104
Audi Elsa Newsletter
A921409 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
149120288422
Customer vehicle is fitted with unauthorized ECM tuning.
A011491 2028842-
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.
Edition102
Audi Elsa Newsletter
145020381291
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
37 14 41 2025535
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
37144120255353
Transmission faults stored (DTC P1703 or U1111)
A001467 2002047-
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC).
00146620379491
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
A001466 2037949-
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
Edition96
Technical bulletins and updates
Edition96-1
i-wire new wiring diagram application
001465201173210
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
A001465 2011732-
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
46148620225845
Brake pulsation diagnostic guidelines
A461486 2022584-
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
Edition94
Pending service solutions and bulletins
A911450 2018187-
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
AUD4927ENG
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
46148420311353
Yellow warning light for electric parking brake on, ACC inoperative once
A461484 2031135-
Supersedes Technical Service Bulletin Group 46 number 13-57 dated August 16, 2013. The yellow warning for electromechanical parking brake (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module.
4014402023187
Squeaking noises when steering or maneuvering
40144020231874
Squeaking noises when steering or maneuvering
4014412018194
Shock absorber leaks: assessment aid
40144120181946
Shock absorber leaks: assessment aid
A401440 2023187-
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A401441 2018194-
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
2036482/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911448 2036482-
The volume of the radio, navigation announcements, or output of the Bluetooth telephone system changes when the ignition is switched off, then switched back on, the volume is muted, then unmuted, and the MMI is switched off by a long press of the volume knob, then restarted without an ignition cycle. All vehicles with MMI 2G/3G/3G+/MIB Navigation are affected.
Edition92
Idenifying and mixing factory fill engine coolants
A191450 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
Edition90
Technical bulletins and updates
Edition89
ElsaPro Software update and technical bulletins
37 14 31 2013002
As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Automatic transmission fluid is leaking at the sump pan gasket.
37143120130025
ATF pan leaks
A371431 2013002-
Supersedes Technical Service Bulletin Group 37 number 11-19 dated January 31, 2011. Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak.
48145920172667
Electric steering column adjustment is inoperative
A481459 2017266-
Supersedes Technical Service Bulletin Group 48 number 13-51 dated August 30, 2013. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.
TSB-48-14-62
AUDI: ELECTRICALLY ADJUSTABLE STEERING COLUMN ADJUSTMENT FAILS TO ADJUST VERTICAL AND IS RESTRICTED AND UNDER TENSION DUE TO MODULE CROSS CARRIER AND UNFAVORABLE TOLERANCES TO STEERING COLUMN. MODEL 2003-2010 A8, 2005-2011 A6, 2007-2014 Q7. *PE
37 13 07 2033658
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
00146320335762
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
37 14 30 2003658
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37143020036586
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A001463 2033576-
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A371430 2003658-
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
Edition87
Technical bulletins and updates
EDITION 86
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition86
Technical bulletins and updates
37 14 26 2025535
If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
37142620255352
Transmission faults stored (DTC P1703 or U1111)
A371426 2025535-
Supersedes Technical Service Bulletin Group 37 number 11-20 dated May 13, 2011. There is no customer complaint with this concern. DTCs may be stored. If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
441450202256310
Steering wheel shimmy, vibration, and/or oscillation
A441450 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.
Update91i8
Google Maps Street View (NVLW))
2028561/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 14 25 2028561
New software in the gear shift control module addressed the condition. There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". This is a generic message in the instrument cluster that a transmission fault has occurred and Limp Home Mode might be activated if the malfunction continues.
37142520285617
Gearbox warning light on.
A371425 2028561-
Supersedes Technical Service Bulletin Group 37 number 13-06 dated May 13, 2013. There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". This is a generic message in the instrument cluster that a transmission fault has occurred and Limp Home Mode might be activated if the malfunction continues. DTCs are stored in the gear shift control module. New software in the gear shift control module addressed the condition.
27 14 24 2025360
Low battery charge: Diagnosis tips and TAC instructions
A271424 2025360-
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.
A871449 2020124-
Supersedes Technical Service Bulletin Group 87 number 13-44 dated August 26, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure.The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged.
2037052/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44144920225639
Steering wheel shimmy, vibration, and/or oscillation
A441449 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A851421 2037052-
There is no airflow from the outer vents. Noises may be heard from the side of the dash during operation. DTCs are stored in the air conditioning control module. The mechanical stop for vent linkage is broken, allowing for the linkage to extend past intended range of operation.
A911437 2030947-
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
A911435 2026895-
Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
Edition80
Elsa newsletter
144920284402
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
46147820366881
Vehicle does not start, battery flat DTC stored (DTC U101100)
A171449 2028440-
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A461478 2036688-
Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module. According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object.
Edition75
Technical bulletins and updates
Edition79
Technical bulletins and updates
A941435 2024877-
Supersedes Technical Service Bulletin Group 94 number 12-00 dated December 21, 2012. The warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 - 14 is stored in the headlamp range control module, J431 (address word 55). Both headlights function normally. The vehicle is equipped with adaptive (cornering) lighting. There is a software issue in the dynamic headlight range control module.
A911429 2026888-
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
Edition77
Technical bulletins and updates
A801406 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-05 dated September 11, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module (address word 02). Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A911428 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
Edition84
ElsaPro Tip: "notes"
A911427 2036575-
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered.
A871447 2010146-
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911426 2036576-
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
2035757/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A741417 2035757-
Supersedes Technical Service Bulletin Group 74 number 13-15 dated November 15, 2013. Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D).
00145920297372
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
A001459 2029737-
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
01146720284453
Optimized software in the engine control module.
2028445/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011467 2028445-
Supersedes Technical Service Bulletin Group 01 number 13-43 dated November 26, 2013. The MIL is on, often illuminating at temperatures below 0°C/32°F. DTC P010600 is store in the ECM. Optimized software in the engine control module.
Edition71
Technical bulletins and updates
01146220361693
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011462 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
01145920361692
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011459 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
Edition69
Technical bulletins and updates
A461466 2022584-
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
01145520361691
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011455 2036169-
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
A911419 2026895-
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
44134620103345
Tightening wheel bolts
A441346 2010334-
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
Edition65
Audi Elsa Newsletter
TSB-44-13-46
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
SB-48326
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. *PE
0113432028445 2
New software in engine control module addressed the condition.
01134320284452
Manifold Abs.Pressure or Bar.Pressure Range/Performance G71/-F96 - implausible signal)
2028445/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011343 2028445-
Supersedes Technical Service Bulletin Group 24 number 12-11 dated January 25, 2012. MIL on, often illuminating at temperatures below 0°C/32°F. DTC is store in the engine control module. Optimized software in the engine control module.
Audi Newsletter
Elso pro reminder.
Edition63
Audi Elsa Newsletter
4413442022563 8
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
44134420225638
Steering wheel shimmy, vibration and/or oscillation
A441344 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
2035757/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
7413152035757 1
Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without
A741315 2035757-
Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure.
2035755/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9113152035755 1
A loud noise is heard from the MMI screen while it is opening or closing.
A911315 2035755-
A loud noise is heard from the MMI screen while it is opening or closing. The MMI screen will not open or close at all. supplier error affecting certain MMI display mounts can cause the internal gear of the mount to get stuck after a few cycles. MMI display mounts produced between October 2012 and September 2013 with part number 4E0857273F are affected. This vehicle is out of production. This issue only affected spare parts.
9113142013790 8
The navigation DVD or other CD/DVD cannot be ejected.
A911314 2013790-
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
2034000/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137820340003
Lane Change Assistant sporadically inoperative
A961378 2034000-
Supersedes Technical Service Bulletin Group 96 number 13-74 dated September 11, 2013. Customer complains that Audi Lane Change Assistant deactivates or is sporadically inoperative. Message ?Side Assist Unavailable? is displayed in the Driver Information Display when the system deactivates. Workshop finds that Audi Lane Change Assistant can be activated without issue. DTCs are stored in the Lane Change Assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi Lane Change Assistant temporarily.
Reference-Oil Ca
This document contains the Audi oil capacity chart.
A871346 2035582-
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Edition58
Audi Elsa Newsletter
27 13 19 2029010
Low battery charge: excess current draw location
A271319 2029010-
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
741312 2004327-4
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Chart
Audi Oil Capacity Chart
A441342 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
A571394 2035367-
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
4013342018194
Shock absorber leaks: assessment aid
40133420181945
Shock absorber leaks: assessment aid
4013352023187
Squeaking noises when steering or maneuvering
40133520231873
Squeaking noises when steering or maneuvering
A401334 2018194-
Supersedes Technical Service Bulletin Group 40 number 10-04 dated April 1, 2010. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber. As a result of a leak because the shock absorber is damaged. As a result of residue from when the shock was filled during production, or of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A401335 2023187-
Supersedes Technical Service Bulletin Group 40 number 12-23 dated May 14, 2012. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A901341 2010353-
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
43132320187659
Self-leveling compressor inoperative
A431323 2018765-
Supersedes Technical Service Bulletin Group 43 number 13-14 dated April 11, 2013. The self-leveling system can no longer be adjusted with the MMI. The compressor for the self-leveling system continues to run after the engine has been switched off and the vehicle has been locked. DTCs may be stored in the level control system module. Because of poor performance or failure of the air suspension compressor, the vehicle ride height cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected.
Edition53
Audi Elsa Newsletter
A481354 2028220-
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
A801305 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A911304 2013422-
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A101310 2018288-
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A481351 2017266-
Supersedes Technical Service Bulletin Group 48 number 10-09 dated August 13, 2010. Electric steering column adjustment is restricted or does not work at all. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. The seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, so the electric steering column adjustment fails.
A911302 2018187-
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A481349 2015819-
Supersedes Technical Service Bulletin Group 48 number 13-43 dated April 19, 2013. The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.
A871344 2020124-
Supersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
A481348 2021191-
Supersedes Technical Service Bulletin Group 48 number 13-46 dated July 22, 2013. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.
A641329 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
A011321 2027732-
Supersedes Technical Service Bulletin Group 01 number 13-99 dated May 17, 2013. MIL on. DTC P045600 (very small EVAP leak) stored in engine control module (ECM), J623 (address word 01). No leaks found in the EVAP system. Software update needed.
A801304 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-03 dated May 13, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A461353 2034181-
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
2013_06_ATU Audi
This document contains information on the Audi side assist update.
Edition46
Audi Elsa Newsletter
A481346 2021191-
Supersedes Technical Service Bulletin Group 40 number 09-06 dated August 3, 2009. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.
Edition45
Audi Elsa Newsletter
37 13 09 2028715
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
37130920287152
Rough gear changes both when accelerating and slowing down
A371309 2028715-
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
TSB-37-13-09
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE
A911392 2030947-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.
A871343 2020124-
Supersedes Technical Service Bulletin Group 87 number 13-42 dated June 11, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
A961367 2019260-
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
A461347 2034387-
Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.
Edition42
Audi Elsa Newsletter
01130920147538
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more conditions.
A011309 2014753-
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A191341 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A871342 2020124-
Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.
SM562013
Seat Belt
37-13-07
AUDI: SOME VEHICLES MAY LACK POWER OR WILL NOT MOVE AFTER STOP DUE TO SIMULTANEOUSLY DEPRESSING THE BRAKE AND ACCELERATOR PEDALS. *JS
Edition37
Elsaweb Newsletter
2027732/11
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011399 2027732-
Supersedes Technical Service Bulletin Group 01 number 13-85 dated April 11, 2013. MIL on. DTC P045600 (very small EVAP leak) stored in engine control module (ECM), J623 (address word 01). No leaks found in the EVAP system. Software update needed.
00134920335761
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
A001349 2033576-
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
2028561/6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 13 06 2028561
Gearbox warning light on.
37-13-06
AUDI: GEARBOX LIGHT ILLUMINATED. A TRANSMISSION MALFUNCTION MAY OCCUR. THE VEHICLE MIGHT ACTIVATE LIMP HOME MODE. *JS
Edition35
Elsaweb Newsletter
2033666/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4313172033666
Vehicle lowers itself, air suspension warning light on, level sensor error (PR-2MB or 1BK)
43131720336661
Vehicle lowers itself, air suspension warning light on, level sensor error (PR-2MB or 1BK)
ATE-13-11
Audi of America is pleased to inform you of the release and automatic delivery of two new Required Special Tools used on Audi vehicles. Starting May 20, 2013, every Audi dealer will be shipped one AT-351 Special Tool Package, Freight F.O.B. Snap-On OEM and invoiced directly by the Audi Special Tools Program (Snap-On Business Solutions - SBS).
2028561/5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A371304 2028561-
Supersedes Technical Service Bulletin Group 37 number 13-82 dated January 23, 2013. There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". DTCs are stored in the gear shift control module, J587 (address word 81). New software in the gear shift control module addressed the condition.
A481343 2015819-
Supersedes Technical Service Bulletin Group 48 number 11-15 dated January 10, 2011. The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.
2027732/10
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4313142018765
Self-leveling compressor inoperative
A011385 2027732-
Supersedes Technical Service Bulletin Group 01 number 13-84 dated April 3, 2013. MIL on. DTC P0456 (very small EVAP leak) stored in engine control module (ECM), J623 (01). No leaks found in the EVAP system.
A431314 2018765-
Supersedes Technical Service Bulletin Group 43 number 12-11 dated October 29, 2012. The self-leveling system can no longer be adjusted with the MMI. The compressor for the self-leveling system continues to run after the engine has been switched off and the vehicle has been locked. DTCs may be stored in the level control system module, J197 (address word 34). Because of poor performance or failure of the air suspension compressor, the vehicle ride height cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected.
461335201713011
Brakes squeel
A461335 2017130-
Supersedes Technical Service Bulletin Group 46 number 11-16 dated December 9, 2011. Customer complains of brake squeal.
A001348 2002047-
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
A191335 2025303-
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A571385 2017082-
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
ATE-13-05
VWGoA is pleased to inform you of the release and automatic delivery of new Required Special Tools used on Audi vehicles. Starting March 25, 2013, every Audi dealer will be shipped one AT-348 Special Tool Package, Freight F.O.B. Snap-On OEM and invoiced directly by the Audi Special Tools Program (Snap-On Business Solutions - SBS).
4413362022563
Steering wheel shimmy, vibration and/or oscillation
44134220225637
Steering wheel shimmy, vibration and/or oscillation
A441336 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
A571382 2017082-
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A911374 2024323-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
2028561/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 13 82 2028561
New software in the Selector Lever Control Module (J587) addressed the condition. The gear lever display flashes. The message "gearbox problem, journey can be continued with restrictions" is shown.
37138220285614
Gearbox warning light on - Faults P0605 and/or P17EC stored in Selector lever module 81
44133520225635
Steering wheel shimmy, vibration and/or oscillation
1335201004313
Engine oils that meet Audi Oil Quality Standards.
A941200 2024877-
Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update.
A901238 2032113-
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
2020124/8
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A871237 2020124-
Supersedes Technical Service Bulletin Group 87 number 12-32 dated September 5, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C Pressure/Temperature Sensor G395 leaks refrigerant. This causes Sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the J519 Central Electrics Control unit to Sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of Vehicle Electrical System Control Module J519. Vehicle Electrical System Control Module J519 transfers the information provided by the sensor via the comfort data bus to Climate Control Module J255.
4012272024318
Clicking noise from wheel bearing
40122720243183
Clicking noise from wheel bearing
A401227 2024318-
Supersedes Technical Service Bulletin Group 40 number 12-26 dated September 26, 2012. Clicking or clacking noise when maneuvering or parking. Normal driving dynamics may cause microscopic movements between the wheel bearing and wheel bearing housing.
4312112018765
Self-leveling compressor inoperative
A431211 2018765-
Supersedes Technical Service Bulletin Group 43 number 12-08 dated February 2, 2012. The self-leveling system cannot be adjusted any more with the MMI. The compressor for the self-leveling system continues to run after switching off the engine and locking the vehicle. DTCs may be stored. Because of poor performance or failure of the compressor for air suspension, the vehicle position cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected.
TSB-43-12-11
AUDI: THE CONTROL MODULE, AS A SAFEGUARD, WILL LOWER VEHICLE TO LOWEST POSITION AND ILLUMINATE WARNING LIGHT DUE TO FAILURE OF COMPRESSOR, FOR AIR SUSPENSION OR POOR PERFORMANCE, VEHICLE NOT ABLE TO BE ADJUSTED. MODELS 2004-2008 A6 (C6), 2013 A6 (C7); 2004-2013 A8 (D3-D4); 2013 A7 (C7); 2007-2011 Q7. *PE
A941292 2012749-
Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.
2712152031145
Excessive Voltage DTCs present in multiple control units
SB-7-101512
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2712142031145
Excessive Voltage DTCs present in multiple control units
A171232 2018550-
Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil.
3712692031140
Warning message in cluster, no driving mode can be selected - Faults P09140, U040400, U010300 stored in TCM
A371269 2031140-
The gearbox warning light comes on. No driving modes can be selected. The driving mode is not shown on the gear lever. Entries are logged in the memory under diagnosis address 02 (gearbox control unit). New software in the Selector Lever Control Module (J587) addressed the condition.
SB-2031140/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
3712682028561
Gearboxwarning light on - Faults P0605 and/or P17EC stored in Selector lever module 81
A371268 2028561-
Supersedes Technical Service Bulletin Group 37 number 12 ? 52 dated May 31, 2012. There is no customer complaint about the gearbox. The gear lever display flashes. The message "gearbox problem, journey can be continued with restrictions" is shown. The entry P0605 or P17EC is logged under the diagnosis address 81- Selector lever. New software in the Selector Lever Control Module (J587) addressed the condition.
SB-2028561/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911263 2021151-
Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle.
A911262 2024323-
Supersedes Technical Service Bulletin Group 91 number 10 - 60 dated September 28, 2010. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
3012152030732
Red warning light for brake fluid on with no brake performance concerns -
4012262024318
Clicking noise from wheel bearing
SB-2030846/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-94-12-83
AUDI: THE INSTRUMENT CLUSTER DISPLAYS WARNING FOR HEADLIGHT DYNAMIC RANGE CONTROL MODULE. *PE
TSB-94-12-82
AUDI: INSTRUMENT CLUSTER ILLUMINATES SHOWING HEADLIGHT DYNAMIC RANGE CONTROL, WHICH MAY HAVE FAULTY CONTROL UNIT. MODELS A8, A6 AND AUDI Q7 (2008-13). *PE
TSB-91-12-42
AUDI: BACK UP CAMERA IMAGE IS INCORRECT OR OFF, TOO BRIGHT, TOO DARK, FUZZY, DISTORTED OR OPAQUE. MODELS AUDI Q5, Q7, A4, A5, A5 CABRIOLET (2009-14), A5, S5 (2008-14), A8 (2010-14) AND A6 (2011-14). *PE
TSB-96-12-34
AUDI: WHEN SELECTING REVERSE GEAR, THE PICTURE OF REARVIEW CAMERA FAILS TO APPEAR, SPORADICALLY. CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE
TSB-94-12-76
AUDI: DISPLAYED IN THE INSTRUMENT CLUSTER IS THE WARNING FOR THE DYNAMIC HEADLIGHT RANGE CONTROL. *PE
TSB-24-12-11
AUDI: WHEN TEMPERATURE IS BELOW 0%/C/32%F, THE MIL LIGHT FOR ENGINE, COMES ON. TO ADDRESS CONDITION, THERE IS A NEW SOFTWARE FOR ENGINE CONTROL MODEL (ECM). *PE
TSB-30-11-10
AUDI: CERTAIN MODEL YEAR VEHICLES MAY EXPERIENCE A CONDITION WITH THE CLUTCH MALFUNCTIONING, BURNT SMELL OR NOT RETURNING TO ORIGINAL POSITION. *PE
TSB-94-11-56
AUDI: ON CERTAIN MODEL YEAR 2008 TO 2013 VEHICLES, DURING ADJUSTMENT OR REMOVAL, BRAKE LIGHT SENSORS BEING REPLACED ARE DAMAGED, PREVENTING PROPER ANALYSIS. *PE
SA-19H1-08
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM
SA-19H1-10
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM
SA-19H1-F1
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. UNDER CERTAIN CONDITIONS THE COOLANT PUMP MAY LEAK. *RM
SA-48326
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM
SA-US-06
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN. *RM
SA-19H1
AUDI SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. *KB
TSB-38-11-05
AUDI: TRANSMISSION PROBLEMS RESULTING IN A DELAYED ENGAGEMENT WHEN COLD OR NO DRIVE ON FIRST ENGAGEMENT. *RM
TSB-94-10-38
AUDI: DAYTIME RUNNING LIGHTS DO NOT WORK. DAYTIME RUNNING LIGHTS DO NOT WORK ON VEHICLES WITH XENON HEADLIGHTS. THE THUMB WHEEL OR OPTION FOR DAYTIME RUNNING LIGHTS IS TURNED OFF BY MISTAKE. *PE
TSB-01-10-13
AUDI: MIL ON; ROUGH IDLE; ONE OR MORE OF THE FOLLOWING DTCS ARE STORED-DTC P0300 (RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED); DTC P0301-0312 (CYL. 1 MISFIRE DETECTED-CYL.12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE
TSB-01-10-09
AUDI: MIL ON; ROUGH IDLE, ONE OR MORE OF THE FOLLOWING DTCS ARE STORED-DTC P0300 RANDOM/MULTIPLE CYLINER MISFIRE DETECTED; DTC P0301-0312 (CYL. 1 MISFIRE DETECTED-CYL. 12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE
TSB-00-10-02
AUDI: SOFTWARE VERSION MANAGEMENT (SVM) OPERATING INSTRUCTIONS. DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). TROUBLESHOOTING INFORMATION IS INCLUDED. *PE
TSB-24-09-28
AUDI: MIL ON AND ONE OR MORE OF THE FOLLOWING DTCS ARE STORED INTHE ECM DATA MEMORY-P310B (LOW PRESSURE FUEL SYSTEM REGULATION, FUEL PRESSURE OUTSIDE TOLERANCE); P129F OR P008B (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO HIGH); P129F OR P008A (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO LOW); P2540 (LOW PRESSURE FUEL SYSTEM, PRESSURE OUT OF RANGE; AND P0087 (RAIL FUEL PRESSURE SYSTEM, PRESSURE TOO LOW). *PE
TSB-43-09-10
AUDI: SELF LEVELING COMPRESSOR INOPERATIVE. SELF LEVELING SYSTEM CANNOT BE ADJUSTED ANY MORE WITH THE MMI; COMPRESSOR FOR SELF LEVELING SYSTEM CONTINUES TO RUN AFTER SWITCHING OFF THE ENGINE AND LOCKING THE VEHICLE. BECAUSE OF POOR PERFORMANCE OR FAILURE OF COMPRESSOR FOR AIR SUSPENSION, VEHICLE POSITION CANNOT BE ADJUSTED. *PE
TSB-01-09-06
AUDI: SOFTWARE VERSION MANAGEMENT (SVM), OPERATING INSTRUCTIONS. SVM IS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (RE-PROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN AUDI VEHICLES. THIS SYSTEM USES THE VAS 5051B OR VAS 5052 DIAGNOSTIC TOOLS TO SEND VEHICLE SPECIFIC DATA TO THE SVM DATABASE, TO DOWNLOAD INSTRUCTIONS FROM THE SVM DATABASE, AND TO FLASH CONTROL UNITS FOR IDENTIFIED SOFTWARE UPDATES. *PE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.