TSB_2074436_3
Service Bulletin/Repair Instructions
This bulletin provides information when the horn sound quality is poor.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB_2074436_3
This bulletin provides information when the horn sound quality is poor.
TSB_2069078_4
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2069904_3
This bulletin provides information for all models regarding brake sounds.
TSB_2072304_4
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_20741717_15
This bulletin provides information on the GFF test plan required for AC compressor replacements regardless of the concern.
TSB_2075120_3
This bulletin provides information about the general approach for brake vibration concerns.
TSB_2079732_2
This bulletin provides information when there is a paint issue on alloy wheels.
TSB_2082846_1
This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.
SM 01-2026
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
TSB_2073282_1
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the dipped beam is switched on.
TSB_2028902_5
This bulletin provides informaiton when the transmission warning message appears in the cluster; P074100 stored in the TCM.
TSB_2028985_13
This bulleitn procides informaiton when tehre is a transmission warning mssage in the instrument cluster; P074100 is stored in the TCM.
TSB_2059335_7
This bulletin provides information when there are noises from the area around the instrument cluster.
TSB_2074729_3
This bulletin provides informationwhen noises/vibration are detected from front of vehicle in dynamic mode.
TSB_2082047_1
This bulletin provides information when howling noises are heard from the rear of the vehicle at 34 mph; quattro with self-locking center differential.
TSB_2082323_1
This bulletin provides informaiton when the engine is not running smoothly, misfiring.
TSB_2052680_6
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
AOS-26-25
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.
TSB_2074808_4
The high-voltage batteries in electric vehicles are subject to various ageing effects which could lead to the energy content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years
TSB_2022032_12
This bulletin provides diagnostic information for the vehicle locking system.
TSB_2070568_6
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2081531_1
This Reporting obligation requests that technicians contact the Technical Assistance Center (TAC) when the diagnostic tester refers to this reportin gobligation or to TPI 2033392.
TSB_2023187_8
This bulletin provides informaiotn regarding squeaking noises when steering or maneuvering.
TSB_2081405_1
This bulletin provides informaiotn about various infortainment system complaints.
TSB_2024323_13
This bulletin provides information when the parking assistance gives false warnings.
DC_Audi_CF_ Airbag
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent warning regarding counterfeit replacement airbag inflators that are being installed in used vehicles.
TSB_2024323_12
This bulletin provides information when the parking assistance gives false warnings.
TSB_2021205_10
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2059335_6
This TSB provides information when there are noises from the area around the instrument cluster.
TSB_2052680_4
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
TSB_2080329_1
This bulletin provides informaiotn when there are noises from the headliner.
TSB_2080681_1
This bulletin provides information regarding contact checks for event memories, intermittent.
TSB_2060750_5
This bulletin provides information regarding UV leak additive for finding oil leaks.
TSB_2074846_4
This bulletin provides information about vibrations and rotational steering vibrations.
TSB_2056019_5
This bulletin provides information when the anti-theft alarm activates for no reason, or does not activate.
TSB_2061669_3
This bulletin provides service infrmation for workshop mode with Audi connect vehicles.
TSB_2021205_9
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2074808_3
This bulletin provides additoinal information to assist in determining the energy content of lithium-ion high-voltage batteries.
TSB_2018187_18
This bulletin provides information when there are speaker rattles, vibrations, or audio interference.
TSB_2080186_1
This bulletin provides information when the MIL is on, DTC P310B00 in ECM; Vapor pocket formation in fuel system.
TSB_2069904_2
This bulletin provides information for all models regarding brake sounds.
TSB_2069078_3
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2075120_2
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
TSB_2030471_8
This bulletin provides informaiton when the license plate mouting bracket threaded inserts are stripped.
TSB_2056386_11
This bulletin provides information about the steering wheel alignment.
TSB_2072304_3
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2074846_3
This TSB provides information regarding rotational and other steerihng wheel vibrations.
TSB_2079732_1
This bulletin provides information when tehre is a paint issue on alloy wheels.
TSB_2047812_8
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator decomissioned).
TSB_2073917_2
This bulletin provides information for when there is a fluid sample request from Product Support.
TSB_2071264_2
This bulleitn provides information whent here are complaints about route guidance with Navigation.
TSB_2041717_14
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of the concern.
TSB_2042920_3
This bulletin provides information when there is corrosion on the tailpipes.
TSB_2070568_5
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2074436_2
This bulletin provides information when the horn sound quality is poor.
AOS-25-47
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
TSB_2060750_4
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
TSB_2027368_7
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
TSB_2010353_6
This TSB provides informatin when the cigarette lighter element does not eject, or the cigarette lighter is inoperable.
TSB_2070568_4
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2042920_2
This bulletin provides information when there is corrosion on the exhaust tail pipes.
TSB_2056019_4
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
TSB_2077320_2
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2031473_6
This service information TSB describes a cosmetic issue after using a car wash.
TSB_2071893_2
This TSB provides damage assessment guidelines for textile seat covers.
Circular_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
Dealer_19N8_20250328
Removed expiration date, Updated part numbers in parts and claiming sections, General circular updates
TSB_2077320_1
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2075530_2
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
TSB_2041717_13
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the concern.
TSB_2071185_2
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
TSB-2076945_1
This bulletin provides information about leather care and seat repair.
A6625162049680_3
This TSB provides information when the exterior rubber trim is spotted.
A3725312074822_2
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
A8724952041717_12
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
A6624152046229_5
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
A2724842074729_2
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic mode.
A4424092056386_10
This bulletin provides information regarding wheel alignment.
A0124482014753_13
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
A9124872024323_11
This TSB Provides information when parking assistance provides false warnings.
A9124842018187_17
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
A0024992070568_3
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
A9324342074808_2
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A9624072056019_3
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
A5724652022032_11
This bulletin provides diagnostic information regarding the locking system.
A1524532075530_1
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
CampTip_RNA_Audi
Vehicle Concerns Before Recall Repair Available
A2424632074810_2
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is working; mileage below 50 km/32 miles.
A8724892041717_11
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless of the concern.
A0024932002047_13
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical Assistnce Center (TAC).
A4424082074846_2
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
A0024922031473_5
This bulletin provides informationw hen there are car was brush bristles trapped in the seam between the headlight and fender.
A4524462072304_2
This bulleitn provides information when there is an implausible signal in the ABS/ESC speed sensor.
A4524492075120_1
This bulletin provides information regarding the general approach to brakes rubbing.
A4624592069078_2
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic brakes.
A3924722059129_6
This bulletin provides information when there are noises and/or vibration in tight turns in vehicles with quattro drive.
A0124342074976_1
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in petrol.
A9124432074929_1
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
A9324042074808_1
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A0024902074853_1
This bulletin provides service information ror when the fuel tank cannot be fully filled.
A3724222074826_1
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
A4424062074846_1
This bulletin provides information vibrations and rotational steering wheel vibrations.
A2424612074810_1
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not working; mileage below 50 km/32 miles.
A2724762074729_1
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
A3724132074750_1
This bulletin provides information about replacing the clutch end cover.
A3724142074751_1
This bulletin provides information about replacing the clutch end cover.
A3724212074822_1
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
A9124322018187_16
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
A8224002041717_10
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
A0024872002047_12
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center (TAC).
A9124252018187_15
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
A9424822074347_1
This bulletin provides informationw hen there are optical concerns with the tail lights.
DC_Q5 Hybrid
This document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday, June 24.
A9124162018187_14
This bulletin provides information when there are speaker rattles, vibration or audio interference.
A5724432027368_5
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
A9424812073332_3
This bulletin provides information when there is noise while steering.
AWA 24-04
Diagnosed and confirmed malfunction of the vehicle’s AEB system that resulted from failure or malfunction of the AEB system’s control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.
A1124002073917_1
This bulletin provides information for when there is a fluid sample request from Product Support.
A0024852021205_8
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
A872474202012414
This bulletin provides information when the air conditioning is no longer operative; DTC 00457, 00256, 01592.
A9024842032113_9
This bulletin provides general information regarding outside air temperature readings.
A9624962027416_7
This bulletin provides information when the sunglass holder will not close or is stuck closed.
A9024832059335_5
This bulletin provides information when there is noise from around the instrument cluster.
A9424762073332_2
This bulletin provides information for when there is noise when steering.
A2724712067906_5
This bulletin provides information for when DTC P0A7D00 is stored.
A5724342017082_1
This bulletin provides information when the remote control key is inoperative.
A0024842073507_1
This bulletin provides instructions on evaluating TDI vehicles for repurchase prior to repairs.
A9424742073332_1
This bulletin provides information if there is noise when steering the vehicle.
A9424722073282_1
This bulletin provides information on visual concerns with the headlight lens.
A4824602073033_1
This bulletin provides information for when the steering column adjustment does not work.
A4824612034351_1
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
AWA 24-01
This Document informs dealers on the new oil consumption & piston fracture warranty extension for 2012 A4, A5, A6, Q5 & TT / 2013 A4, A5, A6, Q5 & TT / 2014 A4, A5, A6, Q5 & TT / 2016 A3 & TT / 2017 A3 & TT vehicles
A9124632044694_3
This bulletin provides information pertaining to MMI Navigation database concerns.
A7024872038029_9
This bulletin provides information for when there are noises from the headliner/sunroof area.
DC_Closure 19N8
SERV_ACT - After-Run Coolant Pump - Closure Notice
A0023822047812_7
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via the Mirror Server.
A9023672072568_1
This bulletin provides information for when the lane change assist radars cannot be calibrated after replacement.
A912306202432310
This bulletin provides information when the parking assistance provides false warnings.
A4523362072304_1
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
A9023562032113_8
This bulletin provides general information about the outside air temperature reading.
A6623042030471_7
This bulletin provides information for when the license plate mounting bracket threaded inserts are stripped.
A0023812070568_2
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
SM 56-2023
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A9423672071954_1
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
A7423262071893_1
This bulletin provides damage assessment guidelines for textile seat covers.
A0023762071721_1
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans (Ghost faults).
A0123812028842_4
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
A0023742052680_4
This bulletin provides information on the additional reporting requirements for safety related inquiries.
A0023732061669_2
This bulletin provides information on workshop mode with Audi connect vehicles.
A0023712070568_1
This bulletin provides information on professional noise analysis with the VAS 611 015 PICO NVH Tool.
A9123262071264_1
This bulletin provides information for when the customer has concerns about the navigation route guidance.
A6423922020552_1
This bulletin provides information for when exterior glass cleaning is needed.
A8723452041717_9
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
A9023322059335_4
This bulletin provides information for when there is noise from the area around the instrument cluster.
A922336203815115
This bulletin provides information for when the washer solvent level warning is on.
A4623452070679_1
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29.
A4823412028220_1
This bulletin provides information for instances where the steering wheel leather is damaged.
A102326201828810
This bulletin provides information on checking for debris when replacing an engine.
A8723442010146_8
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
A9123062010146_8
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
A9423652061922_3
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and taillights.
A5723082027406_5
This bulletin provides information regarding the Audi advanced key.
A922335203815114
This bulletin provides instructions for when the washer level warning is on but the reservoir is full.
A0023702021205_7
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
A0023692031473_4
This bulletin provides information for when car wash bristles become stuck in the body gap between the headlight and fender.
A912394201818713
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference.
A9423632061922_2
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty submissions.
A4423992056386_9
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4423982056386_8
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4623432069904_1
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
A9023222032113_7
This information bulletin contains a background on the outside air temperature reading.
A192336202530314
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
A6423882047061_5
This bulletin describes the process to clean sticker residue from the windshield.
SM 18-2023
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4023512023187_7
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and repair is not needed.
A402352202431813
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9123832037809_1
This bulletin provides information on how to update the navigation map.
A9623822056019_2
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored.
A462341203418123
This bulletin provides instructions for brake noise analysis and handling.
A012341201475312
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A9223332038151
This bulletin provides instructions for when the washer solvent level warning is on in the DIS but the washer solvent level is correct.
DC_Alternator_6
Support for Customers Affected by Alternator Back-order
A6423862047061_4
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production.
A6623942049680_2
This bulletin provides instructions for when the exterior trim has spots.
A4423972022563_2
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph.
DC_Alternator_4
Support for Customers Affected by Alternator Back-order
DC_Alternator_5
Support for Customers Affected by Alternator Back-order
A8023122062583_2
This bulletin provides instructions for when the customer advises that there is insufficient or uneven cabin heating from the HVAC system.
DC_Alternator_3
Support for Customers Affected by Alternator Back-order
A9123592036576_7
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s).
A4623402069078_1
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
DC_Alternator_2
Support for Customers Affected by Alternator Back-order
DC_Alternator
Support for Customers Affected by Alternator Back-order
DC_RECALLS
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
A572200202203210
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A1922332061604_5
This bulletin contains instructions for resolving a coolant leak.
DC_TDIReminder
TDI Reminder message
DC_TDI_repairs
Dealer Communication: IMPORTANT: Evaluate TDI Vehicles for Repurchase Prior to Repairs
A0022582045316_6
This bulletin contains information for diagnosing the Start/Stop system.
A462234203418122
This technical service bulletin provides troubleshooting for brake noise.
A4822342065978_2
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly.
Circular69DLREV1
Special Parts Collection - Head Curtain Airbag - GFF labor operation updated in the claiming instructions
A922230203815112
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A642285202055211
This bulletin provides instructions on how to properly clean exterior glass.
Circular 69DL
Special Parts Collection - Head Curtain Airbag
Dealer 69DL
Special Parts Collection - Head Curtain Airbag
SM 48-2022
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4622332051095_7
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462232203418121
This technical service bulletin provides troubleshooting for brake noise.
44133820344451
Message "TPMS" in dash insert
A4522262067132_1
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs.
A442292202256321
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A8722272041717_8
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A872225201014617
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation system.
A402238202431812
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
A9022572032113_6
This is an informational bulletin containing information about the outside temperature reading.
A9022582059335_3
This bulletin contains information on noises from the instrument cluster installation area.
A462230203418120
This technical service bulletin provides troubleshooting for brake noise.
A402237202431811
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
DC_20220329
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
A9122892037809_9
This informational bulletin contains instructions about updating the navigation map.
A1722172060750_3
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A4622282051095_5
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A012216203300126
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9122752024323_9
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A442287202256320
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A462226202258411
This informational bulletin provides diagnostic information for brake conditions.
A462227203418119
This technical service bulletin provides troubleshooting for brake noise.
A192228202530313
This bulletin contains instructions for identifying and mixing factory fill coolants.
A192227202530312
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4421862056386_7
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4021302023187_6
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or maneuvered.
A4021312024318_1
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A002155201173212
This bulletin contains general instructions for software updates.
A4421842065160_1
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
DC 20210928
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
A9121342018187_1
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A012111203300125
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A8721162041717_7
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A0121102028842_3
This informational bulletin gives instructions for identifying chip tuning.
A4821092028220_9
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty.
A4421832056386_6
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
148520367612
The oil pressure switch is defective.
A1921222046712_3
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A2021352043357_1
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A0021482021205_6
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
A0021472031473_3
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again.
SM 46-2021
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A4821052063527_1
This bulletin contains instructions for calibrating the steering angel sender G85.
SM 44-2021
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
AWA 21-03
This Document informs dealers on the new electromechanical steering unit warranty extension for 2012-2015 Model Year Audi B8 (A4, Q5 & SQ5) and C7 (A6) Vehicles
147920333793
An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced.
A1921182061604_4
This bulletin contains instructions for resolving a coolant leak.
A9121042024323_8
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0021442052680_3
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage).
A1021222018288_9
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
A9021032058077_5
This bulletin contains instructions for determining unexpected Audi presense interventions.
A1721162060033_3
This bulletin contains repair instrructions for when there are noises in the engine compartment with DTC P052E00.
A4421822056386_5
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A6421802020552_1
This bulletin provides instructions on how to clean exterior glass.
A8721132010146_1
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
ELSAallignAudi
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
A9021002032113_5
This information bulletin contains a background on the outside air temperature reading.
AWA 21-04
This Document informs dealers on the new turbo warranty extension for 2013-2016 A4, 2013-2017 A5/Q5, and 2012-2015 A6 vehicles
A4021242016453_4
This bulletin contains instructions for determining if bushings need to be replaced.
A9021982059335_2
This bulletin contains information on noises from the instrument cluster installation area.
A6421792047061_3
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A7021722038029_8
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A1921152061604_3
This bulletin contains instructions for resolving a coolant leak.
A5721752022032_9
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A9121862062713_1
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
A8021112062583_1
This bulletin contains instructions for addressing an insufficient or uneven heating performance from the HVAC system.
A9421362023322_3
This informational bulletin contains information on the different shading of LED headlights.
A1321132062387_1
This bulletin contains instructions for determining if a repair is needed when coolant touches a poly V-belt and/or a toothed belt.
A1921142061604_2
This bulletin contains instructions for resolving a coolant leak.
A9121762037809_8
This informational bulletin contains instructions about updating the navigation map.
A4621252054385_2
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill).
A4421802056386_4
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4621222051095_4
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462123202258410
This informational bulletin provides diagnostic information for brake conditions.
A462124203418118
This technical service bulletin provides troubleshooting for brake noise.
A4421792022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A6621692030471_6
This informational bulletin covers the condition of when license plate mounting bracket threaded inserts are stripped.
A9421332061922_1
This informational contains instruction on how to document optical concerns for warranty claims.
A1721122060750_2
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A2321562059205_2
This bulletin contains information on when to submit a TAC ticket for DTC P220100 with various DFCC codes.
A9121642024323_7
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A5520512014055_8
This bulletin contains instructions for addressing discoloration due to moisture on a new vehicle.
A9120572036575_6
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
SM C-2020
This special notice is to inform dealers to return the part numbers listed (State of California only).
A1920102061604_1
This bulletin contains instructions for resolving a coolant leak.
A0020432061669_1
This informational bulletin contains instructions for Audi connect before performing any MMI work.
2010-2021EngOil
Added Saga Part number for 0W40 oil: SAGA Part: G E55040S0
A012093203300124
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9120242026611_7
This bulletin contains a guide for troubleshooting HD radio issues.
A0020422045316_5
This bulletin contains information for diagnosing the Start/Stop system.
A1720112060750_1
This bulletin contains instructions for using the UV additive to find engine oil leaks.
EmailAUTDI2L-3L
Reminders - TDI Approved Emissions Modifications, Emissions Compliant Repairs, corrections and extended warranty / warranty policy and loaner vehicle overview
21AUTIRECHAINS
Added new graphic to reflect where to find MY 21 information
A0120882033001_2
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A9120112037809_7
This informational bulletin contains instructions about updating the navigation map.
A9020652032113_4
This information bulletin contains a background on the outside air temperature reading.
A1720102060033_2
This bulletin contains repair instrructions for when there are noises in the engine compartment with DTC P052E00.
Audi Part Labels
Recall Reminder Part Labels
A1720072060033_1
This bulletin contains repair instructions for when there are noises in the engine compartment with DTC P052E00.
A1720082060259_1
This bulletin contains repair instructions for when DTC P052E00 is stored with noise coming from the engine compartment.
A012072203300122
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A3720012039650_2
This bulletin contains instructions for addressing a leak from the transmission oil pan gasket or transfer case.
A1720062028440_5
This informational bulletin explains when the range display is empty in the on-board computer.
A1920042025303_1
This bulletin contains instructions for identifying and mixing factory fill coolants.
A0020382039206_3
This informational bulletin contains instructions on how to use the QR code in a TSB.
A9120732026390_7
This bulletin contains instructions for correcting the phonebook.
A9120702044694_2
This technical service bulletin provides troubleshooting for issues with the navigation map database.
A4020052024318_9
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9120652036576_6
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
A6420742020552_9
This bulletin provides instructions on how to clean exterior glass.
A012062203300121
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A0020372059437_1
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing some issues.
A9320272032889_3
This bulletin provides repair instructions for when the electric drive mode cannot be activated.
A872005201014615
This bulletin contains instructions for properly cleaning and removing a musty odor in the vehicle.
A9020442032113_3
This information bulletin contains a background on the outside air temperature reading.
A9020452059335_1
This bulletin contains information on noises from the instrument cluster installation area.
SM 25-2020
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
A0020362002047_1
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
A012058203300120
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A2320542059205_1
This bulletin contains information on when to submit a TAC ticket for DTC P220100 with various DFCC codes.
A6420722047061_2
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A012054201475311
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A942020201780613
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A5120132009967_1
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A012046201475310
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A912039201818711
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
Circular19N8REV1
SERV_ACT - After-Run Coolant Pump - Updated claiming and work instructions: A single part number per criteria will now be used.
A4420732056386_3
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A9420192058420_1
This bulletin contains instructions for verifying if there is outside influence or if the technician should carry on with standard diagnosis.
A921924203815111
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A0019292031473_2
This informational bulletin contains instructions for when car wash bristles are stuck in the headlights. 2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant
20AUTIRECHAINS
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
AWA 19-06
The communication contains the details of the water pump extended warranty.
A9219232038151_1
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct. 2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant
145320381292
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A7019682038029_7
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
SM 95-2019
The part number listed in the document are to be returned.
A9119032041430_7
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A1919992052657_3
This informational bulletin contains details on conditions for replacing the water pump and/or thermostat housing. 2015-2019 A3 Cabriolet, 2017-2018 S3 Cabriolet, 2018-2019 A5 Sportback, S5 Sportback, 2013--2019 TTR
A4819822034351_9
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A4019972018194_9
This bulletin contains repair instructions for leaking shock absorbers.
A0019272045316_4
This bulletin contains information for diagnosing the Start/Stop system.
SM 80-2019
Parts are currently blocked from sale at this time.
A0019262052680_2
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage.
ATUBody2019
Body components - Examples of customer misuse
A9119922041430_6
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A9119932037087_4
This bulletin contains instructions for enabling text message notifications through the MMI system.
A0019252011732_1
00 Software Version Management (SVM), operating instructions
A9419132017806_1
This bulletin contains information regarding when the message 'Vehicle lights: malfunction' appears with DTC 03280, 01800, or B126AF0.
A9119882024323_6
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0119252055816_2
This bulletin contains repair instructions for DTCs P007000 and P208000.
A1719982028440_4
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
A9619432056019_1
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off. Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
AWC 19-05
This communication is issued to inform dealers of updated shipping regulations related to lithium ion batteries.
Circular 26L9
Exhaust Gas Recirculation (EGR) Cooler
Dealer 26L9
Exhaust Gas Recirculation (EGR) CoolerÂ
Circular 23Z8
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Additionally, to reduce soot accumulation affecting the oxygen sensor, it is necessary to replace and relocate the sensor, which requires replacement of the diesel oxidation catalyst (DOC) and diesel particulate filter (DPF).
SM F-2019
The part number listed in the document are to be returned if it meets the criteria provided.
A0119212055816_1
This bulletin contains repair instructions for DTCs P007000 and P208000.
Dealer 23Z8
Audi is releasing a software calibration update to the Approved Emissions Modification (AEM) to improve on-board diagnostics (OBD) monitoring of vehicle emissions systems and provide other improvements to the software used by the vehicle. Additionally, to reduce soot accumulation affecting the oxygen sensor, it is necessary to replace and relocate the sensor, which requires replacement of the diesel oxidation catalyst (DOC) and diesel particulate filter (DPF).
AWC 19-04
This communication is issued to remind dealers of the repair validation process for repair group 19. 2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8
A011919203300119
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A4819792028220_8
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe
A2319512036668_5
This informational bulletin contains diagnosis instructions for the N290 fuel metering valve. TDI ONLY
A0019222047812_6
This informational bulletin contains instructions for setting up and using the SD Creator program. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A8719912041717_6
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements. 2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster
A9019192032113_2
This information bulletin contains a background on the outside air temperature reading. 2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe
A9119652050565_2
This bulletin contains general software update instructions for vehicles with PR Code 7UH. 2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster
A0019212052680_1
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe
A201918204335711
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A6019302055255_1
This informational bulletin contains specs for the new sunroof lubricant.
A201916203507314
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.
A9419062032184_8
This bulletin provides troubleshooting instructions for LED Daytime Running Lights.
AWA 19-02
This bulletin clarifies how to claim AdBlue on warranty claims.
Circular - 19N8
After-Run Coolant Pump
Dealer - 19N8
After-Run Coolant Pump repair available.
A201913203507313
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM. Vehicles also include 2015 A3 Cabriolet and 2012 RS7,
A011913 20353688
This bulletin contains repair instructions for when a MIL is on with DTC P203B00.
A571954 20220328
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A961934 20489272
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A201911 2043357
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A011902 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A921916 2038151
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A441969 2022563
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A461903 2034181
This technical service bulletin provides troubleshooting for brake noise.
A001915 2047812
This informational bulletin contains instructions for setting up and using the SD creator program.
A011999 2033806
This bulletin provides repair instructions when coolant control valves have coolant inside of their electrical connector.
19N4 19O2
This news email tells dealers when to perform 19N4 or 19O2
AWC 17-34
This communication instructs dealers to contact the Technical Assistance Center if they encounter a MIL on before performing the TDI emissions modification. - REVISED 12/17/18 to apply to 3.0L models and to remove 2.0L models.
AWC 18-14
This communication notifies dealers that AWC 17-34 was modified to remove 2.0L vehicles and apply to 3.0L vehicles only.
A011894 2033001
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A911821 2051527
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A011893 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A001814 2045316-
This bulletin contains information about the Start/Stop system.
A401887 2035854-
This bulletin contains repair instructions for when a rattle or knocking noise is head when driving over bumps and the vehicle has 75mm hydro-bushings.
TDI Repair and I
Email TDI Repair and IN-FORM Tool Enhancement
Campaign Parts B
3.0L TDI Emissions Recalls 23R8 Part supersession
A461897 2042182-
This bulletin provides information on diagnosing and fixing a brake squeak that occurs in specific conditions: first brake, below 20MPH, below 40 degree F, and in high humdity.
Communication 19
Communication Toolkit for Dealers
A011879 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
AWC-18-09
This communication provides instructions for documenting the fuel refill in the INFORM tool.
Email Audi TDI C
Email-Audi TDI-Customer Modificaion Amenities
AWC 18-07
This communication serves as a reminder that dealers are to check for pre-existing conditions for all Generations of 2.0L TDI and 3.0L TDI resale, buyback, TDI Direct, and VCI auction vehicles prior to proceeding with the AEM Emissions Recall. Only create an Audi Technical Assistance Center (TAC) ticket if required by applicable recall.
AWA-17-12
For Audi 3.0 L TDI Generation 2.1 SUV vehicles repaired by the emissions modification recall, the following warranty extension is applicable. ?Extended Emissions Warranty? Limited Warranty Extension The Limited Warranty Extension is applicable to 3.0L TDI vehicles Generation 2.1 SUV with engine code CNRB.
AWA-18-01 201806
This bulletin explains the extended emissions warranty for TDI vehicles modified under Campaign 23V4. The parts list was updated to include service numbers.
A011875 2035368-
This bulletin contains repair instructions for when a MIL is on with DTC P203B00.
A911800 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
A911899 2051527-
This informational bulletin contains instructions for when the Sirius presets are missing with no DTCs.
Email-Audi 3.0L
Dealer Communication: 3.0L TDI Trade-In Issue Resolution
Circular - Emiss
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations. Removed California DMV Tie-in Requirements
A911895
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
A911895 2026657-
This bulletin contains instructions for removing the HD radio feature if requested by the customer.
Email-Audi AEM T
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement
Email-TDI Virtua
TDI Virtual Closing Resources
A701866 2038029_
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
Email-2.0L TDI a
2.0L TDI and 3.0L TDI Extended Emissions Warranty On-Board Diagnostic (OBD) System Coverage Questions
AWC-18-05
This communication asks dealers to contact Audi Warranty if they have any questions about the extended warranty coverage for 2.0L and 3.0L TDI vehicles.
Email-AdBlue par
This email clarifies which part numbers dealers can use for refilling AdBlue.
Email-2.0L & 3.0
Email-2.0L & 3.0L TDI AEM ECR Replacement Labels
AWA-18-05
This communication provides coding instructions for AdBlue refills after the AEM is performed.
A911870 2041430_
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A971860 2036764_
This bulletin contains repair instructions for when the vehicle will not start and DTC P068A00 is stored.
AWC 18-04
This communication is a reminder to dealers that they must refill vehicle fuel tank after AEM.
A231745 2049856-
This bulletin contain repair instructions for the TDI emission modification.
AWA-17-17
This communication provides instructions for claiming "delight elements " for repairs related to recalls 80C5 and 80C6.
A961721 2048927-
This informational bulletin contains instructions for minimizing the risk of an unintentional opening of the trunk lid with the remote.
A011748 2040403-
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored.
A911760 2040406
This bulletin contains instructions on a repairing an issue when the GPS does not have the correct location or reception.
A001702 2035505
This repair authorization is for special VINs that are part of the Audi on Demand and Audi at Home program.
A461779 2042182-
This bulletin provides information on diagnosing and fixing a brake squeak that occurs in specific conditions: first brake, below 20MPH, below 40 degree F, and in high humdity.
A511711 2009967-
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A911750 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
Maint Flip Chart
Revision to Tires-rotate: 5K only; added "(except R8)"
A911745 2030465-
This technical service bulletin provides troubleshooting tips for various issues with the MMI3G+ functionality.
A911743 2042097-
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI navigation.
A201796 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A011732 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A001799 2045316-
This bulletin contains information about the Start/Stop system.
A011730 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A461776 2042182-
This bulletin provides information on diagnosing and fixing a brake squeak that occurs in specific conditions: first brake, below 20MPH, below 40 degree F, and in high humdity.
SM 52-2017
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation 14s.
e-mail - Audi 3.
3.0L TDI Trade-In Issue Resolution.
A201795 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A941791 2012749-
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
A911736 2024323-
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A941789 2036670-
This bulletin contains repair instructions for when the high beam light is inoperative but the low beam is functioning with DTC 003205 or 003206.
A201794 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201792 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401774 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A191789 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A911733 2021780-
This informational bulletin contains procedure information for DTC 00468 with error messages on the radio display.
A401770 2018194-
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
A401768 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
Email - 2.0L and
2.0L & 3.0L TDI Settlement Updates
SM 44-2017 EN
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward.
Email-3.0L TDI U
3.0L TDI Update - Claim Processing Appointments
A461772 2047830
This informational bulletin contains instructions for proper brake maintenance.
A201790 2043758
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A401766 2024318
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
e-mail 3.0L TDI
e-mail communication for 3.0L TDI Update - Claim Processing Appointments
A481774 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A201789 2043758-
This bulletin instructs the reader to diagnose issues with fuel pressure and to replace the fuel delivery unit with the new kit if the correct DTC and symptom code combination is present.
A441764 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A011715 2047785-
This is an informational bulletin requesting that dealers with the V6 TDI engine call TAC for instructions when they receive one of six DTCS in conjunction with DFCC symptom codes between 19184 and 19189.
A171782 2010043-
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil change.
A301722 2019850-
This technical service bulletin provides guidelines for diagnosing the clutch plate.
A011713 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A011712 2047707-
This informational bulletin provides instructions for when DTC P195000 appears but there is no customer concern.
A001791 2045316-
This bulletin contains information about the Start/Stop system.
E-mail-3.0L TDI
3.0L TDI Settlement Program Update
A911724 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
A401761 2024318-
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A481772 2034351-
This bulletin contains repair information for when there is a creaking/squeaking from the steering column when steering slowly.
A571740 2047432-
This bulletin contains repair information for when the remote key has low range or the functions do not work. This is for all keys and there is no relevant DTCs stored.
A911719 2023006-
This informational bulletin contains repair instructions for when the parking aid system does not work.
A231740 2036668-
This informational bulletin contains diagnosis instructions for the N290 fuel metering valve.
A201788 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A571738 2017082-
This informational bulletin contains instructions for sychronizing the remote key after the battery has been disconnected or replaced.
Edition76
Technical bulletins and updates
AWC-17-13
This communication asks technicians to call TAC before performing Recall 69P1 if Warranty Key U98 is present.
SM 19-2017 EN
This special notice is to inform dealers to return all part numbers listed and order successor part numbers going forward.
A191779 2036852-
This informational bulletin provides a clarification on a normal operation for the cooling fans.
Bosch Class Acti
Bosch Class Action Communication - Audi
Updated Bosch Cl
Bosch Class Action Communication - Audi
ATE-17-05
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
Email - Audi 3.0
This is an email covering the 3.0L TDI terms of the settlement. It gives you links that cover FAQs avout the settlement.
A011703 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A661761 2038652-
This technical service bulletin provides repair instructions for paint flaking off the radiator grille or front license plate holder.
A011701 2033001-
This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A701756 2038029-
This bulletin contains repair instructions for various squeaks and/or rattles that are heard from the roof area on vehicles equipped with pananormic sunroof.
A191777 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A461764 2042182-
This bulletin provides information on diagnosing and fixing a brake squeak that occurs in specific conditions: first brake, below 20MPH, below 40 degree F, and in high humdity.
A701755 2039023-
This tehcnical bulletin provides instructions on how to remove various squeaks and rattles in the front and rear doors.
A931702 2032889-
This bulletin provides repair instructions for when the electric drive mode cannot be activated.
A931703 2046620-
This bulletin provides repair instructions for setting the mixture adapation values.
A201785 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201784 2043357-
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A911700 2041430-
This technical service bulletin provides instructions for replacing the rear camera wiring harness.
A371672 2040747_
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR MODIFYING THE VOLTAGE SUPPLY OF THE GEARBOX TERMINAL 30.
AWA1609
This is a general communication notifying dealers that there is extended Warranty coverage available for the exhaust gas temperature sensor for certain models and model years. This document details the terms of the warranty extension.
A201683 2043357_
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A151631 2045732_
THIS BULLETIN PROVIDES INFORMATION ON REMOVING A DAMAGED SCREEN FROM THE NON-RETURN VALVE.
A911693 2028141_
THIS BULLETIN PROVIDES SOFTWARE UPDATE INFORMATION FOR THE MMMI 3G OR RMC FOR NAVIGATION DATA.
A921614 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A011691 20459981
This bulletin provides software update instructions to correct a EGR slow response in the engine control module.
A011691 2045998_
THIS BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO CORRECT A EGR SLOW RESPONSE IN THE ENGINE CONTROL MODULE.
A011689 2040962-
This bulletin provides information for a hardware and software update for TDI clean diesel vehicles with DTC P20E800.
A011688 2040403-
This technical service bulletin instructs the reader to replace either a combi valve or vacuum solenoid valve depending on the circumstances under which DTC P244000 and/or P244200 were stored.
A871679 2041717-
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan.
A911690 2036575-
This informational bulletin provides an explanation for the customer regarding known software issues with the MIB & MMI3G+ bluetooth security profile.
Email - Audi TDI
This email gives an update on the consumer settlement program with regards to 2.0L and 3.0L TDI vehicles.
A011685 2041120-
This bulletin provides information regarding a software update for DTC P042000 and/or P043000.
A151630 2045732-
This bulletin provides information on removing a damaged screen from the non-return valve.
A441662 2010334-
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
A441663 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A661657 2038652-
This technical service bulletin provides repair instructions for paint flaking off the radiator grille or front license plate holder.
Email - TDI Comp
This email gives an update on the current emissions issues with regards to 2.0L and 3.0L TDI vehicles.
A921613 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A011680 2033806-
This bulletin provides repair information when coolant control valves have coolant inside of their electrical connector.
A921612 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A001684 2037949-
This technical bulletin provides instructions for an an error message and updating with an SVM code.
A911682 2045580-
This bulletin provides information regarding a data connection message dur to the SIM card for T - Mobile subscribers.
A911681 2040406-
This bulletin contains instructions on how to fix when the GPS does not have the correct location or reception.
A911677 2044940-
This technical service bulletin provides software update instructions to fix an issue that prevents Google Earth from loading.
A4616512040942
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING FOR BRAKE SQUEAL CONCERN.
A4616542042182
THIS BULLETIN PROVIDES INFORMATION ON DIAGNOSING AND FIXING A BRAKE SQUEAK THAT OCCURS IN SPECIFIC CONDITIONS: FIRST BRAKE, BELOW 20MPH, BELOW 40 DEGREE F, AND IN HIGH HUMDITY.
24CO
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. AS A RESULT, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY COME ON EVEN THOUGH THE CATALYTIC CONVERTERS ARE WORKING PROPERLY. IF THE MIL IS ON, A VEHICLE WILL NOT PASS AN EMISSIONS INSPECTION.
A37166820300075
THIS BULLETIN PROVIDE INSTRUCTIONS FOR WHEN THERE ARE HARSH GEAR SHIFTS BUT THERE IS NO FAULTS STORED AND YOU CAN DUPLICATE THE CONCERN.
EMAIL UPDATE
THIS EMAIL GIVES AN UPDATE ON THE CONSUMER SETTLEMENT PROGRAM WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A91167120404066
THIS BULLETIN CONTAINS INSTRUCTIONS ON HOW TO FIX WHEN THE GPS DOES NOT HAVE THE CORRECT LOCATION OR RECEPTION.
A94168020321847
THIS BULLETIN PROVIDES TROUBLESHOOTING INSTRUCTIONS FOR LED DAYTIME RUNNING LIGHTS.
A20167620437584
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A911667 2030465-
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A911667203046510
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A011673 2040403-
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
A01167320404033
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
82B8 CIRCULAR
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
A20167520437583
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A66165520386525
THIS TECHNICAL SERVICE BULLETIN PROVIDES REPAIR INSTRUCTIONS FOR PAINT FLAKING OFF THE RADIATOR GRILLE OR FRONT LICENSE PLATE HOLDER.
82B8
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
82B8 DEALER LETT
ON AUDI VEHICLES WITH AUXILIARY AIR HEATER (PTC ELEMENT) MANUFACTURED WITHIN A SPECIFIC PERIOD, THE HEATING PERFORMANCE MAY DECREASE OVER TIME.
A01166820404914
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INSTRUCTIONS TO RESOLVE A COOLANT WARNING AND STORED DTC.
A9116612044940-1
THIS TECHNICAL SERVICE BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO FIX AN ISSUE THAT PREVENTS GOOGLE EARTH FROM LOADING.
A91166120449401
THIS TECHNICAL SERVICE BULLETIN PROVIDES SOFTWARE UPDATE INSTRUCTIONS TO FIX AN ISSUE THAT PREVENTS GOOGLE EARTH FROM LOADING.
A19167220431422
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE THE AUXILIARY COOLANT PUMP IF CERTAIN DTCS ARE STORED.
A94167920438302
THIS TECHNICAL SERVICE BULLETIN PROVIDES A REPAIR WHEN THE CORNERING LIGHTING IS NOT WORKING ON ONE SIDE.
A46164120409422
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING FOR BRAKE SQUEAL CONCERN.
A9116562040406-5
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
A91165620404065
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE VEHICLE'S ACTUAL LOCATION.
2014 Q5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A40165520243184
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR CORRECTING A CLICKING SOUND FROM THE WHEEL BEARING(S).
EMAIL TDI UPDATE
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A57162620220327
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING INFORMATION FOR THE VEHICLE LOCKING SYSTEM.
A91164720304658
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
A91164820414303
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE REAR CAMERA WIRING HARNESS.
A91164920304659
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING TIPS FOR VARIOUS ISSUES WITH THE MMI3G+ FUNCTIONALITY.
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A201671 20437582
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE COOLANT THERMOSTAT WITH A NEW PART NUMBER TO RESOLVE A STORED DTC.
A101613 2044546-
THIS TECHNICAL SERVICE BULLETIN PROVIDES INFORMATION ABOUT LOCATING THE SOURCE OF AN OIL LEAK AND HOW TO PROCEED WITH A REPAIR.
A17167520381197
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A4416612034445
THIS TECHNICAL SERVICE BULLETIN NOTIFIES THE READER THAT IF THE TPMS MESSAGE APPEARS BRIEFLY AFTER THE ENGINE IS STARTED AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM.
A46163920421823
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING BRAKE PADS TO PREVENT A NOISE.
A20167020433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A2016720433572
THIS TECHNICAL SERVICE BULLETIN PROVIDES A SOFTWARE CODE FOR CORRECTING AN ISSUE THAT CAUSES DTC P046100.
A24165420440032
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
EMAIL - TDI UPAT
THIS EMAIL GIVES AN UPDATE ON THE CURRENT EMISSIONS ISSUES WITH REGARDS TO 2.0L AND 3.0L TDI VEHICLES.
A96160720295633
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A01166220404032
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
A15162820399952
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO VERIFY A RATTLING NOISE HEARD AT COLD START AND TO REPLACE BOTH UPPER CHAIN TENSIONERS OF BANK 1 AND BANK 2 WITH AN OPTIMIZED PART.
A17167220381196
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A37166320407472
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR MODIFYING THE VOLTAGE SUPPLY OF THE GEARBOX TERMINAL 30.
A20166720433571
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO UPDATE THE ECM SOFTWARE TO RESOLVE AN ISSUE THAT CAUSES DTC P046100.
A17167120381195
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR AND REPLACE A DEFECTIVE OIL LEVEL SENSOR.
A96160620295632
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A24165320440031
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND REPAIR ISSUES WITH THE INTAKE MANIFOLD FLAP VALVE N316.
A91163920420133
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC.
A20166620437581
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A46164720421824
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING FOR A SQUEAL SOUND FROM THE FRONT BRAKES.
A94167620438301
THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE BOTH HALOGEN BULBS FOR CORNERING LIGHTING WHEN THE CORNERING LIGHTING DOES NOT WORK ON ONE SIDE.
CUSTOMER LETTER
LETTERS TO CUSTOMERS EXPLAINING THAT THE REGISTRATION PERIOD FOR THE TDI GOODWILL PACKAGE FOR THE 3.0L TDI HAS BEEN EXTENDED.
EMAIL - TDI INFO
EMAIL TO DEALERS EXPLAINING THAT THE REGISTRATION PERIOD FOR THE TDI GOODWILL PACKAGE FOR THE 3.0L TDI HAS BEEN EXTENDED.
A20166420438921
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V6 ENGINES.
A20166520415947
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH 4-CYLINDER ENGINES.
A46163320421822
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO REPLACE BRAKE PADS WITH A SQUEAL COMPLAINT WITH A NEW PART NUMBER AND HOW TO UPDATE THE SOFTWARE OF THE ABS/ESP TO DISPLAY A NEW PR CODE AFTER REPLACEMENT.
A011656 2040491-
The technical service bulletin is in regards to the MIL being on due to DTC P1B1C00 (coolant pump mechanical malfunction) being stored in the ECM. "Coolant System: Fault Turn Off Engine" and the Coolant symbol appear in the information panel. Condition can be caused by a defective thermostat or the diagnostic software is incorrectly displaying the warning.
A461631 2042182-
Customer reports hearing a squeal noise from the front brakes during first brake application in the morning, with cold brakes, below 20 mph, below 40 ºF, and high humidity.
A481669 2034351-
Customer may report hearing creaking or squeaking noise from the steering column when steering slowly. The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead.
A481668 2043629-
Steering angle sensor cannot be programmed. The steering angle sensors cannot be calibrated and the steering end stops cannot be adapted on a vehicle with dynamic steering.
A441660 2034445-
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. This occurs after the engine is started, the message "TPMS" appears briefly and then turns off. There are no DTCs stored.
A171668 2038119-
The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level. There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A191667 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
Dealer Letter -
Effective immediately, the codes for the STP4 (2.0L TDI) and STP5 (3.0L TDI) actions will show the campaign code 23Q4 (2.0L TDI) and 23R8 (3.0L TDI) only on the Inventory Vehicle Open Campaign/Action Report. Elsa and ServiceNet will continue to display them as STP4 (2.0L TDI) and STP5 (3.0L TDI).
A661546 2030471-
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped.
A961604 2042811-
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting. The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. The Audi connect Gen1 system includes all vehicles that utilize a removable plastic SIM card. The Audi connect Gen2 system includes all vehicles that utilize an embedded SIM card. The root cause of all complaints cannot be attributed to the vehicle hardware because of the backend server configurations that need to be correct in order for Audi connect to work. For most sporadic complaints, the issue typically resides with the MBB backend server or with the source data provider (Google, INRIX, etc.), and not with the vehicle. In rare cases, the mobile network operator (AT&T, T-Mobile) can be the cause of the complaint. For most static complaints, the issue can be attributed to the user account subscription or possibly the vehicle hardware.
A461628 2040134-
Brake noise (without hybrid)_2.0T with PR-1LB. Customers hear a squeal from the front brakes during first brake application in the morning with cold brakes below 20 mph, below 40ºF, and with high humidity.
A191666 2043142-
The MIL is sporadically on. One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
Elsa Newsletter
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition.
A011652 2040491-
MIL on (DTC P1B1C); message in information panel: "Coolant System: Fault Turn Off Engine" The condition is caused either a defect with the thermostat (in model year 2012 and 2013 vehicles) or The diagnostic software is incorrectly displaying the warning. No technical issue exists. Solutions are an improved thermostat installed in production and the diagnostic software has been updated.
A191665 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A011649 2041120-
The MIL is on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. New ECM software implemented to correct the condition.
A401549 2018194-
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A911529 2013422-
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A001578 2021205-
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement.
A171568 2028440-
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A201559 2011703-
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.
155820415945
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A911526 2042097-
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.
A401548 2042603-
When the vehicle is driven between 35 mph and 75 mph, a noise can be heard in the front of the vehicle. The customer may say that the noise is coming from the steering column area, and may describe the sound as buzzing, humming, whistling, whining, grinding, howling, and/or droning. The best way to understand the complaint is to discuss it with the customer. Faulty wheel bearing(s) may cause the noise.
A571517 2035173-
Supersedes Technical Service Bulletin Group 57 number 13-98 dated December 9, 2013. Customer may report that the automatic door lock function cannot be deactivated. The ?Lock when driving? (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door.
A241551 2038212-
Supersedes Technical Service Bulletin Group 24 number 14-50 dated August 28, 2014. The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
155620415944
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201556 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-55 dated November 6, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
2613202026757 2
An AdBlue message may appear in the instrument cluster either because there is a fault in the
A911524 2026611-
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The
A911528 2042013-
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. The following message appears in the MMI: ?This service is currently unavailable. Please try again later.? The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Additionally, if the vehicle is a model year 2016 A6, A7, or TT, the customer may not be able to see speed and flow traffic information in the navigation map screen, and may consistently see that no traffic reports are available. For these vehicles, traffic is provided by INRIX online.
155520415943
Fuel level sensor, circuit range/performance - The ?check engine light? might illuminate with DTC P0461 stored in the engine control module. No engine-related problems are present, and the vehicle is safe to drive.
A201555 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-50 dated October 19, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM).
A571516 2024111-
Supersedes Technical Service Bulletin Group 69 number 12-22 dated February 13, 2012. After the comfort system central control module, J393 (address word 05) is replaced, the control module cannot be coded via SVM spec/actual. Any time a comfort system central control module, J393 (address word 05), is replaced, the new control module must be coded and parameterized with online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then an SVM code is required to code and parameterize the new control module. The SVM code can be found in Parts Bulletin 9-101, which can be found on the etkainfo.com web site.
A201554 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A201552 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A511510 2009967-
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing.
A461525 2022584-
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.
A201550 2041594-
Supersedes Technical Service Bulletin Group 20 number 15-47 dated August 5, 2015. The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A571514 2042249-
In cold conditions (under 40°F), the vehicle sporadically cannot be locked or opened with the entry and start authorization. No DTCs related to the entry and start authorization control unit are logged. The issue occurs with all keys. The vehicle can be locked and opened with the remote. The conductivity of the door handle is affected by external influences.
A911522 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-10 dated August 25, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
A201548 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-46 dated May 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A701548 2038029-
Supersedes Technical Service Bulletin Group 70 number 15-47 dated September 21, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A461523 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. New brake pads and/or discs have not been properly imbedded after installation. Aftermarket pads or discs are installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time. Discs are grooved. There is chemical contamination on the braking surface of the brake disc due to wheel or tire cleaner being sprayed directly onto the brake disc. There are ?pad marks? on the brake disc as a result of brake pad material transferring to the discs. Pad marks can occur when a vehicle has been parked for long periods of time in a wet or snowy environment.
A441557 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A511509 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing.
A911517 2042013-
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern.
A011544 2041944-
The MIL is on and/or glow plug light on. DTCs are stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Cars exhibiting the issue outlined in this TSB will also show a pattern in the DTC expanded ambient conditions under the P200200 fault code. Soot mass measured value above 40 g. Soot mass calculated value approximately 30 g. Kilometers since last regeneration value are above 500,000 m. The current ECM software does not accurately detect a momentary rise in DPF backpressure, resulting in a soot overload fault.
A871570 2041717-
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception.
A701547 2038029-
Supersedes Technical Service Bulletin Group 70 number 15-44 dated February 25, 2015. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A961501 2019260-
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
Email Mandatory
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
A171565 2038129-
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A191562 2025303-
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
2035173/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011542 2041787-
DTCs are stored in the ECM. There may be soot buildup on the moveable elements of the pressure sensing glow plug (PSG).
A9615002027416-6
Supersedes Technical Service Bulletin Group 96 number 14-85 dated July 24, 2014. The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
A911512 2036575-
Supersedes Technical Service Bulletin Group 91 number 15-80 dated March 20, 2015. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user?s myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations, accessing weather or other online information, or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. 2016 A6 and A7 vehicles have a known software issue that requires the myAudi PIN to be entered with each ignition cycle. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. Thi
ATE-15-19
To aid in diagnosing the high-voltage (HV) battery of the Audi Q5 Hybrid, Audi of America is pleased to inform you of the release and automatic delivery of the Audi Q5 Hybrid Minimum Required Tools (MRT) Shipment. Starting September 23, 2015, every Audi dealer will be shipped one AT-378 Audi Q5 Hybrid Special Tool Package, Freight F.O.B. Snap-On OEM and invoiced directly by the Audi Special Tools Program (Snap-On Business Solutions - SBS).
A911510 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-90 dated June 5, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up). No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
A871567 2041717-
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
A9415722032184-6
Supersedes Technical Service Bulletin Group 94 number 15-68 dated June 29, 2015. Customer may report that the daytime running light is completely inoperative, daytime running light is partially inoperative, and Multiple daytime running light LEDs are inoperative. DTCs are stored in the central electrics control module.
A921511 2040221-
Supersedes Technical Service Bulletin Group 97 number 15-46 dated April 2, 2015. The rear wiper is not functioning or only functions intermittently. Corrosion at the B536 splice of the rear wiper motor control circuit can cause an excessive voltage drop, resulting in an out of range control signal.
2041594/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201547 2041594-
The MIL is on. DTC P046100 (Fuel level sensor, circuit range/performance) is stored in the engine control module (ECM), J623 (address word 01).
A011538 2041566-
DTC P103200 (NOx sensor signal too high) is stored in the engine control module (ECM). Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts.
A211522 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-21 dated November 26, 2014. The MIL is on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall off due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
A9115082033313-3
Supersedes Technical Service Bulletin Group 91 number 14-46 dated June 25, 2014. Adaptive Cruise Control (ACC) does not work. The message "ACC no sensor vision" appears in the cluster. DTCs are logged in the distance regulation control module.
TSB-91-15-08
AUDI: SOME VEHICLES EXPERIENCE A DEACTIVATION OF ADAPTED CRUISE CONTROL (ACC) DUE RADAR SENSOR FAILING TO SEE OBJECTS FOR PERIOD OF TIME WHEN SNOW, LEAVES, WATER SPRAY BLOCKS RADAR SENSOR VISION. MODEL 2013-16 A4, A5, CABRIOLET, Q5. *PE
A481566 2034351-
Supersedes Technical Service Bulletin Group 48 number 15-65 dated March 23, 2015. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A0115362041120-2
Supersedes Technical Service Bulletin Group 01 number 15-26 dated June 30, 2015. The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). The diagnostic limitations were too narrow.
A0115322040962-2
Supersedes Technical Service Bulletin Group 01 number 15-25 dated June 19, 2015. The MIL is on. DTC P20E800 (Reductant pressure too low) is stored in the engine control module. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Hardware and software update is needed.
TSB-91-15-04
AUDI: SOME VEHICLES EXPERIENCE, INTERMITTENTLY, THE MMI DISPLAY FAILING TO DISPLAY REARVIEW CAMERA IMAGE DUE TO POSSIBLE WIRING HARNESS ISSUE. MODEL 2013-16 A4, A5, A8, Q3, Q5, Q7. *PE
A0115312033806-7
Supersedes Technical Service Bulletin Group 80 number 14-07 dated August 11, 2014. The MIL is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults may be stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss as a result of coolant migration in the electrical harness, faults in 08-Heating and Air Conditioning Electronics that result from coolant migration in the electrical harness, or a faulty N82 control valve.
TSB-01-15-31
AUDI: SOME VEHICLES WILL EXPERIENCE WARNING COOLANT LEVEL IS ON, ELEVATION OF ENGINE TEMPERATURE, AN ACTIVE LIMP HOME MODE DUE TO PERFORMANCE OF CLIMATE SYSTEM HEATING IS INSUFFICIENT DUE LOSS OF COOLANT RESULTING IN COOLANT MIGRATION OF ELECTRICAL HARNESS AND AIR CONDITIONING ELECTRONICS. MODEL 2010-14 A6, 7, 8, 4, 5, A5 CABRIOLET, TT, Q5, 7. *PE
A9615992038421-2
Supersedes Technical Service Bulletin Group 96 number 14-86 dated September 25, 2014. Customer reports that the side assist is providing warnings when no vehicles are present. The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning.
TSB-96-15-99
AUDI: SOME VEHICLES ARE EXPERIENCING A FALSE SIDE ASSIST WARNING WHEN RADAR REFLECTS FROM BACK OF REAR WHEELS TO SENSORS AND NO OTHER VEHICLES ARE PRESENT. MODEL 2009-17 Q5. *PE
A1915612025303-5
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A0115292041097-1
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
A301519 2019850-
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
SB-01-15-29
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
A011526 2041120-
The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow.
A011528 2040508-
Supersedes Technical Service Bulletin Group 01 number 15-21 dated April 29, 2015. The MIL is on. DTC P046100 (Fuel level sensor circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). DTC P046100 can be caused by miscalculations within the ECM software.
A461513 2040942-
Customer may complain about brake squeak or squeal with light to moderate pedal pressure.
A911598 2018187-
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A941568 2032184-
Supersedes Technical Service Bulletin Group 94 number 14-43 dated June 9, 2014. Customer may report that daytime running light is completely inoperative, daytime running light is partially inoperative, and multiple daytime running light LEDs are inoperative. DTCs are stored in the central electrics control module.
TSB-94-15-68
AUDI: SOME VEHICLES HAVE PARTIALLY INOPERATIVE DAYTIME RUNNING LIGHT OR NOT OPERATIVE COMPLETELY, OR HAVE MULTIPLE DAYTIME RUNNING LIGHT LEDS NOT OPERATIVE. MODEL 2013-15 Q5. *PE
A871564 2010146-
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
A961597 2034733-
Supersedes Technical Service Bulletin Group 96 number 13-71 dated July 22, 2013. The customer complains that after the vehicle is started, the name of the current radio station or media track is not shown in the driver information system (DIS). After the music input is changed to a different source and then changed back (i.e., media to radio to media or radio to media to radio), the radio station or media track information is shown in the DIS. Incorrect software.
A011525 2040962-
The MIL is on. DTC P20E800 is stored in the ECM. No relevant component or electrical problems are found when Guided Fault Finding (GFF) is run on the stored fault codes. Software update is needed.
A911594 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-28 dated March 6, 2014. MMI freezes or crashes and restarts when telephone address book is searched. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
A911595 2040926-
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
A971549 2040747-
The customer states that no gear is selected after the engine restarts from a start-stop phase. The car must then be shifted from D-->N-->D or from D-->P-->D for the first gear to be selected. The issue may be intermittent. The issue only occurs when the start-stop system is activated. There are no DTCs stored in the engine control module (ECM), J623 (address word 01) or the transmission control module (TCM), J217 (address word 02). If the issue does not match completely, do not proceed. This bulletin does not apply. Continue diagnosis with Guided Fault Finding (GFF). The voltage supply of the gearbox control unit is briefly interrupted due to the restart. This interruption causes the gearbox to change to N.
Executive Servic
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
A011524 2040491-
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
A911590 2040406-
Supersedes Technical Service Bulletin Group 91 number 15-87 dated May 18, 2015. When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). Q7 and Q3 vehicles are not affected by this condition. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A911589 2017425-
Supersedes Technical Service Bulletin Group 91 number 14-30 dated April 7, 2014. On generation III Concert and Symphony radios, the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence.
A171563 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A971548 2013504-
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
A911588 2026390-
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
A871563 2010146-
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A911587 2040406-
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle's actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. No DTCs related to the GPS antenna or MMI system are present. If the sky view is blocked because the vehicle is in a parking structure, below ground, or next to large buildings, it is normal for the GPS location or vehicle direction indicated on the MMI navigation map to not match the vehicle's actual location or direction of travel. The blocked sky view prevents the vehicle from receiving satellites, and the system may be temporarily lost until four satellites can be received. This is a normal condition, and is not related to the condition described above. Replacing the MMI main unit will not change this behavior. A potential failure in the internal hardware of the MMI main unit can cause the GPS signal to be blocked, even if good reception is available. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
A201546 2035073-
Supersedes Technical Service Bulletin Group 20 number 15-45 dated May 6, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911583 2030465-
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814. This bulletin only applies to vehicles with MMI3G+ Navigation (PR Number "7T6") and to vehicles with MMI3G+ Navigation, but without Audi Connect (PR Number "7T6" with additional PR code of "PND"). Continual improvements to MMI software provides solutions to issues experienced in the field.
A661553 2038652-
Supersedes Technical Service Bulletin Group 66 number 15-45 dated January 20, 2015. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A201545 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-43 dated December 19, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A921510 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
A661552 2035673-
Supersedes Technical Service Bulletin Group 66 number 15-50 dated April 10, 2015. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
A011521 2040508-
The MIL is on. DTC P046100 is stored in the ECM. DTC P046100 can be caused by miscalculations within the ECM software.
A391515 2028902-
Supersedes Technical Service Bulletin Group 39 number 14-14 dated May 5, 2014. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
A911582 2029903-
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
A461510 2040134-
Customer reports hearing a squeal noise from the front brakes during first brake application in the morning, with cold brakes, below 20 mph, below 40ºF, and high humidity.
A941565 2012749-
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
A941566 2017566-
Supersedes Technical Service Bulletin Group 94 number 13-12 dated March 29, 2013. The headlight switch knob was designed with a normal position and a pushed-in position. This feature was designed to avoid injuries during a collision.
A001575 2035505-
Supersedes Technical Service Bulletin Group 00 number 13-54 dated October 10, 2013. Audi of America (in conjunction with AUDI AG) is conducting a pilot program in the USA with a limited number of specially-built vehicles. These vehicles have a persistent internet connection and are designed to be accessed and started without the need for a traditional remote key. Instead, these vehicles use NFC (Near-field connectivity), or an iPhone with the Audi on Demand app, utilizing Bluetooth connectivity. The customer must leave the NFC card with the vehicle in order for the vehicle to be accessed and started.
A011519 2040403-
The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective.
A001574 2031122-
Supersedes Technical Service Bulletin Group 00 number 15-71 dated January 9, 2015. A repair authorization must be obtained if a Q5 hybrid arrives at an Audi dealership and requires diagnosis or repair for any of the following concerns. A Technical Assistance Center (TAC) ticket must be created before starting the repairs on the traction motor, power electronics, high voltage battery, high voltage cables, high voltage A/C compressor, auxiliary batter, and/or any hybrid warning messages in the instrument cluster. Prior authorization or a Technical Assistance Center (TAC) ticket is not required for repairs provided in any applicable TSB or RVU, for routine maintenance, for PDI, or for repairs on components and concerns not listed above.
A191558 2036852-
Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
A661550 2035673-
Supersedes Technical Service Bulletin Group 66 number 13-39 dated December 9, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
A971546 2040221-
The rear wiper is not functioning or only functions intermittently. Corrosion at the B538 splice of the rear wiper motor control circuit can cause an excessive voltage drop, resulting in an out of range control signal.
A961594 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-79 dated December 5, 2013. Audi side assist deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information panel. The system can be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Workshop finds that sporadic DTCs are stored in the lane change assistance control module, Audi side assist can be activated without issue, no obstructions found on the outside or inside of the bumper, no rework of the bumper can be found, the control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found on the inside or on the outside rear bumper area, and the control module mounting brackets are not broken or loose.
A661549 2030471-
Supersedes Technical Service Bulletin Group 66 number 15-46 dated February 19, 2015. Customer may report that the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate-length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
A481565 2034351-
Supersedes Technical Service Bulletin Group 48 number 14-57 dated January 29, 2014. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
A911579 2038824-
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A911580 2036575-
Supersedes Technical Service Bulletin Group 91 number 14-27 dated March 4, 2014. The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. This profile will be used each time the voice recognition system is used without a phone being paired to the MMI. This TSB is informational only and not applicable to any Audi warranty.
A101511 2018288-
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A191557 2040043-
Customer states that engine overheats. No MIL. No related DTCs are stored. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the overheat condition for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above. No changes to production have been made, as no issue has been identified.
A461506 2039615-
Supersedes Technical Service Bulletin Group 46 number 15-04 dated February 12, 2015. Customer may report hearing brake noise when the vehicle comes to a stop. Improved front brake pads introduced in production.
A171558 2038119-
Supersedes Technical Service Bulletin Group 17 number 14-52 dated September 2, 2014. The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
A911578 2011500-
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A011514 2014753-
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A171557 2010043-
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A701544 2038029-
Supersedes Technical Service Bulletin Group 70 number 14-39 dated August 11, 2014. Various squeaks and/or rattles are heard from the roof area on vehicles equipped with a panoramic sunroof. These noises can be created by the points of contact between the sunroof cover trim frame and the clips that retain it to the headliner.
A461505 2038056-
Supersedes Technical Service Bulletin Group 46 number 14-94 dated August 11, 2014. The brake pad wear indicator comes on, but brake pad thickness is above the wear limit.
A011507 2028344-
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
A461504 2039615-
Supersedes Technical Service Bulletin Group 46 number 15-03 dated February 9, 2015. Customer may report hearing brake noise when the vehicle comes to a stop from front brakes.
A941560 2017806-
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A461503 2039615-
Customer may report hearing brake noise when the vehicle comes to a stop from front brakes.
A461501 2039616-
The customer may report hearing a high-pitched squeal or squeak from the brake system during light brake application. May occur during colder weather or when backing out of a parking spot/garage in the morning. Improved front brake pads introduced in production
A701543 2039023-
Various squeaks and rattles are heard in the front or rear doors when the vehicle is driven over rough roads. Friction in the points of contact between the door trim panels can cause these noises.
A461500 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time
A661545 2038652-
Paint flakes off radiator grille or license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A901552 2039429-
The vehicle horn sounds abnormal or is inoperative. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. Contact the Audi Technical Assistance Center (TAC) before replacing any parts. No changes to production have been made, as no issue has been identified.
A011505 2036169-
The MIL is on due to a Fuel Rail/System Pressure Too Low DTC stored in the ECM. Drivability concerns such as hard starting/no starting are present. Fuel pump may be making a straining noise. Outside temperature is sub-freezing. This issue is related to the diesel fuel and not a technical problem with the vehicle.
A461599 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
A001571 2031122-
This document contains the Technical Service Bulletin that supersedes Technical Service Bulletin Group 00 number 13-50 dated May 22, 2013. A repair authorization must be obtained if a Q5 hybrid arrives at an Audi dealership and requires diagnosis or repair for the traction motor, power electronics, high voltage battery, high voltage cables, high voltage A/C compressor. Auxiliary battery, and any hybrid warning messages in the instrument cluster. A Technical Assistance Center ticket must be created before starting repairs. These procedures are mandatory until further notice.
9315012038152/2
2012-2015 AUDI Q5 HYBRID WARNING LIGHT LIGHTS UP IN THE INSTRUMENTAL CLUSTER, INDICATING THAT THE ELECTRIC DRIVE DOES NOT WORK. *CW
A931501 2038152-
?Hybrid drive: system error. Please go to workshop? is shown in the instrument cluster. Electric and hybrid operation are no longer possible. DTC P0AD600 is stored in the hybrid battery management module. The hybrid battery management control module unlearns the end stops of the air supply valve in the cooling module because of a software problem.
Edition117
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
20 14 43 2035073
EVAP System Leak Detected NVLD very small leak
20144320350737
System Leak Detected.
2035073/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201443 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-41 dated October 9, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A911472 2024323-
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
01140420353684
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011404 2035368-
Supersedes Technical Service Bulletin Group 01 number 14-84 dated July 28, 2014. MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
00147020392061
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
2036670/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A001470 2039206-
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
A941458 2036670-
Supersedes Technical Service Bulletin Group 94 number 14-34 dated March 7, 2014. The high beam is inoperative on one side of the vehicle. The low beams operate correctly. A warning may appear in the instrument cluster. DTCs may be present in the central electrics control module. The connection for the high beam shutter is not connected in the affected headlight.
441456202256311
Steering wheel shimmy, vibration, and/or oscillation
A441456 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
A901451 2021151-
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
Accessories Oper
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin.
Edition114
Wastegate linkage dissconnected
142120390062
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211421 2039006-
Supersedes Technical Service Bulletin Group 21 number 14-20 dated November 17, 2014. MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
EDITION 113
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition113
Technical bulletins and updates
145320390181
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
2039023/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A191453 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A701441 2039023-
Various squeaks and rattles are heard in the front or rear doors when the vehicle is driven over rough roads. Friction in the points of contact between the door trim panels can cause these noises.
142020390061
The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
2039006/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A211420 2039006-
MIL on. Customer may report a reduction in power. DTC P029900 (Turbo/Super Charger Underboost) is stored in the engine control module (ECM), J623 (address word 01). The circlip connecting the turbo wastegate actuator rod and the wastegate flap lever can fall of due to low tension of the clip. Consequently, the wastegate linkage becomes disconnected, causing MIL on and DTC P029900.
Edition112
Technical bulletins and updates
A851422 2033596-
Supersedes Technical Service Bulletin Group 85 number 14-20 dated February 24, 2014. DTCs may be stored in the heating and air conditioning electronics control module. A faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower can cause Improper operation of the fresh air blower.
A171453 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A911469 2038824-
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
Edition110
Technical bulletins and updates
00135720356692
When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
A571404 2027368-
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
Edition109
Audi Elsa Newsletter
44145520103346
Tightening wheel bolts
48146320282204
Steering wheel leather damage, all vehicles
A481463 2028220-
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
EDITION 108
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition108
Audi Elsa Newsletter
2038652/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A661443 2038652-
Supersedes Technical Service Bulletin Group 66 number 14-42 dated October 9, 2014. The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
A871458 2035582-
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
A911466 2020399-
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
A911467 2021037-
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
149820381661
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
87D9UPDATEa
AC Pressure/Temperature Sensor
87D9a
AC Pressure/Temperature Sensor (NVLW)
A011498 2038166-
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
Update Bulletin
This Update has been proactively released to prevent the following condition from occurring in the vehicle. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
87D9
AC Pressure/Temperature Sensor
A441455 2010334-
Supersedes Technical Service Bulletin Group 44 number 13-46 dated December 9, 2013. Wheel bolt requires torque adjustment.
144120350736
The NVLD pressure switch may erroneously detect a very small leak.
2035854/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2038652/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4014432035854
Rattling or knocking noise from front end when driving over bumps
A201441 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-34 dated June 26, 2014. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A401443 2035854-
Supersedes Technical Service Bulletin Group 40 number 14-42 dated July 8, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.
A661442 2038652-
The paint is flaking off of the radiator grille or front license plate holder. The surfaces of these components were too smooth (due to high-gloss polishing tools), which led to weak adhesion of the paint during production. Only components with color index T94 are affected.
Edition106
Audi Elsa Newsletter
37 14 48 2030007
TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.
37144820300075
Customer may report harsh shift concerns; no faults are stored and concern is reproducible
A371448 2030007-
Supersedes Technical Service Bulletin Group 37 number 12-65 dated September 25, 2012. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.
A911463 2028190-
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
Edition105
Audi Elsa Newsletter
2038421/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96148620384211
Lane change assist false vehicle warning (foil kit installation)
A961486 2038421-
Customer reports that the side assist is providing warnings when no vehicles are present. The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning.
A641436 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Edition104
Audi Elsa Newsletter
143820381132
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038113/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201438 2038113-
Supersedes Technical Service Bulletin Group 20 number 14-36 dated August 14, 2014. MIL on.DTC P310B is stored in the engine control module, J623 (address word 01), with symptom code 6183.
Edition103
Audi Elsa Newsletter
A921409 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
149120288422
Customer vehicle is fitted with unauthorized ECM tuning.
A011491 2028842-
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.
143720382761
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038276/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201437 2038276-
DTC P045600 is stored in the engine control module (ECM), J623 (address word 01). Note that this repair authorization applies only to a specific list of VINs. If this repair authorization does not appear in ELSA when your VIN is entered, it does not apply.
2035919/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911458 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-53 dated July 24, 2014. MMI 3G+ GPS location is inaccurate (MY13, MY14, & MY15).
145220381192
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
2038119/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A171452 2038119-
Supersedes Technical Service Bulletin Group 17 number 14-51 dated August 18, 2014. The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
Edition101
Audi Elsa Newsletter
24 14 50 2038212
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
A241450 2038212-
The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.
441454203027510
Repair Authorization
2038152/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
145120381191
The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
2038119/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
145020381291
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
143620381131
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the DTC code listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2038113/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-20-14-36
AUDI: DIAGNOSTIC TROUBLE CODE (DTC) P310-B00, LOW FUEL PRESSURE REGULATION OUTSIDE OF SPECIFICATION, SPORADIC/PASSIVE. SYMPTOM 6183. MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2014 A4, A5, A5 CABRIOLET, A6, A7, A8, Q5. *PE
44145320302759
Repair Authorization
2038056/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46149420380561
Brake pad wear warning - pads not at minimum
44145220302758
Repair Authorization.
A001467 2002047-
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC).
00146620379491
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
2024683/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A001466 2037949-
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
A911455 2024683-
Supersedes Technical Service Bulletin Group 91 number 13-87 dated June 19, 2013. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.
14-84
AUDI: REVISED WARRANTY ON TDI CLEAN DIESEL. *LJ
148420353683
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2036761/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011484 2035368-
Supersedes Technical Service Bulletin Group 01 number 14-81 dated June 24, 2014. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM). Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
A011485 2036761-
Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective.
Edition96
Technical bulletins and updates
Edition96-1
i-wire new wiring diagram application
2035919/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96148520274165
Sunglass holder will not close
A911453 2035919-
Supersedes Technical Service Bulletin Group 91 number 14-41 dated April 30, 2014. MMI 3G+ GPS location is inaccurate (MY14 & MY13).
A961485 2027416-
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
2037786/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2037786/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46149220377861
Squeal from front brakes (non-hybrid vehicles)_3.0T & 3.0TDI with PR-1LE
46149320377862
Squeal from front brakes (non-hybrid vehicles)_3.0T & 3.0TDI with PR-1LE
A461492 2037786-
Customer may report hearing brake noise when the vehicle comes to a stop.
A461493 2037786-
Supersedes Technical Service Bulletin Group 46 number 14-92 dated July 23, 2014. Customer may report hearing brake noise when the vehicle comes to a stop.
A461491 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A571402 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
001465201173210
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
2037770/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 14 22 2037770
Software improvement with more robust onboard diagnostics. If ECM software is current or newer than below, this bulletin cannot be applied. Follow GFF instructions.
A001465 2011732-
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
A261422 2037770-
The MIL is on. DTC P20FE00 (Reductant Metering Unit Performance) is stored in the engine control module (ECM). The ECM software version is older than the specified software for this bulletin. If ECM software is current or newer than below, this bulletin cannot be applied. Follow GFF instructions. Software improvement with more robust onboard diagnostics.
46148620225845
Brake pulsation diagnostic guidelines
A461486 2022584-
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
Edition94
Pending service solutions and bulletins
48146120360322
Steering feels stiff when turning
A481461 2036032-
Supersedes Technical Service Bulletin Group 48 number 13-56 dated December 13, 2013. The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.
A911450 2018187-
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
AUD4927ENG
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
TSB-48-14-61
AUDI: WHEN TURNING, THE STEERING FEELS STIFF AND OCCURS EVEN WHEN VEHICLE IS STATIONARY. INTERMEDIATE STEERING SHAFT NEEDS TO BE IMPROVED. MODEL 2008-2014 A4, A5, Q5. *PE
2035854/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4014422035854
Rattling or knocking noise from front end when driving over bumps
40144220358543
Rattling or knocking noise from front end when driving over bumps
A401442 2035854-
Supersedes Technical Service Bulletin Group 40 number 14-39 dated February 13, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.
EDITION 93
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition93
Technical bulletins and updates
4014402023187
Squeaking noises when steering or maneuvering
40144020231874
Squeaking noises when steering or maneuvering
4014412018194
Shock absorber leaks: assessment aid
40144120181946
Shock absorber leaks: assessment aid
A401440 2023187-
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A401441 2018194-
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
Edition92
Idenifying and mixing factory fill engine coolants
143420350735
The NVLD pressure switch may erroneously detect a very small leak.
20344445/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44145120344452
Message "TPMS" in instrument cluster
A201434 2035073-
Supersedes Technical Service Bulletin Group 20 number 14-32 dated March 21, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A441451 2034445-
Supersedes Technical Service Bulletin Group 44 number 13-38 dated July 11, 2013. Scenario A is after the engine is started, the message "TPMS" appears briefly then turns off. No DTCs are stored. Scenario B is the message "TPMS" appears constantly. DTC 03159 (tire pressure monitoring in ESP function) is stored in the ABS control module, J104 (address word 03), with one or more additional DTCs. Scenario C is the messages "TPMS" and "Tire pressure: System malfunction!" appear while the vehicle is being driven. DTC 03159 (tire pressure monitoring in ESP function) is stored in the ABS control module, J104 (address word 03), without other DTCs.
A911446 2033313-
Supersedes Technical Service Bulletin Group 96 number 13-54 dated March 15, 2013. Adaptive Cruise Control (ACC) does not work. Adaptive Cruise Control (ACC) does not work. The message "ACC no sensor vision" appears in the cluster. DTCs are logged in the distance regulation control module, J428 (13). Adaptive Cruise Control (ACC) is deactivated when the radar sensor does not see any objects for an extended period of time (varies based on environmental conditions). The most common cause for this type of deactivation is that the field of vision of the radar sensor is blocked.
148120353682
Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
2035368/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011481 2035368-
Supersedes Technical Service Bulletin Group 01 number 13-32 dated September 26, 2013. The MIL is on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01).Due to a production issue for the level sensor, the ECM cannot correctly read the reductant (AdBlue) fluid level.
EDITION 91
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition91
New structure changes to ElsaPro
A191450 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
SM702014
Pressure Switch
2032184/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941443 2032184-
Supersedes Technical Service Bulletin Group 94 number 14-38 dated April 7, 2014. Daytime running light is completely inoperative. Daytime running light is partially inoperative. Multiple daytime running light LEDs are inoperative. DTCs are stored in the central electrics control module, J519 (address word 09).
Edition89
ElsaPro Software update and technical bulletins
Service
Audi Tire Chain Information by Vehicle -- MY 2014
Service Informat
Audi Tire Chain Information by Vehicle -- MY 2014
2014 Audi Tire C
This document contians the Audi tire chain information for all MY 2014 vehicles.
2033379/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37 13 07 2033658
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A011479 2033379-
Supersedes Technical Service Bulletin Group 01 number 13-42 dated November 21, 2013. DTC P164D00 is stored in the engine control module. Red oil pressure warning light may be on. An oil filter that is too short is installed. The oil filter must be 155 (+/-1) mm long. If the oil filter is too short, the drain flap in the oil filter housing will not be completely closed and oil pressure will be reduced.
00146320335762
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
37 14 30 2003658
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37143020036586
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A001463 2033576-
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A371430 2003658-
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
23M6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
23M6UPDATE
ECM Software Update (FED_EMS)
Update23M6
ECM Software Update
SM-44-2014
AUDI: INFORMATION PROVIDED REGARDING MATERIALS BEING ORDERED OR REORDERED USING SAME PART NUMBER AND FILING A CLAIM FOR FUEL SENDER. *PE
SM442014
Fuel sender
441450202256310
Steering wheel shimmy, vibration, and/or oscillation
A441450 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.
Update91i8
Google Maps Street View (NVLW))
2037044/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46148320370442
Brake noise (non-hybrid vehicles)_3.0T & 3.0TDI with PR-1LE
A461483 2037044-
Supersedes Technical Service Bulletin Group 46 number 14-81 dated April 23, 2014. Customer may report that the front brakes squeal during the first stop in the morning when vehicle is back out of driveway and when brakes are applied after driving direction is changed at slow speeds (such as during parking lot maneuvers). This condition may occur more frequently during cold weather conditions (without rain), and the noise will disappear as temperature increases. This PSS TSB does not apply to Q5 2.0T and Hybrid models. Various parts have been replaced under warranty for the condition noted above, but no issues have been identified with the replaced parts.
2037029/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46148220370292
Squeal from front brakes (non-hybrid vehicles)_2.0T with PR-1LB
A461482 2037029-
Supersedes Technical Service Bulletin Group 46 number 14-80 dated April 23, 2014. Customer may report hearing brake noise when the vehicle comes to a stop.
2037166/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A721414 2037166-
The front lower seat frame has play or makes noise when the vehicle is cornering. The bolts on the seat pan that connect to the frame were not properly torqued by the supplier, and they can become loose.
39141420289023
Squealing, howling, or whistling noise from under vehicle when cold
A391414 2028902-
Supersedes Technical Service Bulletin Group 39 number 12-12 dated June 12, 2012. A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.
371422202898511
Transmission warning message in cluster (P074100 stored in TCM)
A371422 2028985-
Supersedes Technical Service Bulletin Group 37 number 13-01 dated April 24, 2013. Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
A911441 2035919-
Supersedes Technical Service Bulletin Group 91 number 13-17 dated December 3, 2013. The vehicle is a model year 2013 vehicle and TSB 2036607: 91 MMI3G+ Navigation GPS Location is inaccurate, has been completed. The GPS location or vehicle direction indicated on the navigation map does not match the vehicle's actual location or direction of travel.
27 14 24 2025360
Low battery charge: Diagnosis tips and TAC instructions
A271424 2025360-
Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.
Edition83
97 no start
2037029/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2037044/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
46148020370291
Squeal from front brakes
46148120370441
Brake noise (non-hybrid vehicles) 3.0T with PR-1LE
A461480 2037029-
Customer may report hearing brake noise when the vehicle comes to a stop.
A461481 2037044-
Customer may report that the front brakes squeal during the first stop in the morning when vehicle is back out of the driveway and when brakes are applied after driving direction is changed at slow speeds. This condition may occur more frequently during cold weather conditions (without rain), and the noise will disappear as temperature increases. This PSS TSB does not apply to Q5 2.0T and Hybrid models. Various parts have been replaced under warranty for the condition noted above, but no issues have been identified with the replaced parts.
143320368661
Some pumps may draw slightly too much current, which causes the fuel pump malfunction DTC to be stored.
2036866/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201433 2036866-
MIL and/or glow plug light on. DTC P304300 is stored in the engine control module. Some pumps may draw slightly too much current, which causes the fuel pump malfunction DTC to be stored.
A911438 2033780-
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface.
Edition82
91 Generation III radio: Loose or broken control knobs
44144920225639
Steering wheel shimmy, vibration, and/or oscillation
A441449 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
97144320367643
97 No start (DTC P068A00)
A971443 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition81
Elsa newsletter
A911436 2027903-
Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected.
A911437 2030947-
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
2026895/4
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2023006/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2032184/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911430 2017425-
Supersedes Technical Service Bulletin Group 91 number 10-08 dated March 18, 2010. On generation III Concert and Symphony radios , the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence.
A911431 2023006-
Supersedes Technical Service Bulletin Group 91 number 11-08 dated August 22, 2011. The parking aid system does not work. DTCs may be logged in parking aid control unit for disruption/short circuit to ground. The wire harness for the parking aid system may have been damaged when the front license plate frame was installed.
A941438 2032184-
Supersedes Technical Service Bulletin Group 94 number 13-21 dated July 9, 2013. Daytime running light is completely inoperative. Daytime running light is partially inoperative. Multiple daytime running light LEDs are inoperative. DTCs are stored in the central electrics control module.
TSB-91-14-31
AUDI: MULTIPLE DIAGNOSTIC TROUBLE CODES (DTC), ON SOME VEHICLES, IS CLOGGING THE PARKING AID CONTROL UNIT, CAUSING IT TO NOT WORK PROPERLY. MODEL 2009-2016 Q5. *PE
TSB-94-14-38
AUDI: VEHICLES ARE EXPERIENCING MULTIPLE FAILURE DAYTIME RUNNING LED LIGHT, DAYTIME RUNNING LIGHT COMPLETELY OR PARTIALLY FAILED. MODEL 2013-2015 Q5. *PE
144920284402
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
87D9UPDATE
AC Pressure/Temperature Sensor (NVLW)
A171449 2028440-
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Edition75
Technical bulletins and updates
Update87D9
AC Pressure/Temperature Sensor
920143
The Audi 2.0L Third Generation TDI Engine
144920368521
The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
97144220367642
97 No Styart (DTC P068A00)
A191449 2036852-
Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced.
A691428 2023323-
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.
A971442 2036764-
Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition79
Technical bulletins and updates
143220350734
The NVLD pressure switch may erroneously detect a very small leak.
A201432 2035073-
upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
147520366682
When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.
A011475 2036668-
Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.
A911429 2026888-
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
A971441 2036764-
The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.
Edition77
Technical bulletins and updates
147120367611
Updated oil pressure switch
97144120367641
97 No start (DTC P068A00)
A011471 2036761-
The MIL is on. DTC P164B(00) is stored in the ECM. The oil pressure switch is defective.
A801406 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-05 dated September 11, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module (address word 02). Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
9414582036670/2
AUDI : 2013-2016 Q5 : THE HIGH BEAM NOT WORKING ON ONE SIDE OF THE VEHICLE. LOW BEAMS WORKING PROPERLY, THE HIGH BEAM SHUTTER IS NOT CONNECTED IN THE HEADLIGHTS. *LJ
A941434 2036670-
The high beam is inoperative on one side of the vehicle. The low beams operate correctly. A warning may appear in the instrument cluster. DTCs may be present in the central electrics control module, J519 (address word 09). The connection for the high beam shutter is not connected in the affected headlight.
01146920366681
When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.
A011469 2036668-
The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.
A911428 2036576-
Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
96148220363441
96 Alarm sounds when driver door is unlocked with mechanical key
A911427 2036575-
The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered.
A961482 2036344-
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.
A871447 2010146-
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A851420 2033596-
Supersedes Technical Service Bulletin Group 85 number 13-17 dated May 15, 2013. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Improper operation of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower.
A911426 2036576-
The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when the user searches for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.
Edition74
Diagnostics and updates
00145920297372
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
A001459 2029737-
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
40143920358542
Rattling or knocking noise from front end when driving over bumps.
A401439 2035854-
Supersedes Technical Service Bulletin Group 40 number 13-37 dated December 3, 2013. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. High ambient temperatures at the hydraulic guide links cause the noise.
Edition72
Windows XP- End of Support (EOS) and new VAS diagnostic services
TSB-45-13-07
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. *PE UPDATED 05/21/2014 *JS
2035358/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4014382035358
Rattling/engine noises in passenger compartment
40143820353582
Rattling/engine noises in passenger compartment
A401438 2035358-
Supersedes Technical Service Bulletin Group 40 number 13-36 dated September 26, 2013. The customer complains that rattling or engine noise can be heard in the passenger compartment. The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing rattling or engine noise that can be heard in the passenger compartment.
Edition71
Technical bulletins and updates
01146320336302
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
2033630/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011463 2033630-
Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
TSB-01-14-63
AUDI: THE ENGINE WOULD HAVE A ROUGH IDLE, DIFFERENT MISFIRE FAULTS OR REDUCED PERFORMANCE WITHOUT LOSS OF POWER OR STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2008-2015 A3, A4, ALLROAD, TT, A5, A5 CABRIOLET, Q5, A6. *PE
01146220361693
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011462 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-59 dated January 21, 2014. The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
A911424 2020399-
Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.
A941432 2017806-
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.
01145920361692
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44144720302757
Alignment - Repair Authorization
A011459 2036169-
Supersedes Technical Service Bulletin Group 01 number 14-55 dated January 8, 2014. The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.
A441447 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. If the condition is due to outside influence (such as an accident), this TSB does not apply. In an effort to gain information on this condition, Audi of America is asking you to contact the Audi Technical Assistance Center (TAC) before you perform any repairs.
Edition69
Technical bulletins and updates
24AD
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
24ADUPDATEa
ECM Software Update (FED_EMS)
143120350733
The NVLD pressure switch may erroneously detect a very small leak. New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two components): part numbers 8K0906253 and 8K0906253B supersede to 8K0906253D. ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, which are integrated (one component): part numbers 8K0906253A and 8K0906253C supersede to 8K0906253E.
2035073/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A201431 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-28 dated November 14, 2013. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
A461466 2022584-
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
01145520361691
In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
2036169/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011455 2036169-
The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20° F (-7° C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.
A911419 2026895-
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
2014 MY Schedule
Maintenance.
MY 2014 Audi Nor
Tire Pressure Table.
REV11142013
Tire Pressure Table.
Edition67
Audi Elsa Newsletter
PDI-2014 ALL MOD
This document contains the Audi vehicle condition checklist. This document is in Spanish.
PDI-2014 Q5 DELI
This document contains the Audi delivery report checklist. This document is in Spanish.
PDI-2014 Q5 TECH
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. This document is in Spanish.
2036040/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A911318 2036040-
Customer complains that the parking aid sporadically warns of obstacles when none exist. Only vehicles with standard bumpers are affected. S-line (PR number 2K7 or 2K8) and S model (PR number 2K3 or 2K4) bumpers are not affected. A boundary layer between warm and cold air is recognized as an obstacle (e.g., hot exhaust gases in cold weather).
Edition66
Audi Elsa Newsletter
A481356 2036032-
The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.
TSB-48-13-56
AUDI: WHEN VEHICLE IS STATIONARY, THE STEERING WILL FEEL STILL WHEN TURNING AND THE STEERING SHAFT NEEDS TO BE UPDATED WITH IMPROVED INTERMEDIATE STEERING SHAFT. MODEL 2009-2014 A4, A5, A5 CAB, Q5. *PE
Reference-Audi M
This document contains the Audi normal load condition tire pressure table. This document is in Spanish.
2035173/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44134620103345
Tightening wheel bolts
A441346 2010334-
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
A571398 2035173-
Supersedes Technical Service Bulletin Group 57 number 13-96 dated October 16, 2013. Customer may report that the automatic door lock function cannot be deactivated. The "Lock when driving" (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door.
A661339 2035673-
Supersedes Technical Service Bulletin Group 66 number 13-38 dated November 15, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
TSB-44-13-46
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
2035047/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137920350473
Lane Change Assistant "Sensors Blocked" warning in DIS (DTC C1114F3 and C1115F5)
A961379 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-77 dated September 23, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes.The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. DTCs are stored in the Lane Change Assistance control module. Audi Lane Change Assistant can be activated without issue. No obstructions can be found on the outside or inside of bumper. No re-work of the bumper can be found. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found on the inside or on the outside rear bumper area. The control module mounting brackets are not broken or loose. In certain normal driving conditions, the Audi Side Assist system can automatically deactivate, and the driver information display shows the "sensors blocked" message. This is normal, as the nature of certain driving conditions can make it difficult for the Audi Side Assist system to track vehicles.
2027837/5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2035919/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4013372035854
Rattling/knocking noise from front end over bumps
40133720358541
Rattling/knocking noise from front end over bumps
A401337 2035854-
The customer reports hearing a rattling or knocking noise when the car is driven over bumps or uneven road surfaces. The noise is noticed after the car has been driven for a while and is warmed-up, and when the temperature outside is warm. The condition can be duplicated if the brakes are applied while the car is driven over bumps. High ambient temperatures at the hydraulic guide links cause the noise.
A641331 2027837-
Supersedes Technical Service Bulletin Group 64 number 13-26 dated June 7, 2013. The customer may report hearing noises when operating the window or noises from inside the door when driving on rough roads. When the window is lowered, it collides with the clip that holds the window guide cable. This causes the clip to open and contact the window during operation, or to rattle when the vehicle is driven on rough roads.
A911317 2035919-
GPS inaccuracies can be caused by several different factors. If it is unclear if this PSS applies, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket. Customer states the navigation system is not tracking the vehicle correctly. No DTCs related to the GPS antenna or MMI system are present. The issue occurs after the vehicle is parked overnight or for several hours in a parking garage or other similar enclosed space. A private home garage does not apply. The issue does not occur if the vehicle is parked overnight or for several hours in an open-sky environment. The condition continues for the duration of the drive. The issue only corrects itself with a 3-finger reset or during a vehicle sleep cycle. The vehicle is not a Q7 or A8. If the above conditions apply and the customer vehicle is a Q7 or A8, submit a Technical Assistance Center ticket for additional instruction. Perform Spec Actual and attach the GFF log to the ticket.
9013422035902 1
90 "Ignition lock faulty" message in cluster information display.
Audi Newsletter
Elso pro reminder.
Edition63
Audi Elsa Newsletter
4413442022563 8
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
44134420225638
Steering wheel shimmy, vibration and/or oscillation
A441344 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
2026757/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 13 20 2026757
An AdBlue message may appear in the instrument cluster either because there is a fault in the emission control system or because the system needs to be refilled. The AdBlue message displayed may vary depending on the model year of the vehicle.
6613382035673 2
Customer may report hearing wind noise from the front door area when the vehicle is driven at
A261320 2026757-
Supersedes Technical Service Bulletin Group 26 number 11-03 dated June 29, 2011. There is an AdBlue-related message displayed in the instrument cluster. MIL may or may not be illuminated.
A661338 2035673-
Supersedes Technical Service Bulletin Group 66 number 13-37 dated November 4, 2013. Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.
132820350732
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel tank cools off. If the natural vacuum leak detection (NVLD) system cannot detect this natural vacuum during the system self-test, the DTC will be stored in the ECM.
2013282035073 2
After the engine is switched off, the fuel system creates a natural vacuum as the fuel in the fuel ank cools off. If the natural vacuum leak detection (NVLD)
A201328 2035073-
Supersedes Technical Service Bulletin Group 20 number 13-27 dated October 16, 2013. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.
Normal Load Cond
This document contains the Audi normal load condition tire pressure table.
TableA
Tabla de presión de los neumáticos de condición de carga normal para Audi modelo 2014
2035797/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
5513332035797 1
The customer complains of hearing a creaking or knocking noise.
A551333 2035797-
The customer complains of hearing a creaking or knocking noise from the front of the vehicle when the vehicle is twisted, such as when being driven into or out of a driveway. The customer may describe the location of the noise source as the front suspension area. This type of noise may be caused by the contact between the hood height adjustment stop buffers and the lock carrier. While noises originating from the front of the vehicle may have a number of causes, the repair described below will eliminate this possible cause.
0013572035669 2
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7
A001357 2035669-
Supersedes Technical Service Bulletin Group 00 number 13-56 dated November 1, 2013. There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
AA001357-2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition61
Audi Elsa Newsletter
134720354632
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.
1713472035463 2
Electronic oil consumption measurement.
A171347 2035463-
Supersedes Technical Service Bulletin Group 17 number 13-44 dated October 22, 2013. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
2035710/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4613612035710 1
Customer may report hearing a clunk noise when brakes are applied at slow speeds.
9113142013790 8
The navigation DVD or other CD/DVD cannot be ejected.
A461361 2035710-
Customer may report hearing a clunk noise when brakes are applied at slow speeds after the vehicle has changed direction (e.g., parking lot maneuvers). This PSS TSB does not apply to Q5 Hybrid models. Various parts have been replaced under warranty for the condition noted above, but no issues have been identified with the replaced parts.
A911314 2013790-
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
Tire pressure Ta
2014 Audi Normal Load Condition Tire Pressure Table.
Edition60
Audi Elsa Newsletter
0013562035669 1
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7
00135620356691
When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
A001356 2035669-
There are special service instructions to be performed on all Model Year 2014 A6, A7, Q5, and Q7 vehicles before the vehicles are delivered to customers. When performing PDI inspections on vehicles delivered from November 2013 - February 2014, please prepare the vehicles for delivery with a special focus on the areas listed in this bulletin. These checks can be performed during the normal PDI inspection process.
AA001356-1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
QRSB-2014 Audi Q
This document contains the quick reference specification book.
2035626/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A681312 2035626-
Customer may report hearing a buzzing or rattling noise from the driver side dash and/or door area when the vehicle is driven over bumpy roads. An improper bolt torque sequence at the knee bar support bracket can cause unwanted vibration.
A571397 2022032-
Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
Reference-2014 N
This document contains the Audi normal load condition tire pressure table.
Reference-Oil Ca
This document contains the Audi oil capacity chart.
Table
Audi Normal Load Condition Tire Pressure Table
134420354631
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan.
A171344 2035463-
In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method.
10212013
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A691326 2023323-
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed.
A871346 2035582-
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Edition58
Audi Elsa Newsletter
Update24AD
ECM Software Update
PDIp
Informe del técnico de Audi
Edition57
Audi Elsa Newsletter
27 13 19 2029010
Low battery charge: excess current draw location
A271319 2029010-
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
2029586/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
27 13 18 2023282
Battery testing and charging - vehicles with BDM
A271318 2023282-
Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.
A661336 2029586-
Supersedes Technical Service Bulletin Group 66 number 13-34 dated September 30, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.
2026997/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A661335 2026997-
Supersedes Technical Service Bulletin Group 66 number 12-22 dated June 29, 2012. Customer may report hearing wind noise from the front door area. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise.
741312 2004327-4
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Chart
Audi Oil Capacity Chart
GuidelinesC
Audi Delivery Guidelines
PDI - 2014 All M
This document contains the Audi vehicle condition report checklist.
PDI - 2014 Q5-Q5
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
Report
Audi Technician Report
ReportF
Vehicle detail report
ReportG
Vehicle condition report
2029586/6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2033517/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A511307 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing.
A661333 2033517-
Supersedes Technical Service Bulletin Group 66 number 13-27 dated April 8, 2013. Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone.
A661334 2029586-
Supersedes Technical Service Bulletin Group 66 number 13-32 dated September 26, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.
48K8UPDATE
Power Steering Control Unit Software (NVLW)
A441342 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
01133220353681
Due to a production issue for the level sensor, the ECM cannot correctly read the Reductant (AdBlue) fluid level.
2035358/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2035368/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2035409/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
4013362035358
Rattling/engine noises in passenger compartment
40133620353581
Rattling/engine noises in passenger compartment
A011332 2035368-
MIL on. DTC P203B00 (Reductant Level Sensor Circuit Range/Performance) is stored in the engine control module (ECM), J623 (address word 01). Due to a production issue for the level sensor, the ECM cannot correctly read the Reductant (AdBlue) fluid level.
A661332 2029586-
Supersedes Technical Service Bulletin Group 66 number 13-31 dated June 12, 2013. The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.
A681311 2035409-
The customer may complain that a rattling noise can be heard coming from the driver?s side dashboard area when the driver is accelerating or driving over rough surfaces. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information on the concern for the vehicles listed above, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
2033412/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
45130720334122
ABS warning light on with additional warning lights on (EPB/TPMS/EPC/MIL) - Wire harness damage
A451307 2033412-
Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
A571394 2035367-
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
A721309 2035357-
Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
2035047/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137720350472
Lane Change Assistant "Sensors Blocked" warning in DIS (DTC C1114F3 and C1115F5)
A901341 2010353-
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
A961377 2035047-
Supersedes Technical Service Bulletin Group 96 number 13-72 dated August 26, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slowmoving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair.
A911308 2028190-
Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.
A401336 2035358-
The customer complains that rattling or engine noise can be heard in the passenger compartment. The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing rattling or engine noise that can be heard in the passenger compartment. Improved production process.
Edition53
Audi Elsa Newsletter
A481354 2028220-
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
01132820332243
If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.
2033224/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011328 2033224-
Supersedes Technical Service Bulletin Group 01 number 13-10 dated June 24, 2013. If a model year 2014 Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair. This also applies to any messages related to AdBlue shown in the DIS. These procedures are mandatory until further notice. Routine maintenance, PDI, and repair of other systems do not require prior authorization or a TAC ticket. Any repairs related to the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue or emissions) systems, or transmission completed without Repair Authorization via a Technical Assistance Center (TAC) contact will not be reimbursed. In an effort to gain information on the systems listed above, we are asking that you contact TAC before replacing any parts. This will assist us in diagnosing any potential issues.
A801305 2033806-
Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.
A911304 2013422-
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A871345 2024644-
Supersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.
A101310 2018288-
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A571393 2035173-
Customer may report that the automatic door lock function cannot be deactivated. The ?Lock when driving? (Autolock) configuration setting has been discontinued starting in some model year 2013 vehicles, and it is no longer available in the Car >> Vehicle Settings category in the MMI. The vehicle can still be unlocked while it is being driven, at any time, with the central locking switch in the door.
44134020277795
Steering rack control unit cannot be coded
A441340 2027779-
Supersedes Technical Service Bulletin Group 48 number 12-33 dated October 22, 2012. After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual. All new replacement power steering control units (J500) must be coded and parameterized using online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then the SVM code is required to code and parameterize the new replacement control unit. The SVM code can be found in Parts Bulletin 9-97, which is available online through ETKA.
AUDI Q5/SQ5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
ReferenceC
Quick Reference Specification Book
A911302 2018187-
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A961372 2035047-
Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slow-moving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair. The software of the Lane Change Assistance control module can deactivate the Audi Side Assist system in certain normal driving conditions because the nature of these driving conditions make it difficult for the Audi Side Assist system to track vehicles.
TSB-48-K-8
AUDI: UPDATED INFORMATION ON POWER STEERING CONTROL UNIT SOFTWARE, IN SOME VEHICLES, WITH ELECTROMECHANICAL POWER STEERING, HAVING SLIGHT IRREGULARITIES, MANUFACTURED A SPECIFIC PERIOD, MAINLY OCCURS WHEN TEMPERATURE IS AT FREEZING POINT. MODEL 2012-2014 A4, A5, Q5, A6, A7. *PE
A641329 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Dealer Letter-Up
This communication is to inform you of a revision to Update 24Z6. The revision is in regards to the manifold actuator.
A461354 2034988-
Customer may report that the front brakes squeal during the first stop in the morning while backing out of a driveway, applying the brakes after changing driving directions at slow speeds, and this condition may occur more frequently during cold weather conditions (without rain) and the noise will disappear as temperature increases. This PSS TSB does not apply to Q5 Hybrid models. Various parts have been replaced under warranty for the condition noted above, but no issues have been identified with the replaced parts.
A511306 2009967-
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing.
2013_06_ATU Audi
This document contains information on the Audi side assist update.
A571392 2022032-
Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).
Fluid Capacity C
This document contains the fluid capacity chart.
A911396 2026390-
Supersedes Technical Service Bulletin Group 91 number 12-38 dated March 2, 2012. When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.
Edition46
Audi Elsa Newsletter
2034733/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
96137120347331
Radio station or Media track information does not show in cluster DIS - Gen 3 Concert Radio
A961371 2034733-
The customer complains that after the vehicle is started, the name of the current radio station or media track is not shown in the driver information system (DIS). After the music input is changed to a different source and then changed back (i.e., media to radio to media or radio to media to radio), the radio station or media track information is shown in the DIS.
Edition45
Audi Elsa Newsletter
37 13 09 2028715
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
37130920287152
Rough gear changes both when accelerating and slowing down
A371309 2028715-
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
TSB-37-13-09
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE
TSB-94-13-21
AUDI: SOME VEHICLES ARE EXPERIENCING, PARTIAL OR COMPLETE, INOPERATIVE DAYTIME RUNNING LIGHT OR INOPERATIVE MULTIPLE DAYTIME RUNNING LED LIGHT. MODEL 2013-2014 Q5. *PE
A911392 2030947-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.
Edition44
Audi Elsa Newsletter
44133920302756
Alignment - Repair Authorization
A441339 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.
A441338 2034445-
Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. The "TPMS" message is not related to a loss of tire pressure. The message only indicates that tire pressure monitoring system (TPMS) is not active.
A961367 2019260-
Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
2033919/7
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011314 2033919-
MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective.
A941321 2032184-
Supersedes Technical Service Bulletin Group 94 number 13-05 dated February 8, 2013. Daytime Running Light is completely inoperative. Daytime Running Light is partially inoperative. Multiple Daytime Running Light LEDs are inoperative. DTCs are stored in the central electrics control module.
A461347 2034387-
Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.
Edition43
Audi Elsa Newsletter
PDI - 2014 Q5 Ch
This document contains the Audi delivery guidelines checklist.
A911388 2021780-
Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected.
Edition42
Audi Elsa Newsletter
GuidelinesA
Audi Delivery Guidelines
PDI - 2014 Q5
This document contains the Audi pre-delivery checklist.
AWA-13-05
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
01131020332242
If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.
2033224/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011310 2033224-
Supersedes Technical Service Bulletin Group 01 number 13-75 dated March 13, 2013. If a model year 2014 Audi Q5 TDI, A6 TDI, A7 TDI, or A8L TDI clean diesel (engine code CPNA or CPNB) requires diagnosis or repair of the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair. This also applies to any messages related to AdBlue shown in the DIS. These procedures are mandatory until further notice. Routine maintenance, PDI, and repair of other systems do not require prior authorization or a TAC ticket. Any repairs related to the engine, diesel fuel delivery, exhaust after-treatment (SCR/AdBlue or emissions) systems, or transmission completed without Repair Authorization via a Technical Assistance Center (TAC) contact will not be reimbursed. In an effort to gain information on the systems listed above, we are asking that you contact TAC before replacing any parts. This will assist us in diagnosing any potential issues.
01130920147538
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more conditions.
A011309 2014753-
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A191341 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A911387 2024683-
Supersedes Technical Service Bulletin Group 91 number 10-68 dated October 26, 2010. The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.
2029586/5
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
AWC-13-08
Audi is committed to enhancing the Initial Quality Experience for our Customers within the first days of vehicle ownership. We want to resolve any knowledge or technical concerns a customer may have about a new vehicle, and build a strong, positive, enduring relationship between dealer and customer. To support this commitment to both our dealers and our customers, Audi is introducing the Audi Second Delivery Program for MY2013 and MY2014 vehicles. The Program is applicable to all new MY2013 and MY2014 vehicles and includes a one-time reimbursement per VIN of $75. The Second Delivery may be performed at the dealership or a location of the customer?s choosing.
Edition39
Audi Elsa Newsletter
A661330 2030471-
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Edition38
Audi Elsa Newsletter
GuidelinesB
Audi Delivery Guidelines
2033675/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
00134920335761
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
2033884/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
26 13 16 2033884
If the battery management system detects an issue with the A1 auxiliary battery, EV Mode is disabled. When the ?EV Mode? button is pressed, the message ?EV mode is currently unavailable? (Figure 1) appears in the DIS, and EV mode does not activate.
A001349 2033576-
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Edition35
Elsaweb Newsletter
37 14 22 2028985
The fault occurs with ATF temperature below 60° C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.
2033675/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941316 2033675-
The customer may report that the tail lamp lighting does not switch between the rear lid and the bumper when the lid is operated. DTC 03703 (Rear lid -closed- sensor) may be stored in the comfort system central control module, J393 (address word 46).
28 13 21 2017555
Key does not stay or engage in ignition lock
A281321 2017555-
Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote keys are inoperable. The message "ignition lock faulty" may appear in the instrument cluster driver information display. DTC 00166 (Access/Start Authorization Switch -E415- Incorrect Signal) may be stored in Comfort System Central Control Module J393 (address word 46). It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position).
01138620336301
Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
A011386 2033630-
MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.
2033517/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A661327 2033517-
Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone.
A001348 2002047-
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
2036852/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941312 2017566-
Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.
133820129135
Engine oil service - filter cartridge replacement. When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.
A171338 2012913-
Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement.
A971335 2033412-
Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
A191335 2025303-
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A571386 2027368-
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
IQS
Audi On Track ? IQS Newsletter
A571385 2017082-
Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A571384 2024463-
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. High early warranty information related to inoperative remote keys necessitates this repair authorization. Through our combined efforts and cooperation, we will be able to raise the level of Audi quality and overall customer satisfaction.
4413362022563
Steering wheel shimmy, vibration and/or oscillation
44134220225637
Steering wheel shimmy, vibration and/or oscillation
A441336 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
A941306 2017806-
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.
SB-AOS-13-01
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A941305 2032184-
Daytime Running Light is completely inoperative. Daytime Running Light is partially inoperative. Multiple Daytime Running Light LEDs are inoperative. Error codes found in BCM1, address word 09: (DTC 02895 or DTC 02897), (Left or Right LED module daytime running lights and parking light, supply - Electrical fault in circuit, respectively).
SB-2032184/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A571382 2017082-
Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.
A911374 2024323-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
44133520225635
Steering wheel shimmy, vibration and/or oscillation
PDIm
Informe del técnico de Audi
PDIn
Informe del técnico de Audi
PDIo
Lineamientos de entrega de Audi
1335201004313
Engine oils that meet Audi Oil Quality Standards.
2032184/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
MaintenanceB
2014 Scheduled Maintenance Intervals
Scheduled Mainte
This document contains the scheduled maintence intervals.
A901238 2032113-
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
24ADUPDATE
ECM Software Update (FED_EMS)
0112562031368
Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC? s are present in the engine control module:
A011256 2031368-
MIL on. Engine misfire. Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.