TSB_2074436_3
Service Bulletin/Repair Instructions
This bulletin provides information when the horn sound quality is poor.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
TSB_2074436_3
This bulletin provides information when the horn sound quality is poor.
TSB_2068999_4
This TSB describes a corrosion issue due to outside influence and the prohibition of warranty in these cases.
TSB_2069078_4
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2069904_3
This bulletin provides information for all models regarding brake sounds.
TSB_2072304_4
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_20741717_15
This bulletin provides information on the GFF test plan required for AC compressor replacements regardless of the concern.
TSB_2075120_3
This bulletin provides information about the general approach for brake vibration concerns.
TSB_2079732_2
This bulletin provides information when there is a paint issue on alloy wheels.
TSB_2082846_1
This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.
TSB_2073282_1
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the dipped beam is switched on.
TSB_2082617_1
This bulletin provides information when there are noises in the overrun ( e.g. whirring, howling) - vehicles with 0BC.
TSB_2028902_5
This bulletin provides informaiton when the transmission warning message appears in the cluster; P074100 stored in the TCM.
TSB_2059335_7
This bulletin provides information when there are noises from the area around the instrument cluster.
TSB_2074729_3
This bulletin provides informationwhen noises/vibration are detected from front of vehicle in dynamic mode.
TSB_2082323_1
This bulletin provides informaiton when the engine is not running smoothly, misfiring.
TSB_2052680_6
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
AOS-26-25
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.
TSB_2074808_4
The high-voltage batteries in electric vehicles are subject to various ageing effects which could lead to the energy content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years
TSB_2022032_12
This bulletin provides diagnostic information for the vehicle locking system.
TSB_2070568_6
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2081531_1
This Reporting obligation requests that technicians contact the Technical Assistance Center (TAC) when the diagnostic tester refers to this reportin gobligation or to TPI 2033392.
TSB_2081409_1
This bulletin provides informaiton regarding the Universal Traffic Recorder.
TSB_2023187_8
This bulletin provides informaiotn regarding squeaking noises when steering or maneuvering.
TSB_2081405_1
This bulletin provides informaiotn about various infortainment system complaints.
TSB_2024323_13
This bulletin provides information when the parking assistance gives false warnings.
DC_Audi_CF_ Airbag
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent warning regarding counterfeit replacement airbag inflators that are being installed in used vehicles.
TSB_2024323_12
This bulletin provides information when the parking assistance gives false warnings.
TSB_2021205_10
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2059335_6
This TSB provides information when there are noises from the area around the instrument cluster.
TSB_2052680_4
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
TSB_2080329_1
This bulletin provides informaiotn when there are noises from the headliner.
TSB_2080681_1
This bulletin provides information regarding contact checks for event memories, intermittent.
TSB_2060750_5
This bulletin provides information regarding UV leak additive for finding oil leaks.
TSB_2074846_4
This bulletin provides information about vibrations and rotational steering vibrations.
TSB_2056019_5
This bulletin provides information when the anti-theft alarm activates for no reason, or does not activate.
TSB_2061669_3
This bulletin provides service infrmation for workshop mode with Audi connect vehicles.
TSB_2021205_9
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
TSB_2074808_3
This bulletin provides additoinal information to assist in determining the energy content of lithium-ion high-voltage batteries.
TSB_2018187_18
This bulletin provides information when there are speaker rattles, vibrations, or audio interference.
TSB_2069904_2
This bulletin provides information for all models regarding brake sounds.
TSB_2069078_3
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
TSB_2075120_2
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
TSB_2030471_8
This bulletin provides informaiton when the license plate mouting bracket threaded inserts are stripped.
TSB_2056386_11
This bulletin provides information about the steering wheel alignment.
TSB_2072304_3
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
TSB_2074846_3
This TSB provides information regarding rotational and other steerihng wheel vibrations.
TSB_2079732_1
This bulletin provides information when tehre is a paint issue on alloy wheels.
TSB_2047812_8
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator decomissioned).
TSB_2073917_2
This bulletin provides information for when there is a fluid sample request from Product Support.
TSB_2076605_2
This TSB provides informaiton pertaining to noises from the guide link bush.
TSB_2071264_2
This bulleitn provides information whent here are complaints about route guidance with Navigation.
TSB_2041717_14
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of the concern.
TSB_2042920_3
This bulletin provides information when there is corrosion on the tailpipes.
TSB_2070568_5
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2074436_2
This bulletin provides information when the horn sound quality is poor.
AOS-25-47
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
TSB_2060750_4
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
TSB_2027368_7
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
TSB_2010353_6
This TSB provides informatin when the cigarette lighter element does not eject, or the cigarette lighter is inoperable.
TSB_2070568_4
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
TSB_2042920_2
This bulletin provides information when there is corrosion on the exhaust tail pipes.
TSB_2056019_4
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
TSB_2077320_2
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2031473_6
This service information TSB describes a cosmetic issue after using a car wash.
TSB_2071893_2
This TSB provides damage assessment guidelines for textile seat covers.
TSB_2077320_1
This TSB is a label placement guide as required by CARB for remanufactured parts.
TSB_2028085_7
This bulletin provides information when there are leaks from the transmission.
TSB_2075530_2
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
TSB_2041717_13
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the concern.
TSB_2071185_2
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
TSB-2076945_1
This bulletin provides information about leather care and seat repair.
A6625162049680_3
This TSB provides information when the exterior rubber trim is spotted.
A4025932076605_1
This TSB provides informaiton pertaining to noises from the guide link bush.
A3725312074822_2
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
A5124322068999_3
This TSB provides information when there is cracked paintwork with corrosion at joint between roof and roof side member.
A8724952041717_12
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
A6624152046229_5
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
A2724842074729_2
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic mode.
A4424092056386_10
This bulletin provides information regarding wheel alignment.
A0124482014753_13
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system stored in the ECM P030000.
A3724292076084_1
This TSB provides information when event memory entries cannot be deleted (Mode$0A error) on gearboxes: DL501, DL382/DL382E and DQ500.
A9124872024323_11
This TSB Provides information when parking assistance provides false warnings.
A9124842018187_17
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
A0024992070568_3
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
A9324342074808_2
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A9624072056019_3
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does not activate.
A5724652022032_11
This bulletin provides diagnostic information regarding the locking system.
A1524532075530_1
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
CampTip_RNA_Audi
Vehicle Concerns Before Recall Repair Available
A2424632074810_2
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is working; mileage below 50 km/32 miles.
A8724892041717_11
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless of the concern.
A0024932002047_13
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical Assistnce Center (TAC).
A4424082074846_2
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
A5124312068999_2
This bulletin provides information when there is visible corrosion at the joint between the roof and roof side member.
A0024922031473_5
This bulletin provides informationw hen there are car was brush bristles trapped in the seam between the headlight and fender.
A4324982075100_1
This bulletin provides information on repairs on the air spring strut of the frong axle; additional sealing.
A4524462072304_2
This bulleitn provides information when there is an implausible signal in the ABS/ESC speed sensor.
A4524492075120_1
This bulletin provides information regarding the general approach to brakes rubbing.
A4624592069078_2
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic brakes.
A0124342074976_1
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in petrol.
A9124432074929_1
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
A9324042074808_1
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
A0024902074853_1
This bulletin provides service information ror when the fuel tank cannot be fully filled.
A3724222074826_1
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
A4424062074846_1
This bulletin provides information vibrations and rotational steering wheel vibrations.
A2424612074810_1
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not working; mileage below 50 km/32 miles.
A2724762074729_1
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
A3724132074750_1
This bulletin provides information about replacing the clutch end cover.
A3724142074751_1
This bulletin provides information about replacing the clutch end cover.
A3724212074822_1
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
A9124322018187_16
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
A8224002041717_10
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
A0024872002047_12
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center (TAC).
A9124252018187_15
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
A9424822074347_1
This bulletin provides informationw hen there are optical concerns with the tail lights.
DC_Q5 Hybrid
This document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday, June 24.
A9124162018187_14
This bulletin provides information when there are speaker rattles, vibration or audio interference.
A2124402044640_13
This bulletin provides information when the engine is difficult to start; turbocharger is damaged - 4.0L V8.
A5724432027368_5
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
A9424812073332_3
This bulletin provides information when there is noise while steering.
A5724422025031_3
This bulletin provides information when the exterior trunk handle is inoperative.
A1124002073917_1
This bulletin provides information for when there is a fluid sample request from Product Support.
A0024852021205_8
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
A872474202012414
This bulletin provides information when the air conditioning is no longer operative; DTC 00457, 00256, 01592.
A9024842032113_9
This bulletin provides general information regarding outside air temperature readings.
A9624962027416_7
This bulletin provides information when the sunglass holder will not close or is stuck closed.
A9024832059335_5
This bulletin provides information when there is noise from around the instrument cluster.
A9424762073332_2
This bulletin provides information for when there is noise when steering.
A2724712067906_5
This bulletin provides information for when DTC P0A7D00 is stored.
A5724342017082_1
This bulletin provides information when the remote control key is inoperative.
A9624952073471_1
This bulletin provides information when various driver assistance systems are unavailable - DTC C110702, B201200.
A9424742073332_1
This bulletin provides information if there is noise when steering the vehicle.
A9424722073282_1
This bulletin provides information on visual concerns with the headlight lens.
A872468204471710
This bulletin provides information when there is a faint noise heard in the cabin from the air conditioning circuit.
A9124632044694_3
This bulletin provides information pertaining to MMI Navigation database concerns.
A6824452038904_2
This bulletin provides information when the power outlet compartment is detached from the center console.
A0023822047812_7
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via the Mirror Server.
A912306202432310
This bulletin provides information when the parking assistance provides false warnings.
A4523362072304_1
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
A9023562032113_8
This bulletin provides general information about the outside air temperature reading.
A6623042030471_7
This bulletin provides information for when the license plate mounting bracket threaded inserts are stripped.
A0023812070568_2
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
A9423672071954_1
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
A7423262071893_1
This bulletin provides damage assessment guidelines for textile seat covers.
A0023762071721_1
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans (Ghost faults).
A0123812028842_4
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
A0023742052680_4
This bulletin provides information on the additional reporting requirements for safety related inquiries.
A0023732061669_2
This bulletin provides information on workshop mode with Audi connect vehicles.
A9123262071264_1
This bulletin provides information for when the customer has concerns about the navigation route guidance.
A6423922020552_1
This bulletin provides information for when exterior glass cleaning is needed.
A8723452041717_9
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
A9023322059335_4
This bulletin provides information for when there is noise from the area around the instrument cluster.
A922336203815115
This bulletin provides information for when the washer solvent level warning is on.
A4623452070679_1
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking switch; DTC C100C07 and/or C100C29.
A4823412028220_1
This bulletin provides information for instances where the steering wheel leather is damaged.
A102326201828810
This bulletin provides information on checking for debris when replacing an engine.
A9423652061922_3
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and taillights.
A5723082027406_5
This bulletin provides information regarding the Audi advanced key.
A922335203815114
This bulletin provides instructions for when the washer level warning is on but the reservoir is full.
A0023702021205_7
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
A0023692031473_4
This bulletin provides information for when car wash bristles become stuck in the body gap between the headlight and fender.
A912394201818713
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming, whining, or similar interference.
A9423632061922_2
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty submissions.
A4423992056386_9
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4423982056386_8
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4623432069904_1
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
A9023222032113_7
This information bulletin contains a background on the outside air temperature reading.
A192336202530314
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
A6423882047061_5
This bulletin describes the process to clean sticker residue from the windshield.
A4023512023187_7
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and repair is not needed.
A402352202431813
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9123832037809_1
This bulletin provides information on how to update the navigation map.
A9623822056019_2
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all. No DTCs are stored.
A462341203418123
This bulletin provides instructions for brake noise analysis and handling.
A012341201475312
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A9223332038151
This bulletin provides instructions for when the washer solvent level warning is on in the DIS but the washer solvent level is correct.
DC_Alternator_6
Support for Customers Affected by Alternator Back-order
A6423862047061_4
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an image of the suction cups used to install the windshield in production.
A6623942049680_2
This bulletin provides instructions for when the exterior trim has spots.
A4423972022563_2
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel while driving at highway speeds from 55 - 80 mph.
DC_Alternator_4
Support for Customers Affected by Alternator Back-order
DC_Alternator_5
Support for Customers Affected by Alternator Back-order
A8023122062583_2
This bulletin provides instructions for when the customer advises that there is insufficient or uneven cabin heating from the HVAC system.
DC_Alternator_3
Support for Customers Affected by Alternator Back-order
A9123592036576_7
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a symbol or emoticon is used in the name field for contact(s).
A4623402069078_1
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
A5123262068999_1
This bulletin provides instruction for when a customer advises that a visible line of corrosion is forming in the roof.
DC_Alternator_2
Support for Customers Affected by Alternator Back-order
DC_Alternator
Support for Customers Affected by Alternator Back-order
DC_RECALLS
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
A572200202203210
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A462234203418122
This technical service bulletin provides troubleshooting for brake noise.
A4822342065978_2
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering wheel isn't heating evenly.
A922230203815112
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A642285202055211
This bulletin provides instructions on how to properly clean exterior glass.
A4622332051095_7
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462232203418121
This technical service bulletin provides troubleshooting for brake noise.
A4522262067132_1
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted. See owner's manual" is displayed in the instrument cluster without DTCs.
A442292202256321
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A8722272041717_8
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A872225201014617
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation system.
A402238202431812
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
A9022572032113_6
This is an informational bulletin containing information about the outside temperature reading.
A9022582059335_3
This bulletin contains information on noises from the instrument cluster installation area.
A462230203418120
This technical service bulletin provides troubleshooting for brake noise.
A402237202431811
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
DC_20220329
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
A172219204064413
This bulletin provides repair instructions on diagnosing and replacing a leak in the crankcase breather module.
A1722172060750_3
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A2122392044640_1
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
A4622282051095_5
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A9122752024323_9
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A442287202256320
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A462226202258411
This informational bulletin provides diagnostic information for brake conditions.
A462227203418119
This technical service bulletin provides troubleshooting for brake noise.
A192228202530313
This bulletin contains instructions for identifying and mixing factory fill coolants.
A192227202530312
This bulletin contains instructions for identifying and mixing factory fill coolants.
A4421862056386_7
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4021302023187_6
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or maneuvered.
A4021312024318_1
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A212138204464011
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
A002155201173212
This bulletin contains general instructions for software updates.
A4421842065160_1
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
DC 20210928
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
A9121342018187_1
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A8721162041717_7
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
A0121102028842_3
This informational bulletin gives instructions for identifying chip tuning.
A2121372044640_1
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
A4821092028220_9
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by outside influence is not covered under warranty.
A4421832056386_6
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A1921222046712_3
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A2021352043357_1
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A0021482021205_6
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
A0021472031473_3
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent it from occurring again.
A9121042024323_8
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A0021442052680_3
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage).
A1021222018288_9
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
A9021032058077_5
This bulletin contains instructions for determining unexpected Audi presense interventions.
A1921172048936_3
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
A4421822056386_5
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A6421802020552_1
This bulletin provides instructions on how to clean exterior glass.
ELSAallignAudi
Elsa2Go campaign information is now 100% aligned with ElsaPro. This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
A9021002032113_5
This information bulletin contains a background on the outside air temperature reading.
A4021242016453_4
This bulletin contains instructions for determining if bushings need to be replaced.
A9021982059335_2
This bulletin contains information on noises from the instrument cluster installation area.
A6421792047061_3
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A5721752022032_9
This technical service bulletin provides troubleshooting information for the vehicle locking system.
A9121862062713_1
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
A8021112062583_1
This bulletin contains instructions for addressing an insufficient or uneven heating performance from the HVAC system.
A9421362023322_3
This informational bulletin contains information on the different shading of LED headlights.
A1321132062387_1
This bulletin contains instructions for determining if a repair is needed when coolant touches a poly V-belt and/or a toothed belt.
A9121762037809_8
This informational bulletin contains instructions about updating the navigation map.
A4621252054385_2
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill (crawling when pulling away or briefly before standstill).
A4421802056386_4
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A4621222051095_4
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
A462123202258410
This informational bulletin provides diagnostic information for brake conditions.
A462124203418118
This technical service bulletin provides troubleshooting for brake noise.
A4421792022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A6621692030471_6
This informational bulletin covers the condition of when license plate mounting bracket threaded inserts are stripped.
A9421332061922_1
This informational contains instruction on how to document optical concerns for warranty claims.
A1721122060750_2
This bulletin contains instructions for using the UV additive to find engine oil leaks.
A9121642024323_7
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A5520512014055_8
This bulletin contains instructions for addressing discoloration due to moisture on a new vehicle.
SM C-2020
This special notice is to inform dealers to return the part numbers listed (State of California only).
A5020042061716_1
This bulletin contains instructions for addressing a creaking noise in the floor.
A0020432061669_1
This informational bulletin contains instructions for Audi connect before performing any MMI work.
A2120362044640_9
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
A9120242026611_7
This bulletin contains a guide for troubleshooting HD radio issues.
A1720112060750_1
This bulletin contains instructions for using the UV additive to find engine oil leaks.
21AUTIRECHAINS
Added new graphic to reflect where to find MY 21 information
A9120112037809_7
This informational bulletin contains instructions about updating the navigation map.
A9020652032113_4
This information bulletin contains a background on the outside air temperature reading.
Audi Part Labels
Recall Reminder Part Labels
A1720062028440_5
This informational bulletin explains when the range display is empty in the on-board computer.
A6420752058551_3
This bulletin contains repair instructions for when the window switch is malfunctioning by opening instead of closing as directed by customer input.
A1920042025303_1
This bulletin contains instructions for identifying and mixing factory fill coolants.
A9020512058077_4
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A0020382039206_3
This informational bulletin contains instructions on how to use the QR code in a TSB.
A9120732026390_7
This bulletin contains instructions for correcting the phonebook.
A9120702044694_2
This technical service bulletin provides troubleshooting for issues with the navigation map database.
A4020052024318_9
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
A9120652036576_6
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
A6420742020552_9
This bulletin provides instructions on how to clean exterior glass.
A0020372059437_1
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing some issues.
A9020442032113_3
This information bulletin contains a background on the outside air temperature reading.
A9020452059335_1
This bulletin contains information on noises from the instrument cluster installation area.
A0020362002047_1
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
A6420722047061_2
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
A012054201475311
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A5120132009967_1
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
A012046201475310
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
A912039201818711
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
A1920012048936_2
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
A4420732056386_3
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
A9020372058077_3
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A9020362058077_2
This bulletin contains instructions for determining unexpected Audi pre sense interventions.
A921924203815111
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A0019292031473_2
This informational bulletin contains instructions for when car wash bristles are stuck in the headlights. 2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant
A9419182012749_1
Exterior lights, moisture accumulation 2013-2021 A3 Cabriolet, 2016-2018 Sportback, 2004-2005 A4 Cabriolet, 2004-2008 S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8
20AUTIRECHAINS
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
A9219232038151_1
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct. 2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant
A4419712022563_1
This bulletin provides information regarding vibrations or movement that are felt in the wheel. 2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7
145320381292
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A4019972018194_9
This bulletin contains repair instructions for leaking shock absorbers.
A0019262052680_2
This bulletin contains instructions for additional reporting requirements for safety related inquiries (airbag/seatbelts, accidents, fire and overheat damage.
ATUBody2019
Body components - Examples of customer misuse
A9119932037087_4
This bulletin contains instructions for enabling text message notifications through the MMI system.
A0019252011732_1
00 Software Version Management (SVM), operating instructions
A9119882024323_6
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A1719982028440_4
This informational bulletin explains when the range display is empty in the on-board computer. Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
A9619432056019_1
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off. Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
A2119322034999_4
This informational bulletin contains an explanation for a discolored pipe.
A201918204335711
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A201911 2043357
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
A011901 2046611
This bulletin provides repair instructions for when DTC P209600 and DTC P209800 appear and the reference duct is contaminated.
A921916 2038151
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A441969 2022563
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A171996 2048392
This bulletin contains software update information for when the instrument cluster display shows "Please reduce oil level."
A461903 2034181
This technical service bulletin provides troubleshooting for brake noise.
A001915 2047812
This informational bulletin contains instructions for setting up and using the SD creator program.
A011900 2046724
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries.
A011996 2046611
This bulletin provides repair instructions for when DTC P209600 and DTC P209800 appear and the reference duct is contaminated.
A011885 2046611-
This bulletin provides repair information for when DTC P209600 and DTC P209800 appear and the reference duct is contaminated.
ATU Powertrain
4.0T Camshaft diagnosis
A351833 2028085-
This bulletin contains instructions for diagnosing transmission leaks and repairing them.
Communication 19
Communication Toolkit for Dealers
A171894 2048392-
This bulletin contains software update ifnormation for when the instrument cluster display shows ?Please reduce oil level.?
A371882 2051685-
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor G676 are being replaced.
A011873
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries.
A011873 2046724-
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries.
A211829
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
A211829 2044640-
This bulletin contains repair instructions for when the engine cannot be started or it is difficult, there is unusual noises when accelerating and/or there is reduced engine performance.
ATU_Engine_Janua
4.0T Locating cause for coolant loss, known causes, corrections and TSB review
A011854 2046724_
This bulletin contains a software update to address occasional stalling or running erratically without a DTC. Occasional "System too rich" entries.
A011998 2046232
This bulletin provides a SVM code update for the ECM with up to three DTCs P011600, P017B00, and P011F00.
A011747 2048411
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment.
A011746 2038045
This technical service bulletin provides instructions for replacing the coolant thermostat with a new part number to resolve a stored DTC.
A211727 2044640
This bulletin contains detailed instructions and a worksheet for determining the damage on a turbocharger.
A011744 2049153
This bulletin contains continued instructions after completing 2041097.
A191791 2048936-
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
A511711 2009967-
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
Maint Flip Chart
Revision to Tires-rotate: 5K only; added "(except R8)"
A911743 2042097-
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI navigation.
SM 52-2017
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation 14s.
A941791 2012749-
This informational bulletin contains technical information for when there is condensation visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
A011728 2046232-
This bulletin provides a SVM code update for in Engine Control Module.
A911736 2024323-
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't exist or it is inoperative/constant warning.
A011726 2048411-
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment.
A011727 2048411-
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to 4,000rpm, and there are DTCs about the intake manifold flap adjustment.
A191789 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A171786 2048392-
This bulletin contains software update ifnormation for when the instrument cluster display shows ?Please reduce oil level.?
A401770 2018194-
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
21F2 - Circular
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
SM 44-2017 EN
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part numbers going forward.
A461772 2047830
This informational bulletin contains instructions for proper brake maintenance.
A011719 2046232-
This bulletin provides a SVM code update for in Engine Control Module.
21F2 - Bulletin
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
A011718 2038045-
This technical service bulletin provides instructions for replacing the coolant thermostat with a new part number to resolve a stored DTC.
21F2 - Dealer Le
On Audi vehicles with 4.0L TFSI engines manufactured within a specific period, the O-rings in the coolant lines for the turbocharger may be damaged. This can result in leaks between the coolant lines and the turbocharger.
A191788 2036167-
This bulletin provides instructions for a slow coolant leak from coolant connections.
A191787 2045456-
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
A441764 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A171782 2010043-
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil change.
A301722 2019850-
This technical service bulletin provides guidelines for diagnosing the clutch plate.
A011708 2041097-
This technical service bulletin provides instructions for troubleshooting and repairing the camshaft adjustment valve to correct a concern about the engine running irregularly.
A271729 2036392-
This technical bulletin provides software instructions for vehicle vibration between 1000 rpm and 3000 with two DTCs.
A191784 2045456-
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
A191782 2036167-
This bulletin provides instructions for a slow coolant leak from coolant connections.
Edition76
Technical bulletins and updates
ATE-17-05
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
A371775 2039267-
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle is brought to a stop or when a rattle noise is heard at idle speed.
A011702 2046611-
This bulletin provides repair information for when DTC P209600 and DTC P209800 appear and the reference duct is contaminated.
A191777 2046712-
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A211724 2044640-
This bulletin contains detailed instructions and a worksheet for determining the damage on a turbocharger.
A011799 2046611-
This bulletin provides repair information for when DTC P209600 and DTC P209800 appear and the reference duct is contaminated.
A011797 2046232-
This bulletin provides a SVM code update for in Engine Control Module.
A241658 2046232_
THIS BULLETIN PROVIDES A SVM CODE UPDATE FOR IN ENGINE CONTROL MODULE.
A191676 2036167_
THIS BULLETIN PROVIDES INSTRUCTIONS FOR A SLOW COOLANT LEAK FROM COOLANT CONNECTIONS.
A921614 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A871679 2041717-
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run a ODIS GFF test plan.
A271627 2036392-
This technical bulletin provides software instructions for vehicle vibration between 1000 rpm and 3000 with two DTCs.
A191675 2036167-
This bulletin provides instructions for a slow coolant leak from coolant connections.
A441662 2010334-
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
A441663 2022563-
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
A011682 2045598-
This bulletin provides repair information when a P023600 or P024000 appear in the tester.
A351623 2032211-
This technical service bulletin provides instructions for diagnosing an issue with the G676 sensor module and replacing it.
A921613 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A921612 2038151-
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A001684 2037949-
This technical bulletin provides instructions for an an error message and updating with an SVM code.
A191674 2036167-
This bulletin provides instructions for a slow coolant leak from coolant connections.
A1516292045455
THIS IS AN INFORMATION TSB REGARDING A CRACK THAT APPEARS TO BE A ON CYCLINDER HEAD.
A19167320454561
THIS IS AN INFORMATION BULLETIN REGARDING PROCEDURE FOR WHEN THE TECHNICIAN FINDS COOLANT MARKS DURING A REPAIR.
A21162320349993
THIS TECHNICAL SERVICE BULLETIN EXPLAINS WHY THE IMPELLER SIDE OF THE BANK 2 TURBOCHARGER LOOKS DISCOLORED.
A01167120410972
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AND REPAIRING THE CAMSHAFT ADJUSTMENT VALVE TO CORRECT A CONCERN ABOUT THE ENGINE RUNNING IRREGULARLY.
A20167420433582
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES.
2014
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2014 A6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2014 A6/S6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A241655 20446681
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR TROUBLESHOOTING AN ISSUE WITH THE OXYGEN SENSORS THAT CAUSES DTC P013E00 OR P014A00 TO BE STORED.
A6/S6
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A191671 2038045-
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR REPLACING THE COOLANT THERMOSTAT WITH A NEW PART NUMBER TO RESOLVE A STORED DTC.
A96160720295633
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A96160620295632
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
A35162220322114
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR DIAGNOSING AN ISSUE WITH THE G676 SENSOR MODULE AND REPLACING IT.
A57162520274063
THIS TECHNICAL SERVICE BULLETIN EXPLAINS THE DIFFERENCE BETWEEN KEYLESS GO AND AUDI ADVANCED KEY.
A91163920420133
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO DIAGNOSE AND RESOLVE ISSUES WITH AUDI CONNECT ONLINE DESTINATION SEARCH, GOOGLE EARTH NAVIGATION VIEW, AND INRIX ONLINE TRAFFIC.
A20166320433581
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC P046100 IN VEHICLES WITH V8 ENGINES.
A661546 2030471-
Supersedes Technical Service Bulletin Group 66 number 13-30 dated June 4, 2013. Customer may report that the license plate attachment screws do not install properly. License plate mounting bracket threaded inserts stripped.
A191666 2043142-
The MIL is sporadically on. One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
Elsa Newsletter
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition.
A351619 2032211-
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Scenario 1 is that entries are logged individually or in combination, with P179E logged first (using DTC environmental data).The entries are DTC P179E (Drive position sensor electrical error), DTC P0700 with DFCC 20196 (Transmission control system malfunction), DTC P1758 with DFCC 8464 (Terminal 15 voltage supply open circuit), and DTC P060A with DFCC 8126, 8345 (Internal control module monitoring processor performance) In this scenario, if DTC P179E is not logged first, this TSB does not apply. Scenario 2 is that entries are logged individually or in combination. The order in which the DTCs are logged is not relevant. The entries are DTC P179E with DFCC 8050, 8051, 8052, 8053, 17595, 17596, 17597, 17598, 17602 (Drive position sensor electrical error), DTC P179F with DFCC 8054, 8055, 8056, 8057, 17599, 17600, 17601 (Drive position sensor malfunction), DTC P0716 with DFCC 8096, 8101, 18153, 20738 (Input turbine/speed sensor ?A? circ. range/performance), DTC P171F with DFCC 8097, 8102, 18154 (Transmission input speed (RPM) sensor 2 implausible signal), DTC P0715 with DFCC 8094, 8103, 18161 (Input turbine/speed sensor ?A? circuit.), DTC P2765 with DFCC 8095, 8104 (Input turbine/speed sensor ?B? circuit), DTC P0501 with DFCC 8098 (Vehicle speed sensor ?A? range/performance), and DTC P2159 with DFCC 8099 (Vehicle speed sensor ?B? range/performance). Fault codes and DFCC codes must match exactly for this TSB to apply. The DFCC is the 4-6 digit code that is typically listed before the fault code. Incorrect driving mode sensor module.
A401549 2018194-
Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.
A911529 2013422-
Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A001578 2021205-
Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement.
A171568 2028440-
Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
A201559 2011703-
Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.
A911526 2042097-
The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.
Campaign Circula
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged. Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve.
A911524 2026611-
Supersedes Technical Service Bulletin Group 91 number 12-46 dated July 10, 2012. This Technical Bulletin provides an overview of HD Radio technology and terminology. The
A911528 2042013-
Supersedes Technical Service Bulletin Group 91 number 15-17 dated September 29, 2015. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. The following message appears in the MMI: ?This service is currently unavailable. Please try again later.? The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Additionally, if the vehicle is a model year 2016 A6, A7, or TT, the customer may not be able to see speed and flow traffic information in the navigation map screen, and may consistently see that no traffic reports are available. For these vehicles, traffic is provided by INRIX online.
Dealer Letter-Da
This document contain information on the upcoming emissions service action 17F9 in regards to the crankcase pressure regulating valve.
A511510 2009967-
Supersedes Technical Service Bulletin Group 51 number 15-09 dated October 2, 2015. Instructions for vehicle inspection, protection removal, and detailing.
A461525 2022584-
Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.
A171566 2040644-
Supersedes Technical Service Bulletin Group 17 number 15-64 dated June 3, 2015. A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTCs are stored in the ECM. A leak in the crankcase breather module (pressure regulating valve) can cause this condition.
A461523 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-02 dated February 9, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. New brake pads and/or discs have not been properly imbedded after installation. Aftermarket pads or discs are installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time. Discs are grooved. There is chemical contamination on the braking surface of the brake disc due to wheel or tire cleaner being sprayed directly onto the brake disc. There are ?pad marks? on the brake disc as a result of brake pad material transferring to the discs. Pad marks can occur when a vehicle has been parked for long periods of time in a wet or snowy environment.
A441557 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
A511509 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-07 dated September 30, 2013. Instructions for vehicle inspection, protection removal, and detailing.
Scheduled Maint
This document contains the scheduled maintenance intervals. The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Thereafter, all remaining scheduled services are due every 10,000 miles or 1 year after previous service, whichever occurs first.
A911517 2042013-
While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern.
A871570 2041717-
Supersedes Technical Service Bulletin Group 87 number 15-67 dated August 19, 2015. This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception.
A961501 2019260-
Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.
Email Mandatory
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
A351518 2028085-
Supersedes Technical Service Bulletin Group 35 number 13-12 dated June 18, 2013. Customer may report that there is oil leaking under the vehicle. Leaking from the oil pan seal. Crack in the oil pan. Leak between gearbox housing and intermediate housing. The source of the leak may be confused with o-ring of drain plug.
A171565 2038129-
Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A191562 2025303-
Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A871567 2041717-
Customer may report poor performance of A/C system or that the A/C system is inoperative. Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
A1915612025303-5
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A0115292041097-1
The MIL is on. Customer may report that the engine runs irregularly. DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
A301519 2019850-
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011. Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
SB-01-15-29
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
A911598 2018187-
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A871564 2010146-
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
A911595 2040926-
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
Executive Servic
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service.
A011524 2040491-
The MIL is on. "Coolant System: Fault Turn Off Engine" and the coolant symbol appears in the information panel. DTC P1B1C00 is stored in the ECM.
A171563 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A971548 2013504-
Supersedes Technical Service Bulletin Group 97 number 10-15 dated October 20, 2010. Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.
A911588 2026390-
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
A871563 2010146-
Supersedes Technical Service Bulletin Group 87 number 14-54 dated August 28, 2014. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
A011523 2036558-
Supersedes Technical Service Bulletin Group 01 number 14-99 dated October 16, 2014. The MIL is on. DTCs are stored in the ECM. ECM software adjustment of the secondary air pump motor (V101) runtime during the diagnosis phase.
A011522 2038045-
Supersedes Technical Service Bulletin Group 01 number 14-88 dated August 15, 2014. The MIL is on. DTC P218100 (Cooling System Performance) is stored in the engine control module (ECM), J623 (address word 01). DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map. Particles in the cooling system from the production process affect the closing of the coolant thermostat. Replacing the coolant temperature sender does not fix the problem.
A171562 2040644-
A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTC P2279 and DTC P0507 are stored in the ECM. A leak in the crankcase breather module (pressure regulating valve) can cause this condition.
A911583 2030465-
Supersedes Technical Service Bulletin Group 91 number 13-07 dated September 12, 2013. Group "A" complaints: Valid for vehicles with MMI software below version 566. Group "B" complaints: Valid for vehicles with MMI software at or above version 566 but below 715. Group "C" complaints: Valid for vehicles with MMI software at or above version 715 but not including 814. This bulletin only applies to vehicles with MMI3G+ Navigation (PR Number "7T6") and to vehicles with MMI3G+ Navigation, but without Audi Connect (PR Number "7T6" with additional PR code of "PND"). Continual improvements to MMI software provides solutions to issues experienced in the field.
A921510 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-09 dated September 12, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
A911582 2029903-
Supersedes Technical Service Bulletin Group 91 number 12-42 dated June 20, 2012. The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.
A941565 2012749-
Supersedes Technical Service Bulletin Group 94 number 12-92 dated October 24, 2012. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.
A271525 2036392-
Supersedes Technical Service Bulletin Group 27 number 14-23 dated April 24, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. Optimized J931 control module software.
A911579 2038824-
Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A101511 2018288-
Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A911578 2011500-
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A011514 2014753-
Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A171557 2010043-
Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A151526 2039995-
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day. The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner.
A011507 2028344-
Supersedes Technical Service Bulletin Group 01 number 13-69 dated February 14, 2013. Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.
A941560 2017806-
Supersedes Technical Service Bulletin Group 94 number 14-32 dated January 23, 2014. The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.
A461502 2034181-
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
A461500 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time
A461599 2034181-
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
Edition117
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
2039267/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
37145220392671
Bump after coming to a stop or rattle noise from transmission at idle speed
A371452 2039267-
Bump felt just after the vehicle is brought to a stop. Rattle noise heard from transmission at idle speed. The software of the transmission mechatronic control module, J743, needs to be updated.
A911472 2024323-
Supersedes Technical Service Bulletin Group 91 number 13-74 dated February 5, 2013. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
00147020392061
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet.
A001470 2039206-
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis. Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.
441456202256311
Steering wheel shimmy, vibration, and/or oscillation
A441456 2022563-
Supersedes Technical Service Bulletin Group 44 number 14-50 dated May 14, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.
A901451 2021151-
Supersedes Technical Service Bulletin Group 91 number 12-63 dated October 4, 2012. The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.
Accessories Oper
This is an advance notice for Audi of America employees. This notice contains information for the accessories operations technical bulletin.
145320390181
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3). The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A191453 2039018-
A small amount of dry or crusted coolant is seen on the coolant pump housing. The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
Edition112
Technical bulletins and updates
A171453 2038129-
Supersedes Technical Service Bulletin Group 17 number 14-50 dated August 15, 2014. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A911469 2038824-
The following message appears on the MMI display: ?Device or cable type not supported?. The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.
Edition110
Technical bulletins and updates
A571404 2027368-
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
44145520103346
Tightening wheel bolts
48146320282204
Steering wheel leather damage, all vehicles
A481463 2028220-
Supersedes Technical Service Bulletin Group 48 number 13-54 dated September 13, 2013. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
A871458 2035582-
Supersedes Technical Service Bulletin Group 87 number 13-46 dated October 21, 2013. The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
141920349992
The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe (Figure 1). This is a normal condition.
A211419 2034999-
Supersedes Technical Service Bulletin Group 21 number 13-17 dated August 16, 2013. On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger.
A911466 2020399-
Supersedes Technical Service Bulletin Group 91 number 14-24 dated January 24, 2014. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.
A911467 2021037-
Supersedes Technical Service Bulletin Group 91 number 13-85 dated May 29, 2013. The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.
149820381661
The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
87D9UPDATEa
AC Pressure/Temperature Sensor
87D9a
AC Pressure/Temperature Sensor (NVLW)
A011498 2038166-
The engine warning light is on after engine replacement. The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.
Update Bulletin
This Update has been proactively released to prevent the following condition from occurring in the vehicle. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
87D9
AC Pressure/Temperature Sensor
A441455 2010334-
Supersedes Technical Service Bulletin Group 44 number 13-46 dated December 9, 2013. Wheel bolt requires torque adjustment.
Edition106
Audi Elsa Newsletter
A911463 2028190-
Supersedes Technical Service Bulletin Group 91 number 13-08 dated September 20, 2013. The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.
35 14 17 2032211
Gearbox warning light
A351417 2032211-
Supersedes Technical Service Bulletin Group 35 number 12-08 dated December 21, 2012. The driver information system displays the message ?Gearbox malfunction: you can continue driving?. Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A).
A641436 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
Edition104
Audi Elsa Newsletter
A921409 2038151-
Supersedes Technical Service Bulletin Group 92 number 14-08 dated August 19, 2014. The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
149120288422
Customer vehicle is fitted with unauthorized ECM tuning.
A011491 2028842-
Customer vehicle is fitted with unauthorized ECM tuning. All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.
441454203027510
Repair Authorization
145020381291
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
148820380451
DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map. Particles in the cooling system from the production process affect the closing of the coolant thermostat.
2038045/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44145320302759
Repair Authorization
145120379941
In certain operating conditions, a function in the internal thermal management system can increase the engine temperature. Updated engine control module (ECM) software.
148620374722
DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
2037472/2
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2037994/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
44145220302758
Repair Authorization.
A001467 2002047-
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC).
00146620379491
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
A001466 2037949-
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
Edition96
Technical bulletins and updates
Edition96-1
i-wire new wiring diagram application
A461491 2034181-
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014. The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
001465201173210
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
A001465 2011732-
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
46148620225845
Brake pulsation diagnostic guidelines
A461486 2022584-
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
Edition94
Pending service solutions and bulletins
A911450 2018187-
Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
AUD4927ENG
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
4014402023187
Squeaking noises when steering or maneuvering
40144020231874
Squeaking noises when steering or maneuvering
4014412018194
Shock absorber leaks: assessment aid
40144120181946
Shock absorber leaks: assessment aid
A401440 2023187-
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
A401441 2018194-
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
EDITION 92
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Edition92
Idenifying and mixing factory fill engine coolants
148020374721
DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
2037472/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011480 2037472-
The MIL is on. DTC P310B00 (DFCC 2638) (Low fuel pressure regulation, fuel pressure outside specification) is stored in the engine control module, J623 (address word 01). DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
A191450 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
Edition89
ElsaPro Software update and technical bulletins
Service
Audi Tire Chain Information by Vehicle -- MY 2014
Service Informat
Audi Tire Chain Information by Vehicle -- MY 2014
2014 Audi Tire C
This document contians the Audi tire chain information for all MY 2014 vehicles.
37 13 07 2033658
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
00146320335762
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
37 14 30 2003658
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
37143020036586
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
A001463 2033576-
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A371430 2003658-
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
Update91i8
Google Maps Street View (NVLW))
EDITION 84
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2029714/3
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A641433 2029714-
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required.
27 14 23 2036392
Vibrations felt at 1000 rpm and 3000 rpm
27 14 22 2036392
Vibrations felt at 1000 rpm and 3000 rpm
A271422 2036392-
Supersedes Technical Service Bulletin Group 27 number 14-21 dated February 11, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules. As a result, the vehicle vibrates or judders when cylinders are actively switched off.
A911438 2033780-
Supersedes Technical Service Bulletin Group 91 number 13-83 dated May 2, 2013. Apple® devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface.
A271423 2036392-
Supersedes Technical Service Bulletin Group 27 number 14-22 dated April 21, 2014. Vibrations are felt at 1000 rpm and 3000 rpm. DTCs may be stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules. As a result, the vehicle vibrates or judders when cylinders are actively switched off.
A911437 2030947-
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
144920284402
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
87D9UPDATE
AC Pressure/Temperature Sensor (NVLW)
A171449 2028440-
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Edition75
Technical bulletins and updates
Dealer Letter -
This communication is to inform you of upcoming Update 87D9. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off.
Update87D9
AC Pressure/Temperature Sensor
920143
The Audi 2.0L Third Generation TDI Engine
Edition79
Technical bulletins and updates
A911429 2026888-
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
Edition77
Technical bulletins and updates
A871447 2010146-
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
00145920297372
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
A001459 2029737-
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
2036392/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
27 14 21 2036392
Vibrations felt at 1000 rpm and 3000 rpm
A271421 2036392-
Vibrations are felt at 1000 rpm and 3000 rpm. DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.
Edition70
Technical bulletins and updates
A941432 2017806-
Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.
44144720302757
Alignment - Repair Authorization
A441447 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013. Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. If the condition is due to outside influence (such as an accident), this TSB does not apply. In an effort to gain information on this condition, Audi of America is asking you to contact the Audi Technical Assistance Center (TAC) before you perform any repairs.
Edition69
Technical bulletins and updates
144820361941
The dashboard lights and controls may briefly flicker under hard acceleration after downshifting or when the engine is revved while the vehicle is stationary. The issue does not occur during normal driving, and all instrumentation continues to operate correctly. During periods of low electrical load (and especially when the battery is fully charged), the energy spike generated by the alternator due to the rapid increase in engine speed cannot be completely absorbed by the vehicle electrical system. This leads to a voltage increase that can cause some modules to initiate overvoltage protection. The condition is very brief and is considered normal.
A171448 2036194-
The dashboard lights and controls may briefly flicker under hard acceleration after downshifting or when the engine is revved while the vehicle is stationary. The issue does not occur during normal driving, and all instrumentation continues to operate correctly. During periods of low electrical load (and especially when the battery is fully charged), the energy spike generated by the alternator due to the rapid increase in engine speed cannot be completely absorbed by the vehicle electrical system. This leads to a voltage increase that can cause some modules to initiate overvoltage protection. The condition is very brief and is considered normal.
A461466 2022584-
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
A911419 2026895-
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
2014 MY Schedule
Maintenance.
MY 2014 Audi Nor
Tire Pressure Table.
REV11142013
Tire Pressure Table.
PDI-2014 A6 TECH
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection. This document is in Spanish.
PDI-2014 ALL MOD
This document contains the Audi vehicle condition checklist. This document is in Spanish.
Reference-Audi M
This document contains the Audi normal load condition tire pressure table. This document is in Spanish.
44134620103345
Tightening wheel bolts
A441346 2010334-
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
TSB-44-13-46
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
4413442022563 8
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
44134420225638
Steering wheel shimmy, vibration and/or oscillation
A441344 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
Audi Newsletter
Wind noise from Exterior Mirror.
Normal Load Cond
This document contains the Audi normal load condition tire pressure table.
TableA
Tabla de presión de los neumáticos de condición de carga normal para Audi modelo 2014
19J1
Update Bulletin
19J1-8J
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
19J1UPDATE
4.0 l Quality Package (NVLW)
Update Bulletin-
A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period. This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period.
2014 Audi Techni
Audi Technician report.
9113142013790 8
The navigation DVD or other CD/DVD cannot be ejected.
A911314 2013790-
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
PDI-2014 A6-S6-A
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
PDIg
Informe del técnico de Audi
ReportS
Audi Technician Report
Tire pressure Ta
2014 Audi Normal Load Condition Tire Pressure Table.
QRSB-2014 Audi A
This document contains the quick reference specification book.
19J1-C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
19J1UPDATEb
4.0 l Quality Package (NVLW)
19J1a
4.0 l Quality Package
Edition59
Audi Elsa Newsletter
19J1-B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
19J1UPDATEa
4.0 l Quality Package (NVLW)
19J1-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
19J18J
4.0 l Quality Package
Reference-2014 N
This document contains the Audi normal load condition tire pressure table.
Reference-Oil Ca
This document contains the Audi oil capacity chart.
Table
Audi Normal Load Condition Tire Pressure Table
A871346 2035582-
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Edition58
Audi Elsa Newsletter
PDIf
Lineamientos de entrega de Audi
01133620352351
fuel rail pressure too high; noises from engine compartment
2035235/1
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
A011336 2035235-
The customer reports that the engine warning light illuminates sporadically. The engine may have reduced performance without significant loss of power or stalling. Noise is heard coming from the engine compartment, specifically from the High Pressure Fuel Pumps 2. DTCs are stored in the engine control module (ECM). The fuel metering valve of the high-pressure fuel pump is controlled by a specific on/off ratio. If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. In such a situation, the fuel metering valve is deactivated and the high-pressure fuel pump switches to full supply mode. Because the increased rail pressure does not match the respective driving situation, the DTC appears.
TSB-01-13-36
AUDI: SOME VEHICLES ENGINE WARNING LIGHT SPORADICALLY ILLUMINATES, WOULD HAVE REDUCED PERFORMANCE WITHOUT LOSS OF POWER/STALLING OR NOISE COMING FROM ENGINE COMPARTMENT DUE TO LOW SYSTEM VOLTAGE, AND NOT ENOUGH ON/OFF RATIO TO KEEP FUEL METERING VALVE CONSTANT IN ALL AREAS, THE ENGINE CONTROL MODULE SOFTWARE NEED TO BE UPDATED. MODEL 2013-2014 S6, S7, A8, S8. *PE
27 13 19 2029010
Low battery charge: excess current draw location
A271319 2029010-
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
741312 2004327-4
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Chart
Audi Oil Capacity Chart
GuidelinesO
Audi delivery guidelines
PDI - 2014 A6-S6
This document contains the Audi technician report checklist. All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
PDI - 2014 All M
This document contains the Audi vehicle condition report checklist.
ReportC
Technician report
ReportF
Vehicle detail report
ReportG
Vehicle condition report
A511307 2009967-
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing.
Edition55
Audi Elsa Newsletter
A441342 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.
A571394 2035367-
Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.
A901341 2010353-
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
Edition53
Audi Elsa Newsletter
A481354 2028220-
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
A911304 2013422-
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
A101310 2018288-
Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
Audi
Quick reference specification book.
QRSB AUDI A6 S6
Quick reference specification book.
Quick Reference
Audi Quick Reference Specification Guide.
ReferenceB
Quick Reference Specification Book
A911302 2018187-
Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
A211317 2034999-
On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger. The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe. This is a normal condition.
A641329 2020552-
Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.
A511306 2009967-
Supersedes Technical Service Bulletin Group 00 number 11-23 dated June 3, 2011. Instructions for vehicle inspection, protection removal, and detailing.
Fluid Capacity C
This document contains the fluid capacity chart.
Edition46
Audi Elsa Newsletter
19J1b
4.0 l Quality Package
37 13 09 2028715
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
37130920287152
Rough gear changes both when accelerating and slowing down
A371309 2028715-
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
TSB-37-13-09
AUDI: IN SOME VEHICLES, THE CLUTCHES, AFTER HAVING TORQUE CONVERTER, COMPLETE GEARBOX REPLACEMENT OR MECHATRONICS, MUST ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE
A911392 2030947-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.
44133920302756
Alignment - Repair Authorization
A441339 2030275-
Supersedes Technical Service Bulletin Group 44 number 13-37 dated February 25, 2013. Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.
A461347 2034387-
Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.
GuidelinesM
Audi delivery guidelines
PDI - 2014 A6 Ch
This document contains the Audi delivery guidelines checklist.
Edition42
Audi Elsa Newsletter
PDI - 2014 A6 S6
This document contains the Audi pre-delivery checklist.
01130920147538
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more conditions.
A011309 2014753-
Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
A191341 2025303-
Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
AWC-13-08
Audi is committed to enhancing the Initial Quality Experience for our Customers within the first days of vehicle ownership. We want to resolve any knowledge or technical concerns a customer may have about a new vehicle, and build a strong, positive, enduring relationship between dealer and customer. To support this commitment to both our dealers and our customers, Audi is introducing the Audi Second Delivery Program for MY2013 and MY2014 vehicles. The Program is applicable to all new MY2013 and MY2014 vehicles and includes a one-time reimbursement per VIN of $75. The Second Delivery may be performed at the dealership or a location of the customer?s choosing.
A661330 2030471-
Supersedes Technical Service Bulletin Group 66 number 12-24 dated August 24, 2012. Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.
Edition38
Audi Elsa Newsletter
GuidelinesN
Audi delivery guidelines
00134920335761
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
A001349 2033576-
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
A001348 2002047-
Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
A191335 2025303-
Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
A571384 2024463-
Supersedes Technical Service Bulletin Group 57 number 12-72 dated September 24, 2012. Keyless entry is inoperative. Remote range is poor. Audi Advanced key is inoperative. High early warranty information related to inoperative remote keys necessitates this repair authorization. Through our combined efforts and cooperation, we will be able to raise the level of Audi quality and overall customer satisfaction.
4413362022563
Steering wheel shimmy, vibration and/or oscillation
44134220225637
Steering wheel shimmy, vibration and/or oscillation
A441336 2022563-
Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
0113692028344
Idle speed characteristic during cold start
A011369 2028344-
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.
A941306 2017806-
Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.
A911374 2024323-
Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
44133520225635
Steering wheel shimmy, vibration and/or oscillation
PDIm
Informe del técnico de Audi
PDIn
Informe del técnico de Audi
1335201004313
Engine oils that meet Audi Oil Quality Standards.
MaintenanceB
2014 Scheduled Maintenance Intervals
A6-S6
Audi Delivery Guidelines.
A6-S6-A
Audi Delivery Guidelines.
Scheduled Mainte
This document contains the scheduled maintence intervals.
A901238 2032113-
The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
0112572028344
Idle speed characteristic during cold start
A011257 2028344-
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.