2083061/1
Service Bulletin/Repair Instructions
Real Wear Setup and Guide using VYSOR
Vehicle report
2005 BENTLEY CONTINENTAL GT
Service bulletins
108 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
2051562/17
Service Bulletin/Repair Instructions
12 volt - Battery condition checks - Battery replacement requirements
2028794/10
Service Bulletin/Repair Instructions
Engine coolant mixture - Restrictions on use of desalinated water.
2051187/13
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: • Poor engine running • Reduced power • Engine warning lamp illuminated • Symptom related DTC’s evident within the applicable engine control unit(s)
2075786/3
Service Bulletin/Repair Instructions
Airbag, fire, accident (safety-related enquiry - reporting forms) There is a reporting obligation in the following cases: • Airbag/belt released/not released • General accident • Fire and scorching damage for all Bentley Vehicle models - every model year.
2071131/6
Service Bulletin/Repair Instructions
Measured values - Cycle recording instructions Condition: In some cases Measured value traces may be requested in XML format for analysis by Product Support Technical Background: The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis
2051562/16
Service Bulletin/Repair Instructions
12 volt - Battery condition checks - Battery replacement requirements. Customer statement / workshop findings: 12 volt battery flat or unserviceable
2051562/15
Service Bulletin/Repair Instructions
12 volt - Battery condition checks - Battery replacement requirements. Customer statement / workshop findings: 12 volt battery flat or unserviceable
2051562/14
Service Bulletin/Repair Instructions
12 volt - Battery condition checks - Battery replacement requirements. Condition: 12 volt battery flat or unserviceable
2071089/4
Service Bulletin/Repair Instructions
Electronic Parking Brake (EPB) control unit cannot be coded. Condition: The Electronic Parking Brake (EPB) control unit cannot be coded when using a diagnostic machine with Windows 10/11 in conjunction with a VAS 6154 dongle. As such the EPB coding application must be utilized to complete the procedure.
2061195/4
Service Bulletin/Repair Instructions
Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns.
2051187/12
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Condition: • Poor engine running • Reduced power • Engine warning lamp illuminated • Symptom related DTC’s evident within the applicable engine control unit(s)
2052785/10
Service Bulletin/Repair Instructions
Brake noise identification
2056407/7
Service Bulletin/Repair Instructions
Running gear - Noise identification. Condition Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system
2075786/2
Service Bulletin/Repair Instructions
Airbag, fire, accident (safety-related enquiry - reporting forms). There is a reporting obligation in the following cases: • Airbag/belt released/not released • General accident • Fire and scorching damage for all Bentley Vehicle models - every model year.
2028794/9
Service Bulletin/Repair Instructions
Engine coolant mixture - Restrictions on use of desalinated water. Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems
2064337/4
Service Bulletin/Repair Instructions
Usage of E10 fuel. Condition In the event a customer asks if E10 fuel can be used, the operative must refer to the Technical background section of this TPI.
2071131/5
Service Bulletin/Repair Instructions
Measured values - Cycle recording instructions. Condition: In some cases Measured value traces may be requested in XML format for analysis by Product Support.
2069806/7
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines
2069806/6
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines.
2075786/1
Service Bulletin/Repair Instructions
Airbag, fire, accident (safety-related enquiry - reporting forms). There is a reporting obligation in the following cases: • Airbag/belt released/not released • General accident • Fire and scorching damage for all Bentley Vehicle models - every model year.
2051187/11
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Condition: • Poor engine running • Reduced power • Engine warning lamp illuminated • Symptom related DTC’s evident within the applicable engine control unit(s)
2071131/3
Service Bulletin/Repair Instructions
Measured values - Cycle recording instructions. Condition: In some cases, Measured value traces may be requested in XML format for analysis by Product Support
2028794/8
Service Bulletin/Repair Instructions
Engine coolant mixture - Restrictions on use of desalinated water. Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems Demineralised water according to standard VDE 0510 meets all requirements and can be purchased worldwide Therefore undiluted coolant should be mixed in the correct ratio using demineralised water as detailed in Elsa Pro coolant specification, this will detail the ratio and type of coolant to use The use of desalinated water in the engine cooling system is specifically prohibited
2064337/3
Service Bulletin/Repair Instructions
Usage of E10 fuel. Condition: In the event a customer asks if E10 fuel can be used, the operative must refer to the Technical background section of this TPI Technical Background: Details on the introduction of E10 fuel which contains 10% ethanol and its usage on Bentley products • All vehicles produced post 1990 Model year can be run using E10 fuel However • All vehicles produced before 1990 Model year MUST NOT use E10 fuel
2056407/6
Service Bulletin/Repair Instructions
Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering.
2052785/9
Service Bulletin/Repair Instructions
Brake noise identification. Technical Background: Brake noises can be attributed to many causes, the most common causes are as follows: • Brake discs or pads are close to their wear limit • New brake pads and/or discs have not been properly bedded in after installation • Aftermarket pads or discs are installed • There is debris such as small stones, grit, road salt or sand between the brake disc and pad • Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time
2071131/2
Service Bulletin/Repair Instructions
Measured values - Cycle recording instructions. Technical background The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis.
2071089/3
Service Bulletin/Repair Instructions
Electronic Parking Brake (EPB) control unit cannot be coded. Customer statement / workshop findings The Electronic Parking Brake (EPB) control unit cannot be coded when using a diagnostic machine with Windows 10 in conjunction with a VAS 6154 dongle.
2069806/5
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
2051562/12
Service Bulletin/Repair Instructions
12 Volt - Battery condition checks. Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section.
2072055/1
Service Bulletin/Repair Instructions
Spurious DTC identification. Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.
2028794.7
Service Bulletin/Repair Instructions
Engine Coolant Mixture - Restrictions on use of desalinated water Customer Statement: -Engine coolant requires topping up or replacing
2052785.8
Service Bulletin/Repair Instructions
Brake Noise Identification: Customer Statement: -Noise/squeal complaint from the braking system Technical Background: -The noise/squeal can be reproduced and clearly assigned to the braking system
2061195/3
Service Bulletin/Repair Instructions
Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.
2056407.5
Service Bulletin/Repair Instructions
Running gear - Noise identification Workshop Findings: -The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work
2051562/11
Service Bulletin/Repair Instructions
12 Volt - Battery condition checks. Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section
2053177/19
Service Bulletin/Repair Instructions
All Vehicle Variants - Spurious DTC List. Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).
2069806/4
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
2069806/3
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.
2069806/2
Service Bulletin/Repair Instructions
HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.
2071089/1
Service Bulletin/Repair Instructions
Electronic Parking Brake (EPB) control unit cannot be coded. Customer statement / workshop findings: The Electronic Parking Brake (EPB) control unit cannot be coded when using a diagnostic machine with Windows 10 in conjunction with a VAS 6154 dongle. Technical background: Should Windows 7 and/or VAS 5054 no longer be available the retailer must conduct the following: - Raise a technical DISS query stating the EPB control unit cannot be coded as access to a diagnostic machine with Windows 7 and a VAS 5054 dongle is no longer possible - Await a response via DISS regarding all applicable next steps. Do Not raise a DISS if the operative has access to a diagnostic tester with Windows 7 and a VAS 5054 dongle as the EPB control unit can be coded by the operative without raising a DISS query.
2051187/9
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: - Poor engine running - Reduced power - Engine warning lamp illuminated - Symptom related DTCs evident within the applicable engine control unit(s) Technical background: Technical Product Information (TPI) to assist retailers when diagnosing poor engine running or misfires.
2069806.1
Service Bulletin/Repair Instructions
HVAC Refrigerent Leakage - Diagnosis Guidelines Customer Statement: -HVAC not cooling or HVAC cooling less than expected
2036678.5
Service Bulletin/Repair Instructions
Speaker Replacement - Diagnostic Checks Technical Background: -There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.
2051187.8
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only Customer Statement: -Poor engine running, reduced power, engine warning lamp illuminated.
2051562.10
Service Bulletin/Repair Instructions
12 Volt - Battery Test Instruction Technical Background: -For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI.
2061195.2
Service Bulletin/Repair Instructions
Telephone Functionality Complaint- Minimum Standards Required For Analysis of Concerns Customer Statement: -The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.
2056407.4
Service Bulletin/Repair Instructions
Running Gear - Noise Identification Customer Statement: -Noise complaint from the suspension and/or steering
2064337.2
Service Bulletin/Repair Instructions
Usage of E10 Fuel Customer Statement: -In the event a customer asks if E10 fuel can be used, the operative must refer to the Technical background section of this TPI
2051187.7
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only Customer Statement: -Poor engine running, reduced power, engine warning lamp illuminated.
2051562.9
Service Bulletin/Repair Instructions
12 Volt- Battery Condition Checks. Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.
2053492/8
Service Bulletin/Repair Instructions
Air spring fault finding Customer Statement: -The front and/or rear suspension appears to have dropped Technical Background: -Bentley vehicles which are applicable to this TPI are fitted with air springs as part of the suspension system. Should air leak from the air spring dampers, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. -The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air supply unit, pipes, valve unit and air reservoirs. This includes potential air leak points on the air spring dampers and also the locations of an air leak that can be repaired without the need to replace an air spring damper.
2051562/8
Service Bulletin/Repair Instructions
12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI
2056582/4
Service Bulletin/Repair Instructions
Interior trim - Creak and rattle - Noise identification Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work
2033864/6
Service Bulletin/Repair Instructions
Customer statement / workshop findings: Unable to remove Accessory valve caps, Figure 1 shows an example of the caps. Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident
2036678/4
Service Bulletin/Repair Instructions
Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference
2051187/6
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.
2051562/7
Service Bulletin/Repair Instructions
12 Volt - Battery condition checks. Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI
2052785/6
Service Bulletin/Repair Instructions
Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
2056407/3
Service Bulletin/Repair Instructions
Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system
2063025/1
Service Bulletin/Repair Instructions
Powered Boot fails to operate due to faulty motors - Replacement motors unavailable to obtain Customer statement / workshop findings: Powered boot fails to operate due to faulty motors, replacement motors are unavailable to obtain Technical background: Refer to the Measure section of this TPI to allow the boot to be used in manual mode
2051562/6
Service Bulletin/Repair Instructions
All Models - 12 Volt Battery condition checks. Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.
2061195/1
Service Bulletin/Repair Instructions
Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.
2058173/2
Service Bulletin/Repair Instructions
Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
2052785/5
Service Bulletin/Repair Instructions
Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).
2056582/3
Service Bulletin/Repair Instructions
Interior trim - Creak and rattle - Noise identification. Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work
2053492/6
Service Bulletin/Repair Instructions
Air spring fault finding. Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. TheMeasure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. These checks should be carried out in conjunction with the Elsapro procedure Air suspension: To check with the use of the special tool Air suspension leak tester VAS 751 001 shown in the image below as item ( 1). Refer to Elsapro, Repair Group 43, Air suspension To check.
2058173/1
Service Bulletin/Repair Instructions
Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI
2051187/5
Service Bulletin/Repair Instructions
Condition: Poor engine running, reduced power, engine warning lamp illuminated. Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.
2051562/5
Service Bulletin/Repair Instructions
Condition: 12 Volt Battery test instruction Technical Background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI
2052785/4
Service Bulletin/Repair Instructions
Condition: Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4).
2053492/5
Service Bulletin/Repair Instructions
Condition: The front and/or rear suspension appears to have dropped. Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues.
2056407/2
Service Bulletin/Repair Instructions
Condition: Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI
2056582/2
Service Bulletin/Repair Instructions
Condition: Customer statement: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI
2056392/1
Service Bulletin/Repair Instructions
Customer statement / workshop findings: When selecting to update the date (Figure 1) and time (Figure 2) by GPS, the two features will no longer automatically update via GPS. Technical background: A reset to the GPS network has meant the automatic GPS date and time feature no longer functions.
2033864-5
Service Bulletin/Repair Instructions
Accessory valve caps - Difficult to remove
2051187.3
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only
2051562.4
Service Bulletin/Repair Instructions
12 Volt - Battery condition checks
2052785.3
Service Bulletin/Repair Instructions
Brake noise identification
2051187.1
Service Bulletin/Repair Instructions
Poor Engine Running Complaints (Misfires) Petrol Engines Only
20274332
Service Bulletin/Repair Instructions
Clicking noise from wheel bearing
2043974/2
Service Bulletin/Repair Instructions
REPLACING FRONT WISHBONE LINKS *REVISED*
SB-2036869-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033745-2A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2034004-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2030217-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
2034004/1
Service Bulletin/Repair Instructions
Continental GT - Continental Flying Spur - Replacement engine identification Customer statement / workshop findings: Should an engine be required for a Continental GT or Continental Flying Spur and the model year of the vehicle is 2004 to 2006, Bentley Motors supplies replacement engines which have been specifically manufactured as a direct replacement for the original specification engine. The replacement engine is based on a 2012 model year engine. IMPORTANT: This TPI only applies to 2004 to 2006 Continental GT and Continental Flying Spur vehicles fitted with a 2012 M/Y replacement engine, No other model years or engine types are affected. Other replacement parts unless mentioned within this TPI are not affected Technical background: The Measure section highlights the following key points: Section 1 - How to identify if a replacement engine is fitted Section 2 Details the parts which are different from the original specification 2004 to 2006 model year engine Section 3 How to manually populate and navigate to the applicable screen in Elsa Pro and ETKA without using the actual VIN, this ensures the correct parts are received for a 2012 engine
2036869/1
Service Bulletin/Repair Instructions
Continental GT - Continental Flying Spur - Replacement engine identification (SC14/19) Technical background: The engine fitted to this vehicle is a service replacement engine, in order to allow the engine to be identified as a service replacement engine for future parts and workshop manual information the instructions within this procedure must be followed. The service replacement engine is based on a 2012 model year W12 engine. Remedy: This campaign must be carried out on all applicable vehicles within the specific VIN range to ensure all affected vehicles are checked and repaired as detailed within the onward instructions.
SB-20362667-1
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2028318-3
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2030217-2
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033864-2A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033864-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033717-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033742-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2033745-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2032874-1A
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-2028318-2
Service Bulletin/Repair Instructions
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TB-10-01-01-02
Service Bulletin/Repair Instructions
BENTLEY: A CONDITION HAS BEEN IDENTIFIED THAT CAN COMPROMISE THE SURFACE FINISH OF THE PIPE SUPPLYING LUBRICANT TO THE TURBOCHARGERS. IF LEFT UNDETECTED THE PIPE MAY CORRODE AND, IN EXTREME CASES, RESULT IN FLUID LOSS. NO MODEL YEARS LISTED. *PE
BB-09-128
Service Bulletin/Repair Instructions
BENTLEY SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. CONTINENTAL SERIES (INCLUDING GT DIAMOND SERIES): EMISSIONS SERVICE ACTION, IGNITION COILS. THE VEHICLES AFFECTED MAY HAVE IGNITION COILS THAT COULD MALFUNCTION UNDER CERTAIN CONDITIONS. IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATE TO INFORM THE DRIVER THAT THE VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. CSC LETTER WAS REC'D. *PE
TB-09-01-00-12
Service Bulletin/Repair Instructions
BENTLEY: ON UK AND US REGION CARS ONLY, THE GUIDED SERVICE FUNCTION REPLACE-C00202 DRIVER INSTRUMENT PANEL [J285] INCORRECTLY ASKS FOR THE TOTAL DISTANCE TRAVELED AND DISTANCE TRAVELED SINCE LAST SERVICE TO BE ENTERED IN KILOMETERS. THIS MESSAGE IS INCORRECT AND THESE DISTANCES NEED TO BE ENTERED IN MILES. INCLUDE MY07 GT DIAMOND SERIES ALSO. *PE
BB-08-147
Service Bulletin/Repair Instructions
BENTLEY: CONTINENTAL SERIES-WHEEL BEARING RETAINING SCREW. SOME DEALERS HAVE STOCKS OF THE ORIGINAL FASTENING SCREW. LOOK AT BULLETIN #08-143. RETURN THEM USING THE SPR PROCESS. *PE
08-084
Service Bulletin/Repair Instructions
BENTLEY: WORKSHOP ACTION - CONTINENTAL SERIES - FUEL FILLER HOUSING - WATER DRAIN BLOCKED - WA08/05. ALL CONTINENTAL SERIES RANGE UP TO MODEL YEAR 2008. *PE
08-063
Service Bulletin/Repair Instructions
BENTLEY: 08MY CONTINENTAL SERIES; INCORRECT TIRE SIZE DISPLAYED. TIRE PRESSURE MONITORING (TPM) INFORMATION DISPLAY WAS ENHANCED AT 08MY. *PE
0510
Service Bulletin/Repair Instructions
SERVICE CAMPAIGN - CONTINENTAL SERIES - ELECTRONIC PARKING BRAKE (EPB), MEMORY PREMATURE AGING - SC05/10. *TT
74
Service Bulletin/Repair Instructions
TIRE PRESSURE MONITORING DIAGNOSIS. *TT
67
Service Bulletin/Repair Instructions
WINTER WHEELS AND TIRE ASSEMBLIES. *JB
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.