Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
2075786/1
Airbag, fire, accident (safety-related enquiry - reporting forms). There is a reporting obligation in the following cases: • Airbag/belt released/not released • General accident • Fire and scorching damage for all Bentley Vehicle models - every model year.
2077519/2
Exterior Gap and Profile Information | 17 - 25MY. Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.
2077529/2
Seat Fans Inoperative | All Models | 17-25MY. Condition: Customer may report that the seat ventilation system is not functioning with no airflow from the seat ventilation ducts.
2077519/1
Exterior Gap and Profile Information | 17 - 25MY. Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness
2077094/1
Earth Stud Anomalies | 25MY
2077529/1
Seat Fans Inoperative | All Models | 17-25MY
2077217/1
Incorrect wheel bolt cap kits (SC25/06). Technical background: On all affected vehicles the wheel bolt cover cap kit supplied in the dealer kit bag for specific BY636 25MY vehicles (wheel style dependant) do not fit the wheel bolts. Testing found that the cap kit 8w0.600.026.E was unsuitable and the caps do not fit on to the bolt. To fix this Bentley has reverted to current cap kit 36A.600.026.B.
2051187/11
Poor Engine Running Complaints (Misfires) Petrol Engines Only. Condition: • Poor engine running • Reduced power • Engine warning lamp illuminated • Symptom related DTC’s evident within the applicable engine control unit(s)
2077318/1
Bentayga, Continental GT/C and Flying Spur 25 Model Year - Garage Door Opener Programming Procedure.
2068273/4
Multiple random misfires evident during PDI. Condition: Multiple random cylinder misfire DTC’s detected during PDI - DTC P030000: Random/Multiple Cylinder Misfire Detected (misfires on multiple cylinders) within the following control units: • V8 - ECM 1 - V8 (Address 01) ECM control unit • W12 - ECM 1 - (Address 01) and/or ECM 2 (Address 11)
2071131/3
Measured values - Cycle recording instructions. Condition: In some cases, Measured value traces may be requested in XML format for analysis by Product Support
2028794/8
Engine coolant mixture - Restrictions on use of desalinated water. Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems Demineralised water according to standard VDE 0510 meets all requirements and can be purchased worldwide Therefore undiluted coolant should be mixed in the correct ratio using demineralised water as detailed in Elsa Pro coolant specification, this will detail the ratio and type of coolant to use The use of desalinated water in the engine cooling system is specifically prohibited
2057978/8
Engine Lubricating Oil - Replenishment. Condition: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires “topping up” between services.
2062365/5
Bentayga and New Flying Spur Hybrid - DTC P103A00 evident - Engine Oil Fuel Portion Too High. Customer statement: • Warning message within the DIP • The message asks the customer to ‘warm up engine’ accompanied by a yellow warning (Figure 1) No other symptoms are experienced.
2064337/3
Usage of E10 fuel. Condition: In the event a customer asks if E10 fuel can be used, the operative must refer to the Technical background section of this TPI Technical Background: Details on the introduction of E10 fuel which contains 10% ethanol and its usage on Bentley products • All vehicles produced post 1990 Model year can be run using E10 fuel However • All vehicles produced before 1990 Model year MUST NOT use E10 fuel
2028808/8
Service info: Engine oil - Specific oil type and oil consumption reference. Condition: Engine oil level requires top up between services Technical Background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering
2056407/6
Running gear - Noise identification. Customer statement: Noise complaint from the suspension and/or steering.
2063017/4
Road wheel inspection procedure. Condition: In the event a complaint is received regarding road wheel/s condition for example: • Scratches • Corrosion • Damage • Blemishes • Chipping
2063651/4
Tyre tread/sidewall crack(s)
2052785/9
Brake noise identification. Technical Background: Brake noises can be attributed to many causes, the most common causes are as follows: • Brake discs or pads are close to their wear limit • New brake pads and/or discs have not been properly bedded in after installation • Aftermarket pads or discs are installed • There is debris such as small stones, grit, road salt or sand between the brake disc and pad • Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time
2071131/2
Measured values - Cycle recording instructions. Technical background The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.