Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B340414
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B110208
Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
B013118
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
B011618
For the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.
B650709
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B011014
ENGINE CAMSHAFT (VANOS) ADJUSTMENT UNITS: BMW of North America, LLC (ÒBMW NAÓ) is extending the limited warranty for the Camshaft (VANOS) Adjustment Units on certain model BMW vehicles equipped with the non-turbocharged 6-cylinder engine
B080119
In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
B840314
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B840214
ConnectedDrive/BMW Assist System Diagnosis Information This Service Information bulletin replaces SI B84 02 14 dated July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
SIM010717
The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
B840311
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B070314
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B652616
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B012016
FOOTWELL MODULE: LIMITED WARRANTY EXTENSION TO 8 YEARS/125,000 MILES. When performing ISTA/D diagnosis and/or a programming procedure (software update) on an affected vehicle, the Footwell Module (FRM) could fail. There is a compatibility issue with certain combinations of vehicle software (Plant Integration ILevel) and the Footwell Module hardware installed in the vehicle.
B110616
N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B122110
N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
B130315
SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B650216
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B090615
New programming feature: Exclusion of Infotainment Control Units from Programming. Programming with ISTA/P 3.57.4, or a more recent update, displays a new Pop-Up window providing options for systems programming.
B650215
iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
B360215
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
070314
This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
650215
SiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion
120415
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
650509
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
840412
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
011014
Engine Camshaft (VANOS) Adjustment Units: Limited Warranty Extension to 10 Years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Camshaft (VANOS) Adjustment Units on certain model BMW vehicles equipped with the non-turbocharged 6-cylinder engine to: 10 years without mileage limitation, as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable New Vehicle/SAV Limited Warranty's exclusions and limitations, in addition to the vehicle and coverage eligibility requirements. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem.
121412
SI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke
122110
N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
280114
DCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
8403014
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
310109
Creaking or Groaning Noise During Compression and/or Rebound of Front Axle. A grating or groaning noise is heard when the front axle compresses and/or rebounds. This may be heard particularly over speed bump-type surfaces. The noise normally occurs at lower outside temperatures. The noise may be less prevalent when the vehicle has been driven up to the operating temperature.
010414
External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
641010
SI B64 10 10 Heating and Air Conditioning July 2014 Technical Service SUBJECT Howling/Rough Running Noise when the A/C Compressor is Engaged.
840214
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
840314
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
340313
Incorrect Remaining Service Life from CBS Data for Brake pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
360211
Tire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
650514
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
650314
RAD2+ Radio: Background Noise with Audio Turned Off. Background noise (buzzing, crackling, static) can be heard: * At low audio volume * When the radio is turned off * When the ignition is turned off NOTE: Background noise stops when the radio enters sleep mode. IMPORTANT: Background noise is more noticeable on vehicles produced before 09/2009 in case a RAD2+ replacement radio was installed previously. RAD2+ radio concept, manufactured from July 2009 to February 2014
840114
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
240413
GM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
630414
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
652513
ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST "My Info" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
513608
Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: "Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction," and then press "Start Search." Select the test plan "AM5102_00010."
651013
The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, "Replacing sensor mat (OC3 mat) for passenger seat occupancy detector." 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding.
651112
Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
340713
Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
010212
BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the "Vehicle Comment" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage.
130409
N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked ("wet") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the "N54 Engine Diagnostic Fault Tree" file (the current version "02_14_13" is found as a PDF attachment to SI B12 55 06).
651310
In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
840313
Roadside Assistance and BMW Online Services Inoperative After Programming. Roadside Assistance and BMW Online services are inoperative after programming the vehicle with ISTA/P 2.48 to 2.49.0. The symptoms are as follows: * BMW Online - No network available when selected * Roadside Assistance - When selected, a message stating "Service not enabled or contract expired" is displayed. Also, "Start service" is grayed out and cannot be selected. CAUSE Software error in the CIC (Car Information Computer)
121611
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
130213
N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
640313
IHKA Control Panel Not Working. IHKA (Integrated Automatic Heating and Air Conditioning) panel does not work or light up. CAUSE Fuse blown or chaffed wire for rear trunk light
650513
Basic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
SIB-11-03-08
BMW: CRANKCASE PRESSURE DIAGNOSIS AND INFORMATION FOR ALL VEHICLES. *RM UPDATED ON 4/24/2013. *KB
652012
RAD2plus: Radio Causes Battery Drain. The vehicle's battery state of charge is very low after the vehicle was parked for a longer period of time (e.g., overnight). The RAD2+ radio doesn't allow the vehicle to enter full sleep mode, and causes a current draw from the battery with ignition off.
122112
N51, N52K and N52T: Idle Fluctuation During Engine Warm-up Phase. After a cold engine start, the idle speed may be unstable or start fluctuating up and down slightly while the vehicle is stopped. On vehicles with automatic transmissions, roughness or shuddering may be felt during this warm-up period when diving away slowly in "D" or in "R" without depressing the accelerator pedal. No relevant errors are stored in the DME fault code memory, and these symptoms are no longer present once the engine is at operating temperature (> 90C). Unfavorable DME software
652212
Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
611305
Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the "Procedure" section of this Service Information for details.
651512
Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code "FSC CIC map, N. America 2013 INITIAL" is necessary to start the installation process and to activate the road map database.
SIB-36-02-11
BMW: CHANGES HAVE BEEN MADE TO THE VEHICLE¿S DISPLAY ELEMENTS OF THE TIRE PRESSURE MONITOR SYSTEM. *RM
SIB-63-02-01
BMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
SIB-32-04-07
BMW: A NEW TECHNICAL PROCESS HAS BEEN CREATED FOR BMW TO IDENTIFY CAUSES OF STEERING COMPLAINTS WITH A WIDE RANGE OF MODELS. *RM
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.