B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
Vehicle report
2012 BMW 328XI
Service bulletins
64 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B110208
Service Bulletin/Repair Instructions
Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
110208
Service Bulletin/Repair Instructions
Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is "late", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well.
B013118
Service Bulletin/Repair Instructions
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
B011618
Service Bulletin/Repair Instructions
TAKATA CLASS ACTION SETTLEMENT. CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.
B840214
Service Bulletin/Repair Instructions
ConnectedDrive/BMW Assist System Diagnosis Information This Service Information bulletin replaces SI B84 02 14 dated July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
SIM010717
Service Bulletin/Repair Instructions
The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
SIM010917
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
B840311
Service Bulletin/Repair Instructions
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
Service Bulletin/Repair Instructions
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
Service Bulletin/Repair Instructions
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B070314
Service Bulletin/Repair Instructions
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B652616
Service Bulletin/Repair Instructions
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B652516
Service Bulletin/Repair Instructions
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B012016
Service Bulletin/Repair Instructions
FOOTWELL MODULE: LIMITED WARRANTY EXTENSION TO 8 YEARS/125,000 MILES. When performing ISTA/D diagnosis and/or a programming procedure (software update) on an affected vehicle, the Footwell Module (FRM) could fail. There is a compatibility issue with certain combinations of vehicle software (Plant Integration ILevel) and the Footwell Module hardware installed in the vehicle.
B110616
Service Bulletin/Repair Instructions
N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
B840314
Service Bulletin/Repair Instructions
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B650216
Service Bulletin/Repair Instructions
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B650709
Service Bulletin/Repair Instructions
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
B090615
Service Bulletin/Repair Instructions
New programming feature: Exclusion of Infotainment Control Units from Programming. Programming with ISTA/P 3.57.4, or a more recent update, displays a new Pop-Up window providing options for systems programming.
B652606
Service Bulletin/Repair Instructions
The Disclaimer screen automatically disappears from the CID after 10 seconds. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/28...12/2/2015 Page 2 of 2 An enhancement was made to the Car Communication Computer (CCC) and MASK (Multi Audio System Controller) in 2006 so the customer does not have to manually accept the "Disclaimer" screen each time. Older vehicles prior to the production dates listed above that are programmed with ISTA/P 2.52 or higher will also get this enhancement. WARRANTY INFORMATION Not applicable.
B270415
Service Bulletin/Repair Instructions
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B640315
Service Bulletin/Repair Instructions
Air Conditioning Cooling is Insufficient or Inoperative. The air conditioner system refrigerant level is low or empty. CAUSE The evaporator is leaking refrigerant.
B650215
Service Bulletin/Repair Instructions
iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
B360215
Service Bulletin/Repair Instructions
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
070314
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
650215
Service Bulletin/Repair Instructions
SiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion
650509
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
840412
Service Bulletin/Repair Instructions
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
121412
Service Bulletin/Repair Instructions
SI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke
8403014
Service Bulletin/Repair Instructions
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
611714
Service Bulletin/Repair Instructions
Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is "aged." When energy diagnosis identifies the battery as "aged," it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, "07 Battery Basics."
010414
Service Bulletin/Repair Instructions
External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
610314
Service Bulletin/Repair Instructions
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
641010
Service Bulletin/Repair Instructions
SI B64 10 10 Heating and Air Conditioning July 2014 Technical Service SUBJECT Howling/Rough Running Noise when the A/C Compressor is Engaged.
840214
Service Bulletin/Repair Instructions
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
840314
Service Bulletin/Repair Instructions
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
340313
Service Bulletin/Repair Instructions
Incorrect Remaining Service Life from CBS Data for Brake pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
360211
Service Bulletin/Repair Instructions
Tire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
360309
Service Bulletin/Repair Instructions
Third Generation Tire Pressure Monitor System (RDC). INFORMATION As of September 2009 production, a new generation Tire Pressure Monitor System has been introduced for all 3 Series models. Although the basic operation of the system is similar to the previous version, there are several key differences between the two systems. The new system consists of five components: One central antennae with an integrated control module (5) mounted in the right rear wheel arch Four wheel electronics (1-4) mounted at the base of each tire valve. Central antennae with integrated control module The control module and central antennae have been combined in a single housing. This new control module has the ability to send requests for information to each of the 4 wheel New style wheel electronics The wheel electronics consist of a plastic housing with integrated circuitry. The following items are contained within the wheel electronics: Pressure sensor Temperature sensor Acceleration sensor Transmitter/receiver unit Self-diagnosis controller Battery The following points should be considered when diagnosing and/or servicing the system: * The system components are not interchangeable or compatible with previous versions. * The type of wheel electronic fitted can only be determined via visual inspection. * The detection of low tire pressure and the subsequent warning is similar to the previous design. * The reset procedure has changed. Special Note for Reset Procedure After initiating a reset, the vehicle must be driven for a period longer than 12 minutes with a vehicle speed which exceeds 19 mph (~30 km/h). WARRANTY INFORMATION Not applicable.
630714
Service Bulletin/Repair Instructions
One or Both Xenon Headlights Aiming Downwards. CAUSE Both sides are aiming downwards: * The most likely cause is a faulty or disconnected rear height sensor. In very extreme cases due to poor road conditions, both headlight assemblies could have the vertical aim ball socket adjuster disconnected, as noted below. Only one side is aiming downwards: * The cause could be a "disconnected" vertical aim ball socket adjuster, resulting from excessive road vibration or sharp impacts (pot holes) through the suspension to the headlight assembly. Important Note: Follow the procedure outlined in this bulletin first; replacing headlight assemblies for a vertical aim ball socket adjuster issue is an excessive repair.
650514
Service Bulletin/Repair Instructions
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
650314
Service Bulletin/Repair Instructions
RAD2+ Radio: Background Noise with Audio Turned Off. Background noise (buzzing, crackling, static) can be heard: * At low audio volume * When the radio is turned off * When the ignition is turned off NOTE: Background noise stops when the radio enters sleep mode. IMPORTANT: Background noise is more noticeable on vehicles produced before 09/2009 in case a RAD2+ replacement radio was installed previously. RAD2+ radio concept, manufactured from July 2009 to February 2014
840114
Service Bulletin/Repair Instructions
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
240413
Service Bulletin/Repair Instructions
GM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
510807
Service Bulletin/Repair Instructions
Erroneous Trunk Lid Open Check Control Message. The trunk open check control message may appear, even though the trunk lid or tailgate is fully closed and latched. CAUSE Incorrect adjustment of the trunk latch striker
612906
Service Bulletin/Repair Instructions
ELV Does Not Release. Cause 1: The steering column is held against the steering lock because of torque from the steering gear. In such cases, a yellow check control warning (CC ID# 187) is shown in the instrument cluster, but no faults are stored. Cause 2: Communication fault in the CAS (Car Access System) and ELV system network and/or battery low. The problem may cause the ELV warning to be displayed in yellow or red.
630414
Service Bulletin/Repair Instructions
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
652513
Service Bulletin/Repair Instructions
ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST "My Info" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
513608
Service Bulletin/Repair Instructions
Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: "Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction," and then press "Start Search." Select the test plan "AM5102_00010."
515510
Service Bulletin/Repair Instructions
SI B51 55 10 November 2013 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B51 55 10 dated December 2010. designates changes to this revision SUBJECT Rear Window Release Button Leaks Water.
651013
Service Bulletin/Repair Instructions
The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, "Replacing sensor mat (OC3 mat) for passenger seat occupancy detector." 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding.
651112
Service Bulletin/Repair Instructions
Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
340713
Service Bulletin/Repair Instructions
Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
541309
Service Bulletin/Repair Instructions
?Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several "mechanism sets" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP.
651310
Service Bulletin/Repair Instructions
In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
650513
Service Bulletin/Repair Instructions
Basic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
652012
Service Bulletin/Repair Instructions
RAD2plus: Radio Causes Battery Drain. The vehicle's battery state of charge is very low after the vehicle was parked for a longer period of time (e.g., overnight). The RAD2+ radio doesn't allow the vehicle to enter full sleep mode, and causes a current draw from the battery with ignition off.
122112
Service Bulletin/Repair Instructions
N51, N52K and N52T: Idle Fluctuation During Engine Warm-up Phase. After a cold engine start, the idle speed may be unstable or start fluctuating up and down slightly while the vehicle is stopped. On vehicles with automatic transmissions, roughness or shuddering may be felt during this warm-up period when diving away slowly in "D" or in "R" without depressing the accelerator pedal. No relevant errors are stored in the DME fault code memory, and these symptoms are no longer present once the engine is at operating temperature (> 90C). Unfavorable DME software
650110
Service Bulletin/Repair Instructions
CCC - "Please Insert Navigation DVD" Appears on CID. The navigation map DVD cannot be read or detected. The message "Please insert navigation DVD" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head
511508
Service Bulletin/Repair Instructions
?SI B51 15 08 Body Equipment October 2012 Technical Service. This Service Information bulletin supersedes SI B51 15 08 dated July 2008. designates changes to this revision SUBJECT Rear Window False Anti-trap Activation. INFORMATION The anti-trap protection feature may be activated when no obstruction is present. This may occur at either one or both of the rear windows. The root cause of the false anti-trap activation may be difficult to determine. The attached diagnosis flowchart has been developed to assist with determining the actual root cause of the failure as well as to help prevent unnecessary part replacements. The root cause is typically either an issue with the window system, or an electrical/software issue. The diagnosis flowchart will help ensure that repairs are only carried out for the system that is most likely at fault. Refer to B511508_Attachment. PARTS INFORMATION Refer to the Electronic Parts Catalog (EPC) for the appropriate parts noted in the diagnostic flowchart. WARRANTY INFORMATION Not applicable.
611305
Service Bulletin/Repair Instructions
Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the "Procedure" section of this Service Information for details.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.