B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
Vehicle report
2012 BMW 335IS
Service bulletins
18 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B610322
Service Bulletin/Repair Instructions
The footwell module (FRM) cannot be encoded after replacement.
B011321
Service Bulletin/Repair Instructions
CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
B340414
Service Bulletin/Repair Instructions
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B110208
Service Bulletin/Repair Instructions
Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
B130619
Service Bulletin/Repair Instructions
SERVICE ACTION: N54T ENGINE - INSPECT AND REPLACE INJECTOR(S). The piezo-type fuel injectors may cause a rough running at start-up or rough running while at idle.
651512
Service Bulletin/Repair Instructions
Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
513608
Service Bulletin/Repair Instructions
Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
613312
Service Bulletin/Repair Instructions
Erroneous CC Message Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"
110208
Service Bulletin/Repair Instructions
Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is "late", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well.
121412
Service Bulletin/Repair Instructions
N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
B540907
Service Bulletin/Repair Instructions
RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. This Service Information bulletin replaces SI B54 09 07 dated September 2018.
B013118
Service Bulletin/Repair Instructions
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
B011618
Service Bulletin/Repair Instructions
TAKATA CLASS ACTION SETTLEMENT. CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.
SIM010717
Service Bulletin/Repair Instructions
The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
SIM010917
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
540412
Service Bulletin/Repair Instructions
Retractable Hard Top (RHT) Is Not Stacking Properly - Frame Bent. The RHT frame is bent or twisted and cannot be operated in either direction, or the roof shells are not stacking properly. The hydraulic roof cylinders operate out of sequence causing the frame to twist.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.