Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B720125
Warranty Program/Extension
A situation may occur where the front passenger seat is not occupied; however, a “fasten seat belt” warning and a front passenger seat air bag deactivation message appears. If the situation is currently present, sit in the seat and move the seat to a slightly different position. The POL (Passenger Occupancy Light) light should now function correctly. In some cases, the Air bag Warning Light was illuminated, and the following Advanced Crash Safety Module (ACSM) fault is stored: 930A1C - Front passenger seat occupancy detection transmitting fault (moisture)
B010324
Warranty Program/Extension
EVAP SYSTEM PURGE (VENT) VALVE EXT LTD WTY (ELW) 15/150
B630418
Service Bulletin/Repair Instructions
One or more of the LED daytime running lights are dim or discolored.
B120721
Service Bulletin/Repair Instructions
Check Control message (CCM) indicates: (ID 213): Stop, exercising due care. Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt betweenCombustion engine and starter generator torn And/or one or more of the following other issues are also occurring: Noise in the area of the belt drive. Odor from the engine compartment. Smoke formation in the area of the belt drive. Drive belt damaged or prematurely worn. Torn drive belt.
B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B360121
Service Bulletin/Repair Instructions
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned. This can be felt (jerking)/ heard via an acoustic acknowledgement (clunk) as seen at the 11 second mark of the video. See attached video V36 01 21.
B610524
Service Bulletin/Repair Instructions
The Central Information Display goes black intermittently due to resets of the Head Unit (HU-H3). FaultB7F8F9 ÃÂâÃÂÃÂÃÂàÃÂâÃÂÃÂÃÂÃÂHU-H: ResetÃÂâÃÂÃÂÃÂàwill be stored in the HU-H3.
B320223
Service Bulletin/Repair Instructions
SITUATION Unusual noises occur only when operating the steering column in the axial direction. 1. A one-time thump sound at the start of movement Shortly after the steering column starts moving, retracting, or extending, a one-time thump noise is heard. See attached video V32 03 23 2. Humming noise while steering column extends in the axial direction. The sound is only heard when the steering column is extended, not when the steering column is retracted. When the steering column starts to move in the extended direction, the humming noise can be heard. See attached video V32 04 23
B160623
Service Bulletin/Repair Instructions
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
B653423
Service Bulletin/Repair Instructions
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
B010919
Service Bulletin/Repair Instructions
DIESEL FUEL INJECTORS: LTD WTY EXTENSION TO 10 YEARS/120,000 MILES
B011423
Service Bulletin/Repair Instructions
PRESSURE CONTROL VALVE (PCV) EXTENDED LTD WTY 15 YEARS/150,000 MILES
B520121
Service Bulletin/Repair Instructions
?The front seat will not calibrate/initialize, and the stored faults cannot be deleted.
B540521
Service Bulletin/Repair Instructions
?The sunroof will not operate in either direction.
B011219
Service Bulletin/Repair Instructions
Radiator Grille Upper and Lower Active Air Flaps limited warranty for defects in materials or workmanship has been extended to 15 years/150,000 miles as determined from the original in-service date.
B090221
Service Bulletin/Repair Instructions
With the introduction of the BMW Remote Software Upgrade, all Service Pack 18 vehicles and partial Service Pack 15 vehicles may receive new functionality or modifications in their features.
B120323
Service Bulletin/Repair Instructions
BMW AG has issued a Delivery Stop effective June 6, 2023 on certain Model Year 2023 - 2024 BMW vehicles that were produced between October 26, 2022 and May 8, 2023.
B160123
Service Bulletin/Repair Instructions
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system (NVLD natural vacuum leak detection). For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5 mm.
B320420
Service Bulletin/Repair Instructions
A groaning type noise is heard during the height adjustment.
B630821
Service Bulletin/Repair Instructions
Headlight check control (CC) message 128 "High beam headlight failure" is displayed. The following fault codes are stored during a vehicle test: 80419A - Left high-beam headlight: Short circuit and/or 8041A5 - light outputs: Number of permitted short circuit cycles exceeded
B640821
Service Bulletin/Repair Instructions
The air conditioning cycles from cold to warm air while driving or while at a stand still. The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings.
B514616
Service Bulletin/Repair Instructions
Upon opening and closing the tailgate, a creaking/groaning sound can be heard from tailgate actuator.
B610123
Service Bulletin/Repair Instructions
Due to a software error, the vehicle sporadically does not achieve sleep mode. As a result, the 12-volt battery becomes discharged and may cause a no-start condition.
B651523
Service Bulletin/Repair Instructions
After programming the head unit (HU-H2), activating the FSC (German word Freischaltcode) Enabling Codes repeatedly fails.
SIB660823
Service Bulletin/Repair Instructions
Issues with the various functions of the camera-based driver assistance systems (KAFAS system) can possibly lead to following customer complaints: KAFAS camera system deactivates itself, due to system restrictions that are not clear to the customer KAFAS camera system cannot be activated due to system restrictions that are not clear to the customer Road signs are sporadically not detected.
B240223
Service Bulletin/Repair Instructions
BMW AG has issued a Delivery Stop: Due to a software failure, there is the possibility that the transmission does not go into "sleep mode" if the car is turned off.
B260422
Service Bulletin/Repair Instructions
There is a howling or whistling noise from under the vehicle at 30 -37 mph (50 -60 km/h) when driving after a cold start, when the outside temperature is 32 F (0 C) or lower.
B651623
Service Bulletin/Repair Instructions
Customer states there is no audio playback (telephony, navigation, radio) and system sounds (PDC, turn indicators, acoustic signals) may also have failed.
B840822
Service Bulletin/Repair Instructions
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
B841422
Service Bulletin/Repair Instructions
Customer is shown an incorrect GPS location in the vehicle (i.e., Nav Map, coordinates).
B170617
Service Bulletin/Repair Instructions
Coolant leaking from the engine compartment. Traces of coolant leaking from the expansion tank of the low temperature cooling system.
B240222
Service Bulletin/Repair Instructions
A cracking, metallic noise from under the center of the vehicle.
B612922
Service Bulletin/Repair Instructions
The saved steering column positions, vertical and horizontal, are not stored long term.
B613322
Service Bulletin/Repair Instructions
Due to a software error, Remote Software Upgrade (RSU) and Remote Support are currently not possible. Additionally, the Integrated Owner's Handbook cannot be displayed.
B611222
Service Bulletin/Repair Instructions
After opening the vehicle with the radio remote control and changing the profile, the exterior mirror settings are lost.
B620322
Service Bulletin/Repair Instructions
After programming, the customer may complain that the Sport Mode display is not fully displayed in the instrument cluster. Instead of a red background in sport mode, the background is displayed in blue (like ECO PRO mode).
B650414
Service Bulletin/Repair Instructions
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B651922
Service Bulletin/Repair Instructions
The customer complains that the radio stations change by themselves.
SIB010119
Service Bulletin/Repair Instructions
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Radiator Grille Upper and Lower Active Air Flaps to: 10 years/120,000 miles as determined by the vehicle's original in-service date. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Air flap issues caused by debris/blockage from outside influences is not a defect in materials or workmanship and is not claimable. During the extended limited warranty coverage period (Eligible vehicles that are beyond the 4 year/50,000 mileage New Vehicle Limited Warranty coverage), Active Air Flap cosmetic defect issues are not covered. 1. Air flap control (link), active, upper (G12, G30) 1. Air flap control (drive), active, upper. 2. Air flaps, upper (assembly). 3. Air flaps, lower (assembly).
SIB650922
Service Bulletin/Repair Instructions
The sound output intermittently drops out entirely. This can be reproduced with all audio sources as well as telephone and voice output.
SIB010121
Service Bulletin/Repair Instructions
Note: Before performing a repair and submitting a claim, first confirm that the vehicle has the above Notice of Limited Warranty Extension in the DCSnet Warranty Inquiry Vehicle Comments section. If you have Extended Limited Warranty (ELW) eligibility and/or coverage questions, please contact the Warranty department through IDS by selecting Coverage, Policy, Coding Questions and Mileage Corrections prior to performing any repair.
SIB090121
Service Bulletin/Repair Instructions
BMW offers a new special ISTA Installation made available for Roadside Assistance / Mobile Service technicians. The new ISTA Version is also able to be used in case of a Remote Software Upgrade (RSU) programming failure to get the customer car reprogrammed on site. In case of a Remote Software Upgrade failure, the engine start is prevented for safety reasons until the vehicle is programmed correctly. Most of the errors occur when only one control unit fails to program correctly.
SIB610222
Service Bulletin/Repair Instructions
BMW AG is conducting a Voluntary Service Action on certain Model Year 2019-2020 BMW Plug-In HybridElectric (PHEV) vehicles that were produced between March 25, 2019, and October 17, 2020. Analyses of transmitted teleservice data indicate abnormalities in the "balancing" of the cells within one or more of the high-voltage battery cell modules. This could possibly cause a loss of performance of the corresponding modules, such as faster ageing, shorter range, or possible operating failure.
SIB610722
Service Bulletin/Repair Instructions
Check Control Message (CCM) displays "Vehicle key missing" after engine start.
SIB610822
Service Bulletin/Repair Instructions
When using the Key Reader to retrieve information from the customer's key, no current vehicle data is available.
SIB651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
SIB660820
Service Bulletin/Repair Instructions
The functionality of the right rear SRR sensor could be reduced which would display the "Driving Assistance" Check Control Message.
B110521
Service Bulletin/Repair Instructions
The belt pulley on the mechanical coolant pump may fracture allowing the engine drive belt to come off the coolant pump and alternator.
B110621
Service Bulletin/Repair Instructions
Information updated about engine oil filter cap drain plug. When performing an engine oil service on vehicles equipped with a N63M, N63B or S63M engines; the ETK states to use "Set oil filter element" P/N 11 42 5 A33 C42 or P/N 11 42 5 A33 C43. The part numbers are not available at the moment.
B121021
Service Bulletin/Repair Instructions
The customer complains that under moderate throttle application or on deceleration after throttle application, a Malfunction Indicator Lamp (MIL) is displayed in the instrument cluster.
B610121
Service Bulletin/Repair Instructions
48 V battery may become totally discharged, and possible replacement needed.
B610722
Service Bulletin/Repair Instructions
Check Control message (CCM) displays "Vehicle key missing" after engine start.
B620222
Service Bulletin/Repair Instructions
Sport mode is not displayed correctly in the instrument cluster. Instead of a red background in sport mode, the background is displayed in blue (like in Eco Pro mode). Software in the instrument cluster (Kombi).
B640322
Service Bulletin/Repair Instructions
No heater output in passenger area.
B661519
Service Bulletin/Repair Instructions
The steering intervention for Lane Departure Warning (LDW) is too strong (severe), which can create an uncomfortable feeling for the driver. Background: Steering intervention helps keep the vehicle in the lane if the system detects that a lane marking has been crossed. The steering intervention can be noticed on the steering wheel and can be manually overridden at any time.
B090321
Service Bulletin/Repair Instructions
In some rare cases a customer vehicle might be excluded from one or more Remote Software Upgrade(RSU) campaigns. This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint.
B170121
Service Bulletin/Repair Instructions
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
B610222
Service Bulletin/Repair Instructions
BMW AG is conducting a Voluntary Service Action on certain Model Year 2019-2020 BMW Plug-In Hybrid-Electric (PHEV) vehicles that were produced between March 25, 2019, and October 17, 2020.
B651221
Service Bulletin/Repair Instructions
BMW AG has issued a Delivery Stop (effective June 9, 2021) on certain Model Year 2021 BMW vehicles that were produced between May 7, 2021 and May 21, 2021. The Receiver Audio Module (RAM) will need to be added to the affected vehicles.
B620122
Service Bulletin/Repair Instructions
Temporary black screen in the instrument cluster.
B652121
Service Bulletin/Repair Instructions
SiriusXM satellite radio is not working and does not display a channel list.
B662419
Service Bulletin/Repair Instructions
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B840621
Service Bulletin/Repair Instructions
The SIM card installed in the telematics control unit (ATM2) connects to different mobile providers' networks. However, due to a missing parameter, this does not work and can cause disruption in BMW ConnectedDrive services in areas with insufficient network coverage.
B840917
Service Bulletin/Repair Instructions
While using the wireless charger, one or both of the following may occur: 1) The BMW display key or mobile phone becomes hot to the touch. 2) The device switches off due to over temperature (built-in device protection).
B001020
Service Bulletin/Repair Instructions
BMW of North America (BMW NA) has made information available online to customers about software versions, including any changes to vehicle functionality that will result from each update.
B090121
Service Bulletin/Repair Instructions
BMW offers a new special ISTA Installation made available for Roadside Assistance / Mobile Service technicians.
B121121
Service Bulletin/Repair Instructions
???When charging the vehicle with an Occasional Use Charger (OUC) after previously using a Wallbox charger, the selected charging current might not be displayed correctly in the instrument cluster.
B121221
Service Bulletin/Repair Instructions
???Due to an unfavorable operating point primarily in the low-end torque range, the fuel vapor scavenging that takes place in that range may result in incorrect detection of a mixture that is too rich. As a result, an incorrect mixture adaptation value is stored.
B511921
Service Bulletin/Repair Instructions
A faulty componnent inside the trunk spindle drive.
B611421
Service Bulletin/Repair Instructions
The BMW Gesture Control function may fail permanently as a result of high temperature fluctuations.
B611621
Service Bulletin/Repair Instructions
The "energy management" Check control message (ID code 415) is falsely displayed when entering the vehicle.
B650919
Service Bulletin/Repair Instructions
Customer states the following about their vehicle: active radio or music source is interrupted, the navigation is no longer available, a black screen is shown in the Control Display, the system works again after a short interruption.
B120821
Service Bulletin/Repair Instructions
When charging the vehicle with an Occasional Use Charger (OUC) after previously using a Wallbox charger,the selected charging current might not be displayed correctly in the instrument cluster.
B511314
Service Bulletin/Repair Instructions
The trunk lid/hatch does not open fully when unlatched with remote or hands-free operation.
B610721
Service Bulletin/Repair Instructions
Groaning, scraping, or squeaking noise coming from the steering wheel area in the interior of the vehicle,when turning the steering wheel.
B640721
Service Bulletin/Repair Instructions
Only warm air comes out of the vents despite the air conditioning being switched on. The status indicator LED on the air conditioning control panel (IHKA) lights up green.
B651721
Service Bulletin/Repair Instructions
The BMW key card cannot be activated. The activation menu in the BMW iDrive is missing.
B662919
Service Bulletin/Repair Instructions
The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both.
SIB 61 01 21
Service Bulletin/Repair Instructions
48 V battery may become totally discharged, and possible replacement needed if: a) The vehicle has been charged using a 12 V charger with the hood closed during a long stationary period, the. For example, the showroom or storage. b) Vehicles stored for an extended period connected to a low output solar or trickle charger. c) Vehicles stored for an extended period with no charger connected and not properly maintained 12 V battery.
SIB 61 04 21
Service Bulletin/Repair Instructions
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function.
SIB 61 09 21
Service Bulletin/Repair Instructions
Check control message (CCM-ID 49) "You can continue driving. Drivetrain". In addition, the following information is shown on the Central Information Display (CID): "You can continue to drive. No roadside assistance necessary. To avoid subsequent damage, arrange an appointment with your Service Partner".
SIB 62 03 21
Service Bulletin/Repair Instructions
When the vehicle is operated in Sport Mode, the engine speed is no longer displayed in the BMW Head-Up Display (HUD).
SIB120421
Service Bulletin/Repair Instructions
A software optimization affecting vehicle performance has been made available.
B110120
Service Bulletin/Repair Instructions
On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing.
B512219
Service Bulletin/Repair Instructions
Upon visual inspection, the passenger side upper active air flaps are either stuck open or closed, and they will not move.
B520621
Service Bulletin/Repair Instructions
The driver's seat and/or passenger seat rattles ("cracking" noise) during load reversal. There is a slight movement in the seat that is most noticeable when moving forwards and backwards.
B610421
Service Bulletin/Repair Instructions
The customer may complain of a check control message stating "Safe share detected" (CCM-ID 953). Check control message can be verified by checking key reader information or performing the Check control message history service function.
B612420
Service Bulletin/Repair Instructions
Some of the vehicles listed above which were initially identified as requiring Recall Campaign 20V-601 - HIGH VOLTAGE BATTERY to be performed and completed are now no longer included in this Recall.
B620221
Service Bulletin/Repair Instructions
The total electrically driven miles are lost/reset after the vehicle is programmed. This does not affect the total vehicle odometer reading.
B651121
Service Bulletin/Repair Instructions
SiriusXM satellite radio is not working and does not display a channel list.
B110321
Service Bulletin/Repair Instructions
B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
B650721
Service Bulletin/Repair Instructions
HU-H3 MGU RESETS DUE TO BLUETOOTH CONNECTION WITH SAMSUNG ANDROID 11 : The head unit resets when using various apps (e.g., YouTube, Spotify, etc) on the connected mobile phone. This affects Samsung mobile phones (e.g., Galaxy S20 / S21) with the Android 11 operating system.
B660321
Service Bulletin/Repair Instructions
DELIVERY STOP: RADIO REMOTE CONTROL M SPORT: Vehicles were delivered with the wrong radioremote control (without motion sensor) whichdecreases the theft-proofing against rangeextenders.
B840120
Service Bulletin/Repair Instructions
BMW CONNECTEDDRIVE SERVICES ARE NOT AVAILABLE: The BMW ConnectedDrive services are not available for an extended period.
B840220
Service Bulletin/Repair Instructions
REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App.
B650421
Service Bulletin/Repair Instructions
RETROFIT SATELLITE RADIO (OPTION CODE SA655): The affected vehicles were produced with Preparation BMW Satellite Radio (option code SA 693) instead of with Satellite Radio (option code SA 655).
B090120
Service Bulletin/Repair Instructions
BMW REMOTE SOFTWARE UPGRADE IS NOT OFFERED FOR INSTALLATION: The customer complains that the BMW Remote Software Upgrade (RSU) is not possible in his/her vehicle, though the Remote Software Upgrade menu is available in the vehicle and a download was performed by the vehicle or the BMW Connected App.
B620818
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER DISPLAY SHAKES-SHIFTS TO THE LEFT: The Instrument cluster intermittently flickers, shakes and has shifted to the left.
B630221
Service Bulletin/Repair Instructions
REAR LIGHT FAULTY CHECK CONTROL MESSAGE: The CID displays "Left brake light faulty.
B630421
Service Bulletin/Repair Instructions
AUTOMATIC HIGH BEAM DOES NOT DIM AUTOMATICALLY: The automatic high beams may not automatically dim to low beams.
B660121
Service Bulletin/Repair Instructions
REMOTE-CONTROL PARKING FAILS AFTER ENGINE START: When trying to park the vehicle using remote-control parking, the function fails after engine start.
B121318
Service Bulletin/Repair Instructions
COMBUSTION CONTROL VALVE LIFT AT IDLE: The vehicle will run rough or hesitate when accelerating from a stationary position.
B630121
Service Bulletin/Repair Instructions
BRAKE LIGHT REMAINS LIT AFTER BRAKE PEDAL RELEASE: The trunk-mounted brake light remains lit for several seconds after the brake pedal is released.
B650121
Service Bulletin/Repair Instructions
SPORADIC FAILURE OR CRACKING NOISE IN BASS SPEAKERS: No Bass or a cracking noise can be heard from the bass speakers.
B340121
Service Bulletin/Repair Instructions
DYNAMIC STABILITY CONTROL (DSC) UNIT DOES NOT RESPOND AFTER PROGRAMMING: After programming the vehicle using ISTA, the DSC control unit does not respond. Or: In the case of a BMW Remote Software Upgrade, the customer gets a Check Control message: "BMW Remote Software Upgrade failed. Vehicle is not operational. Please call BMW Roadside Assistance."
B612720
Service Bulletin/Repair Instructions
CHECKING THE JUMP START POINT COVER AND REWORKING IF NECESSARY: It is possible that the jump start terminal point cover was not installed, or not properly installed on the affected vehicles.
B121320
Service Bulletin/Repair Instructions
REPLACE ALL THE IGNITION COILS: The ignition coils may not have been produced to specifications which could lead to irregular running of the engine. A manufacturing defect affecting the ignition coil insulation.
B612520
Service Bulletin/Repair Instructions
REMOTE CONTROL KEY OR BMW DISPLAY KEY BUTTONS NOT WORKING: The buttons on the remote-control key or BMW display key are not working, not allowing to unlock the vehicle and the tailgate or trunk compartment. Also, the buttons on a spare key do not work either.
B612620
Service Bulletin/Repair Instructions
?BMW DIGITAL KEY CARD IS NOT DETECTED WHEN PLACED ON THE NFC TRAY: The customer may have the following complaints: The Digital Key Card cannot be activated on the NFC (near field communication) charging tray (the activation pop-up does not appear although the Digital Key menu is present), Or the Digital Key Card is not detected when placed on the NFC tray.
B620320
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) IS ILLUMINATED WITH FAULT MEMORY CDC152: The malfunction indicator lamp (MIL) is illuminated in the instrument cluster. The vehicles has no operating failures; only the MIL is illuminated.
B640617
Service Bulletin/Repair Instructions
?AIR CONDITIONING COOLING IS INSUFFICIENT: There is insufficient or no cooling from the air-conditioner during high ambient temperatures. There also may be irregular A/C air flow from vents.
B652020
Service Bulletin/Repair Instructions
?PROGRAM HEAD UNIT: Satellite radio content is not available over IP, this does not affect channels received over satellite.
B661820
Service Bulletin/Repair Instructions
?GESTURE CONTROL UNINTENDED OPERATION: The Gesture camera inadvertently detects movement and performs unintended operations.
B512720
Service Bulletin/Repair Instructions
FUEL FILLER DOOR WILL NOT OPEN: The fuel filler door (aka flap) will not open. In rare cases, if the vehicle is locked using the remote control key and the fuel filler door is pushed closed simultaneously, the fuel door can enter a locked state that cannot be unlocked.
B612315
Service Bulletin/Repair Instructions
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.
B651720
Service Bulletin/Repair Instructions
SERVICE ACTION - INSTALL GROUND STRAP / SUPPRESSOR BELT: Corrosion developing on the rear suspension contact points can lead to poor radio reception over a certain duration of time.
B661520
Service Bulletin/Repair Instructions
ACTIVE CRUISE CONTROL - UNEXPECTED DECELERATION: Vehicle slows down (decelerates) unexpectedly while Active Cruise Control with Stop & Go (ACC) function is activated.
B661720
Service Bulletin/Repair Instructions
SURROUND VIEW - PARKING VIEW IMAGES DISPLAYED INCORRECTLY: After programming and shifting into reverse, there may be various sporadic concerns regarding the rearview camera and the surround view (top view) camera images in the CID (Central Information Display).
B660720
Service Bulletin/Repair Instructions
SERVICE ACTION - REPLACE LEFT REAR SHORT RANGE RADAR SENSOR (SRR): The functionality of the left rear SRR sensor could be reduced which would display the Driving Assistance Check Control Message.
B660820
Service Bulletin/Repair Instructions
SERVICE ACTION - REPLACE RIGHT REAR SHORT RANGE RADAR SENSOR (SRR): The functionality of the right rear SRR sensor could be reduced which would display the Driving Assistance Check Control Message.
B320320
Service Bulletin/Repair Instructions
FAILURE OF THE ELECTRIC STEERING COLUMN ADJUSTMENT AT HIGHER CABIN TEMPERATURE: Electric steering column adjustment fails when interior cabin temperatures rise above 122 degrees F (e.g., parked outdoors on hot day). Faulty self-diagnosis of the steering column control unit.
B611820
Service Bulletin/Repair Instructions
BMW TURBOCORD PORTABLE EV 120 V/240 V CHARGER: The BMW-approved accessory TurboCord electric vehicle (EV) charger will not charge the vehicle.
B122219
Service Bulletin/Repair Instructions
EME GROUND CONNECTION MONITORING FAULTS: Check Control message (CCM ID 794): "Drive. Check as soon as possible" illuminates. Increased ground cable contact resistance at Electrical Machine Electronics (EME) due to corrosion/oxidation.
B511818
Service Bulletin/Repair Instructions
DOORS WILL NOT COMPLETELY LATCH: One or more doors will not completely latch or will open to the first stage at times. The door lock strikers may be misadjusted.
B611720
Service Bulletin/Repair Instructions
DELIVERY STOP - HIGH-VOLTAGE BATTERY: Please do not charge the vehicle high-voltage battery until further notice. There may be a potential issue in the welding process of the HV-modules.
B651520
Service Bulletin/Repair Instructions
HEAD UNIT RESETS WHEN NAVIGATION IS USED IN CERTAIN LOCATIONS: The head unit resets sporadically causing the CID to turn black and then starts up again after a short time with the message "Start navigation system". This only occurs during navigation guidance when the "3D building" function is used Software in the Head Unit High (HU-H3).
B661919
Service Bulletin/Repair Instructions
COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery.
B340517
Service Bulletin/Repair Instructions
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B512119
Service Bulletin/Repair Instructions
ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: Potential causes include: Faulty upper air flap actuator (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02 only).
B610419
Service Bulletin/Repair Instructions
VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
B620119
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: The audio source, radio station, or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. This affects vehicles with: Integration level S18A-18-11-5xx Live Cockpit Professional (option code 6U3) including the instrument cluster High 4.1. While the Kombi is not working properly the rest of the system is working properly. The customer can still use the Central Information Display (CID) for items such as entertainment settings, Driver Experience settings, etc, utilizing the I drive controller. The telephone functions are not affected. Unfavorable software at system start-up.
B620120
Service Bulletin/Repair Instructions
SERVICE ACTION - PROGRAM THE INSTRUMENT CLUSTER: The Condition Based Service (CBS) data concerning the due date for the brake fluid change may be displayed incorrectly. Software error in the Instrument Cluster (KOMBI).
B650709
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B651220
Service Bulletin/Repair Instructions
BMW CONNECTEDDRIVE APPS ARE NO LONGER AVAILABLE AFTER PROGRAMMING: After programming vehicle with "20-03" software, BMW ConnecedDrive apps are no longer available in the head unit. Software in the Head Unit High (HU-H3).
B840420
Service Bulletin/Repair Instructions
SERVICE ACTION - PROGRAM TELEMATICS MODULE: A software error in the telematics control unit can result in an interruption in communication between the vehicle and the back end (BMW server). Software error in the Advanced Telematics Module (ATM).
B170420
Service Bulletin/Repair Instructions
COOLANT LEVEL CHECK AND TOP-OFF AT SECOND OIL SERVICE: A new, additional coolant level check task is now linked to the second engine oil service (Service Counter 2 only). The scope of maintenance work will display in ISPA Next that applies to the high-temperature circuit. This new coolant check only pertains to the above listed models with gasoline engines. During the normal operation of the vehicle, there is a certain amount of coolant absorption by the various components/gaskets/seals contained within the coolant systems. Over time, the coolant absorption can cause the coolant level to fall below the maximum fill level in the reservoir. In some cases, the level may even fall low enough to cause the high-temperature circuit low coolant level warning light to illuminate, along with displaying the corresponding Check Control message.
B010119
Service Bulletin/Repair Instructions
FRONT GRILLE UPPER/LOWER AIR FLAPS - LTD WTY EXT TO 10 YRS/120000 MILES: Component-Specific Limited Warranty Extension For the eligible vehicles BMW of North America LLC (BMW NA) is extending the limited warranty for the vehicle's Radiator Grille Upper and Lower Active Air Flaps to: 10 years/120000 miles as determined by the vehicle's original in-service date.
B130420
Service Bulletin/Repair Instructions
TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.
B270220
Service Bulletin/Repair Instructions
JERKING OR SHUDDERING FROM THE DRIVELINE (XDRIVE TRANSFER CASE ATX13-X): There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages. CAUSE Unevenly worn or incorrect fitment tires are installed on the vehicle or the factory-filled transfer case oil does not meet BMW specifications.
B610520
Service Bulletin/Repair Instructions
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B611220
Service Bulletin/Repair Instructions
TRUNK LOCK SWITCH INSIDE THE GLOVE COMPARTMENT IS MISSING: The trunk lock switch ("hotel"/valet switch) is missing in the glove compartment. This switch decouples the trunklid from the central locking system so that the trunklid cannot be opened. Incorrectly built production vehicles.
B660920
Service Bulletin/Repair Instructions
SURROUND VIEW WRONG VEHICLE DISPLAYED AFTER PROGRAMMING: After programming the wrong vehicle model is displayed in the Central Information Display (CID) when the Surround View is activated.
B121619
Service Bulletin/Repair Instructions
ERRONEOUS ELECTRIC FAN FUNCTION FAULT STORED IN THE DME: The following faults may be erroneously stored in the Digital Motor Electronics (DME): Fault code: Control module: Fault code text: 1A2806 DME Electric fan function: limited operation 1A4007 DME Electric fan function: Operating mode implausible And: There is no customer-facing vehicle symptom(s) or related check control message displayed. A software error may cause these faults to be erroneously stored in the Digital Motor Electronics (DME).
B130320
Service Bulletin/Repair Instructions
DELIVERY STOP - REPLACE HIGH-PRESSURE PUMP: Due to an assembly error the flange bolts for the high-pressure pump did not have the proper tightening torque applied.
B510820
Service Bulletin/Repair Instructions
GROANING OR CRACKING NOISE WHEN OPENING OR CLOSING THE DOORS: A groaning or cracking sound is present when opening and/or closing any of the doors. Interference between the door panel and door.
B513016
Service Bulletin/Repair Instructions
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B610320
Service Bulletin/Repair Instructions
MIL MAY BE ILLUMINATED BY ERRONEOUS FAULT IN THE DME: The customer states that the malfunction indicator lamp (MIL) is illuminated. During diagnosis fault code 231507 "BDC RESET by watchdog" stored in the DME. CAUSE Software error in the Body Domain Control (BDC) unit.
B611420
Service Bulletin/Repair Instructions
DEACTIVATION OF THE INTERIOR MOVEMENT DETECTOR/TILT ALARM SENSOR IS NOT POSSIBLE: Customer complains that the interior movement detector and the tilt alarm sensor system cannot be deactivated by pressing the lock button on the remote control / BMW display key twice. The second button press on the radio remote control / BMW display key is not detected. Customer may have to press the button 3 times to deactivate the interior movement detector and tilt alarm sensor. CAUSE Software error in the control unit of the roof function center (FZD).
B650520
Service Bulletin/Repair Instructions
FAULT 930C1E IS FOUND IN THE ACSM: Vehicle comes into the workshop with the following illuminated: Check Engine Light DSC warning lamp Air bag warning lamps During diagnosis the following fault code is found stored in the ASCM (Advanced Crash Safety Module): 930C1E internal ECU error If the fault is cleared it returns immediately. The root cause is under investigation.
B650820
Service Bulletin/Repair Instructions
DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. This can occur when browsing/scrolling through lists in the audio menu switching radio stations or albums. Software in the Head Unit High (HU-H3).
B652214
Service Bulletin/Repair Instructions
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B660320
Service Bulletin/Repair Instructions
DIAGNOSTIC HINT: DRIVING ASSISTANCE SUPPORT REDUCED CHECK CONTROL MESSAGE DISP: Driving Assistance support reduced Check Control Message (CCM) is displayed sporadically. All or some of the system functions maybe inoperative.
B660817
Service Bulletin/Repair Instructions
REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 6) replaces SI B66 08 17 dated January 2020. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change.
B661418
Service Bulletin/Repair Instructions
CHECK CONTROL MESSAGE CROSSING TRAFFIC WARNING WHILEPARKING: The check control message (CCM) "Crossing traffic warning. It is possible to continue driving" can appear when parking. This can occur when the vehicle is parked too close to adjacent solid walls such as a single car garage or an underground parking space. The wall can be on either side of the vehicle regardless if the vehicle is pulled in forwards or backed in. If the customer switches the vehicle off and starts it again immediately the same CCM may occur again.
B720417
Service Bulletin/Repair Instructions
FALSE WARNINGS THAT THE FRONT PASSENGER SEAT IS OCCUPIED WITHOUT THE SEAT BELT BUCKLED: This Service Information Bulletin (Revision 10) replaces SI B72 04 17 dated September 2019. Acoustic and visual warnings indicate that the front passenger seat is occupied and the safety belt is not fastened when the seat is actually unoccupied. If the situation is currently present sit in the seat and move the seat to a slightly different position. The POL (Passenger Occupancy Light) light should now function correctly. In some cases the Air bag Warning Light was illuminated.
B840214
Service Bulletin/Repair Instructions
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B111219
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP IS ILLUMINATED WITH A CRANKSHAFT ADAPTION FAULT: When diagnosing an illuminated malfunction indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.
B120419
Service Bulletin/Repair Instructions
DME FAULT MEMORY ENTRY FOR THE CRANKSHAFT SENSOR: This Service Information Bulletin (Revision 1) replaces SI B12 04 19 dated February 2019. Technicians may notice this fault logged during a diagnostic session: Fault code: Control module: Fault Text: 160021 DME Crankshaft sensor: general loss of synchronism Environmental conditions are vehicle speed 0 (stationary) and engine speed less than 1500 rpm. There is no customer-facing symptom nor related check control message displayed. Phantom/pseudo fault due to unsuitable DME software. Background: After parking the vehicle and turning off the engine both DME control units go into sleep mode at different times. The DME of cylinder bank 2 ("secondary") goes into sleep mode first The DME of cylinder bank 1 ("primary") is still awake and can experience a reduction in signal voltage for the crankshaft sensor signal This signal change can mistakenly be evaluated as a skipped crankshaft sensor cog by the DME. If the engine is started while the primary DME is still awake this causes a brief loss of synchronization with the secondary DME. Fault 160021 is logged after three (3) consecutive engine starts with this momentary loss of synchronization. Note: Starting the engine after the primary DME has also gone into sleep mode will avoid the loss of synchronization.
B662017
Service Bulletin/Repair Instructions
DISPLAY KEY IS NON-FUNCTIONAL: This Service Information Bulletin (Revision 3) replaces SI B66 20 17 dated October 2019. The display key is non-functional. Display Key cannot be charged or switched on. An incorrect vehicle model appears on the key display. Possible defective display key battery or display key.
B110819
Service Bulletin/Repair Instructions
B57 DIESEL ENGINE - CHECK CONTROL MESSAGE OIL LEVEL TOO HIGH. Check Control Message (CCM) "Engine oil level too high" is displayed. Fuel dilution into the engine oil due to the diesel particulate filter (DPF) regeneration strategy.
B120319
Service Bulletin/Repair Instructions
ENGINE DOES NOT START BELOW FREEZING TEMPERATURES: Engine designation correction Parts availability Warranty. The engine will not start at temperatures below freezing. The starter does not turn and engage.
B511319
Service Bulletin/Repair Instructions
DOOR LATCHING COMPLAINTS IN COLD WEATHER: Below freezing ambient temperatures: One or more doors (front or rear) may not open when attempting to enter or After opening they may not correctly latch A leaking seal on the outer Bowden release cable may allow water to enter the cable sheathing and freeze.
B620919
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER REMAINS DARK AFTER STARTING THE VEHICLE: Instrument cluster remains dark after starting the vehicle. After a restart normal functionality is restored. Software error in the KOMBI (Instrument Cluster).
B621019
Service Bulletin/Repair Instructions
INCORRECT CONDITION BASED SERVICE DATA FOR BRAKE FLUID SERVICE. "Brake fluid service due since 12/2001" is displayed in the instrument cluster although the vehicle is only a maximum of 1 year old. Software error in the KOMBI (Instrument Cluster).
B340319
Service Bulletin/Repair Instructions
HUMMING RUMBLING NOISES AFTER OPENING THE DOOR: After waking up/unlocking and entering the vehicle a humming/rumbling noise may occur.
B651019
Service Bulletin/Repair Instructions
ENGINE SPEED DEPENDENT NOISE DURING AUDIO PLAYBACK: Integration level updated. There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit.
B652219
Service Bulletin/Repair Instructions
NO AUDIO IS AVAILABLE FOR APPROXIMATELY 30 SECONDS AFTER HEAD UNIT START UP: After programming vehicle no audio is available for approximately 30 seconds after head unit start-up. Fault code B7F490 "Control unit reset" is present in the RAM (Receiver Audio Module).
B611219
Service Bulletin/Repair Instructions
DELIVERY STOP: REPLACE THE GEAR SELECTOR SWITCH: The functional lighting and/or locator lighting on the Shifter selector lever (GWS) may flicker over time or intermittently not illuminate. The GEAR SELECTOR SWITCH may not have been produced to specifications.
B651419
Service Bulletin/Repair Instructions
HEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT: The CID screen may light up blue. When this occurs A battery reset is not successful in restoring head unit operation Software error in the Bootloader file (BTLD) of the head unit.
B662319
Service Bulletin/Repair Instructions
DRIVERS ASSISTANCE SYSTEM: CHECK CONTROL MESSAGE IS DISPLAYED. The Driver Assistance System limited warning message is displayed.
B651519
Service Bulletin/Repair Instructions
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
B123018
Service Bulletin/Repair Instructions
ERRONEOUS FAULT 1F2505 IS STORED IN THE DME This Service Information bulletin replaces SI B12 30 18 dated November 2018. This fault does not cause any drivability complaints or engine warning lamps.
B130519
Service Bulletin/Repair Instructions
DELIVERY STOP: CAMSHAFT SENSORS. On affected vehicles the camshaft sensors will be inspected and if necessary replaced.
B521119
Service Bulletin/Repair Instructions
CLICK CLACK NOISES IN BACKREST AREA OF FRONT SEAT: An alternating "click-clack" noise is heard from the backrest area of the front seat when an occupant sits in the seat or when the vehicle is cornering. Due to the elimination of the NED (Non-Electrical Diagnosis) test plan for seat noise from ISTA we are releasing this bulletin. Seat backrest frame is touching the seat cover.
B640519
Service Bulletin/Repair Instructions
INTEGRATED AUTOMATIC HEATING/ AIR CONDITIONING SYSTEM: VARIOUS COMPLAINTS CONCERNING CLIMATE CONTROL: The BMW 5 Series (G30) is equipped with an advanced and optimized integrated automatic heating and air conditioning system (IHKA).
B110119
Service Bulletin/Repair Instructions
ENGINE VIBRATIONS OR NOISE This Service Information bulletin replaces SI B11 01 19 dated February 2019.
B122119
Service Bulletin/Repair Instructions
HIGH ENGINE SPEED IMMEDIATELY AFTER STARTING. In rare circumstances after the engine is started with the Start-Stop button the engine speed may immediately increase to a high constant RPM (approximately 3000 rpm).
B180119
Service Bulletin/Repair Instructions
NITROGEN OXIDE SENSOR FAULTS. The Service Engine Soon (MIL) is illuminated and one or more of the following fault codes are stored in the DDE.
B320619
Service Bulletin/Repair Instructions
VARIOUS CHECK CONTROL MESSAGES FOR DRIVER ASSISTANCE SYSTEMS.
B110717
Service Bulletin/Repair Instructions
FAULT 118002 - MIXTURE TOO RICH SETS DURING WINTER WITH COLD AMBIENT TEMPERATURES. The Service Engine Soon (MIL) light is on with the following fault stored in the Digital Motor Electronics (DME). In the situation being described the fault is primarily stored during the cold winter months along with the use of winter fuel.
B122019
Service Bulletin/Repair Instructions
DELIVERY STOP: PROGRAM CONTROL UNITS (DME). A Delivery Stop has been issued (effective May 16 2019) on certain Model Year 2016-2020 BMW vehicles that have been produced between June 19 2015 and April 17 2019. A software error within the Digital Motor Electronics (DME) may cause a miscalculation of an onboard diagnostic (OBD) function. All vehicles will need a software update (no parts required).
B340819
Service Bulletin/Repair Instructions
VARIOUS CHECK CONTROL MESSAGES FOR DRIVER ASSISTANCE SYSTEMS. The following messages are displayed in the Check Control (CC) display: Continued driving possible. Driving stabilization. Driving stabilization restricted driving stabilization. Drive with caution to the nearest authorized BMW Service workshop and/or Collision warning/you can continue driving. Collision warning fully or partially failed. No warning is given if the distance from the vehicle in front is too short.
B610619
Service Bulletin/Repair Instructions
HIGH VOLTAGE DIAGNOSTIC SPECIALIST TRAINING AND EQUIPMENT STRATEGY. INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians.
B840311
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT ACTIVATION VIA DCSNET FOR BMW ASSIST.
B170118
Service Bulletin/Repair Instructions
HEATER HOSE IS CONTACTING THE STEERING SHAFT This Service Information bulletin replaces SI B17 01 18 dated April 2018.
B511419
Service Bulletin/Repair Instructions
KIDNEY GRILL(S) LOOSE. One or both kidney grills may be loose.
B620518
Service Bulletin/Repair Instructions
HEADS UP DISPLAY SPORADICALLY INOPERATIVE. Fault memory entry "B7F6E4 HUD: Fault in display backlighting "is stored in the instrument cluster. Intermittently the Head-Up Display (HUD) may deactivate.
B170618
Service Bulletin/Repair Instructions
ACTIVE AIR FLAP FAULT DIAGNOSIS HINTS. A check engine light or check control message is present.
B611918
Service Bulletin/Repair Instructions
STANDARD OCCASIONAL USE CABLE CHARGING COMPLAINT TROUBLESHOOTING This Service Information bulletin supersedes SI B61 19 18 dated November 2018.
B661119
Service Bulletin/Repair Instructions
NIGHT VISION 3: INTERNAL SOFTWARE ERROR FAULT. During vehicle diagnosis of an unrelated issue the following erroneous fault may be stored in the Night Vision 3 control unit.
B111516
Service Bulletin/Repair Instructions
B58 ENGINE: OIL LEAK FROM TURBOCHARGER. Engine oil (1) can be seen leaking from the bottom of the turbocharger near the band clamp (2). The turbocharger band clamp is loose.
B120219
Service Bulletin/Repair Instructions
SERVICE ACTION: CBS DATA MAY NOT BE DISPLAYED. Incorrect activation of the Condition Based Service (CBS) data may cause the engine oil information to not be displayed. A software error in the Digital Motor Electronics (DME).
B240219
Service Bulletin/Repair Instructions
TRANSMISSION SHIFTING FAULTS AT COLD TEMPERATURES.
B540718
Service Bulletin/Repair Instructions
PANORAMIC SUNROOF DOES NOT OPEN OR CLOSE. The panoramic sunroof will not open or close. The sunroof may only tilt with no other functions available. There are no faults stored for the panoramic sunroof. A software error in the Roof Function Center (FZD).
B641418
Service Bulletin/Repair Instructions
NO COOLING INTERMITTENTLY FROM VENTS. After a long journey (more than 30 minutes).
B651118
Service Bulletin/Repair Instructions
FM RADIO STATIC HEARD BETWEEN 88 TO 97 MHZ.
B661918
Service Bulletin/Repair Instructions
FAULT CODE 804417 CAUSED BY THE REMOTE KEY. When a short test is performed as part of a workshop visit for an unrelated situation.
B160818
Service Bulletin/Repair Instructions
The fuel delivery unit (in-tank fuel pump) may be incorrect part installed for the Model/Market.
B641218
Service Bulletin/Repair Instructions
HEATING IN EDRIVE IS NOT AVAILABLE. No heater output in eDrive mode.
B111918
Service Bulletin/Repair Instructions
A Delivery Stop has been issued (effective November 16, 2018) on Model Year 2019 BMW 5 Series, 7 Series and X5 SAV vehicles that have been produced between June 29, 2018 ? September 10, 2018. The issue involves the oil-to-water heat exchanger which can start to leak. Approximately 285 vehicles are affected by this delivery stop.
B161018
Service Bulletin/Repair Instructions
DIESEL FAULTS FOR METERING QUANTITY (SCR03). The Malfunction Indicator Lamp (MIL) is illuminated and the following faults are stored in the Selective Catalyst Reduction (SCR03) Module * 805291 - Metering quantity deviation, metered quantity according to delivery volumes is too high. * 8052E3 - Metering quantity deviation, metered quantity too high, sum error. * 8052E5 - Metering interruption to diagnose a metering quantity deviation (metered quantity too high). A software calibration error in the SCR03 module.
B520518
Service Bulletin/Repair Instructions
SEAT MEMORY SWITCH SPORADICALLY NOT FUNCTIONING. Selecting one of the saved seat positions (via the memory seat position switch on the door panel), fails to work. A saved seat position cannot be retrieved. The memory function works again after a terminal change or backrest width adjustment. Note: Manual seat adjustment using the button for forward/back seat adjustment still works. Software error in the seat module.
B660218
Service Bulletin/Repair Instructions
RADIO REMOTE SPORADICALLY INOPERATIVE. INFORMATION All required parts can be found in the Electronic Parts Catalog.
B661618
Service Bulletin/Repair Instructions
COMFORT ACCESS AND PASSIVE GO DO NOT WORK AFTER REPLACING A REMOTE KEY. Note: This situation only affects the listed vehicles with a factory I-level lower than 18-03-XXX. After teaching in a new replacement radio remote key (aka radio-operated key), Comfort Access keyless entry and Passive Go (aka Convenience Starting) are no longer possible. However, it is possible to start the engine by holding the new key to the ring antenna at the right side of the steering column. CAUSE Software error in the remote key, and/or the Display Key where applicable.
B111318
Service Bulletin/Repair Instructions
SERVICE ACTION: N63R ENGINE - CHECK AND REPLACE OIL FEED LINES AND THE CHARGE AIR COOLERS. This bulletin describes the procedures to inspect and if necessary replace the following components: * Turbo charger oil feed lines (leaking) * Charge air coolers (corrosion)
B111418
Service Bulletin/Repair Instructions
SERVICE ACTION: N63R ENGINE - CHECK AND REPLACE OIL FEED LINES AND THE MAP THERMOSTAT ELECTRICAL CONNECTOR. This bulletin describes the procedures to inspect and if necessary replace the following components: * Turbo charger oil feed lines (leaking) * Map thermostat and electrical harness (corrosion) Also, make sure that Service Bulletin B12 24 18 Service Action: Program Control Units, is completed when performing this Service Action.
B120718
Service Bulletin/Repair Instructions
DME FC 1C0102 IS STORED WITH NO OTHER RELATED FAULTS. The following fault has been stored in the Digital Motor electronics (DME) fault memory with no other engine oil pressure faults stored: ??1C0102 - oil pressure control, plausibility, static: Pressure too low This fault will not cause a customer complaint or a Check Control Message (CCM). The fault is typically identified during unrelated diagnostics. Software error in the Digital Motor Electronics (DME) may cause the fault code to be erroneously stored. Only Integration level 17-11-5xx and higher are affected.
B120918
Service Bulletin/Repair Instructions
NOISE FROM ENGINE WHEN STARTING. Noise when starting the engine. Engine making a rattling/grinding noise near the 12 volt starter motor. The following fault has been stored in the DME fault memory: * 21A511 - Start system, pinion starter motor: Timeout The following faults are also possible: * 21A504 - EGS, separation clutch: jammed open * 21A50A - Start system, pinion starter: Timeout successively occurred multiple times * 21A510 - Start system, EME: Timeout Consequential damage to flywheel (Torsional vibration damper) and automatic transmission may have also occurred. The starter motor is broken. It may be indicated by:
B122716
Service Bulletin/Repair Instructions
DIAGNOSING NON FUNCTIONING eDRIVE. * Vehicle will not go into "eDrive" * No pertinent electric drivetrain fault codes to assist with diagnosis * "eDrive" may be greyed-out in the Central Information Display (CID) and is not selectable * MSA deactivation * 12 volt battery failure * Intelligent Battery Sensor (IBS) failure.
B170418
Service Bulletin/Repair Instructions
DELIVERY STOP. LOW TEMPERATURE COOLANT SYSTEM.A Delivery Stop has been issued (effective October 16, 2018) on Model Year 2019 BMW 5 and 7 Series vehicles that have been produced from September 13-14, 2018. There is a possibility that the affected vehicles do not have the correct amount of coolant in the low-temperature coolant system. Approximately 3 vehicles are affected by this delivery stop that have already been delivered to dealers. Affected vehicles show the campaign as ?Open? when checked either in Warranty Vehicle Inquiry, AIR or ISPA Next and identified with the description: STOP013433 B170418 Delivery Stop: Low Temperature Coolant System. The bulletin will be updated with more information when it becomes available.
B613017
Service Bulletin/Repair Instructions
RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B111117
Service Bulletin/Repair Instructions
?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B270118
Service Bulletin/Repair Instructions
?DYNAMIC STABILTY CONTROL WARNING ON WITH LIMITED POWER STEERING ASSIST This Service Information bulletin replaces SI B34 09 16 dated January 2017 What's New: ? This SIB is a complete revision of B34 09 16. Steering feels heavy (limited power assist) The Dynamic Stability Control (DSC) light and Service Engine Soon light may be on. The following message may be displayed in the Check Control (CC): * CCM 350 "It is possible to continue to drive. All-wheel drive system." * Other CC messages may be stored related to: Restraint system / lane change warning / distance information / pedestrian protection. One or both of the following faults are stored in the DSC: * D36500 - Message fault (xDrive actuator information, ID: XDRV_ACT_INFO) - Timeout * D356E4 - Message fault (status of distribution of the longitudinal torque on the front axle rear axle, ID: ST_REPAT_XTRQ_FTAX_BAX) - Timeout The following faults can also be stored in the DDE or DME: * DDE: CD95E0 - Message (ST_REPAT_XTRQ_FTAX_BAX, 19.3.4,FX), Timeout: Message (status of distribution of longitudinal torque of front axle rear axle) from longitudinal torque distribution failed * DME: CDA056 - FlexRay, message (status of distribution of longitudinal torque of front axle rear axle / xDrive actuator information, 19.3.4): missing Internal fault in the transfer case control unit (Longitudinal Torque Module - LMV).
B661917
Service Bulletin/Repair Instructions
?SERVICE ACTION: CHECK AND REPLACE LANE CHANGE WARNING SENSOR. The Lane Change Warning sensor may have been produced with faulty components. This may lead to a failure of the Lane Change Warning system (SWW). Lane Change Warning sensor hardware defect.
B840616
Service Bulletin/Repair Instructions
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B120418
Service Bulletin/Repair Instructions
BUZZING NOISE FROM VALVETRONIC MOTOR BEFORE OR AFTER ENGINE OPERATION: Buzzing noise may be heard from the Valvetronic motor when the vehicle is unlocked, before the engine is started, or after the engine is turned off.
B620618
Service Bulletin/Repair Instructions
FUEL GAUGE INCORRECTLY DISPLAYING LOW FUEL LEVEL AFTER VEHICLE IS REFUELED: Occasionally, on restart after refueling, the fuel gauge will display the fuel level as low (minimum) and the range display will be at an implausible (maximum) value.
B660717
Service Bulletin/Repair Instructions
DEACTIVATION OF CONTACTLESS TAILGATE OPENING AND CLOSING: Customer desires to have contactless tailgate opening and closing (Smart Opener) deactivated.
B660818
Service Bulletin/Repair Instructions
ERRATIC PARK DISTANCE CONTROL SYSTEM BEHAVIOR: False detections occur when the wheels are turned (left or right) to a full end stop steering position.
B840918
Service Bulletin/Repair Instructions
PHONE CONTACTS: HEADUNIT BASIC 2 SORTING ORDER: Improper sorting of phone contacts, in the on-board computer or in the Central Information Display (CID), upon connecting to the vehicle:
B651316
Service Bulletin/Repair Instructions
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.: If either the head unit (NBT-EVO or ENTRY-NAV-EVO) or the Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit to enter a locked mode once it recognizes a different VIN.
B661318
Service Bulletin/Repair Instructions
SERVICE ACTION: REPLACE KAFAS CAMERA (CAMERAASSISTED DRIVERS ASSISTANCE SYSTEM): The KAFAS camera features are inoperative, and this does not trigger any warnings or check control messages.
B651117
Service Bulletin/Repair Instructions
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START: Navigation system will not start at all or the: ÒNavigation system startsÓ message is permanently displayed; or
B840818
Service Bulletin/Repair Instructions
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:
B340318
Service Bulletin/Repair Instructions
ELECTROMECHANICAL HOLDING BRAKE (EMF) ERROR
B612217
Service Bulletin/Repair Instructions
DIAGNOSTIC COMMUNICATION WITH FLEXRAY CONTROL MODULES NOT POSSIBLE: There are no customer complaints associated with this issue.
B621215
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
B840718
Service Bulletin/Repair Instructions
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition.
B840618
Service Bulletin/Repair Instructions
CONNECTEDDRIVE-REMOTE SERVICES DO NOT FUNCTION: Remote Services (such as locking and unlocking the car, vehicle location by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has been sitting for extended amount of time (In excess of 20 hours).
B120618
Service Bulletin/Repair Instructions
DME FAULT CODE CDC203: Various control units contain faults indicating missing messages from the battery management electronics
B130119
Service Bulletin/Repair Instructions
PROLONGED ENGINE CRANK WHILE STARTING (B57O). 1. The engine can sporadically crank for a prolonged period during a cold or hot start 2. The malfunction indicator lamp (MIL) may be illuminated. 3. Any of the following fault memory entries may be stored in the DDE 2E0600; 26CF00; 259800; 259E00.
B160118
Service Bulletin/Repair Instructions
REMOVING FUEL FEED LINE FOR PARKED CAR HEATING FROM REPLACEMENT FUEL PUMP: Modify the universal replacement fuel pump assembly to allow it to be correctly installed in a US market vehicle.
B160218
Service Bulletin/Repair Instructions
SERVICE ACTION: REPLACE THE TEMPERATURE SENSOR FOR THE TANK LEAK DIAGNOSIS MODULE (NVLD): The Service Engine Soon light is illuminated.
B612717
Service Bulletin/Repair Instructions
REPLACE BATTERY CHECK CONTROL MESSAGE: In-stock, new vehicle instrument cluster displays the red CCM ÒReplace BatteryÓ (ID # 460).
B621717
Service Bulletin/Repair Instructions
ERRONEOUS HEAD-UP DISPLAY FAULT IN INSTRUMENT CLUSTER: B7F6E3 - HUD: Fault in the communication (HUD not answering) in instrument cluster fault.
B621817
Service Bulletin/Repair Instructions
FUEL GAUGE ERRONEOUS DISPLAY: Vehicle runs out of fuel but the instrument cluster still displays fuel remaining in the tank.
B640118
Service Bulletin/Repair Instructions
TEMPERATURE REGULATION OF AUTOMATIC CLIMATE CONTROL SYSTEM IS NOT ACCEPTABLE: Air distribution and/or temperature regulation variation exceeds design parameters.
B640119
Service Bulletin/Repair Instructions
DEACTIVATION OF THE AUTOMATIC AIR RECIRULATION. Customer request for deactivation of the automatic air recirculation function.
B660418
Service Bulletin/Repair Instructions
DURING PARKING MANEUVERING ASSISTANT OPERATION, DRIVER GEAR INPUT IS IGNORED: Sporadically, during a Parking Maneuvering Assistant or Parking Assistant operation the gear change requested (R to D or D to R) by the driver is ignored.
B660718
Service Bulletin/Repair Instructions
GREEN BARS DISPLAYED IN CENTRAL INFORMATION DISPLAY WHEN CAMERA ACTIVE: Wide green bar across bottom and up right side of Central Information Display (CID) when reverse gear is selected and the Surround View camera is active.
B661317
Service Bulletin/Repair Instructions
SURROUND VIEW CAMERA DISPLAYS INCORRECT VEHICLE MODEL: After programming the vehicle, the incorrect vehicle model is displayed in the CID (Central Information Display) when surround view camera function is active.
B841117
Service Bulletin/Repair Instructions
BMW APPS RANDOMLY STARTS PLAYING ON ITS OWN: While listening to FM, or AM, or Satellite Radio (SDARs), the audio source randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.
B120318
Service Bulletin/Repair Instructions
NO AUDIBLE DIFFERENCE IN EXHAUST WITH "M PERFORMANCE POWER AND SOUND KIT
B611316
Service Bulletin/Repair Instructions
KLE CHARGING FAULT 21E6E9: During the ISTA short test diagnosis, fault code 21E6E9 Ð ÒCharging electronics: Charging mode interruptedÓ is found stored in the KLE (Convenience Charging Electronics) module.
B650318
Service Bulletin/Repair Instructions
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback.
B662417
Service Bulletin/Repair Instructions
REMOTE CONTROL PARKING SPORADICALLY DEACTIVATES: During operation of (when using) the Remote Control Parking (RCP) function, it can sporadically, autonomously shut down.
B840314
Service Bulletin/Repair Instructions
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B122717
Service Bulletin/Repair Instructions
ERRONEOUS INTERNAL FAULT 10501D IS STORED IN THE DME: The following fault is erroneously store in the Digital Motor Electronics (DME).
B123017
Service Bulletin/Repair Instructions
SERVICE ACTION: PROGRAM CONTROL UNITS (EME): Due to the EME software error, OBD diagnostics may not detect emission relevant fault codes stored in the IHKA (heating & A/C) control module
B513417
Service Bulletin/Repair Instructions
WINDSHIELD WIPER HITTING A-PILLAR: Windshield wiper is hitting the A-pillar at the upper end of its travel.
B621917
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER REMAINS DARK AFTER STARTING THE VEHICLE: Upon starting the vehicle (terminal 15 switched on), the instrument cluster does not function (stays dark, no needle response, no bus communication).
B640917
Service Bulletin/Repair Instructions
WARM AIR DISCHARGE FROM FOOTWELL VENT WITHOUT REQUEST: While driving, and without request, the footwell vent discharges warm air.
B661717
Service Bulletin/Repair Instructions
MISSING DISPLAY OF SURROUND VIEW CAMERA: Central Information Display (CID) sporadically does not display Surround View Camera image.
B662517
Service Bulletin/Repair Instructions
DISPLAY KEY NOT DETECTED IN VEHICLE: After display key remains motionless in the vehicle (or in the trunk) for more than two minutes, it is no longer detected.
B240317
Service Bulletin/Repair Instructions
8HP50 TRANSMISSIONS GEAR SHIFTS FROM REVERSE TO NEUTRAL: After a cold start, when the transmission gear selector is placed in R and driving resumes, intermittently transmission may shift to Neutral
B160417
Service Bulletin/Repair Instructions
DME FAULT CODE 194006 TANK LEAKAGE DETECTION MODULE, SOLENOID VALVE: JAMMED OPEN. Malfunction Indicator Lamp (MIL) is illuminated. The following fault code is stored in the DME: 194006 Tank leakage detection module, solenoid valve: jammed open is presentThe following fault code may also be stored with FC 194006: 190302 Fuel tank ventilation system micro-leak: Leakage larger than 0.5 mm. Vacuum leak in fuel tank ventilation system or an internal failure (pressure switch) of the NVLD (Natural Vacuum Leak Detection).
B513017
Service Bulletin/Repair Instructions
A-PILLAR WIND NOISE. At vehicle speeds above 60 mph, wind noise is heard from the vicinity of the A-pillar. Excessive gap between the roof trim strip and the A-pillar.
B620717
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER REMAINS DARK & DOES NOT START UP This Service Information bulletin replaces SI B62 07 17 dated May 2017 What's New: Changed affected production dates & options Procedure wording Changed I-level of software. G12 (7 Series) G30 (5 Series Sedan) Vehicles produced up to 3/1/2017. The instrument cluster (KOMBI) display does not appear when the vehicle is started. Software in the instrument cluster incorrectly initiates the safety mode causing the cluster display to remain dark.
B661117
Service Bulletin/Repair Instructions
ACC (ACTIVE CRUISE CONTROL): CANNOT DELETE FAULT CODE 022126. ACC fault code 022126 does not delete from ACC control unit fault code memory. May occur in combination with under-voltage fault codes: * BDC 0x80402F - Battery deeply discharged * BE6: 0x801405 - Under-voltage detected Insufficient control unit software.
B170517
Service Bulletin/Repair Instructions
SERVICE ACTION: REPLACE THE MOUNT FOR THE TRANSMISSION OIL COOLER THERMOSTAT. There may be a rattling noise coming from the engine area at the transmission oil cooler thermostat or (on xDrive models only) the transmission oil cooler lines coming into contact with the left front output shaft. The bracket that holds the transmission oil cooler thermostat to the left front frame rail may be defective
B410317
Service Bulletin/Repair Instructions
SERVICE ACTION: WATER INGRESS BENEATH LUGGAGE COMPARTMENT. Possible water leakage into luggage compartment through PVC weld on floor. Accumulation of water in luggage compartment may not be noticed due to drain location in the vicinity. Manufacturing process change moved PVC weld on underside of vehicle, beneath luggage compartment.
B613417
Service Bulletin/Repair Instructions
SERVICE ACTION: PROGRAM CONTROL UNITS (GWS). After the engine start-up, gear (Drive or Reverse) cannot be selected. Message "No drive position change possible" is displayed in the CC display. Gear can be selected only after vehicle goes through the sleep cycle. Unfavorable GWS gear shifter software
B621017
Service Bulletin/Repair Instructions
ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, BMW Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error
B660617
Service Bulletin/Repair Instructions
THE SMART OPENER TAILGATE IS ACTIVATED TOO EASILY. The touchless tailgate opening/closing activation is: * Too sensitive * Randomly initiated Software error in the tailgate function module
B3106170621
Service Bulletin/Repair Instructions
Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC73 must appear in the text of your TEC claim.
B612817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F04B. One or several of the following check control messages (CCM) may be displayed: "Engine fault! Power loss" (CCM-ID: 29) "Powertrain malfunction!" (CCM-ID: 633) "Hybrid system malfunctioning!" (CCM-ID: 585) Note: The fault code 21F04B stated below may also be entered without any of the above mentioned CC messages being displayed A timing problem between the SME and the cell supervision circuit (CSC).
B620817
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER CANNOT BE PROGRAMMED. When programming the vehicle the instrument cluster fails to program. Missing software for instrument cluster.
SIM010917
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
SIM120517
Service Bulletin/Repair Instructions
Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks for
SISIB011317
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, LLC
B170217
Service Bulletin/Repair Instructions
CHECK CONTROL (CC) MESSAGE:"COOLANT LEVEL TOO LOW!" IS DISPLAYED. CC message: "Coolant level too low!" appears in the display. The cooling system wasn't efficiently bled during the factory fill.
B512517
Service Bulletin/Repair Instructions
SERVICE ACTION: REMOVE XDRIVE NAME PLATE FROM TRUNK LID. The xDrive name plate on the left side of the trunk was incorrectly installed at the factory and needs to be removed. The xDrive name plate on the left side of the trunk was incorrectly installed at the factory and needs to be removed.
B612117
Service Bulletin/Repair Instructions
HAZARD WARNING SWITCH FLICKERS AFTER ENGINE START. Hazard warning switch flickers after engine start. Faulty communication between hazard warning switch and Body Domain Controller (BDC).
B660417
Service Bulletin/Repair Instructions
LOCKING FUNCTION INOPERATIVE FROM THE HANDLE, ON VEHICLES WITH COMFORT ACCESS. Touching a door handle does not activate locking/closing function after exit from vehicle via Comfort Access. All door handles are affected when vehicle is wet or after rain. Keyless entry is possible via the remote control key Moisture penetration between locking sensor and handle support.
B112216
Service Bulletin/Repair Instructions
?"ENGINE OIL PRESSURE" ON LOW MILEAGE CARS. Check Control Message (CCM-212) states: "Engine Oil Pressure. Stop Carefully" The following codes may be stored in the DME fault memory" 1C2002 - Engine oil pump, pressure too low 1FB801 - CCM (ID212) - Oil pressure Also, the vehicle's mileage is very low (below 60 miles), the fault frequency shows only "one" occurrence; faults are not currently present and cannot be reproduced. CAUSE Unfavorable DME software application."
B340317
Service Bulletin/Repair Instructions
DYNAMIC STABILITY CONTROL FAILURE. Instrument cluster indicates Dynamic Stability Control (DSC) failure. You cannot establish communication with the DSC control unit. Associated control units (DME, ACSM) register DSC-related communication time-outs. After battery reset, DSC operates normally and has no faults registered. Software in the DSC control module.
B340417
Service Bulletin/Repair Instructions
?DSC WARNING LAMP ILLUMINATED AFTER TRANSPORT MODE DEACTIVATION. After vehicle start-up from transport mode, the DSC warning lamp flashes. CC message driving stabilization restricted" is displayed in the CID. The following faults are entered in the fault memory: 0x482394 EPS control unit: Initialization fault steering angle, loss of multi-turn value. 0x48078B DSC control unit: Initialization fault EPS, adjustment required. The order of transport mode deactivation and steering angle sensor initialization reversed. While in transport mode, the steering angle sensor loses calibration on every terminal change. During the QCI service, transport mode deactivation is supposed to occur prior to steering angle sensor initialization. When this is reversed, calibration is lost."
B341017
Service Bulletin/Repair Instructions
LOW-SPEED BRAKE SQUEAL: Vehicle brakes produce a squealing noise when applied at low speed.
B511317
Service Bulletin/Repair Instructions
WIND NOISE FROM REAR SIDE WINDOW. At highway speed, wind noise is heard from either rear side window. CAUSE Gap between the window guide and the window guide bar. Replace the window guide after verification of cause.
B511517
Service Bulletin/Repair Instructions
HOOD DOES NOT RELEASE PROPERLY. Hood lever is pulled twice but the hood only achieves the pre-latch position on one side while the other is still latched. Downward pressure on the side of the hood that remains latched will release it to the pre-latch position. After pre-latch position is achieved on both sides, the hood unlatch lever must be pulled again to achieve unlatched position. Hood latch mechanical release is not operating properly. Neither hood latch can be released to the fully open position until both have achieved the pre-latch position.
B611817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F02A. Upon starting the vehicle, the following CC message is displayed to the customer: Powertrain malfunction!" (CCM-ID: 633) In addition, one or several of the following CC message(s) may be displayed: "Charging not possible" (CCM-ID: 804), "Hybrid system malfunctioning!" (CCM-ID: 585), "Drive. No restart" (CCM-ID: 586) or "Engine fault! Power loss" (CCM-ID: 29). Possible hardware defect of the safety box."
B620617
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER RESETS. Instrument cluster sporadically flickers and/or fails. Instrument cluster performs spontaneous reset. Instrument cluster software.
B410117
Service Bulletin/Repair Instructions
?SERVICE ACTION: PVC WELD SEAM BENEATH LUGGAGE COMPARTMENT . Possible water leakage into luggage compartment through PVC weld on floor. Improperly applied PVC weld on underside of vehicle, beneath luggage compartment.
B511017
Service Bulletin/Repair Instructions
?LOOSE, NOISY, BMW EMBLEM ON TAILGATE . BMW emblem on tailgate wobbles and makes crackling noise when touched. Incorrect initial installation.
B520816
Service Bulletin/Repair Instructions
FRONT SEAT ADJUSTMENT, WRONG DISPLAY/ERROR RECOGNITION (FAULTY DETECTION) IN CID What is new ? G30 has been added. ? "Correction" has changed from programming solution to replace seat switch. ? Procedure" has been changed to replace the seat switch instead of programming. ? ""Parts Information"" has been added for the seat switch. ? Warranty Labor Ops have changed to reflect the updated procedure to replace the seat switch. This Service Information bulletin supersedes SI B52 08 16 dated October 2016. . The seat adjustment is erroneously displayed in the Central Information Display (CID) even though no adjustment was made at the seat switch. Front seat adjustment switch"
B540117
Service Bulletin/Repair Instructions
?GLASS ROOF NOT CLOSING . Glass roof will not close. At least one of the following fault codes is stored: 30215: Slide/tilt sunroof: invalid characteristic curve, no standardization exists 30295: Electric sliding headliner: invalid characteristic curve, no standardization exists 302A0: Electric sliding headliner: System not standardized 30220: Slide/tilt sunroof: System not standardized Roof function center software.
B610917
Service Bulletin/Repair Instructions
?FAULT CODE CD0600 IN CENTRAL GATEWAY MODULE . Discovered during vehicle diagnosis, Fault Code CD0600 "Ethernet unexpected linkdown" is recorded in Central Gateway Module (ZGW). No malfunction perceptible to the customer. Erroneous fault memory entry.
B630217
Service Bulletin/Repair Instructions
?CCM DISPLAYED FOR TURN SIGNAL OR REVERSE LIGHTS G30 (5 Series Sedan) Produced to March 01, 2017 SITUATION One of the following Check Control Messages (CCM) is displayed: "Turn indicator at the front left/right faulty" "Reversing light faulty" Turn signal flash frequency is double the normal frequency. OR Reverse bulb is illuminated for very short time. One or more of the following fault codes is stored in the Body Domain Controller (BDC): 0x80419C or 0x80419D: Front turn indicator 0x80486A or 0x80486B: Reversing light CAUSE BDC software CORRECTION Reprogram and encode the vehicle.
B650417
Service Bulletin/Repair Instructions
?CROSS TRAFFIC WARNING MISSING FROM INTEGRATED OWNERS MANUAL . The crossing traffic warning (right of way warning) section is missing from the integral owner's manual (IBA). The picture below shows the missing text. Software error in the Head unit IBA file
B650617
Service Bulletin/Repair Instructions
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B661016
Service Bulletin/Repair Instructions
?GARAGE DOOR OPENER CANNOT BE PROGRAMMED Whats new: ? "Model": G30 (5 Series) added . The vehicle's rear view mirror integrated universal remote control is incompatible with some garage door (or fence) opener devices installed at the driver's residence and/or business. If the garage door opener was manufactured before 1993, it will not be compatible with any HomeLink device. Installing the compatibility bridge will NOT link these units. This is due to several incompatible frequency's used before 1993.
B340116
Service Bulletin/Repair Instructions
?DYNAMIC STABILITY CONTROL (DSC) WARNING LAMP, LIGHTS UP This Service Information bulletin supersedes SI 34 01 16 dated October 2016 . Various "DSC warning lamps lights up in the instrument cluster, including the display: "Suspension control system failed". DSC control unit.
B510317
Service Bulletin/Repair Instructions
?B-PILLAR WIND NOISE . While driving at highway speeds, wind noise can be heard from the rear of either or both front doors. Sealing lip of inner window cavity seal is bent as shown on left below. Seal placement should be as shown on right, parallel to green line.
B610517
Service Bulletin/Repair Instructions
?WINDOW WASHER FLOW INTERRUPTION . Front windshield washers spray poorly or not at all. CAUSE Partially or completely pinched supply tube caused by misplaced tube holder on hood hinge. Reposition and secure tube holder on the gas pressure spring.
B000117
Service Bulletin/Repair Instructions
?SI B00 01 17 General Maintenance and Hints for G30 QUALITY FEEDBACK