B010122
Service Bulletin/Repair Instructions
N63TU1 CLASS ACTION SETTLEMENT SVC CAMPAIGN: OIL CONSUMPTION DIAGNOSIS/REPAIR
Vehicle report
2017 BMW 550I
Service bulletins
142 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B630418
Service Bulletin/Repair Instructions
One or more of the LED daytime running lights are dim or discolored.
B120721
Service Bulletin/Repair Instructions
Check Control message (CCM) indicates: (ID 213): Stop, exercising due care. Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt betweenCombustion engine and starter generator torn And/or one or more of the following other issues are also occurring: Noise in the area of the belt drive. Odor from the engine compartment. Smoke formation in the area of the belt drive. Drive belt damaged or prematurely worn. Torn drive belt.
B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B360121
Service Bulletin/Repair Instructions
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned. This can be felt (jerking)/ heard via an acoustic acknowledgement (clunk) as seen at the 11 second mark of the video. See attached video V36 01 21.
B610524
Service Bulletin/Repair Instructions
The Central Information Display goes black intermittently due to resets of the Head Unit (HU-H3). FaultB7F8F9 ÃÂâÃÂÃÂÃÂàÃÂâÃÂÃÂÃÂÃÂHU-H: ResetÃÂâÃÂÃÂÃÂàwill be stored in the HU-H3.
B320223
Service Bulletin/Repair Instructions
SITUATION Unusual noises occur only when operating the steering column in the axial direction. 1. A one-time thump sound at the start of movement Shortly after the steering column starts moving, retracting, or extending, a one-time thump noise is heard. See attached video V32 03 23 2. Humming noise while steering column extends in the axial direction. The sound is only heard when the steering column is extended, not when the steering column is retracted. When the steering column starts to move in the extended direction, the humming noise can be heard. See attached video V32 04 23
B160623
Service Bulletin/Repair Instructions
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
B653423
Service Bulletin/Repair Instructions
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
B010919
Service Bulletin/Repair Instructions
DIESEL FUEL INJECTORS: LTD WTY EXTENSION TO 10 YEARS/120,000 MILES
B011423
Service Bulletin/Repair Instructions
PRESSURE CONTROL VALVE (PCV) EXTENDED LTD WTY 15 YEARS/150,000 MILES
B650414
Service Bulletin/Repair Instructions
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
SIB650922
Service Bulletin/Repair Instructions
The sound output intermittently drops out entirely. This can be reproduced with all audio sources as well as telephone and voice output.
SIB651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B111614
Service Bulletin/Repair Instructions
This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
B010222
Service Bulletin/Repair Instructions
BMW of North America, LLC (BMW NA) has entered into a nationwide settlement with the plaintiffs in the following class action: Isley, et al. v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.
B170121
Service Bulletin/Repair Instructions
The quick disconnect coupling on the cylinder head coolant vent line could break at the cylinder head. This would lead to loss of coolant from the engine.
B651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B012118
Service Bulletin/Repair Instructions
While engine oil consumption may create a customer inconvenience, in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle
B840121
Service Bulletin/Repair Instructions
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
B651320
Service Bulletin/Repair Instructions
COLLECTION OF DRIVER'S AND PASSENGER'S SIDE AIR BAGS: BMW intends to perform evaluations and analyses on these side air bags.
B130720
Service Bulletin/Repair Instructions
INCORRECT TORQUE SPECIFICATION FOR THE HIGH-PRESSURE PUMP IN ISTA: The current version of ISTA states the incorrect tightening torque for the High-Pressure pump M6 mounting bolts to the cylinder head cover. The correct tightening torque is only 12 Nm for the M6 bolts.
B310112
Service Bulletin/Repair Instructions
CRACKING NOISES FROM THE FRONTAXLE AREA WHILE TURNING THE WHEELS, WHEN STATION: Cracking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.
B010319
Service Bulletin/Repair Instructions
N63T REAR MONITORING OXYGEN SENSORS - LTD WTY EXTENSION TO 10 YEARS/120,000 MILES: Component-Specific Limited Warranty Extension For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Rear Monitoring Oxygen (O2) Sensors (one shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date This component-specific limited warranty extension applies to defects in materials or workmanship.
B012218
Service Bulletin/Repair Instructions
N63 CLASS ACTION SETTLEMENT - BATTERY SERVICE BENEFIT - RETROFITS/ REPLACEMENTS: This Service Information bulletin applies to: Class vehicles in operation on the road (Applicable N63 engine model vehicles); by Class members (Class Vehicle owners on the date this settlement became effective), And it provides diagnostic/repairs instructions, as well as, Warranty Information for performed remedies.
B340517
Service Bulletin/Repair Instructions
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B650709
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B513016
Service Bulletin/Repair Instructions
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B652214
Service Bulletin/Repair Instructions
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B840214
Service Bulletin/Repair Instructions
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B010518
Service Bulletin/Repair Instructions
LIMITED WARRANTY EXTENSIONTO 10 YEARS/120000 MILES: This Service Information Bulletin replaces SI B01 05 18 dated July 2019. Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.
B012918
Service Bulletin/Repair Instructions
N63 ENGINE VEHICLES: CLASS ACTION SETTLEMENT FOR ENGINE OILCONSUMPTION/BATTER. What's New: The short-term extension window of one (1) year/12,000 miles from date of the settlement has expired.
B651519
Service Bulletin/Repair Instructions
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
B111216
Service Bulletin/Repair Instructions
The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM (fluoroelastomer) rubber material. The FPM rubber material is engine heat resistant. Or The plastic corrugated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
B122319
Service Bulletin/Repair Instructions
DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL. In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
B160419
Service Bulletin/Repair Instructions
NEW REPLACEMENT FUEL TANK INTERNAL FUEL LINE CONNECTION. INFORMATION WARRANTY INFORMATION Not applicable. This Service Information bulletin provides technical and repair procedure-related information.
B121919
Service Bulletin/Repair Instructions
Service Information May 2019 Engine Electrical Systems B12 19 19 Technical Service. On the affected vehicles a DME software error prevents the Check Control Message (CCM) "Low Engine Oil Level" to be displayed in instrument cluster (Kombi) when the engine oil level drops below the minimum level.
B662317
Service Bulletin/Repair Instructions
Service Information March 2018 Drivers Assistance Remote Control Systems B66 23 17 Technical Service This Service Information bulletin replaces SI B66 23 17 dated February 2018 CONTACTLESS TAILGATE (SMART OPENER) IS TOO SENSITIVE.
B011817
Service Bulletin/Repair Instructions
N63T HIGH PRESSURE FUEL PUMP HDP LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILES This Service Information bulletin supersedes SI B01 18 17 dated July 2018.
B012418
Service Bulletin/Repair Instructions
On the affected vehicles the CBS engine oil service interval has been reduced to 1 year/10000 miles to make these vehicles consistent with all other N63x engine equipped vehicles.
B613014
Service Bulletin/Repair Instructions
BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure.
B621118
Service Bulletin/Repair Instructions
BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: â?¢ Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.
B012318
Service Bulletin/Repair Instructions
N63 ENGINE OIL CONSUMPTION/BATTERY DRAIN CLASS ACTION LAW SUIT SETTLEMENT: FUTURE ENGINE OIL SERVICE BENEFIT CLASS VEHICLES (MODELS) Certain models of the following US specification BMW vehicles sold or leased in the United States and Puerto Rico are included.
B110113
Service Bulletin/Repair Instructions
N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
B111318
Service Bulletin/Repair Instructions
SERVICE ACTION: N63R ENGINE - CHECK AND REPLACE OIL FEED LINES AND THE CHARGE AIR COOLERS. This bulletin describes the procedures to inspect and if necessary replace the following components: * Turbo charger oil feed lines (leaking) * Charge air coolers (corrosion)
B111418
Service Bulletin/Repair Instructions
SERVICE ACTION: N63R ENGINE - CHECK AND REPLACE OIL FEED LINES AND THE MAP THERMOSTAT ELECTRICAL CONNECTOR. This bulletin describes the procedures to inspect and if necessary replace the following components: * Turbo charger oil feed lines (leaking) * Map thermostat and electrical harness (corrosion) Also, make sure that Service Bulletin B12 24 18 Service Action: Program Control Units, is completed when performing this Service Action.
B111618
Service Bulletin/Repair Instructions
DELIVERY STOP: N63R AND N63M ENGINE - CHECK ENGINE OIL SUPPLY CIRCUIT FOR CONTAMINATION. The engine oil pan and oil lubrication circuit may be contaminated with metal debris from the engine manufacturing process. AFFECTED VEHICLES This Recall Campaign) involves G12, G30 and G05 vehicles produced from June 26th 2018 to September 24th 2018. Vehicles which require this Recall Campaign to be completed will show it as "Open" when checked either in AIR, the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
B120918
Service Bulletin/Repair Instructions
NOISE FROM ENGINE WHEN STARTING. Noise when starting the engine. Engine making a rattling/grinding noise near the 12 volt starter motor. The following fault has been stored in the DME fault memory: * 21A511 - Start system, pinion starter motor: Timeout The following faults are also possible: * 21A504 - EGS, separation clutch: jammed open * 21A50A - Start system, pinion starter: Timeout successively occurred multiple times * 21A510 - Start system, EME: Timeout Consequential damage to flywheel (Torsional vibration damper) and automatic transmission may have also occurred. The starter motor is broken. It may be indicated by:
B122418
Service Bulletin/Repair Instructions
SERVICE ACTION: PROGRAM CONTROL UNITS (DME). Revised engine lubrication strategy has been implemented. Specifically, crankcase oil spraying jets will be activated at lower engine speeds, to improve pistons lubrication and cooling.
B122716
Service Bulletin/Repair Instructions
DIAGNOSING NON FUNCTIONING eDRIVE. * Vehicle will not go into "eDrive" * No pertinent electric drivetrain fault codes to assist with diagnosis * "eDrive" may be greyed-out in the Central Information Display (CID) and is not selectable * MSA deactivation * 12 volt battery failure * Intelligent Battery Sensor (IBS) failure.
B160818
Service Bulletin/Repair Instructions
SERVICE ACTION. CHECK AND, IF NECESSARY, REPLACE THE FUEL DELIVERY UNIT. The fuel delivery unit (in-tank fuel pump) may be the incorrect part installed for the Model/Market.
B170418
Service Bulletin/Repair Instructions
DELIVERY STOP. LOW TEMPERATURE COOLANT SYSTEM.A Delivery Stop has been issued (effective October 16, 2018) on Model Year 2019 BMW 5 and 7 Series vehicles that have been produced from September 13-14, 2018. There is a possibility that the affected vehicles do not have the correct amount of coolant in the low-temperature coolant system. Approximately 3 vehicles are affected by this delivery stop that have already been delivered to dealers. Affected vehicles show the campaign as ?Open? when checked either in Warranty Vehicle Inquiry, AIR or ISPA Next and identified with the description: STOP013433 B170418 Delivery Stop: Low Temperature Coolant System. The bulletin will be updated with more information when it becomes available.
B613017
Service Bulletin/Repair Instructions
RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B660817
Service Bulletin/Repair Instructions
REAR VIEW CAMERA FAILS TO DISPLAY IMAGE. Sporadically, when the rear view camera is activated, either via selecting reverse with the shift selector or by direct camera selection, no image appears in the display. Camera function returns after terminal change. Note: This error situation can rarely, if ever, be duplicated on demand. Head-unit interface software error for the rear view camera.
B720417
Service Bulletin/Repair Instructions
FALSE WARNINGS THAT THE FRONT PASSENGER SEAT IS OCCUPIED WITHOUT THE SEAT BELT BUCKLED. Acoustic and visual warnings indicate that the front passenger seat is occupied and the seat belt is not fastened, when the seat is actually unoccupied. If the situation is currently present, sit in the seat and move the seat to a different position then the POL (Passenger Occupancy Light) light will function correctly. In some cases the Air bag Warning Light was illuminated. Advanced Crash Safety Module (ACSM) fault "930A1C - Front passenger seat occupancy detection transmitting fault (moisture)" is stored. 1. Electronics (for example smart phones or laptops) are connected to the USB charging port or cigarette lighter and placed on the seat. 2. The seat was wet (e.g. very high humidity, spilled liquids or rain). 3. Faulty plug connection to Evaluation Electronics CIS (Capacitive Interior Sensing). 4. Excessive spacing between seat mat sensor signal wires and their grounding shield sleeve. * Drying the seat mat due to moisture. * If there is no moisture, secure loose cables and install 2 cable ties * If the 2 cables ties are already installed properly, replace the seat mat * Statement added to SI - do not replace the CIS electronics or the ACSM module for this siutation.
B111117
Service Bulletin/Repair Instructions
?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B270118
Service Bulletin/Repair Instructions
?DYNAMIC STABILTY CONTROL WARNING ON WITH LIMITED POWER STEERING ASSIST This Service Information bulletin replaces SI B34 09 16 dated January 2017 What's New: ? This SIB is a complete revision of B34 09 16. Steering feels heavy (limited power assist) The Dynamic Stability Control (DSC) light and Service Engine Soon light may be on. The following message may be displayed in the Check Control (CC): * CCM 350 "It is possible to continue to drive. All-wheel drive system." * Other CC messages may be stored related to: Restraint system / lane change warning / distance information / pedestrian protection. One or both of the following faults are stored in the DSC: * D36500 - Message fault (xDrive actuator information, ID: XDRV_ACT_INFO) - Timeout * D356E4 - Message fault (status of distribution of the longitudinal torque on the front axle rear axle, ID: ST_REPAT_XTRQ_FTAX_BAX) - Timeout The following faults can also be stored in the DDE or DME: * DDE: CD95E0 - Message (ST_REPAT_XTRQ_FTAX_BAX, 19.3.4,FX), Timeout: Message (status of distribution of longitudinal torque of front axle rear axle) from longitudinal torque distribution failed * DME: CDA056 - FlexRay, message (status of distribution of longitudinal torque of front axle rear axle / xDrive actuator information, 19.3.4): missing Internal fault in the transfer case control unit (Longitudinal Torque Module - LMV).
B661917
Service Bulletin/Repair Instructions
?SERVICE ACTION: CHECK AND REPLACE LANE CHANGE WARNING SENSOR. The Lane Change Warning sensor may have been produced with faulty components. This may lead to a failure of the Lane Change Warning system (SWW). Lane Change Warning sensor hardware defect.
B662017
Service Bulletin/Repair Instructions
?DISPLAY KEY IS NON-FUNCTIONAL. Display key is non-functional. Display key cannot be charged or switched on. Possibly defective display key.
B840616
Service Bulletin/Repair Instructions
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B520318
Service Bulletin/Repair Instructions
MEMORY SEAT ADJUSTMENT IS LIMITED: After programming the vehicle with ISTA 4.10.2x, the adjustment range of the memory seat may restricted.
B620618
Service Bulletin/Repair Instructions
FUEL GAUGE INCORRECTLY DISPLAYING LOW FUEL LEVEL: Occasionally, on restart after refueling, the fuel gauge will display the fuel level as low (minimum) and the range display will be at an implausible (maximum) value.
B660814
Service Bulletin/Repair Instructions
Side View Camera Does Not Display Picture.
B110117
Service Bulletin/Repair Instructions
N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT: This SI provides a new tool and a new procedure for the N63TU valve seals replacement.
B160417
Service Bulletin/Repair Instructions
DME FAULT CODE 194006 TANK LEAKAGE DETECTION MODULE, SOLENOID VALVE: JAMMED OPEN. Malfunction Indicator Lamp (MIL) is illuminated. The following fault code is stored in the DME: 194006 Tank leakage detection module, solenoid valve: jammed open is presentThe following fault code may also be stored with FC 194006: 190302 Fuel tank ventilation system micro-leak: Leakage larger than 0.5 mm. Vacuum leak in fuel tank ventilation system or an internal failure (pressure switch) of the NVLD (Natural Vacuum Leak Detection).
B513017
Service Bulletin/Repair Instructions
A-PILLAR WIND NOISE. At vehicle speeds above 60 mph, wind noise is heard from the vicinity of the A-pillar. Excessive gap between the roof trim strip and the A-pillar.
B620717
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER REMAINS DARK & DOES NOT START UP This Service Information bulletin replaces SI B62 07 17 dated May 2017 What's New: Changed affected production dates & options Procedure wording Changed I-level of software. G12 (7 Series) G30 (5 Series Sedan) Vehicles produced up to 3/1/2017. The instrument cluster (KOMBI) display does not appear when the vehicle is started. Software in the instrument cluster incorrectly initiates the safety mode causing the cluster display to remain dark.
B661117
Service Bulletin/Repair Instructions
ACC (ACTIVE CRUISE CONTROL): CANNOT DELETE FAULT CODE 022126. ACC fault code 022126 does not delete from ACC control unit fault code memory. May occur in combination with under-voltage fault codes: * BDC 0x80402F - Battery deeply discharged * BE6: 0x801405 - Under-voltage detected Insufficient control unit software.
B111217
Service Bulletin/Repair Instructions
N63R ENGINE OIL FILLING CAPACITY FOR XDRIVE VEHICLES. INFORMATION The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive. The correct engine oil capacity specification is 10.5 liters of engine oil. For more information also refer to B11 01 15.
B170517
Service Bulletin/Repair Instructions
SERVICE ACTION: REPLACE THE MOUNT FOR THE TRANSMISSION OIL COOLER THERMOSTAT. There may be a rattling noise coming from the engine area at the transmission oil cooler thermostat or (on xDrive models only) the transmission oil cooler lines coming into contact with the left front output shaft. The bracket that holds the transmission oil cooler thermostat to the left front frame rail may be defective
B410317
Service Bulletin/Repair Instructions
SERVICE ACTION: WATER INGRESS BENEATH LUGGAGE COMPARTMENT. Possible water leakage into luggage compartment through PVC weld on floor. Accumulation of water in luggage compartment may not be noticed due to drain location in the vicinity. Manufacturing process change moved PVC weld on underside of vehicle, beneath luggage compartment.
B520417
Service Bulletin/Repair Instructions
BACKREST NOISES WHEN UNDER LOAD. Pop noise coming from seat backrest when pressure exerted toward rear or while pulling away from a stop. Friction between top right rivet holding lordosis (back Lumbar support) valve block and backrest cushion spring.
B613417
Service Bulletin/Repair Instructions
SERVICE ACTION: PROGRAM CONTROL UNITS (GWS). After the engine start-up, gear (Drive or Reverse) cannot be selected. Message "No drive position change possible" is displayed in the CC display. Gear can be selected only after vehicle goes through the sleep cycle. Unfavorable GWS gear shifter software
B621017
Service Bulletin/Repair Instructions
ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, BMW Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error
B660617
Service Bulletin/Repair Instructions
THE SMART OPENER TAILGATE IS ACTIVATED TOO EASILY. The touchless tailgate opening/closing activation is: * Too sensitive * Randomly initiated Software error in the tailgate function module
B3106170621
Service Bulletin/Repair Instructions
Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC73 must appear in the text of your TEC claim.
B612817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F04B. One or several of the following check control messages (CCM) may be displayed: "Engine fault! Power loss" (CCM-ID: 29) "Powertrain malfunction!" (CCM-ID: 633) "Hybrid system malfunctioning!" (CCM-ID: 585) Note: The fault code 21F04B stated below may also be entered without any of the above mentioned CC messages being displayed A timing problem between the SME and the cell supervision circuit (CSC).
B620817
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER CANNOT BE PROGRAMMED. When programming the vehicle the instrument cluster fails to program. Missing software for instrument cluster.
SIM010917
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
SIM120517
Service Bulletin/Repair Instructions
Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks for
SISIB011317
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, LLC
B170217
Service Bulletin/Repair Instructions
CHECK CONTROL (CC) MESSAGE:"COOLANT LEVEL TOO LOW!" IS DISPLAYED. CC message: "Coolant level too low!" appears in the display. The cooling system wasn't efficiently bled during the factory fill.
B512517
Service Bulletin/Repair Instructions
SERVICE ACTION: REMOVE XDRIVE NAME PLATE FROM TRUNK LID. The xDrive name plate on the left side of the trunk was incorrectly installed at the factory and needs to be removed. The xDrive name plate on the left side of the trunk was incorrectly installed at the factory and needs to be removed.
B612117
Service Bulletin/Repair Instructions
HAZARD WARNING SWITCH FLICKERS AFTER ENGINE START. Hazard warning switch flickers after engine start. Faulty communication between hazard warning switch and Body Domain Controller (BDC).
B612717
Service Bulletin/Repair Instructions
In-stock, new vehicle instrument cluster displays the red CCM "Replace Battery". ? Improper handling of the vehicle/storage maintenance of the battery charge. ? Defective battery Note: The red CCM comes on when the state of charge of the battery drops to 30%. At this point the battery is heavily discharged and needs to be replaced.
B621616
Service Bulletin/Repair Instructions
WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.
B660417
Service Bulletin/Repair Instructions
LOCKING FUNCTION INOPERATIVE FROM THE HANDLE, ON VEHICLES WITH COMFORT ACCESS. Touching a door handle does not activate locking/closing function after exit from vehicle via Comfort Access. All door handles are affected when vehicle is wet or after rain. Keyless entry is possible via the remote control key Moisture penetration between locking sensor and handle support.
B112216
Service Bulletin/Repair Instructions
?"ENGINE OIL PRESSURE" ON LOW MILEAGE CARS. Check Control Message (CCM-212) states: "Engine Oil Pressure. Stop Carefully" The following codes may be stored in the DME fault memory" 1C2002 - Engine oil pump, pressure too low 1FB801 - CCM (ID212) - Oil pressure Also, the vehicle's mileage is very low (below 60 miles), the fault frequency shows only "one" occurrence; faults are not currently present and cannot be reproduced. CAUSE Unfavorable DME software application."
B340317
Service Bulletin/Repair Instructions
DYNAMIC STABILITY CONTROL FAILURE. Instrument cluster indicates Dynamic Stability Control (DSC) failure. You cannot establish communication with the DSC control unit. Associated control units (DME, ACSM) register DSC-related communication time-outs. After battery reset, DSC operates normally and has no faults registered. Software in the DSC control module.
B340417
Service Bulletin/Repair Instructions
?DSC WARNING LAMP ILLUMINATED AFTER TRANSPORT MODE DEACTIVATION. After vehicle start-up from transport mode, the DSC warning lamp flashes. CC message driving stabilization restricted" is displayed in the CID. The following faults are entered in the fault memory: 0x482394 EPS control unit: Initialization fault steering angle, loss of multi-turn value. 0x48078B DSC control unit: Initialization fault EPS, adjustment required. The order of transport mode deactivation and steering angle sensor initialization reversed. While in transport mode, the steering angle sensor loses calibration on every terminal change. During the QCI service, transport mode deactivation is supposed to occur prior to steering angle sensor initialization. When this is reversed, calibration is lost."
B511317
Service Bulletin/Repair Instructions
WIND NOISE FROM REAR SIDE WINDOW. At highway speed, wind noise is heard from either rear side window. CAUSE Gap between the window guide and the window guide bar. Replace the window guide after verification of cause.
B511517
Service Bulletin/Repair Instructions
HOOD DOES NOT RELEASE PROPERLY. Hood lever is pulled twice but the hood only achieves the pre-latch position on one side while the other is still latched. Downward pressure on the side of the hood that remains latched will release it to the pre-latch position. After pre-latch position is achieved on both sides, the hood unlatch lever must be pulled again to achieve unlatched position. Hood latch mechanical release is not operating properly. Neither hood latch can be released to the fully open position until both have achieved the pre-latch position.
B611817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F02A. Upon starting the vehicle, the following CC message is displayed to the customer: Powertrain malfunction!" (CCM-ID: 633) In addition, one or several of the following CC message(s) may be displayed: "Charging not possible" (CCM-ID: 804), "Hybrid system malfunctioning!" (CCM-ID: 585), "Drive. No restart" (CCM-ID: 586) or "Engine fault! Power loss" (CCM-ID: 29). Possible hardware defect of the safety box."
B612217
Service Bulletin/Repair Instructions
DIAGNOSTIC COMMUNICATION WITH FLEXRAY CONTROL MODULES NOT POSSIBLE. There are no customer complaints associated with this issue. The following control modules do not respond when diagnosing the vehicle with ISTA: Advanced Crash and Safety Management (ACSM) Digital Motor Electronics (DME) Dynamic Stability Control (DSC) Electric Active Roll Stabilization, Rear (EARSH) Electric Active Roll Stabilization, Front EARSV) Electrical Machine Electronics (EME) Electromechanical Power Steering (EPS) Integral Active Steering (HSR) Optional Equipment System (SAS) Vertical Dynamics Platform (VDP) Transfer Box (VTG) CAUSE Body Domain Controller (BDC) diagnostic communication error.
B620617
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER RESETS. Instrument cluster sporadically flickers and/or fails. Instrument cluster performs spontaneous reset. Instrument cluster software.
B840311
Service Bulletin/Repair Instructions
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
Service Bulletin/Repair Instructions
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
Service Bulletin/Repair Instructions
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B410117
Service Bulletin/Repair Instructions
?SERVICE ACTION: PVC WELD SEAM BENEATH LUGGAGE COMPARTMENT . Possible water leakage into luggage compartment through PVC weld on floor. Improperly applied PVC weld on underside of vehicle, beneath luggage compartment.
B511017
Service Bulletin/Repair Instructions
?LOOSE, NOISY, BMW EMBLEM ON TAILGATE . BMW emblem on tailgate wobbles and makes crackling noise when touched. Incorrect initial installation.
B520816
Service Bulletin/Repair Instructions
FRONT SEAT ADJUSTMENT, WRONG DISPLAY/ERROR RECOGNITION (FAULTY DETECTION) IN CID What is new ? G30 has been added. ? "Correction" has changed from programming solution to replace seat switch. ? Procedure" has been changed to replace the seat switch instead of programming. ? ""Parts Information"" has been added for the seat switch. ? Warranty Labor Ops have changed to reflect the updated procedure to replace the seat switch. This Service Information bulletin supersedes SI B52 08 16 dated October 2016. . The seat adjustment is erroneously displayed in the Central Information Display (CID) even though no adjustment was made at the seat switch. Front seat adjustment switch"
B540117
Service Bulletin/Repair Instructions
?GLASS ROOF NOT CLOSING . Glass roof will not close. At least one of the following fault codes is stored: 30215: Slide/tilt sunroof: invalid characteristic curve, no standardization exists 30295: Electric sliding headliner: invalid characteristic curve, no standardization exists 302A0: Electric sliding headliner: System not standardized 30220: Slide/tilt sunroof: System not standardized Roof function center software.
B610917
Service Bulletin/Repair Instructions
?FAULT CODE CD0600 IN CENTRAL GATEWAY MODULE . Discovered during vehicle diagnosis, Fault Code CD0600 "Ethernet unexpected linkdown" is recorded in Central Gateway Module (ZGW). No malfunction perceptible to the customer. Erroneous fault memory entry.
B630217
Service Bulletin/Repair Instructions
?CCM DISPLAYED FOR TURN SIGNAL OR REVERSE LIGHTS G30 (5 Series Sedan) Produced to March 01, 2017 SITUATION One of the following Check Control Messages (CCM) is displayed: "Turn indicator at the front left/right faulty" "Reversing light faulty" Turn signal flash frequency is double the normal frequency. OR Reverse bulb is illuminated for very short time. One or more of the following fault codes is stored in the Body Domain Controller (BDC): 0x80419C or 0x80419D: Front turn indicator 0x80486A or 0x80486B: Reversing light CAUSE BDC software CORRECTION Reprogram and encode the vehicle.
B630916
Service Bulletin/Repair Instructions
?TAILLIGHT FLICKER WHEN TURN SIGNAL AND BRAKE LIGHT ACTIVE . Taillight flickers when turn signal and brake light are active; see video in this link: tinyurl.com/zmr65st When the following preconditions occur simultaneously: Engine on (idle). Tail light active (switched on). Brake light active (through actuation of the brake pedal). Turn signal active (switched on). Current fluctuations reduce the voltage to the tail light.
B650417
Service Bulletin/Repair Instructions
?CROSS TRAFFIC WARNING MISSING FROM INTEGRATED OWNERS MANUAL . The crossing traffic warning (right of way warning) section is missing from the integral owner's manual (IBA). The picture below shows the missing text. Software error in the Head unit IBA file
B650616
Service Bulletin/Repair Instructions
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
Service Bulletin/Repair Instructions
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B661016
Service Bulletin/Repair Instructions
?GARAGE DOOR OPENER CANNOT BE PROGRAMMED Whats new: ? "Model": G30 (5 Series) added . The vehicle's rear view mirror integrated universal remote control is incompatible with some garage door (or fence) opener devices installed at the driver's residence and/or business. If the garage door opener was manufactured before 1993, it will not be compatible with any HomeLink device. Installing the compatibility bridge will NOT link these units. This is due to several incompatible frequency's used before 1993.
B111715
Service Bulletin/Repair Instructions
?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 "Removing and installing/replacing upper oil sump" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. "All threads must be cleaned with screw tap" Or "Clean all threads with screw tap. Order number 81 43 0 402 559" Or "Clean all threads with a thread cutter". The current repair instruction terminology will be modified to include this information.
B340116
Service Bulletin/Repair Instructions
?DYNAMIC STABILITY CONTROL (DSC) WARNING LAMP, LIGHTS UP This Service Information bulletin supersedes SI 34 01 16 dated October 2016 . Various "DSC warning lamps lights up in the instrument cluster, including the display: "Suspension control system failed". DSC control unit.
B510317
Service Bulletin/Repair Instructions
?B-PILLAR WIND NOISE . While driving at highway speeds, wind noise can be heard from the rear of either or both front doors. Sealing lip of inner window cavity seal is bent as shown on left below. Seal placement should be as shown on right, parallel to green line.
B610517
Service Bulletin/Repair Instructions
?WINDOW WASHER FLOW INTERRUPTION . Front windshield washers spray poorly or not at all. CAUSE Partially or completely pinched supply tube caused by misplaced tube holder on hood hinge. Reposition and secure tube holder on the gas pressure spring.
B000117
Service Bulletin/Repair Instructions
?SI B00 01 17 General Maintenance and Hints for G30 QUALITY FEEDBACK
B650915
Service Bulletin/Repair Instructions
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
B630516
Service Bulletin/Repair Instructions
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by "condensation" rather than a "water leak" into the headlight housing, there will be misting/condensation in "both headlights."
B652616
Service Bulletin/Repair Instructions
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B340516
Service Bulletin/Repair Instructions
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652316
Service Bulletin/Repair Instructions
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B652416
Service Bulletin/Repair Instructions
NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes "without a cash option" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes "without cash option". UPDATE Install new map data.
B652516
Service Bulletin/Repair Instructions
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B662116
Service Bulletin/Repair Instructions
KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B512416
Service Bulletin/Repair Instructions
WATER LEAKING INTO REAR COMPARTMENT. Water is found in rear compartment. CAUSE Seal around fuel filler tube (located by red lines) is not effective. Replace cover pot (bowl).
B511615
Service Bulletin/Repair Instructions
Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2
B661816
Service Bulletin/Repair Instructions
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B840516
Service Bulletin/Repair Instructions
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B120516
Service Bulletin/Repair Instructions
N55 - ENGINE MALFUNCTION WARNING DUE TO VAPOR FORMING IN THE FUEL SYSTEM This Service Information bulletin supersedes SI B12 05 16 dated April 2016. The Engine "Drivetrain Malfunction" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or "stop and go" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures.
B621016
Service Bulletin/Repair Instructions
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B110916
Service Bulletin/Repair Instructions
N63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
B320616
Service Bulletin/Repair Instructions
Troubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
B370115
Service Bulletin/Repair Instructions
Service Action: Replace Left Rear Air Spring. Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.
B620716
Service Bulletin/Repair Instructions
Unintentional Active ECO-PRO Bonus Miles Reset. Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.
B660916
Service Bulletin/Repair Instructions
"Collision Warning Failed" or "Pedestrian Warning Failed" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the "green lines"
B840314
Service Bulletin/Repair Instructions
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
B840715
Service Bulletin/Repair Instructions
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
B640316
Service Bulletin/Repair Instructions
Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 "This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm 10151190 20181210 B640316 20160301 Service Bulletin/Repair Instructions BMW ACTIVE HYBRID 3 2013 EQUIPMENT Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
B650716
Service Bulletin/Repair Instructions
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
B510316
Service Bulletin/Repair Instructions
SUBJECT Noise from the Power Window. When operating front power windows a chattering noise can be heard. Front window regulator is lacking lubrication
B610314
Service Bulletin/Repair Instructions
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B650216
Service Bulletin/Repair Instructions
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B621415
Service Bulletin/Repair Instructions
Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.