B065725
Other
Right Engine Hood Hinge Return
Vehicle report
2012 BMW 640I
Service bulletins
223 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B340914
Service Bulletin/Repair Instructions
The Dynamic Stability Control (DSC) warning light comes on while driving. The following DSC fault codes for the wheel speed sensors are stored: 480712 and/or 480715 and/or 480718 and/or 48071B They cannot be cleared, even though the wheel speed sensors work correctly and no problem can be found with the wiring harness.
B651523
Service Bulletin/Repair Instructions
After programming the head unit (HU-H2), activating the FSC (German word Freischaltcode) Enabling Codes repeatedly fails.
B010122
Service Bulletin/Repair Instructions
With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered into a nationwide settlement with the plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC.
B650414
Service Bulletin/Repair Instructions
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
SIB010921
Service Bulletin/Repair Instructions
Component-Specific Limited Warranty Extension. For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Leak Diagnosis Module with hose assembly (NVLD, shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date. For eligible MY 2017 BMW 530i Sedan and xDrive (B460) vehicles that are currently registered in the State of California (CA) or a State that has fully adopted the State of California PZEV/SULEV regulation (CT, ME, MD, MA, NJ, NY, RI, and VT), the standard component-related coverage for the NVLD is 15 years/150,000 miles. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Over time, the Leak Diagnosis Module (NVLD) (with connected hose) component material may fail, this can create a fine leak to develop in the Evaporative Emission Control System (EVAP). Should this occur, corresponding fault codes will be stored in the DME memory and the MIL (Malfunction Indicator Lamp) will illuminate.
SIB640821
Service Bulletin/Repair Instructions
The air conditioning cycles from cold to warm air while driving or while at a stand still. The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings. In some cases the air conditioning may have stopped blowing cold air altogether.
SIB662419
Service Bulletin/Repair Instructions
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.
SIB651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B111614
Service Bulletin/Repair Instructions
This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
B341019
Service Bulletin/Repair Instructions
Inform the customer during a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty, dynamic driving styles. As a side effect of the highest possible brake performance, customers are likely to hear noises due to the extremely resilient materials. In the same conversation, inform the customer that his/her braking performance can help ensure that the noises do not occur or disappear quickly.
B651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B840221
Service Bulletin/Repair Instructions
The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.
B011321
Service Bulletin/Repair Instructions
CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
B840121
Service Bulletin/Repair Instructions
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
B340414
Service Bulletin/Repair Instructions
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B130720
Service Bulletin/Repair Instructions
INCORRECT TORQUE SPECIFICATION FOR THE HIGH-PRESSURE PUMP IN ISTA: The current version of ISTA states the incorrect tightening torque for the High-Pressure pump M6 mounting bolts to the cylinder head cover. The correct tightening torque is only 12 Nm for the M6 bolts.
B340515
Service Bulletin/Repair Instructions
TICKING NOISE FROM THE FRONT AXLE WHEN CORNERING: The customer may complain of a metallic ticking noise from the front axle, when cornering, maneuvering, parking or pulling away from a parking space.
B310112
Service Bulletin/Repair Instructions
CRACKING NOISES FROM THE FRONTAXLE AREA WHILE TURNING THE WHEELS, WHEN STATION: Cracking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.
B340517
Service Bulletin/Repair Instructions
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B650709
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B513016
Service Bulletin/Repair Instructions
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B652214
Service Bulletin/Repair Instructions
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B840214
Service Bulletin/Repair Instructions
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B010518
Service Bulletin/Repair Instructions
LIMITED WARRANTY EXTENSIONTO 10 YEARS/120000 MILES: This Service Information Bulletin replaces SI B01 05 18 dated July 2019. Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.
B521519
Service Bulletin/Repair Instructions
FRONT SEAT HAS SIDE TO SIDE PLAY AND CAN MAKE NOISES WHEN CORNERING. Either or both of the front seats has side to side (lateral) play, and can make noises when cornering.
B651519
Service Bulletin/Repair Instructions
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
613512
Service Bulletin/Repair Instructions
Radio and Air Conditioning Functions Inoperative, When Vehicle is Moving. All audio and heating/air conditioning functions cannot be controlled when the vehicle is moving. After the vehicle is turned off and has entered sleep mode (after approximately 30 minutes), the system operates normally. CAUSE: Software error in the audio and air conditioning control panel.
651512
Service Bulletin/Repair Instructions
Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
660612
Service Bulletin/Repair Instructions
Lane Change Warning Lamps on Side View Mirrors Are Too Dark. The lane change warning lamps (small and triangle-shaped) on the exterior door mirrors are too dark. This may occur when driving from light to dark conditions, such as: * Entering a tunnel * At twilight CAUSE: RLSS (Rain Light Solar Sensor) hardware error.
512012
Service Bulletin/Repair Instructions
Rattling Noise from Underneath the Instrument Panel. A rattling or clattering noise may be heard from the driver's or passenger foot well area while driving. CAUSE Tolerance excessive between the footwell air duct and the securing hooks.
110712
Service Bulletin/Repair Instructions
N63 Engine: Oil Consumption and/or Rough Running Complaints. The vehicle may consume engine oil above the permissible specification, and may run rough at times. White or blue smoke may also be seen exiting the exhaust system. CAUSE The construction material of the crankcase ventilation connection lines and vent pipes may become brittle from engine compartment temperatures.
121412
Service Bulletin/Repair Instructions
N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
B111216
Service Bulletin/Repair Instructions
The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM (fluoroelastomer) rubber material. The FPM rubber material is engine heat resistant. Or The plastic corrugated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
B122319
Service Bulletin/Repair Instructions
DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL. In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
B012118
Service Bulletin/Repair Instructions
N63 ENGINE: OIL CONSUMPTION CLASS ACTION SETTLEMENT DIAGNOSIS AND REPAIR PROCEDURES. While engine oil consumption may create a customer inconvenience in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle.
B110919
Service Bulletin/Repair Instructions
N55 ENGINE: FC 28A0 OR 101F01 THROTTLE VALVE OPENING ANGLE. The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.
B160419
Service Bulletin/Repair Instructions
NEW REPLACEMENT FUEL TANK INTERNAL FUEL LINE CONNECTION. INFORMATION WARRANTY INFORMATION Not applicable. This Service Information bulletin provides technical and repair procedure-related information.
B520719
Service Bulletin/Repair Instructions
NOISE FROM THE FRONT SEATS WHEN ADJUSTING THE SEAT LENGTH.
B520819
Service Bulletin/Repair Instructions
FRONT SEAT BACKREST MAKES A CRACKING NOISE WHEN FOLDED FORWARD.
B520919
Service Bulletin/Repair Instructions
CRACKING NOISE FROM SEAT BACKREST. Groaning/Cracking noises are heard from the front seat backrest when the vehicle is cornering.
B121919
Service Bulletin/Repair Instructions
Service Information May 2019 Engine Electrical Systems B12 19 19 Technical Service. On the affected vehicles a DME software error prevents the Check Control Message (CCM) "Low Engine Oil Level" to be displayed in instrument cluster (Kombi) when the engine oil level drops below the minimum level.
B840311
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT ACTIVATION VIA DCSNET FOR BMW ASSIST.
B012418
Service Bulletin/Repair Instructions
On the affected vehicles the CBS engine oil service interval has been reduced to 1 year/10000 miles to make these vehicles consistent with all other N63x engine equipped vehicles.
B621118
Service Bulletin/Repair Instructions
BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: â?¢ Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.
B110113
Service Bulletin/Repair Instructions
N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
B613017
Service Bulletin/Repair Instructions
RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B110815
Service Bulletin/Repair Instructions
N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon.
B111117
Service Bulletin/Repair Instructions
?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B840616
Service Bulletin/Repair Instructions
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B520318
Service Bulletin/Repair Instructions
MEMORY SEAT ADJUSTMENT IS LIMITED: After programming the vehicle with ISTA 4.10.2x, the adjustment range of the memory seat may restricted.
B651117
Service Bulletin/Repair Instructions
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START: Navigation system will not start at all or the: ÒNavigation system startsÓ message is permanently displayed; or
B840818
Service Bulletin/Repair Instructions
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:
B621215
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
B660518
Service Bulletin/Repair Instructions
COMFORT ACCESS SPORADICALLY INACTIVE VIA DOOR HANDLE: Sporadically, CA (Comfort Access) locking or unlocking of the vehicle does not work via the door handles.
B661018
Service Bulletin/Repair Instructions
REAR VIEW CAMERA CANNOT BE CONTROLLED VIA IDRIVE: When the Parking menu is active (reverse gear selected) in the CID (Central Information Display), activation or deactivation of the rear view camera via the iDrive controller does not work.
B840718
Service Bulletin/Repair Instructions
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition.
B630516
Service Bulletin/Repair Instructions
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION: Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside.
B110115
Service Bulletin/Repair Instructions
Engine Oil Quick Reference Chart and Drain Plug Torque: The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive.
B841117
Service Bulletin/Repair Instructions
BMW APPS RANDOMLY STARTS PLAYING ON ITS OWN: While listening to FM, or AM, or Satellite Radio (SDARs), the audio source randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.
B650318
Service Bulletin/Repair Instructions
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback.
B840314
Service Bulletin/Repair Instructions
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B650915
Service Bulletin/Repair Instructions
NBT Head Unit High (HU-H) Resets Intermittently or Permanently
B660814
Service Bulletin/Repair Instructions
Side View Camera Does Not Display Picture.
SIM010717
Service Bulletin/Repair Instructions
The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
SIM010917
Service Bulletin/Repair Instructions
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
B110117
Service Bulletin/Repair Instructions
N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT. This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
B340117
Service Bulletin/Repair Instructions
VIBRATION WHILE BRAKING. Vibration while braking is noticed: ? Most commonly when coming to a stop from higher speeds ? Less prominent when brakes are cold. ? After wheel balancing, the problem still exists. ? All other diagnosis according to SI B34 10 16 have no results. Over time, the original style NAO brake pads can develop friction variations.
B621616
Service Bulletin/Repair Instructions
WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.
B130315
Service Bulletin/Repair Instructions
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B840316
Service Bulletin/Repair Instructions
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
Service Bulletin/Repair Instructions
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B620317
Service Bulletin/Repair Instructions
?SERVICE ACTION: INSTRUMENT CLUSTER DISPLAY IN KM/H . When the instrument cluster's digital speedometer has been set to display metric speed and distance values, there is no display of the miles per hour. US regulations specify that even with the instruments set to display metric values, a "Miles per hour" display must also be present for immediate visual reference. To confirm language settings use the iDrive controller: Menu, Vehicle Settings, Language/Units, then - Distance - Dig (digital) Speedometer Instrument Cluster (KOMBI) software error.
B650616
Service Bulletin/Repair Instructions
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
Service Bulletin/Repair Instructions
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B111715
Service Bulletin/Repair Instructions
?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 "Removing and installing/replacing upper oil sump" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. "All threads must be cleaned with screw tap" Or "Clean all threads with screw tap. Order number 81 43 0 402 559" Or "Clean all threads with a thread cutter". The current repair instruction terminology will be modified to include this information.
B840716
Service Bulletin/Repair Instructions
?After programming with ISTA/P 3.55.0 or a more recent version, the customer can no longer send ?Edit start time? signal for climate control system can only send an ?Activate now? signal for climate control system.
B612716
Service Bulletin/Repair Instructions
SERVICE ACTION: PROGRAMMING CONTROL UNITS (REAR WINDOW HEATING). Under unfavorable conditions, activation of the rear window heating may overload its fuse. Software allows unfavorable activation.
B651316
Service Bulletin/Repair Instructions
NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing This Service Information bulletin supersedes SI B65 13 16 dated July 2016.. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will set a fault in the Head Unit (NBT-EVO), Fault Code "B7F87A: Burgler Actively Registered / Component Protection Active" This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called "Trusted VIN"
B652616
Service Bulletin/Repair Instructions
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B340516
Service Bulletin/Repair Instructions
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652016
Service Bulletin/Repair Instructions
CID Split Screen Always Changes Back to Compass Display. This Service Information bulletin Replaces SI B65 20 16 dated June 2016. After starting the vehicle, the Control Display (CID) right side (split screen) display does not stay on the last selection made by the driver. Within 30 seconds of starting the right side of the display changes by itself to the compass view. Software error (Head Unit NBT-EVO ID5) was introduced with ISTA/P V3.58.0 (16-03-502 I Level).
B652316
Service Bulletin/Repair Instructions
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B652416
Service Bulletin/Repair Instructions
NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes "without a cash option" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes "without cash option". UPDATE Install new map data.
B652516
Service Bulletin/Repair Instructions
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B512416
Service Bulletin/Repair Instructions
WATER LEAKING INTO REAR COMPARTMENT. Water is found in rear compartment. CAUSE Seal around fuel filler tube (located by red lines) is not effective. Replace cover pot (bowl).
B661616
Service Bulletin/Repair Instructions
BUZZING NOISE HEARD COMING FROM STEERING WHEEL. While driving at highway speeds, on older (worn) road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system
B010515
Service Bulletin/Repair Instructions
IN-TANK FUEL DELIVERY MODULE (PUMP): LIMITED WARRANTY EXTENSION TO 10 YEARS WITHOUT MILEAGE LIMITATION. INFORMATION On the above-referenced vehicles, BMW of North America, LLC ("BMW NA") is extending the limited warranty for the In-tank fuel delivery module (pump) to 10 years without mileage limitation as determined by the vehicle's original in-service date. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA sent VIN-specific customer notification letters the week of July 13, 2015 in a "phased" release. A sample letter is attached.
B011016
Service Bulletin/Repair Instructions
N55 PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the eligible vehicles, BMW of North America, LLC ("BMW NA") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release.
B320716
Service Bulletin/Repair Instructions
NO HEATING IN ALCANTARA STEERING WHEEL. The Alcantara steering wheel, which is used in Competition Edition, does not contain heating elements.
B511615
Service Bulletin/Repair Instructions
Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2
B661816
Service Bulletin/Repair Instructions
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B840516
Service Bulletin/Repair Instructions
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B330416
Service Bulletin/Repair Instructions
Delivery Stop: Replace Rear Differential.
B120516
Service Bulletin/Repair Instructions
N55 - ENGINE MALFUNCTION WARNING DUE TO VAPOR FORMING IN THE FUEL SYSTEM This Service Information bulletin supersedes SI B12 05 16 dated April 2016. The Engine "Drivetrain Malfunction" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or "stop and go" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures.
B511516
Service Bulletin/Repair Instructions
Delivery Stop - Check/Replace Windshield Sealing This Service Information Bulletin supersedes SI B51 15 16 dated June 2016. INFORMATION Reimbursement for this Service Action will be via normal claim entry.
B621016
Service Bulletin/Repair Instructions
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B110916
Service Bulletin/Repair Instructions
N63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
B320616
Service Bulletin/Repair Instructions
Troubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
B620716
Service Bulletin/Repair Instructions
Unintentional Active ECO-PRO Bonus Miles Reset. Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.
B660916
Service Bulletin/Repair Instructions
"Collision Warning Failed" or "Pedestrian Warning Failed" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the "green lines"
B520116
Service Bulletin/Repair Instructions
Front Seat Backrests Vibrates on Rough Roads. Both front seat backrests vibrate and rattle while driving over rough roads with the seat in an unloaded condition (no pressure applied on the backrest). Play at the inner backrest pivot point.
B840715
Service Bulletin/Repair Instructions
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
B640316
Service Bulletin/Repair Instructions
Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 "This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm 10151190 20181210 B640316 20160301 Service Bulletin/Repair Instructions BMW 535I 2014 EQUIPMENT Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
B650716
Service Bulletin/Repair Instructions
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
B610314
Service Bulletin/Repair Instructions
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B650216
Service Bulletin/Repair Instructions
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B161514
Service Bulletin/Repair Instructions
SI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.
B510116
Service Bulletin/Repair Instructions
Heated rear window control module requires a software update. The electrical load of the heated rear window may cause the fuse to overheat and fail. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
B160915
Service Bulletin/Repair Instructions
SI B16 09 15 Fuel Supply Systems. December 2015 Technical Service. This Service Information bulletin supersedes SI 26 01 15 dated November 2015. The wrong temperature sensor for the Natural Vacuum Leak Detection (NVLD) may have been installed.
B340614
Service Bulletin/Repair Instructions
?SI B34 06 14December 2015 BrakesTechnical Service This Service Information bulletin supersedes SI 34 06 14 December 2014. designates changes to this revision SUBJECT M5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.
B612215
Service Bulletin/Repair Instructions
Rear Window Defroster is Inoperative. The rear window defroster no longer works. Fuse 203 (30A) in the rear power distribution box is blown and the power distribution box may show signs of overheating. Excessive power consumption of the rear window defroster overloads the circuit.
B620715
Service Bulletin/Repair Instructions
Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles "arriving" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed "prior" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2.
B621015
Service Bulletin/Repair Instructions
Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 "display backlighting and graphics PCB switched off" stored. Kombi software.
B270415
Service Bulletin/Repair Instructions
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B270315
Service Bulletin/Repair Instructions
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
B130215
Service Bulletin/Repair Instructions
?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail.
B651015
Service Bulletin/Repair Instructions
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B613014
Service Bulletin/Repair Instructions
BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is "applicable" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
B620415
Service Bulletin/Repair Instructions
Service Action: Programming Control Units. Sporadically the vehicle cannot be started, due to a discharged battery caused by a software glitch in the instrument cluster.
B360215
Service Bulletin/Repair Instructions
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B110614
Service Bulletin/Repair Instructions
This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying "time-based" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see "Warranty Inf 10152301 20181217 B110614 20150401 Service Bulletin/Repair Instructions BMW M5 2014 EQUIPMENT This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf
B660115
Service Bulletin/Repair Instructions
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B110715
Service Bulletin/Repair Instructions
N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled "N63: Drivability after CCP." Follow the recommendations received.
B840514
Service Bulletin/Repair Instructions
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
111614
Service Bulletin/Repair Instructions
This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard.
270213
Service Bulletin/Repair Instructions
SI B27 02 13February 2015 Intermediate and Special Transmission Technical Service This Service Information bulletin supersedes SI B27 02 13 dated June 2013. designates changes to this revision SUBJECT Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
610314
Service Bulletin/Repair Instructions
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
650414
Service Bulletin/Repair Instructions
Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself.
110215
Service Bulletin/Repair Instructions
SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)
110614
Service Bulletin/Repair Instructions
This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: z Hot-Film Air Mass Sensors z PIEZO High Pressure Fuel Injectors z Engine Vacuum Pump z Fuel System Low Pressure Sensor/Feed Line z Fresh Air Intake Turbo Seals z Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying "time-based" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see "Warranty Information" section below).
120415
Service Bulletin/Repair Instructions
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
120915
Service Bulletin/Repair Instructions
SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the "fuel consumption, current" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold.
123814
Service Bulletin/Repair Instructions
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
650509
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
651312
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
652413
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
840115
Service Bulletin/Repair Instructions
MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received.
110713
Service Bulletin/Repair Instructions
The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
122114
Service Bulletin/Repair Instructions
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated and, while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Vehicles with option 610 (Head-Up Display) are not affected. Follow the ISTA/D test plan for the applicable faults stored in the DME. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling.
130712
Service Bulletin/Repair Instructions
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
161514
Service Bulletin/Repair Instructions
NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
340514
Service Bulletin/Repair Instructions
Dynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software
340614
Service Bulletin/Repair Instructions
M5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.
613014
Service Bulletin/Repair Instructions
BMW Maintenance Program: 12-Volt Battery Replacement Measure.
652214
Service Bulletin/Repair Instructions
Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
840412
Service Bulletin/Repair Instructions
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
840514
Service Bulletin/Repair Instructions
Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.
110413
Service Bulletin/Repair Instructions
N63TU Engine: Engine Oil Consumption. The customer complains that the "low engine oil" message is displayed too frequently. CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: z Turbocharger z Crankcase ventilation z Engine gasket leaks z Internal engine tolerances and sealing z Improper filling or topping up Use the troubleshooting procedure below to help identify the cause.
513314
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
652013
Service Bulletin/Repair Instructions
Vehicle inTransport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
280114
Service Bulletin/Repair Instructions
DCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
631114
Service Bulletin/Repair Instructions
LED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
651914
Service Bulletin/Repair Instructions
DWA Siren Malfunction. When the anti-theft alarm (DWA) is triggered, the horn comes on instead of the alarm siren. DWA internal monitoring is too sensitive.
660814
Service Bulletin/Repair Instructions
Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
8403014
Service Bulletin/Repair Instructions
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
SIB-63-11-14
Service Bulletin/Repair Instructions
BMW: ON SOME VEHICLES, WHEN STARTING, LOW BEAM, WITH 0552 OPTION, WOULD BRIEFLY FLASHES, DUE TO A FAULTY LED MAIN LIGHT MODULE THAT NEEDS REPLACING. MODEL 2008-14 F01, F02, F06, F07, F10, F12, F13, F25. *PE
511613
Service Bulletin/Repair Instructions
Bang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.
010414
Service Bulletin/Repair Instructions
External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
650214
Service Bulletin/Repair Instructions
Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
652113
Service Bulletin/Repair Instructions
When Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
660414
Service Bulletin/Repair Instructions
Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
660614
Service Bulletin/Repair Instructions
Rear View Camera Does Not Display Image on CID. After engaging the reverse gear, the reversing camera does not display a picture in the CID (Central Information Display). CAUSE The drive mechanism for the roundel actuation in the boot lid is faulty.
840214
Service Bulletin/Repair Instructions
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
360314
Service Bulletin/Repair Instructions
RDC: Incorrect Tire Position Displayed with Air Pressure Drop. When there is a low tire pressure warning, in some cases the position of the affected tire may be incorrectly displayed in the instrument cluster and CD (Control Display). Software error in the RDC (tire pressure control) module in conjunction with wheel electronics part number 4 078 787 or 4 079 152.
840314
Service Bulletin/Repair Instructions
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
310112
Service Bulletin/Repair Instructions
Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
340213
Service Bulletin/Repair Instructions
Incorrect Remaining Service Life from CBS Data for Brake Pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
360211
Service Bulletin/Repair Instructions
Tire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
620613
Service Bulletin/Repair Instructions
Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
120113
Service Bulletin/Repair Instructions
Transmission Intermittently Goes into "P" or "N" After MSA Engine Start. After an MSA engine start, the transmission intermittently goes into the Park (P) or Neutral (N) position without any customer influence. This problem can be sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software
310312
Service Bulletin/Repair Instructions
Groaning Noise from Front Axle. Groaning noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or over uneven road surfaces. CAUSE Hydraulic mount in tension strut
650514
Service Bulletin/Repair Instructions
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
360114
Service Bulletin/Repair Instructions
Fitting Winter Tires Properly to Vehicles with Ceramic Brakes. Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes
612213
Service Bulletin/Repair Instructions
"Increased battery discharge!" CC Message upon Startup. CAUSE A software error in the Intelligent Battery Sensor causes an incorrect State of Charge (SoC) to be stored in the DME. The power management system then interprets this as a heavily discharged battery and informs the customer via a CC message. In reality, the battery does not have a problem.
840114
Service Bulletin/Repair Instructions
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
652313
Service Bulletin/Repair Instructions
Headunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
840613
Service Bulletin/Repair Instructions
iPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
840913
Service Bulletin/Repair Instructions
My BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
630414
Service Bulletin/Repair Instructions
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
652513
Service Bulletin/Repair Instructions
ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST "My Info" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
653009
Service Bulletin/Repair Instructions
Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
121713
Service Bulletin/Repair Instructions
N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
611813
Service Bulletin/Repair Instructions
Service Action: Program Control Units (CAS). The Car Access System (CAS) software is incorrect, allowing the rear deck lid to be open when the convertible top compartment cover is in the intermediate position. This can cause the convertible top compartment cover to collide with the rear deck lid. AFFECTED VEHICLES This Service Action involves F12 vehicles. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 655. If code number 655 has been punched out, the campaign has already been performed. If code number 655 has not been punched out, it will be necessary to utilize the "Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair.
130413
Service Bulletin/Repair Instructions
N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
640113
Service Bulletin/Repair Instructions
IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the "Repair kit for button caps" when performing this repair. Replace ALL the buttons with those included in the kit. Note: Please do not use and claim the part number for the Repair kit, radio and A/C panel." To ensure the button cap kit with the correct symbols and labels is installed, perform a part number lookup in ETK by VIN. Labor operation code 64 11 326 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 64 11 769 instead."
651113
Service Bulletin/Repair Instructions
Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
120613
Service Bulletin/Repair Instructions
The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.
630513
Service Bulletin/Repair Instructions
FRM3 Will Not Communicate with ISTA. When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) "Display failure" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument cluster w/o light 2. Windows * One or both front windows INOP 3. LIN components https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15625.1.B630513... 8/29/2013 Page 2 of 2 * CCM "no blind spot detection" if equipped * Power mirrors INOP * Seat adjustment INOP 4. Hardware inputs * Door locks INOP * Gear shifts automatically to P * Gear shift lever cannot be moved out of P 5. Electrical steering column adjustment * ELSV (Electric Steering Column Adjustment) INOP CAUSE Various causes include the following: * Blown fuse * Faulty wiring * Faulty component
650813
Service Bulletin/Repair Instructions
? Bang & Olufsen Sound System: Loudspeaker Illumination. One or more of the following situations may occur concerning the illumination of the Bang & Olufsen sound system loudspeakers: * Illumination is insufficient (not bright enough) * Illumination is not available on all loudspeakers * Brightness cannot be adjusted Loudspeaker illumination settings are dependent on the model: * Different brightness characteristics * Not all loudspeakers are illuminated INFORMATION Explain to the customer that loudspeaker illumination can vary from model to model. For an overview of the illuminated loudspeakers, refer to the attachment. IMPORTANT: The current version of the Owner's Manual for 5 Series vehicles is incorrect. On 5 Series vehicles (F07 and F10), only the main loudspeaker (moving part) in the dashboard and the two loudspeakers in the mirror triangles in the front doors are illuminated. The Owner's Manuals for 5 Series vehicles will be corrected with start of production of the MY2014 vehicles (July 2013).
651913
Service Bulletin/Repair Instructions
HU-H: SDARS Radio Stations Cannot Be Stored in PRESET Menu. The SIRIUS/XM satellite radio (SDARS) stations cannot be stored in the PRESET menu. * No fault code related to this issue is stored in the HU-H. * AM/FM radio stations are not affected; they can be stored correctly. Software error in the SDARS control unit integrated in the Headunit-High (HU-H)
120412
Service Bulletin/Repair Instructions
N55: Idle Fluctuates Briefly After a Cold Engine Start. Under certain engine cold starts, the engine idle may fluctuate during the first 10-20 seconds of operation before becoming stable. No faults will be stored in this situation, which will usually only occur at specific engine temperatures, making it difficult to reproduce in the workshop. Unfavorable DME software calibration
320113
Service Bulletin/Repair Instructions
Squeaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
510813
Service Bulletin/Repair Instructions
Water Leaking into Trunk. Water leaks into the trunk on the left or right side. CAUSE The trunk lid hinge bracket fastener is not sealed to the body properly.
511113
Service Bulletin/Repair Instructions
Rattling Noise from Windshield Defroster Vents. Rattling noises can be heard from the instrument panel where the defroster vents are located.
611313
Service Bulletin/Repair Instructions
Service Action: Program Control Units (CAS). The Car Access System (CAS) was incorrectly coded with ISTA/P 2.49.2 or earlier, causing the anti-theft alarm system panic button on the remote control to stop functioning. AFFECTED VEHICLES This Service Action involves F12 vehicles which were produced from August 2010 to June 2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 648. If code number 648 has been punched out, the campaign has already been performed. If code number 648 has not been punched out, it will be necessary to utilize the "Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A Campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this Campaign reserved, please verify the reason before attempting to perform this repair.
511013
Service Bulletin/Repair Instructions
Center Console Makes Clicking Noises. The driver's or passenger's side of the center console may make a creaking noise when lateral force is applied, such as pressure from a leg or knee. CAUSE The center console side panel securing clips are rubbing against each other and/or on the center console support.
520413
Service Bulletin/Repair Instructions
Front Seat Has Side-to-Side Play and Can Make Noises When Cornering. 4.Remove the front seat outer cover panel by pulling the trim forward from the retaining clips. The front seat (driver or/and passenger) has play to the left and right, and can make noises when cornering. CAUSE The front seat base cushion shell is deformed at the cross tube of the tilt adjustment.
613812
Service Bulletin/Repair Instructions
Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the "Service Menu" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as "Pending" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair.
660313
Service Bulletin/Repair Instructions
Parking Assistant Inoperative After Programming. The parking assistant system does not function correctly. One or more of the following scenarios may occur: * Unable to activate the parking assistant via the iDrive * When activated, the vehicle does not locate a parking spot * Does not assist with parking the vehicle CAUSE Software error in ISTA/P 2.49.0 programming data
840513
Service Bulletin/Repair Instructions
TCB: Emergency Call Is Erroneously Triggered. An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control unit error
110113
Service Bulletin/Repair Instructions
MService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
120912
Service Bulletin/Repair Instructions
Intermittently, the engine idle speed may fluctuate up and down or cut off under any of the following circumstances, without any relevant faults stored in the DME memory: * While driving off throttle (coasting) and braking at speeds below approx. 10 mph * While idling, low-speed maneuvering such as parking, or if the steering is turned to the full-lock position Unfavorable DME software
330212
Service Bulletin/Repair Instructions
Rattling Noise from Rear Axle. A rattling noise is heard from the rear axle when driving over rough or uneven road surfaces. Internal tolerances of front and rear shocks
651313
Service Bulletin/Repair Instructions
Headunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. ??Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Hardware error in the Headunit-High
121611
Service Bulletin/Repair Instructions
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
520113
Service Bulletin/Repair Instructions
Front Crash-Active Headrest Has Limited Height Adjustment. INFORMATION This bulletin will help you understand the features of the crash-active headrest and explain the benefits to your customers and center staff. 1. Learn the safety features and operation of the front seat and crash-active headrest. Photos A and B: In the event of an accident, the rear passenger must be able to move the front seatback forward, regardless of the seat position. This allows the rear passenger an easy exit from the rear seat of the vehicle, even if the electrical power source is no longer available. 2. When the seatback is manually moved, the headrest must have free movement throughout the full range of the seatback. Photos C and D: The headrest and seatback must be able to move fore and aft without contacting the roof or sun visor, regardless of seat position. The headrest height will automatically adjust to maintain this clearance, regardless of seat position. 3. In case of an accident, the crash-active headrest will be automatically activated forward to reduce the distance between the occupant's head and the headrest. This results in increased safety for the occupant. Photo E shows the headrest in the normal position. Photo F shows the headrest in the "active" position and will not contact the roof. Note: The headrest's chrome bar supports can be seen.
610211
Service Bulletin/Repair Instructions
Advanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
840413
Service Bulletin/Repair Instructions
TCB: Emergency Call Is Disabled. A Check Control message shows "Emergency call failure." When the SOS button is pressed, the call is not made by the TCB (Telematics Communication Box). Fault code 0XB7F33F is stored in the TCB. CAUSE TCB application error
513012
Service Bulletin/Repair Instructions
Grating/Grinding Noise from the Center Console. A grating noise can be heard coming from the left front side of the front console trim panel, where it meets the instrument panel, especially when driving on rough roads. CAUSE Insufficient gap clearance between the console trim and the instrument panel.
620213
Service Bulletin/Repair Instructions
Instrument Cluster Only Displays Background Image and Gear Indicator. The display in the instrument cluster intermittently only shows the background image and the gear indicator. * No fault code is stored * All gauges function correctly Note: The issue is rectified after a sleep mode cycle (ignition off for approx. 16 minutes). Software error in the instrument cluster introduced with software I-level 12-03-500 or higher (ISTA/P 2.46.1 or higher)
620413
Service Bulletin/Repair Instructions
Head-Up Display: M View Defaults to Standard View. INFORMATION Do not replace any parts. Since this is part of the Head-Up Display concept change, it is normal operation after programming the vehicle with ISTA/P 2.47.1 or higher. ??From integration level: F010-12-07-531 or higher Note: It is not possible to change the functionality of the Head-Up Display to how it performed before the software update.
650713
Service Bulletin/Repair Instructions
HiFi Audio System: Audio Intermittently Cuts Out in All Audio Modes. Intermittently, the audio cuts out in all audio modes (e.g,. AM/FM radio, Satellite radio, CD/DVD, AUX-In, etc.) Application error in the HiFi amplifier
720113
Service Bulletin/Repair Instructions
Damage to Side Airbag Trim Mount on Front Seat. The side airbag trim mount on the left or right seat is separated (damaged). The damage occurred during a previous seat repair.
M520113
Service Bulletin/Repair Instructions
Front Seat Lumbar Support Not Working. The lumbar support does not function properly or at all for one or both front seats. CAUSE In most cases, the lumbar knob will rotate with limited or no movement of the lumbar support; this is due to a fractured or broken lumbar support.
621012
Service Bulletin/Repair Instructions
Head-Up Display Is Too Dark. The Head-up Display (HUD) is too dark. Rain/light/solar/condensation sensor (RLSB) hardware error
340112
Service Bulletin/Repair Instructions
Service Action: Replace Integrated Chassis Control Module (ICM). Due to a hardware fault in the ICM control module, an error code may be stored during engine start. If this condition were to occur, the airbag warning lamp would illuminate and be accompanied by a Check Control Message and acoustic warning.
512312
Service Bulletin/Repair Instructions
Front Door Window/Rear Side Window Reverses when Closing. When using the automatic window closing feature, intermittently the rear window automatically reverses. CAUSE Sensitivity of the anti-trap feature
652212
Service Bulletin/Repair Instructions
Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
130612
Service Bulletin/Repair Instructions
N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in "DME Diagnostic Query" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select "DME" in the control unit tree. 3. Select " Call Up ECU Functions." 4. Select "Diagnostic Query." 5. Select "Fuel Pressure (Low Pressure)." 6. Select "Query Status." The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.