B320526
Service Bulletin/Repair Instructions
“Cracking” noise might be heard when turning the steering wheel from lock to lock. See attached video V3202 26 EPS noise.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B320526
“Cracking” noise might be heard when turning the steering wheel from lock to lock. See attached video V3202 26 EPS noise.
B340124
After replacement of the Integrated Braking system (IB)/Power Brake the total distance covered might belower than when handed over to the workshop for the repair.
B630526
After programming the vehicle via ISTA/RSUto I-level …26-03-5xx, some of the interiorambient lighting strips (arrows) may begin tofail sporadically after a deep sleep cycle.
B652026
The Central Information Display (CID) side of the Multifunction Display (MFD) may flicker intermittently. Theflickering manifests itself in three phases: The image is distorted The central information display turns black (black screen) The image is OK again The complete flickering episode with all the above-mentioned three phases only lasts about half a second intotal each time.
B120326
Due to an implementation error in various OBD diagnostics in the vehicle's control units, in very rare cases itmay happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.
B310626
Noises from the front axle when driving over rough road surfaces, or when turning.
B310426
SITUATION When turning the steering wheel fully to the steering end stops, a ”groaning” noise can be perceived at the respective steering stop. The noise occurs at higher ambient temperatures from approx. 68°F.
B320326
“Groaning” noise from the EPS when the steering wheel is at the end stops.
B610226
In rare occasions, control of certain vehicle security functions via the Central Information Display (CID) is restricted for a short period of time.
B120526
A “knocking” sound from the fuel tank area can be heard in the passenger area. Occurrence information below. 1. The noise occurs when the engine is at idle 2. The noise occurs sporadically 3. The noise disappears when the fuel filler cap is opened 4. The noise also disappears when the tank ventilation valve is disconnected There is no relevant fault saved in the fault memory.
B310324
When rolling forward or backwards with the steering at full lock (left or right) without the brake applied, a “groan”-type noise may be heard from the front axle. The noise is most noticeable after load reversal. The noise can be heard beginning at the 7 second time stamp.
B060726
Wiring Harness Return
B060226
Tension Strut Return
B060126
Power Kit Electronics Return
B121125
One or both of the following faults stored in the DME: 034AA5 - Mixture control bank 1, lambda regulation, mixture too lean 034AA8 - Mixture control bank 1, lambda adaptation, mixture too rich And additionally with the faults above, these affected vehicles may have one or more of the followingirregular combustion-related faults also stored: 033812 033813 033814 033815 033816 033817 033818 033819
B120224
RSU availability. VOLUNTARY EMISSIONS RECALL 24E-A02: VALVETRONIC
B840625
In some situations, an emergency call may be triggered in the vehicle without either the customer pressing the SOS Call button, or an airbag deployment event. In some cases, the customer may not even be inside the vehicle.
B340825
Starting from I-level …24-07-500, it is possible that the Automatic Hold function is not automatically storedfor the next journey. The function must be activated again by the driver at the beginning of every trip. After asoftware update to 25-03-500 and higher, this occurs more frequently.
B320825
When the steering column is adjusted inwards towards the instrument cluster, the noise may occur near thelimit position.
B510324
While opening any of the doors, a groaning sound is heard from the door brake. Doors open and close stiffly.
B631023
Condensation is present in the inner surface in one or both (inner and/or outer) taillamps.
B110625
Due to an assembly error, the oil pump screws may not have been torqued correctly.
B064125
Seal Return
B063925
Adapter Disc Return
B610125
During highly dynamic driving, washer fluid may be forced out of the windshield washer nozzles. This canlead to the washer fluid reservoir being completely emptied.
B660325
Check control message is displayed indicating the parking assistance systems have limited functionality dueto errors detected within PDC sensors. The warning indicates parking assistance features have limitedfunctionality while the errors continue to be detected. Following faults may be stored 8031BA Ultrasonic Sensor Rear Side Left Software Error 8031CO Ultrasonic Sensor Rear outer left Software error 8031AE Ultrasonic Sensor Rear Outer Right Software Error 8031A8 Ultrasonic Sensor Rear Side Right Software Error 8031B4 Ultrasonic Sensor Rear Middle Right Software Error 8031C6 Ultrasonic Sensor Rear Middle Left Software Error
B410525
While attempting to fuel/charge the vehicle,the fuel/charge door will not open.
B063625
Hydrobearing Return
B520825
The rear seat leg rest can fold down when a heavy load/weight is placed on it.
B120425
EMISSIONS RECALL 25E-A02: PROGRAM CONTROL UNITS
B340425
As a result of a data input error, certain fault memories are permanently stored. The permanent storage offault memories does not comply with the legal specifications of the authority (California Air Resources Board– CARB). The fault has no effect on the use of the vehicle by the customer.
B660725
The speed limit warning adopted speed, which is set by the customer, is automatically reverting to lowervalue after an extended duration of the sleep cycle.
B120625
The electrical connector for the bank 1 high pressure pump may not have been locked correctly.
B651525
When initiating a phone call to a specific saved contact, Intelligent Personal Assistant may not be able tolocate the contact or may call the incorrect contact.
B110325
The “Check Engine Oil Level” warning is displayed while driving due to one of the following: Shortly after a detailed measurement has been carried out Shortly after engine oil has been topped up Shortly after an engine oil service has been carried out
B840225
When making phone calls via BMW Bluetooth (not Apple CarPlay) in the vehicle, the person in the calloutside the vehicle hears a distorted voice reproduction.
B650925
Customer may complain that Projected Modes (Apple CarPlay/Android Auto) do not connect in the vehicle. Itis found that the WiFi in the vehicle is also not active and cannot be turned on.
B320225
Parts of the steering shaft universal joint may have been joined together without having beengreased. As a result, there can be audible squeaking and cracking noises. In some cases, moresteering force is required.
B630418
One or more of the LED daytime running lights are dim or discolored.
B062125
LED Module Return
B620225
For certain model vehicles with the S68T engine, the Condition Based Service (CBS) data may show sparkplug replacement is due at a considerably “earlier” interval than specified in the Service and WarrantyInformational Booklet.
B060925
LED Upper Headlights Return
B510824
The Augmented Reality Camera (ARCAM) shows up blurry when activated.
B520225
The electric front seat adjustment does not work. The problem can occur to the left, as well as the right seat.
B514616
Upon opening and closing the tailgate, a creaking/groaning sound can be heard from tailgate actuator.
B120624
BMW AG has decided on a service campaign for certain vehicles from the G0x, G12 and G20 series. Please have the starter motor checked and, if necessary, replaced in the vehicles concerned (according to the vehicle identification number selection) if possible before vehicle delivery. If vehicles have already been delivered, please have the measure carried out the next time the vehicles enter the workshop. A bolting fault on the long bolt screws can cause the magnets in the starter motor to twist. As a result, the power of the starter motor decreases. As a result, the engine does not start.
B111024
The engine oil pump mounting screws may not have been tightened with the correct torque.
B350123
When the brake pedal is pressed/ released, a creaking noise may be heard from the pedal area for the Integrated Brake System (IB). This noise may be present with the vehicle stationary and the engine running.
B320125
Rumbling, groaning type noises from the EPS when the steering wheel is at the end stops.
B511924
There is a matte “veil” or milky stain on the exterior mirror glass.
B611124
After performing a BMW Remote Software Upgrade (RSU), the functionality of the Comfort Access and Passive Go/Exit features may be reduced.
B610124
When driving over rough surfaces, a low-frequency rattling noise can be heard inside the vehicle's cabin. The noise typically sounds as though it is coming from the front right footwell area.
B060125
SWIVEL JOINT RETURN
B653624
Customers may report issue with Personal eSIM operation, to include: Personal eSIM does not finish the set-up process in the vehicle Telephone function via eSIM is not possible WiFi Hotspot function cannot be used Streaming video service via the BMW Theater Screen is not possible
B653824
Customers may report issue with Personal eSIM operation, to include: Personal eSIM does not finish the set-up process in the vehicle Telephone function via eSIM is not possible WiFi Hotspot function cannot be used Streaming video service via the BMW Theater Screen is not possible
B840424
Customers may report issue with Personal eSIM operation, to include: Personal eSIM does not finish the set-up process in the vehicle Telephone function via eSIM is not possible WiFi Hotspot function cannot be used Streaming video service via the BMW Theatre Screen is not possible
B068324
Wastegate Valve Actuator Return
B110824
Delivery Stop Check PCV System
B160224
There may be a restriction in the low-pressure fuel line at the tank flange for the in-tank delivery pump (lowpressure pump). As a result, the required fuel flow volume is not available. If there is an insufficient supply offuel (even if only for a very brief period), the high-pressure pump might suffer preliminary damage. Inaddition, in the event of a fault, there might be a power reduction or “jerking” motions while driving.
B410824
DELIVERY STOP: REAR BUMPER BRACKET
B512724
The Ethernet bus of the Body Domain Controller (BDC) is interrupted so that audio output, rear viewcamera, or the driver assistance systems fail. The symptoms begin to appear during auto locking at approx.10 mph, or after the Central Locking button is activated. Dependent upon vehicle equipment, the following permanent SAE faults may be stored in the vehicle: S 0219, No Communication possible with: Amplifier S 0261, No Communication possible with: Camera-based driver assistance S 0273, No Communication possible with: Headunit S 0313, No Communication possible with: All-round vision camera S 0386, No Communication possible with: Instrument Panel S 0394, No Communication possible with: Telematics control unit
B067924
Air Suspension Strut Return
B340324
Improved diagnostic software for the brake system.
B612424
Small debris may accumulate inside the volume control thumbwheel of the iDrive Controller. Existing gaps between the glass application and the light guide could allow external debris to enter inside the volume thumbwheel under normal usage. This debris can be seen through the crystal volume thumbwheel, giving the appearance of a cosmetic defect with the thumbwheel itself. Active lighting makes this debris more visible when illuminated. This could make the false illusion of a cosmetically defective volume thumbwheel more visible (many small dark spots or streaks).
B651423
BMW Theatre Screen (SA6FR) with connected Amazon Fire TV stick turns black at low speeds and during maneuvering.
B612324
A failed or insufficient grounding system can lead to wiring and component failures, reduced efficiency, anddowntime. To help avoid these risks, it is essential to ensure system integrity by following repair instructionsand properly torquing all connection points. Proper grounding and bonding complete the electrical circuit andprovides a safe way for excess electricity to dissipate.
B110324
Delivery Stop - Oil Pressure Sensor
B611724
DELIVERY STOP: PROGRAM DOOR MODULE CONTROL UNIT
B660424
The washer fluid cleaning system has air remaining in its components, and/or the fluid lines after a previous repair has been performed. The previous repair may have involved draining, opening, and replacingcomponents in the system.
B370124
While driving at low speeds (15-40 mph) on flat road surfaces, a knocking noise from the front axle may beheard during steering wheel movements.
B270220
There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages.
B120424
Customer perceptions: Vehicles with optional equipment “01CR -Remote Engine Start”. The “Remote Engine Start” selection is missing in the “Pre-conditioning” sub-menu The “Remote Engine Start” can be selected using the vehicle key. However, the “Remote Engine Start” isnot carried out. The Check Control message (number 2055) appears: Remote engine start not available Vehicles with optional equipment “07ME - M Driver’s Package”: The increased maximum speed is not reached Vehicles with optional equipment “01MB - M Drive Professional”: The M MODE “TRACK” is no longer available Only the M MODES “ROAD” and “SPORT” are available Applies to all the customer perceptions: Chance of the error occurring: Very rare, sporadic Both faults listed below are entered in the DME fault memory: 021280 - DME: Certificates (type 1) not ready And 021283 - DME, Secure Feature Activation: Secure Token check still running or unchecked Secure Token present Motor vehicles affected: Vehicles with engine S68T Vehicles with drive unit XB1T
B650121
No Bass or a cracking noise can be heard from the bass speakers.
B652023
The Service Acti on related to SIB 65 20 23 has been completed and the defect code has been closed by warranty. Alllisted VINs have had the acti on performed. This Service Acti on is complete and the informati on is no longer valid
B651424
Intermittently the iDrive Controller may stop functioning. This applies to the iDrive Controller knob and alsothe iDrive Controller function buttons (NAV, MEDIA, TEL, etc.). The touch functions on the Multifunction Display and voice interactions through the Intelligent PersonalAssistant will still function normally.
B520424
The following fault memory entries in the BCP_01 are displayed in the vehicle’s fault memory withoutjustification: 804344 – Control electronics, front active seat ventilation, driver's seat cushion (LIN):Communication fault detected 804345 – Control electronics, front active seat ventilation, seat cushion of front passenger (LIN):Communication fault detected
B651224
The Central information Display (CID) screen goes black and the Headunit (HU-H3) resets sporadically.After a short period of time, the function of the CID and HU-H3 is available again. Additionally, fault code B7F8F9 – “HU-H: Reset” will be stored in the HU-H3. The issue may occur multiple times while driving longer distances. CAUSE Unfavorable
B651324
The Owner’s Manual in certain vehicles has been released with incorrect data regarding Vehicle Gross Mass, Approved Front Axle Weight, and Approved Rear Axle Weight. In very rare cases, this could lead to a customer unknowingly overloading their vehicle.
B651024
Quality improvements and robustness measures are to be implemented on the affected vehicles via thissoftware update. The software update improves functions in the following areas of the vehicle: Bluetooth malfunctions The start-up phase of the head unit (HU) has been shortened (faster start of the operating system) The number of disconnections from Apple CarPlay have been reduced Vehicle access and the drive-ready state have been improved The AC charging abort error has been fixed Remote Control Parking without function
B064224
Bag Mobility Set Return
B064124
Alloy Wheel Return
B650724
In vehicles that are not mapped to a BMW ID, the manual time setting option is not selectable (greyed-out)in the System Settings menu. Time cannot be manually set in the vehicle.
B064024
Steering Wheel Module Return
B360121
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned.
B120224B
BMW AG has issued a Delivery Stop (effective April 12, 2024) on certain Model Year 2023 - 2025 BMW vehicles that were produced between July 21, 2021, and April 11, 2024.
B120224A
BMW AG has issued a Delivery Stop (effective April 12, 2024) on certain Model Year 2023 - 2025 BMW vehicles that were produced between July 21, 2021, and April 11, 2024.
B630523
The connection between the LED module and the light tube inside the upper/top headlamp housing is damaged.
B640524
When the interior temperature of the vehicle is between 5 F (-15 C) and 23 F (-5 ), the defroster function is limited; and the interior doesnâÃÂÃÂt heat up quickly enough.
B612723
The original Conditioned Based Service (CBS) Key data point closed with 23-07 soft ware, all CBS systems are now collectively under analysis.
B640424
1. The center air vent on the left (a) is closed. All other air vents on the left side then only blow cold air intothe passenger area. OR 2. Both center (b) air vents are closed. All other air vents then only blow cold air into the passenger area. OR 3. The center air vent on the right (c) is closed. All other air vents on the right side then only blow cold airinto the passenger area.
B110723
The return springs on the exhaust camshaft followers may break.
B310224
A knocking, âÃÂÃÂthumpâÃÂÃÂ-type noise may be heard from the front axle during straight-ahead driving on uneven road surfaces at low speed, e.g., below 40 mph.
B660324
A quality check showed that the Remote-Control Parking token was not activated in the current software for the vehicles affected.
B510819
The basic conditions for initializing the power windows are not met.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B510124
The side cover cap on the sunblind can unclip. As a result, the sunblind is no longer guided on the rail.
B160123
A vehicle arrives at your center to be diagnosed for a micro-leak in the fuel evaporative (EVAP) system(NVLD natural vacuum leak detection). For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5mm For: Model vehicles other that the ones listed above, or for EVAP faults related to a âÃÂÃÂlarge leak,âÃÂàafter confirming that the fuel filler cap is fitted properly, then, proceed to follow the corresponding test plan
B654123
Quality improvements and robustness measures are to be implemented on the affected vehicles via thissoftware update. The software update improves functions in the following areas of the head unit: 1. Bluetooth connection issues and Bluetooth malfunctions (disconnections) 2. Central display may remain black in rare cases 3. Personalization issues and the loss of normalization/sitting position 4. Missing Condition-Based Service (CBS) data
B160623
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
B511723
While driving at highway speeds, wind noise can be heard from the exterior mirror assembly. In some cases, this can be also feltin the B-pillar area.
B653423
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
B661523
Emergency Stop Assistant is activated. Thisicon will appear in the CID when this function is activated.
B612823
A thumping sound is heard when the window reaches the closing end stop.
B631323
The carpet welcome light(s) turns on either after a delay, or does not function at all.
B631123
Moisture is visible in one or both of the Daytime Running Light (DRL) headlights.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.