Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B840616
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT: BMW Online/BMW ConnectedDrive not functional.
B650414
AIRBAG WARNING LIGHT: ACSM FC 930A60 OR 930A1C SEAT OCCUPANCY DETECTION. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault (moisture)" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself.
B661017
BUZZING NOISE HEARD COMING FROM STEERING WHEEL. While driving at highway speeds, on uneven road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system
B520417
BACKREST NOISES WHEN UNDER LOAD. Pop noise coming from seat backrest when pressure exerted toward rear or while pulling away from a stop. Friction between top right rivet holding lordosis (back Lumbar support) valve block and backrest cushion spring.
B110815
N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin replaces SI B11 08 15 June May 2017 What's New: Diagnostic tips updated. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon.
B840214
ConnectedDrive/BMW Assist System Diagnosis Information This Service Information bulletin replaces SI B84 02 14 dated July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
SIM010717
The engine?s intake charge-air duct limited warranty extension to 10 years/120,000 miles applies to ?eligible USspecification
SIM010917
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
B130315
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B650717
LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."
B840311
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B111115
?SERVICE ACTION: REPLACE THE THERMOSTAT What's New: ? Part number and quantity of coolant has been updated. Refer to the Warranty section for details. . The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
B111216
?SERVICE ACTION: SERVICE ACTION: N63T ENGINE CHECK AND REPLACE THE CRANKCASE VENTILATION HOSES What's New: ? Defect Code format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
B650616
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B111715
?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 "Removing and installing/replacing upper oil sump" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. "All threads must be cleaned with screw tap" Or "Clean all threads with screw tap. Order number 81 43 0 402 559" Or "Clean all threads with a thread cutter". The current repair instruction terminology will be modified to include this information.
B180117
? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message "Drive faulty" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF.
B180310
? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The 10146535 20181105 B180310 20170201 Service Bulletin/Repair Instructions BMW 750LI 2012 ENGINE ? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B160715
Fuel Tank Non-Return Valve Faults with SES Light. Check Engine Light is illuminated and the following faults are stored in the DME: 0x191A94 - Fuel tank non-return valve: clamped shut 0x191A93 - Fuel tank non-return valve: clamped open CAUSE Software and hardware errors.
B650915
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
B070314
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B630516
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by "condensation" rather than a "water leak" into the headlight housing, there will be misting/condensation in "both headlights."
B652616
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B340516
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652316
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B652416
NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes "without a cash option" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes "without cash option". UPDATE Install new map data.
B652516
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B662116
KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B310112
CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
B661616
BUZZING NOISE HEARD COMING FROM STEERING WHEEL. While driving at highway speeds, on older (worn) road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system
B511615
Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2
B513016
TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
B661816
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B330416
Delivery Stop: Replace Rear Differential.
B520412
Front Seat Base Makes Noise. A noise may be heard from the left or right front seat base when driving on rough roads. CAUSE The riveting of the seat control bracket to the metal seat base is too loose.
B621015
Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 "display backlighting and graphics PCB switched off" stored. Kombi software.
B111615
?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
B240712
This Service Information bulletin supersedes SI B24 07 12 dated November 2012 SUBJECT Hybrid Automatic Transmission: Fluid Maintenance Service Interval. INFORMATION Only properly trained personnel, who have passed all applicable technical training courses, should perform any maintenance or repairs on any Hybrid or Electric Vehicle. Work performed by unqualified persons may result in severe injury or damage to the vehicle. Additional information may be found in REP 61 00... Observe safety instructions when handling electric vehicles. This requirement is due to the hybrid-specific components that are contained in the transmission. Refer to Repair Instruction 00 00 630, "Automatic transmission fluid service (GA8P70Z) N55 hybrid," for the proper servicing procedure. Refer to SI B00 09 12 for BMW Maintenance Program claim-related information.
B270415
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B340414
Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
B111012
N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
B111315
The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
B130215
?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail.
B330115
Cracking in Rear Differential Mount Bushing. During inspection, the rear differential mount in the rear axle support shows signs of cracking.
B651015
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B121915
Service Action: Replace EME B+ Cable. The Electric Machine Electronics (EME) has a connection for the B+ cable which leads to the 12V battery. This B+ cable transfers energy from the DC/DC converter to the 12V network. This cable may corrode over time and, in extreme cases, could break. In the event of a cable break, output from the DC/DC converter would be interrupted. This interruption would cause the 12V battery to discharge. Subsequently the customer would be notified via a check control message that the 12V battery is discharging, and the vehicle may not restart after being switched off.
B611415
SME Fault Code: CAD400. ? The customer states that check control message (CCM) "Drive faulty" Electric driving is not possible" is intermittently displayed in the instrument cluster, and: ? Fault code "CAD400 - No message (status E-motor 1, 0x10F), receiver SME, transmitter EME" is stored in the battery management electronics (SME). CAUSE Electrical Machine Electronics (EME) software error
B613014
BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is "applicable" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
B111614
This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard.
B610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
B110315
N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
B110515
N20 and N55 Engine: Engine Oil Filter Application for Plastic Oil Filter Housing. The current version of EPC does not provide all available options for the engine oil filters used in the N20 and N55 engines produced with a "plastic" oil filter housing. The illustration below will help identify the proper engine oil filter application until the EPC is corrected.
B110715
N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled "N63: Drivability after CCP." Follow the recommendations received.
B121415
DME Fault Code CD9711 Stored After Programming. After programming the vehicle with ISTA/P 3.55.0 (I-Level F010-15-03-501 and F001-15-03-501): ? The check engine light (CEL) is illuminated, and ? DME fault code "CD9711 - FlexRay, message (control diagnostics OBD vehicle dynamics, 247.0.2): missing" is stored and cannot be cleared. CAUSE DME software
B340215
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Program Control Units (DSC). In very rare driving situations (distances of more than 310 miles travelled without any DSC, ABS or cruise control/ACC regulation), the DSC return pump is activated in order to initiate internal flushing. When this occurs, it is possible that the pump is not switched off until the engine is turned off. VEHICLES AFFECTED This Service Action involves certain ActiveHybrid models produced from 8/6/2013 to 1/27/2015. First check if a Service Action label with a code number 739 is already attached to the B-pillar. If a code number 739 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
B840514
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
111614
This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard.
270213
SI B27 02 13February 2015 Intermediate and Special Transmission Technical Service This Service Information bulletin supersedes SI B27 02 13 dated June 2013. designates changes to this revision SUBJECT Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
110215
SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)
110614
This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: z Hot-Film Air Mass Sensors z PIEZO High Pressure Fuel Injectors z Engine Vacuum Pump z Fuel System Low Pressure Sensor/Feed Line z Fresh Air Intake Turbo Seals z Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying "time-based" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see "Warranty Information" section below).
120115
SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
120415
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
120915
SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the "fuel consumption, current" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold.
123814
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
340714
SUBJECT Carbon Ceramic Brake Noise. INFORMATION "M" vehicles are designed for high-performance, spirited driving. To accommodate this type of driving profile, a braking system which exceeds the standards for handling heavy brake forces, extreme temperatures, and excellent stopping power at high speeds is required. "M" vehicles can be ordered with the optional ultra high-performance braking system, featuring perforated carbon ceramic brake discs designed for circumstances similar to those encountered on racetracks. The carbon ceramic brakes were designed to improve braking efficiency, and dramatically increase braking performance along with a significant reduction in weight. When developing the carbon ceramic brake system, the main focus was on braking performance for the sporty-minded driver, while accepting the comfort limitations of functional noises at slower speeds and when coming to a stop. Please inform the customer that the carbon ceramic brake system's functional noises (squealing/honking), are a known characteristic for this type of material, and are only a small trade-off for the improved braking performance. These functional noises have no effect on the performance, operational reliability and durability of the brakes. Part replacement will not provide a remedy for the noise; this is a known characteristic of the high-performance brake system. More information on the performance and operation of these brakes can be found in the Owner's Manual under "M carbon ceramic brake." WARRANTY INFORMATION Not applicable.
650509
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
651312
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
652413
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
840115
MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received.
110713
The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
122114
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated and, while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Vehicles with option 610 (Head-Up Display) are not affected. Follow the ISTA/D test plan for the applicable faults stored in the DME. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling.
130712
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
161514
NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
340414
Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
340514
Dynamic Stability Control Unit (DSC) Aborted when Programming Vehicle. If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software
652214
Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.
513314
This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
011314
BMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
010414
External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
650214
Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
652113
When Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
660414
Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
840214
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
360314
RDC: Incorrect Tire Position Displayed with Air Pressure Drop. When there is a low tire pressure warning, in some cases the position of the affected tire may be incorrectly displayed in the instrument cluster and CD (Control Display). Software error in the RDC (tire pressure control) module in conjunction with wheel electronics part number 4 078 787 or 4 079 152.
840314
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
310112
Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
320114
Service Action: Replace Power Steering Pump Belt Pulley. The screw connection on the power steering pump belt pulley may slacken. This may lead to an audible squeaking and rattling at the pulley drive. AFFECTED VEHICLES This Service Action involves 5 Series 535d vehicles according to VIN selection. First check if a Service Action label with a code number 682 is already attached to the B-pillar. If a code number 682 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
340213
Incorrect Remaining Service Life from CBS Data for Brake Pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.
620613
Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
121513
?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
630414
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
840913
My BMW Remote iPhone App No Longer Controls Headlight or Horn. After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.