Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
MC000521
One of the following situations can occur when connecting to BN2000 motorcycles: 1. The installed control units cannot be found when reading out with ISTA. 2. Control units initially communicate after connecting to the vehicle, but communication later stops.
MC210221
The clutch plates do not tolerate frequent and prolonged operation at the clutch friction zone, causing a shorter service life in motorcycles that see intensive use
MC460421
The customer complains about metallic rattling noises from the area of the chain guard on the footrest plate
B110113
N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
B011218
?N63T CRANKCASE VENTILATION LINES: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILEAGE. For the eligible vehicles, BMW of North America, LLC (?BMW NA?) is extending the limited warranty for the engine Crankcase Ventilation Lines to: 10 years/120,000 miles as determined by the vehicle?s original in-service date Note: This bulletin is notice of a ?limited warranty extension.? This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter Even though this is NOT a Recall, BMW NA sent VIN-specific customer notification letters in a phased release.
B111117
?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B840214
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.
B110618
TURBO BOOST ACTUATOR ROD LOOSE (DIESEL): Limited engine performance (lack of boost) with a Malfunction Indicator Lamp (MIL) illuminated.
B520318
MEMORY SEAT ADJUSTMENT IS LIMITED: After programming the vehicle with ISTA 4.10.2x, the adjustment range of the memory seat may restricted.
B650709
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B610818
SME FCS 21F156 21F1F7: The following codes are saved in the battery management electronics (SME) fault memory:
B840616
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT: BMW Online/BMW ConnectedDrive not functional.
B310112
CRACKING NOISES FROM THE FRONT AXLE AREA WHILE TURNING THE WHEELS, WHEN STATIONARY OR PARKING
B513016
TAILGATE UNINTENTIONALLY OPENS: Trunk/tailgate may open when vehicle is locked.
B110115
Engine Oil Quick Reference Chart and Drain Plug Torque: The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive.
B841117
BMW APPS RANDOMLY STARTS PLAYING ON ITS OWN: While listening to FM, or AM, or Satellite Radio (SDARs), the audio source randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.
MC64010520
Incorrect tire pressure appears in the instrument cluster. Contamination or obstruction of the RDC sensor.
B650915
NBT Head Unit High (HU-H) Resets Intermittently or Permanently
B660814
Side View Camera Does Not Display Picture.
B650414
AIRBAG WARNING LIGHT: ACSM FC 930A60 OR 930A1C SEAT OCCUPANCY DETECTION. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault (moisture)" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself.
MC2300117
Customer complains about an operating failure on the left or right multifunction switch.
MC63308496
Frequent failure of the gear indicator and engine running issues after changing the final drive ratio (drive chain and sprockets) on K7X bikes with electronic throttle control.
B130315
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B613014
?BMW Maintenance Program: 12-Volt Battery Replacement Measure What's new: ? Models" updated: Model Year 2017 vehicles added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
B840311
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B111216
?SERVICE ACTION: SERVICE ACTION: N63T ENGINE CHECK AND REPLACE THE CRANKCASE VENTILATION HOSES What's New: ? Defect Code format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
B620317
?SERVICE ACTION: INSTRUMENT CLUSTER DISPLAY IN KM/H . When the instrument cluster's digital speedometer has been set to display metric speed and distance values, there is no display of the miles per hour. US regulations specify that even with the instruments set to display metric values, a "Miles per hour" display must also be present for immediate visual reference. To confirm language settings use the iDrive controller: Menu, Vehicle Settings, Language/Units, then - Distance - Dig (digital) Speedometer Instrument Cluster (KOMBI) software error.
B650616
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B340516
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652016
CID Split Screen Always Changes Back to Compass Display. This Service Information bulletin Replaces SI B65 20 16 dated June 2016. After starting the vehicle, the Control Display (CID) right side (split screen) display does not stay on the last selection made by the driver. Within 30 seconds of starting the right side of the display changes by itself to the compass view. Software error (Head Unit NBT-EVO ID5) was introduced with ISTA/P V3.58.0 (16-03-502 I Level).
B661616
BUZZING NOISE HEARD COMING FROM STEERING WHEEL. While driving at highway speeds, on older (worn) road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system
B011316
BMW ALPINA N63T PRESSURE SWITCH - LEAK DIAGNOSIS MODULE (NVLD): LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES. INFORMATION For the above-referenced vehicles, BMW of North America, LLC ("BMW NA") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Note: This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release.
B330416
Delivery Stop: Replace Rear Differential.
B320616
Troubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
MC1100116
Coolant pump drain hose. Details The coolant pump is fitted with a radial shaft seal on the oil-side and on the coolant-side is a mechanical seal. Mechanical seals are reliable an durable, yet for technical reasons, they always exhibit minor seepage. The seepage amount is considered to be within permissible limits if the coolant does not need to be topped up between service intervals. The drain hole (arrow in the figure) of the coolant pump is in plain view. Even small, inevitable seepage is noticed and often perceived to be a faulty coolant pump. In many such cases, fault-free coolant pumps are replaced. In order to reduce misdiagnosis and repeat repairs, a drain hose is retrofitted. The hose diverts the seepage away from the field of view to under the engine. Yet large amounts of leakage that indicate a faulty coolant pump will be noticed.
MC35742107
Loss of coolant from expansion tank. Coolant escapesfrom the expansion tank. Construction design of the expansion tank and breather cap.
B840715
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
MC59759165
Transmission rattles when the engine is at operating temperature and idling.
B620715
Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
MC61461571
Mist forms in the headlight. This is due to condensation and goes away again.
B660115
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B840514
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
122114
SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
651009
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
840115
MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received.
110713
The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015
161514
NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
513314
This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
651614
Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID Affected Central Information Displays were manufactured from 02/01/2013 to 06/09/2014. The manufacturing date is included in the serial number printed on the parts label on the CID. IMPORTANT: The manufacturing date is written in the following way: dd mm yy Example: The manufacturing date of August 15, 2013 is printed on the label in the following way: 15 08 13
631114
LED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
651313
Headunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
660814
Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
8403014
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
MC55813536
Navigator V maintains a Bluetooth connection to a mobile phone for a short period.
MC56005564
Heated handlebar grips intermittently not working
511514
Service Action: Replace Center Console Lock Cylinder. The center console lock cylinder is loose. Manufacturing tolerances of the center console lock cover cap may cause it to become loose or missing. AFFECTED VEHICLES This Service Action involves F01, F02, F06, F07, F12 and F13 vehicles produced from March 7, 2014 to April 23, 2014. First check if a Service Action label with a code number 688 is already attached to the B-pillar. If a code number 688 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
650214
Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
652113
When Unlocking with Comfort Access the Outside Door Mirrors Are in the Wrong Position. The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module
660414
Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.
660614
Rear View Camera Does Not Display Image on CID. After engaging the reverse gear, the reversing camera does not display a picture in the CID (Central Information Display). CAUSE The drive mechanism for the roundel actuation in the boot lid is faulty.
840214
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
840314
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
620613
Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
653009
Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.