Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B340714
Functional noises (squealing/honking) when braking shortly before the vehicle comes to a stop. CAUSE Material-
B662419
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B610322
The footwell module (FRM) cannot be encoded after replacement.
B340414
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B110208
Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
B130619
SERVICE ACTION: N54T ENGINE - INSPECT AND REPLACE INJECTOR(S). The piezo-type fuel injectors may cause a rough running at start-up or rough running while at idle.
651512
Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
513608
Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
513911
Trunk Lid Intermittently Does Not Open or Latch. Intermittently the trunk lid does not pop open when using the remote, or latch when closing. If the vehicle is driven and the trunk is not closed fully, a Check Control message will be displayed in the instrument cluster. CAUSE: The trunk lid is out of tolerance. When opening or closing the trunk lid, the latch rubs against the striker because of insufficient clearance.
610405
Power Mirrors and/or Windows are Inoperative. The power windows and/or power mirrors are inoperative. The LED on the headlight switch is flashing. There is a check control message for Windows/Mirrors/ Headlights. There may also be a complaint of water in one or both headlights. One of the following fault codes may be stored: * 9CBD - Communication with stepper motor box left defective * 9CBE - Communication with stepper motor box right defective * 9CC1 - Communication with mirror driver side defective * 9CC2 - Communication with mirror passenger side defective/Right Stepper Motor Controller (SMC) signaling fault * 9CCF - Communication with LIN control defective Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector. CAUSE: Left and/or right headlight housing cover is not properly fitted allowing water ingress into the Stepper Motor Controller (SMC) connector.
613312
Erroneous CC Message Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"
121412
N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
B540907
RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. This Service Information bulletin replaces SI B54 09 07 dated September 2018.
B013118
TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
B011618
TAKATA CLASS ACTION SETTLEMENT. CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.
B840214
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: ConnectedDrive/BMW Assist features are partially or completely inoperative.
B650709
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B080119
In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
B840314
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B612616
Interrupted supply of power to the vehicle. ? Initial vehicle entry / engine ignition may not function. ? Intermittent power failure during a journey may cause:o Instrument cluster flickering o Engine jerking. Plug-in contact of the positive battery cable, located at the front power distribution box has been damaged. ? Vehicle vibrations and frictional corrosion can cause a high current flow thru the wire. ? The excessive current draw causes damage to the battery positive cable plug contact.
B130315
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B840311
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B840316
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B180117
? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message "Drive faulty" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF.
B180310
? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The 10146535 20181105 B180310 20170201 Service Bulletin/Repair Instructions BMW 750LI 2014 ENGINE ? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B070314
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B652616
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B652516
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B270216
REPAIRING TRANSFER CASE ACTUATOR (VTG SERVO-MOTOR). The Anti-lock Brakes (ABS), Brakes and Dynamic Stability Control (DSC) warnings are on and there may also be a "Drivetrain Malfunction" warning on in the Control Display. There is also an audible clicking noise coming from the transfer case actuator when cycling the ignition. The following fault codes may be stored: (DSC) 5F3A - Clutch gearbox-ECU: clutch is open - rear-wheel drive! (VTG) 5463 - Break mechanics (VTG) 5462 - Error actuator or increased power requirements for clutch (VTG) 5461 - Error actuator control Internal wear to the plastic gears of the transfer case actuator.
B121116
ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
B122110
N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
B650216
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B090615
New programming feature: Exclusion of Infotainment Control Units from Programming. Programming with ISTA/P 3.57.4, or a more recent update, displays a new Pop-Up window providing options for systems programming.
B652606
The Disclaimer screen automatically disappears from the CID after 10 seconds. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/28...12/2/2015 Page 2 of 2 An enhancement was made to the Car Communication Computer (CCC) and MASK (Multi Audio System Controller) in 2006 so the customer does not have to manually accept the "Disclaimer" screen each time. Older vehicles prior to the production dates listed above that are programmed with ISTA/P 2.52 or higher will also get this enhancement. WARRANTY INFORMATION Not applicable.
B270415
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B640315
Air Conditioning Cooling is Insufficient or Inoperative. The air conditioner system refrigerant level is low or empty. CAUSE The evaporator is leaking refrigerant.
B650215
iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
B360215
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
070314
This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
650215
SiDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion
120415
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
650509
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
340414
Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
840412
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
SIB-34-04-14
BMW: RUNNING NOISES HEARD WHEN BRAKES ARE APPLIED, WITH HIGH BRAKE LOADS; THROUGH WHEEL OPENING, VISIBLE CRACKS CAN BE SEEN IN BRAKE DISCS AND STEERING WHEEL TORSIONAL VIBRATES WHEN APPLYING BRAKES. *PE
011214
M57 Diesel Engine Throttle Valve (for EGR): Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the M57 diesel engine's throttle valve (for EGR) on the above-referenced vehicle to: 10 years/120,000 miles, whichever occurs first, as determined from the original in-service date. This bulletin is a notice of a "limited warranty extension." This is not a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA sent VIN-specific customer notification letters. A sample letter is attached. Eligible BMW Vehicles To assist you in identifying eligible vehicles, the DCSnet Warranty Vehicle Inquiry has been updated with the following "Vehicle Comment," shown below: BMW of North America, LLC has extended this vehicle's M57 diesel engine throttle valve (for EGR) limited warranty to 10 years or 120,000 miles, whichever occurs first, as determined from the original in-service date. Please see SI B01 12 14. Note: Always check the DCSnet Warranty Vehicle Inquiry "Vehicle Comments" and the "Repair History (Claims)" sections first before performing any repairs.
111414
Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
122110
N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
280114
DCT Transmission: Oil Leakage Diagnosis. INFORMATION Incorrect diagnosis of DCT (Double-clutch Transmission) oil leaks may lead to unnecessary part replacements and repeat customer repair visits. When diagnosing complaints related to DCT fluid leaks, please use the attached diagnostic procedure. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B280114_DCT_Oil_Leak_Diagnosis. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16672.2.B28011... 12/24/2014
8403014
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
010914
?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho 10148018 20181113 010914 20140901 Service Bulletin/Repair Instructions BMW 530XI 2006 AIR BAGS ?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
611714
Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is "aged." When energy diagnosis identifies the battery as "aged," it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, "07 Battery Basics."
310109
Creaking or Groaning Noise During Compression and/or Rebound of Front Axle. A grating or groaning noise is heard when the front axle compresses and/or rebounds. This may be heard particularly over speed bump-type surfaces. The noise normally occurs at lower outside temperatures. The noise may be less prevalent when the vehicle has been driven up to the operating temperature.
650511
Previously assigned radio channels to the satellite radio "Presets" list have been erased and radio channels selected from the list "All channels" menu cannot be stored in the "Presets" list. The problem occurred after the recently implemented Sirius/XM channel lineup change. The data handling between the satellite radio receiver (SDARS-Exbox) and the Car Communication Computer (CCC head unit) has been corrupted.
610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
840214
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
840314
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
340313
Incorrect Remaining Service Life from CBS Data for Brake pads. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
360309
Third Generation Tire Pressure Monitor System (RDC). INFORMATION As of September 2009 production, a new generation Tire Pressure Monitor System has been introduced for all 3 Series models. Although the basic operation of the system is similar to the previous version, there are several key differences between the two systems. The new system consists of five components: One central antennae with an integrated control module (5) mounted in the right rear wheel arch Four wheel electronics (1-4) mounted at the base of each tire valve. Central antennae with integrated control module The control module and central antennae have been combined in a single housing. This new control module has the ability to send requests for information to each of the 4 wheel New style wheel electronics The wheel electronics consist of a plastic housing with integrated circuitry. The following items are contained within the wheel electronics: Pressure sensor Temperature sensor Acceleration sensor Transmitter/receiver unit Self-diagnosis controller Battery The following points should be considered when diagnosing and/or servicing the system: * The system components are not interchangeable or compatible with previous versions. * The type of wheel electronic fitted can only be determined via visual inspection. * The detection of low tire pressure and the subsequent warning is similar to the previous design. * The reset procedure has changed. Special Note for Reset Procedure After initiating a reset, the vehicle must be driven for a period longer than 12 minutes with a vehicle speed which exceeds 19 mph (~30 km/h). WARRANTY INFORMATION Not applicable.
540908
Cleaning Excess Butyl from RHT Roof Shells. Butyl adhesive is used to secure the seals of the retractable hardtop (RHT) to the steel roof shell panels. Particularly at high ambient temperatures, if excess butyl is present, it may start to seep out from between the seal and the roof shell. This butyl may be black or gray in color. Excess butyl applied to the roof shell during assembly
630714
One or Both Xenon Headlights Aiming Downwards. CAUSE Both sides are aiming downwards: * The most likely cause is a faulty or disconnected rear height sensor. In very extreme cases due to poor road conditions, both headlight assemblies could have the vertical aim ball socket adjuster disconnected, as noted below. Only one side is aiming downwards: * The cause could be a "disconnected" vertical aim ball socket adjuster, resulting from excessive road vibration or sharp impacts (pot holes) through the suspension to the headlight assembly. Important Note: Follow the procedure outlined in this bulletin first; replacing headlight assemblies for a vertical aim ball socket adjuster issue is an excessive repair.
650514
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
650314
RAD2+ Radio: Background Noise with Audio Turned Off. Background noise (buzzing, crackling, static) can be heard: * At low audio volume * When the radio is turned off * When the ignition is turned off NOTE: Background noise stops when the radio enters sleep mode. IMPORTANT: Background noise is more noticeable on vehicles produced before 09/2009 in case a RAD2+ replacement radio was installed previously. RAD2+ radio concept, manufactured from July 2009 to February 2014
840114
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
240413
GM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
510807
Erroneous Trunk Lid Open Check Control Message. The trunk open check control message may appear, even though the trunk lid or tailgate is fully closed and latched. CAUSE Incorrect adjustment of the trunk latch striker
612906
ELV Does Not Release. Cause 1: The steering column is held against the steering lock because of torque from the steering gear. In such cases, a yellow check control warning (CC ID# 187) is shown in the instrument cluster, but no faults are stored. Cause 2: Communication fault in the CAS (Car Access System) and ELV system network and/or battery low. The problem may cause the ELV warning to be displayed in yellow or red.
630414
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
652513
ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST "My Info" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
651013
The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, "Replacing sensor mat (OC3 mat) for passenger seat occupancy detector." 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding.
651112
Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
010212
BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the "Vehicle Comment" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage.
511907
Doors Will Not Unlock Using the Key Fob or Central Locking Button. One or more of the doors may not unlock when using the remote key outside the vehicle, or the central locking button inside the car. It is still possible, however, to unlock the door by using the key in the driver's door lock cylinder or by pulling the door handle on the inside of the car. Typically fault codes A6D4 and A6D5 are stored in the Junction Box Electronics (JBE). This is due to a blown fuse in the JBE caused by either: * An excessive amperage draw by one of the door lock actuators, which is commonly attributed to silicone contamination; or * An intermittent, but acceptable, amperage spike slightly above 15A, due to normal variation in the locking system.
130409
N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked ("wet") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the "N54 Engine Diagnostic Fault Tree" file (the current version "02_14_13" is found as a PDF attachment to SI B12 55 06).
340208
Erroneous Brake Pad Replacement Message. The Dynamic Stability Control module (DSC) calculates the brake pad replacement intervals based on information from the front and rear axle brake pad wear sensors. When replacement of the front and or rear brake pads is necessary, the DSC control module triggers an indicator lamp located in the vehicle's instrument cluster. However, the brake pad indicator lamp may be illuminated although a replacement of the brake pads is not necessary. Additionally, one or both of the following fault codes may be stored in the DSC control module: * 5DE0 Brake-pad wear: plausibility, front axle * 5DE1 Brake-pad wear: plausibility, rear axle CAUSE DSC software error
651310
In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
720111
Safety Belt Extender "Handover" Fails to Deliver the Belt to the Customer. The customer states that the seat belt extender "handover" on the front driver's or passenger side failed to deliver the belt. One or more of the following situations may apply: * The safety belt extender extends but the belt slips off. * The "hand" on the extender fails. * The safety belt is twisted. * The extender will not operate and makes noise while extending. S One or more of the following causes may apply: 1. The safety belt is incorrectly positioned. 2. The "hand" on the extender has mechanically failed. 3. The safety belt slips off the "hand" due to excessive resistance from the seat belt reel, not allowing the belt to extend properly. The seat belt is twisted. 4. The safety belt slips off the "hand" due to the belt material being excessively worn. 5. The safety belt extender fails to extend or retract intermittently due to FRM (Footwell Module) software. 6. The safety belt extender is noisy or inoperative, due to a communication problem or incorrect power or ground.
511511
Headlight Washer Nozzle Cover Sticks Out.
840313
Roadside Assistance and BMW Online Services Inoperative After Programming. Roadside Assistance and BMW Online services are inoperative after programming the vehicle with ISTA/P 2.48 to 2.49.0. The symptoms are as follows: * BMW Online - No network available when selected * Roadside Assistance - When selected, a message stating "Service not enabled or contract expired" is displayed. Also, "Start service" is grayed out and cannot be selected. CAUSE Software error in the CIC (Car Information Computer)
121611
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
130213
N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
540412
Retractable Hard Top (RHT) Is Not Stacking Properly - Frame Bent. The RHT frame is bent or twisted and cannot be operated in either direction, or the roof shells are not stacking properly. The hydraulic roof cylinders operate out of sequence causing the frame to twist.
SIB-11-03-08
BMW: CRANKCASE PRESSURE DIAGNOSIS AND INFORMATION FOR ALL VEHICLES. *RM UPDATED ON 4/24/2013. *KB
SIB-61-13-05
BMW: BATTERY HAS AN INCREASED DEMAND DUE TO DEVELOPEMENTAL PROCESS OF THE ELECTRICAL SYSTEM. THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB
511011
Anti-trap Is Activated when Raising the Front Side Windows. When closing the front side windows using the convertible top switch or the central power window switch, one or both front side windows come to a stop at the top third travel area, and then reverse direction slightly. When the switch is actuated again, the windows will close normally. CAUSE The front side windows contact the rear side windows, causing the anti-trap feature of the front side windows to trigger.
610606
Junction Box Pin Assignment Change. When replacing the Junction Box (fuse box) using P/N 61 14 6 978 270 or later, note that various pin assignments have changed. The following additional work procedure is necessary to properly perform this repair.
650110
CCC - "Please Insert Navigation DVD" Appears on CID. The navigation map DVD cannot be read or detected. The message "Please insert navigation DVD" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head
652212
Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
511508
?SI B51 15 08 Body Equipment October 2012 Technical Service. This Service Information bulletin supersedes SI B51 15 08 dated July 2008. designates changes to this revision SUBJECT Rear Window False Anti-trap Activation. INFORMATION The anti-trap protection feature may be activated when no obstruction is present. This may occur at either one or both of the rear windows. The root cause of the false anti-trap activation may be difficult to determine. The attached diagnosis flowchart has been developed to assist with determining the actual root cause of the failure as well as to help prevent unnecessary part replacements. The root cause is typically either an issue with the window system, or an electrical/software issue. The diagnosis flowchart will help ensure that repairs are only carried out for the system that is most likely at fault. Refer to B511508_Attachment. PARTS INFORMATION Refer to the Electronic Parts Catalog (EPC) for the appropriate parts noted in the diagnostic flowchart. WARRANTY INFORMATION Not applicable.
611305
Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the "Procedure" section of this Service Information for details.
SIB-13-13-10
BMW: ON SOME VEHICLES, THE HIGH PRESSURE FUEL PUMP HAS AN INTERNAL COMPONENT THAT MAY FAIL AND CAUSING DRIVABILITY SYMPTOMS SUCH AS ERRATIC ENGINE OPERATION AND LONGER STARTING TIMES. *PE
SIB-33-01-02
BMW: A GRINDING NOISE IS COMING FROM THE DIFFERENTIAL DURING SLOW CORNERING. WHEN TURNING A SLIP/STICK EFFECT IS CREATED ON THE LINING AND STEEL DISCS INCORPORATED IN THE DIFFERENTIAL CLUTCH CAUSES A GRINDING NOISE. *RM
SIB-63-02-01
BMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
SIB-16-02-09
BMW VEHICLES: FUEL LEVEL SENSOR REPAIRS. WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.