Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B520121
?The front seat will not calibrate/initialize, and the stored faults cannot be deleted.
B650414
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B640613
Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes.
B110120
On rare occasions during an engine oil service, the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing.
B513316
Water sloshing noises coming from the rear passenger compartment (left or right) while driving Water ingress in the luggage compartment, or in the rear passenger compartment- rear seat bench rear passenger compartment foot well rear passenger compartment side panel Failure of various control units installed in the area of the water removal channel
B610721
Groaning, scraping, or squeaking noise coming from the steering wheel area in the interior of the vehicle, when turning the steering wheel.
B840221
The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.
B110321
B58 ENGINE: ENGINE OIL FILTER REMOVAL PROCEDURE AND TOOLS . A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.
B121318
COMBUSTION CONTROL VALVE LIFT AT IDLE: The vehicle will run rough or hesitate when accelerating from a stationary position.
B513218
PAINT ON THE B-PILLAR IS SCRATCHED/DAMAGED: The paint finish of the door jamb (above the door striker) is scratched due to the inner door cavity window seal.
B610419
VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
B650709
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B340517
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
B513016
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B610520
CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.
B652214
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B123314
Fault Code 1D2008 Stored in DME: This Service Information Bulletin (Revision 5) replaces SI B12 33 14 dated February 2016. The Service Engine Soon light is on. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B651519
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
B110119
ENGINE VIBRATIONS OR NOISE This Service Information bulletin replaces SI B11 01 19 dated February 2019.
B520919
CRACKING NOISE FROM SEAT BACKREST. Groaning/Cracking noises are heard from the front seat backrest when the vehicle is cornering.
B651119
Due to an issue during supplier production the driver and/or passenger knee air bags could become damaged during deployment.
B651419
HEAD UNIT NBT EVO (HU-H2) PROGRAMMING ABORT. During programming several aborts can occur in the head unit NBT EVO (HU-H2).
B840214
INFORMATION New information provided by this revision is preceded by this symbol. This Service Information bulletin replaces SI B84 02 14 dated September 2018.
B612315
The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full This Service Information bulletin supersedes SI B61 23 15 dated April 2016.
B512518
RATTLE NOISE FROM LOWER A-PILLAR. A rattle noise is present from the lower area of the A-Pillar. Due to a manufacturing error, the bolt securing the front door brake/stop to the A-Pillar may have loosened over time.
B540907
?RETRACTABLE HARDTOP STATUS REQUEST SUPPLEMENT. INFORMATION Documents have been developed showing the known correct statuses for all hall sensors and micro switches used to operate the retractable hard top (RHT). This document is intended to act as a supplement to the diagnostic information available in ISTA. Comparing these statuses to the actual statuses of a vehicle with a functional problem may assist in narrowing down which sensor/switch is contributing to the functional problem. For E93, the status request may be found by connecting the car to ISTA and selecting: Control module functions/CTM Convertible top module/Diagnosis Requests ?Sensors/Switches For F33/F83, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 F33 F83 RHT Status.pdf. For I15, the statuses should be checked using the applicable test plan as instructed in attachment B54 09 07 I15 Top Status.pd
B613617
BATTERY DISCHARGE CCM (CHECK CONTROL MESSAGE) DISPLAYED: COMFORT ACCESS DISABLED. One or more of the following conditions are present: * CCM "Battery. Discharge in standstill.", or similar, is displayed. * Comfort Access and contactless tailgate opening are not working. * Vehicle can still be unlocked with radio remote control (ID transmitter). Fault conditions are cleared upon engine restart. FEM (Front Electronics Module) software error Unauthorized (radio remote control out of range) access to vehicle has been attempted at least seven times with Comfort Access or Smart Opener (contactless tailgate opening) when the vehicle was locked. As a result of these unauthorized access attempts, the following conditions were set: * CCM "Battery. Discharge in standstill.", or similar, is displayed * Terminal 30F (switched battery terminal when fault occurs) was deactivated, preventing Comfort Access and contactless tailgate opening.
B621017
ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, BMW Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error
B3106170621
Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC73 must appear in the text of your TEC claim.
SIM010917
Shipping specific non-deployed vehicle safety devices to lighting resources, llc. This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC
SISIB011317
Shipping specific non-deployed vehicle safety devices to lighting resources, LLC
B112216
?"ENGINE OIL PRESSURE" ON LOW MILEAGE CARS. Check Control Message (CCM-212) states: "Engine Oil Pressure. Stop Carefully" The following codes may be stored in the DME fault memory" 1C2002 - Engine oil pump, pressure too low 1FB801 - CCM (ID212) - Oil pressure Also, the vehicle's mileage is very low (below 60 miles), the fault frequency shows only "one" occurrence; faults are not currently present and cannot be reproduced. CAUSE Unfavorable DME software application."
B511817
EXTERIOR BMW ROUNDEL EMBLEMS SEPARATE AND FALL OFF. The exterior BMW Roundel Emblem (front and/or rear) separates from the mounting base and falls off. Delamination of the Roundel Emblem.
B620117
TIME DISPLAY (CLOCK) ERROR IN INSTRUMENT CLUSTER. The clock on the basic instrument cluster (KOMBI) gradually loses time even after being reset. Power supply fluctuations cause the time to reset.
B620517
?INSTRUMENT CLUSTER DISPLAYS MIXED UNITS. When the displayed unit of measurement is changed from miles to Kilometers everything except the cruise control or limit set speed is displayed in Kilometers; the set speed is still shown in miles in the Instrument Cluster (Kombi) display. KOMBI software.
B650717
LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."
B840311
?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
B111015
?Service Action: Replace the Thermostat What's New: ? Part number and quantity of coolant has been updated. Refer to the Warranty section for details. . The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
B514416
EXTERIOR MIRROR: CREAKING NOISES Whats new: Video link added This Service Information bulletin supersedes SI B51 44 16 dated January 2017. . Creaking noise coming from either or both exterior rearview mirrors when folding in. Video Link: tinyurl.com/z46agg9 Accumulation of dust in the joint gap seal.
B620217
?Instrument Cluster Failure at Low Ambient Temperature. Sporadically, at low temperatures, the instrument cluster (KOMBI) is not operating (display remains black). KOMBI software.
B650616
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B651715
?ACTIVE SOUND DESIGN (ASD) INOPERATIVE AFTER PROGRAMMING What's New: ? ISTA/P and ISTA 4 software level that contains the fix added to Correction and Procedure ? F31, F32, F33, F34, F36 vehicles added to Models ? Warranty information updated to include programming fix . After programming with ISTA/P V3.56.1 or ISTA/P V3.60: Active Sound Design (ASD) no longer provides simulated engine sounds. A fault is stored in the Active Sound Design (ASD) module. Fault Code 8053A5 "ASD; invalid coding data for equalizing". Invalid ASD coding data in two different versions of ISTA/P.
B840916
?SERVICE ACTION: SUPPLEMENTARY PAGE NEEDED IN OWNER'S MANUAL . Operator's manual of affected vehicles does not contain required information on wireless smartphone charging accessory. AFFECTED VEHICLE Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
B520317
?MISSING AUDIO NOTIFICATION WHEN STORING SEAT MEMORY . When saving seat memory settings (Memory 1 or Memory 2) with a vehicle without navigation, there is no audio tone confirmation. Software error in control unit of Seat Module 2.
B630816
TURN SIGNAL - INTERMITTENTLY FLASHES AT FASTER RATE. Turn signal, intermittently, flashes at faster rate or not at all. Software error in FEM (Front Electronics Module)
B650915
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
B070314
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B122516
B58 -M POWER AND SOUND KIT, MALFUNCTION LIGHT ILLUMINATED. Check engine light illuminated. Check Control Message: Drive faulty". Engine power reduced and set in "Emergency Program". Fault code stored in DME control unit: o 1F0541 - Drive, safety function: Bus signal about engine torque implausible. Fault Code stored in EGS control unit: o CF2C11 - DME/DDE interface: (Actual DME/EGS crankshaft torque, 0xA5, actual crankshaft torque, 0xA5) signal invalid. Affected are vehicles with the following Integration Levels: F020-16-07-5xx F020-16-11-500 F020-16-11-501 DME control unit software error."
B122816
DME Electrical Wastegate Valve Faults - Adaptation Limit Positions Not Detected. Engine runs with reduced power. Emissions warning lamp lights up. One or more of the following faults are entered in the DME fault memory. 123411 "Electrical wastegate valve, limit position teach in: End stop (wastegate valve open) not found 123412 - Electrical wastegate valve, limit position teach in: End stop (wastegate valve open) not found Other consequential faults that also may be stored: 123401 - Electrical wastegate valve, adaptation: Cold start not learned 123437 - Electrical wastegate valve: Jammed closed Problems with electromagnetic compatibility (EMC). The PWM actuation (PWM = pulse-width-modulated) of the heat management module causes a fault condition on the 5V supply line of the electrical wastegate valve controller. This leads to a fault on the position sensor signal of the electrical wastegate valve controller.
B340516
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B111516
B58 ENGINE: OIL LEAK FROM TURBOCHARGER. Engine oil (1) can be seen leaking from the bottom of the turbocharger near the band clamp (2). The turbocharger band clamp is loose.
B513116
HOOD GAS-FILLED SHOCK ABSORBER MOUNT IS BROKEN. Hood gas filled shock absorber is loose or broken, the hood does not remain in the opened position. Gas filled shock absorber mounting point has broken free from the body.
B513216
CREAKING NOISES FROM DOOR TRIM PANEL. Creaking noise is heard from door trim panel while driving on rough roads. Door trim panel is contacting the inner door panel.
B513516
PAINT ON THE B-PILLAR IS SCRATCHED/DAMAGED. Paint on B-pillar is scratched. Especially noticeable on dark colored paint. Door seal is rubbing against entry opening surfaces.
B641216
HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message "Increased battery discharge" - standby current violation may be displayed. Climate control unit (IHKA) software
B120916
N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic.
B540216
GAP VISIBLE BETWEEN UPPER A-PILLAR COWL PANEL SEAL AND CONVERTIBLE TOP SEAL.. When the Retractable Hard Top (RHT) is closed, a gap is visible between the upper A-pillar seal and the cowl panel seal. This concern does not result in water or air leaks, it is only an appearance issue. Photo at left shows gap between Apillar seal and cowl panel seal (inside view). Photo at left shows gap between Apillar seal and cowl panel seal (outside view). Design of upper A-pillar cowl panel seal to convertible top seal.
B640915
This Service Information bulletin supersedes SI B64 09 15 dated January 2016. designates changes to this revision SUBJECT Whistling Noise Coming from the Center Vent - A/C is Off. A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.