Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B010125
The Exhaust Gas Recirculation (EGR) Cooler limited warranty for defects in materials and / or workmanship has been extended to 25 years without mileage limit as determined from the original first in-service / delivery date.
B410722
While driving the vehicle on normal roads at10mph and above, a "cracking" sound from the top of the B-pillar(s) is heard.
B010520
The vehicle demonstrates a power loss and the malfunction indicator lamp (MIL) on. The following fault codes may be stored in the DDE: 24CE00 Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 Charge air hose monitoring in idle: Charge air hose fallen down 290900 Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation
B510819
The basic conditions for initializing the power windows are not met.
B611305
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B310124
With the vehicle is on a lift and the front struts are in the extended position, there may be a cracking and orclicking type noise when turning the steering wheel left/right. See attached video V31 01 24. The sound can reoccur when the vehicle is lowered, and the wheels are once again under load. The noise might also be heard for a short time while driving.
B521823
A noise can be heard from underneath the seat while the seat is being moved either forwards or backwards. This can occur to the driverâÂÂs and/or the passengerâÂÂs front seat.
B010919
DIESEL FUEL INJECTORS: LTD WTY EXTENSION TO 10 YEARS/120,000 MILES
B540421
This situation can result in two customer complaints: 1. Wind noise 2. Excess water entry
B651523
After programming the head unit (HU-H2), activating the FSC (German word Freischaltcode) Enabling Codes repeatedly fails.
B840822
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
B650414
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B662419
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B662719
The Lane Change Warning (LCW) yellow triangle symbol on either one, or both the exterior side view mirrors does not illuminate to alert the driver when it should.
SIB010921
Component-Specific Limited Warranty Extension. For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Leak Diagnosis Module with hose assembly (NVLD, shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date. For eligible MY 2017 BMW 530i Sedan and xDrive (B460) vehicles that are currently registered in the State of California (CA) or a State that has fully adopted the State of California PZEV/SULEV regulation (CT, ME, MD, MA, NJ, NY, RI, and VT), the standard component-related coverage for the NVLD is 15 years/150,000 miles. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Over time, the Leak Diagnosis Module (NVLD) (with connected hose) component material may fail, this can create a fine leak to develop in the Evaporative Emission Control System (EVAP). Should this occur, corresponding fault codes will be stored in the DME memory and the MIL (Malfunction Indicator Lamp) will illuminate.
SIB011219
Component-Specific Limited Warranty Extension. For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Radiator Grille Upper and Lower Active Air Flaps to: 15 years/150,000 miles as determined by the vehicle's original in-service date. 1. Air flap control (link) active, upper (G12, G30 and G32) 2. Air flap control (drive), active, upper 3. Air flaps, upper (assembly) 4. Air flaps, lower (assembly) For eligible MY 2017 BMW 530i (B460) vehicles that are currently registered in the State of California (CA) or a State that has fully adopted the State of California PZEV/SULEV regulation (CT, ME, MD, MA, NJ, NY, RI, and VT), the standard emission-related coverage for the Radiator Front Grille Air Vent Flaps is15 years/150,000 miles. This component-specific limited warranty extension applies to defects in materials or workmanship.' This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. A check control message or MIL (Malfunction Indicator Lamp) may be illuminated with faults stored related to the upper and/or lower active air flap(s). Potential causes include: Faulty upper air flap link (G12, G30, G32) Faulty upper air flap actuator (G01, G02, G12, G30, G32) Faulty upper flap assembly (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02 only) Or: Upon visual inspection, the passenger side upper active air flaps are either stuck open or closed, and they will not move and there are no faults stored for the active air flaps (With no check control message or check engine light or displaying)
SIB510522
BMW AG has issued a Delivery Stop (effective March 28, 2022) on certain Model Year 2022 BMW vehicles that were produced between March 1, 2022 and March 8, 2022 because the torsion struts may not have been installed at the plant. Do not deliver to a customer, a New, Certified Pre-Owned or Used vehicle subject to a Delivery Stop, until the vehicle is repaired. Do not use or sell replacement equipment/parts subject to a Delivery Stop.
SIB840622
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
SIB650122
A check control message for the restraint system appears. In the instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes is stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal 93094F - Knee airbag, front passenger: short circuit to negative terminal.
SIB662419
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.
SIB011918
Component specific limited warranty extension. For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle Nitrogen Oxide (NOx) Sensor(s) to: 10 years/120,000 miles as determined by the vehicle original in-service date.
SIB651312
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B110317
For the above-referenced vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the engine timing chain and oil pump drive chain modules to: 7 years/70,000 miles as determined by the vehicle's original in-service date.
B011417
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's engine high pressure fuel pump (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
B110221
With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered into a nationwide settlement with the plaintiffs in the following class action: Gelis, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC.
B651312
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
SIB110317
BMW of North America, LLC BMW NA is extending the limited warranty for the engine timing chain and oil pump drive chain modules to: 7 years/70,000 miles as determined by the vehicle's original in-service date
B040221
Distribution of the following tool will be through the Automatic Tool Shipment Program
B840221
The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.
B840121
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
B120115
N20 and N26 Differential Pressure Sensor Fault: 195002 Stored in DME: The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
B340517
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B610419
VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
B650709
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B011918
N47/N57T NOX SENSORS BEFORE/AFTER THE SCR-LTD WTY EXT TO 10 YRS/120000 MI: Malfunction indicator lamp (MIL) on.
B110716
Diesel Engine Intake Manifold Damaged: If Recall Campaign 18V-755: Exhaust Gas Recirculation (EGR) Cooler Inspection (and repair) (SI B11 17 18) applies and shows open on an Eligible Vehicle then this bulletin does not apply. The vehicle demonstrates a power loss while driving and illuminated malfunction indicator lamp (MIL).
B513016
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B612115
THE INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES INSTRUMENT CLUSTER DISPLAYS VARIOUS CHECK CONTROL MESSAGES: This Service Information Bulletin (Revision 7) replaces SI B61 21 15 dated October 2018. The instrument cluster displays various check control messages.
B652214
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B840214
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B123314
Fault Code 1D2008 Stored in DME: This Service Information Bulletin (Revision 5) replaces SI B12 33 14 dated February 2016. The Service Engine Soon light is on. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
B641019
SERVICE ACTION: OPTIMIZING THE WATER DRAIN. The water drain in the engine compartment's passenger side cowl near the firewall may be inadequate during exceptionally high water volumes. Water can accumulate and not drain out quickly enough. This can result in various Check Control messages and the failure of various systems such as: Park Distance Control (PDC) Dynamic Stability Control (DSC) Windshield washer This may be caused by one or more parts: Lack of a cowl drainage shaft cover Lid on the ventilation microfilter housing lacks water drainage channels (only on vehicles prior to July 2013 production).
B310514
Front Suspension Ride Height Has Dropped: The front suspension ride height has dropped on one or both sides due to overload. This is caused by driving over obstacles (e.g. potholes) or an impact severe enough for the front spring strut damper to slip through the clamp of the steering knuckle.
B512716
RATTLE/POPPING FROM TAILGATE AREA: There are two related but separate complaints (only one may be present at a time) during driving especially on uneven surfaces. Clicking noises or squeaking noises from the area of the tailgate. Or a popping sound coming from the area of the tailgate.
B541219
RATTLE NOISE FROM SUNROOF AREA: There is a rattle noise present from the area of the sunroof most commonly when driving over rough road surfaces.
B651519
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
B122319
DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL. In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
B110119
ENGINE VIBRATIONS OR NOISE This Service Information bulletin replaces SI B11 01 19 dated February 2019.
B662317
Service Information March 2018 Drivers Assistance Remote Control Systems B66 23 17 Technical Service This Service Information bulletin replaces SI B66 23 17 dated February 2018 CONTACTLESS TAILGATE (SMART OPENER) IS TOO SENSITIVE.
B840311
TELEMATICS CONTROL UNIT ACTIVATION VIA DCSNET FOR BMW ASSIST.
B010418
N47T/N57T DIESEL PARTICULATE SENSOR: LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILEAGE This Service Information bulletin supersedes SI B01 04 18 dated April 2018.
B520818
FRONT PASSENGER SEAT SPORADIC MOVEMENT. Occasional stopping of seat adjustability movement in the driver and front passenger seats when occupied.
B621118
BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: â?¢ Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.
B512518
RATTLE NOISE FROM LOWER A-PILLAR. A rattle noise is present from the lower area of the A-Pillar. Due to a manufacturing error, the bolt securing the front door brake/stop to the A-Pillar may have loosened over time.
B540818
SUNROOF REPAIR KIT COMPONENTS. Based on feedback from technicians, it can be difficult to identify the individual components included with sunroof repair kits. In some cases complete sunroofs are replaced, when a sunroof repair kit could have been used. This bulletin covers the contents of the sunroof repair kits in order to help you identify the correct repair for the vehicle you are working on.
B613017
RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B840616
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B110618
TURBO BOOST ACTUATOR ROD LOOSE (DIESEL): Limited engine performance (lack of boost) with a Malfunction Indicator Lamp (MIL) illuminated.
B512915
SERVICE ACTION: REAR SIDE WINDOW: Both rear side fixed windows need to be replaced due to incorrect glue application, this may cause a water leak.
B520318
MEMORY SEAT ADJUSTMENT IS LIMITED: After programming the vehicle with ISTA 4.10.2x, the adjustment range of the memory seat may restricted.
B651316
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.: If either the head unit (NBT-EVO or ENTRY-NAV-EVO) or the Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit to enter a locked mode once it recognizes a different VIN.
B620618
FUEL GAUGE INCORRECTLY DISPLAYING LOW FUEL LEVEL: Occasionally, on restart after refueling, the fuel gauge will display the fuel level as low (minimum) and the range display will be at an implausible (maximum) value.
B651117
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START: Navigation system will not start at all or the: ÒNavigation system startsÓ message is permanently displayed; or
B660517
DOOR CANNOT BE OPENED WITH COMFORT ACCESS: One or more doors are unable to be opened from the outside of the vehicle using the Comfort Access System.
B840818
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:
B621215
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
B840718
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition.
B840618
CONNECTEDDRIVE-REMOTE SERVICES DO NOT FUNCTION: Remote Services (such as locking and unlocking the car, vehicle location by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has been sitting for extended amount of time (In excess of 20 hours).
320218
CHECK CONTROL MESSAGE (CCM): ASSISTANCE SYSTEM RESTRICTED AFTER DELETING TRANSPORT MODE: The CCM assistance systems restricted or pedestrian protection system failed is displayed after deleting transport mode.
B110115
Engine Oil Quick Reference Chart and Drain Plug Torque: The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive.
B111417
N20 AND N26 ENGINES TURBOCHARGER ELECTRIC WASTEGATE ACTUATOR LINKAGE PIN CORROSION This Service Information bulletin replaces SI B11 14 17 dated February 2018.
B840218
HEAD UNIT HIGH RESETS WITH CONNECTION OF IPHONE 8, IPHONE 8+ OR IPHONE X
B841117
BMW APPS RANDOMLY STARTS PLAYING ON ITS OWN: While listening to FM, or AM, or Satellite Radio (SDARs), the audio source randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.
B650318
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback.
B840314
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B010116
N20 Engine Coolant Thermostat: Limited Warranty Extension to 10 Years/120,000 Miles
B650915
NBT Head Unit High (HU-H) Resets Intermittently or Permanently
B540617
WATER LEAK NEAR ROOF FUNCTION CENTER (FZD): Dampness is noticed on the roof liner near the Roof Function Center and/or the hands free microphone.
B611915
Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
B621017
ERRONEOUS SERVICE INCLUSIVE CBS DISPLAY. After pre-delivery check or after instrument cluster exchange, BMW Service Inclusive is displayed although the vehicle does not feature the optional Service Inclusive coverage. Instrument Cluster display error
B160117
VOLUNTARY EMISSIONS RECALL CAMPAIGN 17E-A02 - REPLACE ACTIVATED CHARCOAL FILTER AND NVLD SENSOR HOLDER This Service Information bulletin replaces SI B16 01 17 dated March 2017 What's New: ? Bulletin type was changed from a Service Action to an Emissions Recall. The activated charcoal canister and or NVLD sensor holder may be damaged. AFFECTED VEHICLES This Emissions Recall Campaign affects F25 and F26 vehicles produced from February 2017 to March 2017 First check if a Recall Completion Label, SD 92-435 for this campaign is already attached to the underside of the hood on the right (passenger) rear close to the windshield. If the label is present, the Campaign has already been performed and no further action is necessary. Affected vehicles which require this Recall Campaign to be completed will show it as "Open" when checked either in AIR, the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. LABEL INSTRUCTIONS For California centers only: It is required by the California Code of Regulations that an executed orange "Vehicle Emission Recall - Proof of Correction" certificate (SD92-084, see illustration) be provided to each customer (for vehicles registered in the state of California), once the Recall on his or her vehicle has been completed. The activated charcoal canister and NVLD sensor holder are damaged Transportation damage.
B621616
WARRANTY INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.
B130315
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B620117
TIME DISPLAY (CLOCK) ERROR IN INSTRUMENT CLUSTER. The clock on the basic instrument cluster (KOMBI) gradually loses time even after being reset. Power supply fluctuations cause the time to reset.
B840316
SERVICE ACTION: GSM COMBOX DEACTIVATION / DISCONTINUATION WITH 4 YEAR ASSIST SERVICE. What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B840816
The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.
B620217
?Instrument Cluster Failure at Low Ambient Temperature. Sporadically, at low temperatures, the instrument cluster (KOMBI) is not operating (display remains black). KOMBI software.
B650616
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B180117
? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message "Drive faulty" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF.
B180310
? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The 10146535 20181105 B180310 20170201 Service Bulletin/Repair Instructions BMW 320I 2017 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM ? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B070314
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
B630516
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by "condensation" rather than a "water leak" into the headlight housing, there will be misting/condensation in "both headlights."
B652616
USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: "Title cannot be reproduced" "Is being read" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB.
B340516
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652016
CID Split Screen Always Changes Back to Compass Display. This Service Information bulletin Replaces SI B65 20 16 dated June 2016. After starting the vehicle, the Control Display (CID) right side (split screen) display does not stay on the last selection made by the driver. Within 30 seconds of starting the right side of the display changes by itself to the compass view. Software error (Head Unit NBT-EVO ID5) was introduced with ISTA/P V3.58.0 (16-03-502 I Level).
B652316
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B652416
NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes "without a cash option" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes "without cash option". UPDATE Install new map data.
B652516
USB CABLE: BATTERY DISCHARGE/AUDIO FAILURE/RADIO RECEPTION. No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.
B662116
KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B121816
CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
B611416
WASHER FLUID LEAKS FROM THE HEADLIGHT WASHER JETS This Service Information bulletin supersedes SI B61 14 16 dated August 2016.. Washer fluid leaks from the headlight cleaning washer jets. Calcification buildup causes washer fluid to leak out of the headlight cleaning washer jets.
B130216
DDE FAULT CODE 290900 AFTER PROGRAMMING. The engine has a hesitation and the Service Engine Soon lamp is on after programming the vehicle to an Integration level of 16-07-500. The following fault code may be stored: 290900 - Air system, air to EGR exhaust mass flow plausibility Unfavorable DDE software application The fault will be stored if terminal 15 is switched on, and then off, without starting the engine.
B511615
Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2
B661816
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B840516
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B120916
N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic.
B611814
Various Electrical Faults Caused by Shorted K-CAN2 This Service Information bulletin supersedes SI B61 18 14 dated July 2014. One or more of the following situations can occur when the K-CAN2 wiring in the vehicles is shorted. There is no communication with any K-CAN2 control modules during an ISTA vehicle test. The following control modules are on the K-CAN2: ZGM - Central Gateway Module FRM - Footwell Module CAS - Car Access System Headunit - Radio/Navigation ComBox/TCB - Telematic Control Module FZD - Roof Function Center Module JBE - Junction Box Electronics The transmission will not engage a gear when with the engine running. The vehicle sporadically does not start. In rare cases, the vehicle may stop running while driving. When the K-CAN2 is shorted, the vehicle will store many line and communication faults for the KCAN2, including the following: JBE - C9140D No message, receiver JBE, transmitter CAS JBE - C90468 K-CAN2; Communication fault ZGM - CD0468 K-CAN2: Communication fault ZGM - CD1400 Message incorrect, receiver ZGM, transmitter JBE CAS -D9045F K-CAN2: Line fault CAS - D90468 K-CAN2: Communication fault FZD - DE8468 K-CAN2: Communication fault TCB - E14468 K-CAN2: Communication fault TCB - E1445F K-CAN2: Line fault NBT - E1C468 K-CAN2: Communication fault FRM - E5845F K-CAN2: Line fault FRM - E58468 K-CAN2: Communication fault The wiring harness gets pinched between the instrument panel and the locating tab on the passenger side of the instrument panel. Connector X18*2b not fully connected (located above rear distribution box in trunk) K-CAN2 High - GE/RT (Yellow/Red) K-CAN2 Low - GE/BR (Yellow/Brown).
B111316
Delivery Stop to replace cylinder head F25 (X3).
B621016
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B511216
Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
B620816
Incomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
B651216
Integrated Navigation Voice Not Loud Enough. Integrated Navigation voice guidance is not loud enough to be heard over loud music. Software error in the CHAMP2 Head Unit.
B660916
"Collision Warning Failed" or "Pedestrian Warning Failed" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the "green lines"
TEC24
Tech24 Snap-in Adapter Return
B111615
N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
B660816
Comfort Access Sporadically Malfunctions. Any or all doors, including rear tailgate, cannot be opened from the outside door handle via CA (Comfort Access). Faults in CA for aerial short(s). Faults for door handle(s). Rapid opening and close (system overheating). No faults in the system and malfunction is sporadic or in a certain area; the situation is caused by interference to the signal.
B840715
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
TEC26
TEC26 Turbo Charger Return
TEC25
Tec25 Wishbone Return
B650716
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
SIM010603
MINI "Enhanced" dealer self authorized (DSA)K goodwill program
SIM110115
MINI engine oil part number transition and model year 2016 engine oils
B160116
Location of Anti-Tampering Screws for SCR Components. Refer to the attachment for proper location of the screws. PDF attachment B160116_Location_of_anti-tamper_cover.
B610314
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B650216
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B610116
The Windshield Wipers Come On Erroneously. The windshield wipers come on by themselves without activating the switch. This can happen at vehicle start or while driving. Communication error between the SZL (Steering Column Switch Center) and the JBBF (Junction Box Co Driver).
B620316
?Clock gains or loses time. The time displayed in the KOMBI (instrument cluster) may gain or lose a few minutes each week. Internal KOMBI calculation error.
B621415
Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
B620715
Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles "arriving" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed "prior" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2.
B621015
Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 "display backlighting and graphics PCB switched off" stored. Kombi software.
B270415
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B640815
The AUC (Automatic Recirculation Sensor) is installed pointing upwards instead of downwards. The AUC becomes contaminated. AFFECTED VEHICLES This Service Action involves F25 (X3) and F26 (X4) vehicles produced from July 31, 2015 to August 25, 2015. ONLY 41 vehicles are involved. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.
B840315
HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows "Please wait" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows "Please wait" Incorrect software installed in the HU-B (Headunit Basic).
B111315
The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
B160615
Deformation of the Fuel Tank. The vehicle loses power while driving. There may also be a complaint of difficulty refilling the tank. CAUSE There is inadequate venting of the fuel tank. This results in a lack of pressure compensation (vacuum) in the fuel tank as the level drops which causes the tank to collapse.
B270315
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
B512115
Tailgate intermittently cannot be opened or closed. One or more of the following situations can occur, if the tailgate striker is not adjusted properly: ? The tailgate does not lock ? The tailgate does not remain locked ? The tailgate does not close ? The tailgate does not remain closed ? The tailgate does not open CAUSE The tailgate lock striker is not adjusted correctly.
B122114
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B651015
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
B360215
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B631214
Check Control Message with Rear Light Failure. Intermittently, a Check Control Message (CCM) is displayed for one or more rear light failures: ? Rear light ? Brake light ? Rear indicator One or more fault codes are registered in the Footwell Module (FRM) for one or more circuits with the fault not currently present: ? 800F46 - Indicator rear left defective ? 800F47 - Indicator rear right defective ? 800F56 - Brake light left defective ? 800F57 - Brake light right defective ? 800F80 - BFD left defective ? 800F81 - BFD right defective ? 802812 - Brake light / direction indicator, left: light faulty or open circuit ? 802813 - Brake light / direction indicator, right: light faulty or open circuit ? 800F7A - Reversing light left defective ? 800F7B - Reversing light right defective CAUSE Bad connection at the rear light in the tailgate and/or rear light in the side panel
B640314
A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
B160415
Service Action: Program Control Units (SCR). The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
B660115
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B110315
N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
B840514
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
122114
SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
160215
SUBJECT Service Action: Program Control Units (SCR). An error in the calculation of the DEF line pressure by the SCR module software could occur at temperatures below 32°F/0°C. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
610314
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
650414
Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself.
120115
SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
120415
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
120915
SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the "fuel consumption, current" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold.
123814
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
161614
SI B16 16 14January 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B16 16 14 dated December 2014. designates changes to this revision SUBJECT Service Engine Soon Light (MIL) Is On with SCR Faults Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. F25 (X3) only: z 8051B0 - Metering line heating, power too high SCR module software error
650509
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
651009
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
651312
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
652413
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.