B010122
Service Bulletin/Repair Instructions
N63TU1 CLASS ACTION SETTLEMENT SVC CAMPAIGN: OIL CONSUMPTION DIAGNOSIS/REPAIR
Vehicle report
2016 BMW X5
Service bulletins
235 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B011125
Warranty Program/Extension
The Exhaust Gas Recirculation (EGR) Cooler (with EGR Valve) and the Auxiliary Exhaust Gas Recirculation (EGR) Cooler limited warranty for defects in materials and / or workmanship has been extended to 25 years without mileage limit as determined from the original first in-service / delivery date.
B011025
Warranty Program/Extension
The electric auxiliary heater assembly limited warranty for defects in materials and / or workmanship has been extended to 10 years / 120,000 miles as determined from the original first in-service / delivery date
B010924
Warranty Program/Extension
The High-Voltage (HV) Battery Assemblys Cell Modules Temperature Sensors (Internal NTC repair kit-specific) limited warranty for defects in materials or workmanship has been extended to 10 years / 120,000 miles as determined from the original in-service/first delivery date
B010520
Service Bulletin/Repair Instructions
The vehicle demonstrates a power loss and the malfunction indicator lamp (MIL) on. The following fault codes may be stored in the DDE: 24CE00 Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 Charge air hose monitoring in idle: Charge air hose fallen down 290900 Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation
B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B360121
Service Bulletin/Repair Instructions
At low outside temperatures (below 40 degrees F) and slow driving speeds (i.e. when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned. This can be felt (jerking)/ heard via an acoustic acknowledgement (clunk) as seen at the 11 second mark of the video. See attached video V36 01 21.
B320223
Service Bulletin/Repair Instructions
SITUATION Unusual noises occur only when operating the steering column in the axial direction. 1. A one-time thump sound at the start of movement Shortly after the steering column starts moving, retracting, or extending, a one-time thump noise is heard. See attached video V32 03 23 2. Humming noise while steering column extends in the axial direction. The sound is only heard when the steering column is extended, not when the steering column is retracted. When the steering column starts to move in the extended direction, the humming noise can be heard. See attached video V32 04 23
B160623
Service Bulletin/Repair Instructions
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
B653423
Service Bulletin/Repair Instructions
Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicleâÂÂs equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
B010919
Service Bulletin/Repair Instructions
DIESEL FUEL INJECTORS: LTD WTY EXTENSION TO 10 YEARS/120,000 MILES
B522319
Service Bulletin/Repair Instructions
Second seat row blocking access to third seat row, program seat modules. Visible stitching on first row sport seat. Third seat row backrest Bowden cable routing and length change.
B660523
Service Bulletin/Repair Instructions
Various functions of the camera-based driver assistance systems (ADCAM system) can lead to customer complaints.
B540421
Service Bulletin/Repair Instructions
This situation can result in two customer complaints: 1. Wind noise 2. Excess water entry
B520121
Service Bulletin/Repair Instructions
?The front seat will not calibrate/initialize, and the stored faults cannot be deleted.
B514616
Service Bulletin/Repair Instructions
Upon opening and closing the tailgate, a creaking/groaning sound can be heard from tailgate actuator.
B651523
Service Bulletin/Repair Instructions
After programming the head unit (HU-H2), activating the FSC (German word Freischaltcode) Enabling Codes repeatedly fails.
B840822
Service Bulletin/Repair Instructions
The 3G network in the US has been shut down. This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.
B650414
Service Bulletin/Repair Instructions
According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
B170222
Service Bulletin/Repair Instructions
Coolant is leaking from under the car which is equipped with the S63 engine. A low coolant warning might also be displayed (CC Message ID166).
B520419
Service Bulletin/Repair Instructions
The driver's side (left rear) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail).
B520422
Service Bulletin/Repair Instructions
When returning the 2nd row seat 60% (left) side from Easy-Entry: The seat stops moving before reaching the final home position, a check control message (CCM) appears alerting the customer that the seat back is unlocked.
B520622
Service Bulletin/Repair Instructions
When returning the 2nd row seat 40% (right) side from Easy-Entry: The seat stops moving before reaching the final home position, a check control message (CCM) appears alerting the customer that the seat back is unlocked. The passenger's side (right rear 40% seat) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail).
B521919
Service Bulletin/Repair Instructions
The passenger's side (right rear) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail).
B610120
Service Bulletin/Repair Instructions
Customer is unable to power up or charge accessories through a plug adapter inserted in the front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained.
B662419
Service Bulletin/Repair Instructions
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B662719
Service Bulletin/Repair Instructions
The Lane Change Warning (LCW) yellow triangle symbol on either one, or both the exterior side view mirrors does not illuminate to alert the driver when it should.
SIB660322
Service Bulletin/Repair Instructions
Driver Assistance reduced checked control message (CCM) appears. All or some of the system functions maybe inoperative. The following fault will be stored: 481CC6.
SIB160222
Service Bulletin/Repair Instructions
The fuel gauge may indicate the incorrect fuel level (full and reserve).
SIB011418
Service Bulletin/Repair Instructions
Component specific limited warranty extension for the Exhaust Gas Recirculation Valve.
SIB650222
Service Bulletin/Repair Instructions
A check control message for the restraint system appears. In the Instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal; 93094F - Knee airbag, front passenger: short circuit to negative terminal.
SIB662419
Service Bulletin/Repair Instructions
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.
SIB011918
Service Bulletin/Repair Instructions
Component specific limited warranty extension. For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle Nitrogen Oxide (NOx) Sensor(s) to: 10 years/120,000 miles as determined by the vehicle original in-service date.
SIB651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B513019
Service Bulletin/Repair Instructions
A groaning noise is present from the door frame of any door, most commonly when driving over rough roads or during body flex. This situation may be worse in vehicles which are regularly waxed in the area of the door jamb.
B010222
Service Bulletin/Repair Instructions
BMW of North America, LLC (BMW NA) has entered into a nationwide settlement with the plaintiffs in the following class action: Isley, et al. v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.
B011921
Service Bulletin/Repair Instructions
For the eligible vehicles with the Electrical Machine Electronics (EME) wiring harness connector (A190*1B), BMW of North America (BMW NA) is providing a repair-specific extended limited warranty to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
B650518
Service Bulletin/Repair Instructions
The red air bag warning light is illuminated.
B011417
Service Bulletin/Repair Instructions
For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's engine high pressure fuel pump (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.
B341019
Service Bulletin/Repair Instructions
Inform the customer during a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty, dynamic driving styles. As a side effect of the highest possible brake performance, customers are likely to hear noises due to the extremely resilient materials. In the same conversation, inform the customer that his/her braking performance can help ensure that the noises do not occur or disappear quickly.
B651312
Service Bulletin/Repair Instructions
The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
B840221
Service Bulletin/Repair Instructions
The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.
B840121
Service Bulletin/Repair Instructions
TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
B340414
Service Bulletin/Repair Instructions
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B340515
Service Bulletin/Repair Instructions
TICKING NOISE FROM THE FRONT AXLE WHEN CORNERING: The customer may complain of a metallic ticking noise from the front axle, when cornering, maneuvering, parking or pulling away from a parking space.
B612315
Service Bulletin/Repair Instructions
Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full: Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.
B611820
Service Bulletin/Repair Instructions
BMW TURBOCORD PORTABLE EV 120 V/240 V CHARGER: The BMW-approved accessory TurboCord electric vehicle (EV) charger will not charge the vehicle.
B310112
Service Bulletin/Repair Instructions
CRACKING NOISES FROM THE FRONTAXLE AREA WHILE TURNING THE WHEELS, WHEN STATION: Cracking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.
B340517
Service Bulletin/Repair Instructions
TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
B610419
Service Bulletin/Repair Instructions
VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
B650709
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
B011918
Service Bulletin/Repair Instructions
N47/N57T NOX SENSORS BEFORE/AFTER THE SCR-LTD WTY EXT TO 10 YRS/120000 MI: Malfunction indicator lamp (MIL) on.
B110716
Service Bulletin/Repair Instructions
Diesel Engine Intake Manifold Damaged: If Recall Campaign 18V-755: Exhaust Gas Recirculation (EGR) Cooler Inspection (and repair) (SI B11 17 18) applies and shows open on an Eligible Vehicle then this bulletin does not apply. The vehicle demonstrates a power loss while driving and illuminated malfunction indicator lamp (MIL).
B122716
Service Bulletin/Repair Instructions
DIAGNOSING NON FUNCTIONING eDRIVE: Vehicle will not go into "eDrive". No pertinent electric drivetrain fault codes to assist with diagnosis. "eDrive" may be greyed-out in the Central Information Display (CID) and is not selectable. MSA deactivation. 12 Volt battery failure. Intelligent Battery Sensor (IBS) failure.
B122818
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL) MULTIPLE MOTOR POSITION SENSOR FAULTS STORED IN EME: The following check control messages are displayed: CCM 34 "Malfunction indicator lamp (MIL)" CCM 633 "Powertrain Malfunction!".
B513016
Service Bulletin/Repair Instructions
TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
B610920
Service Bulletin/Repair Instructions
CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.
B611420
Service Bulletin/Repair Instructions
DEACTIVATION OF THE INTERIOR MOVEMENT DETECTOR/TILT ALARM SENSOR IS NOT POSSIBLE: Customer complains that the interior movement detector and the tilt alarm sensor system cannot be deactivated by pressing the lock button on the remote control / BMW display key twice. The second button press on the radio remote control / BMW display key is not detected. Customer may have to press the button 3 times to deactivate the interior movement detector and tilt alarm sensor. CAUSE Software error in the control unit of the roof function center (FZD).
B652214
Service Bulletin/Repair Instructions
AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
B840214
Service Bulletin/Repair Instructions
CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
B010220
Service Bulletin/Repair Instructions
LIMITED WARRANTY EXTENSION TO 15 YEARS/150000 MILES: Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on with the following fault codes stored in the DME: Misfires While there are various possible causes a possible cause might be that one or more fuel injectors are leaking/defective.
B010518
Service Bulletin/Repair Instructions
LIMITED WARRANTY EXTENSIONTO 10 YEARS/120000 MILES: This Service Information Bulletin replaces SI B01 05 18 dated July 2019. Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.
B320115
Service Bulletin/Repair Instructions
NOISE WHEN ADJUSTING THE STEERING COLUMN UP OR DOWN: Creaking noise when raising or lowering the steering column position. CAUSE Steering column adjustment.
B611819
Service Bulletin/Repair Instructions
VEHICLE WILL NOT UNLOCK USING THE REMOTE CONTROL KEY BUTTON. The vehicle cannot be unlocked using the remote control key button. However, comfort access operates normally at the front door handles and the tailgate.
B512716
Service Bulletin/Repair Instructions
RATTLE/POPPING FROM TAILGATE AREA: There are two related but separate complaints (only one may be present at a time) during driving especially on uneven surfaces. Clicking noises or squeaking noises from the area of the tailgate. Or a popping sound coming from the area of the tailgate.
B540719
Service Bulletin/Repair Instructions
GURGLING NOISE FROM SUNROOF DRAINS: A gurgling noise can be heard from the front sunroof.
B651519
Service Bulletin/Repair Instructions
SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
B122319
Service Bulletin/Repair Instructions
DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL. In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
B110119
Service Bulletin/Repair Instructions
ENGINE VIBRATIONS OR NOISE This Service Information bulletin replaces SI B11 01 19 dated February 2019.
B110919
Service Bulletin/Repair Instructions
N55 ENGINE: FC 28A0 OR 101F01 THROTTLE VALVE OPENING ANGLE. The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.
B121018
Service Bulletin/Repair Instructions
MALFUNCTION INDICATOR LAMP (MIL): IHKA FC 801386 This Service Information bulletin supersedes SI B12 10 18 dated April 2018.
B121519
Service Bulletin/Repair Instructions
Service Information May 2019 Engine Electrical Systems B12 15 19 Technical Service. Production fault on a printed circuit board of the electrical machine electronics (EME). In the event of an EME failure a yellow check control message is displayed on the KOMBI; caused by the shutdown of the high-voltage system. The combustion engine is started and driving is stil possible.
B610619
Service Bulletin/Repair Instructions
HIGH VOLTAGE DIAGNOSTIC SPECIALIST TRAINING AND EQUIPMENT STRATEGY. INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians.
B840311
Service Bulletin/Repair Instructions
TELEMATICS CONTROL UNIT ACTIVATION VIA DCSNET FOR BMW ASSIST.
B010418
Service Bulletin/Repair Instructions
N47T/N57T DIESEL PARTICULATE SENSOR: LIMITED WARRANTY EXTENSION TO 10 YEARS/120000 MILEAGE This Service Information bulletin supersedes SI B01 04 18 dated April 2018.
B120919
Service Bulletin/Repair Instructions
EME GROUND CONNECTION MONITORING FAULTS - CCM - DRIVE. CHECK AS SOON AS POSSIBLE. The following check control messages are displayed: CCM 794 - Drive.
B611918
Service Bulletin/Repair Instructions
STANDARD OCCASIONAL USE CABLE CHARGING COMPLAINT TROUBLESHOOTING This Service Information bulletin supersedes SI B61 19 18 dated November 2018.
B640219
Service Bulletin/Repair Instructions
HUMMING NOISES WHEN AIR CONDITIONING IS ACTIVATED. Humming or high-pitched vibrating noises can be heard inside the vehicle when the air conditioning (A/C) is switched on.
B340816
Service Bulletin/Repair Instructions
Modified front brake pads are being supplied. Installation of these new brake pads addresses customers complaint of "front brake noise in a stop & go traffic conditions".
B512918
Service Bulletin/Repair Instructions
AUTOMATIC HATCH DOES NOT OPEN COMPLETELY.
B621118
Service Bulletin/Repair Instructions
BLACK SPOT IN THE CENTRAL INFORMATION. This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: â?¢ Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.
B110113
Service Bulletin/Repair Instructions
N63 AND N63T ENGINE: ENGINE OIL CONSUMPTION, ENGINE OIL TOP-UPS AND REFILL CAPACITY. Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.
B160918
Service Bulletin/Repair Instructions
SCR SYSTEM FAULT 805256 STORED IN VERY COLD WEATHER. After the vehicle is exposed to prolonged temperatures under -9°C (15.8°F) and is then driven a long distance when temperatures are above -9°C (15.8°F), the check engine light may be illuminated. The following fault may be stored in the Digital Diesel Electronics (DDE) 805256 - Active tank filling level sensor, signal: echo fault In low temperature under -9°C (15.8°F) a layer of ice may form in the active tank. This can result in an incorrect level measurement after the vehicle is driven.
B511614
Service Bulletin/Repair Instructions
DOOR OPENS TO FIRST STAGE WHILE DRIVING. The door opens to the first stage and the "Door Open" indicator (pictogram) will indicate the door affected. This can affect any door. Automatic soft-close drive (Bowden cable lock). Soft-Close Automatic drive (SCA) locking levers are slow to respond to lock request.
B540818
Service Bulletin/Repair Instructions
SUNROOF REPAIR KIT COMPONENTS. Based on feedback from technicians, it can be difficult to identify the individual components included with sunroof repair kits. In some cases complete sunroofs are replaced, when a sunroof repair kit could have been used. This bulletin covers the contents of the sunroof repair kits in order to help you identify the correct repair for the vehicle you are working on.
B611018
Service Bulletin/Repair Instructions
THE DISPLAY GOES BLACK, THE ENGINE CAN BE SWITCHED OFF ONLY VIA THE EMERGENCY-OFF.. * On board computer and navigation system goes black or resets. * The engine can only be switched off by pressing the START/STOP button three times (Emergency STOP) * Various Check Control messages are displayed. * At a minimum the following fault code is present: D91C86 - CAN message, status functional safety (ST_FSSY): Timeout-BDC * Additional fault messages may also be displayed Software error in the central gateway of the Body Domain Controller (BDC) control unit. Note: Parts replacement does NOT provide a solution!
B613017
Service Bulletin/Repair Instructions
RAIN/LIGHT SENSOR (RLS): OIL LEAKAGE FROM GEL PAD. ??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.
B640318
Service Bulletin/Repair Instructions
DELIVERY STOP: REFRIGERANT AIR CONDITIONING. An incorrect refrigerant was used to fill the refrigerant circuit in the affected vehicles after assembly. AFFECTED VEHICLES This Service Action involves X5 or X6 (Only 8 vehicles) vehicles produced from January 16 to February 19, 2018. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR, the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. The affected vehicles will be identified with the description: 0064950100 B640318 Delivery Stop: Refrigerant Air Conditioning.
B111117
Service Bulletin/Repair Instructions
?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
B660118
Service Bulletin/Repair Instructions
?REMOTE KEY WILL NOT OPEN OR START VEHICLE. Remote key battery in service significantly less (under a year) than expected two-year life-span. Remote key will NOT: * Open/close vehicle door locks * Start engine (except when held directly against steering column) CC message "Battery of remote key empty (ID:00067)" displayed Fault memory entry "BDC 804415- ID Transmitter: Battery under-voltage" stored Remote key battery has been drained, possibly by elevated standby current (faulty capacitor).
B840616
Service Bulletin/Repair Instructions
?BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).
B010918
Service Bulletin/Repair Instructions
HIGH-VOLTAGE BATTERY SAFETY BOX: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILEAGE: For the eligible vehicles, BMW of North America, LLC (ÒBMW NAÓ) is extending the limited warranty for the vehicleÕs high-voltage battery safety box to:
B011318
Service Bulletin/Repair Instructions
X5 PHEV, I3 REX AND I8 FUEL TANK PRESSURE SENSOR: LIMITED WARRANTY EXTENSION TO 10 YEARS/120,000 MILES: For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicleÕs Fuel Tank Pressure Sensor to:
B110618
Service Bulletin/Repair Instructions
TURBO BOOST ACTUATOR ROD LOOSE (DIESEL): Limited engine performance (lack of boost) with a Malfunction Indicator Lamp (MIL) illuminated.
B520318
Service Bulletin/Repair Instructions
MEMORY SEAT ADJUSTMENT IS LIMITED: After programming the vehicle with ISTA 4.10.2x, the adjustment range of the memory seat may restricted.
B651316
Service Bulletin/Repair Instructions
COMPONENT PROTECTION ACTIVE. HEAD UNITS CANNOT BE SWAPPED BETWEEN VEHICLES FOR TESTING.: If either the head unit (NBT-EVO or ENTRY-NAV-EVO) or the Body Domain Controller (BDC) are swapped into a different vehicle they will cause the head unit to enter a locked mode once it recognizes a different VIN.
B610818
Service Bulletin/Repair Instructions
SME FCS 21F156 21F1F7: The following codes are saved in the battery management electronics (SME) fault memory:
B651117
Service Bulletin/Repair Instructions
NAVIGATION PRO (NBT EVO) MAP UPDATE NOT POSSIBLE, NAVIGATION DOES NOT START: Navigation system will not start at all or the: ÒNavigation system startsÓ message is permanently displayed; or
B840818
Service Bulletin/Repair Instructions
HEAD UNIT HIGH 2 RESET WHILE BLUETOOTH IS CONNECTED: The following event may cause an unexpected reset of the Head Unit High 2 (NBT EVO) when:
B121218
Service Bulletin/Repair Instructions
DRIVE WARNING CCM MESSAGES: Check Control Massages (CCM) displayed:
B621215
Service Bulletin/Repair Instructions
INSTRUMENT CLUSTER OUTSIDE TEMPERATURE DISPLAY IMPLAUSIBLE: In the Instrument Cluster (Kombi) display you may observe an implausible outside temperature reading.
B840718
Service Bulletin/Repair Instructions
IPHONE: CALL LIST MISSING AFTER RESTART: The call list from iPhone 8 or iPhone X, that is displayed, is missing after cycling the ignition.
B310117
Service Bulletin/Repair Instructions
TICKING NOISE FROM FRONT AXLE ON TURNS: A hard mechanical clacking noise is heard when making turns coming from the front axle.
B330315
Service Bulletin/Repair Instructions
LEAKING REAR DIFFERENTIAL (QMVH): There is an oil leak from the rear differential housing.
B610118
Service Bulletin/Repair Instructions
HIGH VOLTAGE SYSTEM: ISOLATION FAULTS: The Check Control message (CCM), "Powertrain malfunction!" is displayed.
B613014
Service Bulletin/Repair Instructions
BMW Maintenance Program: 12-Volt Battery Replacement Measure: This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above.
B630516
Service Bulletin/Repair Instructions
HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION: Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside.
B641216
Service Bulletin/Repair Instructions
HVAC BLOWER NOT WORKING: HVAC blower is not working.
B641316
Service Bulletin/Repair Instructions
A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED: Air conditioning (A/C) failure with IHKA fault code "801252 - Electric A/C compressor: Internal fault detected".
B840618
Service Bulletin/Repair Instructions
CONNECTEDDRIVE-REMOTE SERVICES DO NOT FUNCTION: Remote Services (such as locking and unlocking the car, vehicle location by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has been sitting for extended amount of time (In excess of 20 hours).
B110115
Service Bulletin/Repair Instructions
Engine Oil Quick Reference Chart and Drain Plug Torque: The current version of ISTA/D has an error in the engine oil capacity specification for all vehicles with the N63R engine and xDrive.
B111417
Service Bulletin/Repair Instructions
N20 AND N26 ENGINES TURBOCHARGER ELECTRIC WASTEGATE ACTUATOR LINKAGE PIN CORROSION This Service Information bulletin replaces SI B11 14 17 dated February 2018.
B120618
Service Bulletin/Repair Instructions
DME FAULT CODE CDC203: Various control units contain faults indicating missing messages from the battery management electronics
B841117
Service Bulletin/Repair Instructions
BMW APPS RANDOMLY STARTS PLAYING ON ITS OWN: While listening to FM, or AM, or Satellite Radio (SDARs), the audio source randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.
B650318
Service Bulletin/Repair Instructions
NO AUDIO PLAYBACK AFTER REPLACING THE HEAD UNIT HIGH 2 (HU-H2): After replacing the Head Unit High (HU-H2) and performing ISTA4 programming, there is no audio playback.
B840314
Service Bulletin/Repair Instructions
Bluetooth Connection Failures: There are various connectivity failures with the following devices: Apple iPhones: Samsung S6 and the S6 Edge.
B614317
Service Bulletin/Repair Instructions
EME FAULT CODES S0728 / S0729: A fault (S0728 for F15 PHEV or S0729 for i3) is found stored in the EME during ISTA short test. Diagnostic instructions indicate to reprogram EME.
B614617
Service Bulletin/Repair Instructions
LACK OF POWER OR DRIVING READINESS CANNOT BE ESTABLISHED: Drive parameters (speed and torque) may be restricted.
B650915
Service Bulletin/Repair Instructions
NBT Head Unit High (HU-H) Resets Intermittently or Permanently
B710317
Service Bulletin/Repair Instructions
RECALL CAMPAIGN 17E-A04: REPLACE EMISSIONS LABEL: Vehicles are non-compliant with emissions regulations (incorrectly labelled).
B110117
Service Bulletin/Repair Instructions
N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT: This SI provides a new tool and a new procedure for the N63TU valve seals replacement.
B611915
Service Bulletin/Repair Instructions
Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
B612817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F04B. One or several of the following check control messages (CCM) may be displayed: "Engine fault! Power loss" (CCM-ID: 29) "Powertrain malfunction!" (CCM-ID: 633) "Hybrid system malfunctioning!" (CCM-ID: 585) Note: The fault code 21F04B stated below may also be entered without any of the above mentioned CC messages being displayed A timing problem between the SME and the cell supervision circuit (CSC).
B640217
Service Bulletin/Repair Instructions
NOISE FROM A/C ON POWER-UP AND VENT SELECTION. When selecting a desired outlet vent combination and on power-up (resetting of previous vent selection) of the A/C air distribution system, a disturbing noise is heard (see video - tinyurl.com/y89pdvva). Contact between directional flaps and distributor housing
B120817
Service Bulletin/Repair Instructions
POWERTRAIN FAULTS DUE TO CHAFING OF ENGINE WIRING HARNESS. One or more of the following fault codes are stored in the DDE: 29FB00 - DeNOx system, warning and switching off scenario: Warning level 1 280D00 - NOx-Sensor upstream DeNOx-catalytic converter, signal NOx: NOx-Signal invalid for too long 280F00 - NOx-Sensor downstream DeNOx-catalytic converter, signal NOx: NOx-signal invalid for too long 29FC00 - DeNOx-system, warning and switch-off scenario: Warning level 2 CD840A - FA-CAN bus: Control unit switched off from bus (Bus off) CD94C7 - Message (RQ_PWR_EL_EPS, 234.0.2, FX): Messaging from EPS failed CD951C - Message (AVL_STMOM_DV_ACT_AVL_FORC_GRD, 49.0.2, FX):Messaging from EPS failed CD9536 - Message (DIAG_OBD_SCR, 0x3EE, FA): Messaging from SCR control unit failed CD953A - Message (ST_FFLV_SCRA, 0x40B, FA): Messaging from SCR control unit failed CD953C - Message (ST_RESO_SCRA, 0x8A, FA): Messaging from SCR control unit failed CD942B - Message (DT_GRDT, 0x1AF, A): Messaging from transmission control unit failed CD946B - Message (ST_GRB_ECU, 0x39A, FA): Messaging from transmission control unit failed CD9487 - Message (RQ_TORQ_CRSH_GRB, 0xB0, A): Messaging from transmission control unit failed CD94B9 - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Signal(s) in message invalid CD94BA - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Messaging from transmission control unit failed CD94C3 - Message (DIAG_OBD_GRB, 0x396, FA): Messaging from transmission control unit failed CD94DC - Transmission control unit, communication: Transmission communication via A- CAN and FACAN failed CD94ED - Message (DT_DISP_GRDT, 0x3FD, FA): Messaging from transmission control unit failed CD950D - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Signal(s) in message invalid ? CD950F - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Messaging from transmission control unit failed ? CD9549 - Message (DIENSTE-ID2=19 request MSA function, 0x598, FA): Message from transmitter control unit (EGS_EL) failed.
B610817
Service Bulletin/Repair Instructions
?General Electrical Systems Technical Service. VOLUNTARY EMISSIONS RECALL CAMPAIGN 17E-A01: CHECK CHARGING OF THE HIGH VOLTAGE BATTERY Bulletin type was changed from a Service Action to an Emissions Recall. High-voltage charging system may not work correctly. Alternative Mobility Solutions (AMS) Reimbursement This BMW Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement. Please refer to SI B01 29 16 for claim submission details. Intermittent hardware failure of the charging module (KLE).
B611417
Service Bulletin/Repair Instructions
MIL OR "POWERTRAIN MALFUNCTION!" CCM DISPLAYED IN INSTRUMENT CLUSTER. One or both of the following check control messages (CCM) is displayed: ? Malfunction indicator lamp (CCM-ID: 34) ? "Powertrain malfunction" (CCM ID: 633) Note: Depending on the driving situation, additional CCM(s) may also be displayed. Possible defect of the cell supervision circuit(s) (CSC).
B612617
Service Bulletin/Repair Instructions
Charging of the high voltage battery is interrupted and will not complete. A change in the job structure in ISTA causes the BDC to open the 30B relay unexpectedly.
B130315
Service Bulletin/Repair Instructions
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
B520716
Service Bulletin/Repair Instructions
LOSS OF SEAT ADJUSTMENT CONTROL. What is new? Procedure section updated with video link as a repair hint. Front seat electric adjustment controls do not function. Electrostatic discharge damage the seat module.
B610417
Service Bulletin/Repair Instructions
SLIGHT SHUDDERING UNDER ACCELERATION FROM 40-60MPH. When initiating gradual acceleration at between 40mph to 60mph, customer may experience some minor shuddering under acceleration. Some situations that may lead to this experience would be: Gradual depressing of the accelerator pedal Change in load (increase in road grade) Acceleration request by cruise control The following conditions must be present for this situation to occur: "Auto eDrive" driving mode selected Engine speed of approximately 1500 rpm Transmission in Drive, running in 7th or 8th gear, Low State of Charge (SOC) of high voltage battery. No fault codes are stored as a result of this performance issue. Stacking of tolerances in the driveline.
B611217
Service Bulletin/Repair Instructions
HV CHARGING INTERMITTENTLY NOT POSSIBLE. HV charging is intermittently not possible. When charging problem occurs, a CCM 804 Charging Not Possible" will be displayed. Affected vehicles may begin to charge if the charger plug is rapidly plugged/unplugged several times. Charging problem may be noticed consistently at same charging location, but not at others. KLE Software."
B611817
Service Bulletin/Repair Instructions
SME FAULT CODE 21F02A. Upon starting the vehicle, the following CC message is displayed to the customer: Powertrain malfunction!" (CCM-ID: 633) In addition, one or several of the following CC message(s) may be displayed: "Charging not possible" (CCM-ID: 804), "Hybrid system malfunctioning!" (CCM-ID: 585), "Drive. No restart" (CCM-ID: 586) or "Engine fault! Power loss" (CCM-ID: 29). Possible hardware defect of the safety box."
B650717
Service Bulletin/Repair Instructions
LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."
B510517
Service Bulletin/Repair Instructions
THUMP AT END OF REAR WINDOW TRAVEL . When opening, a loud thump is heard as the rear window reaches the bottom of its movement. Window guide.
B650616
Service Bulletin/Repair Instructions
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
B650617
Service Bulletin/Repair Instructions
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
B111715
Service Bulletin/Repair Instructions
?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 "Removing and installing/replacing upper oil sump" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. "All threads must be cleaned with screw tap" Or "Clean all threads with screw tap. Order number 81 43 0 402 559" Or "Clean all threads with a thread cutter". The current repair instruction terminology will be modified to include this information.
B112116
Service Bulletin/Repair Instructions
?CCM: "START/STOP FAILED": LOSS OF POWER . Malfunction Indicator Lamp (MIL) is illuminated Check Control Message (CCM) states "Auto Start/Stop function failed" One or more of the following codes may be stored in the DME fault memory' 120408: "Charging pressure control: switching off as a subsequent reaction" 130F20: "Exhaust camshaft: angular offset to crankshaft outside of tolerance" 130E20: "Intake camshaft: angular offset to crankshaft outside of tolerance" 164040: "Intake camshaft: Installation faulty" 164041: "Exhaust camshaft: Installation faulty" Incorrect camshafts timing position (in reference to crankshaft). Combustions occurring just as engine is stopping, drive the engine backwards, dragging the belt drive and toothed belt starter motor backwards. High-inertia torque loading on the camshaft sprockets and crankshaft at this point causes slippage, unintentionally adjusting the timing.
B180117
Service Bulletin/Repair Instructions
? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message "Drive faulty" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF.
B180310
Service Bulletin/Repair Instructions
? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The 10146535 20181105 B180310 20170201 Service Bulletin/Repair Instructions BMW 550I 2012 ENGINE AND ENGINE COOLING:EXHAUST SYSTEM ? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
B240117
Service Bulletin/Repair Instructions
?AUTOMATIC TRANSMISSION DRIVEABILITY COMPLAINTS . Hesitant drive off, sluggish driving behavior. The Automatic Transmission (AT) switches into emergency mode and operates only in first gear, Manual shifting (+/-) in Sport Program (using both gear selector and/or shift paddles) is not possible. 44E257 - "N6 speed sensor: Direction of rotation invalid" is stored in transmission control module Transmission Control Unit (GKEG3HY) software
B610317
Service Bulletin/Repair Instructions
CHANGE TO PHEV HV BATTERY CELL MODULES. INFORMATION There has been a change to all Generation 3 PHEV high-voltage (HV) battery cell modules. The number of temperatures sensors on the cell modules has decreased from 4 sensors to 3 sensors. This change has to be taken into account when replacing a component within the HV battery that requires the charging or discharging of a cell module with the Deutronic DBL1200HV-60 cell module charger. When connecting the cell module to the charger the number of temperature sensors (NTC's) will need to be changed to 3 for the charger to charge the module correctly. Refer to the DBL1200HV-60 manual for more information (Attached). To verify how many temperature sensors are on the cell module use the "Diagnosis" function of the DBL1200HV-60 cell module charger. The example to the right shows 3 temperature sensors. The message "ZKS not connected" will be displayed if the incorrect amount of temperature sensors (NTC's) is selected.
B630117
Service Bulletin/Repair Instructions
?SERVICE ACTION: TARGETED ILLUMINATION - REPROGRAM CONTROL UNITS . Affected vehicles need to have control units reprogrammed. CCM (Check Control Message) "Dynamic Light Spot has failed" for left or right side. Stepper motors in the targeted illumination headlights can become non-functional at their stop limit.
B000616
Service Bulletin/Repair Instructions
?June 2016 Maintenance and General Hints: technical Service Plugin Hybrids, (PHEV) MPGe Fuel Economy Rating.
B131015
Service Bulletin/Repair Instructions
?Emissions Recall Campaign 16E-A03. Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop.
B514816
Service Bulletin/Repair Instructions
?SERVICE ACTION: REAR SIDE WINDOWS MAY NOT BE PROPERLY AFFIXED TO BODY. Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop.
B612816
Service Bulletin/Repair Instructions
?SERVICE ACTION: CHECK CHARGING OF THE HIGH VOLTAGE BATTERY Please perform the procedure outlined in this Service Information on all affected vehicles prior to customer delivery, or the next time the vehicle is in the shop.
B612916
Service Bulletin/Repair Instructions
?MIL LAMP ILLUMINATED due to an internal fault in the EME. Replace EME.
B612416
Service Bulletin/Repair Instructions
SME FAULT CODE 21F21F. The fault code (FC) "21F21F - High-voltage system: Monitoring of insulation resistance deactivated due to fault of the safety box" is stored in the battery management electronics (SME). The fault does not set any CCM's, is not perceivable to the customer and has no effect on the complete vehicle operation. Safety box malfunction
B240616
Service Bulletin/Repair Instructions
FC 44E4D1 stored in Transmission Control Unit, either: 1. When no other fault codes stored. ? Customer has seen no performance issues. OR 2. When any of the following fault codes are stored. 44D141 - transmission monitoring: Clutch A and D implausible 44D0E1 - transmission monitoring: Clutch B implausible 44D191 - transmission monitoring: Clutch C and D implausible 44D151 - transmission monitoring: Clutch A and E implausible 44D0D1 - transmission monitoring: Clutch A implausible 44CFB1 - transmission monitoring: Clutch A, D and E implausible 44CFD1 - transmission monitoring: Fault pattern - gear monitoring implausible And possibly: ? Customer reports harsh shifting ? Check Control message "Drivetrain malfunction" Various
B640415
Service Bulletin/Repair Instructions
Third Row of Seats Blower is Inoperative. The blower in the third row of seats is not working and the fault code "E70C32 - AC-LIN: Heating in third row of seats is not responding" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective
B122316
Service Bulletin/Repair Instructions
SHUDDER OR JERKING IN 7TH AND 8TH GEARS AT 1000 - 1400 RPM. A shudder or slight jerking can be felt when driving with the transmission in 7th or 8th gear and the engine speed is between 1,000 and 1,400 RPM. No related faults are stored and there are not any problems in the chassis systems or with the wheels and tires. This shudder or jerking could begin due to the characteristic power pulses of the N63T engine when it is in VVT mode at low engine loads.
B340516
Service Bulletin/Repair Instructions
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
B652316
Service Bulletin/Repair Instructions
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
B652416
Service Bulletin/Repair Instructions
NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes "without a cash option" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes "without cash option". UPDATE Install new map data.
B662116
Service Bulletin/Repair Instructions
KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
B121816
Service Bulletin/Repair Instructions
CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
B180316
Service Bulletin/Repair Instructions
DDE FAULT CODE: 28DE00 - EXHAUST GAS PRESSURE SENSOR BEFORE TURBINE, PLAUSIBILITY. After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible
B611916
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON (MIL) - SME FC 21F20D. Malfunction Indicator Lamp (MIL) is illuminated. The following codes may be stored in the fault memory of the battery management electronics (SME). 21F20D - SME, safety concept: Switch-off of switch contactors by safety circuit 21F1F6 - High-voltage battery, switch contactors: Switch-off after a fault Software bug: erroneous fault code stored in SME.
B511615
Service Bulletin/Repair Instructions
Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a "Vehicle Comment" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2
B520416
Service Bulletin/Repair Instructions
NOISE FROM THE FRONT SEAT WHEN ENTERING / EXITING THE VEHICLE. The front seats generate a squeaking noise upon entering or exiting the vehicle. The noise may also occur when repositioning on the seat or movement while driving. Aged/dried leather on the seat bottom cushion rubbing against the plastic side trim.
B610916
Service Bulletin/Repair Instructions
Charging Not Possible - KLE Fault 21E715. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
B661816
Service Bulletin/Repair Instructions
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
B710216
Service Bulletin/Repair Instructions
INCORRECT TIRE AND LOADING INFORMATION LABEL. Five (5) vehicles were produced with an incorrect Tire and Loading Information label. The label may not reflect the proper "Cold Tire Pressure" specifications for the vehicle. AFFECTED VEHICLES Only the vehicles listed below are affected by this action: VINsMYModelCurrent Address State5UXKR0C5XF0K588942015X5 xDrive35iNew Jersey5UXKR0C57F0K588982015X5 xDrive35iFlorida5UXKR0C54F0K589072015X5 xDrive35iMassachusetts5UXKR0C58F0K589092015X5 xDrive35iNew York5UXKR0C5XF0K589132015X5 xDrive35iVirginia
B840516
Service Bulletin/Repair Instructions
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
B620516
Service Bulletin/Repair Instructions
Head-up Display is no Longer Visible. HUD (Head-up Display) adjusted to the lowest position is no longer visible. Software in the instrument cluster
B370214
Service Bulletin/Repair Instructions
Service Action: Program Variable Damper Control (VDC) Unit. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
B621016
Service Bulletin/Repair Instructions
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
B121416
Service Bulletin/Repair Instructions
Service Action: Program control units (DME data status). The high-voltage battery's life may be reduced when charging the high-voltage battery while the vehicle is in motion. AFFECTED VEHICLES Certain VINs (not all) produced between August 7, 2015 and April 19, 2016. Please check the key reader or the Warranty Vehicle Inquiry screen in DCSnet. The charging strategy incorporated in the DME software.
B170116
Service Bulletin/Repair Instructions
Delivery Stop - Transmission Oil Cooler Lines Incorrectly Routed. A Delivery Stop has been issued for fifteen F15 vehicles produced from March 3, 2016 to March 28, 2016. In these vehicles the cooler lines for the automatic transmission may have been routed incorrectly. In such instances, the cooler lines may come into contact with the crankshaft vibration damper (pulley). Affected vehicles can be identified with a "Vehicle Comment" in DCS Warranty Vehicle Inquiry or ISPA Light with the description: "A Delivery Stop has been issued for this vehicle. Dealers must ensure that all Campaigns are completed before retail delivery to the customer. See Service Information Bulletin B17 01 16."
B240116
Service Bulletin/Repair Instructions
F15, F30 PHEVs- Gear Selector Plausibility Faults. The Check Control message "Drive: Stop carefully" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function
B511216
Service Bulletin/Repair Instructions
Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
B611016
Service Bulletin/Repair Instructions
Charging Not Possible - KLE Fault 21E693. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
B620816
Service Bulletin/Repair Instructions
Incomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
B640516
Service Bulletin/Repair Instructions
Crackling Noise from the Fresh Air Grille This Service Information bulletin supersedes SI B64 05 16 dated March 2016.. Customer complains of crackling noises coming from the fresh air grille for approx. 15 seconds when switching on the air-conditioning system. Refrigerant transition inside the evaporator.
B651716
Service Bulletin/Repair Instructions
Airbag (SRS) Warning Lamp Illuminated. Airbag lamp (SRS) is illuminated and both of the following fault codes are stored: 930904 - Airbag driver stage 1: Resistance too large 93090A - Airbag driver stage 2: Resistance too large CAUSE Coil spring cassette damage.
B660916
Service Bulletin/Repair Instructions
"Collision Warning Failed" or "Pedestrian Warning Failed" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the "green lines"
TEC24
Service Bulletin/Repair Instructions
Tech24 Snap-in Adapter Return
B610616
Service Bulletin/Repair Instructions
CM "Engine fault! Power loss" and/or "Battery charging fault!". Upon unlocking or starting the vehicle, one or both of the following Check Control messages (CCM) are displayed to the customer: "Engine fault! Power loss" (CCM-ID: 29) "Battery charging fault!" (CCM-ID: 213). CAUSE Faults from Safety box (S-Box) in the high-voltage battery.
B840715
Service Bulletin/Repair Instructions
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
TEC26
Service Bulletin/Repair Instructions
TEC26 Turbo Charger Return
TEC25
Service Bulletin/Repair Instructions
Tec25 Wishbone Return
B640216
Service Bulletin/Repair Instructions
Humming/Buzzing Noise from Passenger Side Dashboard. There is a humming or buzzing sound from the passenger side dashboard. This noise only subsides when the entire heating and A/C system is shutoff. The A/C refrigerant shutoff valve is creating a harmonic sound which is resonating into the passenger compartment.
B650516
Service Bulletin/Repair Instructions
False Alarms of the Anti-Theft Alarm System. The alarm (DWA) siren continues to activate after locking vehicle An "unapproved" device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode.
B650716
Service Bulletin/Repair Instructions
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
B660416
Service Bulletin/Repair Instructions
"Comfort Access Restricted" Check Control Message is Displayed. "Comfort Access Restricted" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC
SIM010603
Service Bulletin/Repair Instructions
MINI "Enhanced" dealer self authorized (DSA)K goodwill program
SIM110115
Service Bulletin/Repair Instructions
MINI engine oil part number transition and model year 2016 engine oils
B120116
Service Bulletin/Repair Instructions
Under certain engine operating conditions the measured air mass between the cylinder banks 1-4 and 5-8 is miscalculated by the DME's. This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.
B130116
Service Bulletin/Repair Instructions
The DDE software application for exhaust gas recirculation control (EGR) does not favorably match the diesel fuel grades available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults being stored in the DDE.
B360115
Service Bulletin/Repair Instructions
SI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
B610314
Service Bulletin/Repair Instructions
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
B650216
Service Bulletin/Repair Instructions
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
B620116
Service Bulletin/Repair Instructions
Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement.
B621415
Service Bulletin/Repair Instructions
Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
B124615
Service Bulletin/Repair Instructions
Service Action: Program PHEV Control Units. The DME (Digital Motor Electronics) software is not sufficiently robust and may lead to sporadic fault code entries.
B540315
Service Bulletin/Repair Instructions
Sunroof Makes a Creaking Noise During Operation. When opening or closing the sunroof a creaking/ crackling type noise is heard. Insufficient lubrication of the sunroof guide rails
B123915
Service Bulletin/Repair Instructions
SI B12 39 15November 2015 Engine Electrical SystemsTechnical Service This Service Information Bulletin supersedes SI B12 39 15 dated November 2015.. The software in the Electrical Machine Electronics (EME) is incorrectly calibrated.
B612415
Service Bulletin/Repair Instructions
Charging Not Possible. The red Check Control message (CCM ID-804): "Charging not possible" is displayed. The following fault codes are stored: ? 21E600 - (KLE, Convenience Charging Electronics) - Charging socket, forceful disconnection of the charging plug detected ? 222834 - (EME, Electric Machine Electronics) - Charging not possible ? 222805 - (EME, Electric Machine Electronics) - Stopping of the charging hardware Electrical Machine Electronics (EME) software.
B620715
Service Bulletin/Repair Instructions
Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles "arriving" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed "prior" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2.
B621015
Service Bulletin/Repair Instructions
Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 "display backlighting and graphics PCB switched off" stored. Kombi software.
B660815
Service Bulletin/Repair Instructions
Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
B130715
Service Bulletin/Repair Instructions
N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the "engine stop" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE) and electronic steering (EPS) control units.
B270415
Service Bulletin/Repair Instructions
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
B270315
Service Bulletin/Repair Instructions
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
B122114
Service Bulletin/Repair Instructions
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
B122315
Service Bulletin/Repair Instructions
Reduced Engine Power with "Charging Pressure Too High" Faults Stored. When accelerating under certain conditions, the engine power may be reduced and a Check Control Message (CCM) "Drive Faulty; Drive at moderate speed" is displayed. The following charging pressure control fault is stored in the DME: ? Fault 120208: Exhaust camshaft sensor, signal: not plausible As a result, the engine power is reduced, and the following faults may also be set: ? Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked ? Fault 120908: Charging pressure control2: Switch-off, pressure build-up blocked CAUSE DME software error
B340814
Service Bulletin/Repair Instructions
Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
B611115
Service Bulletin/Repair Instructions
Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
B651015
Service Bulletin/Repair Instructions
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
31 01 12
Service Bulletin/Repair Instructions
CLICKING NOISES ARE COMING FROM THE FRONT AXLE WHEN DRIVING ON LOW SPEED. *MA
B360215
Service Bulletin/Repair Instructions
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
B640215
Service Bulletin/Repair Instructions
A/C Makes Unusual Whistling Noise from Center Vents. An unusual whistling noise can be heard coming from the center vent area for approximately15 seconds after the A/C is switched on. CAUSE Evaporator in the A/C system
B640314
Service Bulletin/Repair Instructions
A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
B160415
Service Bulletin/Repair Instructions
Service Action: Program Control Units (SCR). The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
B660115
Service Bulletin/Repair Instructions
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
B121615
Service Bulletin/Repair Instructions
N63T: Oxygen Sensor Internal Resistance Faults. The Service Engine Soon light comes on with either or both of the following faults stored in the DME memory: ? 12B701 - Oxygen sensor heating after catalytic converter, function: Internal resistance too high ? 12B801 - Oxygen sensor heating after catalytic converter 2, function: Internal resistance too high The engine operation and performance are not affected. The DME diagnosis for the post catalyst oxygen sensor(s) is too sensitive.
B540115
Service Bulletin/Repair Instructions
Water Leaking from Headliner. During and/or after heavy or prolonged rain, one or both of the situation(s) listed below may occur: ? Water leaks from various locations in the headliner. ? The footwell carpet is wet or soaked with water. Multiple root causes have been linked to this issue. One or more of the cause listed below may apply. The sunroof drain tube is: ? Not properly connected to the sunroof ? Twisted or kinked between the sunroof and where it exits the vehicle ? The sunroof drain is cut or torn above the headliner.
B840514
Service Bulletin/Repair Instructions
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
122114
Service Bulletin/Repair Instructions
SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
160215
Service Bulletin/Repair Instructions
SUBJECT Service Action: Program Control Units (SCR). An error in the calculation of the DEF line pressure by the SCR module software could occur at temperatures below 32°F/0°C. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
370214
Service Bulletin/Repair Instructions
SI B37 02 14February 2015 Special Suspension SystemsTechnical Service This Service Information bulletin supersedes SI 37 02 14 dated February 2015. Changes made to the B370214 attachment. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Program Variable Damper Control (VDC) Unit. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
370314
Service Bulletin/Repair Instructions
?SI B37 03 14February 2015 Special Suspension SystemsTechnical Service This Service Information bulletin supersedes SI 37 03 14 dated February 2015. Changes made to the B370314 attachment. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Program Variable Damper Control (VDC) unit. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new VDC software improves the acceleration sensor accuracy in our vehicles, and it helps us to ensure superior product quality. Please implement the VDC Programming Service Action immediately. This Service Action will be in effect until March 2015. Thank you for your continuous support. Unfavorable tolerances for the wheel acceleration sensors' plug-in connections may result in deactivation and fault code memory entries and the VDC. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
610314
Service Bulletin/Repair Instructions
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
613014
Service Bulletin/Repair Instructions
SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is "applicable" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
620115
Service Bulletin/Repair Instructions
SUBJECT Head-Up Display Information No Longer Visible. The Head-up Display information is no longer visible on the windshield. The Head-up Display has moved downwards to the lowest possible position and can no longer be adjusted to a higher position. Software error in the instrument cluster
650414
Service Bulletin/Repair Instructions
Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself.
120415
Service Bulletin/Repair Instructions
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
120915
Service Bulletin/Repair Instructions
SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the "fuel consumption, current" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold.
123814
Service Bulletin/Repair Instructions
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
161614
Service Bulletin/Repair Instructions
SI B16 16 14January 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B16 16 14 dated December 2014. designates changes to this revision SUBJECT Service Engine Soon Light (MIL) Is On with SCR Faults Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32°F / 0°C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. F25 (X3) only: z 8051B0 - Metering line heating, power too high SCR module software error
651312
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
652413
Service Bulletin/Repair Instructions
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.