B510819
Service Bulletin/Repair Instructions
The basic conditions for initializing the power windows are not met.
Vehicle report
2004 BMW Z4
Service bulletins
34 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
B611305
Service Bulletin/Repair Instructions
The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle âÂÂdischarged batteryâ complaints.
B662419
Service Bulletin/Repair Instructions
Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
B340414
Service Bulletin/Repair Instructions
Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
B110208
Service Bulletin/Repair Instructions
Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
513608
Service Bulletin/Repair Instructions
Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
B650709
Service Bulletin/Repair Instructions
NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
B360215
Service Bulletin/Repair Instructions
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
010914
Service Bulletin/Repair Instructions
?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho 10148018 20181113 010914 20140901 Service Bulletin/Repair Instructions BMW 335D 2009 EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL ?SI B01 09 14 September 2014 WarrantiesWarranties This Service Information bulletin supersedes SI B01 09 14 dated August 2014. Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho
610314
Service Bulletin/Repair Instructions
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
120913
Service Bulletin/Repair Instructions
State Inspection and Emission (I/M) Test Fails Due To an Invalid VIN Number. The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
641105
Service Bulletin/Repair Instructions
Clicking/Popping Noise from Dash at Startup. The customer states that when the vehicle is started, or the ignition switch is turned on, there is a clicking/popping noise coming from the dash area. CAUSE Mis-alignment of the fresh air/recirculation flap gears.
SIB-61-13-05
Service Bulletin/Repair Instructions
BMW: BATTERY HAS AN INCREASED DEMAND DUE TO DEVELOPEMENTAL PROCESS OF THE ELECTRICAL SYSTEM. THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB
SIB-65-75-06
Service Bulletin/Repair Instructions
BMW SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. THE AIRBAG WARNING LAMP (AWL) IS ILLUMINATED, TOGETHER WITH THE PASSENGER AIRBAG STATUS LAMP (POL). THE PROBLEM MAY BE INTERMITTENT. MICROCRACKS IN THE OC3 SEAT MAT. *PE UPDATED 9/30/11. *PE
SIB-33-01-02
Service Bulletin/Repair Instructions
BMW: A GRINDING NOISE IS COMING FROM THE DIFFERENTIAL DURING SLOW CORNERING. WHEN TURNING A SLIP/STICK EFFECT IS CREATED ON THE LINING AND STEEL DISCS INCORPORATED IN THE DIFFERENTIAL CLUTCH CAUSES A GRINDING NOISE. *RM
SIB-23-01-08
Service Bulletin/Repair Instructions
BMW: A NEW TECHNICAL SUPPORT PROCESS HAS BEEN CREATED REGARDING TRANSMISSION CONCERNS. *RM
SI B12 55 06
Service Bulletin/Repair Instructions
BMW: THERE MAY BE EXCESSIVE CRANKING BEFORE THE VEHICLE STARTS. THE SERVICE ENGINE SOON LIGHT MAY ALSO BE ON WITH A LACK OF ENGINE POWER. *RM
SI-B-12-04-05
Service Bulletin/Repair Instructions
BMW: CHECK ENGINE LAMP ILLUMINATED AND/OR VEHICLE OVERHEATS. MODELS E83, E85, E86, E70, E90, E91, E92, E93, E60 AND E61. *PE UPDATED 5/24/11. *PE
SIB-51-42-10
Service Bulletin/Repair Instructions
BMW: WATER IS LEAKING INTO THE LUGGAGE COMPARTMENT DUE TO A DAMAGED SEAL ON REAR VENTS. *RM
SIB-63-14-10
Service Bulletin/Repair Instructions
BMW: THE REAR LAMP IS NOT WATER TIGHT DUE TO CRACKS DUE TO STRESS. WATER MAY ENTER THE LAMP. *RM
SIB-63-02-01
Service Bulletin/Repair Instructions
BMW: PROCEDURE FOR DETERMINING AND REPLACING INCANDESCENT AND HALOGEN LIGHT BULBS UNDER WARRANTY. *RM
SI B12-55-06
Service Bulletin/Repair Instructions
N54-DIAGNOSIS FOR DME FC 29DC/2FBF FOR MODELS E90, E92 PRODUCED FROM 06/06 AND E93, E60, E61 PRODUCED FROM 03/07. *PE UPDATED 7/8/09. *PE MODELS E82, E88 PRODUCED FROM START 2000 AND E71 PRODUCED FROM START 2000. UPDATED 7/21/10. *PE MODELS X6, E89, Z4 FROM START OF PRODUCTION. UPDATED 11/1/10. *PE MODELS F01 AND F02 FROM START OF PRODUCTION. UPDATED 1/3/11. *PE
SIB-11-08-03
Service Bulletin/Repair Instructions
BMW: SIX DIFFERENT MODELS EQUIPPED WITH THE M54 ENGINE COULD HAVE VALVE COVERS BREAK IN COLD WEATHER AND RUIN THE ENGINE. THIS IS DUE TO MOISTURE ACCUMULATION. *RM
SI B12 12 10
Service Bulletin/Repair Instructions
BMW: WHEN AT LOWER SPEEDS OR STOPPING THE ENGINE IDLE DIPS TOO LOW BECAUSE OF A SOFTWARE PROBLEM. *RM
SIB-28-02-08
Service Bulletin/Repair Instructions
BMW: A NEW TECHNICAL PROCESS IS BEING USED ON MANY MODELS TO DETERMINE THE ROOT CAUSE OF DOUBLE-CLUTCH TRANSMISSION PROBLEMS. *RM
SIB-32-04-07
Service Bulletin/Repair Instructions
BMW: A NEW TECHNICAL PROCESS HAS BEEN CREATED FOR BMW TO IDENTIFY CAUSES OF STEERING COMPLAINTS WITH A WIDE RANGE OF MODELS. *RM
SIB-16-02-09
Service Bulletin/Repair Instructions
BMW VEHICLES: FUEL LEVEL SENSOR REPAIRS. WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE
SI-B-34-11-08
Service Bulletin/Repair Instructions
BMW VEHICLES: TEILECLEARING FOR DYNAMIC STABILITY CONTROL (DSC). A PART REPLACEMENT AUTHORIZATION MUST BE OBTAINED BY SUBMITTING A TC CASE IN PUMA BEFORE ANY OF THE FOLLOWING DSC COMPONENTS ARE REPLACED UNDER WARRANTY FOR THE VEHICLES LISTED IN THE MODEL SECTION OF THIS BULLETIN: DSC CONTROL MODULE, DSC HYDRO UNIT, AND YAW RATE SENSOR. NO MODEL YEARS LISTED. *PE
SI-B72-02-09
Service Bulletin/Repair Instructions
BMW: BELT TENSIONER HARNESSES. A REPAIR HARNESS FOR THE FRONT SEAT SAFETY BELT TENSIONERS AT THE BELT RETRACTORS MAY HAVE BEEN IMPROPERLY INSTALLED. *PE
SIB-12-20-07
Service Bulletin/Repair Instructions
BMW VEHICLE: M54/M56-MIXTURE TOO LEAN-FAULT CODES 2882/2883 ARE STORED IN THE DME. COMPLAINTS THAT SERVICE ENGINE SOON LIGHT IS ILLUMINATED. THE FAULT CODES 2882/2883-FUEL TRIM, MIXTURE TOO LEAN ARE STORED IN THE DME. POSSIBLE CAUSES MAY INCLUDE-INCORRECT AIR FILTER, UNMETERED AIR OR A DEFECTIVE AIR MASS METER. *PE
SIB-12-24-07
Service Bulletin/Repair Instructions
BMW VEHICLE: S54-CATALYST PROTECTION MODE WHILE THE VEHICLE IS LOW ON FUEL. COMPLAINTS THAT THE VEHICLE HAS NO POWER DURING HEAVY ACCELERATION. FUEL RESERVE LIGHT IS ILLUMINATED AND THE FUEL LEVEL, WHEN MEASURED WITH THE SERVICE TESTER, IS BELOW 10 LITERS. WITH THE FUEL LEVEL LOW AND UNDER EXTREME DRIVING CONDITIONS (HEAVY ACCELERATION, CORNERING OR RACING), THE FUEL SUPPLY MAY BE INADEQUATE, CAUSING AN INTERMITTENT LEAN MIXTURE TO BE RECORDED BY ALL 4 OXYGEN SENSORS. *PE
04V182
Service Bulletin/Repair Instructions
RECALL CAMPAIGN 04V-182 ENGINE STALLING. CORRECTED PRODUCTION DATES. *TT
041904
Service Bulletin/Repair Instructions
RECALL CAMPAIGN 04V182 - ENGINE STALLING. CORRECTION PRODUCTION DATES. *TT
121104
Service Bulletin/Repair Instructions
RETROFIT THE POWER SUPPLY CABLE FOR THE THERMAL OIL LEVEL SENSOR. *EH
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.