PIP5601C
Service Bulletin/Repair Instructions
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Vehicle report
2002 BUICK LESABRE
Service bulletins
362 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
23-NA-001
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
PIP5358D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP4723J
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5099H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
General Communication
Service Campaign
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
24-NA-141
Service Bulletin/Repair Instructions
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
16-NA-383
Service Bulletin/Repair Instructions
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
10-08-45-001H
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
22-NA-074
Service Bulletin/Repair Instructions
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
02-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
Service Bulletin/Repair Instructions
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
23-NA-219
Service Bulletin/Repair Instructions
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
17-NA-170
Service Bulletin/Repair Instructions
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
10-00-89-006J
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
23-NA-153
Service Bulletin/Repair Instructions
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
18-NA-073
Service Bulletin/Repair Instructions
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5628G
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5358C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
19-NA-219
Service Bulletin/Repair Instructions
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
22-NA-009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5540J
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
22-NA-205
Service Bulletin/Repair Instructions
This service bulletin provides information on Module Harvesting.
10-00-89-006I
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
Service Bulletin/Repair Instructions
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
22-NA-181
Service Bulletin/Repair Instructions
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
20-NA-065
Service Bulletin/Repair Instructions
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5099F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
3249
Service Bulletin/Repair Instructions
HIGH SPEED SHAKE OR VIBRATION. *EH
PIP5358B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP4723F
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
PIT3099U
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
21NA124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
100089006H
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIP5628C
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5453C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5628B
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
16NA383
Service Bulletin/Repair Instructions
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIT3099T
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
19NA273
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Procedures to Unlock Delco Radio with Theftlock.
100089009D
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
PIC4696E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable. E version update is to add administrative details.
010842001M
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
100089006G
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
100089009C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
17NA073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIC4696D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable.
PIT3099S
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT3099R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
100845001G
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
PIP5640
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
100845001F
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP5540D
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
17NA170
Service Bulletin/Repair Instructions
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
010842001L
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
Service Bulletin/Repair Instructions
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
Service Bulletin/Repair Instructions
This Preliminary information communicates
PIT5099D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5099C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC4696C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco Theft Lock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIT5399A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5338B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP5226B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5540A
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5540
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5353B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP4723C
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-06-01-012G
Service Bulletin/Repair Instructions
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
15-08-44-001I
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
Service Bulletin/Repair Instructions
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
10-00-89-006F
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report.
PIT5389C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
17-NA-016
Service Bulletin/Repair Instructions
This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.
03-08-46-004S
Service Bulletin/Repair Instructions
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5492E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT3099N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5453B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. THE GENERAL MOTORS OF CANADA CUSTOMER CARE CENTRE IS THE SOLE AUTHORIZED PROVIDER OF A CERTIFICATION CONFIRMATION LETTER WHICH HELPS OUR CUSTOMERS IDENTIFY IF THEIR VEHICLES MEETS THE REQUIRED USA REGULATORY STANDARDS NECESSARY FOR IMPORTATION INTO THE USA.
PIC5491J
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
Service Bulletin/Repair Instructions
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
000601012F
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
PIP5094A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIT-5485-B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC5088F
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC-4935-E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
Service Bulletin/Repair Instructions
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5484A
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIC5953A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
02-08-42-001I
Service Bulletin/Repair Instructions
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
Service Bulletin/Repair Instructions
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
PIP5226A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
01-08-42-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
PIT4720D
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
16-NA-025
Service Bulletin/Repair Instructions
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
Service Bulletin/Repair Instructions
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIC6140B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT5353A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5484
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT5486
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT4943D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC4696B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
15-NA-079
Service Bulletin/Repair Instructions
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIC6140A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIC4696A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIC5953B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5464
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
09-09-40-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIC6107
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6101
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIT5384A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
05-06-04-035E
Service Bulletin/Repair Instructions
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
02-08-42-001H
Service Bulletin/Repair Instructions
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
PIT5399
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
05-08-46-006T
Service Bulletin/Repair Instructions
This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.
15-08-44-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PIT5264C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
10-08-45-001E
Service Bulletin/Repair Instructions
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
PI1394
Service Bulletin/Repair Instructions
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIC3278F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
030848006J
Service Bulletin/Repair Instructions
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
PIT5353
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5029F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT5264B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
Service Bulletin/Repair Instructions
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
PIT5099A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5232A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5264A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIC6036
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-00-89-006E
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
PIT3099M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
Service Bulletin/Repair Instructions
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
PIP5163A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
Service Bulletin/Repair Instructions
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
10-00-89-006D
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
Recalls
Service Bulletin/Repair Instructions
Vehicle Recalls
PIC5088E
Service Bulletin/Repair Instructions
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
05-08-46-006S
Service Bulletin/Repair Instructions
This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.
05-06-04-035D
Service Bulletin/Repair Instructions
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
Service Bulletin/Repair Instructions
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
PIT3099L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1217
Service Bulletin/Repair Instructions
This preliminary bulletin provides a way to aid the technician in diagnosing transmission fluid leaking from the trans breather vent.
PIT5264
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIT4864F
Service Bulletin/Repair Instructions
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
PIT4943C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
99-08-51-007F
Service Bulletin/Repair Instructions
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PI0281D
Service Bulletin/Repair Instructions
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
Service Bulletin/Repair Instructions
This informational bulletin provides directions on submitting different PIRs
05-00-89-072C
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
PIP5163
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5913
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Supplemental Inflatable Restraint lamp, Service Vehicle Soon lamp on and/or radio locked, possibly after module replacement. Technician will need to check for an incorrect or non-existent VIN number in modules that require them. Technician should ensure that all modules that are replaced are programmed per currently published Service Information. Technician should also check the Sensing and Diagnostic Module part number if it was replaced.
PIT3099K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130089009
Service Bulletin/Repair Instructions
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIC5904
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
10-00-89-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
08-06-01-006D
Service Bulletin/Repair Instructions
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
05-08-48-001C
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
PIT4720C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
13-00-89-005
Service Bulletin/Repair Instructions
This technical bulletin provides Warranty Administration - New Labor Codes information.
99-04-20-002H
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
11-00-89-005D
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
00-03-10-002G
Service Bulletin/Repair Instructions
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
PIP3140E
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
08-08-51-002A
Service Bulletin/Repair Instructions
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
11-00-89-005C
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIC3718E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
080846004A
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
000089027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
100089010B
Service Bulletin/Repair Instructions
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
010089010J
Service Bulletin/Repair Instructions
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
PIT4907A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIC4935D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIT3099J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
11-00-89-005B
Service Bulletin/Repair Instructions
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
PIC5588A
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
09-09-40-001A
Service Bulletin/Repair Instructions
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
SB-10-08-50-003B
Service Bulletin/Repair Instructions
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
050861002
Service Bulletin/Repair Instructions
FLOOR PAN CORROSION PERFORATION IN BATTERY COMPARTMENT. *TT UPDATE. *TT UPDATED ON 06/30/2011. *KB
08089-B
Service Bulletin/Repair Instructions
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
08-089B
Service Bulletin/Repair Instructions
BUICK CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. CSC LETTER WAS RECEIVED. *PE
08-089
Service Bulletin/Repair Instructions
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
PIC-4887
Service Bulletin/Repair Instructions
GMC: HARSH RIDE OR LINE INSTALLATION CONCERN WITH DELCO SHOCK KIT. CONCERNS WITH CONNECTING THE LINES TO THE SHOCKS AND THE AIR COMPRESSOR. CONCERN OF HARSH RIDE AFTER INSTALLATION. *PE
080730002
Service Bulletin/Repair Instructions
INFORMATIONAL ON 4T65-E MN7, M15 AND M76 FRONT WHEEL DRIVE AUTOMATIC TRANSMISSION VALVE BODY RECONDITIONING, DTCS P0741, P0742, P0757, P842, HARSH SHIFTS OR SLIPS. *PE
030604030
Service Bulletin/Repair Instructions
MULTIPLE DRIVEABILITY SYMPTOMS OF LONG OR HARD STARTS, CHUGGLE, ROUGH IDLE AND LIGHT OR INTERMITTENT MISFIRE DUE TO CLOGGED FUEL INJECTORS. *TT
050604058
Service Bulletin/Repair Instructions
INTERMITTENT CHUGGLE OR FISHBITE ON LIGHT ACCELERATION OR A HIGHWAY SPEEDS WITH NO DIAGNOSTIC TROUBLE CODES (DTCS). *TT
709
Service Bulletin/Repair Instructions
CAR ISSUES - FIX IT RIGHT THE FIRST TIME (NEW ISSUES IN BOLD). TO INCLUDE 2006 AND 2007 MODELS. GM. TECH LINK. *TT
050864011
Service Bulletin/Repair Instructions
FRONT DOOR WINDOW BINDS/INOPERATIVE/MOVES SLOWLY. *TT
030848005A
Service Bulletin/Repair Instructions
COMPASS ZONE ADJUSTMENT AND CALIBRATION PROCEDURE DURING PRE-DELIVERY INSPECTION. VARIOUS MODELS INCLUDING 2002-2004 LIGHT DUTY TRUCKS. *TT UPDATE TO INCLUDE 2005 BUICK ALLURE. *TT
050850003
Service Bulletin/Repair Instructions
HEATED SEAT INOPERATIVE AFTER REPAIR WITHIN ONE WEEK OF USAGE. *TT
040861001
Service Bulletin/Repair Instructions
FLOOR PAN CORROSION PERFORATION IN BATTERY COMPARTMENT. *EH
611
Service Bulletin/Repair Instructions
TIRE PRESSURE MONITOR RESET/LEARN-WHEN THE PRESSURE IN THE AFFECTED TIRE WAS SET TO SPECIFICATION ON SOME VEHICLES, THE CHECK TIRE PRESSURE AND OR XX TIRE HIGH/LOW DISPLAY IS CANCELED WITHIN 20 SECONDS OF THE PRESSURE ADJUSTMENT. *SC
040139005
Service Bulletin/Repair Instructions
NOISY BLOWER MOTOR. *SC
040849022
Service Bulletin/Repair Instructions
CENTER CONSOLE ARMREST LID LATCH NOW AVAILABLE FOR SERVICE. *EH
0804
Service Bulletin/Repair Instructions
OIL LIFE SYSTEM RESET PROCEDURES - CARS. *NM
040601017
Service Bulletin/Repair Instructions
NEW UPPER INTAKE MANIFOLD AND GASKET KITS. *TT
040601021
Service Bulletin/Repair Instructions
NEW REAR MAIN SEAL AND SPECIAL TOOL FOR INSTALLATION. *TT
040604023
Service Bulletin/Repair Instructions
POWERTRAIN CONTROL MODULE WILL NOT PROPERLY COMMUNICATE ON BOARD DIAGNOSTIC EGR TEST RESULT INFORMATION TO NON-TECH2 SERVICE OR TEST EQUIPMENT. *EH
040604024
Service Bulletin/Repair Instructions
POWERTRAIN CONTROL MODULE WILL NOT PROPERLY COMMUNICATE ON BOARD DIAGNOSTIC FREEZE FRAME INFORMATION TO NONTECH2 SERVICE OR TEST EQUIPMENT. *EH
01940
Service Bulletin/Repair Instructions
SEAT CLUNK OR NOISE. *MR *TT
03232004
Service Bulletin/Repair Instructions
THIS IS A FIX IT RIGHT THE FIRST TIME REMINDER GOING OUT TO BUICK DEALERS REGARDING ASHTRAYS THAT ARE EITHER DIFFICULT TO OPEN OR WILL NOT STAY CLOSED. *TT
000310007E
Service Bulletin/Repair Instructions
SHAKE/VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT UPDATE. *TT
020730013
Service Bulletin/Repair Instructions
INCORRECT TRANSMISSION SHIFTS, POOR PERFORMANCE OF ENGINE, TRANSMISSION SLIPPING, SES LAMP ILLUMINATED, DIAGNOSTIC TROUBLE CODES P0756 AND P0757. *SLC UPDATE. *TT
990603009A
Service Bulletin/Repair Instructions
FLOOR PAN CORROSION PERFORATION IN BATTERY COMPARTMENT. *TT UPDATE *EH
00372D
Service Bulletin/Repair Instructions
ONSTAR SYSTEM IS ATTEMPTING AND/OR COMPLETING PHONE CALLS WHICH THE OPERATOR OF THE VEHICLE DID NOT INITIATE. *TT
01353
Service Bulletin/Repair Instructions
ENGINE MISFIRE DUE TO INJECTOR FRETTING CORROSION. *TT
01534
Service Bulletin/Repair Instructions
TOO MUCH AIRFLOW COMING FROM THE VENTS WHEN THE BLOWER FAN SPEED IS IN THE LOW POSITION. SIT BULLETIN 1408545. *TT
01536
Service Bulletin/Repair Instructions
ALTERNATOR WHINE AFTER BULLETIN 99-06-03-005. SIT BULLETIN 1408812. *TT
02038
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE B1000. *MR
02118
Service Bulletin/Repair Instructions
DRONING SOUND FROM HVAC BLOWER SYSTEM. SERVICE VME. *MJ
02141
Service Bulletin/Repair Instructions
REPEAT ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT WITH DIAGNOSTIC TROUBLE CODE (DTC) C1225. VARIOUS MODELS INCLUDING 2005 CADILLAC DEVILLE. *TT
3007
Service Bulletin/Repair Instructions
3.8L ENGINE OIL CONSUMPTION. *TT
3011
Service Bulletin/Repair Instructions
WHEN USING VOICE RECOGNITION DIALING, SOME NUMBERS OR COMMANDS MAY NOT BE UNDERSTOOD BY THE SYSTEM ESPECIALLY THE NUMBER TWO (2). *TT
3015
Service Bulletin/Repair Instructions
MULTIPLE STABILITRAK/PRECISION CONTROL CODES SUCH AS C1282, C1283, C1284, C1285, C1287, AND C1288 EXIST ON DELPHI BOSCH 5.0 OR 5.3 SYSTEMS. *TT
3027
Service Bulletin/Repair Instructions
INSTRUMENT PANEL ITCH/CREAK. SERVICE VME. *TT
3047
Service Bulletin/Repair Instructions
99 THROUGH 05 YEAR VEHICLES, EQUIPPED WITH THREE-BUTTON ONSTAR SYSTEMS. *TT
3050A
Service Bulletin/Repair Instructions
02-05 ONSTAR EQUIPPED VEHICLES EMITTING BEEPING NOISE BEFORE CONNECTING TO ONSTAR. *TT
3052
Service Bulletin/Repair Instructions
BREAKPOINTS FOR RELEASE 5 FOR THE F1 (GEN 5) EQUIPPED PRODUCTS. *TT
3059
Service Bulletin/Repair Instructions
WHEN USING ONSTAR PERSONAL CALLING FEATURE, THE CALLER CANNOT BE HEARD ON OUTBOUND CALL ONLY. *TT
3095
Service Bulletin/Repair Instructions
WATER LEAK ON THE LEFT FRONT OR REAR FLOOR. *SC
00103A
Service Bulletin/Repair Instructions
WHEEL COVER NOISE RATTLE. *TT
00222A
Service Bulletin/Repair Instructions
UNEVEN RIGHT FRONT BRAKE WEAR WITH THE RIGHT FRONT OUTBOARD PAD BEING WORN AN AMOUNT INCONSISTENT WITH THE REST OF THE FRONT BRAKE PADS. *TT
00704A
Service Bulletin/Repair Instructions
THE 4T65E AUTOMATIC TRANSMISSION MAY EXHIBIT A CONDITION OF A HARSH GARAGE SHIFT INTO REVERSE OR DRIVE ON A COLD START. *TT
01468
Service Bulletin/Repair Instructions
THE IPM CANNOT BE LOCATED WITH MANUAL HVAC SYSTEM. *TT
11052003
Service Bulletin/Repair Instructions
ELECTRICAL CONCERNS IN THE INSTRUMENT PANEL AREA. *TT
030232049
Service Bulletin/Repair Instructions
RELEASE OF NEW OUTER TIE ROD ENDS FOR SERVICE. *TT
020730022B
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT
030604056
Service Bulletin/Repair Instructions
INFORMATION ON NEW THROTTLE BODY GASKET. *TT
510
Service Bulletin/Repair Instructions
ASHTRAY REPAIR SPRING-IN SOME CASES, THE ASHTRAY WAS BUILT WITH TWO SAME-SIDE SPRINGS WHICH MAY DEFORM CAUSING THE ASHTRAY TO HANG UP. *SC
030848005
Service Bulletin/Repair Instructions
COMPASS ZONE ADJUSTMENT AND CALIBRATION PROCEDURE DURING PRE-DELIVERY INSPECTION. *TT
010235009A
Service Bulletin/Repair Instructions
STEERING COLUMN TO INSTRUMENT PANEL FASTENER REMOVAL. *TT
030236002
Service Bulletin/Repair Instructions
REVISED STEERING WHEEL POSITION SENSOR OR STEERING SHAFT LOWER BEARING REPLACEMENT PROCEDURE AND STEERING WHEEL POSITION SENSOR CENTERING PROCEDURE. *EH
03019
Service Bulletin/Repair Instructions
ENGINE COOLANT MAY LEAK AT THE UPPER INTAKE MANIFOLD THROTTLE BODY GASKET, OR AT THE UPPER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD GASKET. THIS CONDITION MAY RESULT IN A LOW ENGINE COOLANT LEVEL AND HIGHER ENGINE OPERATING TEMPERATURES. *TT THIS IS A PARTS BULLETIN AND REFERS TO CUSTOMER SATISFACTION PROGRAM BULLETIN #03034. *TT
03034
Service Bulletin/Repair Instructions
ENGINE COOLANT MAY LEAK AT THE UPPER INTAKE MANIFOLD THROTTLE BODY GASKET, OR AT THE UPPER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD TO LOWER INTAKE MANIFOLD GASKET. THIS CONDITION MAY RESULT IN A LOW ENGINE COOLANT LEVEL AND HIGHER ENGINE OPERATING TEMPERATURES. *TT
57
Service Bulletin/Repair Instructions
WIRE HARNESS MAY BE STRETCHED, OR THE PCS MAY NOT BE ORIENTED IN THE SAME POSITION, AFTER INSTALLING A SERVICE REPLACEMENT VALVE BODY ASSEMBLY. GM TECH LINK. *TT
010846002C
Service Bulletin/Repair Instructions
PROGRAMMING OF REPLACEMENT ONSTAR VEHICLE COMMUNICATION AND INTERFACE MODULES (VCIM). *TT
030601016
Service Bulletin/Repair Instructions
LOSS OF COOLANT, MILKY COLORED OIL. *TT
030730017
Service Bulletin/Repair Instructions
GRIND NOISE OR NO VEHICLE MOVEMENT WHEN SHIFTING INTO DRIVE OR REVERSE. *TT
030850012
Service Bulletin/Repair Instructions
CUPHOLDER ASSEMBLY AND REPLACEMENT PROCEDURE AVAILABLE FOR FRONT SEAT STORAGE ARMREST. *TT
010851004A
Service Bulletin/Repair Instructions
PREMATURE ALUMINUM HOOD CORROSION / BLISTERING. *TT
01432
Service Bulletin/Repair Instructions
AUTOMATIC TRANSMISSION POOR ACCELERATION, PERFORMANCE. *TT
030849016
Service Bulletin/Repair Instructions
ASHTRAY DIFFICULT TO OPEN OR WILL NOT STAY CLOSED. *TT
11212002
Service Bulletin/Repair Instructions
FUEL TANK VAPOR VALVE. *EH
010850012A
Service Bulletin/Repair Instructions
FRONT HEATED SEAT INOPERATIVE / COLD. *TT
020850009
Service Bulletin/Repair Instructions
FRONT SEATS UNCOMFORTABLE/HARD IN LUMBAR AREA. *TT
000866003A
Service Bulletin/Repair Instructions
REAR COMPARTMENT SEAT BACK TRIM PANEL ATTACHMENT ARMS / STRAPS SAG OR TRIM PANEL IS LOOSE. *TT
020730022A
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT
000310007C
Service Bulletin/Repair Instructions
SUBJECT REGARDING SHAKE / VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT
220702
Service Bulletin/Repair Instructions
ENGINEERING IS IN THE PROCESS OF TESTING A NEW ADHESIVE FOR CUSTOMER COMPLAINTS THAT THE TRUNK INTERIOR CLOSEOUT PANELS ARE FALLING DOWN. *TT
160702
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXPERIENCE A CONDITION WHERE THE CLOSEOUT PANEL INSIDE THE TRUNK, BETWEEN THE TRUNK AND THE REAR SEAT, MAY FALL DOWN. *TT
000730002B
Service Bulletin/Repair Instructions
CONCERNS WITH SLIPS, HARSH UPSHIFT OR GARAGE SHIFTS, LAUNCH SHUDDERS, FLARES, ERRATIC SHIFTS AND INTERMITTENT CONCERNS, DIAGNOSTIC TROUBLE CODE P1811 OR P0748 SET. *TT
020730014A
Service Bulletin/Repair Instructions
INFORMATION ON SERVICING 4T65-E TRANSAXLE SPACER PLATE AND GASKETS FOR VARIOUS MODELS FROM 1997 THROUGH 2002. *TT
210602
Service Bulletin/Repair Instructions
BRIEF INFORMATION REGARDING DISTORTED / OVERHEATED TAIL LAMP LENS. *TT
180602
Service Bulletin/Repair Instructions
BRIEF SERVICE INFORMATION REGARDING THE ANTILOCK BRAKE LIGHT COMING ON AND MULTIPLE CODES SET. *TT
00310007B
Service Bulletin/Repair Instructions
TECHNICAL INFORMATION REGARDING SHAKE / VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT
020850006
Service Bulletin/Repair Instructions
SUBJECT REGARDING FRONT SEAT BACK SQUEAK. *TT
051302
Service Bulletin/Repair Instructions
SUBJECT REGARDING ISSUES WITH THE PS3 BASE WHEEL COVERS. *TT
020730002
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE SERVICE ENGINE SOON (SES) INDICATOR IS ILLUMINATED AND THAT WHILE THE LIGHT IS ILLUMINATED, TRANSMISSION SHIFTS ARE EXTREMELY HARSH. *TT
020846005
Service Bulletin/Repair Instructions
SUBJECT REGARDNG THE ADDITION OF DIAGNOSTIC TROUBLE CODE U1500 FOR GENERATION 4 ONSTAR. *TT
041502
Service Bulletin/Repair Instructions
ON VEHICLES EQUIPPED WITH THE DE150 DUAL PLAY RADIO, IT IS POSSIBLE TO LOSE THE CASSETTE AUDIO WHEN THE IGNITION KEY IS CYCLED FROM THE OFF POSITION TO THE ACCESSORY POSITION THEN BACK TO OFF AND BACK TO ACCESSORY. *TT
020730014
Service Bulletin/Repair Instructions
INFORMATION ON SERVICING 4T65E TRANSAXLE SPACER PLATE AND GASKETS. *TT
020730015
Service Bulletin/Repair Instructions
SUBJECT REGARDING REVISED DIAGNOSTIC TROUBLE CODE P0713. *TT
010202
Service Bulletin/Repair Instructions
POWER STEERING FLUID LEAKS IN THE RACK AREA. *TT
020864003
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT THAT THE OUTSIDE REARVIEW MIRRORS DO NOT RETURN TO THE MEMORY RECALL POSITION WHEN THE REMOTE KEYLESS ENTRY DOOR UNLOCK BUTTON IS USED. *SLC
211101
Service Bulletin/Repair Instructions
INFORMATION ON KEY FOBS. *TT
141101
Service Bulletin/Repair Instructions
CONCERNS WITH RATTLE NOISE OR SQUEAK IN THE FRONT OF THE INSTRUMENT PANEL CLUSTER AREA. *TT
081101
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXHIBIT A DIAGNOSTIC TROUBLE CODE AFTER INSTALLING A REPLACEMENT ABS EBCM. *TT
000604037A
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMPLAIN THAT THE SERVICE ENGINE SOON (SES) INDICATOR IS ILLUMINATED WITH HARSH TRANSMISSION SHIFTS. *TT
010847002
Service Bulletin/Repair Instructions
INFORMATION REGARDING BACKLIGHTING ON DRIVER AND PASSENGER DOOR SWITCHES REMAINS ON, HIGH PARASITIC CURRENT DRAW OCCURS. *YH
010849016
Service Bulletin/Repair Instructions
VEHICLES MAY EXPERIENCE AN INOPERATIVE CIGARETTE LIGHTER. *SLC
000310007A
Service Bulletin/Repair Instructions
INFORMATION REGARDING SHAKE/VIBRATION IN STEERING WHEEL, FLOOR,SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS (DIAGNOSE/BALANCE TIRES/WHEELS). *YH
010847001
Service Bulletin/Repair Instructions
INFORMATION REGARDING RIDE HEIGHT APPEARS LOW WITH REAR OF VEHICLE LOADED/ELECTRONIC LEVEL CONTROL DOES NOT OPERATE PROPERLY. *YH
010850012
Service Bulletin/Repair Instructions
INFORMATION REGARDING THE FRONT HEATED SEAT BEING INOPERATIVE. *YH
030801
Service Bulletin/Repair Instructions
VEHICLES MAY EXPERIENCE A CONDITON WHERE THE PLASTIC PANEL BEHIND THE REAR SEAT INSIDE THE TRUNK IS LOOSE OR HAS FALLEN INTO THE TRUCK. *YH
020701
Service Bulletin/Repair Instructions
INFORMATION REGARDING DOOR LEAK. *YH
0208701
Service Bulletin/Repair Instructions
INFORMATIION REGARDING A SQUEAK OR ITCH TYPE NOISE COMING FROM THE GLOVE BOX AREA. *YH
4T65E
Service Bulletin/Repair Instructions
INFORMATION REGARDING AUTOMATIC TRANSMISSION TORQUE CONVERTER OIL SEAL, A REQUEST FOR INFORMATION. *SLC
00112A
Service Bulletin/Repair Instructions
POPPING NOISE IN THE FOOTWELL AREA. *TT
3102
Service Bulletin/Repair Instructions
SERVICE VME 01-04 VEHICLE EQUIPPED WITH 4T65E AUTOMATIC TRANSMISSION 4T65E TRANSMISSION VALVE BODY INSPECTION PROCEDURE. (TO INCLUDE 2004 PONTIAC AZTEC) *SC ALL 2001 - 2006 PASSENGER VEHICLES WITH 4T65E TRANSAXLE. *TT
3157A
Service Bulletin/Repair Instructions
ENGINE WHINE OR BUZZ NOISE SOUNDS LIKE A GENERATOR TYPE NOISE ON 3.1L OR 3.8L ENGINES. *TT
3253A
Service Bulletin/Repair Instructions
HEATED SEAT INOPERATIVE AFTER SEAT ELEMENT REPLACEMENT. *TT
3483
Service Bulletin/Repair Instructions
POWER WINDOW INOPERATIVE, NOISY OR GLASS DROPS. *TT
4001
Service Bulletin/Repair Instructions
INTERMITTENT UNWANTED DYNAMIC REAR PROPORTIONING (DRP) EVENT. *TT
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.