Vehicle report

2005 BUICK TERRAZA

Service bulletins

488 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIT3532C

Service Bulletin/Repair Instructions

This PI directs technician to training regarding sliding door operation.

PIP5601C

Service Bulletin/Repair Instructions

This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

PIP6057

Service Bulletin/Repair Instructions

This preliminary information discusses a possible moan noise from the rear axle , engineering is reviewing the concern.

PIP5358D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PIT5074P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT5099G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIP5358C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

13-08-116-001I

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

09-00-89-008F

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT3271N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

13-08-116-001H

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5358B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PIT3271M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT3271L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP4723F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

22NA009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

000090002L

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

030091001H

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

010842001N

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

080730035E

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

21NA124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

100089006H

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIP5358A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

16NA338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

020089002T

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

18NA099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

PIP5163E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIP5540G

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5725A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

20NA138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

010601011L

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIT5074N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT3271K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP5628C

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIP5226D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT5099E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5453C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

PIP5628B

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

070849020Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

16NA383

Service Bulletin/Repair Instructions

This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

PIP5725

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

020089002S

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

PIT3099T

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIP4723D

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

050307009I

Service Bulletin/Repair Instructions

This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIP5540F

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

100089009D

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.

010842001M

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080310006G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

PIT3271J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5074M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

100089006G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).

PIP5540E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5601A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

010601011K

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

100089009C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

17NA073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

150844001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

PIT3099S

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIT3099R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

100845001G

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

060847001O

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIT5074L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

080730035D

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PIP5640

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

PIP5226C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIC5260C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

040089053G

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

070849020P

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

100845001F

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".

PIP5540D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5628

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

17NA170

Service Bulletin/Repair Instructions

This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.

010842001L

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

PIP5540B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

060847001N

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIP4925B

Service Bulletin/Repair Instructions

This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.

PIT5353C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIP5601

Service Bulletin/Repair Instructions

This Preliminary information communicates

PIT5099D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5163D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIT5399A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIP5338B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

080730035C

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

030603004W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

060601010D

Service Bulletin/Repair Instructions

This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.

PIP5226B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT3271H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP5540A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

100864002D

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

PIP5540

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

16NA075

Service Bulletin/Repair Instructions

This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds

120089007A

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

010601011J

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

070604019F

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

PIC3100F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PIT5353B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

070849020M

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide

150089004B

Service Bulletin/Repair Instructions

Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

150089005A

Service Bulletin/Repair Instructions

Essential Tools that Include Consumable Parts (U.S. Only)

030603004V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

PIP4723C

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5074K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5389E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIT3099Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

PIP5163C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5588D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

PIT3099P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

00-06-01-012G

Service Bulletin/Repair Instructions

This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.

03-06-03-004U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

15-08-44-001I

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

15-08-73-001A

Service Bulletin/Repair Instructions

This informational bulletin explains how to update the older Onstar module software to new software over GSA.

06-08-47-001M

Service Bulletin/Repair Instructions

This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.

10-00-89-006F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report.

PIT5389C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

07-07-30-010D

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.

PIC4935F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

PIP4723B

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIC3278G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4801H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIC5588C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

02-00-89-002Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

PIP5029H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

PIP5338A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

17-NA-016

Service Bulletin/Repair Instructions

This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.

08-03-10-006F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

03-08-46-004S

Service Bulletin/Repair Instructions

This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

07-08-49-020L

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

08-08-44-015H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIC5492E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

02-00-89-002P

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

05-00-89-055F

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.

PIT3099N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIP5163B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT5389B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

030603004S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

030603004T

Service Bulletin/Repair Instructions

Battery Testing and Warranty Replacement Requirements (North America ONLY)

100844006D

Service Bulletin/Repair Instructions

This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.

05-08-44-024E

Service Bulletin/Repair Instructions

This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .

09-00-89-008C

Service Bulletin/Repair Instructions

This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

09-00-89-016E

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.

08-08-44-015G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

07-08-49-020K

Service Bulletin/Repair Instructions

This informational bulletin explains the programming method quick reference guide for the IPC Odometer.

PIC5491J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

PIP5029G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

PIT5074J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

PI1394A

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.

PIP4786C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

030603004R

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.

000601012F

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.

030604017I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

000601026I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.

00-06-01-026H

Service Bulletin/Repair Instructions

This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.

PIP5094A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.

PIT-5485-B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIT5485B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIC5088F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

PIC-4935-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC-5050-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

PIC4935E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC5050A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

PIT5389A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

PIT5485A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIC-5260-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIC5260A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

00-03-10-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.

16-NA-075

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds

PIC6181

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

08-07-30-026C

Service Bulletin/Repair Instructions

This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

PIP5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

03-06-03-004O

Service Bulletin/Repair Instructions

This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)

PIT5484A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

PIT3046G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an inaccurate fuel gauge. Technician should drive the vehicle to duplicate the concern. The fuel gauge will have a tendency to falsely indicate a lower fuel level than what is actually present. The fuel gauge will take a few minutes to show the correct fuel level. On vehicles equipped with an automatic transmission no buffering takes place when the transmission is in park or neutral. This is a normal characteristic and no repairs are necessary. On vehicles equipped with a manual transmission the fuel gauge is buffered in all gears and neutral. There is a timer which starts to count up when the clutch is depressed. When this timer reaches its calibrated value the buffering stops. This is a normal characteristic and no repairs are necessary.

PIC5953A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

02-08-42-001I

Service Bulletin/Repair Instructions

This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not

11-00-89-005I

Service Bulletin/Repair Instructions

This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)

PIP5226A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

08-08-44-015F

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)

01-08-42-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on exterior lamp condinsation and replacement guidelines

PIT4720D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.

16-NA-025

Service Bulletin/Repair Instructions

This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks

03-08-46-004R

Service Bulletin/Repair Instructions

This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)

06-06-01-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.

PIC6140B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

PIT5353A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT5484

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

PIT5485

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that unable to place calls to OnStar while in ignition ON mode after performing the OnStar Canada upgrade. Engineering is aware of the issue and is working on a solution. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT5486

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT4943D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

06-00-89-031D

Service Bulletin/Repair Instructions

OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

07-08-49-020J

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

15-NA-079

Service Bulletin/Repair Instructions

OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer – or any dealer near you – as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."

PIP5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

PIC3100E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

15-08-44-001F

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

15-08-44-001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

PIC6140A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

01-06-01-011I

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIC5953B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP5338

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

05-03-07-009H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIT5464

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5325

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

15-00-89-005

Service Bulletin/Repair Instructions

This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).

00-06-01-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

09-09-40-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

03-06-03-004N

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).

07-06-04-019E

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

02-00-89-002O

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).

PIC6107

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

15-08-44-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

PIC6101

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.

PIT5384A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

02-07-30-052J

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.

05-06-04-035E

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.

15-08-44-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-44-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

02-08-42-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

PIT5399

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIC4310L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

00-05-22-002O

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with a brake lathe calibration procedure.

15-08-44-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-73-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.

PIT5264C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

05-00-89-055E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.

06-08-47-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.

10-08-45-001E

Service Bulletin/Repair Instructions

This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.

00-03-10-002I

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.

PI1394

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.

PIT3271G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIC3278F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4310K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

03-00-91-001G

Service Bulletin/Repair Instructions

This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

030848006J

Service Bulletin/Repair Instructions

This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.

1008110001C

Service Bulletin/Repair Instructions

This information provides the proper way to install the floor mats .

PIT5074H

Service Bulletin/Repair Instructions

J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.

PIT5353

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIP5029F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

PIT5264B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

11-00-89-005H

Service Bulletin/Repair Instructions

This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.

PIT5099A

Service Bulletin/Repair Instructions

A/C Blows Warm Or Poor Performance.

06-08-43-003E

Service Bulletin/Repair Instructions

This informational bulletin explains how to care for wiper blades.

PIP5232A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

07-08-49-020I

Service Bulletin/Repair Instructions

This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.

PIT5264A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

PIC6036

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.

PIP5232

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

08-08-44-015E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIP5226

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

10-08-110-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to use floor mats.

10-08-44-006C

Service Bulletin/Repair Instructions

This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.

02-00-89-002N

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

10-00-89-006E

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

03-06-03-004M

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

PIT3099M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIC4310J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

00-06-01-012E

Service Bulletin/Repair Instructions

This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.

PIP5163A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

00-00-89-027H

Service Bulletin/Repair Instructions

This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.

02-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

10-00-89-006D

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

Recalls

Service Bulletin/Repair Instructions

Vehicle Recalls

050308002F

Service Bulletin/Repair Instructions

This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.

PI0373B

Service Bulletin/Repair Instructions

This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.

PIC5088E

Service Bulletin/Repair Instructions

This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.

05-00-89-029C

Service Bulletin/Repair Instructions

This preliminary bulletin provides a information to the dealer for the requirements need for equipment.

PIC5588B

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

09-03-10-013B

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.

03-06-03-004L

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

05-06-04-035D

Service Bulletin/Repair Instructions

This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.

01-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.

02-08-42-001G

Service Bulletin/Repair Instructions

This informational bulletin is to assist with the identification of issues that are not considered warrantable.

PIT3099L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PI1217

Service Bulletin/Repair Instructions

This preliminary bulletin provides a way to aid the technician in diagnosing transmission fluid leaking from the trans breather vent.

03-06-03-004K

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not

PIT5264

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

PIT4864F

Service Bulletin/Repair Instructions

Information On Requests To Add OnStar Bluetooth Option.

PIC3011H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

10-08-64-002C

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

08-03-10-006E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.

PIT4943C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

PIC5453A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

99-08-51-007F

Service Bulletin/Repair Instructions

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

04-00-89-053F

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

PIC5953

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP3140F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

08-08-44-029D

Service Bulletin/Repair Instructions

This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.

PI0281D

Service Bulletin/Repair Instructions

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

10-00-89-006C

Service Bulletin/Repair Instructions

This informational bulletin provides directions on submitting different PIRs

08-08-44-015D

Service Bulletin/Repair Instructions

This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.

05-00-89-072C

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.

10-08-110-001A

Service Bulletin/Repair Instructions

This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.

PIP5163

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT3099K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

130089009

Service Bulletin/Repair Instructions

Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules

06-00-89-026L

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.

PIC5904

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

06-06-01-010B

Service Bulletin/Repair Instructions

This informational bulletin provides information on close-coupled converter and engine replacement.

00-03-10-003R

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.

03-06-03-004I

Service Bulletin/Repair Instructions

This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.

10-00-89-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key codes security rules and information on GM key code look up application.

10-00-89-009B

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

05-09-40-002G

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.

07-08-49-020H

Service Bulletin/Repair Instructions

This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.

00-05-22-002N

Service Bulletin/Repair Instructions

This informational bulletin provides information for Disc Brake Warranty Service and Procedures.

02-07-30-052I

Service Bulletin/Repair Instructions

This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.

08-06-01-006D

Service Bulletin/Repair Instructions

This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.

11-00-89-005E

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.

02-08-98-002D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.

09-00-89-008A

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.

07-03-10-015C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.

05-08-48-001C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.

05-03-07-009F

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.

13-00-89-004B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 13-00-89-004A to include updated information.

06-00-89-026K

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.

09-07-30-018D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.

09-00-89-016C

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.

PIT4720C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

03-06-03-004H

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.

13-00-89-005

Service Bulletin/Repair Instructions

This technical bulletin provides Warranty Administration - New Labor Codes information.

13-00-89-004A

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.

99-04-20-002H

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.

13-00-89-004

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 10-00-89-017Z to include updated information.

11-00-89-005D

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.

10-00-89-017Z

Service Bulletin/Repair Instructions

This informational bulletin provides information on fix it right for first time issues.

00-03-10-002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.

PIP3140E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

PIP5094

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

08-08-51-002A

Service Bulletin/Repair Instructions

This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.

03-00-89-013H

Service Bulletin/Repair Instructions

This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)

PIP5064C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that after installing a reman High Value V6 engine it has rough running, idle surge, misfire on one or both banks of the engine concern. Technician may find Diagnostic Trouble Codes P0300, P0011 and / or P0016. Technician will need to check the actual engine oil pressure. If oil pressure is within the specifications above, perform all testing listed in PIP4345A including a visual inspection of the camshaft position actuator filter and repair or replace as necessary. Technician will need to contact General Motors Technical Assistance Center for further assistance if the concern is still present.

PIP-5064-B

Service Bulletin/Repair Instructions

BUICK/CHEVROLET/PONTIAC/SATURN: AFTER INSTALLING REMAN HVV6 ENGINE, WOULD BE CONCERN WITH ROUGH RUNNING OR MISFIRE ON ONE OR BOTH BANKS OF ENGINE OR IDLE SURGING. MODELS 2005-11 LUCERNE, RENDEZVOUS, TERRAZA, IMPALA, MALIBU, MONTE CARLO, UPLANDER, G6, MONTANA SV6, AURA, RELAY, VUE. *PE UPDATED 4/9/13. *PE

11-00-89-005C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm

PIC3718E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

PIT3173C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

10-00-89-017X

Service Bulletin/Repair Instructions

This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.

080846004A

Service Bulletin/Repair Instructions

This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.

000089027G

Service Bulletin/Repair Instructions

This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.

PIC4310H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

06-00-89-026J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

060089026J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

100089010B

Service Bulletin/Repair Instructions

This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.

01-00-89-010J

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.

010089010J

Service Bulletin/Repair Instructions

This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

100089017W

Service Bulletin/Repair Instructions

This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.

PIT4907A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

100864002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

PIC4935D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

PIT3099J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

09-07-30-018C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions

12-00-89-007

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

PI0373A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.

11-00-89-005B

Service Bulletin/Repair Instructions

This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm

10-00-89-017V

Service Bulletin/Repair Instructions

This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.

PIC5588A

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

09-09-40-001A

Service Bulletin/Repair Instructions

GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE

05-09-40-002E

Service Bulletin/Repair Instructions

GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE

PIT 3395

Service Bulletin/Repair Instructions

CHIME SOUND WHEN VEHICLE IS PUT INTO GEAR. *EH UPDATED 8/1/11. *PE

PB-10037A

Service Bulletin/Repair Instructions

GM: ONSTAR IS MAKING INCOMPLETE CALLS WITHOUT THE DRIVER KNOWING. WHEN HAVE A DATA CONNECTION. *RM

3532

Service Bulletin/Repair Instructions

SERVICE VME - POWER SLIDING DOOR ADJUSTMENT PROCEDURE. *TT UPDATED. *KB UPDATED 11/23/09. *PE

PIT-4855

Service Bulletin/Repair Instructions

BUICK/CHEVROLET/PONTIAC/SATURN: POWER SLIDING DOOR DOES NOT POWER OR MANUAL UNLOCK. DIAGNOSTICS MAY REVEAL THAT SLIDING LOCK BUTTON ON INSIDE DOOR PANEL WILL NOT MOVE FROM LOCKED TO UNLOCKED POSITION. *PE

PIT-3046E

Service Bulletin/Repair Instructions

GMC: FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL, CAUSING THE LOW FUEL LIGHT TO ILLUMINATE. *PE

PIC4845

Service Bulletin/Repair Instructions

PART RESTRICTION - POWER SLIDING DOOR ACTUATOR CONTROL MODULE ASSEMBLY. *NJ

PIT-4663

Service Bulletin/Repair Instructions

GMC: POWER SLIDING DOOR ONLY OPENS FROM INSIDE/OUTSIDE DOOR HANDLE(S). NEITHER RIGHT/LEFT SLIDING DOOR WILL NOT OPEN FROM THE OVER HEAD CONSOLE SWITCH, B-PILLAR SWITCH, OR RKE KEY FOB. *PE

080730002

Service Bulletin/Repair Instructions

INFORMATIONAL ON 4T65-E MN7, M15 AND M76 FRONT WHEEL DRIVE AUTOMATIC TRANSMISSION VALVE BODY RECONDITIONING, DTCS P0741, P0742, P0757, P842, HARSH SHIFTS OR SLIPS. *PE

3743

Service Bulletin/Repair Instructions

VARIOUS ABS DTC'S AND INTERMITTENT CONCERNS. *NJ

070523003

Service Bulletin/Repair Instructions

PULSATION/VIBRATION WHEN APPLYING BRAKES (REPAIR ROTOR VARIATION AND INSTALL NEW FRONT BRAKE SHIELDS) *NJ

070849013

Service Bulletin/Repair Instructions

FUEL GAUGE READS EMPTY WHEN FUEL TANK IS FULL, LOW FUEL LIGHT COMES ON WHEN FUEL TANK IS FULL, DTC P0463 STORED (REPLACE FUEL LEVEL SENSOR). *NJ

0508110002

Service Bulletin/Repair Instructions

BROKEN OVERHEAD STORAGE COMPARTMENT LATCH(ES) (REPLACE LATCH(ES). *TT UPDATED 07-23-07. *KB

050854001

Service Bulletin/Repair Instructions

HIGH EFFORT TO SOUND HORN, HORN ONLY SOUNDS WHEN CERTAIN SPOTS ARE PRESSED. *TT

070232003

Service Bulletin/Repair Instructions

POWER STEERING CLUNK, KNOCK NOISE. *KB

050603003

Service Bulletin/Repair Instructions

HEADLIGHTS AND INTERIOR LIGHTS FLICKER. *TT UPDATED. *KB

060604003

Service Bulletin/Repair Instructions

SERVICE ENGINE SOON (SES) LIGHT ILLUMINATED, MULTIPLE POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) P1404 AND/OR P0404. 06-06-04-003 NOT YET RECEIVED. *TT UPDATED 04-27-07. *KB

060601014

Service Bulletin/Repair Instructions

L36, L67, L26, L32, LA1, LX9, MN7, M15. TICKING OR KNOCKING TYPE NOISE COMING FROM THE ENGINE OR TRANSMISSION AREA. *KB

010845005

Service Bulletin/Repair Instructions

HARD START, NO START, STALL, AND/OR FUEL GAUGE INOPERATIVE OR FLUCTUATES. *YH UPDATED *EH

060730023

Service Bulletin/Repair Instructions

4T65E TRANSMISSION 1-2 SHIFT SHUDDER AT LIGHT TO MODERATE ACCELERATION. REPLACE COMPLETE SECOND CLUTCH ASSEMBLY. *KB

060309003

Service Bulletin/Repair Instructions

REVISED BALL JOINT INSPECTION PROCEDURE AND INDEPENDENT REAR SUSPENSION. *KB

050601036

Service Bulletin/Repair Instructions

LX9 INTERMITTENT DTC/MIL P0300 OR ENGINE STUMBLE/HESITATION AT 5400 RPM OR HIGHER PRIOR TO TRANSMISSION UPSHIFT. ORIGINAL NOT YET RECEIVED. *TT

1613174

Service Bulletin/Repair Instructions

A STALL AND/OR NO CRANK, NO START CONDITION AFTER THE WIPERS ARE USED. THE SERVICE ENGINE SOON LIGHT MAY OR MAY NOT BE ILLUMINATED AND THE CUSTOMER MAY REPORT OTHER PROBLEMS WITH THE CRUISE CONTROL SYSTEM. A TECH 2 DIAGNOSTIC PROBE WILL FIND NUMEROUS DTCS WHICH COULD INCLUDE P0608 CRUISE CONTROL, C0460, C0461 STEERING WHEEL SENSOR CODES, AND POSSIBLY A NO COMMUNICATION ISSUE WITH THE PCM. ENGINEERING HAS DETERMINED THE WIPER MOTOR CRANK ARM IS CONTACTING THE UBEC WIRING HARNESS AND CUTTING THE WIRES. *TT

050308013

Service Bulletin/Repair Instructions

REVISED FRONT SUSPENSION FASTENER TIGHTENING SPECIFICATIONS. *TT

050601005A

Service Bulletin/Repair Instructions

WHISTLE TYPE NOISE COMING FROM ENGINE. *TT

050602008

Service Bulletin/Repair Instructions

REVISED RADIATOR REPLACEMENT. *TT

050843006

Service Bulletin/Repair Instructions

REVISED WIPER MOTOR REPLACEMENT PROCEDURE. *TT

050850010

Service Bulletin/Repair Instructions

HARD SPOT OR LUMP FELT IN DRIVER AND/OR PASSENGER SEAT. *TT

050604052

Service Bulletin/Repair Instructions

INFORMATION ON INVERTED KNOCK SENSOR - DIAGNOSTIC TROUBLE CODE P0327 KNOCK SENSOR (KS) CIRCUIT BANK 1 OR DTC P0332 KNOCK SENSOR (KS) CIRCUIT BANK 2. *TT

05548A

Service Bulletin/Repair Instructions

PROGRAM BULLETIN (CUSTOMER SATISFACTION PROGRAM)-ENGINE HARMONIC BALANCER NOT SEATED. *SC

030950001

Service Bulletin/Repair Instructions

CHILD COMFORT CLIP COMES OFF FROM SEAT. *TT

07-08-64-007

Service Bulletin/Repair Instructions

GENERAL POWER SLIDING DOOR DIAGNOSIS/REPAIR PROCEDURES. *KB UPDATED 2/25/08. *NJ UPDATED 7/15/08. *NJ UPDATED 8/14/08. *PE UPDATED 9/23/08. *PE

050864013

Service Bulletin/Repair Instructions

POWER SLIDING DOOR BOUNCES WHEN IT STOPS, DOES NOT ACHIEVE FULL OPEN POSITION, DRIVER INFORMATION CENTER (DIC) MESSAGE DISPLAYED. *TT

050864009

Service Bulletin/Repair Instructions

DOOR GLASS INOPERATIVE. *TT

05539

Service Bulletin/Repair Instructions

PRODUCT EMISSION RECALL TO REPLACE THE POWERTRAIN/ENGINE CONTROL MODULE (PCM/ECM). THE POWERTRAIN/ENGINE CONTROL MODULE (PCM/ECM) MAY HAVE BEEN MANUFACTURED WITH DAMAGED INTERNAL IC CHIPS, WHICH MAY AFFECT THE FUEL PUMP CONTROL AND EGR OUTPUTS OF THE PCM; OR THE FUEL PUMP CONTROL AND VARIABLE NOZZLE TURBO CONTROL (VNTC) OUTPUTS OF THE DIESEL ECM. *TT

030848005A

Service Bulletin/Repair Instructions

COMPASS ZONE ADJUSTMENT AND CALIBRATION PROCEDURE DURING PRE-DELIVERY INSPECTION. VARIOUS MODELS INCLUDING 2002-2004 LIGHT DUTY TRUCKS. *TT UPDATE TO INCLUDE 2005 BUICK ALLURE. *TT

040844023

Service Bulletin/Repair Instructions

VARIOUS RADIO/CD PLAYER CONCERNS. *TT

050137001

Service Bulletin/Repair Instructions

REAR BLOWER MOTOR NOISE. *TT

000940001B

Service Bulletin/Repair Instructions

EXCESSIVE LATERAL MOVEMENT (SIDE TO SIDE) WHEN USING CERTAIN AFTERMARKET CHILD SEATS. THIS CONDITION OCCURS IN VEHICLES EQUIPPED WITH SECOND AND THIRD ROW BUCKET SEATS. INCLUDING THE 1997 - 1999 OPEL SINTRA. *TT

050940001

Service Bulletin/Repair Instructions

AVOIDING 3RD ROW CENTER SEAT BELT RETRACTOR LOCK-UP. *TT

3046A

Service Bulletin/Repair Instructions

FUEL GAUGE FLUCTUATION IN PARK OR NEUTRAL. *TT

3213

Service Bulletin/Repair Instructions

UNABLE TO FLASH PASSENGER PRESENCE SYSTEM DIAGNOSTIC TROUBLE CODES. VARIOUS MODELS INCLUDING 03-05 CHEVROLET FULL SIZE TRUCKS AND UTILITIES, AND GMC FULL SIZE TRUCK. *EH

3259

Service Bulletin/Repair Instructions

HOOD SWITCH DIAGNOSTICS AND OPERATION. THIS ALSO INCLUDES 2005 PONTIAC SV6 AND 2005 SATURN RELAY. *EH

3266

Service Bulletin/Repair Instructions

FRONT DOOR GLASS BINDS. THIS ASLO INCLUDES 2005 PONTIAC SV6 AND 2005 SATURN RELAY MODEL. *EH

3278

Service Bulletin/Repair Instructions

LEFT OR RIGHT POWER SLIDING DOOR INOPERATIVE DIAGNOSTIC TROUBLE CODE B1292. THIS ALSO INCLUDES THE 2005 SATURN RELAY. *EH

3286

Service Bulletin/Repair Instructions

SEATBELT INDICATOR LIGHT IS FLASHING WHILE DRIVING. *EH

3299

Service Bulletin/Repair Instructions

STALL, NO CRANK, NO START AFTER USING THE WIPERS. *TT

3318

Service Bulletin/Repair Instructions

REAR LIFT GATE IS INOPERATIVE. *TT

3323

Service Bulletin/Repair Instructions

NOISE OR CLUNK IN THE REAR SUSPENSION. *TT

3332B

Service Bulletin/Repair Instructions

DIAGNOSTIC TROUBLE CODE P0404 EGR CONCERN. *TT

3337

Service Bulletin/Repair Instructions

UNWANTED HEATED SEAT, AND OR THE REAR DEFROSTER/DEFOGGER SHUT OFF. *SC

3365A

Service Bulletin/Repair Instructions

TICKING OR KNOCKING NOISE CRACKED OR BROKEN FLEXPLATE. VARIOUS MODELS INCLUDING OLDSMOBILE BONNEVILLE 2006. *TT

3377

Service Bulletin/Repair Instructions

CRANK, NO START CONDITION WITH NO SPARK. *TT

3399

Service Bulletin/Repair Instructions

ENGINE CRANKS BUT WILL NOT START. *SC

3448

Service Bulletin/Repair Instructions

INSTRUMENT PANEL CLUSTER INOPERATIVE INTERMITTENTLY WITH POSSIBLE DIAGNOSTIC TROUBLE CODES. *TT

3500

Service Bulletin/Repair Instructions

REPEAT FAILURES OF ALL-WHEEL DRIVE TRANSFER CASE AND/OR TRANSMISSION - UNABLE TO ATTAIN CORRECT TRANSFER CASE SELECTIVE WASHER MEASUREMENT. *TT

3550

Service Bulletin/Repair Instructions

STARTER STAYS ENGAGED AFTER ENGINE STARTS. *AK

3660

Service Bulletin/Repair Instructions

SUPPLEMENT TO SIT-N-LIFT SEAT INSTALLATION INSTRUCTIONS. *TT

3679

Service Bulletin/Repair Instructions

REAR DISC BRAKE DRAG OR CONTINUING TO HOLD. *TT

3688

Service Bulletin/Repair Instructions

REAR MAIN OIL SEAL LEAK. *TT

3705

Service Bulletin/Repair Instructions

VEHICLE PULLS HARD TO THE RIGHT ON SOME CROSSOVER U-VANS WITH CONTINENTAL TIRES. *TT

3763A

Service Bulletin/Repair Instructions

INTERMITTENT NO CRANK, NO START AND/OR DEAD BATTERY. *TT

3764

Service Bulletin/Repair Instructions

DTC B0105 AFTER THE A SDM REPLACEMENT. *KB

3772

Service Bulletin/Repair Instructions

CLUNKING NOISE FROM THE REAR OVER BUMPS. *TT

3798

Service Bulletin/Repair Instructions

VARIOUS POWER SLIDING DOOR ISSUES. *KB

3861

Service Bulletin/Repair Instructions

STIFF REAR SUSPENSION OR SHOCKS CLUNK OVER BUMPS. *TT

4072

Service Bulletin/Repair Instructions

HARD START, NO START, CAUTION LIGHT, CORROSION AT C305. *TT UPDATED 08-15-07. *KB

4157

Service Bulletin/Repair Instructions

ALL WHEEL DRIVE DISABLE LAMP ON. *KB

4184

Service Bulletin/Repair Instructions

HEADLAMPS AND/OR INTERIOR LIGHTS FLICKER INTERMITTENTLY. *KB

4607

Service Bulletin/Repair Instructions

RUNNING OUT OF GAS WHILE PARKED WITH 1/4 TANK OR LESS WHEN DOWNWARD ON INCLINE. *NJ

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2005 Buick Terraza Service Bulletins: 488 bulletins | CarFathom