Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
22-NA-205
This service bulletin provides information on Module Harvesting.
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
3249
HIGH SPEED SHAKE OR VIBRATION. *EH
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIC4696E
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable. E version update is to add administrative details.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIC4696D
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco TheftLock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code. The PI update to version D is to advise the unlock procedure is temporarily unavailable.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIP5601
This Preliminary information communicates
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC4696C
This Preliminary Information communication provides information to the technician on how to unlock radios that are Delco Theft Lock. Technician will use the radio to get the scrambled code. Technician will need to contact the radio unlock center to retrieve the unlock code from the scrambled code.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
17-NA-016
This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5232C
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
16-NA-025
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIT5486
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT4943D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
15-NA-079
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIP5346
This Preliminary Information communication provides information to the technician about cooler line fittings that come with the 4T65E General Motors remanufactured transmission may not be the same as Original equipment manufacturer quick connect verses inverted flare. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC5953B
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5464
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIC6107
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIT5384A
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
05-06-04-035E
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
15-08-44-001
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5029F
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT5264B
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
14299D
Unintended Ignition Key Rotation
PIT5099A
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5232A
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
14299A
Unintended Ignition Key Rotation
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
Recalls
Vehicle Recalls
PIC5588B
Programming And Activation Of Replacement OnStar Modules.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
PIT3099L
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIT5264
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIC3011H
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
PIT4943C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5913
This Preliminary Information communication provides information to the technician about vehicles that have a Supplemental Inflatable Restraint lamp, Service Vehicle Soon lamp on and/or radio locked, possibly after module replacement. Technician will need to check for an incorrect or non-existent VIN number in modules that require them. Technician should ensure that all modules that are replaced are programmed per currently published Service Information. Technician should also check the Sensing and Diagnostic Module part number if it was replaced.
PIT3099K
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
PIT4720C
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
13-00-89-005
This technical bulletin provides Warranty Administration - New Labor Codes information.
99-04-20-002H
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
PIP3140E
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
08-08-51-002A
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
PIC3718E
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
000089027G
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
09-09-40-001A
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
SB-10-08-50-003B
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
050861002
FLOOR PAN CORROSION PERFORATION IN BATTERY COMPARTMENT. *TT UPDATE. *TT UPDATED ON 06/30/2011. *KB
08089-B
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
08-089
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
PIC-4887
GMC: HARSH RIDE OR LINE INSTALLATION CONCERN WITH DELCO SHOCK KIT. CONCERNS WITH CONNECTING THE LINES TO THE SHOCKS AND THE AIR COMPRESSOR. CONCERN OF HARSH RIDE AFTER INSTALLATION. *PE
050861007
CLUNK NOISE FROM FRONT OF VEHICLE WHILE DRIVING OR SHIFTING IN AND OUT OF GEAR. *KB
3951
KNOCKIG NOISES OR EXCESSIVE OIL CONSUMPTION. VEHICLES WITH LD8 OR L37 4.6L V8 ENGINES. *KB
020604024D
SERVICE ENGINE SOON OR CHECK ENGINE SOON MALFUNCTION INDICATOR LAMP BEING ILLUMINATED. *TT 02-06-04-024E NOT YET RECEIVED. *TT
050525010A
TRACTION CONTROL LIGHT ON/TRACTION CONTROL INOPERATIVE, DIAGNOSTIC TROUBLE CODE (DTC) C1295 STORED IN HISTORY (PERFORM DIAGNOSTIC CHECKS). *TS
050854002
HORN(S) INOPERATIVE (INSTALL NEW HORN(S) IN A REARWARD FACING POSITION). *TT
709
DRIVER'S SEAT WILL NOT RETURN TO ITS MEMORY SEAT POSITION WHEN THE RKE FOB IS USED ON AN INTERMITTENT BASIS. GM TECH LINK. *TT
020730039E
FIRM TRANSMISSION SHIFTS, SHUDDER/CHUGGLE, TRANSMISSION WON'T DOWNSHIFT ON DECELERATION, SERVICE ENGINE SOON LIGHT ILLUMINATED, DIAGNOSTIC TROUBLE CODE P0742 SET. *TT UPDATE. *TT
050310004
TIRE PRESSURE MONITORING (TPM) SYSTEM - TIRE MOUNTING AND DISMOUNTING. *TT
020862002A
SERVICE PROCEDURE AVAILABLE FOR REAR FASCIAS THAT MAY BECOME DISTORTED / WARPED WHEN IN HIGH AMBIENT TEMPERATURES. *TT
030847001A
CIGAR LIGHTER AND ACCESSORY POWER OUTLETS TIME OUT 10 MINUTES AFTER IGNITION SHUT-OFF OR OUTLETS REMAIN ON AFTER IGNITION SHUT-OFF. *TT UPDATE. *TT
010846008B
INFORMATION ON UPGRADING FACTORY INSTALLED ONSTAR GENERATION 2.0 EQUIPPED VEHICLES TO GENERATION 2.6. *TT UPDATE. *TT
030844005B
POOR RADIO RECEPTION OR RADIO STATIC/ INCREASED INTERFERENCE WITH REAR WINDOW DEFOGGER ON OR SOME REAR WINDOW DEFOGGER GRIDS MAY BE INOPERATIVE. *TT
000310007F
VEHICLES MAY EXPERIENCE SHAKE / VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *JB UPDATED *EH GM VOICEMAIL MESSAGE. *TT
040604071
INFORMATION ON REPLACEMENT SERVICE ENGINES REQUIRING A PCM (POWERTRAIN CONTROL MODULE) REPROGRAM. *TT
040316001
TIRE PRESSURE SENSOR LEARN-SERVICE TIRE MONITOR MESSAGE BEING DISPLAYED THROUGH THE DIC. *SC
010308004
FIRM/HARSH REAR SEAT RIDE. *YH *AR
040730034
SERVICE ENGINE SOON (SES) LIGHT ON, DIAGNOSTIC TROUBLE CODE (DTC) P0741, TORQUE CONVERTER CLUTCH (TCC) EXCESSIVE SLIP, TRANSAXLE CHUGGLE, SLIP/SURGE. *TT
040605008
AVAILABILITY OF EXHAUST MUFFLER FOR SERVICE. *TT
07012004
REAR SHOCK ABSORBER UPPER RUBBER MOUNT. *SC
040139004
HVAC CONTROL MODULE LENS SCRATCHED. *TT
040604022
POWERTRAIN CONTROL MODULE WILL NOT PROPERLY COMMUNICATE ON BOARD DIAGNOSTIC OXYGEN SENSOR TEST INFORMATION TO NON-TECH2 SERVICE OR TEST EQUIPMENT. *EH
000310007E
SHAKE/VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT UPDATE. *TT
030235002
MINOR SCRATCHES TO WOOD STEERING WHEELS. *TT UPDATE. *TT
040309001
SERVICEABILITY OF REAR SHOCK ABSORBER - UPPER RUBBER MOUNT. *TT
990603009A
FLOOR PAN CORROSION PERFORATION IN BATTERY COMPARTMENT. *TT UPDATE *EH
00062A
ENGINE EXHAUST LEAK NOISE HEARD INSIDE THE VEHICLE. SIT BULLETIN 1412205. *TT
01606
SERVICEABILITY OF THE UPPER MOUNT FOR REAR SHOCK ABSORBERS. *TT
01709
INDENTATION OF REAR FASCIA NEAR URPA SENSOR. SIT BULLETIN 1454741. *TT
01748
ROUGH IDLE WITH NO POWERTRAIN CONTROL MODULE (PCM) DIAGNOSTIC TROUBLE CODE (DTC) AND NO DRIVEABILITY COMPLAINTS. *TT
01771
4.0L L47, 4.6L LD8, L37, LH2 ENGINE COOLANT OR OIL LEAK.*MR
01792
4.0L L47, 4.6L LD8 L37 ENGINE WATER PUMP COVER P/N 12571913- THERMOSTAT LOOSE. ALSO INCLUDING MODEL 2003 CADILLAC ELDORADO. *MR
01907
LOUD POP FROM A-PILLAR AREA WHEN GOING OVER BUMPS. *TT
01915
WINDNOISE WITHIN THE PASSENGER COMPARTMENT AREA FROM BOTH REAR DOORS QUARTER GLASS AREA. *TT
02006
4.6L LD8, L37 ENGINE GUIDELINES FOR ENGINE REPLACEMENT. *MR
02038
DIAGNOSTIC TROUBLE CODE B1000. *MR
02079
UPDATED CRANKSHAFT SENSORS. 4.6L LD8 L37 ENGINE NORTHSTAR. *TT
02103
4T80E MH1 SERVICE ENGINE SOON (SES) LIGHT ON WITH DIAGNOSTIC TROUBLE CODE (DTC) P0741 (TCC STUCK OFF). *TT
02141
REPEAT ANTI-LOCK BRAKE SYSTEM (ABS) LIGHT WITH DIAGNOSTIC TROUBLE CODE (DTC) C1225. VARIOUS MODELS INCLUDING 2005 CADILLAC DEVILLE. *TT
040730003
WHINE/HUM NOISE FROM AUTOMATIC TRANSAXLE BETWEEN 20 MPH - 50 MPH (32 - 80 KM/H) WITH LIGHT THROTTLE APPLICATIONS. *TT
3001
VOLUME IS ONLY CONTROLLED USING STEERING WHEEL CONTROLS. *TT
3013
C1298 IN EBTCM AND UI040 IN POWERTRAIN CONTROL MODULE (PCM), DURING KEY POWER MODE CHANGES. *MJ
3015
MULTIPLE STABILITRAK/PRECISION CONTROL CODES SUCH AS C1282, C1283, C1284, C1285, C1287, AND C1288 EXIST ON DELPHI BOSCH 5.0 OR 5.3 SYSTEMS. *TT
3035
SERVICE ENGINE SOON (SES) LIGHT ON, SES LIGHT ON AND CHUGGLE OR SURGE. DIAGNOSTIC TROUBLE CODE P0741 (TCC STUCK OFF). *TT
3036
NORTHSTAR UPDATED CRANKSHAFT SENSORS. *TT
3124
REPLACEMENT SERVICE ENGINES REQUIRE A PCM REPROGRAM. *TC
030601029
REVISED FRONT ENGINE MOUNT AND REPLACEMENT PROCEDURE. *TT
00914D
4.6L, LD8, L37, 4.0L, L47 ENGINES NORTHSTARS OIL CONSUMPTION. SERVICE VME. *TT
01352
INFORMATION ON UPGRADING FACTORY INSTALLED ONSTAR GENERATION 2.0 EQUIPPED VEHICLES TO GENERATION 2.6. SUPPLEMENT TO 01-08-46-008. *TT
01388
FRONT ENGINE MOUNT REPLACEMENT DUE TO CLUNK NOISE. SERVICE VME. *TT
01393
4.6L ENGINE PACKAGING CONCERN ON CYLINDER HEAD GASKET KITS. *TT
11062003
WHEEL SPEED SENSOR. *EH
030232049
RELEASE OF NEW OUTER TIE ROD ENDS FOR SERVICE. *TT
020601009C
HIGHER THAN EXPECTED OIL CONSUMPTION. *TT
030601027
THIS BULLETIN IS BEING ISSUED TO INFORM DEALERS OF ENHANCEMENTS TO CRANKCASE, OIL DISTRIBUTION PLATE AND OIL PAN SEALING BY USING RTV SEALANT. *TT
091503
CLUNK NOISE BEING EMITTED FROM FRONT ENGINE MOUNT. GM VOICEMAIL LOG. *TT
030601025
ENGINE COLD/KNOCK/TICK NOISE. *TT
030236002
REVISED STEERING WHEEL POSITION SENSOR OR STEERING SHAFT LOWER BEARING REPLACEMENT PROCEDURE AND STEERING WHEEL POSITION SENSOR CENTERING PROCEDURE. *EH
063003
THIS PURPOSE OF THIS VME MESSAGE IS TO CLARIFY INSTALLATION INSTRUCTIONS FOR A BLOWER MOTOR USED ON PREVIOUS BODY STYLE CADILLACS WITH THE NORTHSTAR ENGINE. *TT
030235003
DIAGNOSTIC INFORMATION FOR BRAKE SELF-APPLY. *TT
031203
ENGINE NOISE THAT ENTERS THE VEHICLE THROUGH THE FRONT OF DASH. *TT *JB
010604002A
CHECK ENGINE LIGHT CONCERN OR REPEAT CONCERN OF DIAGNOSTIC TROUBLE CODE P0101 SET. *TT
01478
NORTHSTAR ENGINE CRANK SENSORS. SERVICE VME. *TT
010849013B
INSTRUMENT PANEL (IP) UPPER TRIM PANEL AND DEFROSTER GRILLE LIFTING / LOOSE / WARPING. *TT
020137009
FLUTTER NOISE WITH AIR CONDITIONER ON FULL COLD, MODE AT BI-LEVEL, BLOWER AT MED / HI AND RECIRCULATION ON. *TT
020601009A
HIGHER THAN EXPECTED OIL CONSUMPTION. *TT
010850001C
FRONT / REAR HEATED SEAT INOPERATIVE / COLD. *TT
09182002
POOR GROUNDS AT EITHER END OF THE GROUND STRAP FROM THE FRAME TO THE ALTERNATOR MAY BE THE CAUSE OF NO CRANK AND NO START CONDITIONS AND ARE PROBABLY ACCOMPANIED BY SEVERAL U DIAGNOSTIC TROUBLE CODES. *TT
020866009
CRACKED TAIL LAMP ASSEMBLY DUE TO OVERSLAM OF REAR COMPARTMENT LID. *TT
000310007C
SUBJECT REGARDING SHAKE / VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT
020730031
INFORMATION ON INSPECTING THE JULIAN DATE CODE OF TORQUE CONVERTER CLUTCH PLUSE WIDTH MODULATED VALVE ASSEMBLY. *TT
010232001B
SOME CUSTOMERS MAY COMMENT ON A CLUNK TYPE NOISE COMING FROM THE FRONT OF THE VEHICLE DURING A TURNING MANEUVER. *TT
062402
CUSTOMER COMPLAINTS OF EXCESSIVE TRANSMISSION NOISE IN THE PASSENGER COMPARTMENT THAT COMES FROM THE ENGINE COMPARTMENT. *TT
210602
THE SUBJECT OF THIS MESSAGE IS THE WARPING OF THE REAR BUMPER FASCIA. *TT
00310007B
TECHNICAL INFORMATION REGARDING SHAKE / VIBRATION IN STEERING WHEEL, FLOOR, SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS. *TT
020137005
SUBJECT REGARDING A/C SHUTS OFF FOR 3-5 MINUTES IN HOW WEATHER WITH VEHICLE SPEED AT / ABOVE 113 KM/H (7U0 MPH). *TT
020232001B
SOME OWNERS MAY COMMENT ON A MOAN / SQUAWK NOISE DURING LOW SPEED TURNING MANEUVERS. *TT
020235003
SERVICE INFORMATION REGARDING RUBBING NOISE FROM STEERING COLUMN. *TT
042602
THIS MESSAGES STATES THAT A NEW BULLETIN HAS BEEN RELEASED ON DIAGNOSING STEERING MOAN ON LOW SPEED TURNS. *TT
060402
INFORMATION ON THE EMERGING ISSUE BROADCAST. *TT
020308004
SOME CUSTOMERS MAY COMMENT ON A SQUEAK/SQUAWK NOISE FROM FRONT OF VEHICLE WHEN TRAVELLING OVER ROAD BUMPS/SWELLS. *TT
020604019
SOME OWNERS MAY COMMENT ON AN INTERMITTENT ENGINE IDLE SPEED STABILITY CONCERN, HARD OR NO RESTART CONDITION OR A DECEL ENGINE STALL. *TT
020864009
SOME CUSTOMERS MAY COMMENT THAT THEIR DOOR GLASS IS SCRATCHED. *TT
020604014
SUBJECT REGARDING THE ELIMINATION OF THE SERVICE BAY TEST PROCEDURE. *TT
270202
SUBJECT REGARDING COMPLAINTS OF REAR AIR CONDITIONING SYSTEM STAYING ON AT ALL TIMES. *TT
010730009B
SUBJECT REGARDING NO POWER ON HEAVY ACCELERATION OR 1-2 SHIFT CONCERNS-DELAYS,SLIPS,FLARES, DIAGNOSTIC TROUBLE CODE P0731 AND/OR DIAGNOSTIC TROUBLE CODE P0732 SET. *YD
250102
CONCERNS WITH POWER STEERING MOAN CONDITION AT LOW PARKING LOT MANEUVER SPEEDS AND WHEN MAING RIGHT HAND TURNS. *TT
020232001
CONCERNS WITH MOAN/SQUAWK NOISE DURING LOW SPEED TURNING MANEUVERS. *TT
211201
CONCERNS WITH POWER STEERING MOAN PRIMARILY ON RIGHT HAND TURNS. *TT
171201
SUBJECT CONCERNING INTERMITTENT DIAGNOSTIC TROUBLE CODE P0443, OF RAPID OF PURGE SOLENOID. *TT
131201
SUBJECT REGARDING TIRE VIBRATION AT HIGHWAY SPEEDS ON SMOOTH ROAD SURFACES. *TT
081101
SOME VEHICLES MAY EXHIBIT A DIAGNOSTIC TROUBLE CODE AFTER INSTALLING A REPLACEMENT ABS EBCM. *TT
061101
CONCERNS WITH A POTENTIAL LEAK PATH INTO THE TRUNK AREA. *TT
000849005A
INFORMATION REGARDING INTERMITTENT DIGITAL INSTRUMENT CLUSTER CONCERNS. *YH
010603009
INFORMATION REGARDING SERVICE ELECTRICAL SYSTEM MESSAGE DISPLAYED. *YH
010850001A
SUBJECT REGARDING FRONT/REAR HEATED SEAT BEING INOPERATIVE OR COLD. *YH
101101
INFORMATION ON ANALOG CELL PHONE BOOSTERS TO IMPROVE UV8 CELL PHONE PERFORMANCE. *TT
051001
INFORMATION REGARDING DEFECTIVE HEATED SEAT ELEMENTS IN LIEU OF REPLACING THE ENTIRE SEAT COVER ASSEMBLY. *YH
000310007A
INFORMATION REGARDING SHAKE/VIBRATION IN STEERING WHEEL, FLOOR,SEAT AT HIGHWAY SPEEDS ON SMOOTH ROADS (DIAGNOSE/BALANCE TIRES/WHEELS). *YH
010526002
INFORMATION REGARDING PARKING BRAKE NOT RELEASING AUTOMATICALLY. BRAKE WARNING LAMP ON AFTER SHIFTING FROM PARK. *YH
250901
CONDITIONS ON A P1575 DIAGNOSTIC TROUBLE CODE. *SLC
060901
SOME VEHICLES MAY EXPERIENCE A POWER STEERING SQUAWK NOISE DURING LOW SPEED TURNS, MOST OFTEN WHEN TURNING RIGHT. *SLC
000523001A
INFORMATION REGARDING REAR BRAKE MOAN/HUM NOISE DURING BRAKE APPLY. *YH
01045A
INFORMATION REGARDING ONSTAR GLOBAL POSITIONING SYSTEM (GPS) *JG
010846003
SOME CUSTOMERS MAY COMMENT THAT THE CALLED PARTY HAS DIFFICULTY HEARING THE CALLER WHEN USING THE CELL PHONE IN THE HANDS-FREE MODE. *TT
11601
CAMPAIGN INFORMATION PROCESSING SYSTEM WILL BE SENDING OUT AN ADDITIONAL OWNER NOTIFICATION ON THE FOLLOWING CAMPAIGNS: 00001, 00008, 00022, 00035, AND 00041
010601
SUBJECT REGARDING PCM PROGRAMMING ADAPTER FOR 2000 - 2002 4.6L V8 EQUIPPED CADILLAC VEHICLES. *TT
010235004
VEHICLES BUILT PRIOR TO VIN BREAKPOINT 1U183517 MAY EXHIBIT HIGH EFFORT TO OPERATE STEERING COLUMN SHIFT LEVER OUT OF PARK. *TT
010730005A
SOME OWNERS MAY COMMENT ON NO 4TH GEAR OR IT SLIPPING IN 4TH GEAR. THE
010730009A
SOME VEHICLES WITH HYDRA-MATIC 4T80-E AUTOMATIC TRANSMISSIONS MAY EXHIBIT AN INTERMITTENT NO POWER AND DIAGNOSTIC TROUBLE CODE P0731, INCORRECT 1ST GEAR RATIO AND / OR DIAGNOSTIC TROUBLE CODE P0732, INCORRECT 2ND GEAR RATIO. *TT
030501
CUSTOMER COMMENTS OF STEERING MOAN, GROAN, CLICK OR OTHER NOISE AT SLOW PARKING LOT MANEUVER SPEEDS. STEERING SYSTEM MAKES A MOAN WHEN MAKING A RIGHT HAND TURN IN PASSING ROUGHLY 270 DEGREES OF STEERING WHEEL ROTATION AT UNDER FIVE MILES PER HOUR. *TT
010301
CONCERNS WITH THE POWER STEERING SYSTEMS. *TT
010523004
SOME OWNERS MAY COMMENT ABOUT HOT BRAKE ROUGHNESS THAT IS CHARACTERIZED BY FRONT END SHAKE AND STEERING WHEEL VIBRATION DURING A BRAKE APPLICATION. *TT
010730009
SUBJECT REGARDING INTERMITTENT NO POWER AND DIAGNOSTIC TROUBLE CODE (DTC) P0731, INCORRECT 1ST GEAR RATIO AND / OR DTC P0732, INCORRECT 2ND GEAR RATIO. *TT
010850001B
CUSTOMERS MAY COMPLAIN THAT THE FRONT/REAR SEAT ASSEMBLY HEAT FUNCTION IS NOT OPERATING PROPERLY. *SLC
130201
INFORMATION REGARDING 4T80E AUTOMATIC TRANSMISSION (WHINE NOISE). *JB
010730005
SOME ONWERS MAY COMMENT ON NO 4TH GEAR OR SLIPPING IN 4TH GEAR. *TT
000848002A
SUBJECT PERTAINING TO WHISTLE NOISE FROM UPPER WINDSHIELD / WINDSHIELD UPPER CORNER REVEAL MOLDING AREA. *JB
010101
GM POWERTRAIN IS INVESTIGATING A WHINING NOISE IN THE 4T80E TRANSMISSION DUE TO SPALLING / PITTING ON THE DRIVE AND / OR DRIVEN SPROCKET THRUST BEARINGS. *TT
010844001
INFORMATION REGARDING NAVIGATION SYSTEM LOSES ROAD NAMES IN DETAILED MAP TURN-BY-TURN MAP AND VOICE GUIDANCE. *JB
010850001
INFORMATION ON FRONT / REAR HEATED SEAT INOPERATIVE / COLD. *JB
000139001A
SOME CUSTOMERS MAY COMMENT THAT ONE OR MORE OF THE INSTRUMENT PANEL AIR OUTLET VENT SHUT-OFF DOORS MAY CLOSE WHEN THE BLOWER FAN IS ON HIGH. *TT
201000
SUBJECT REGARDING THE CELL PHONE INTEGRATION OPTION, ALSO KNOWN AS RPO-UV8. *TT
000848002
SUBJECT PERTAINING TO A WHISTLE TYPE WIND NOISE FROM UPPER WINDSHIELD REVEAL MOLDING AREA ON VEHICLES BUILT PRIOR TO VIN YU312523. *TT
000849005
SUBJECT REGARDING INTERMITTENT DIGITAL INSTRUMENT CLUSTER CONCERNS (SOP THROUGH VIN BREAKPOINT YU229401). *TT
000854002
A CONDITION MAY EXIST WHERE THE HORN CONTINUOUSLY ACTIVATES WHEN COLD / HORN BECOMES INOPERATIVE ON VEHICLES BUILT PRIOR TO CERTAIN VIN BREAKPOINTS. *TT
99079A
CERTAIN VEHICLES NOT EQUIPPED WITH THE MEMORY / PERSONALIATION CONVENIENCE PACKAGE MAY EXHIBIT A CONDITION IN WHICH THE BATTERY RUNS DOWN WITHIN ONE DAY. *TT
99141
GENERAL MOTORS HAS DECIDED THAT CERTAIN VEHICLES HAVE CLIMATE CONTROL / DISPLAY MODULES THAT FAIL BECAUSE A PART WAT INSTALLED INCORRECTLY. *TT
99079
SOME VEHICLES NOT EQUIPPED WITH THE MEMORY / PERSONALIZATION CONVENIENCE PACKAGE (RPO WA7) MAY EXHIBIT A CONDITION IN WHICH THE BATTERY RUNS DOWN WITHIN ONE DAY. *TT
99084
GENERAL MOTORS HAS DECIDED THAT CERTAIN VEHCILES HAVE CLIMATE CONTROL / DISPLAY MOUDLES THAT ARE INOPERATIVE. *TT
181199
ADDITIONAL INFORMATION FOR THE STOP DELIVERY OF CERTAIN VEHICLES. *TT
00112A
POPPING NOISE IN THE FOOTWELL AREA. *TT
3357
UNWANTED ALARM ACTIVATION, TRUNK KEY CYLINDER HARD TO OPEN, TRUNK AJAR LAMP ON, FUEL GAUGE INOPERATIVE, RKE INOPERATIVE, INTERIOR LAMPS INOPERATIVE AND/OR NO COMMUNICATION WITH THE REAR INTEGRATION MODULE (RIM). *TT
3409
SERVICE VME - FLOOR PAN CORROSION IN THE BATTERY COMPARTMENT. *TT
3554
THE DRIVER SEAT INTERMITTENTLY DOES NOT RETURN TO ITS MEMORY POSITION. *TT
3937
INSTRUMENT CLUSTER INTERMITTENTLY INOPERATIVE AT START UP. *TT
4001
INTERMITTENT UNWANTED DYNAMIC REAR PROPORTIONING (DRP) EVENT. *TT
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.