PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
23-NA-224
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
18-NA-263
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
This Preliminary information communicates
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
04-06-04-051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
040604051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
030603004S
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
030603004T
Battery Testing and Warranty Replacement Requirements (North America ONLY)
040089015N
This warranty administration bulletin provide policy information on required operating procedures.
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA338
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine, transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
07-00-89-037J
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
08-08-44-029G
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
01-00-89-010L
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
01-03-10-003L
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
10-00-89-005F
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
16-NA-055
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
06-08-50-009I
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
05-08-51-001H
This informational bulletin provides information on removing paint stains on the under side of protective shipping film
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
15-NA-079
OnStar Voice Fallback Number Update
15-NA-069
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
00-03-10-006L
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
15-08-44-001F
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
10-00-89-005E
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
02-07-30-029Y
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
01-06-01-011I
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
08-08-44-029F
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI0799A
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
15-NA-030
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.
06-00-89-031C
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
15-06-03-001A
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PIC6106B
This Preliminary Information communication provides information to the technician about vehicles that may have the radio display that will go blank and come back on after a few seconds then display may show the splash screen or come back on to the last screen that was displayed. Technician should USB update the radio using Tis2Web and follow up with a Service Programming System program.
08-08-44-029E
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
05-03-07-009H
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
PIT5468
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
PIT5464
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5465
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
15-00-89-005
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
10-08-110-001D
This informational bulletin provides information on the proper use of GM floor mats.
00-06-01-026G
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
09-09-40-001C
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
09-00-89-002L
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
99-01-39-004G
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
03-06-03-003E
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
03-07-29-004J
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
03-00-89-006L
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
01-08-51-003E
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
05-06-04-022M
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
06-00-89-029K
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
PIC5491G
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT5442
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
03-06-03-004N
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
07-06-04-019E
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
02-00-89-002O
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).
99-00-89-019M
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
15-08-44-001C
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
09-00-89-002K
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
05-06-04-035E
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-00-89-004A
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
00-06-01-026F
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
15-08-44-001A
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PI0091B
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
02-08-42-001H
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
15-00-89-004
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5282
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
12-07-30-001E
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
13-08-116-001B
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
00-05-22-002O
This informational bulletin provides technicians with a brake lathe calibration procedure.
PIT5236C
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
PI1440
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.
04-00-89-015J
This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.
09-00-89-016D
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
12-06-01-008B
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
15-00-90-001
This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter.
02-07-30-029X
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
15-08-44-001
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-00-89-003
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).
05-06-04-060A
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
08-03-10-004B
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.
05-00-89-055E
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
15-08-42-001
This informational bulletin communicates GM's position on exterior lighting components ?tinted or smoked? by an outside vendor.
05-03-10-020F
This informational bulletin communicates GM's position on use of nitrogen gas in tires.
PI1404
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement.
05-08-51-001G
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.
01-00-89-010K
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).
10-08-45-001E
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
00-03-10-002I
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
03-06-03-003D
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
11-00-89-004A
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PI0360E
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application.
03-00-91-001G
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
15-06-03-001
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PI1385
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always be re-learned when accessory wheels are installed on the vehicle.
030729004I
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
PI0655A
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
030848006J
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
This information provides the proper way to install the floor mats .
100089005D
This warranty informational bulletin advised the technician that when performing a wiring repair, more information is required.
PIT5074H
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
PIT5236B
OnStar Module Does Not Support All B101D Symptom Codes.
990420002I
Information on Driveline Clunk Noise
PIT5099A
A/C Blows Warm Or Poor Performance.
PIT5264B
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
PIT5353
XM Audio Traffic And Travel Link Availability And Operation.
14-00-89-003A
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time
06-08-43-003E
This informational bulletin explains how to care for wiper blades.
PIP5232A
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
04-00-89-015H
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
PI1098A
This preliminary bulletin provides a procedure on how to cold crank test a battery in a vehicle.
PIC6036
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
04-06-04-047M
This informational bulletin states that it no longer valid and refers to a new bulletin.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
This informational bulletin provides information on how to use floor mats.
05-06-04-022K
This informational bulletin provides information on top tier fuels and what brands are available.
10-08-44-006C
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.
07-00-89-036G
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
02-00-89-002N
This informational bulletin provides additional information to the technicians and how to submit a field product report.
10-00-89-006E
This information bulletin provides the dealers on how to submit a product information report.
03-06-03-004M
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
09-00-89-002J
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
PI1296
This preliminary bulletin provides additional diagnoses for engine misfires, popping noise after cylinder head or fuel rail repair.
00-03-10-006K
This informational bulletin provides the technician with information on tire radial force variations and how to use it.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1290
This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose mirrior and/or bracket fell off.
PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
99-01-39-004F
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5759A
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
12-03-10-001B
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
02-00-89-002M
This informational bulletin provides additional information to the technicians and how to submit a field product report.
10-00-89-006D
This information bulletin provides the dealers on how to submit a product information report.
10-08-46-001B
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
PIP4902H
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
14-00-89-003
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.
Recalls
Vehicle Recalls
PI1266
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.
PI0373B
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
PIC5088E
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
05-00-89-029C
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
12-00-89-002B
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
03-00-89-006K
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
PIP4653E
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
02-07-30-029W
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
12-07-30-001D
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
03-06-03-004L
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
00-03-10-006J
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
03-03-10-007I
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
13-00-89-004I
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
06-00-89-029J
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
PI1235
This preliminary bulletin provides information to the technician, to check for loose grounds and the correct labor op to use
PI1233
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
02-07-30-029V
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
130089004I
Car and Truck Fix it Right the First Time Issues
PIC5687D
Checking Smartphone Bluetooth Software Update Status
09-00-89-002I
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
01-08-42-001J
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
13-00-89-004H
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
1406130001
High Voltage Safety ? High Voltage Disabling
03-06-03-004K
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
13-00-89-004G
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIC5687C
Checking Smartphone Bluetooth Software Update Status
PIC5959A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIT5264
Canadian Customers Unable To Place Calls In The United States
12-07-30-001C
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
09-03-10-016B
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
10-08-64-002C
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
12-03-10-001A
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
12-03-10-002A
This informational bulletin provides the technician the proper way to install and torque the wheel.
05-03-10-020E
This informational bulletin explains the use of Nitrogen in GM tires.
08-03-10-006E
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
13-00-89-004F
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
02-08-98-002E
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
05-08-48-001D
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
99-01-39-004E
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
130089004F
Car and Truck Fix it Right the First Time Issues
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5959
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
11-00-89-002B
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
01-07-30-042H
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
08-08-44-029D
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
04-00-89-015G
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
14-00-89-001
This warranty administration bulletin provides information on Premium care maintenance eligibility for vehicle services and maintenance in the U.S. and Canada.
04-00-89-015F
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
07-00-89-037G
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to its customers.
140089001
Cadillac Premium Care Maintenance Eligibility for United States and Canadian Vehicles
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
This informational bulletin provides directions on submitting different PIRs
13-00-89-004E
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
PI0754A
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason.
05-00-89-072C
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
PI0592C
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491).
13-00-89-004D
This informational bulletin provides an update for 13-00-89-004C to include updated information.
00-06-01-026E
This informational Bulletin provides a revision for 00-06-01-026D to add the 2014 model year.
PI0018B
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance.
04-06-04-047L
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
PI1098
This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.
09-06-04-015B
This informational bulletin provides a revision for 09-06-04-015A to add the 2012-2014 model years.
10-08-110-001A
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
130089004D
Car and Truck Fix it Right the First Time Issues
PIC5932
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5491D
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIC5492B
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5236
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
130089004C
Car and Truck Fix it Right the First Time Issues
130089010
PAC Courtesy Transportation Assistance Program
990940005G
Seat Belt Extender Availability
03-06-03-004I
This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.
02-07-30-029U
This informational bulletin provides information for the PQC assembly replacement process.
PI1018
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
10-00-89-010C
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
This informational bulletin provides information on key code security and information on GM key code look up applications.
130089008
GM Wiring Repair Strategy Information
130090001
Information for Engine Oils Used in 2014 Model Year Vehicles
04-00-89-015E
This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S. version of Bulletin 12-00-89-003.
03-00-89-006J
This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.
05-09-40-002G
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
12-02-32-002A
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
00-05-22-002N
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
PI0011C
This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update Warranty Information.
13-00-89-006
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year.
PI0574A
This preliminary informational bulletin provides a revision for PI0574A to include the 2013-2014 model year vehicles, update the covered models and the Recommendation/Instructions section.
08-06-01-006D
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
02-08-98-002D
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
11-00-90-001B
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
09-00-89-008A
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
PI0592B
This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.
07-03-10-015C
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.
05-03-07-009F
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.
13-00-89-004B
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
06-00-89-026K
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.
10-00-89-016A
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the Labor Operation graphic.
09-03-16-002B
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.
09-07-30-018D
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.
10-00-89-005C
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
11-00-89-007C
This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation List.
07-00-89-037F
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
03-08-48-006I
This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.
03-06-03-004H
This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.
090730018D
Change in Automatic Transmission Add Condition Documentation and Claim Submission
130089004B
Car and Truck Fix it Right the First Time Issues
PIT5214
GM TAC Support of Vehicle Vibration Complaints.
13-00-89-005
This technical bulletin provides Warranty Administration - New Labor Codes information.
13-00-89-004A
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.
03-06-03-003C
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
99-04-20-002H
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
13-00-89-004
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
PI0572B
This preliminary information bulletin is for information on COAX Repair Kit Availability. Revised from PI0572A
130089003
Vehicle Software Enhancements
130089004
Car and Truck Fix it Right the First Time Issues
130089004A
Car and Truck Fix it Right the First Time Issues
11-00-89-005D
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
09-00-89-002H
This informational bulletin provides information for dealers to properly maintain vehicle in inventory.
06-00-89-029I
This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats carpet, vinyl.
13-08-116-001A
This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected tampering.
09-06-04-026G
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
10-00-89-017Z
This informational bulletin provides information on fix it right for first time issues.
00-03-10-002G
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
1308116001A
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
PI0412B
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
00-03-10-006I
This informational bulletin provides information on tire radial force variation.
02-07-30-029T
This informational bulletin provides information on the replacement process for the product quality center.
12-07-30-001B
This informational bulletin provides information for service agents not required to contact product quality center for CNG, LPG or gasoline engine, transmission and/or transfer case.
13-08-116-001
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices causing multiple issues.
09-06-04-026F
This informational bulletin provides information on suspected tampering on vehicles modifications for identifying non GM ECM calibrations.
03-00-89-013H
This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)
11-00-90-001A
This informational bulletin provides information on the proper oils to use on GM vehicles including information regarding the differences of the Dexos oils.
11-00-89-005C
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIT3173C
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
10-00-89-017X
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
PI0774B
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation settings for concernc regarding noice drop outs during calls and muffled sound.
08-08-44-015C
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
00-00-89-027G
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
000089027G
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4801E
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIT4733J
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
120310002
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
PIC5687B
This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.
060089026J
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
100089010B
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
120089002A
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
01-00-89-010J
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
010089010J
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
10-00-89-017W
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
100089017W
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
030846004M
This informational bulletin provides information on part restriction and ordering process information for onstar vehicle communication interface modules.
PIT4907A
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
10-08-64-002B
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
100864002B
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
PIC4935D
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIT3099J
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
09-06-04-026E
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2 or GDS 2
09-07-30-018C
This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions
12-00-89-007
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
PI0373A
This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.
PIT3237F
This Preliminary Information communication provides information to the technician about the percentage of Ultraviolet protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
PIC5759
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
11-00-89-005B
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
07-00-89-037E
This warranty administrational bulletin provides information on courtesy transportation and roadside assistance programs offered through GM.
10-00-89-017V
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
090730018C
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.