PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIC6086J
This PI communicates a procedure to clean oil leaking from the rain sensor.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
PIP4964F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
13-02-32-001H
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP6027
This Preliminary information communicates that due to parts shortages we are resticting part number 19435910.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT6261
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC6086H
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
24-NA-147
This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
18-NA-115
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update
PIP5913A
This Preliminary information communicates additional diagnostics to help isolate source of complaint.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
21-NA-147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminatedâ.
PIC6123G
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
23-NA-162
This service bulletin advises the tech of updated Diagnostic procedures in Service Information (SI) to avoid misdiagnosis when addressing a customer concern of Service Rear Axle Message displayed on the Driver information Center (DIC).
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17-NA-040
This service bulletin provides a procedure to correct a condition of Brake Squeal or Squeak Noise Intermittently on Initial Brake Applies.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
PIP4964E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
17-NA-281
This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIP5913
This Preliminary information communicates additional diagnostics to help isolate source of complaint.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
19-NA-256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PIT5698C
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
18-NA-358
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC6435B
This Preliminary information communicates that U1523 may set after right headlamp replacement due to a part issue. Engineering is looking into the concern.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
04-06-04-051F
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
18NA067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
070316004D
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
000090002L
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
18NA358
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
17NA040
This service bulletin provides a procedure to correct a condition of Brake Squeal or Squeak Noise Intermittently on Initial Brake Applies.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIC6424A
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module. The newer hardware is not compatible with whatis currently loaded into the SPS programming system. Engineering is working on a new software set to address the concern.
19NA256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698B
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
21NA152
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.
21NA147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
070089037Q
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIC6435A
This Preliminary information communicates that U1523 may set after right headlamp replacement due to a part issue. Engineering is looking into the concern.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
21NA108
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil.
PIP5257E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PI0653A
Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center A Service Agent (Dealer) during vehicle service may need to replace an engine turbocharger (TC). Any turbocharger that is returned to the Warranty Parts Center (WPC) will be inspected by engineering for root cause failure. The Warranty Part Center (WPC) has received turbochargers returned by Service Agents that have been disassembled, damaged during removal from the engine, electrical harnesses or connectors that have been cut or removed from the turbocharger and/or improperly packaged turbochargers resulting in shipping damage.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
070089036J
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
PIC6435
This Preliminary information communicates that U1523 may set after right headlamp replacement due to a part issue. Engineering is looking into the concern.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
010601011L
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PIC6086G
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
090604026S
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
18NA115
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
16NA205
This Technical bulletin provides a procedure to correct a customer concern of Blu-Ray Movies Do Not Start After Play Icon Selected on Menu.
PIP5180C
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIC6376D
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent. The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698A
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
20NA026
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP5095G
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5528F
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
PIC6376C
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent. The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
PIP5528E
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately following HFV6 re-manufactured engines replacement.
120232002B
This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
070604025M
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
20NA098
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIC6376B
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent. The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP5257D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
20NA029
This technical bulletin provides a Service Procedure to correct a Condition of Ticking, Tap or Rattle Noise from Engine.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIC6123F
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
PI0592F
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA321
This technical bulletin provides a procedure to replace the catalytic converters due to cracks that may cause a noise or exhaust smell within the cabin.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP4670H
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIP5528D
This Preliminary information communicates the repair recommendations for misfire in HFV6 re-manufactured engines.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PI0592E
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
090604026R
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIC6123E
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
130089008B
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
19NA182
This technical bulletin provides repair information to correct a customer concern of "Steering Assist Is Reduced" Message and One of The Following DTCs Are Set: C056D, U0415.
PIC6086F
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIC6123D
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
PIT5698
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIC5779K
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
19NA081
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5257C
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIC6137F
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 1 - 2.5 hours depending on model year. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 1 - 2.5 hours depending on model year. If the fob is located, the timer will reset an additional 1 - 2.5 hours depending on model year.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5528C
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIP4964D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIC5756B
This Preliminary Information communication provides information to the technician about vehicles that intermittently the Outside Air Temperature displays dashes instead of a numeric value. This is normal operation of the CUE system, whenever the battery is disconnected and reconnected for service repairs.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
PIC5815D
This Preliminary Information communication provides information to the technician about vehicles that may have sit lower at being parked for several days. It is important to note that, under normal conditions, it is typical and acceptable for the air suspension system to drop slightly over time. Dealers can remind customers that cycling the ignition or starting the vehicle will bring the trim height back to normal levels.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5331H
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIC6360
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
PIC6123C
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
PIC6063C
This Preliminary Information communication provides information to the technician about vehicles that may have the park assist warning that goes off without an object near the vehicle. Engineering is aware of this concern and is working on a software change for this issue.
PIC6013E
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. If needed, also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
PIC6042B
This Preliminary Information communication provides information to the technician about vehicles that if replacement of either shift paddle is necessary, the steering wheel does not need to be replaced nor does it need to be removed to replace either shift paddle.
PIP5528B
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
030729004L
This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.
PIP4670F
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5319F
This Preliminary Information communication provides information to the technician that some vehicles may have a rattle coming from the turbo on a cold start. If the technician has verified the rattle noise when cold is from the turbocharger, and the noise is unforced, there is a revised part available for this concern.
PIP5331G
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
110849001Z
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5528A
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured engines.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT4945H
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010310003R
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
120601003C
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying RTV Sealant.
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
110849001Y
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
PIC5494J
This Preliminary Information communication provides information to the technician when the customer comments that their digital vehicle speed display is showing a different speed than the analog vehicle speed display. There may be up to 2 miles per hour difference between the digital and analog vehicle speed displays. This is a normal condition due to the calculation tolerances being different for the two driver viewing angles for the analog speedometer; it may also appear to increase the difference between both displays. No part replacement is required as this is a normal operating characteristic of the vehicle. For CTS vehicles built between April and June of 2011 or the 2013 ATS, SRX, XTS built before August 29 2012 may have a 3 mile per hour or more variation. The technician is to replace the instrument panel cluster for this concern.
PIT5444D
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17NA066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
000310003X
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIC5822F
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIE0480A
This engineering information PI is requesting information for pictures to be taken of cracked converter pipes.
PIP5191C
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIC6086E
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIP5601
This Preliminary information communicates
PIT4945G
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5597
This Preliminary information communicates to the technician where to find the engine identification tag and what information on that tag to use during programming of someengine control modules.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIC6137E
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 1 - 2.5 hours depending on model year. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 1 - 2.5 hours depending on model year. If the fob is located, the timer will reset an additional 1 - 2.5 hours depending on model year.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIC5779J
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIP3423P
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP5095F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5257B
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5569
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
PIC5692D
This Preliminary Information communication provides information to the technician about vehicles that have a brake pedal may not raise or seem stuck down after a normal braking event. Technician will need to replace the brake pedal arm.
18NA141
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
18NA125
This informational bulletin provides information for engine oil life monitor operation calculation.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
18NA104
This informational bulletin provides information on Hoot, Whine, Buzz, Hiss Noise Coming from Vehicle After Engine is Shut Off and that its a normal condition and no parts should be replaced.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
110849001W
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
010310003Q
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
110089002C
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIC5822E
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
PIP5095E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIC4921E
This Preliminary Information communication provides information to the technician on a proper paint code for some hard to find color options.
PIP5331F
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
18NA045
This technical bulletin provides a procedure to install a pigtail harness to correct the rear tail lights from flashing fast when hot.
PIP5180B
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIP4670E
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
PIC5891E
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
PIC6137D
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 1 - 2.5 hours depending on model year. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 1 - 2.5 hours depending on model year. If the fob is located, the timer will reset an additional 1 - 2.5 hours depending on model year.
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5331E
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100864002D
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
16NA061
This technical bulletin provides a procedure on how to correct tire pressure messages and dashes.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
16NA075
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
130232001E
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
PIP4959G
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
17NA386
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
PI1149A
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
17NA375
This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or pixelated
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
17NA297
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt
PIE0408A
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Rear Shock Absorber Leak and/or Noise.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5815C
This Preliminary Information communication provides information to the technician about vehicles that may have sit lower at being parked for several days. It is important to note that, under normal conditions, it is typical and acceptable for the air suspension system to drop slightly over time. Dealers can remind customers that cycling the ignition or starting the vehicle will bring the trim height back to normal levels.
PIC6042A
This Preliminary Information communication provides information to the technician about vehicles that if replacement of either shift paddle is necessary, the steering wheel does not need to be replaced nor does it need to be removed to replace either shift paddle.
PIC5650C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
17NA172
This informational bulletin provides Specialized Diagnostic Information/procedures for Rear Suspension sag or sitting low.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIC5822D
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
17-NA-172
Rear Suspension Sagging or Sitting Low, Vehicle Not Level After Sitting Overnight Vehicles in new car inventory may be observed or some customers may comment that the rear of the vehicle is riding/sitting low, vehicle sagging, vehicle not level, suspension bottomed out, etc. Review probable causes below.
17-NA-321
Exhaust Smell and/or Leak with Possible Malfunction Indicator Lamp Illuminated Condition Some customers may comment on an exhaust smell and/or leak with possible malfunction indicator lamp illuminated. During diagnosis, a technician may find DTC P0430 and/or P0420. Cause This may be due to a crack around the catalytic mounting flange. Correction Replace converter assembly with new service part.
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
17NA281
This informational bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope
PIT5441C
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, U0268, and/or U0269 stored in the active safety module. Technician should inspect his Multiple Diagnostic Interface cable for damage. Technician should use the Multiple Diagnostic Interface on a like vehicle with object detection bus or theEL-47955-1 MDI 1, MDI 2 Self-Test Loopback Adapter,if there are no issues found finish with diagnosing the customer’s concern, if concern is present in the like vehicle replace the Multiple Diagnostic Interface cable.
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
000601012H
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PIP4959F
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIT5301B
This Preliminary Information communication advises the technician that Diagnostic Trouble Code B127E in the Human Machine Interface with Regular Production Option Code U42 or UWG will be current when playing a DVD or Blu-Ray on the Integrated Center Stack display. When the disc is ejected the Diagnostic Trouble Code will be history. If the Diagnostic Trouble Code B127E remains current after ejecting the disc follow Service Information diagnostic procedure instructions for B127E with Regular Production Option Code U42 or UWG.
03-08-46-004Q
This informational bulletin communicates part restriction and ordering process information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only).
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC6055C
This Preliminary Information communication provides information to the technician about vehicles that may have a radio screen appears bubbled or is delaminating. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
11-08-49-001V
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
PIT5444C
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
16-NA-169
This technical bulletin provides a procedure to remove the trunk applique wire harness and body harness connectors to correct a customer concern of unwanted trunk opening, unable to open trunk, back up camera and/or license plate lamps inoperative caused by to corrosion of the applique wiring harness connector X411, as a result of water intrusion.
04-00-89-015L
This informational bulletin provides warranty policy information on required operating procedures.
10-00-89-005F
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
PIP5507B
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC5779H
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIC6086D
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIC5611E
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5507A
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PI1234C
This preliminary information bulletin provides a procedure on a brief rattle or tick when revving the engine when the vehicle is in P (Park) or N (Neutral). The same rattle or tick can sometimes be heard at the beginning or end of a vehicle acceleration while in D (Drive).
PIP5507
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5216F
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIP5191B
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-125
This technical bulletin provides information for re-torqueing both (RH and LH) rear shock absorber bolts to eliminate a clunk noise from the rear suspension while driving over bumps.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
PI1234B
This preliminary information bulletin provides a procedure on a brief rattle or tick when revving the engine when the vehicle is in P (Park) or N (Neutral). The same rattle or tick can sometimes be heard at the beginning or end of a vehicle acceleration while in D (Drive).
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
16-NA-355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
03-06-03-004U
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
17-NA-084
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
PIP5419B
This Preliminary Information communication provides information to the technician about vehicles that have noise from the exhaust. Technician may find the left hand catalytic converter pipe cracking near cylinder head mounting flange weld. Technician will need to replace the catalytic converter with latest part number from General Motors Service Parts Operations. General Motors is working on a solution for this concern.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
PI1285A
This preliminary informational bulletin provides information on Rear Shock Absorber Warranty Concerns and Diagnostic Tips.
10-00-89-006F
This informational bulletin provides information for dealers how to submit a product information report.
12-09-41-002D
This informational bulletin explains not to put anything metal or conductive on the passenger seat or it may set the reminder chime off.
PIC6013D
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. If needed, also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
PIC6137C
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 1 - 2.5 hours depending on model year. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 1 - 2.5 hours depending on model year. If the fob is located, the timer will reset an additional 1 - 2.5 hours depending on model year.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5095D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
17-NA-047
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5959C
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
16-NA-348
This technical bulletin provides a procedure to install dust deflectors when replacing wheel bearings on vehicles no matter what the concern is of the vehicle.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
02-00-89-002Q
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
PIP5331D
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 model year.
01-03-10-003O
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
07-06-04-025L
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
15-00-90-002A
This informational bulletin provides information on Installing the Correct Replacement Spin-On Oil Filter When Servicing.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP4902J
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIC6086C
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
PIP5319E
This Preliminary Information communication provides information to the technician that some vehicles may have a rattle coming from the turbo on a cold start. If the technician has verified the rattle noise when cold is from the turbocharger, and the noise is unforced, there is a revised part available for this concern.
PIC6123B
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver's information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit's internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
PIP5180A
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
11-08-49-001U
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
99-00-89-019O
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIC4541F
This Preliminary Information communication provides information to the technician with a diagnostic tip for the OnStar back-up battery failure. Technician may find Diagnostic Trouble Code B1446 or B1447 and the OnStar LED is red. Technician should never disconnect the main vehicle battery or remove the OnStar fuse with the ignition key in any position other than off.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIC6137B
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 2.5 hours. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 2.5 hours. If the fob is located, the timer will reset an additional 2.5 hours.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
99-00-89-019N
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
01-03-10-003N
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
02-00-89-002P
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
GCUS-9-3216
16087 Special Coverage. On some vehicles, the hazard flashers may turn on after the vehicle is shut down and/or they may turn on while driving. If the hazard flashers turn on after the vehicle is shut down and left unattended for a long period of time, the battery may die. This anomaly occurs due to a software issue within the switch. Dealers are to replace the hazard switch with a newly designed switch. The repairs will be made at no charge to the customer.
PIC6123A
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range.
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
11-08-49-001T
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
04-06-04-051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
040604051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIC6054D
This Preliminary Information communication advises the technician not to replace any parts and to contact General Motors Technical Assistance Center to report the concern and obtain a case number. Customer's display is slow to turn on when starting the vehicle if the doors were not locked.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
15NA044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
16NA355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
PIP5419A
This Preliminary Information communication provides information to the technician about vehicles that have noise from the exhaust and / or exhaust odor within the vehicle. Technician may find the left hand catalytic converter pipe cracking near cylinder head mounting flange weld. Technician will need to replace the catalytic converter with latest part number from General Motors Service Parts Operations. General Motors is working on a solution for this concern.
PIC5891D
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
PIC6055B
This Preliminary Information communication provides information to the technician about vehicle that may have a radio screen appears bubbled or is delaminating. Dealer can replace model years 2013 and 2015. If working on a 2016 model year vehicle dealer will need to contact General Motors Technical Assistance Center for further assistance. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
030603004S
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
030603004T
Battery Testing and Warranty Replacement Requirements (North America ONLY)
040089015N
This warranty administration bulletin provide policy information on required operating procedures.
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
120137001B
This informational bulletin provides information to dealership personnel on a new refrigerant (R-1234yf) for A/C service.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
07-00-89-037J
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
08-08-44-029G
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
PIC6086B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO RESOLVE THE ISSUE OF AN OILY SUBSTANCE THAT MAY BE FOUND ON THE INSIDE WINDSHIELD SURFACE, AND APPEARS TO BE LEAKING FROM THE REAR VIEW MIRROR AREA. TECHNICIAN WILL REMOVE THE MOISTURE SENSOR AND CLEAN THE GLASS AND MOUNTING BRACKET WITH ALCOHOL WIPE. IF THE GEL SEPARATES FROM THE SENSOR THE SENSOR WILL NEED TO BE REPLACED.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
08-08-44-015G
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIC6104B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE THE LOWER CENTER SECTION OF THE DISPLAY WILL NOT WORK WHEN PRESSED. TECHNICIAN WILL NEED TO REPLACE THE INTEGRATED CENTER STACK FOR THIS CONCERN.
01-00-89-010L
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PI0653D
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
PIP5319D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A RATTLE COMING FROM THE TURBO ON A COLD START. IF THE TECHNICIAN HAS VERIFIED THE RATTLE NOISE WHEN COLD IS FROM THE TURBOCHARGER, AND THE NOISE IS UNFORCED, THERE IS A REVISED PART AVAILABLE FOR THIS CONCERN.
07-08-49-020K
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC6193B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT THE RADIO WILL NOT SAVE XM FAVORITES. TECHNICIAN WILL NEED TO REPLACE THE RADIO TO ADDRESS THE CONCERN.
01-03-10-003L
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIC6073C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
PIP5029G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
PIP5419
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE NOISE FROM THE EXHAUST. TECHNICIAN MAY FIND THE LEFT HAND CATALYTIC CONVERTER PIPE CRACKING NEAR CYLINDER HEAD MOUNTING FLANGE WELD. TECHNICIAN WILL NEED TO REPLACE THE CATALYTIC CONVERTER WITH LATEST PART NUMBER FROM GENERAL MOTORS SERVICE PARTS OPERATIONS. GENERAL MOTORS IS WORKING ON A SOLUTION FOR THIS CONCERN.
16NA241
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
PIC5494G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WHEN THE CUSTOMER COMMENTS THAT THEIR DIGITAL VEHICLE SPEED DISPLAY IS SHOWING A DIFFERENT SPEED THAN THE ANALOG VEHICLE SPEED DISPLAY. THERE MAY BE UP TO 2 MILES PER HOUR DIFFERENCE BETWEEN THE DIGITAL AND ANALOG VEHICLE SPEED DISPLAYS. THIS IS A NORMAL CONDITION DUE TO THE CALCULATION TOLERANCES BEING DIFFERENT FOR THE TWO DRIVER VIEWING ANGLES FOR THE ANALOG SPEEDOMETER; IT MAY ALSO APPEAR TO INCREASE THE DIFFERENCE BETWEEN BOTH DISPLAYS. NO PART REPLACEMENT IS REQUIRED AS THIS IS A NORMAL OPERATING CHARACTERISTIC OF THE VEHICLE. FOR CTS VEHICLES BUILT BETWEEN APRIL AND JUNE OF 2011 OR THE 2013 ATS, SRX, XTS BUILT BEFORE AUGUST 29 2012 MAY HAVE A 3 MILES PER HOUR OR MORE VARIATION. THE TECHNICIAN IS TO REPLACE THE INSTRUMENT PANEL CLUSTER FOR THIS CONCERN.
140089004B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IGNITION KEY, FOB, KEY TAGS AND KEY RINGS CONFIGURATION FOR VARIOUS VEHICLES AND APPLYING A QR CODE STICKER OR BARCODE STICKER TO THE FOB.
16NA249
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
PIC6198A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON STEPS TO PERFORM TO DETERMINE IF THE CUSTOMER'S BATTERY DRAIN CONCERN IS BEING CAUSED BY A KNOWN CONCERN WITH BLUETOOTH CALL TRANSFER OPERATION WHEN EXITING THE VEHICLE. IF THE CONCERN IS DUPLICATED AT THE DEALER WITH THE ONSTAR LED IS STILL GREEN AFTER THE VEHICLE IS TURNED OFF AND THE BLUETOOTH CALL WAS DISCONNECTED. DEALER SHOULD ADVISES THAT ENGINEERING IS AWARE OF THE CONCERN AND IS CURRENTLY INVESTIGATING THE ISSUE.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
PIC6210
THIS PRELIMINARY INFORMATION COMMUNICATES THE PROCEDURE TO THE TECHNICIAN HOW TO REGAIN BLU-RAY/CD/DVD PLAYER FUNCTION ON ALL NEW GENERATION INFOTAINMENT SYSTEMS WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG BLU-RAY PLAYERS. IF THIS CONCERN IS ENCOUNTERED, CYCLE THE CD PLAYER/MEDIA DISC PLAYER FUSE AND RE-EVALUATE THE CONCERN.
07-03-10-008E
THIS INFORMATIONAL PROVIDES INFORMATION ON SLIGHT OR MILD TIRE FEATHERING AND RECOMMENDED PRACTICES.
PIC5428G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE THE ANTILOCK BRAKING SYSTEM, SERVICE TRACTION CONTROL SYSTEM, AND/OR SERVICE STABILITRAK LIGHTS ARE ON. THE ELECTRONIC BRAKE CONTROL MODULE MAY HAVE ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES C0035-C0050 WITH SPECIFICALLY SYMPTOM 18, 5A, OR 0F. TECHNICIAN WILL GAIN ACCESS TO THE CORRECT WHEEL BEAR PER THE DIAGNOSTIC TROUBLE CODE THAT IS SET. IF DEBRIS IS FOUND ON THE MAGNETIC ENCODER RING IT WILL NEEDED TO BE CLEANED.
11-08-49-001R
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
PI1294B
THIS PRELIMINARY INFORMATION BULLETIN PROVIDES A PROCEDURE TO CHECK THE GROUND CONNECTION AND REPROGRAM THE POWER STEERING CONTROL MODULE IF A CUSTOMER COMMENTS ON A INTERMITTENT SERVICE POWER STEERING MESSAGE IS DISPLAYED.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
09-06-04-026M
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PIC-5779-G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. IT IS RECOMMENDED THAT A NON-ALKALINE SOLUTION BE USED FOR PREPARATION & WASHING OF THE BRIGHT ALUMINUM MOLDINGS.
99-08-51-007G
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
PIC-6095-A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH A DIAGNOSTIC AID FOR IDENTIFYING INFOTAINMENT COMPONENTS ON THE VEHICLES TO ENSURE THAT THE CORRECT COMPONENT IS ORDERED OR REPLACED AND THE CORRECT LABOR CODE IS USED FOR WARRANTY SUBMISSION.
PI0592D
This informational bulletin provides information on service programming system (SPS) errors.
PIT-5301-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT DIAGNOSTIC TROUBLE CODE B127E IN THE HUMAN MACHINE INTERFACE WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG WILL BE CURRENT WHEN PLAYING A DVD OR BLU-RAY ON THE INTEGRATED CENTER STACK DISPLAY. WHEN THE DISC IS EJECTED THE DIAGNOSTIC TROUBLE CODE WILL BE HISTORY. IF THE DIAGNOSTIC TROUBLE CODE B127E REMAINS CURRENT AFTER EJECTING THE DISC FOLLOW SERVICE INFORMATION DIAGNOSTIC PROCEDURE INSTRUCTIONS FOR B127E WITH REGULAR PRODUCTION OPTION CODE U42 OR UWG.
12-08-132-001D
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.
16-NA-115
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio inoperative with no communication and DTC U0184, no XM on start-up when manually tuned and/or using voice recognition, no radio wake-up, rear view camera and OnStar hands-free calling issues, favorite stations stored twice and/or disappear caused by to the current software calibration within the radio.
PIP-3140-G
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT A NOISE OR A VIBRATION IN THE VEHICLE THAT SEEMS TO BE ABNORMAL MAY NOT HAVE BEEN THERE WHEN THE VEHICLE WAS PURCHASED. TECHNICIAN SHOULD LOOK FOR NON - GENERAL MOTORS AFTERMARKET ACCESSORIES INSTALLED ON THE VEHICLE THAT CAN CAUSE THESE ISSUES.
11-08-49-001Q
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE IDENTIFICATION OF VEHICLES THAT ARE SHIPPED WITH THE TRANSPORT MODE ON AND HOW TO TURN IT OFF.
PIC-5822-B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF MILDEW ODOR OR WATER ON FRONT FLOOR ON EITHER SIDE OF THE VEHICLE. TECHNICIAN WILL GAIN ACCESS TO THE FRONT WHEELHOUSE OF THE AFFECTED SIDE. THE FRONT WHEEL HOUSE FLANGE MAY HAVE A VOID IN THE SEALER CAUSING WATER TO LEAK THROUGH AND ACCUMULATE ON THE FLOOR OR WET CARPET WILL BE FOUND. A THUMB GRADE SEALER WILL NEED TO BE PLACED IN THE VOID TO PREVENT THE WATER LEAK INTO THE CABIN.
PIC-6086-A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS TO RESOLVE THE ISSUE OF AN OILY SUBSTANCE THAT MAY BE FOUND ON THE INSIDE WINDSHIELD SURFACE, AND APPEARS TO BE LEAKING FROM THE REAR VIEW MIRROR AREA. TECHNICIAN WILL REMOVE THE MOISTURE SENSOR AND CLEAN THE GLASS AND MOUNTING BRACKET WITH ALCOHOL WIPE. IF THE GEL SEPARATES FROM THE SENSOR THE SENSOR WILL NEED TO BE REPLACED.
SB-02-07-30-029Z
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
SB-16NA-131
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIP5189B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.
PIT-5401-F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE. NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN.
PIT5401F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE. NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN.
PIC-6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6198
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
PIC6193A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS. THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.
PIP5168E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
SB-16-NA-115
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE RADIO TO CORRECT A CUSTOMER CONCERN OF RADIO INOPERATIVE WITH NO COMMUNICATION AND DTC U0184, NO XM ON START-UP WHEN MANUALLY TUNED AND/OR USING VOICE RECOGNITION, NO RADIO WAKE-UP, REAR VIEW CAMERA AND ONSTAR HANDS-FREE CALLING ISSUES, FAVORITE STATIONS STORED TWICE AND/OR DISAPPEAR DUE TO THE CURRENT SOFTWARE CALIBRATION WITHIN THE RADIO.
SB-16-NA-116
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE RADIO TO CORRECT A CUSTOMER CONCERN THAT THE HD SWITCHING TOGGLE SETTING DOES NOT FUNCTION AND VOLUME DIFFERENCES BETWEEN ANALOG AND DIGITAL HD SWITCHING DUE TO THE CURRENT SOFTWARE CALIBRATION WITHIN THE RADIO.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
SB-10-08-46-001C
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-6195
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN REPAIR INFORMATION PER MODEL YEAR AND OPTION CONTENT TO HELP DIAGNOSE THE SERVICE DRIVER ASSIST MESSAGE ON THE DRIVERS INFORMATION CENTER.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC6195
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN REPAIR INFORMATION PER MODEL YEAR AND OPTION CONTENT TO HELP DIAGNOSE THE SERVICE DRIVER ASSIST MESSAGE ON THE DRIVERS INFORMATION CENTER.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIP-5331-C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR A POSSIBLE RATTLE, TICK, OR KNOCK TYPE NOISE COMING FROM THE ENGINE.
PIP5331C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR A POSSIBLE RATTLE, TICK, OR KNOCK TYPE NOISE COMING FROM THE ENGINE.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
SB-16-NA-119
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
PIC-6054-C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO REPLACE ANY PARTS AND TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. VEHICLE'S RADIO DISPLAY MAY BE SLOW TO TURN ON WHEN STARTING THE VEHICLE IF THE DOORS WERE NOT LOCKED.
PIC6054C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO REPLACE ANY PARTS AND TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. VEHICLE'S RADIO DISPLAY MAY BE SLOW TO TURN ON WHEN STARTING THE VEHICLE IF THE DOORS WERE NOT LOCKED.
PIC6193
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO MAKE ANY REPAIRS OR REPLACE ANY PARTS. THE TECHNICIAN IS TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER TO REVIEW A CONCERN WHEN THE VEHICLE'S RADIO IS UNABLE TO SAVE A XM PRESET AFTER SAVING PRESETS.
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-16-NA-117
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
PI-0281-E
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC-6187-A
THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.
PIC6187A
THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
SB-16-NA-109
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.
PIP5331B
This Preliminary Information communication provides information to the technician that some vehicles may have rattle, tick, or knock type noise. If there are any drivability concerns they should be addressed prior to the following diagnostic progression. Technician will take a sound file or video with sound of the noise prior to dis-assembly. Technician may find this noise hard to isolate to one area in the engine. There are four different steps to take to diagnosis the concern. Technician will perform injector diagnosis to ensure there are no leaking injectors causing a noise due to excessive fuel in any one cylinder. Replace any out of specification injectors the reevaluate for the noise. Technician will remove the intake manifold and visually inspect for excessive carbon on the intake valve stems and top of the valve causing noise. If carbon is present then follow the latest version of PIP5029 to clean the valves or replace heads as needed. Technician will remove the cam cover of the affected bank (both if needed) to inspect for soft or spongy stationary hydraulic lash adjusters. Push down on the rocker end at the stationary hydraulic lash adjusters to test for soft or spongy. If soft or spongy stationary hydraulic lash adjusters are found, carefully remove the affected head and inspect the oil passage below the head gasket for debris. If debris is found, inspect the camshaft caps for wear or discoloration due to lack of oil. During inspection if wear or discoloration is found then replace the cylinder head assembly with camshafts. If there is no wear or discoloration, clean the oil passages and replace the head gasket. Technician will use chassis ears or a stethoscope; listen to the right and left side of the engine. Once the noise is isolated or if unable to isolate, remove the piston and rod assemblies from the affected bank(s) to inspect for either; a loose rod bushing in the rod, or a loose wrist pin in the bushing. If this is found, replacing the piston an
PIT5236G
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIT5344E
This Preliminary Information communication advises the technician how to diagnose vehicles with the CD player inoperative. If this concern is encountered, cycle the CD player fuse and re-evaluate the concern. If the concern is no longer present, replace the CD player. When the CD player is still found to be inoperative after cycling the fuse follow Service Information diagnostics.
00-03-10-002J
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.
PI0572C
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar®), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.
PI0360F
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications
PIC6187
This Preliminary Information communication advises the technician that some vehicles intermittently the favorites saved from a USB drive or SD card are grayed out and not selectable. Please communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIT5268A
This Preliminary Information communication advises the technician that some vehicles may have a radio display that is covered when the radio station favorites list is maximized. This is a normal operating characteristic and no repair attempt should be made. The hidden screen functions will operate again after the user minimizes the favorites list by dragging it to the bottom of the display.
08-00-89-014B
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics
07-00-89-037I
This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs
16-NA-075
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds
15-06-03-002B
This informational bulletin provides information on Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
PIC6181
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
11-08-49-001P
This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing
16-NA-069
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
03-00-89-006M
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores
03-06-03-004O
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)
06-00-89-029M
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
09-00-89-002M
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
04-00-89-015K
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.
16-NA-061
This informational bulletin provides information on how to trace and complete a wire to wire repair on vehicle that have the concern of Service Tire Monitor System, Tire Pressures Display Dashes, RKE Short Range, No Fob Detected Message
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
PIC5953A
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
16-NA-055
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
PIC6170
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS NEED TO DIAGNOSE AND REPAIR VEHICLE THAT MAY HAVE A CONCERN WITH NAVIGATION ICON NOT SHOWING THE CORRECT LOCATION THEN JUMPING TO THE CORRECT LOCATION. THE POSITION INDICATOR MAY SHOW THE VEHICLE TURNING IN THE OPPOSITE DIRECTION OR MAY SHOW THE VEHICLE TRAVELING OFF THE ROAD. TECHNICIAN WILL INSPECT THE HUMAN MACHINE INTERFACE MOUNTING. FOLLOW SERVICE INFORMATION FOR THE CORRECT ORIENTATION OF THE HUMAN MACHINE INTERFACE.
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
04-06-01-029H
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)
12-09-41-002C
This informational bulletin provides information on Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On or Set DTC B101D When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
08-08-44-015F
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)
16-NA-037
This technical bulletin provides a procedure to reprogram the active safety control module for vehicles with the condition of collision/detection system inoperative
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
PIT4720D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
02-08-98-002F
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange
16-NA-031
This technical bulletin provides a procedure on how to remove door trim panles and replace chime speaker pigtail connectors for vehicles with the condition of intermittent loss of chime from speaker
PIP5264
This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires.
PIP5319C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A RATTLE COMING FROM THE TURBO ON A COLD START. IF THE TECHNICIAN HAS VERIFIED THE RATTLE NOISE WHEN COLD IS FROM THE TURBOCHARGER, AND THE NOISE IS UNFORCED, THERE IS A REVISED PART AVAILABLE FOR THIS CONCERN.
16-NA-025
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
06-08-50-009I
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PI1234A
This preliminary informational bulletin provides information on a turbocharger wastegate brief rattle or tick when revving engine in park or neutral being a normal characteristic and should not have any parts replaced
PIT5401E
Radio Inoperative with No Communication and DTC U0184
PIP5257
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
13-02-32-001D
This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.
16-NA-011
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends
PIC6013C
A customer may comment they receive an "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the DIC when attempting to activate the cruise. Other possible messages may include, Park Assist Symbols Unavailable, Lane Departure Warning Unavailable and Rear Auto Braking Unavailable. If normal diagnostics lead to a concern that can be duplicated and there are no DTCs present, the concern is most commonly caused by one of the following issues. Perform the yaw rate sensor learn procedure (Multi Axis Sensor), clear any DTCs that may have set during programming, and let vehicle go to sleep before evaluating the concern.
06-06-01-010C
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
PIC6013A
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. Also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
05-08-51-001H
This informational bulletin provides information on removing paint stains on the under side of protective shipping film
PIT5332B
HD Radio Turns On Unwanted When Using Radio Station Voice Command.
130232001D
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
16NA011
Infotainment System Will Not Return to Media After Bluetooth Call Ends
PIP5257A
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIC6162
This Preliminary Information communication provides information to the technician about customers may inquire about a section in their owner's manual that addresses the use of high temperature brake fluid that should be used in their car during track use. Racing brake fluid has dry boiling points that are well above the specs of standard DOT 3 (401°) or DOT 4 (446°) brake fluid.
PIT5344D
CD Player Inoperative.
PIT5353A
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5483
This Preliminary Information communication provides information to the technician about the compass on the radio display always shows North. Technician should update the radio with the latest calibrations.
PIC5494F
This Preliminary Information communication provides information to the technician when the customer comments that their digital vehicle speed display is showing a different speed than the analog vehicle speed display. There may be up to 2 miles per hour difference between the digital and analog vehicle speed displays. This is a normal condition due to the calculation tolerances being different for the two driver viewing angles for the analog speedometer; it may also appear to increase the difference between both displays. No part replacement is required as this is a normal operating characteristic of the vehicle. For CTS vehicles built between April and June of 2011 or the 2013 ATS, SRX, XTS built before August 29 2012 may have a 3 miles per hour or more variation. The technician is to replace the instrument panel cluster for this concern.
PIP5319A
This Preliminary Information communication provides information to the technician about vehicles that have a rattle from the turbocharger when cold. The technician will need to verify the noise is coming from the turbocharger before going forward. Technician will need to replace the turbocharger with the updated part number if verified the rattle noise when cold is from the turbocharger.
PIT4943D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC6104A
This Preliminary Information communication provides information to the technician about vehicles that have the lower center section of the display will not work when pressed. Technician will need to replace the Integrated Center Stack for this concern.
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
OnStar Voice Fallback Number Update
PI1187C
Information on Inside Rear View Mirror and Camera Loose Some customers may comment that the inside rear view mirror or front camera is loose or that the mirror/camera mounting bracket is loose or has fallen off. If a vehicle is encountered with the above condition, do not attempt to reinstall the bracket onto the windshield. The above listed vehicles have a revised bracket design that is not serviceable. It is necessary to replace the windshield glass assembly. The bracket comes installed on the new glass assembly. Refer to Windshield Replacement in SI.
PIP5216D
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
15-NA-069
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
00-03-10-006L
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
PIT5214B
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIC3100E
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5756A
This Preliminary Information communication provides information to the technician about vehicles that intermittently the Outside Air Temperature displays dashes instead of a numeric value. This is normal operation of the CUE system, whenever the battery is disconnected and reconnected for service repairs.
PIP5216C
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
15-08-44-001F
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PI1187B
This preliminary informational bulletin provides windshield replacement information to correct a customer concern that the inside rear view mirror is loose or that the mirror mounting bracket is loose or has fallen off.
15-06-03-002A
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
15404
15404 - CUSTOMER SATISFACTION PROGRAM. CERTAIN VEHICLES MAY HAVE A CONDITION THAT IF INVOLVED IN A NON-DEPLOYMENT CRASH MAY NOT AUTOMATICALLY ACTIVATE ANY POST-CRASH ACTIONS, INCLUDING AN AUTOMATIC CRASH RESPONSE (ACR) CALL FROM ONSTAR, DOOR UNLOCK, INTERIOR LAMP ILLUMINATION, HAZARD LAMP ACTIVATION, HVAC BLOWER SHUTDOWN, AND FUEL PUMP SHUTDOWN. A NON-DEPLOYMENT CRASH EVENT IS NOT SEVERE ENOUGH TO DEPLOY THE SEAT BELT PRETENSIONERS OR AIRBAGS. ALL POST-CRASH ACTIONS INCLUDING AN ONSTAR ACR CALL WILL FUNCTION AS DESIGNED FOR ANY CRASH WITH A SEAT BELT PRETENSIONER OR AIRBAG DEPLOYMENT. THE ONSTAR BUTTONS CAN BE PRESSED TO REQUEST HELP, IF NEEDED. DEALERS ARE TO REPROGRAM THE SDM, OR IN SOME INSTANCES, REPLACE THE SDM.
15-NA-060
This informational bulletin provides technicians with diagnostic information for when they may find DTC P175F active in the Transmission Control Module (TCM).
10-00-89-005E
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
PI1126G
This preliminary informational bulletin provides repair information to correct customer concerns about blank screen after startup and reverse, rear view camera message on, touch screen inoperable, Bluetooth and navigation concerns.
PIP5090H
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician may find that the right front axle shaft is not fully seated into the transfer case. Technician will need to inspect the splines on the half shaft for damage. If damage is found replace the half shaft and install a new retaining ring with part number 90223082. When the half shaft does not have damage to the splines technician should replace the retaining ring with part number 90223082. Technician will also need to remove all grease from the transfer case intermediate drive shaft internal splines and axle shaft splines. Apply General Motors grease on intermediate drive shaft splines 0.5 grams in two 120 degree quadrants each, 180 degree apart. Ensure the other two adjacent quadrants have splines free of grease. Apply grease within 15 millimeter of leading spline edge and do not apply in the retaining ring groove.
PIC6137A
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 2.5 hours. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 2.5 hours. If the fob is located, the timer will reset an additional 2.5 hours.
PIP5216B
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
02-07-30-029Y
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
15-NA-044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
PIC6034A
This Preliminary Information communication provides information to the technician about vehicles that when shutting the vehicle off when the radio is turned off prior, the radio will turn back on in the muted condition on the next key cycle. No action should be taken at this time as this is considered a normal operating characteristic.
01-06-01-011I
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
08-08-44-029F
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI0799A
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
PIP3423M
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP4919E
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIC5953B
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIC6063B
This Preliminary Information communication provides information to the technician about vehicles that may have the park assist warning that goes off without an object near the vehicle. Engineering has reviewed the concern and it has been determined that this is a normal operating characteristic.
15-NA-030
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
06-00-89-031C
This informational bulletin provides information to dealership personnel on proper engine and automatic transmission/transaxle identification.
15-06-03-001A
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PIC6137
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 2.5 hours. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 2.5 hours. If the fob is located, the timer will reset an additional 2.5 hours.
PIP5095C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
08-08-44-029E
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PIP5331
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles with a rattle, tick, or knock type noise. Technician will use chassis ears to listen to the right and left side of the engine and isolate which bank the noise is from. Technician should now remove the piston and rod assemblies from the affected bank to inspect for a loose rod bushing in the rod, or a loose wrist pin in the bushing. There should be no metal through the oil and a piston and rod assembly will repair this noise. If technician finds metal refer to the latest version of PIP5216. If no wrist pins or bushings are found loose and all other diagnostics for this type of noise has been exhausted then engine replacement may be necessary.
05-03-07-009H
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
PI0653C
This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged, disassembled or improperly packaged turbochargers returned to Warranty Part Center.
PIC6013B
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. Also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
PIP3423L
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIP5191A
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIT5468
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
PIC6054B
This Preliminary Information communication advises the technician not to replace any parts and to contact General Motors Technical Assistance Center to report the concern and obtain a case number. Customer's display is slow to turn on when starting the vehicle if the doors were not locked.
PIC6085A
This Preliminary Information communication provides information to the technician about vehicles that are unable to access XM Weather. If the system responds by highlighting the XM Weather Icon but it does not enter the application technician should replace the Human Machine Interface module for this concern.
PIT5464
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT5465
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIC6123
This Preliminary Information communication provides information to the technician for the adaptive cruise control or lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
PIT5320
Navigation Voice Prompts Choppy Distorted or Garbled.
15-00-89-005
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
PIC6073B
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIC5692C
This Preliminary Information communication provides information to the technician about vehicles that have a brake pedal may not raise or seem stuck down after a normal braking event. Technician will need to replace the brake pedal arm.
PIE0339B
This engineering information bulletin announces the end of need for information from the field regarding poor A/C performance.
10-08-110-001D
This informational bulletin provides information on the proper use of GM floor mats.
00-06-01-026G
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
07-00-89-037H
This warranty administration bulletin provides policy information on courtesy transportation and roadside assistance programs.
09-09-40-001C
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PI1487A
This preliminary informational bulletin provides diagnostic and repair information to correct a customer concern of IPC gauges sweep, loss of power steering assist, intermittent no crank, reduced engine power and multiple U-codes.
PIT5236F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
PIC 5692
GENERAL MOTORS: BRAKE PEDAL DOES NOT RAISE AFTER APPLY BRAKES REMAIN APPLIED OR BRAKE LIGHTS ON UNWANTED. THE CONDITION MAY OCCUR IN HIGH TEMPERATURE AND HUMIDITY CONDITIONS AND MAY NOT BE REPEATABLE. *JS UPDATED 08/28/2012 *JS UPDATED 10/15/14. *PE UPDATED 2/12/16. *PE
09-00-89-002L
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
PIC5932A
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIE0287C
This engineering information bulletin is requesting information from dealers on a customer concern of engine no crank/no start due to discharged battery.
PIT5236E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
99-01-39-004G
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
03-06-03-003E
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
03-07-29-004J
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
PIT5443
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
03-00-89-006L
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
PIC6108A
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
01-08-51-003E
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
05-06-04-022M
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
06-00-89-029K
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
PIC5491G
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIT5442
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
PI1503
This preliminary informational bulletin provides repair information to correct a customer concern of Low Tire Pressure indicator illuminated and/or slow loss of tire pressure.
03-06-03-004N
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
PI0917F
This preliminary informational bulletin provides repair information to correct a customer concern of intermittent brake squeal or squeak noise on initial brake application.
PIE0329A
This engineering information bulletin is requesting information from dealers on a customer concern of brake lights stay illuminated without brake pedal being pressed.
07-06-04-019E
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
15-06-03-002
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
02-00-89-002O
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).
PIC6107
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
PIC6108
This Preliminary Information communication provides information to the technician to download the USB software from TIS2WEB using the vehicle identification number every time a programming event of the human machine interface module is needed. Damage could be caused to the module if USB programmed with the incorrect software.
PIT5214A
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIT5344C
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
99-00-89-019M
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
PIC6073A
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIC6075A
This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
PIC6104
This Preliminary Information communication provides information to the technician about vehicles that have the lower center section of the display will not work when pressed. Technician will need to replace the Integrated Center Stack for this concern.
15-08-44-001C
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIT5344B
This Preliminary Information communication provides information to the technician about vehicles with a CD player is inoperative. Technician should cycle power to the CD play and retest. If the CD player starts working advise the customer that we apologize for this inconvenience and that General Motors is working on a permanent solution for this concern. If the CD player is still inoperative technician will need to test the power and ground circuits. If no concern with power, ground, or connections, replace the Disc Player.
PIT5411C
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP5216A
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIT5384A
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
PIT5236D
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
09-00-89-002K
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
05-06-04-035E
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-00-89-004A
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
00-06-01-026F
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
03-08-46-004P
This informational bulletin communicates part restriction and ordering process information for OnStar®Vehicle Communication Interface Modules (VCIM) (GMNA Only).
PIC5804A
This Preliminary Information communication advises the technician of steps to take if Pandora is inoperative or experiencing intermittent operation. 1. Verify Pandora is installed on the device. 2. Make sure the device is Bluetooth connected and paired to Cadillac CUE. 3. Make sure stations have been created in Pandora on the device. 4. Launch Pandora by selecting the Pandora Icon on the Integrated Center Stack and allow a few moments for the App to start on the device. 5. Make sure the Bluetooth volume on the device is turned up or on. Pandora volume is controlled by the device since it is a Bluetooth application. 6. Pandora is controlled by the devices connection and data signal. If the device has a poor data signal Pandora may not play. 7. If Pandora is successfully working, the device should display "Accessory". 8. Apple devices must be connected via USB to the vehicle to launch Pandora. Customers can use the "Bluetooth" input under the media selection to stream audio but will not have full control of the device using the radio. 9. Some Android phones require a setting in Pandora to allow Pandora to access automotive audio. Launch Pandora on the phone, in Pandora select settings in the upper right hand corner of the screen, select "advanced" and make sure "Bluetooth for Automotive" is checked and enabled. 10. If all of the above tips have been verified, and the message "No Internet Connection" is displayed on the Integrated Center Stack screen, CUE is not picking up the devices internet connection. Ensure that the device has adequate battery life and a good data signal. Check to see if Pandora can be heard through the device itself. If Pandora is playing through the handset device, try repairing the device and/or switching to a different audio screen and coming back to Pandora. 11. If Pandora is installed on a phone and a media device is also connected, such as an IPod that is hardwired to the vehicle, there may be confusion.
15-08-44-001A
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIP4959E
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIP5209C
This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
PIT5076E
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIC6095
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC4921D
This Preliminary Information communication provides information to the technician on a proper paint code for the following special addition vehicles. 2003 Mary Kay Cadillac models - use paint code WA-160E - Mary Kay Pink Pearl 2004 - 2007 Mary Kay Cadillac models - use paint code WA-983L - Mary Kay Pink Pearl III 2004 Neiman Marcus Cadillac XLR - use paint code WA-111B - Majestic Amethyst Metallic 2008 - 2015 Mary Kay Cadillac models - use paint code WA-590Q - Mary Kay Pink Pearl V 2011 Neiman Marcus Chevrolet Camaro convertible - For the exterior body color, use paint code WA-724S - Mystic Bronze Tri-coat. For the ghost stripes on the hood and deck lid, use paint code WA700T 2013 Hot Wheels Chevrolet Camaro - For the exterior body color, use paint code WA-720S - Kinetic Blue. For the red stripe on the wheels and the front bumper, use paint code WA-799U - Performance Red. 2015 Green Flash Camaro models - use paint code WA-136X - Unripened Green
PIC5494E
This Preliminary Information communication provides information to the technician when the customer comments that their digital vehicle speed display is showing a different speed than the analog vehicle speed display. There may be up to 2 miles per hour difference between the digital and analog vehicle speed displays. This is a normal condition due to the calculation tolerances being different for the two driver viewing angles for the analog speedometer; it may also appear to increase the difference between both displays. No part replacement is required as this is a normal operating characteristic of the vehicle. For CTS vehicles built between April and June of 2011 or the 2013 ATS, SRX, XTS built before August 29 2012 may have a 3 mile per hour or more variation. The technician is to replace the instrument panel cluster for this concern.
PIC6091
This Preliminary Information communication provides information to the technician with information on a customer concern of the windows roll down unwanted after suing the key fob. The vehicle could have remote venting windows. Normal operation of this feature is to hold the unlock button on the remote keyless entry transmitter until the windows start to roll down. If the unlock button is pressed again the windows will stop. The feature can be turned off if requested by the customer. For the CTS contact Techline to obtain a VCI number to disable the feature. For the XTS reprogram the body control module.
PIT5231C
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
PIC6055A
This Preliminary Information communication provides information to the technician about vehicle that may have a radio screen appears bubbled or is delaminating. Dealer can replace model years 2013 and 2014. If working on a 2015 model year vehicle dealer will need to contact General Motors Technical Assistance Center for further assistance. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
PI0091B
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
PIE0333A
This engineering information bulletin is requesting information from dealers on a customer concern of Low Tire Pressure indicator illuminated and/or slow loss of tire pressure.
02-08-42-001H
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
11-08-49-001O
This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.
15-00-89-004
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
PIC5779F
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIC5839C
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIC6086
This Preliminary Information communication provides information to the technician about vehicles that may have an oily substance is found on the inside windshield surface and appears to be leaking from the rear view mirror area. Technician should inspect the moisture sensor for being the source of the leak, if found to be leaking, carefully remove the moisture sensor. Clean the glass surface and sensor bracket with an isopropanol alcohol wipe until the surfaces are clean, then re-install the moisture sensor.
PIC6054A
This Preliminary Information communication provides information to the technician about vehicles that may have an intermittent delayed radio display operation when first starting vehicle if doors are left unlocked. Technician should not replace any parts for this concern. Technician should contact General Motors Technical Assistance Center for further assistance.
PIE0333
This engineering information bulletin is requesting information from dealers on a customer concern of low tire pressure indicator illuminated and/or a slow loss of tire pressure.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5282
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
PIT5231B
This Preliminary Information communication provides information to the technician about vehicles that may have a blank radio display. Technician may find a Diagnostic Trouble Code U150F stored in the Radio / Heater-Vent-Air Conditioning controls. Technician will verify if the correct display is installed. If the Diagnostic Trouble Code is current inspect the circuit form end to end.
PIT5411B
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP5090G
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician may find that the right front axle shaft is not fully seated into the transfer case. Technician will need to inspect the splines on the half shaft for damage. If damage is found replace the half shaft and install a new retaining ring with part number 90223082. When the half shaft does not have damage to the splines technician should replace the retaining ring with part number 90223082.
15-00-90-002
This informational bulletin provides information to service personnel on the critical importance of installing the correct replacement spin-on oil filter when servicing.
05-08-46-009D
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S. and Canada only).
PIT5285A
This Preliminary Information communication provides information to the technician about vehicles that may have a radio display does not always return to the previous call/source screen when a Bluetooth call has ended and/or that the call timer may continue to flash and increment. The call/source screen staying displayed is a normal operating characteristic and cannot be changed. Technician should updated the Human Machine Interface to prevent the call timer from flashing and incrementing after the call has ended.
PIP4919D
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIP5146A
This Preliminary Information communication provides information to the technician about vehicles that may have a bind or shudder on turns during tight parking lot maneuvers. If technician is working on a 2012 Lacrosse the Electronic Brake Control Module should be updated with the latest calibrations in Service Programming System. If the technician isolates the condition to be coming from the Rear Drive Module, then check the fluid level in the Rear Drive Module per Service Information. If fluid levels are incorrect then diagnose and repair as needed, review latest version of PI0703 if the differential clutch is overfull. If no fluid concerns are found change the differential clutch oil filter and oil. Technician should insure all oil and debris is removed from the differential.
PIC5161E
This Preliminary Information communication provides information to the technician about vehicles that the radio can be turned on after turning the ignition off and opening the driver?s door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
PIC6063A
This Preliminary Information communication provides information to the technician about vehicles that may have the park assist warning that goes off without an object near the vehicle. Engineering is aware of this concern and is working on a software change for this issue.
12-07-30-001E
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for Service Agents not required to contact PQC prior to assembly replacement.
13-08-116-001B
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
00-05-22-002O
This informational bulletin provides technicians with a brake lathe calibration procedure.
PIT5236C
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
PI1445
This preliminary informational bulletin provides repair information for a customer concern of Malfunction Indication Lamp (MIL) on, and a technician my find DTC P2227 set.
PIC6079
This Preliminary Information communication provides information to the technician about vehicles with remote start and the changes during a Remote Vehicle Start event as of the 2015 model year. The following functions have changed for 2015 Dual Zone Auto HVAC settings, Rear window defogger, heated seats, ventilated seats, and heated steering wheel. On transition to ignition the following Remote Vehicle Start event, the Heater-Vent-Air Conditioning settings will return to last known settings. During a remote start event, the rear window defogger will turn on if the outside temperature is 44 Fahrenheit (7 Celsius) or below. During a Remote Vehicle Start event, the heated seats will turn to the high setting when the ambient temperature is below 50 Fahrenheit (10 Celsius). During a Remote Vehicle Start event, the ventilated seats will turn to the high setting when the ambient temperature is above 80 Fahrenheit (27 Celsius). During a Remote Vehicle Start event, the heated steering wheel does not turn on.
12-06-01-003B
This informational bulletin provides information for repairing engine front cover oil leak, sealing surface preparation and applying RTV sealant.
13-00-89-008A
This informational bulletin communicates GM wiring repair strategy information.
PI1440
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.
04-00-89-015J
This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.
09-00-89-016D
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
12-06-01-008B
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
15-00-90-001
This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and filter.
02-07-30-029X
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
PIC6075
This Preliminary Information communication provides information to the technician about vehicles that navigation system has inaccurate estimated time of arrival. This is a normal operating characteristic of the New Generation Infotainment system.
PIT5411A
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PI1294A
This preliminary informational bulletin provides repair information on correcting a customer concern of intermittent service power steering message displayed on DIC, and DTC C056D, C0475 or U0131 may be set.
15-08-44-001
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6073
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
15-00-89-003
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).
PIC6070A
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-49903 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
05-06-04-060A
This informational bulletin communicates Information to technicians on control module Diagnostic Trouble Code(s) (DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.
11-08-49-001N
This technical bulletin is a revision for 11-08-49-001M to update the Condition.
PI1238C
This preliminary informational bulletin provides radio programming information to correct customer concerns about no XM on start-up when manually tuned and/or using voice recognition, no radio wake-up, rear view camera and OnStar handsfree calling issues, favorite stations stored twice and/or disappear.
PIC6070
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
PI1423
This preliminary informational bulletin provides Information for a technician noting a missing A/C refrigerant charge label on replacement front compartment front sight shield.
PIC6067
This Preliminary Information communication provides information to the technician about vehicles that may have a Diagnostic Trouble Code B101D sym 39 in the Human Machine Interface. Technician should not replace any parts for this concern.
PIT5264C
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIT5344A
This Preliminary Information communication advises the technician about vehicles that have an inoperative CD player. Technician should contact General Motors Technical Assistance Center if the concern is current and within four hours of the dealership. For dealers outside of this area, diagnose and repair as necessary.
08-03-10-004B
This informational bulletin communicates comprehensive instructions to GM Dealers and authorized GM Accessory Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.
05-00-89-055E
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
15-08-42-001
This informational bulletin communicates GM's position on exterior lighting components ?tinted or smoked? by an outside vendor.
PI1401A
This preliminary informational bulletin provides repair information to correct a customer concern of fuel gauge does not read full, only goes to 7/8 full.
PI1018A
This preliminary informational bulletin adds the 2015 model year to repair information on correcting a customer concern of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.
PIC5854D
This Preliminary Information communication provides information to the technician about vehicles that may have a the AM or FM audio volume changes, mutes, echoes, cuts in and out, repeats broadcast content, or skips intermittently. Advise this is normal operation when listening to a weak AM or FM HD station. Technician can shut the HD option off to fix the concern.
PIT5332A
This Preliminary Information communication advises the technician about vehicles that the HD turns on unwanted when tuning to radio stations using voice commands. General Motors Engineering is aware of concern and currently evaluating.
PIT5368
This Preliminary Information communication provides information to the technician about vehicles that iPhone is losing pair with the vehicle. Technician should delete the vehicle from the phone and the phone from the vehicle. Then perform a fresh pair between the iPhone and the vehicle.
05-03-10-020F
This informational bulletin communicates GM's position on use of nitrogen gas in tires.
PI1404
This preliminary informational bulletin provides a diagnostic tip for low line pressure or pressure regulator valve stuck after transmission service pump cover replacement.
PI1401
This preliminary informational bulletin provides repair information to correct a customer concern of the fuel gauge not reading full, only goes to 7/8 full.
PIT5367
This Preliminary Information communication provides information to the technician about vehicles that may have a blank displays, flashing displays, "Error or Update failed Messages", navigation map not loading, Bluetooth or USB concerns. Technician should inspect the USB/SD card port for a SD card or a device plug into any of the USB ports.
05-08-51-001G
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining when the protective shipping film is removed from certain vehicles.
01-00-89-010K
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using Customer Concern Verification Sheets (CCVS).
06-08-47-001K
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
00-03-10-002I
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.
PI1394
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIC5936D
This Preliminary Information communication provides information to the technician about vehicles that may have the Hazard Flashers turn on after vehicle shut down or that the Glove Box may be open when they return to their vehicle. Technician should replace the Hazard Switch and/or Glove Box Switch (depending on customers concern) with a new designed switch.
PIT3271G
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
03-06-03-003D
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
11-00-89-004A
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product field action customer reimbursement procedure (U.S. Dealers Only).
PIC3278F
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PI0360E
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar RemoteLink? phone application.
PI1126F
This preliminary informational bulletin provides repair information to correct customer concerns about blank screen after startup and reverse, rear view camera message on, touch screen inoperable, Bluetooth and navigation concerns.
03-00-91-001G
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
15-06-03-001
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PI1385
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always be re-learned when accessory wheels are installed on the vehicle.
030729004I
This informational bulletin was created for the Manual Transmission Operating Characteristics. The different noises caused by driver habit, weather conditions , and normal manual transmission noises.
PIT5236B
This Preliminary Information communication provides information to the technician about vehicle that may OnStar inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
14D133
Special Return - Fuel Tank Module Kit: ACDelco Part Number M10256 (select date codes)
PI0655A
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
PIP5209B
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIT5356
This Preliminary Information communication provides information to the technician about when listening to an iPod that the first song will still be displayed when the next song in the list is playing. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle and that the current song can be displayed by pressing the ?next? button while the device is playing.
PIC6054
This Preliminary Information communication advises the technician not to replace any parts and to contact General Motors Technical Assistance Center to report the concern and obtain a case number. Customer's display is slow to turn on when starting the vehicle if the doors were not locked.
PIC6055
This Preliminary Information communication provides information to the technician about vehicles that may have a radio screen appears bubbled or is delaminating. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
030848006J
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
This information provides the proper way to install the floor mats .
PI1126E
This preliminary information bulletin provides a procedure on reprograming the HMI module to repair the customers concern of the blank screen after start up, Rear view camera on, touch screen inop, bluetooth and navigation concerns.
100089005D
This warranty informational bulletin advised the technician that when performing a wiring repair, more information is required.
PI1371
This preliminary bulletin provides a procedure to update the active safety control module to correct the customers concern of the rea automatic brakes applying over curbs or objects near the ground or side.
PIT5236A
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
PI-1126-B
GM: SOME VEHICLES MAY EXPERIENCE A BLANK SCREEN AFTER STARTUP AND REVERSE, THE REARVIEW CAMERA MESSAGE MAY BE ON, AND THE TOUCH SCREEN BECOMES INOPERATIVE. THE BLUETOOTH AND NAVIGATION MAY BE MALFUNCTIONING. ALSO INCLUDES CHEVROLET SILVERADO MODEL YEAR 2015 AND GMC SIERRA MODEL YEAR 2015. *JS UPDATE 02/25/15*LJ
PI-1371
CADILLAC: WHEN OBJECTS ON GROUND NEAR REAR OF VEHICLE OR TO SIDE OR CURB, THE REAR AUTOMATIC BRAKING APPLIES WHILE BEING IN REVERSE AND AN UPDATED SOFTWARE CALIBRATION WAS RELEASED TO ADDRESS THE ISSUE. MODEL 2014-2015 XTS. *PE
PI1103E
This preliminary informational bulletin provides a procedure for the technician to test the power seats, the outside power mirriors, shorts in the wiring and the MSM, and reprogram the module if shorts weren't found, for the customers concern of the mirriors and/or seat inoperative.
PIT5074H
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
04-00-89-015I
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
06-00-89-026M
This warranty bulletin provides labor operation numbers for customer concerns that can't be duplicated.
PIC5492C
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
05-06-04-022L
This informational bulletin provides information on top tier fuels and what brands are available.
PIP5029F
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
10-08-98-002A
This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit.
99-04-20-002I
This informational bulletin explains a normal condition for what and how the drive line can clunk.
PI0778A
This preliminary bulletin provides a procedure to repair the glove box assembly to correct the customers concern of the glove box door electrical switch is inoperative, or that the glove box door latch releases on one side, but not the other.
09-06-04-026I
This informational bulletin was created to help technician identify non GM calibrations for the gasoline engines and the damages that may be caused by aftermarket calibrations
11-08-49-001M
This technical bulletin provides a procedure on how to turn the transport mode message of and reset the battery light flashing.
09-06-04-026H
This informational bulletin was created to help technician identify non GM calibrations for the gasoline engines and the damages that may be caused by aftermarket calibrations
PIT5344
This Preliminary Information communication provides information to the technician about vehicles with an inoperative CD player. Technician will need to contact General Motors Technical Assistance Center for further assistance.
PIT5264B
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
110849001M
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
990420002I
Information on Driveline Clunk Noise
PIE0287B
Engineering Information.
PIT5099A
A/C Blows Warm Or Poor Performance.
PIC6042
This Preliminary Information communication provides information to the technician about vehicles that if replacement of either shift paddle is necessary, the steering wheel does not need to be replaced nor does it need to be removed to replace either shift paddle.
14-00-89-003A
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and now is refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time
07-06-04-025K
This informational bulletin was provides information for the technician of cold start ticking noises in the engine compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
PIC5815A
This Preliminary Information communication provides information to the technician about vehicles that may have sit lower at being parked for several days. It is important to note that, under normal conditions, it is typical and acceptable for the air suspension system to drop slightly over time. Dealers can remind customers that cycling the ignition or starting the vehicle will bring the trim height back to normal levels.
PIT5320A
This Preliminary Information communication provides information to the technician about vehicles that the navigation voice feedback is choppy, distorted, or garbled. Technician will need to press Settings, Voice, Audio Feedback Speed, and verify speed is set to Medium.
PIT5411
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
06-08-43-003E
This informational bulletin explains how to care for wiper blades.
PIP5232A
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
04-00-89-015H
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
PIC6034
This Preliminary Information communication provides information to the technician that when the vehicle is shut off while the radio is off and the analog clock is displayed, the radio will turn back on with muted audio if the customer restarts the vehicle. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT5332
This Preliminary Information communication advises the technician about vehicles that the HD turns on unwanted when tuning to radio stations using voice commands. General Motors Engineering is aware of concern and currently evaluating.
PI1098A
This preliminary bulletin provides a procedure on how to cold crank test a battery in a vehicle.
PIC5945B
This Preliminary Information communication provides information to the technician about vehicles that may have Driver Information Center pages do not retain settings after an ignition cycle. Technician will need to review the latest version of PI1212 then use Service Programming System to perform a USB update to the Instrument Panel Cluster.
PIC6036
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5090F
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician should replace the right hand axle shaft retaining ring using part number 90223082. Technician will need to inspect the splines on the half shaft for damage.
04-06-04-047M
This informational bulletin states that it no longer valid and refers to a new bulletin.
08-08-44-015E
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIP5090E
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician should replace the right hand axle shaft retaining ring using part number 90223082. Technician will need to inspect the splines on the half shaft for damage.
PIC6029
This Preliminary Information communication provides information to the technician about vehicles that the rear Heater-Vent-Air Conditioning does not retain the temperature settings after a key cycle. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP5226
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
This informational bulletin provides information on how to use floor mats.
05-06-04-022K
This informational bulletin provides information on top tier fuels and what brands are available.
10-08-44-006C
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.
11-08-49-001L
This technical bulletin provides a procedure on how to turn the transport mode message of and reset the battery light flashing.
PIP5223
This Preliminary Information communication advises the technician that the Engine Control Module part number 12662034 is on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PI1103D
This preliminary informational bulletin provides a procedure for the technician to test the power seats, the outside power mirriors, shorts in the wiring and the MSM, and reprogram the module if shorts weren't found, for the customers concern of the mirriors and/or seat inoperative.
07-00-89-036G
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
02-00-89-002N
This informational bulletin provides additional information to the technicians and how to submit a field product report.
10-00-89-006E
This information bulletin provides the dealers on how to submit a product information report.
PIP5109F
This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 and 12662034 placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIT4911Y
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC5891C
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
110849001L
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
14471
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC6024
This Preliminary Information communication provides information to the technician about vehicles that will not connect to OnStar. Technician may find Diagnostic Trouble Code B2470-04 set in the Vehicle Communication Interface Module also a red LED on the OnStar keypad will be on. Technician will need to follow published diagnostics for the Diagnostic Trouble Code. If the diagnostics lead to replacement of the Vehicle Communication Interface Module read the OnStar Customer Identifier using Global Diagnostic System 2. If the value falls in range the technician will need to remove power from the module for 5 minutes. After the power cycle was performed, check for the Diagnostic Trouble Code to be set current or history. If the Diagnostic Trouble Code is current replace the module. If the Diagnostic Trouble Code is history no further action is required.
PIC5891B
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
03-06-03-004M
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
09-00-89-002J
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
PI1126D
This preliminary information bulletin provides a procedure on reprograming the HMI module to repair the customers concern of the blank screen after start up, Rear view camera on, touch screen inop, bluetooth and navigation concerns.
PI0653B
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers.
PI1296
This preliminary bulletin provides additional diagnoses for engine misfires, popping noise after cylinder head or fuel rail repair.
00-03-10-006K
This informational bulletin provides the technician with information on tire radial force variations and how to use it.
PIP5209A
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
PIP5216
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PI1294
This preliminary bulletin provides a procedure to check the EPS power and ground and reprogram the p/s module to correct the customers concern of the Intermittent Service Power Steering message on.
PI1238B
This preliminary bulletin provides a procedure to update the radio to correct the customers concern of multipul radio operation issues.
PIT3099M
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1290
This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose mirrior and/or bracket fell off.
PIC5854C
This Preliminary Information communication provides information to the technician about vehicles that may have a the AM or FM audio volume changes, mutes, echoes, cuts in and out, repeats broadcast content, or skips intermittently. Advise this is normal operation when listening to a weak AM or FM HD station. Technician can shut the HD option off to fix the concern.
13-02-32-001C
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.
PI-1294
BUICK/CADILLAC/CHEVROLET: AFTER A COLD START, MESSAGE IS DISPLAYED REGARDING INTERMITTENT SERVICE POWER STEERING AND NEED TO BE CHECKED. MODEL 2012-14 LACROSSE, 2014 REGAL, XTS, IMPALA. *PE
PIP-5216
BUICK/CADILLAC/CHEVROLET/SATURN/PONTIAC/ GMC: VEHICLE EXPERIENCE LOWER END SQUEAK OR SQUEAL, KNOCKING NOISE OR SEIZED ENGINE POSSIBLY THE MAIN BEARING OR ROD HAD FAILED. *PE
PIC5959B
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
99-01-39-004F
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
PIC4310J
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC5759A
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4911X
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
00-06-01-012E
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
12-03-10-001B
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
12-09-41-002B
The informational bulletin explains how items on the passenger seat may cause the PPS to chime or the passenger airbag light turns on if electronic devices or conductive objects are placed on the seat.
PIC5214D
This Preliminary Information communication provides information to the technician about vehicles that may have wheels that are collecting an excessive amount of brake dust. Dealer should advised the customer that This is considered a normal characteristic.
PIC5945A
This Preliminary Information communication provides information to the technician about vehicles that may have a Driver Information Center pages do not retain settings after an ignition cycle. Technician can reprogram the Instrument Panel Cluster on 2014 model year vehicle using Service Programming System. For model years 2013 General Motors Engineering is aware of the issue and is working towards a resolution.
PI1103C
This preliminary informational bulletin provides a procedure for the technician to test the power seats, the outside power mirriors, shorts in the wiring and the MSM, and reprogram the module if shorts weren't found, for the customers concern of the mirriors and/or seat inoperative.
PIP5163A
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
02-00-89-002M
This informational bulletin provides additional information to the technicians and how to submit a field product report.
PI0938A
This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic control issues.
PIP5109E
This Preliminary Information communication advises the technician that the Engine Control Module part numbers 12656993 and 12662034 are on part restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
10-00-89-006D
This information bulletin provides the dealers on how to submit a product information report.
07-06-04-025J
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment may be caused by the fuel pump and/or the fuel injectors and no
10-08-46-001B
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
PIC6013
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure.
PIP4902H
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
120941002B
Passenger Presence System (PPS) May Command Seat Belt Reminder Chime Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
14-00-89-003
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.
PI1212A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI1285
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5936C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5954A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5231A
This Preliminary Information communication provides information to the technician about vehicles that may have a blank display. Technician may find a Diagnostic Trouble Code U150F set. Technician will need to inspect circuit 7527 for damage if the Diagnostic Trouble Code is current.
PIT5304
Integrated Center Stack Display Delaminating Distorted Or Appears Cracked Behind Lens.
Recalls
Vehicle Recalls
PIP5209
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
050308002F
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
080849018E
This technical bulletin provides a procedure on cleaning scratches or scuffs on the interior trim or console panels using GM authorized polishes and waxes and advising that any damage may not covered by warranty.
PI1266
This preliminary bulletin explains to the technician to use the vin when reprogramming the radio using the techline/service programming systems.
PI0373B
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
PI0917D
This preliminary informational bulletin provides information on applying the correct amount of copper paste to the brake pad to correct the customers concern of a brake squeal or noise.
PIC5088E
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.
PIC5588B
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
05-00-89-029C
This preliminary bulletin provides a information to the dealer for the requirements need for equipment.
PI1126C
This preliminary information bulletin provides a procedure on reprograming the HMI module to repair the customers concern of the blank screen after start up, Rear view camera on, touch screen inop, bluetooth and navigation concerns.
12-00-89-002B
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
03-00-89-006K
This information bulletin provides dealers with more information on how to better prep a vehicle for pre-delivery.
14378
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIE0287A
Engineering Information.
09-03-10-013B
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
02-07-30-029W
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
12-07-30-001D
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
03-06-03-004L
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.
00-03-10-006J
This informational bulletin provides the technician with information on tire radial force variations and how to balance a tire using the balancer.
03-03-10-007I
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
PI1238A
This preliminary bulletin provides a procedure to update the radio to correct the customers concern of multipul radio operation issues.
12-08-132-001B
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the cause if diagnostics finds no problems to that point.
13-00-89-004I
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIC5428F
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
06-00-89-029J
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
PI1242
This preliminary bulletin provides a procedure to re-calibrate the forward range radar if the Service Driver Assist message stays on after a repair.
PI1238
This preliminary bulletin provides a procedure to update the radio to correct the customers concern of multipul radio operation issues.
14-08-117-001
This technical bulletin provides a procedure to disconnect the battery if the repairs were done to the vehicle and the technician was unable to clear the codes.
PI1235
This preliminary bulletin provides information to the technician, to check for loose grounds and the correct labor op to use
PI1233
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint concerns when trying to locate a root cause.
PI1234
This preliminary bulletin explains a normal noise from the turbochargers when the vehicle is revved in P or D.
05-06-04-035D
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
02-07-30-029V
This informational bulletin provides information to the technician on what parts of an engine or transmission will require the PQC to be notified.
PIP5062C
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
PIT5283
This Preliminary Information communication provides information to the technician about vehicles that have a touchscreen that is inaccurate or that the display does not seem to respond with the desired operation when pressed. Technician will need to perform a touch screen calibration and re-evaluate the concern.
11-08-49-001K
This technical bulletin provides a procedure on how to turn the transport mode message off and reset the battery light flashing.
110849001K
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
1408117001
Unable to Clear BCM DTCs After Completing Repair
PI-1235
GENERAL MOTORS: DUE TO LOOSE GROUND TERMINAL CONNECTIONS, IN SOME VEHICLES AND TRUCKS EXPERIENCE, ACCESSORIES MALFUNCTIONS, DIC MESSAGES, IPC WARNING INDICATORS, SES LIGHT ON. *PE
PI1103B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5996
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5285
Call Screen Is Still Displayed After Ending A Bluetooth Call
09-00-89-002I
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
PIP4919C
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
01-08-42-001J
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
09-00-89-029L
This informational bulletin explains how to cut a new key or how to get a precut key from GM.
PIC5991A
This Preliminary Information communication provides information to the technician about vehicles that have the outgoing end of a Bluetooth call may have static that lasts for a short period of time when beginning a Bluetooth call, or when transferring a phone call from a handset to handsfree using the vehicle?s Bluetooth. Dealer should advise the customer the first 5-10 seconds of audio quality after the transfer can be "poor" on the outbound side. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP5194
This Preliminary Information communication provides information to the technician about vehicles that have random misfires or roughness on cold start. Technician will need to fill the vehicle with fresh fuel and test drive for 20 miles. If the roughness or random misfire is gone then no further repairs should be attempted. If the Service Engine Soon light is on or flashing, after filling with fresh fuel and operating the vehicle as described, the spark plugs may need to be inspected for fouling and replaced as needed.
PIP5191
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIC5491F
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIC5991
This Preliminary Information communication provides information to the technician about vehicles that have the outgoing end of a Bluetooth call may have static that lasts for a short period of time when beginning a Bluetooth call, or when transferring a phone call from a handset to handsfree using the vehicle?s Bluetooth. Dealer should advise the customer the first 5-10 seconds of audio quality after the transfer can be "poor" on the outbound side. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIT3099L
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1159C
This preliminary bulletin provides a procedure to reprogram the radio to correct the customers concern of XM issues, rear view camera issues and favorite stations stored twice and/or disappears.
PI1187A
This preliminary bulletin provides a repair to replace the windshield to fix the customers concern of the inside rearview mirrior loose or fell off with bracket.
13-00-89-004H
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
PIC5779E
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PI1212
This preliminary bulletin explains the proper way to update and complete the IPC updates
SB-0000189297-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
130089004H
Car and Truck Fix it Right the First Time Issues
1406130001
High Voltage Safety ? High Voltage Disabling
14062A
Brake Booster Pump ? Cavity Plug
PIP-3423-K
GM: SOME DTC CODES MAY BE SET, P0016, P0017, P0018, P0019, P0008, OR P0009. 3.6 LY7 WITH CAM ACTUATOR DTC.THE RELUCTOR FOR THE CRANKSHAFT SENSOR PRESSED ON THE CRANKSHAFT MAY HAVE MOVED. ALSO INCLUDED BUICK ALLURE MODEL YEAR 2005. *JS
PIT4911W
Navigation Radio, Radio, Amplifier, Human Machine Interface.
03-06-03-004K
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not
PIP3423K
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
PIC5854B
This Preliminary Information communication provides information to the technician about vehicles that may have a the AM or FM audio volume changes, mutes, echoes, cuts in and out, repeats broadcast content, or skips intermittently. Advise this is normal operation when listening to a weak AM or FM HD station. Technician can shut the HD option off to fix the concern.
PIT5268
This Preliminary Information communication advises the technician that some vehicles may have a radio display that is covered when the radio station favorites list is maximized. This is a normal operating characteristic and no repair attempt should be made. The hidden screen functions will operate again after the user minimizes the favorites list by dragging it to the bottom of the display.
PIP5139A
This Preliminary Information communication advises the technician that the Cadillac XTS 3.6 (LF3) Twin Turbo Charger Restriction on the Turbocharger Part number 12658828 has ended. Dealer can now order the Turbocharger can now be ordered through the regular Customer Care and Aftersales parts process.
SB-0000187967-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
13-00-89-004G
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
SB-0000187696-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5109D
This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 will be placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
SB-0000187283-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5374C
This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.
PIC5936B
This Preliminary Information communication provides information to the technician about vehicles that may have the Hazard Flashers turn on after vehicle shut down or that the Glove Box may be open when they return to their vehicle. Technician should replace the Hazard Switch and/or Glove Box Switch (depending on customers concern) with a new designed switch.
PIC5959A
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIT5264
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIC4801F
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
110849001J
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
130089004G
Car and Truck Fix it Right the First Time Issues
14062
PSR - Brake Booster Pump - Cavity Plug
PI1187
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5129B
Engine Exchange Program for 2014 Model Year Has Ended.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIC4921C
This Preliminary Information communication provides information to the technician on a proper paint code for the following special addition vehicles. 2003 Mary Kay Cadillac models - use paint code WA-160E - Mary Kay Pink Pearl 2004 - 2007 Mary Kay Cadillac models - use paint code WA-983L - Mary Kay Pink Pearl III 2004 Neiman Marcus Cadillac XLR - use paint code WA-111B - Majestic Amethyst Metallic 2008 - 2015 Mary Kay Cadillac models - use paint code WA-590Q - Mary Kay Pink Pearl V 2011 Neiman Marcus Chevrolet Camaro convertible - For the exterior body color, use paint code WA-724S - Mystic Bronze Tri-coat. For the ghost stripes on the hood and deck lid, use paint code WA700T 2013 Hot Wheels Chevrolet Camaro - For the exterior body color, use paint code WA-720S - Kinetic Blue. For the red stripe on the wheels and the front bumper, use paint code WA-799U - Performance Red.
11-08-49-001J
This technical bulletin provides a procedure on how to turn the transport mode message of and reset the battery light flashing.
PIC3011H
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
PIC5491E
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
12-07-30-001C
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
09-03-10-016B
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
10-08-64-002C
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
12-03-10-001A
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
12-03-10-002A
This informational bulletin provides the technician the proper way to install and torque the wheel.
PI0737A
This preliminary bulletin provides information on how to set the rear electric child locks.
PIC5968
This Preliminary Information communication provides information to the technician about vehicles that may have map view will change to the North Up view on its own when zoomed out more than 25 miles (40 km). Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
14-00-89-002
This informational bulletin addvises a technician to remove a 20 amp fuse in cavity 41 and replace it with a 25 amp fuse.
PI1159B
This preliminary bulletin provides a procedure to reprogram the radio to correct the customers concern of XM issues, rear view camera issues and favorite stations stored twice and/or disappears.
05-03-10-020E
This informational bulletin explains the use of Nitrogen in GM tires.
07-03-10-008D
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and recommended practices.
08-03-10-006E
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.
03-08-46-004O
This informational bulletin provides information on part restriction and ordering of Onstar vehicle communication modules.
13-00-89-004F
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
SB-0000185722-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC4921B
This Preliminary Information communication provides information to the technician on a proper paint code for the following special addition vehicles. 2003 Mary Kay Cadillac models - use paint code WA-160E - Mary Kay Pink Pearl 2004 - 2007 Mary Kay Cadillac models - use paint code WA-983L - Mary Kay Pink Pearl III 2004 Neiman Marcus Cadillac XLR - use paint code WA-111B - Majestic Amethyst Metallic 2008 - 2015 Mary Kay Cadillac models - use paint code WA-590Q - Mary Kay Pink Pearl V 2011 Neiman Marcus Chevrolet Camaro convertible - For the exterior body color, use paint code WA-724S - Mystic Bronze Tri-coat. For the ghost stripes on the hood and deck lid, use paint code WA700T
PIT4943C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIT4945F
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
02-08-98-002E
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
05-08-48-001D
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a windshield.
99-01-39-004E
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
PIT5076D
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIP5180
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
PIT5252A
This Preliminary Information communication provides information to the technician about vehicles that have an inoperative RKE operation and the horn/wipers will be stuck in the "on" position. Technician may find Diagnostic Trouble Code B101D sys F0 set in the Body Control Module. Technician should clear the Diagnostic Trouble Code. If the B101D SYM F0 resets ensure the Body Control Module is awake open the driver?s door then disconnect the battery, wait 5 seconds, then reconnect battery. If the BCM outputs remain active and the Remote Keyless Entry is non-functional, then the Body Control Module should be replaced.
PIT5252
This Preliminary Information communication provides information to the technician about vehicles that have an inoperative RKE operation and the horn/wipers will be stuck in the "on" position. Technician may find Diagnostic Trouble Code B101D sys F0 set in the Body Control Module. Technician should clear the Diagnostic Trouble Code. If the B101D SYM F0 resets ensure the Body Control Module is awake open the driver?s door then disconnect the battery, wait 5 seconds, then reconnect battery. If the BCM outputs remain active and the Remote Keyless Entry is non-functional, then the Body Control Module should be replaced.
PIC5453A
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PI0917C
This preliminary informational bulletin provides information on applying the correct amount of copper paste to the brake pad to correct the customers concern of a brake squeal or noise.
130089004F
Car and Truck Fix it Right the First Time Issues
140089002
Important Fuse Replacement Requirement
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
990139004E
Air Conditioning Odor
990851007F
Refinishing Aluminum Wheels
PIC5161D
Key Off Radio Operation.
PIE0285
Engineering Information.
PIE0287
Engineering Information.
04-00-89-053F
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
PIC5959
This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
11-00-89-002B
This informational bulletin was created to inform that any accessories that are install from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
PIP4670D
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP4919B
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
PIC5953
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP4924D
This Preliminary Information communication provides information to the technician about vehicles that have Service Engine Soon Malfunction Indicator Lamp on and a misfire. Technician may find Diagnostic Trouble Codes P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264, P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, P0277, P2146, P2149, P2152, P2155, P216A, and or P216D. Technician will need to inspect the fuel injector wiring harness for rub through or internal wire opens. If this concern is found repair or replace the injector harness as needed.
07-06-04-025I
This informational bulletin was provides information for the technician of cold start ticking noises in the engine compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
PIP4112N
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
PIP3140F
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP4384H
This Preliminary Information communication provides information to the technician with a supplement to the Service Information timing procedure for the high feature V-6 engine. Technician will also review the training video on the Common Training Website.
PIP4964C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
08-08-44-029D
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
PIC5936A
This Preliminary Information communication provides information to the technician about vehicles that may have the Hazard Flashers turn on after vehicle shut down or that the Glove Box may be open when they return to their vehicle. Technician should replace the Hazard Switch and/or Glove Box Switch (depending on customers concern) with a new designed switch.
04-00-89-015G
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
PIP4919A
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
14-00-89-001
This warranty administration bulletin provides information on Premium care maintenance eligibility for vehicle services and maintenance in the U.S. and Canada.
04-00-89-015F
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
07-00-89-037G
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to its customers.
140089001
Cadillac Premium Care Maintenance Eligibility for United States and Canadian Vehicles
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PI0949A
Required Programming for Cadillac Professional Vehicle Applications To configure the vehicle for proper operation of the electronic suspension control system (ESC), the following procedure must be performed.
PI1159
No XM Audio, Rear View Camera Issues, Favorite Stations Stored Twice and/or Disappear Condition/Concern No audio on startup in XM. iPhone does not detect if user disconnects iPhone during certification process. When receiving an incoming call through OnStar Hands Free Calling system, the vehicle does not ring. It will show on the screen. FM Timeshift not functioning properly. HD Switching Toggle Setting does not function. Favorites stored Twice or disappear. Noise is played during the TimeShift recoding. A/C Mode icon is displayed when vehicle is not equipped with A/C. The folder track is not played when the folder is pressed for a long time. Missing Forward Collision Warning Chime on vehicles base audio system, Forward Collision Alert and/or Adaptive Cruise. Long press of the knob when highlighting a browse folder, sometime changes the media source from SD card to USB and when user releases the push knob, it brings the Media Menu back instead of showing the now playing screen for USB and SD card. The USB only works with Apple products (iPhone). Rear view camera issues.
PI1159A
No XM Audio, Rear View Camera Issues, Favorite Stations Stored Twice and/or Disappear Condition/Concern No audio on startup in XM. iPhone does not detect if user disconnects iPhone during certification process. When receiving an incoming call through OnStar Hands Free Calling system, the vehicle does not ring. It will show on the screen. FM Timeshift not functioning properly. HD Switching Toggle Setting does not function. Favorites stored Twice or disappear. Noise is played during the TimeShift recoding. A/C Mode icon is displayed when vehicle is not equipped with A/C. The folder track is not played when the folder is pressed for a long time. Missing Forward Collision Warning Chime on vehicles base audio system, Forward Collision Alert and/or Adaptive Cruise. Long press of the knob when highlighting a browse folder, sometime changes the media source from SD card to USB and when user releases the push knob, it brings the Media Menu back instead of showing the now playing screen for USB and SD card. The USB only works with Apple products (iPhone). Rear View Camera Issues: When shifting from Drive to Reverse is less than 3 seconds, the display will not transition to the rear view camera screen. When shifting from Drive to Reverse is more than 3 seconds, the display may be blank and will not show the rear view camera message Check Surrounding for Safety.
PIC5839B
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PI1126
This preliminary bulletin provides information on Blank Screen After Startup and Reverse, Rearview Camera Message On, Touch Screen Inoperable, Bluetooth® and Navigation Concerns
10-00-89-006C
This informational bulletin provides directions on submitting different PIRs
PIP5090D
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician should replace the right hand axle shaft retaining ring. Technician will need to inspect the splines on the half shaft for damage. Technician should also inspect the splined end of the Power Transfer Unit for excessive wear.
08-08-44-015D
This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.
13-00-89-004E
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
PI0917B
This preliminary bulletin provides a procedure to add a lubricate to the edges of the brake pad to correct the customers concern of brake noise on initial brake application.
PI0754A
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not replace any glass for this reason.
PIC5945
This Preliminary Information communication provides information to the technician about vehicles that the Driver Information Center settings do not stay at the setting they were left it after an ignition cycle. Technician will need to reprogram the Instrument Panel Cluster with the latest calibrations using Service Programming System and Tis2Web.
05-00-89-072C
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
13-08-43-002
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
130843002
Information on Windshield Multifunction Sensor Mount Bracket Cover Replacement
PIP-5090-D
GM: SOME VEHICLES MAY EXPERIENCE A VIBRATION OR SHUDDER UPON ACCELERATION FROM A STOP. THE RIGHT FRONT AXLE SHAFT MAY NOT B FULLY SEATED INTO THE PTU. *JS
12-06-01-003A
Service bullentin information for repairing engine front cover oil leak, sealing surfaces preparation, applying room temperature vulcanizing (RTV) sealant.
PI0592C
This preliminary bulletin provides information on Service Programming System (SPS) Errors (E4398, E4399, E4403, E4404, E4413, E4414, E4423 or E4491).
13-00-89-004D
This informational bulletin provides an update for 13-00-89-004C to include updated information.
PIC5936
This Preliminary Information communication provides information to the technician about vehicles that may have the Hazard Flashers turn on after vehicle shut down or that the Glove Box may be open when they return to their vehicle. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
00-06-01-026E
This informational Bulletin provides a revision for 00-06-01-026D to add the 2014 model year.
PIP5029E
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PI0018B
This preliminary bulletin provides a pre-inspection symptom list before preforming any repairs to any of windows for noises or performance.
04-06-04-047L
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
PI1103
This preliminary bulletin provides a procedure to reset the memory seat module and GM is working on a solution for the customers concern.
PI1098
This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.
PIP5129A
This Preliminary Information communication advises the technician that the 3.6L LF3 Twin Turbo Charged Engine will be placed on engine exchange program. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIT4911V
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
09-06-04-015B
This informational bulletin provides a revision for 09-06-04-015A to add the 2012-2014 model years.
10-08-110-001A
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
130089004D
Car and Truck Fix it Right the First Time Issues
PI-0018-B
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
PIC5932
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIP5163
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5862
This Preliminary Information communication provides information to the technician about vehicles that have brake lights remain on with the vehicle off and parked and/or the vehicle battery goes dead. Technician will need to inspect for aftermarket parts.
PIP5158
This Preliminary Information communication advises the technician that the turbocharger part numbers 12659010 and 12659010 have been placed parts restriction by General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIC5854A
This Preliminary Information communication provides information to the technician about vehicles that may have a the AM or FM audio volume changes, mutes, echoes, cuts in and out, repeats broadcast content, or skips intermittently. Advise this is normal operation when listening to a weak AM or FM HD station. Technician can shut the HD option off to fix the concern.
PIT5237
This Preliminary Information communication provides information to the technician about vehicles that the Pandora audio will revert back to the phone after a Bluetooth call when an iPhone is connected to the vehicle via USB. Technician should cycle the USB connection and the concern will be resolved. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIP4959D
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
PIC5491D
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIC5492B
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIP5095B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIT5236
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
110849001I
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
130089004C
Car and Truck Fix it Right the First Time Issues
130089010
PAC Courtesy Transportation Assistance Program
PI1072
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI1089
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT3237G
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
PIP5109C
This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 will be placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIP5062B
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have check engine light and a misfire. Technician will find a P0300 set. If the misfiring cylinder is creating NO or very low power, technician will need to follow these diagnostics steps. 1) Swap the ignition coil and spark plug with another cylinder. 2) Inspect the plug when out for wet or dry condition. 3) Perform an injector test with a scan tool. 4) If the plug is wet then check for a leaking or stuck open injector. 5) If the plug is dry then enrich the intake air with propane. If the severity of the misfire is less with enrichment, suspect a weak or inoperative injector driver in the Engine Control Module and replace as needed. 6) Perform a cylinder leakage test to determine if there is a valve sealing concern. If there is a valve sealing concern see the latest version of PIP5029 for recommendations.
PIP5090C
This Preliminary Information communication provides information to the technician about vehicles that may have a noise, vibration or shudder on acceleration from a stop. Technician should replace the right hand axle shaft retaining ring. Technician will need to inspect the splines on the half shaft for damage. Technician should also inspect the splined end of the Power Transfer Unit for excessive wear.
PIP5109B
This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 will be placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
PIC5491C
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
PIC5779D
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIC5891A
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
PIT3099K
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
990940005G
Seat Belt Extender Availability
PIE0269
Engineering Information.
PIT4911U
Navigation Radio, Radio, and Integrated Center Stack.
03-08-46-004N
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM).
01-03-10-003K
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.
06-00-89-026L
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
G-173287
13275 - Service Update. Inspect the routing of the turbo vacuum hoses and, if necessary, reroute the hoses and replace any that are damaged. The hose on some of these vehicles may be routed incorrectly. This could cause the turbo wastegate to remain open, reduce engine power at high throttle openings, and the illumination of a MIL light at the first instance of operation demanding turbo boost.
PIP5109A
This Preliminary Information communication advises the technician that the Engine Control Module part number 12656993 will be placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
SB-13275
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5822A
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
PIC5892A
This Preliminary Information communication provides information to the technician about vehicles that have display is blank, but audio may or may not be present. Technician will need to use Global Diagnostic System 2 to check the Surrogate MOST Master Node Upstream Position is stored in Radio Data Display. Also technician will need to gather more information and contact General Motors Technical Assistance Center for further assistance.
PIC5904
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
06-06-01-010B
This informational bulletin provides information on close-coupled converter and engine replacement.
PIP5029D
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
99-09-40-005G
This informational bulletin provides information on availability for the seat belt extender.
00-03-10-003R
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
PIP5139
This Preliminary Information communication advises the technician that the 2014 Cadillac XTS Equipped with 3.6L LF3 Turbocharged engine part number 12658828 will be placed on a parts restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
13275
Service Update for Inventory and Customer Vehicles Turbo-to-Exhaust Manifuld Joint May Relax Expires with Base Warranty
PI0561A
This preliminary information bulletin provides a procedure for replacing the right and left axle shaft seals to eliminate a squeak or chirp noise due to the lack of lubrication.
PI1036
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIP5129
Turbo Charged Engine Exchange Program
03-06-03-004I
This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.
PIC5887
This Preliminary Information communication provides information to the technician about vehicles that have one or more broken air suspension compressor mounting bracket bolts. Technician will need to replace the compressor assembly without disturbing the broken bolts as much as possible.
02-07-30-029U
This informational bulletin provides information for the PQC assembly replacement process.
PI1018
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
10-00-89-010C
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
11-08-49-001H
This technical bulletin provides a procedure to remove the transport mode on message displayed in the DIC.
13-00-89-008
This informational bulletin provides information for GM wiring repair.
10-00-89-009B
This informational bulletin provides information on key code security and information on GM key code look up applications.
110849001H
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
130089008
GM Wiring Repair Strategy Information
130090001
Information for Engine Oils Used in 2014 Model Year Vehicles
PIC5779C
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
09-00-89-029K
This technical bulletin provides a revision for 09-00-89-029J to add the 2014 model year and to add the Impala, Spark, Spark EV, Silverado and Sierra.
13-00-90-001
This technical bulletin provides information on Engine Oils Used in 2014 Model Year Vehicles
PI1009
This preliminary informational bulletin provides information for Diagnostic Tips for DTCs P0097, P00F4, P0113, P2229 and/or P0102 Set
04-00-89-015E
This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S. version of Bulletin 12-00-89-003.
03-00-89-006J
This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.
05-09-40-002G
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
12-09-41-002A
This technical bulletin provides information on a revision for 12-09-41-002 to add the 2014 model year and update the models.
07-08-49-020H
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
12-02-32-002A
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
110849001G
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
120941002A
Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
00-05-22-002N
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
PI0011C
This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update Warranty Information.
11-08-49-001G
This informational bulletin provides information for Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below) Condition.
13-00-89-006
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage Effective with 2010 Model Year.
PI0574A
This preliminary informational bulletin provides a revision for PI0574A to include the 2013-2014 model year vehicles, update the covered models and the Recommendation/Instructions section.
08-06-01-006D
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
PIT5214
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
11-00-90-001B
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
09-00-89-008A
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
PI0592B
This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.
07-03-10-015C
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.
05-08-48-001C
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
05-03-07-009F
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.
13-00-89-004B
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PIC5839A
This Preliminary Information communication provides information to the technician about vehicles that have a clock that is slow to update while driving. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
06-00-89-026K
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.
10-00-89-016A
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the Labor Operation graphic.
09-03-16-002B
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time Code and update the tool reference information.
09-07-30-018D
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.
PI0785B
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model and update the Parts and Warranty Information.
PIP4902G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
10-00-89-005C
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
11-00-89-007C
This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation List.
07-00-89-037F
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation under Courtesy Transportation Warranty Transaction Submission.
09-00-89-016C
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
03-08-48-006I
This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.
03-06-03-004H
This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.
090730018D
Change in Automatic Transmission Add Condition Documentation and Claim Submission
130089004B
Car and Truck Fix it Right the First Time Issues
PIT4720C
Odometer Servicing When The Odometer Cannot Be Set To The Actual Mileage.
PIT5074G
Terminal Test Probe And Replacement Terminal.
13-00-89-005
This technical bulletin provides Warranty Administration - New Labor Codes information.
11-08-49-001F
This technical bulletin provides a revision of 11-08-49-001E to add the 2014 model year.
PIC4707D
This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.
03-06-03-003C
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
99-04-20-002H
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
PI0572B
This preliminary information bulletin is for information on COAX Repair Kit Availability. Revised from PI0572A
110849001F
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below)
130089003
Vehicle Software Enhancements
130089005
New Global Labor Codes
990420002H
Information on Driveline Clunk Noise
13-00-89-003
This technical bulletin provides information on Vehicle Software Enhancements for 2014 and prior GM Passenger Cars and Light Duty Trucks.
11-00-89-005D
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
12-08-132-001A
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to electrical systems that can be affected by devices that are plugged in by the customer.
09-00-89-002H
This informational bulletin provides information for dealers to properly maintain vehicle in inventory.
PI0938
This preliminary information bulletin provides information on powertrain and various electronic/electrical control issues.
06-00-89-029I
This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats carpet, vinyl.
09-06-04-026G
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM (Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2® or global diagnostic system 2 (GDS 2)
SB-23124783-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1308116001A
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
PIP5094
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
990851001C
Paint-less Dent Repair Process
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.