PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
13-02-32-001H
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-223
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
21-NA-280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
18-NA-115
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC P0300 that may also be set.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
21-NA-147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminatedâ.
19-NA-256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
PIP4112T
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-02-32-001G
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
18-NA-263
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
21NA280
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running, Malfunction Indicator Lamp (MIL) Illuminated.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
19NA256
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
21NA147
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction Indicator Lamp (MIL) Illuminated?.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
21NA108
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine overheating, cooling system contaminated with engine oil.
PIP5257E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5180C
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
20NA026
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After an OnStar In-Vehicle Voice Message Is Heard.
PIP5095G
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
120232002B
This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
070604025M
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5257D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
18NA072
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
130601003J
This technical bulletin provides Correction information to find the cause of oil consumption. Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PI1300B
This preliminary informational bulletin provides technicians information on resetting the change transmission fluid message on Driver Information Center (DIC) after changing the transmission fluid.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
DOR-G9Z8V-12
This SKU is a Fuel Pump Driver Module. The customer communication requested return of unsold inventory to inspect the software. The software may have a fault where the readiness monitors are stuck in the not-ready or incomplete position. The readiness monitors will not cause performance or emissions issues but will prevent the emissions scanning tools from confirming the module is performing correctly, causing the vehicle to fail state required emissions tests.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
150844001J
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIP5257C
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
130232001F
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
130601003I
This technical bulletin provides Correction information to find the cause of oil consumption. Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
030729004L
This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
120601003C
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying RTV Sealant.
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP5191C
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
PIP5095F
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
PIP5257B
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
PIP5569
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIP4112S
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
PIP5095E
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PIP5180B
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
16NA075
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
130232001E
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
PIP4959G
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
16NA249
Low Audible Whine Noise has been found to be transmitting from the balance shaft drive chain.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PIP4959F
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
PIP5216F
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
PIP5191B
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
03-06-03-004U
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIP4112R
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
15-08-44-001I
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
PIP5095D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
02-00-89-002Q
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
01-03-10-003O
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
07-06-04-025L
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.
15-00-90-002A
This informational bulletin provides information on Installing the Correct Replacement Spin-On Oil Filter When Servicing.
PIP5180A
This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve. Technician will need to review the latest version of PIP5029 and perform a cold compression test if the concern is only a Hard Start Cold.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
99-00-89-019O
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
99-00-89-019N
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
01-03-10-003N
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
02-00-89-002P
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
04-06-04-051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIP5282A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
16NA241
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIP-3140-G
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT A NOISE OR A VIBRATION IN THE VEHICLE THAT SEEMS TO BE ABNORMAL MAY NOT HAVE BEEN THERE WHEN THE VEHICLE WAS PURCHASED. TECHNICIAN SHOULD LOOK FOR NON - GENERAL MOTORS AFTERMARKET ACCESSORIES INSTALLED ON THE VEHICLE THAT CAN CAUSE THESE ISSUES.
SB-02-07-30-029Z
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
SB-16NA-131
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIT5485B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIP5168E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
SB-10-08-46-001C
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
SB-16-NA-119
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-16-NA-117
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
PIT5485A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PI-0281-E
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
SB-16-NA-109
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.
PIP5093B
Some customers may complain of an engine oil leak that appeared as they were driving the vehicle in extremely cold ambient temperatures (Generally 0 F /-17 C or Colder). They may also comment that they heard a single "pop" noise right before the oil leak started. Upon inspection, the technician will find that the oil leak is coming from the rear main oil seal of the engine as shown below. This may be the result of a frozen PCV system and excessive crankcase pressure. If a leaking rear main oil seal is found in warmer climates, this PI does not apply.
PIP5257
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE OIL MIXED IN WITH THE ENGINE COOLANT. TECHNICIAN WILL NEED TO INSPECT THE OIL COOLER IF EQUIPPED FOR POSSIBLE LEAKING INTO THE COOLING SYSTEM THROUGH THE RADIATOR. IF NO ISSUE FOUND REPLACE THE ENGINE AS WELL AS ALL RUBBER COOLANT HOSES.
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
130232001D
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
OnStar Voice Fallback Number Update
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5216C
If a vehicle comes into the dealership with a knock noise, seized engine, lower end squeak or squeal or any condition that you suspect a rod or main bearing failure.
PIT3271G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT CHANGING THE TIRE AND WHEEL SIZE ON VEHICLES. GENERAL MOTORS WILL ONLY SUPPORT A TIRE CALIBRATION FOR TIRES THAT HAVE BEEN SIZED, TESTED AND DESIGNED FOR THE VEHICLE IN QUESTION AND ITS APPLICATIONS. TECHNICIAN SHOULD NOT USE THE INFORMATION THAT IS PROVIDED BY THE ANTILOCK BRAKING SYSTEM TIRE SIZE SELECTION.
PIC3278F
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.
PIT5074H
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
PIT5236B
OnStar Module Does Not Support All B101D Symptom Codes.
990420002I
Information on Driveline Clunk Noise
PIT5099A
A/C Blows Warm Or Poor Performance.
PIT5264B
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
PIT5353
XM Audio Traffic And Travel Link Availability And Operation.
PIP-5096
CADILLAC/BUICK/CHEVROLET/GMC: DUE TO CAM ACTUATOR CODES SET - DTC P0011, DTC P0014, DTC 20024, DTC P0021 AND NO OTHER DRIVABILITY ISSUES, THE ENGINE EUN STICKER SHOULD BE INSPECTED, BEFORE REPLACING ACTUATOR. *PE
PIP-5216
BUICK/CADILLAC/CHEVROLET/SATURN/PONTIAC/ GMC: VEHICLE EXPERIENCE LOWER END SQUEAK OR SQUEAL, KNOCKING NOISE OR SEIZED ENGINE POSSIBLY THE MAIN BEARING OR ROD HAD FAILED. *PE
SB-13-02-32-001
BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE
Recalls
Vehicle Recalls
090845004D
Implementation of Logistics Fuse - Additional Pre-Delivery Inspection (PDI) Steps and Inventory Considerations
PI-1235
GENERAL MOTORS: DUE TO LOOSE GROUND TERMINAL CONNECTIONS, IN SOME VEHICLES AND TRUCKS EXPERIENCE, ACCESSORIES MALFUNCTIONS, DIC MESSAGES, IPC WARNING INDICATORS, SES LIGHT ON. *PE
PIC5687D
Checking Smartphone Bluetooth Software Update Status
130089004H
Car and Truck Fix it Right the First Time Issues
1406130001
High Voltage Safety ? High Voltage Disabling
PI1192
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIC5687C
Checking Smartphone Bluetooth Software Update Status
PIC5959A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT4864F
Information On Requests To Add OnStar Bluetooth Option.
PIT5264
Canadian Customers Unable To Place Calls In The United States
99-08-51-007F
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PI0281D
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
PI-0324-C
GMC/CHEVROLET/BUICK: TRANSMISSION PUMP NEEDS INSPECTING DUE TO ENGINE CRANKING BUT FAILS TO START, HAS NO FORWARD, NO REVERSE, TRANSMISSION LEAKS, HARD SHIFT AND NO CRANKING. *PE UPDATED 2/25/13. *PE UPDATED 1/29/2014 *JS
130089004D
Car and Truck Fix it Right the First Time Issues
PI-0018-B
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
130089004C
Car and Truck Fix it Right the First Time Issues
130089010
PAC Courtesy Transportation Assistance Program
990940005G
Seat Belt Extender Availability
PIT5138C
Remote Keyless Entry Functions Are Inoperative When The Ignition Key Is Off.
130089008
GM Wiring Repair Strategy Information
130090001
Information for Engine Oils Used in 2014 Model Year Vehicles
130232001B
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
130232001A
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
090730018D
Change in Automatic Transmission Add Condition Documentation and Claim Submission
130089004B
Car and Truck Fix it Right the First Time Issues
130232001
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions
PIT5214
GM TAC Support of Vehicle Vibration Complaints.
09-08-45-004C
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
090845004C
Implementation of Logistics Fuse - Additional Pre-Delivery Inspection (PDI) Steps and Inventory Considerations
130089003
Vehicle Software Enhancements
130089004
Car and Truck Fix it Right the First Time Issues
130089004A
Car and Truck Fix it Right the First Time Issues
SB12-08-132-001A
GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE
1308116001A
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
PI0412B
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
PIP2096
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT5197
Heated Seats Inoperative After Replacing The Heated Seat Control Module.
PIT5197A
Heated Seats Inoperative After Replacing The Heated Seat Control Module.
PI0881
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
120089002A
Requesting a New Key Code for Customer with Lost or Stolen Keys
PIP-5074
CHEVROLET: THE A/C COMPRESSOR HOSE HAS AN OIL LEAK, FROM OIL FILTER, DUE TO THE RUBBING OF OIL FILTER AND TO INCREASE DISTANCE, FROM A/C HOSE AND FILTER, AN ALTERNATE OIL FILTER WILL BE INSTALLED. MODEL 2012-2013 CAPTIVA SPORT. *PE
SB-PIP-5074
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PI0086D
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ISSUES
PI0373A
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.
090730018C
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
PIC5588A
Programming And Activation Of Replacement OnStar Modules.
PIT5138A
Remote Keyless Entry Functions Are Inoperative When The Ignition Key Is Off.
PIT5159
GM: CLUSTER INOPERATIVE AND/OR GAUGES ERRATIC. THIS MAY BE CAUSED BY A POOR PIN CONNECTION AT THE CONNECTOR FOR THE CLUSTER. *JS
PIP-4624-M
CHEVROLET/BUICK/GMC: RESTRICTION, THROUGH THE PQC, HAS BEEN PLACED ON THE VALVE CONTROL SOLENOID (TEHCM) P/N 24256524 AND 24265367, TO ASSIST ENGINEERING FEEDBACK PRODUCT. *PE
PIT-5148
CHEVROLET: REAR POWER DOOR LOCKS MAY NOT UNLOCK PROPERLY WHEN USING KEY FOB OR POWER DOOR LOCK SWITCH. *PE
PI-0670
GMC/BUICK/CHEVROLET: TRANSMISSION SLIPS WHEN IN REVERSE OR NOT IN REVERSE, 3RD GEAR OR NO 3RD GEAR, FLARE SHIFTING TO 5TH OR NO 5TH GEAR. *PE UPDATED 4/17/12. *PE
SB-11275-B
GM: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. CARPETED FLOOR MATS MISSING. DEALERS ARE TO INSTALL CARPETED FLOOR MATS WHEN MATS BECOME AVAILABLE. *JS
SB-11275-A
BUICK/CADILLAC/CHEVROLET/GMC: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION REGARDING CERTAIN VEHICLES RECEIVED BY DEALERSHIP WITHOUT THE CARPETED FLOOR MATS. *PE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.