Vehicle report

2011 CHEVROLET CAPTIVA

Compare every CHEVROLET CAPTIVA yearNHTSA and EPA records

Service bulletins

412 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIP4902W

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT3271Q

Service Bulletin/Repair Instructions

This preliminary information communicates information about how to determine if a wheel and tires size change is available.

PIP4902V

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIP6104

Service Bulletin/Repair Instructions

This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.

PIP4902U

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIT5214G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

13598

Other

New Vehicle Monitoring Programs Section in IVH

PIP4902T

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

PIC5650M

Service Bulletin/Repair Instructions

PIP4902S

Service Bulletin/Repair Instructions

This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.

25-NA-156

Service Bulletin/Repair Instructions

This service bulletin provides information on Tire Sidewall Irregularities.

00-06-01-026R

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

13-02-32-001H

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

PIP5358D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

21-NA-043

Service Bulletin/Repair Instructions

This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5962B

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

04-06-01-029K

Service Bulletin/Repair Instructions

This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIP6015

Service Bulletin/Repair Instructions

This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.

10-00-89-009F

Service Bulletin/Repair Instructions

This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).

01-06-01-011Q

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

20-NA-132

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.

07-00-89-037T

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

04-06-04-051J

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

08-07-30-026I

Service Bulletin/Repair Instructions

This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

18-NA-146

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

PIC5650L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

24-NA-174

Service Bulletin/Repair Instructions

The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

05-03-08-002J

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

01-00-89-010S

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

07-06-01-016J

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

00-06-01-012N

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

05-06-04-022V

Service Bulletin/Repair Instructions

This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

16-NA-222

Service Bulletin/Repair Instructions

This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.

09-06-04-026Y

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

18-NA-306

Service Bulletin/Repair Instructions

This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).

PI0754G

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

16-NA-158

Service Bulletin/Repair Instructions

This service bulletin describes the U.S. Dealer Special Tool Loan Program process.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

99-04-20-002O

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

04-06-04-051I

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

18-NA-125

Service Bulletin/Repair Instructions

This service bulletin provides information for engine oil life monitor operation calculation.

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

20-NA-016

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

16-NA-119

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

06-00-89-029V

Service Bulletin/Repair Instructions

This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

10-08-110-001K

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

15-00-89-004G

Service Bulletin/Repair Instructions

This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

00-03-10-006P

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).

17-NA-052

Service Bulletin/Repair Instructions

This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

23-NA-103

Service Bulletin/Repair Instructions

This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).

07-00-89-037S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.

PIP5596A

Service Bulletin/Repair Instructions

This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

19-NA-044

Service Bulletin/Repair Instructions

This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

PI0281K

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

22-NA-240

Service Bulletin/Repair Instructions

This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.

PI0592I

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

PIT5074P

Service Bulletin/Repair Instructions

PIT5962A

Service Bulletin/Repair Instructions

This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.

PIT5214F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIT5099G

Service Bulletin/Repair Instructions

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

17-NA-281

Service Bulletin/Repair Instructions

This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the Pico Scope.

09-00-89-016H

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

15-00-89-004F

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010R

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

04-06-04-051H

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

09-06-04-026X

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

17-NA-066

Service Bulletin/Repair Instructions

This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.

PIP5358C

Service Bulletin/Repair Instructions

99-09-40-005I

Service Bulletin/Repair Instructions

This service bulletin provides information on availability for a seat belt extender.

PIP4902R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

99-08-51-001F

Service Bulletin/Repair Instructions

This service bulletin provides information on Paintless Dent Repair Process.

13-08-116-001I

Service Bulletin/Repair Instructions

PIT4261J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

04-07-30-013E

Service Bulletin/Repair Instructions

This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

08-07-30-026H

Service Bulletin/Repair Instructions

12-03-10-001E

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

PIC5650K

Service Bulletin/Repair Instructions

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

12-03-10-001D

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

10-08-110-001J

Service Bulletin/Repair Instructions

This service bulletin provides information on proper use of floor mats.

PI0281J

Service Bulletin/Repair Instructions

This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.

00-06-01-012M

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

00-06-01-026Q

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

07-06-01-016I

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-02-32-001G

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.

15-NA-017

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.

18-NA-263

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only).

PI0754F

Service Bulletin/Repair Instructions

This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.

99-04-20-002N

Service Bulletin/Repair Instructions

This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

00-00-90-002M

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

07-03-16-004E

Service Bulletin/Repair Instructions

This service bulletin provides information for tire pressure monitoring (TPM) system concerns.

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

09-00-89-008F

Service Bulletin/Repair Instructions

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIP5632G

Service Bulletin/Repair Instructions

PIP4902Q

Service Bulletin/Repair Instructions

PIT3271N

Service Bulletin/Repair Instructions

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

PI0592G

Service Bulletin/Repair Instructions

This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

05-06-04-022T

Service Bulletin/Repair Instructions

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

07-06-01-016H

Service Bulletin/Repair Instructions

This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.

13-08-116-001H

Service Bulletin/Repair Instructions

15-00-89-004E

Service Bulletin/Repair Instructions

This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.

01-00-89-010Q

Service Bulletin/Repair Instructions

This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

05-00-89-072F

Service Bulletin/Repair Instructions

This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.

09-06-04-026W

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

00-06-01-012L

Service Bulletin/Repair Instructions

This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

04-06-04-051G

Service Bulletin/Repair Instructions

This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.

00-06-01-026P

Service Bulletin/Repair Instructions

This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

PIT4261H

Service Bulletin/Repair Instructions

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099F

Service Bulletin/Repair Instructions

16-NA-109

Service Bulletin/Repair Instructions

This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.

PIP5358B

Service Bulletin/Repair Instructions

PIP5856

Service Bulletin/Repair Instructions

This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PIT3271M

Service Bulletin/Repair Instructions

PIT3271L

Service Bulletin/Repair Instructions

PIP4902P

Service Bulletin/Repair Instructions

PIP4723F

Service Bulletin/Repair Instructions

PIP5632F

Service Bulletin/Repair Instructions

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIC5650J

Service Bulletin/Repair Instructions

PIT4261G

Service Bulletin/Repair Instructions

PIP5632E

Service Bulletin/Repair Instructions

PIT3271K

Service Bulletin/Repair Instructions

060089029Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.

16NA383

Service Bulletin/Repair Instructions

This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

PIP4495F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a loud tick or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.

PIP3535C

Service Bulletin/Repair Instructions

This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.

PIP4495E

Service Bulletin/Repair Instructions

070849020M

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide

150089004B

Service Bulletin/Repair Instructions

Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

150089005A

Service Bulletin/Repair Instructions

Essential Tools that Include Consumable Parts (U.S. Only)

16-NA-249

Service Bulletin/Repair Instructions

LOW AUDIBLE WHINE NOISE FROM ENGINE

PIP3535B

Service Bulletin/Repair Instructions

17-NA-126

Service Bulletin/Repair Instructions

This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.

PIT5389C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIC4935F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

PIP4723B

Service Bulletin/Repair Instructions

GCUS-3-848

Service Bulletin/Repair Instructions

44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.

PIC3278G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4801H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIC5959C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIC5588C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

PIP5029H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

PIP5338A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

PIP4902J

Service Bulletin/Repair Instructions

08-03-10-006F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

PIC5759B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

PIT4733K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.

PIT5236J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.

PIC5492E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

GCUS-3-770

Service Bulletin/Repair Instructions

15806 Customer Satisfaction Program (Suspension lifted for 09-10 MY). Under certain conditions, a software error could cause the odometer value in certain vehicles to increase a small amount (a fraction of a [mile/kilometer]) at startup. The impact of this potential error on the vehicle is minor-only three occurrences in the field have been reported to GM out of a population of several hundred thousand vehicles. Reprogram the IPC software.

PIT3099N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIP5163B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT5389B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

GCUS-3-734

Service Bulletin/Repair Instructions

15806 - Customer Satisfaction Program (MY 09-10 Suspended) - Under certain conditions, a software error could cause the odometer value in certain vehicles to increase a small amount (a fraction of a [mile/kilometer]) at startup. The impact of this potential error on the vehicle is minor?only three occurrences in the field have been reported to GM out of a population of several hundred thousand vehicles. Dealers are to reprogram the IPC software.

GCUS-3-730

Service Bulletin/Repair Instructions

15806 - Customer Satisfaction Program - Under certain conditions, a software error could cause the odometer value in certain vehicles to increase a small amount (a fraction of a [mile/kilometer]) at startup. The impact of this potential error on the vehicle is minor?only three occurrences in the field have been reported to GM out of a population of several hundred thousand vehicles. Dealers are to reprogram the IPC software.

PIP5282A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR. THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.

PIP5029G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

16NA241

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.

PIT5074J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

PI1394A

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.

16NA260

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

PI0388F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.

PIP4786C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

030603004R

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.

16NA119

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.

16NA249

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.

070898001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.

000601012F

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.

030604017I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

110849001S

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.

000601026I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.

00-03-10-006M

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT.

GCUS-3-557

Service Bulletin/Repair Instructions

15806 - Customer Satisfaction Program. This message was to inform dealers that bulletin 15806 was not released as scheduled on Monday, May 16, 2016. This action was necessary due to an anomaly in the calibration testing that resulted in the instrument panel cluster odometer not operating as intended. The affected calibration has been temporarily disabled and will not be available until further testing has been completed. Unfortunately, the decision to hold the bulletin was made after the involved vehicles were updated in IVH. This resulted in 15806 being identified as ?open? in the required field actions section and was quickly reversed to remove the field action.

SB-02-07-30-029Z

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.

SB-16NA-131

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.

PIC-5374-D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

PIC5374D

Service Bulletin/Repair Instructions

PIT5485B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIP5168E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.

PIC4707E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.

PIC5088F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

SB-10-08-46-001C

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.

SB-15-06-03-001B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.

PIC-4935-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC-5050-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

PIC4935E

Service Bulletin/Repair Instructions

PIC5050A

Service Bulletin/Repair Instructions

PIT5389A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

SB-03-06-03-004Q

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.

SB-06-08-47-001L

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES

SB-07-06-01-016C

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT

SB-16-NA-119

Service Bulletin/Repair Instructions

THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.

PI-0754-B

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.

SB-16-NA-117

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.

PIT5485A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PI-0281-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.

PIC-5260-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIC5260A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

SB-03-07-29-004K

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.

SB-16-NA-109

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.

PIT5236G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

PIC6181

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

09-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory

PIC5953A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

16-NA-055

Service Bulletin/Repair Instructions

This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near

11-00-89-005I

Service Bulletin/Repair Instructions

This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)

PIT4720D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.

PIP5264

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the step to diagnose and repair vehicles that may have engine misfire and check engine light with any or all cylinder misfires only on deceleration. Technician will need to remove the accessory belts and drive or brake stall at signature RPM. If the concern is gone inspect for debris in the belt or pulleys causing a jump and false misfires. Also lift the engine to unload the engine mounts and test again. If concern is gone then inspect for a ground out concern with the mounts causing false misfires.

PIP5257

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.

13-02-32-001D

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.

PIC5614A

Service Bulletin/Repair Instructions

Changing Turn-By-Turn Voice Response To Metric Or English Units

130232001D

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PIP5257A

Service Bulletin/Repair Instructions

PIT5353A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT4943D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

06-00-89-031D

Service Bulletin/Repair Instructions

OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

15-NA-079

Service Bulletin/Repair Instructions

OnStar Voice Fallback Number Update

PIP5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

PIT5214B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

PIC3100E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PIC5953B

Service Bulletin/Repair Instructions

PIP5338

Service Bulletin/Repair Instructions

GCUS-9-1009

Service Bulletin/Repair Instructions

14582A - Special Coverage (2012 model year Buick Enclave, Lacrosse, Regal; Chevrolet Traverse, and GMC Acadia vehicles have been removed). On some various model year vehicles, the throttle-position sensor may cause the engine to run rough, cause the malfunction-indicator lamp and/or an engine reduced power message to illuminate, and reduce the engine?s power. Dealers are to replace the throttle body assembly and gasket for Bosch equipped vehicles, or to install the throttle position sensor kit for Hitachi equipped vehicles. The Hitachi throttle body assembly only needs to be replaced if the sensor kit does not correct the condition. The repairs will be made at no charge to the customer. For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 24, 2015, are covered by this special coverage and must be submitted using the labor operation codes provided with this bulletin. Claims with repair orders prior to September 24, 2015, must be submitted to the Service Contract provider.

PIP5191A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.

GCUS-9-939

Service Bulletin/Repair Instructions

14582 - Special Coverage. On some 2008 model year (MY) Saturn Outlook; 2008-2009 MY Buick Allure, Chevrolet Equinox, Chevrolet Uplander, Pontiac G8, Pontiac Montana SV6, Pontiac Torrent, and Saturn VUE; 2008-2010 MY Hummer H3 and Pontiac G6; 2008-2011 MY Cadillac CTS, Cadillac SRX, and Chevrolet Impala; 2008, 2011-2012 MY Chevrolet Captiva; 2008-2012 MY Buick Enclave, Buick Lacrosse, Chevrolet Colorado, Chevrolet Malibu, and GMC Canyon; 2009 MY Hummer H3T; 2009-2011 MY Buick Lucerne; 2009-2012 MY Chevrolet Traverse and GMC Acadia; and 2010-2012 MY Buick Regal vehicles, the throttle-position sensor may cause the engine to run rough, cause the malfunction-indicator lamp and/or an engine reduced power message to illuminate, and reduce the engine's power. Dealers are to replace the throttle body assembly and gasket for Bosch equipped vehicles, or to install the throttle position sensor kit for Hitachi equipped vehicles. The Hitachi throttle body assembly only needs to be replaced if the sensor kit does not correct the condition. The repairs will be made at no charge to the customer. For vehicles covered by Vehicle Service Contracts, all eligible claims with repair orders on or after September 24, 2015, are covered by this special coverage and must be submitted using the labor operation codes provided with this bulletin. Claims September 2015 Bulletin No.: 14582 with repair orders prior to September 24, 2015, must be submitted to the Service Contract provider.

10-08-110-001D

Service Bulletin/Repair Instructions

This informational bulletin provides information on the proper use of GM floor mats.

00-06-01-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

PIT5236F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

PIC5932A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

PIT5236E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

PIC5491G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIT5442

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.

PIP5301A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps on how to diagnose and repair vehicle that may have Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P219A. Technician should use published Service Information diagnostics for Diagnostic Trouble Code P219A. If the Global Diagnostic System 2 fuel injector balance test does not isolate a cause for this concern, perform the Fuel Injector Diagnosis (w/CH47976 and CH-47976-500) in Service Information and evaluate for a rich or lean fuel injector.

PI0780A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides repair information to correct a customer concern of slip or no reverse or 3rd gear, no forward, MIL illuminated, DTC P0776 set.

PIC6107

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

PIT5214A

Service Bulletin/Repair Instructions

PIP5301

Service Bulletin/Repair Instructions

PIT5384A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

PIT5236D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

09-00-89-002K

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.

PIT5399

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIC4310L

Service Bulletin/Repair Instructions

PIP5282

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.

12-06-01-003B

Service Bulletin/Repair Instructions

This informational bulletin provides information for repairing engine front cover oil leak, sealing surface preparation and applying RTV sealant.

02-07-30-029X

Service Bulletin/Repair Instructions

This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).

14882

Service Bulletin/Repair Instructions

14882 - SPECIAL COVERAGE. CERTAIN VEHICLES EQUIPPED WITH A 2.4L ENGINE (LAF, LEA OR LUK) THAT HAVE EXPERIENCED HIGH OIL CONSUMPTION MAY ALSO EXPERIENCE A FROZEN AND/OR PLUGGED PCV (POSITIVE CRANKCASE VENTILATION) SYSTEM DURING COLD WEATHER OPERATION. THIS CONDITION MAY INCREASE CRANKCASE PRESSURE LEADING TO A REAR CRANKSHAFT SEAL OIL LEAK. IF THE OIL LEAK IS IGNORED OR NOT NOTICED, AN ENGINE CLATTER NOISE MAY BE NOTICEABLE AND/OR THE ENGINE PRESSURE WARNING LIGHT MAY ILLUMINATE. IF THIS CONDITION IS NOT CORRECTED, CONTINUED DRIVING WITH ENGINE NOISE AND/OR THE ENGINE OIL PRESSURE LIGHT ILLUMINATED MAY DAMAGE THE ENGINE. DEALERS ARE TO PERFORM A CRANKCASE PRESSURE CHECK, AND IF REQUIRED, REMOVE THE INTAKE MANIFOLD AND CLEAR THE PCV ORIFICE.

PIT5264C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

PIT3271G

Service Bulletin/Repair Instructions

PIC3278F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4310K

Service Bulletin/Repair Instructions

PIT5236A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.

PIT5074H

Service Bulletin/Repair Instructions

J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.

PIT5236B

Service Bulletin/Repair Instructions

OnStar Module Does Not Support All B101D Symptom Codes.

PIC5492C

Service Bulletin/Repair Instructions

PIT5353

Service Bulletin/Repair Instructions

PIP5029F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

PIT5264B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

11-00-89-005H

Service Bulletin/Repair Instructions

This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.

990420002I

Service Bulletin/Repair Instructions

Information on Driveline Clunk Noise

PIT5099A

Service Bulletin/Repair Instructions

A/C Blows Warm Or Poor Performance.

14-00-90-001

Service Bulletin/Repair Instructions

This informational bulletin provides additional information on the fuel tank capacitys.

PIP5226

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT3099M

Service Bulletin/Repair Instructions

SB-13-02-32-001

Service Bulletin/Repair Instructions

BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE

PIC5959B

Service Bulletin/Repair Instructions

PIC4310J

Service Bulletin/Repair Instructions

PIC5759A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.

PIP5163A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIP4902H

Service Bulletin/Repair Instructions

Recalls

Service Bulletin/Repair Instructions

Vehicle Recalls

14003A

Service Bulletin/Repair Instructions

Service Update Starter Motor B+ cable attachment

PIC5687D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that loose connection between the vehicle and a Bluetooth phone. Technician will need to use a scan tool to check the "Firmware Over-the-Air" value. If the "Firmware Over-the-Air" value is up to date and customer's concern is still present contact General Motors Technical Assistance Center for further assistance.

130089004I

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

14003

Service Bulletin/Repair Instructions

Service Update Starter Motor B+ cable attachment

PIP5191

Service Bulletin/Repair Instructions

PIC5491F

Service Bulletin/Repair Instructions

PIT3099L

Service Bulletin/Repair Instructions

12-06-01-009-D

Service Bulletin/Repair Instructions

GM: SOME VEHICLES REQUIRE REPLACEMENTS FOR HIGH FEATURE V6 TIMING CHAIN KITS AND GUIDE REPLACEMENTS. ALSO INCLUDED CHEVROLET CAPTIVA. MODEL YEARS 2007-2013. *JS UPDATED 7/18/14. *PE

120601009E

Service Bulletin/Repair Instructions

Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019

1406130001

Service Bulletin/Repair Instructions

High Voltage Safety ? High Voltage Disabling

PIC5374C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a frequent "off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.

PIC5959A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

PIT5264

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

PIC4801F

Service Bulletin/Repair Instructions

PIT4864F

Service Bulletin/Repair Instructions

Information On Requests To Add OnStar Bluetooth Option.

PIC3011H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

PIC5491E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

PIP5184

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that when replacing the camshaft part number 12626660. Technician will need to ensure that the date code and the finish of the camshaft. If the cam is discolored or has chatter marks, have parts department send the cam back as (MR code7) new defective.

PIT4943C

Service Bulletin/Repair Instructions

PIP5180

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have hard start, extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.

PIC5453A

Service Bulletin/Repair Instructions

99-08-51-007F

Service Bulletin/Repair Instructions

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

PIC5959

Service Bulletin/Repair Instructions

PIC5953

Service Bulletin/Repair Instructions

PIP3140F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

PI0281D

Service Bulletin/Repair Instructions

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

PI0754A

Service Bulletin/Repair Instructions

Rear and Side Tempered Glass Spots.

PIP5029E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

130089004D

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

PI-0018-B

Service Bulletin/Repair Instructions

GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE

PIC5932

Service Bulletin/Repair Instructions

PIP5163

Service Bulletin/Repair Instructions

PIC5491D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

PIC5492B

Service Bulletin/Repair Instructions

PIT5236

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.

130089004C

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130089010

Service Bulletin/Repair Instructions

PAC Courtesy Transportation Assistance Program

PIC5491C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

PIT3099K

Service Bulletin/Repair Instructions

PIC5904

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

120601009D

Service Bulletin/Repair Instructions

Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019

130089008

Service Bulletin/Repair Instructions

GM Wiring Repair Strategy Information

130090001

Service Bulletin/Repair Instructions

Information for Engine Oils Used in 2014 Model Year Vehicles

130232001B

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

130232001A

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PIT5214

Service Bulletin/Repair Instructions

PIT4720C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

130089004B

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130232001

Service Bulletin/Repair Instructions

Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature Conditions

PIC4707D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have at times the XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.

130089003

Service Bulletin/Repair Instructions

Vehicle Software Enhancements

130089004

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

130089004A

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

PI0944

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PI0944A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

SB12-08-132-001A

Service Bulletin/Repair Instructions

GENERAL MOTORS: ON SOME TRUCKS AND PASSENGER VEHICLES, ACCESSORY POWER OUTLETS (APO) AND TRAILER LIGHTING ARE COMMON ACCESSED ELECTRICAL SYSTEMS THAT ARE AFFECTED BY DEVICES THAT ARE PLUGGED IN AND BECOME INOPERATIVE DUE TO AN OPEN FUSE AND NO PROBLEM WITH VEHICLE IDENTIFIED. MODELS YEARS 2010-2014 TRUCKS AND PASSENGER. NO MODELS. *PE

PIC5491B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

120601009B

Service Bulletin/Repair Instructions

Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019

120601009C

Service Bulletin/Repair Instructions

Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019

1308116001A

Service Bulletin/Repair Instructions

Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues

PI0412B

Service Bulletin/Repair Instructions

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

PIP3140E

Service Bulletin/Repair Instructions

PIP5094

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

120601009A

Service Bulletin/Repair Instructions

Accessory Power Outlet and Trailer Lighting Fuse Replacement Labor Operation N1720 Fuse Replacement

PI0412A

Service Bulletin/Repair Instructions

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

PI0724B

Service Bulletin/Repair Instructions

Harsh 2-3 Shift.

PIC5687C

Service Bulletin/Repair Instructions

PIC5492A

Service Bulletin/Repair Instructions

PIT3173C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

120601009

Service Bulletin/Repair Instructions

Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, P0008, P0009, P0016, P0017, P0018 and/or P0019

PIC4310H

Service Bulletin/Repair Instructions

PIC4801E

Service Bulletin/Repair Instructions

12-03-10-002

Service Bulletin/Repair Instructions

This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles

PIC5687B

Service Bulletin/Repair Instructions

PIT4907A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

10-08-64-002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

120089002A

Service Bulletin/Repair Instructions

Requesting a New Key Code for Customer with Lost or Stolen Keys

PIC4935D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

PIC5491A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

PIT3099J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

PI0086D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A LIST OF CORRECTIONS FOR MULTIPLE CONCERNS REGARDING UNEXPECTED LOSS OF RADIO AUDIO (RADIO GOES SILENT/NO SOUND) AND OTHER BLACKBERRY PHONE - BLUETOOTH ISSUES

PI0373A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE FOR RELEARNING THE POWER FOLDING MIRRIORS AND ROAD TESTIN TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.

PIC5759

Service Bulletin/Repair Instructions

090730018C

Service Bulletin/Repair Instructions

Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission

PIC5588A

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

SB-11275-B

Service Bulletin/Repair Instructions

GM: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. CARPETED FLOOR MATS MISSING. DEALERS ARE TO INSTALL CARPETED FLOOR MATS WHEN MATS BECOME AVAILABLE. *JS

SB-11275-A

Service Bulletin/Repair Instructions

BUICK/CADILLAC/CHEVROLET/GMC: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION REGARDING CERTAIN VEHICLES RECEIVED BY DEALERSHIP WITHOUT THE CARPETED FLOOR MATS. *PE

PI-0412

Service Bulletin/Repair Instructions

GENERAL MOTORS: DUE TO THE PARASITIC DRAIN/DISCHARGE ON 2011 VEHICLES AND TRUCKS, A NO CRANK/NO START AND DEAD BATTERY WOULD OCCUR. CADILLAC STS AND CHEVROLET VOLT NOT INCLUDED. *PE

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.