Vehicle report

2005 CHEVROLET CORVETTE

Service bulletins

608 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

PIP5601C

Service Bulletin/Repair Instructions

This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.

PIT5074R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.

PIP5358D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

PIC4588C

Service Bulletin/Repair Instructions

This PIC directs technicians into some common areas to inspect when dealing with a folding top that appears to be misaligned.

PIC4793C

Service Bulletin/Repair Instructions

This PIC provides a diagnostic check to help technicians test for a weak hydraulic cylinder on a power folding top.

PIT5074Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIP4723J

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

17-NA-087

Service Bulletin/Repair Instructions

This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or Right, Wanders, Follows Depressions in Road Surface, Tramlining.

PIT5099H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

02-00-89-002X

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

PIT3271P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

General Communication

Service Campaign

Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

01-06-01-011P

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

24-NA-141

Service Bulletin/Repair Instructions

GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

16-NA-383

Service Bulletin/Repair Instructions

This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

18-NA-099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

24-NA-098

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

08-07-30-035H

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

09-00-89-008G

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

13-08-116-001J

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

10-08-45-001H

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

22-NA-074

Service Bulletin/Repair Instructions

This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

16-NA-338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

02-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.

PI1394B

Service Bulletin/Repair Instructions

This PI bulletin advises the technician on the proper way to install the pistons in an engine.

PIP5601B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PIT5074P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

23-NA-219

Service Bulletin/Repair Instructions

This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.

03-00-91-001I

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

01-06-01-011O

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

17-NA-170

Service Bulletin/Repair Instructions

This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.

02-00-89-002W

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).

10-00-89-006J

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIC6378C

Service Bulletin/Repair Instructions

This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.

PIT5099G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

07-08-49-020R

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

23-NA-153

Service Bulletin/Repair Instructions

The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

18-NA-073

Service Bulletin/Repair Instructions

This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

PIP5628G

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIP5358C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

01-06-01-011N

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

13-08-116-001I

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

02-00-89-002V

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

19-NA-219

Service Bulletin/Repair Instructions

This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

PIP5628F

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

08-07-30-035G

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

22-NA-009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

17-NA-073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

01-08-42-001O

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

PIP5628E

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

02-00-89-002U

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

09-00-89-008F

Service Bulletin/Repair Instructions

This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

PIP5540J

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

21-NA-124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

PIT3271N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

20-NA-138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

22-NA-205

Service Bulletin/Repair Instructions

This service bulletin provides information on Module Harvesting.

10-00-89-006I

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIC5453D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

22-NA-195

Service Bulletin/Repair Instructions

This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.

06-00-89-031H

Service Bulletin/Repair Instructions

This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.

13-08-116-001H

Service Bulletin/Repair Instructions

The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.

01-06-01-011M

Service Bulletin/Repair Instructions

This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

22-NA-181

Service Bulletin/Repair Instructions

This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.

PIP5640A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

20-NA-065

Service Bulletin/Repair Instructions

This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

PIC5260F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5358B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

12-00-89-003B

Service Bulletin/Repair Instructions

This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).

18-NA-346

Service Bulletin/Repair Instructions

This service bulletin provides a procedure to correct a customer concern of Vehicle Will Not Start and/or Service Electronic Steering Column Lock System Message Displayed on Driver Information Center (DIC).

PIC5260E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

01-00-89-010P

Service Bulletin/Repair Instructions

This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.

PIT3271M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIC6378B

Service Bulletin/Repair Instructions

This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.

PIT3271L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP4723F

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

22NA009

Service Bulletin/Repair Instructions

This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.

000090002L

Service Bulletin/Repair Instructions

This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.

030091001H

Service Bulletin/Repair Instructions

This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

PIT3099U

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

010842001N

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.

080730035E

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

21NA124

Service Bulletin/Repair Instructions

This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

100089006H

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).

PIP5358A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

17NA087

Service Bulletin/Repair Instructions

This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or Right, Wanders, Follows Depressions in Road Surface, Tramlining.

16NA338

Service Bulletin/Repair Instructions

This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

020089002T

Service Bulletin/Repair Instructions

This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

18NA099

Service Bulletin/Repair Instructions

This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.

PIP5163E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260D

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIP5540G

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5725A

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

20NA138

Service Bulletin/Repair Instructions

This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

010601011L

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

090604026S

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIT5074N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT3271K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIC6378A

Service Bulletin/Repair Instructions

This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.

PIP5628C

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIP5226D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT5099E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIC5453C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

PIP5628B

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

070849020Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

19NA262

Service Bulletin/Repair Instructions

This technical bulletin provides repair information to correct a customer concern of Clock Shows Dashes and Cannot be Set After Battery Disconnect.

16NA383

Service Bulletin/Repair Instructions

This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

PIP5725

Service Bulletin/Repair Instructions

This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use.  Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement.  This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.

020089002S

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).

19NA219

Service Bulletin/Repair Instructions

This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.

DOR-C5P7J-03

Service Bulletin/Repair Instructions

This SKU is an EGR Valve. The customer communication requested return of unsold inventory to inspect the electrical leads in the motor. The leads may become worn leading to voltage spikes which can cause a fault and engine light to come one; voltage spikes may also cause performance issues from misfiring.

DOR-Q9L3Y-03

Service Bulletin/Repair Instructions

This SKU is an HVAC Air Door Actuator. The customer communication requested return of unsold inventory to inspect the housing. There may be a gap between the 2 halves of the housing causing the actuator to bind and a loss of HVAC air door control. Loss of HVAC air door control can lead to discomfort as it may be stuck in a single orientation.

PIT3099T

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

PIP4723D

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester  and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

050307009I

Service Bulletin/Repair Instructions

This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIP5540F

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIC6378

Service Bulletin/Repair Instructions

This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.

100089009D

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.

010842001M

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

080310006G

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

PIT3271J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIT5074M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

100089006G

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).

PIP5540E

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5601A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

010601011K

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

100089009C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

17NA073

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding the field action courtesy transportation policy.

150844001J

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

PIT3099S

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.

090604026R

Service Bulletin/Repair Instructions

This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PIT3099R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.  Technicians should refer to Service Information for information regarding most accessories.  Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

100845001G

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.

090604026Q

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.

PI0430C

Service Bulletin/Repair Instructions

This preliminary information bulletin provides a procedure for suspension connector diagnosis and replacement due to the magnetically controlled suspension electrical connector not seated.

060847001O

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIT5652E

Service Bulletin/Repair Instructions

This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time.   Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair.  The listed Cadillac, Pontiac, and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.

PIT5074L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

080730035D

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

PIT5652D

Service Bulletin/Repair Instructions

This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time.   Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair.  The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.

PIP5640

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

PIP5226C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIT5652C

Service Bulletin/Repair Instructions

This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time.   Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair.  The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.

PIC5260C

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5652B

Service Bulletin/Repair Instructions

This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.

040089053G

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

070849020P

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

100845001F

Service Bulletin/Repair Instructions

This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".

PIP5540D

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

PIP5628

Service Bulletin/Repair Instructions

This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

PIC5650F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

010842001L

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.

PIP5540B

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

060847001N

Service Bulletin/Repair Instructions

This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.

PIP4925B

Service Bulletin/Repair Instructions

This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.

PIT5353C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

18NA346

Service Bulletin/Repair Instructions

This bulletin provides procedure information for the customer on the electronic steering column module failing to send the correct signal to the BCM.

PIP5601

Service Bulletin/Repair Instructions

This Preliminary information communicates

PIP4138R

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIT5099D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIP5163D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC5260B

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

PIT5099C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

PIT5399A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIC3225J

Service Bulletin/Repair Instructions

The purpose of this Preliminary Information is to provide repair tips to the servicing technician when replacing components of the Remote Keyless Entry System.

080730035C

Service Bulletin/Repair Instructions

This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.

090604026N

Service Bulletin/Repair Instructions

This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada

PIC5367A

Service Bulletin/Repair Instructions

The purpose of this Preliminary Information is to aid the dealership technician in diagnosing an intermittent no crank concern.

030603004W

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

060601010D

Service Bulletin/Repair Instructions

This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.

PIP5067A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on and an engine misfire. Technician should inspect the torque tube coupling for damage.

PIP5226B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

PIP4138Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIT3271H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIP5540A

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

100864002D

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

PIP5540

Service Bulletin/Repair Instructions

This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

PIC5650D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

120089007A

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

010601011J

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIT4730B

Service Bulletin/Repair Instructions

This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line.

070604019F

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

PIC3100F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

PIC5650C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

PIT5353B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

070849020M

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide

150089004B

Service Bulletin/Repair Instructions

Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

150089005A

Service Bulletin/Repair Instructions

Essential Tools that Include Consumable Parts (U.S. Only)

030603004V

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

PIP4723C

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIT5074K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

PIT5389E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIT3099Q

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

PIP5163C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIC3139C

Service Bulletin/Repair Instructions

The purpose of this Preliminary Information is to let the customer/technician know that the vehicle listed must be placed into reverse before shutting the ignition off otherwise the battery will become discharged.

PIC5588D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

PIT3099P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

00-06-01-012G

Service Bulletin/Repair Instructions

This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.

03-06-03-004U

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

15-08-44-001I

Service Bulletin/Repair Instructions

This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.

15-08-73-001A

Service Bulletin/Repair Instructions

This informational bulletin explains how to update the older Onstar module software to new software over GSA.

06-08-47-001M

Service Bulletin/Repair Instructions

This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.

10-00-89-006F

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers how to submit a product information report.

PIT5389C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

07-07-30-010D

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.

PIC4935F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

PIP4723B

Service Bulletin/Repair Instructions

This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

PIC3278G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4801H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

PIC5588C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

02-00-89-002Q

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

PIP5029H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

PIP5338A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

GCUS-9-3515

Service Bulletin/Repair Instructions

15643A - Special Coverage. On some vehicles, equipped with power seats, the wire harness connector from the seat side airbag and buckle tensioner to the body has a design interference between the vertical adjust crossbar and the carpet.  When the seat is moved forward or back, the connector may be dragged along the carpet, pulling terminals loose or pulling the connector apart.  This will cause a diagnostic trouble code to be set and the service airbag light will be illuminated. Dealers will replace the affected harness connectors with accessory wiring harness components. The repairs will be made at no charge to the customer.

08-03-10-006F

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

03-08-46-004S

Service Bulletin/Repair Instructions

This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

07-08-49-020L

Service Bulletin/Repair Instructions

This informational bulletin provides information for the IPC odometer programming method quick reference guide.

PIP4138P

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

08-08-44-015H

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIC5492E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

02-00-89-002P

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.

05-00-89-055F

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.

PIT3099N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIP5163B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT5389B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

030603004S

Service Bulletin/Repair Instructions

This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.

030603004T

Service Bulletin/Repair Instructions

Battery Testing and Warranty Replacement Requirements (North America ONLY)

100844006D

Service Bulletin/Repair Instructions

This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.

05-08-44-024E

Service Bulletin/Repair Instructions

This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .

09-00-89-008C

Service Bulletin/Repair Instructions

This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.

09-00-89-016E

Service Bulletin/Repair Instructions

This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.

PIC5453B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. THE GENERAL MOTORS OF CANADA CUSTOMER CARE CENTRE IS THE SOLE AUTHORIZED PROVIDER OF A CERTIFICATION CONFIRMATION LETTER WHICH HELPS OUR CUSTOMERS IDENTIFY IF THEIR VEHICLES MEETS THE REQUIRED USA REGULATORY STANDARDS NECESSARY FOR IMPORTATION INTO THE USA.

08-08-44-015G

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

07-08-49-020K

Service Bulletin/Repair Instructions

This informational bulletin explains the programming method quick reference guide for the IPC Odometer.

PIC5491J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

PIP5029G

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

PIT5074J

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

PI1394A

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.

16NA260

Service Bulletin/Repair Instructions

THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

PIP4786C

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

030603004R

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.

000601012F

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.

030604017I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

PIC4299B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATES THE HARD-TO-FIND PAINT CODE FOR THE REAR HATCH AREA OF THE VEHICLE. THE TECHNICIAN IS TO USE PAINT CODE WA167A TO PAINT THESE AREAS.

000601026I

Service Bulletin/Repair Instructions

THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.

00-06-01-026H

Service Bulletin/Repair Instructions

This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.

PIP5094A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.

PIT5485B

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

15521

Service Bulletin/Repair Instructions

15521 ? Customer Advisory Letter. On these vehicles, if the side doors will not open from inside the vehicle due to low or no battery voltage, such as a discharged or disconnected battery, or if the vehicle is entered without the key fob or the fob is not working, customers are being advised that the driver and passenger side doors can still be opened from inside the vehicle by using the manual release levers located on the floor between the seats and the door openings. Also, if the vehicle's side doors will not open from outside the vehicle due to low or no battery voltage, such as a discharged or disconnected battery, or if the key fob is not working, customers are being advised that the driver side door can still be opened by using their key to manually open the vehicle's trunk and pulling the manual door release tab located in the trunk.

MC-15521

Service Bulletin/Repair Instructions

15521 – CUSTOMER ADVISORY LETTER. ON THESE VEHICLES, IF THE SIDE DOORS WILL NOT OPEN FROM INSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE, SUCH AS A DISCHARGED OR DISCONNECTED BATTERY, OR IF THE VEHICLE IS ENTERED WITHOUT THE KEY FOB OR THE FOB IS NOT WORKING, CUSTOMERS ARE BEING ADVISED THAT THE DRIVER AND PASSENGER SIDE DOORS CAN STILL BE OPENED FROM INSIDE THE VEHICLE BY USING THE MANUAL RELEASE LEVERS LOCATED ON THE FLOOR BETWEEN THE SEATS AND THE DOOR OPENINGS. ALSO, IF THE VEHICLE'S SIDE DOORS WILL NOT OPEN FROM OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE, SUCH AS A DISCHARGED OR DISCONNECTED BATTERY, OR IF THE KEY FOB IS NOT WORKING, CUSTOMERS ARE BEING ADVISED THAT THE DRIVER SIDE DOOR CAN STILL BE OPENED BY USING THEIR KEY TO MANUALLY OPEN THE VEHICLE'S TRUNK AND PULLING THE MANUAL DOOR RELEASE TAB LOCATED IN THE TRUNK.

15643

Service Bulletin/Repair Instructions

15643 ? Special Coverage. On these vehicles, the wire harness connector from the seat side airbag and buckle tensioner to the body has a design interference between the vertical adjust crossbar and the carpet. When the seat is moved forward or back, the connector may be dragged along the carpet, pulling terminals loose or pulling the connector apart. This will cause a diagnostic trouble code to be set and the service airbag light will be illuminated. Dealers are to replace the affected harness connection with a soldered connection.

PIC5088F

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

SB-15643

Service Bulletin/Repair Instructions

15643 – SPECIAL COVERAGE. ON THESE VEHICLES, THE WIRE HARNESS CONNECTOR FROM THE SEAT SIDE AIRBAG AND BUCKLE TENSIONER TO THE BODY HAS A DESIGN INTERFERENCE BETWEEN THE VERTICAL ADJUST CROSSBAR AND THE CARPET. WHEN THE SEAT IS MOVED FORWARD OR BACK, THE CONNECTOR MAY BE DRAGGED ALONG THE CARPET, PULLING TERMINALS LOOSE OR PULLING THE CONNECTOR APART. THIS WILL CAUSE A DIAGNOSTIC TROUBLE CODE TO BE SET AND THE SERVICE AIRBAG LIGHT WILL BE ILLUMINATED. DEALERS ARE TO REPLACE THE AFFECTED HARNESS CONNECTION WITH A SOLDERED CONNECTION.

PIC-4935-E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC-5050-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

PIC4935E

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

PIC5050A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

PIT5389A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

PIT5485A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

PIC-5260-A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

PIC5260A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

00-03-10-002J

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.

09-06-04-026L

Service Bulletin/Repair Instructions

This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2® or GDS 2 (U.S. and Canada)

PIC6181

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

08-07-30-026C

Service Bulletin/Repair Instructions

This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

PIP5232C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

03-06-03-004O

Service Bulletin/Repair Instructions

This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)

PIT5484A

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

PIC5953A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

02-08-42-001I

Service Bulletin/Repair Instructions

This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not

11-00-89-005I

Service Bulletin/Repair Instructions

This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)

PIP5226A

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

08-08-44-015F

Service Bulletin/Repair Instructions

This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)

01-08-42-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on exterior lamp condinsation and replacement guidelines

PIT4720D

Service Bulletin/Repair Instructions

THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.

16-NA-025

Service Bulletin/Repair Instructions

This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks

03-08-46-004R

Service Bulletin/Repair Instructions

This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)

06-06-01-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.

PIC6140B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

PIT5353A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIT5484

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

PIT5486

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIT4943D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

06-00-89-031D

Service Bulletin/Repair Instructions

OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification

07-08-49-020J

Service Bulletin/Repair Instructions

IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

15-NA-079

Service Bulletin/Repair Instructions

OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer – or any dealer near you – as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."

GCUS-3-368 (1552

Service Bulletin/Repair Instructions

15521 - CUSTOMER ADVISORY LETTER. THIS LETTER IS BEING SENT TO BRING TO THE CUSTOMER'S ATTENTION FEATURES THAT ARE COVERED IN THE VEHICLE'S OWNER MANUAL IN SITUATIONS WHERE THE CUSTOMER VEHICLE SIDE DOORS WILL NOT OPEN FROM INSIDE AND OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE. DEALERS ARE ALSO INSTRUCTED THAT IN CORRELATION WITH THIS CUSTOMER ADVISORY LETTER, A WEB-BASED TRAINING COURSE WILL BE REQUIRED FOR ALL CADILLAC AND CHEVROLET SALES CONSULTANTS, SALES MANAGERS, SERVICE CONSULTANTS, SERVICE MANAGERS, AND FIELD STAFF BEGINNING Q1 2016 VIA THE GM CENTER OF LEARNING.

PIP5232B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

PIC3100E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

15-08-44-001F

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

15-08-44-001G

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.

PIC6140A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

PIC3520C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about a failed module programming or difficulty performing certain diagnostic procedures due to the ignition not being in the "Ignition On, Engine Off" mode. Technician will need to press and hold the ACC/OFF portion of the Start/ACC/OFF mode button for 5 seconds with a valid keyless entry transmitter inside the vehicle and the transmission in Park or Neutral.

01-06-01-011I

Service Bulletin/Repair Instructions

This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.

PIC5953B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP5338

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

PIC6106B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the radio display that will go blank and come back on after a few seconds then display may show the splash screen or come back on to the last screen that was displayed. Technician should USB update the radio using Tis2Web and follow up with a Service Programming System program.

PIP4404F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.

05-03-07-009H

Service Bulletin/Repair Instructions

This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.

PIT5464

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

PIP5325

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

GCUS-9-832

Service Bulletin/Repair Instructions

14717 - Special Coverage. On some 2005-2013 model year Chevrolet Corvette vehicles equipped with a manual transmission (RPO MM6, MZ6, MH3 or ME2), the clutch system may fail if unapproved fluids are used to service the system or if a high-pressure pulse occurs during a clutch self-adjustment event. If the clutch system fails, the clutch pedal may not return if depressed. If the clutch pedal does not return, it may be possible to start the vehicle when the transmission is in any gear. This could result in unexpected vehicle movement when the engine is started.

SB-14717

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

15-00-89-005

Service Bulletin/Repair Instructions

This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).

00-06-01-026G

Service Bulletin/Repair Instructions

This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.

09-09-40-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

09-06-04-026K

Service Bulletin/Repair Instructions

This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).

03-06-03-004N

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).

07-06-04-019E

Service Bulletin/Repair Instructions

This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

02-00-89-002O

Service Bulletin/Repair Instructions

This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).

PIC6107

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

15-08-44-001C

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

PIC6101

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.

PIT5384A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

02-07-30-052J

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.

05-06-04-035E

Service Bulletin/Repair Instructions

This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.

15-08-44-001A

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-44-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

02-08-42-001H

Service Bulletin/Repair Instructions

This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

PIT5399

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

PIC4310L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PI0512B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides service personnel with characteristics of wide low aspect ratio tires for customer concerns that vehicle pulls left or right, wanders, follows depressions in road surface, tramlining.

05-08-46-006T

Service Bulletin/Repair Instructions

This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.

00-05-22-002O

Service Bulletin/Repair Instructions

This informational bulletin provides technicians with a brake lathe calibration procedure.

15-08-44-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.

15-08-73-001

Service Bulletin/Repair Instructions

This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.

PIT5264C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

05-00-89-055E

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.

06-08-47-001K

Service Bulletin/Repair Instructions

This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.

10-08-45-001E

Service Bulletin/Repair Instructions

This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.

00-03-10-002I

Service Bulletin/Repair Instructions

This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of chromed aluminum wheels, along with warranty information regarding these conditions.

PI1394

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.

PIT3271G

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

PIC3278F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

PIC4310K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

09-06-04-026J

Service Bulletin/Repair Instructions

This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).

03-00-91-001G

Service Bulletin/Repair Instructions

This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

030848006J

Service Bulletin/Repair Instructions

This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.

1008110001C

Service Bulletin/Repair Instructions

This information provides the proper way to install the floor mats .

13146

Service Bulletin/Repair Instructions

PSR-Low-Beam Headlamps Inoperative

PIT5074H

Service Bulletin/Repair Instructions

J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.

PIT5353

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

PIP5029F

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

PIT5264B

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

11-00-89-005H

Service Bulletin/Repair Instructions

This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.

PIT5099A

Service Bulletin/Repair Instructions

A/C Blows Warm Or Poor Performance.

06-08-43-003E

Service Bulletin/Repair Instructions

This informational bulletin explains how to care for wiper blades.

PIP5232A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

07-08-49-020I

Service Bulletin/Repair Instructions

This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.

PIT5264A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

PIC6036

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.

PIP5232

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

08-08-44-015E

Service Bulletin/Repair Instructions

This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs

PIP5226

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

10-08-110-001B

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to use floor mats.

10-08-44-006C

Service Bulletin/Repair Instructions

This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a feedback form to the GM navigation disc center website.

02-00-89-002N

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

10-00-89-006E

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

03-06-03-004M

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

PIT3099M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

PIC4310J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

00-06-01-012E

Service Bulletin/Repair Instructions

This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.

PIP5163A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

00-00-89-027H

Service Bulletin/Repair Instructions

This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.

02-00-89-002M

Service Bulletin/Repair Instructions

This informational bulletin provides additional information to the technicians and how to submit a field product report.

10-00-89-006D

Service Bulletin/Repair Instructions

This information bulletin provides the dealers on how to submit a product information report.

PIC5214D

Service Bulletin/Repair Instructions

Excessive Brake Dust On Wheels.

Recalls

Service Bulletin/Repair Instructions

Vehicle Recalls

050308002F

Service Bulletin/Repair Instructions

This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.

PIC5088E

Service Bulletin/Repair Instructions

This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.

05-00-89-029C

Service Bulletin/Repair Instructions

This preliminary bulletin provides a information to the dealer for the requirements need for equipment.

PIC5214C

Service Bulletin/Repair Instructions

Excessive Brake Dust On Wheels.

PIC5588B

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

09-03-10-013B

Service Bulletin/Repair Instructions

This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.

03-06-03-004L

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not.

05-08-46-006S

Service Bulletin/Repair Instructions

This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.

SB-0000191927-A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

05-06-04-035D

Service Bulletin/Repair Instructions

This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.

130089004I

Service Bulletin/Repair Instructions

Car and Truck Fix it Right the First Time Issues

01-08-42-001J

Service Bulletin/Repair Instructions

This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.

02-08-42-001G

Service Bulletin/Repair Instructions

This informational bulletin is to assist with the identification of issues that are not considered warrantable.

PIT3099L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

05-05-23-007B

Service Bulletin/Repair Instructions

This information bulletin explains that some surface cracking is OK and doesn?t require replacing.

SB-0505-23-007-B

Service Bulletin/Repair Instructions

CADILLAC/CHEVROLET: INFORMATION PROVIDED REGARDING THE POSSIBILITY OF BRAKE ROTOR SURFACE CRACKING THAT IS VISIBLE DUE TO THERMAL FATIGUE TESTING. MODEL 2005-09 SLUR, 2005-13 CORVETTE. *PE

03-06-03-004K

Service Bulletin/Repair Instructions

This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if it is warranty or not

PIT5264

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

PIT4864F

Service Bulletin/Repair Instructions

Information On Requests To Add OnStar Bluetooth Option.

PIC3011H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

10-08-64-002C

Service Bulletin/Repair Instructions

This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.

08-03-10-006E

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow tire leak and low tire psi message on.

PIT4943C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

PIC5453A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

PIC5961

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a "NO FOB DETECTED" message when attempting to start the vehicle. Technician will need to ensure the battery is adequately charged to start vehicle. Also check the battery in the FOB to ensure it is 2 to 3 direct current volts. Technician will need to get in the vehicle with a known good fob press the Start Button. Listen for a click noise or a series of click noises from the Remote Control Door Lock Receiver. If there is only one click instead of a series of clicks, then the transistor internal to the Remote Control Door Lock Receiver is not operating properly. For this condition, replace the Remote Control Door Lock Receiver module.

99-08-51-007F

Service Bulletin/Repair Instructions

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

04-00-89-053F

Service Bulletin/Repair Instructions

This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.

PIC5953

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

PIP3140F

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

01-07-30-042H

Service Bulletin/Repair Instructions

This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.

08-08-44-029D

Service Bulletin/Repair Instructions

This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.

PIP5169

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.

PI0281D

Service Bulletin/Repair Instructions

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

10-00-89-006C

Service Bulletin/Repair Instructions

This informational bulletin provides directions on submitting different PIRs

08-08-44-015D

Service Bulletin/Repair Instructions

This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM warranty or not.

05-00-89-072C

Service Bulletin/Repair Instructions

This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.

SB-0000178781-A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

10-08-110-001A

Service Bulletin/Repair Instructions

This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.

PIP5163

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

PIT3099K

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

130089009

Service Bulletin/Repair Instructions

Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules

06-00-89-026L

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.

PIC5904

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

06-06-01-010B

Service Bulletin/Repair Instructions

This informational bulletin provides information on close-coupled converter and engine replacement.

PIP4404E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.

00-03-10-003R

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.

PIP4138N

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

08-08-67-013H

Service Bulletin/Repair Instructions

This technical bulletin provides a procedure for replacing the front roof lift off handle to eliminate a snap, pop, or rattle type noise.

03-06-03-004I

Service Bulletin/Repair Instructions

This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8 battery tester/charger.

10-00-89-010C

Service Bulletin/Repair Instructions

This informational bulletin provides information on key codes security rules and information on GM key code look up application.

10-00-89-009B

Service Bulletin/Repair Instructions

This informational bulletin provides information on key code security and information on GM key code look up applications.

PIC4299A

Service Bulletin/Repair Instructions

This Preliminary information communicates the hard-to-find paint code for the rear hatch area of the vehicle. The technician is to use paint code WA167A to paint these areas.

05-09-40-002G

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.

07-08-49-020H

Service Bulletin/Repair Instructions

This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.

00-05-22-002N

Service Bulletin/Repair Instructions

This informational bulletin provides information for Disc Brake Warranty Service and Procedures.

02-07-30-052I

Service Bulletin/Repair Instructions

This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.

08-06-01-006D

Service Bulletin/Repair Instructions

This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.

11-00-89-005E

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.

02-08-98-002D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.

08-08-110-001G

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 08-08-110-001F to add the 2013 model year and update Condition, Cause and Correction #1 information.

09-00-89-008A

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.

07-03-10-015C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab Warranty Information.

05-08-48-001C

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.

PI0430B

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a revision of PI0430A to update the model years.

05-03-07-009F

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor Operations.

13-00-89-004B

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 13-00-89-004A to include updated information.

06-00-89-026K

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor operations.

09-07-30-018D

Service Bulletin/Repair Instructions

This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor Operation.

09-00-89-016C

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.

PIT4720C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

03-06-03-004H

Service Bulletin/Repair Instructions

This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.

13-00-89-005

Service Bulletin/Repair Instructions

This technical bulletin provides Warranty Administration - New Labor Codes information.

13-00-89-004A

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference information/bulletin PI0746C.

99-04-20-002H

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.

13-00-89-004

Service Bulletin/Repair Instructions

This technical bulletin provides a revision of 10-00-89-017Z to include updated information.

11-00-89-005D

Service Bulletin/Repair Instructions

This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.

10-00-89-017Z

Service Bulletin/Repair Instructions

This informational bulletin provides information on fix it right for first time issues.

00-03-10-002G

Service Bulletin/Repair Instructions

This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.

PIP3140E

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

PIP5094

Service Bulletin/Repair Instructions

This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

13-08-51-001

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

08-08-51-002A

Service Bulletin/Repair Instructions

This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.

03-00-89-013H

Service Bulletin/Repair Instructions

This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S. and Canada Only)

PIP4138M

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

PIP4138L

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

11-00-89-005C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm

PIC3718E

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

PIT3173C

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

10-00-89-017X

Service Bulletin/Repair Instructions

This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.

PIC-5335-A

Service Bulletin/Repair Instructions

CADILLAC/CHEVROLET: FOR NO APPARENT REASON, THE FRONT AND/OR REAR, COMPOSITE SPRINGS WOULD CRACK AND/OR BECOME BROKEN. MODELS 2004-2009 XLR; 1997-2013 CORVETTE. *PE

PIC5335A

Service Bulletin/Repair Instructions

Composite Transverse Spring Damage.

PIC5394A

Service Bulletin/Repair Instructions

Navigation System - Agree - Button Displays Randomly At Start.

080846004A

Service Bulletin/Repair Instructions

This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.

000089027G

Service Bulletin/Repair Instructions

This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.

PIC4310H

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

PIC3379D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have multiple Head Up Display issues. An issue with the Head Up Display image may not appear clear can be caused by a non-original equipment manufacturer windshield installed. Another issue that may be present with the Head Up Display is the segments illuminate intermittently this can be caused by the ambient lighting conditions. A poor or hazy Head Up Display image can be caused by Instrument Panel emit fumes that cause a film to form on the HUD lens. Technician will need to use Isopropyl Rubbing Alcohol to clean the lens.

12-03-10-002

Service Bulletin/Repair Instructions

This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles

060089026J

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

100089010B

Service Bulletin/Repair Instructions

This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.

010089010J

Service Bulletin/Repair Instructions

This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

100089017W

Service Bulletin/Repair Instructions

This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.

PIT4907A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

10-08-64-002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

100864002B

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork

PIC4935D

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

PIC5049A

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that after filling the vehicle, the fuel gauge only reads half tank or a difficult time filling the fuel tank. Technician should inspect the inspect the Evaporative Emissions System vent hose for a kink.

PIT3099J

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

09-07-30-018C

Service Bulletin/Repair Instructions

This warranty administration bulletin provides information on the change in automatic transmission add conditions documentation and claim submissions

12-00-89-007

Service Bulletin/Repair Instructions

This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.

PI0373A

Service Bulletin/Repair Instructions

This preliminary informational bulletin provides a procedure for relearning the power folding mirriors and road testin to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.

PIP5067

Service Bulletin/Repair Instructions

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on and an engine misfire. Technician should inspect the torque tube coupling for damage.

11-00-89-005B

Service Bulletin/Repair Instructions

This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm

10-00-89-017V

Service Bulletin/Repair Instructions

This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.

PIC-5049

Service Bulletin/Repair Instructions

CHEVROLET/CADILLAC: FUEL TANK HARD TO FILL OR DISPLAYS 1/2 TANK AFTER FILLING. *PE MODELS 2004-2009 XLR; 2005-2013 CORVETTE. UPDATED 12/5/12. *PE

PIC5588A

Service Bulletin/Repair Instructions

Programming And Activation Of Replacement OnStar Modules.

SB-07-07-31-001E

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIC4234C

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

PIT-3749D

Service Bulletin/Repair Instructions

GM: ON SOME TRUCK MODELS THERE IS SOME FRAME CORROSION. *RM UPDATED ON 5/2/2012. *KB

09-09-40-001A

Service Bulletin/Repair Instructions

GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE

05-09-40-002E

Service Bulletin/Repair Instructions

GM: SERVICE BULLETIN EXPLAINING WHEN THE SAFETY BELTS ARE SUPPOSED TO LOCK. *RM UPDATED 12/6/11. *PE

PIP-4492P

Service Bulletin/Repair Instructions

BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE

PB-10037A

Service Bulletin/Repair Instructions

GM: ONSTAR IS MAKING INCOMPLETE CALLS WITHOUT THE DRIVER KNOWING. WHEN HAVE A DATA CONNECTION. *RM

10-00-89-017C

Service Bulletin/Repair Instructions

GM: INFORMATION ON FIXING MULTIPLE SITUATIONS RIGHT THE FIRST TIME. *RM

PIP-4138K

Service Bulletin/Repair Instructions

GM: THE SERVICE ENGINE SOON LIGHT IS ON, THERE IS ALSO A MISFIRE OR ENGINE NOISE. THERE ARE MULTIPLE POSSIBLE CAUSES. *RM

PIC-5347A

Service Bulletin/Repair Instructions

GM: THE FUEL GAUGE MAY SHOW EMPTY WHEN THERE IS STILL GAS IN THE TANK. VEHICLES MAY ALSO RUN OUT OF GAS WITH THE FUEL GAUGE AT HALF-FULL. *RM

PIC-5368

Service Bulletin/Repair Instructions

CHEVROLET: ABS/TCS LIGHT ON AND DTCS C1225/C0035 AND/OR C1226/C0040 DUE TO AFTERMARKET BRAIDED STAINLESS STEEL BRAKE LINES. *PE

3144

Service Bulletin/Repair Instructions

SLIGHT PULL LEFT OR RIGHT, TIRE WANDER. *TC UPDATED 6/4/10. *PE

08089-B

Service Bulletin/Repair Instructions

GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE

3559

Service Bulletin/Repair Instructions

REAR AXLE CHATTER SHUDDER ON TURNS. *SC UPDATED. *KB UPDATED 9/30/08. *PE

08-089B

Service Bulletin/Repair Instructions

BUICK CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. CSC LETTER WAS RECEIVED. *PE

07-301

Service Bulletin/Repair Instructions

CHEVROLET PONTIAC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-FUEL TANK FILLER CAP. A CONDITION WHERE THE FUEL TANK FILLER CAP WON'T TIGHTEN PROPERLY, OR THE FUEL TANK FILLER CAP WON'T COME OFF, OR IS BROKEN. CSC LETTER WAS RECEIVED. *PE

07301

Service Bulletin/Repair Instructions

CHEVROLET PONTIAC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. VEHICLES EQUIPPED WITH A 6.0L V8 ENGINE, MAY EXPERIENCE A CONDITION WHERE THE FUEL TANK FILLER CAP WON'T TIGHTEN PROPERLY OR CAP WON'T COME OFF, OR IS BROKEN. CSC LETTER. *PE

08-089

Service Bulletin/Repair Instructions

BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE

070420002

Service Bulletin/Repair Instructions

REAR AXLE CLUNK AND/OR CHATTER TYPE NOISE ON TURNS (DRAIN/REFILL REAR DIFFERENTIAL FLUID). *KB UPDATED 4/11/08. *NJ

4269

Service Bulletin/Repair Instructions

CLUTCH PEDAL STICKS TO THE FLOOR AND WILL NOT RETURN - ON A MANUAL TRANSMISSION. *NJ UPDATED 2/27/08. *NJ

4426

Service Bulletin/Repair Instructions

CENTER HIGH MOUNT STOP LAMP ILLUMINATES DIM ALL THE TIME. *NJ

4678

Service Bulletin/Repair Instructions

POP OR CREAK NOISE FROM REAR OF VEHICLE BEHIND THE SEATS. *NJ

4702

Service Bulletin/Repair Instructions

FOG LAMPS INOPERATIVE WITH APPROACH LIGHTS ON. *NJ

060235002

Service Bulletin/Repair Instructions

DIAGNOSTIC TROUBLE CODE (DTC) C0710 STEERING WHEEL POSITION SENSOR (SWPS) SIGNAL, SERVICE STABILITY SYSTEM MESSAGE ON DRIVER INFORMATION CENTER (DIC). *TT UPDATED 2/15/08. *NJ

070495001

Service Bulletin/Repair Instructions

TAPPING OR SCRAPING NOISE FROM REAR WHEEL AREA (REPLACE WHEEL DRIVE SHAFT NUT). *NJ

4624

Service Bulletin/Repair Instructions

FINE CRACKS OR CRAZING ON HEAD LAMP LENS. *NJ

030730007

Service Bulletin/Repair Instructions

DELAYED ENGAGEMENT WHEN SHIFTING INTO THESE POSITIONS. PARK INTO REVERSE, NUETRAL INTO DRIVE, NUETRAL INTO REVERSE, AND PARK INTO DRIVE. THIS BULLETIN INCLUDES ALL 2000 - 2007 GM LIGHT DUTY TRUCKS. *KB

4288

Service Bulletin/Repair Instructions

WATER LEAK PASSENGER FLOOR OR ELECTRICAL CENTER. *KB

4188

Service Bulletin/Repair Instructions

BATTERY DRAIN CHECK LIST. CHEVROLET. *KB

050310015

Service Bulletin/Repair Instructions

TIRE ROTATION ON VEHICLES WITH DIFFERENT FRONT AND REAR TIRE/WHEEL SIZES. *TT

05112

Service Bulletin/Repair Instructions

PAINTED ROOF ADHESIVE SEPARATION. *TT

060867006

Service Bulletin/Repair Instructions

INFORMATION ON ADDING FOAM TO REPLACEMENT (SERVICE) ROOFS. *KB

050601001

Service Bulletin/Repair Instructions

CHECK GAGES LIGHT BATTERY VOLTAGE, LOW ACCESSORY DRIVE BELT SLIPPING OR MISSING. *EH

050310019

Service Bulletin/Repair Instructions

INFORMATION ON RUN FLAT, ZERO PRESSURE OR EXTENDED MOBILITY TIRES (EMT) AND UNIQUE SERVICING TECHNIQUES. *TT

050495001

Service Bulletin/Repair Instructions

REAR WHEEL DRIVE SHAFT NUT TORQUE SPECIFICATION REQUIREMENTS AND INFORMATION ON REPLACEMENT SHAFTS FOR SERVICE. *AK

050849027

Service Bulletin/Repair Instructions

ERRATIC FUEL GAUGE READINGS, FUEL GAUGE READS EMPTY WHEN THERE IS FUEL IN TANK, DTC P0463 OR P2068 SET, LOW FUEL MESSAGE DISPLAYED IN DIC. *TT

050842015

Service Bulletin/Repair Instructions

HEADLAMP BALLAST PART CHANGE. *TT

050859003

Service Bulletin/Repair Instructions

CREAK OR POPPING NOISE FROM ROOF NEAR WINDSHIELD/A PILLAR. *TT

709

Service Bulletin/Repair Instructions

OIL LIFE SYSTEM RESET PROCEDURES - CARS. GM TECH LINK. *TT

020730024A

Service Bulletin/Repair Instructions

DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT

030730007A

Service Bulletin/Repair Instructions

ENGAGEMENT TIME OF ELECTRONICALLY CONTROLLED TRANSMISSIONS IN GENERAL MOTORS VEHICLES. VARIOUS MODELS INCLUDING 2000-2006 ALL LIGHT DUTY TRUCKS. *TT

050523007

Service Bulletin/Repair Instructions

INFORMATION ON VISUAL BRAKE ROTOR SURFACE CRACKING. *SC

050603005

Service Bulletin/Repair Instructions

REVISED BATTERY NEGATIVE CABLE DISCONNECT/CONNECT PROCEDURE. *TT

050731001

Service Bulletin/Repair Instructions

CLUTCH PEDAL DOES NOT RETURN TO UP POSITION DURING SHIFTS AT HIGH ENGINE RPMS. *TT

050940003

Service Bulletin/Repair Instructions

PASSENGER SEAT BELT BUCKLE HARD TO MOVE PAST STITCHING AND/OR FINISH KNOT IS FRAYING. *TT

050604041

Service Bulletin/Repair Instructions

ERRATIC FUEL GAUGE READINGS, FUEL GAUGE READS EMPTY WHEN THERE IS FUEL IN TANK, DIAGNOSTIC TROUBLE CODE P0463 SET, SERVICE FUEL SYSTEM MESSAGE DISPLAYED. *TT

050842007

Service Bulletin/Repair Instructions

HEADLAMP ASSEMBLY SEAL TORN OR CUT. *TT

050308004

Service Bulletin/Repair Instructions

REVISED FRONT AND REAR UPPER AND LOWER BALL JOINT STUD NUT TIGHTENING SPECIFICATIONS. *TT

050310004

Service Bulletin/Repair Instructions

TIRE PRESSURE MONITORING (TPM) SYSTEM - TIRE MOUNTING AND DISMOUNTING. *TT

050842004

Service Bulletin/Repair Instructions

INFORMATION ON APPARENT HAZE/SHADOW APPEARANCE OF HEADLAMP ASSEMBLY. *TT

040601025

Service Bulletin/Repair Instructions

EXCHANGE PROGRAM FOR 2005 MODEL YEAR ENGINES. *TT UPDATE. *TT

040844023

Service Bulletin/Repair Instructions

VARIOUS RADIO/CD PLAYER CONCERNS. *TT

0508110001

Service Bulletin/Repair Instructions

AVAILABILITY OF FLOOR MAT/REAR COMPARTMENT DIVIDER RETAINERS. *TT

050866002

Service Bulletin/Repair Instructions

INFORMATION ON THE OPERATION OF THE REAR COMPARTMENT LID/HATCH/TRUNK EXTERIOR RELEASE SWITCH. *TT

050868001

Service Bulletin/Repair Instructions

MALFUNCTION INDICATOR LAMP (MIL), DIAGNOSTIC TROUBLE CODE (DTC) P0833, CRUISE CONTROL INOPERATIVE. *TT

702

Service Bulletin/Repair Instructions

CLOCK SETTING REVISION. *TT

030844005B

Service Bulletin/Repair Instructions

POOR RADIO RECEPTION OR RADIO STATIC/ INCREASED INTERFERENCE WITH REAR WINDOW DEFOGGER ON OR SOME REAR WINDOW DEFOGGER GRIDS MAY BE INOPERATIVE. *TT

04086

Service Bulletin/Repair Instructions

REAR BRAKE LINE ROUTING. PRODUCT SAFETY RECALL. *TT

701

Service Bulletin/Repair Instructions

FUEL FILTER REPLACEMENT. GM TECH LINK. *TT

040729003A

Service Bulletin/Repair Instructions

MISMACHINED TRANSMISSION COUNTERSHAFT SNAP RING GROOVE. *TT UPDATED *EH

040850018

Service Bulletin/Repair Instructions

DRIVER OR PASSENGER SEAT FUNCTIONS INOPERATIVE, BLOWN SEAT FUNCTION FUSE. *TT

612

Service Bulletin/Repair Instructions

CLOCK READS IN 24 HOUR TIME (MILITARY TIME) ON VEHICLES EQUIPPED WITH THE RPO US8 OR US9 RADIOS. GM TECH LINK. *TT

3242

Service Bulletin/Repair Instructions

OIL LEAK AT OIL COOLER LINES. *EH

611

Service Bulletin/Repair Instructions

LOW COOLANT SYSTEM OPERATION. *SC

030851001

Service Bulletin/Repair Instructions

TRANSSEAL TEMPORARY PROTECTIVE COATING REMOVAL INSTRUCTIONS. *TT BULLETIN 03-08-51-001, DATED 09/01/2003 REPLACED. *TT

009072004

Service Bulletin/Repair Instructions

TRANSMISSION SHIFT INTO REVERSE PRIOR TO SHUTTING OFF THE VEHICLE. *EH

040089041

Service Bulletin/Repair Instructions

PRE-DELIVERY AND SERVICE GUIDE. *TT

609

Service Bulletin/Repair Instructions

HVAC MODULE SERVICE. *SC

3126

Service Bulletin/Repair Instructions

MA5 5 SPEED NORMAL REVERSE GEAR OPERATION. *TC UPDATE. *TT

08182004

Service Bulletin/Repair Instructions

ACTION CENTER TO IDENTIFY AND RESOLVE ANY NEW PRODUCT CONCERNS. *TT

0804

Service Bulletin/Repair Instructions

OIL LIFE SYSTEM RESET PROCEDURES - CARS. *NM

07062004

Service Bulletin/Repair Instructions

CORVETTE NEW PRODUCT VIDEO. *EH

3079

Service Bulletin/Repair Instructions

STARTS WITHOUT BRAKE INPUT AND HARD TO SHIFT OUT PARK DIAGNOSTIC TROUBLE CODE 0161. *SC

3109

Service Bulletin/Repair Instructions

LOW RESONANCE VIBRATION AT IDLE WHEN TURNING. *SC

3139

Service Bulletin/Repair Instructions

LOW OR DEAD BATTERY. *TC

3141

Service Bulletin/Repair Instructions

RADIO PROGRAMMING WITH BASE RADIO (US8). *TC

3146

Service Bulletin/Repair Instructions

ABS BRAKE EBCM PROGRAMMING. *TC

3155

Service Bulletin/Repair Instructions

ERRATIC OR INOPERATIVE OIL PRESSURE GAUGE. *TT

3060

Service Bulletin/Repair Instructions

THE ENGINE DOES NOT STALL WHEN PERFORMING A P1870 DIAGNOSTIC TEST WITH THE TECH 2 SCAN TOOL OR WHEN COMMANDING THE TORQUE CONVERTER CLUTCH ENABLE SOLENOID ON APPLICATIONS THAT DO NOT HAVE THE P1870 DIAGNOSTIC TEST LISTED. 4L60E OR 4L65E TRANSMISSIONS. *TT

3089

Service Bulletin/Repair Instructions

SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT

3104A

Service Bulletin/Repair Instructions

6-SPEED SHIFTER RATTLE GROWL BUZZ NOISE. *SC

3132

Service Bulletin/Repair Instructions

LOWER REAR SHOCK ATTACHING BOLT MAY BREAK AFTER TORQUED. *TT

3134

Service Bulletin/Repair Instructions

NO CRANK AND DIC DISPLAYS NO FOB DETECTED. *TC UPDATE. *TT

3136

Service Bulletin/Repair Instructions

SLIP CONDITION IN 2ND, 3RD, OR 4TH. DAMAGED 2-4 OR 3-4 CLUTCH. *KB UPDATED 10/31/07. *NJ

3170E

Service Bulletin/Repair Instructions

IPC, INTERIOR LIGHTS AND/OR HEADLAMPS FLICKER. *AK FB2

3173

Service Bulletin/Repair Instructions

WATER LEAK ON DRIVERS FLOOR. *EH

3199

Service Bulletin/Repair Instructions

INFORMATION ON LOW COOLANT MESSAGE. *TT

3219

Service Bulletin/Repair Instructions

UNABLE TO PROGRAM TRANSMISSION CONTROL MODULE AFTER REPLACEMENT. *EH

3225

Service Bulletin/Repair Instructions

PROGRAMMING PROCEDURE FOR THE REMOTE CONTROL DOOR LOCK RECEIVER. *EH

3235

Service Bulletin/Repair Instructions

ENGINEERING INVESTIGATION ON THE NEW TRANSMISSION CONTROL MODULE. *EH

3293

Service Bulletin/Repair Instructions

MULTIPLE ELECTRICAL CONCERNS AND INSTRUMENT PANEL CLUSTER (IPC) GAUGES INOPERATIVE. *TT

3294

Service Bulletin/Repair Instructions

UNABLE TO PROGRAM A SPS MODULE. *TT

3319

Service Bulletin/Repair Instructions

A SIR LAMP AFTER DEPRESSING THE HORN FOR MORE THAN 5 SECONDS OR USING THE HORN TWO OR THREE TIMES IN SUCCESSION. A CURRENT OR HISTORY CODE B0104 OR B0101 MAY BE SET IN THE SDM. *TT

3320

Service Bulletin/Repair Instructions

4L65E (RPO M32) TRANSMISSION ACCUMULATOR SPRING USAGE. *TT

3335A

Service Bulletin/Repair Instructions

INVESTIGATION OF PUMP AREA LEAKS. *TT

3336

Service Bulletin/Repair Instructions

INDEXING DOOR GLASS THAT APPEARS TO BE STUCK OR INOPERATIVE. *SC

3359

Service Bulletin/Repair Instructions

LOWER REAR SHOCK ATTACHING BOLT MAY BREAK AFTER TORQUED. *TT

3363

Service Bulletin/Repair Instructions

4L60E/4L65E NO REVERSE. *TT

3369

Service Bulletin/Repair Instructions

TO BETTER UNDERSTAND SPRAG DAMAGE AN ENGINEERING INVESTIGATION IS BEING CONDUCTED. TYPICAL SYMPTOMS INCLUDE NO FORWARD MOVEMENT IN D4 OR D3 SHIFT LEVER POSITION. MOVEMENT CAN BE OBTAINED IN D2, D1 OR REVERSE. *TT

3384A

Service Bulletin/Repair Instructions

CRUISE CONTROL, FOG LAMPS, ACTIVE HANDLING, RKE PANIC MODE INOPERATIVE. *TT

3391

Service Bulletin/Repair Instructions

4L60E/4L65E AUTOMATIC TRANSMISSION MAY EXPERIENCE A CONDITION OF DISTRESSED TRANSMISSION FLUID AND/OR SLIPPING, LATE OR MISSED SHIFTS IN 2ND, 3RD, AND 4TH. *TT

3397

Service Bulletin/Repair Instructions

TELESCOPING STEERING WHEEL INOPERATIVE. *TT

3430

Service Bulletin/Repair Instructions

ANTI-LOCK BRAKING SYSTEM (ABS) LAMP ON WITH A DIAGNOSTIC TROUBLE CODE (DTC) C0820 SET IN THE ELECTRONIC BRAKE CONTROL MODULE (EBCM). *TT

3439

Service Bulletin/Repair Instructions

NO DRIVE IN D4 OR D3. TO INCLUDE 2005 GMC JIMMY. *TT

3440

Service Bulletin/Repair Instructions

SEAT BELTS LOCK INTERMITTENTLY. *TT

3441

Service Bulletin/Repair Instructions

FLOOR MAT REAR COMPARTMENT DIVIDER RETAINERS. *EH

3442

Service Bulletin/Repair Instructions

TRANSMISSION FLUID LEAK FROM WEEP HOLE AT THE REAR OF THE TRANSMISSION. *TT

3451

Service Bulletin/Repair Instructions

SLIP CONDITION IN 2ND 3RD OR 4TH DAMAGED 2-4 BAND 3-4 CLUTCH. 2005 ALL FULL-SIZED TRUCKS AND UTILITIES/2005 ALL MID-SIZED TRUCKS AND UTILITIES *SC

3474

Service Bulletin/Repair Instructions

ERRATIC FUEL GAUGE - SERVICE VME. *TT

3489

Service Bulletin/Repair Instructions

NO CRANK, TRANSMISSION RANGE INDICATOR INOPERATIVE. *SC

3513

Service Bulletin/Repair Instructions

INTERMITTENT BLOCK OUT OF FIRST GEAR FROM A STOP. *TT

3537A

Service Bulletin/Repair Instructions

DRIVERS INFORMATION CENTER SWITCHES INOPERATIVE. *TT

3540

Service Bulletin/Repair Instructions

SERVICE VME - FRONT TURN SIGNAL BULB INOPERATIVE AT TIMES. *TT

3551

Service Bulletin/Repair Instructions

SERVICE VME - FUEL GAUGE ERRATIC OR DEFAULTS TO EMPTY. *TT

3567

Service Bulletin/Repair Instructions

SPEED SENSITIVE WIPERS INOPERATIVE. *SC

3588

Service Bulletin/Repair Instructions

SEVERAL RIGHT FRONT SEAT BELT ASSEMBLIES HAVE BEEN RETURNED THROUGH THE 100% LAUNCH PART RETURN PROCESS WITH A CUSTOMER COMPLAINT OF SEAT BELT DIFFICULT TO LOWER PAST STITCHING ON SEAT BELT WEBBING. *TT

3608

Service Bulletin/Repair Instructions

INFORMATION TO UPDATE BULLETIN 05-06-01-001C FOR CRANKSHAFT HARMONIC BALANCER FRICTION WASHER. *TT

3609A

Service Bulletin/Repair Instructions

HARSH 1-2 SHIFT, MALFUNCTION INDICATOR LAMP ILLUMINATED, DIAGNOSTIC TROUBLE CODE P0894 STORED IN PCM. *TT

3630

Service Bulletin/Repair Instructions

FUEL TANK PRESSURE SENSOR READING. *TT

3673

Service Bulletin/Repair Instructions

CRUISE CONTROL INOPERATIVE AND/OR MALFUNCTION INDICATOR LAMP ON WITH DIAGNOSTIC TROUBLE CODE P0833 STORED. THE CONDITION MAY NOT BE ABLE TO BE DUPLICATED BY THE DEALER YET THE CONSUMER MAY HAVE A REPEAT CONCERN. *AK

3761

Service Bulletin/Repair Instructions

WIPERS WILL NOT PARK. *TT

3775

Service Bulletin/Repair Instructions

CROSS DRILL BRAKE ROTORS ROTATIONAL APPEARANCE. *TT

3778

Service Bulletin/Repair Instructions

HEADLAMP LENSES HAVE LIGHT FOG OR MOISTURE. *TT

4159

Service Bulletin/Repair Instructions

REVISED FUEL SENDER VALUES FOR THE CHEVROLET CORVETTE AND CADILLAC XLR. *KB

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.

2005 Chevrolet Corvette Service Bulletins: 608 bulletins | CarFathom