PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5099J
PI to help diagnose A/C concern
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP5700G
This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when ordering
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIP5700F
This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when ordering
PIP6088
This PI Addresses a possible solenoid wiring fault and how to inspect the build date to identify
PIP6086
This PI advises dealers to inspect for a missing pump gasket if the vehicle exhibits no movement following a VB replacement
13598
New Vehicle Monitoring Programs Section in IVH
22-NA-080
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of engine related shudder.
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
N252494770-01
Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the affected vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.
N252494770
Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the applicable vehicles will be mailed an owner’s manual and warranty insert containing this information in English and Spanish.
PIT6180A
This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
15-NA-010
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
25-NA-100
This warranty administration bulletin provides policy information on vehicles outside of a California Emissions State who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
PIP5943A
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
25-NA-065
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP5966A
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
05-03-07-009L
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
11-00-89-005Y
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-08-51-001L
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
16-NA-003
This service bulletin provides repair information to correct a customer concern of a chirp, squeak noise heard coming from the rear of vehicle.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
16-NA-019
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
22-NA-244
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
01-08-42-001Q
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
17-NA-331
This service bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
20-NA-166
This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT6261
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
17-NA-271
This service bulletin provides a procedure to clean the back side of the rims and rotors and to correct the customer concern of wheel clicking.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
24-NA-254
This service bulletin informs GM service personnel that the LT4 service engine current part number 12679879 is no longer available from General Motors. If this part is needed to service a customer vehicle, an alternate engine is available that will need to be reworked by the technician.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
PIP6014
This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to contact Technical Assistance to make sure unit is not suspect of a snap ring concern prior to installation.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
17-NA-239
This bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of time.
16-NA-059
This service bulletin provides information for cleaning the brake calipers that may have staining/discoloring on the paint of the brake caliper.
17-NA-078
This service bulletin provides information on Corvette and Camaro Exhaust Tone During Wide Open Throttle while in Sport or Track Modes and that this is considered a normal characteristic.
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PIP5621E
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
13-03-10-001L
This service bulletin provides information on summer tire performance and tire cold weather cracking.
99-00-89-019Z
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
23-NA-154
This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
17-NA-087
This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIP6000A
This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.
PIP5996A
This Preliminary information communicates diagnostic information for vehicles with transmission noise.
PIP6000
This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5996
This Preliminary information communicates diagnostic information for vehicles with transmission noise
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIT6180
This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
20-NA-038
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
23-NA-142
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
23-NA-125
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME) FAQs.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP5968
This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to transmission installation.
PIP5966
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update
PIP5395H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
22-NA-246
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension housing and to perform testing on transmission for other possible issues, but it still may be possible on high mileage vehicles that orifices in housing may have come dislodged, causing the same customer concern.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
16-NA-361
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle.
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIP5700E
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17-NA-040
This service bulletin provides a procedure to correct a condition of Brake Squeal or Squeak Noise Intermittently on Initial Brake Applies.
19-NA-046
This informational bulletin provides information for dealers, technicians and customers on the eLSD Wheel Slip Display in DIC.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
PIP5943
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and repair of 8 Speed Transmissions
23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States.
13-03-10-001K
This service bulletin provides information on summer tire performance and tire cold weather cracking.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC6378C
This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP4112T
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
09-04-20-001H
This service bulletin provides information to address a tire chatter noise during low speed tight turn conditions (i.e. parking lot, driveway, etc.) primarily during cooler ambient temperatures.
PIP5621D
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
17-NA-408
This service bulletin informs the technician that if the vehicle has an engine misfire with DTC P0300 set, and superchargerâs cooling system has been previously repaired, it must be properly evacuated and filled.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
09-06-04-026X
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5395G
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
01-08-42-001P
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
15-06-01-002O
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
13-03-10-001J
This service bulletin provides information on summer tire performance and tire cold weather cracking.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
15-06-01-002N
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
20-NA-187
This service bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of Transmission Shift After Vehicle Sitting with Engine Off.
15-06-01-002M
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
22-NA-257
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-216
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PIT5698C
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5621C
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
22-NA-184
This informational bulletin advises the technician of possibly installing the incorrect 1-2-7-8-R clutch fluid passage seal and which seal should be used with measurements of the seal.
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-176
This technical bulletin provides information on a possible bolt and guide pin that may be missing from the control valve which will need to be installed to correct the repair.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
18-NA-268
This service bulletin provides a procedure to correct a condition of a rattle noise heard from the front of the vehicle when the engine is running at slower speeds.
04-00-89-015X
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
PIC6464
This Preliminary Information is to assist dealership technicians in diagnosing a complaint related to the variable red line feature surrounding the tachometer gauge.
PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
PIP5212D
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
14-06-04-004H
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.
PIT5745D
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.
09-04-20-001G
This informational bulletin provides information to address a chatter noise during low speed tight turn conditions (i.e. parking lot, driveway, etc.) primarily during cooler ambient temperatures.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
15-06-01-002L
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
13-03-10-001I
This service bulletin provides information on summer tire performance and tire cold weather cracking.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
20-NA-207
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
PIC6378B
This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.
22-NA-047
Information bulletin explains a possible coolant leak coming from the cylinder head bolt areas.
PIC6450
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States.
PIT5745C
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
22NA018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
990089019W
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
18NA067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
16NA361
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First Start Up/Shift of the Day Under Light Throttle.
18NA073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
22NA012
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
070316004D
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
000090002L
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
20NA166
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
17NA040
This service bulletin provides a procedure to correct a condition of Brake Squeal or Squeak Noise Intermittently on Initial Brake Applies.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
20NA132
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698B
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
21NA152
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.
PIC6439
This Preliminary information communicates a diagnostic tip to dealership technicians when diagnosing a B1517 DTC.
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
110089002E
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
070089037Q
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
PIP5621B
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
130310001H
This service bulletin provides information on summer tire performance and tire cold weather cracking.
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
17NA087
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
21NA109
This service bulletin provides diagnostic information for a customer concern of engine vibration.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
21NA068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
20NA038
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this occurrence.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
070089036J
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5212C
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5745B
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
PIP5784
This Preliminary information communicates to the dealer technician to inspect for a missing 1-2-7-8-R clutch fluid passage seal or incorrect 1-2-7-8-R clutch fluid passage seal being install for a no movement concern after valve body replacement on the 8L45 or 8L90 transmissions.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
N202302720 01
Special Coverage. Certain vehicles may have a condition where the vehicle may overheat and enter a reduced power mode when driven on a track at sustained high speeds in high ambient temperatures. Dealers are to install an updated radiator package and, for automatic transmission vehicles, updated shift-point calibration software. The repairs will be made at no charge to the customer. The customer must provide evidence of an overheating condition in the form of one of the following: Diagnostic Trouble Code, photos, videos, documented complaints of overheating prior to the special coverage, or a track receipt. The dealer should make a copy of any customer evidence provided and file with the warranty claim.
19NA217
This technical bulletin provides a service procedure to correct conditions of Manual Transmission Stalling, Clutch Chatter or Hard Shifting into 1st Gear/Reverse and Automatic Transmission Vibration on Launch or Engine Noise.
150601002K
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
N202302720
Special Coverage. Certain vehicles may have a condition where the vehicle may overheat and enter a reduced power mode when driven on a track at sustained high speeds in high ambient temperatures. Dealers are to install an updated radiator package and, for automatic transmission vehicles, updated shift-point calibration software. The repairs will be made at no charge to the customer. The customer must provide evidence of an overheating condition in the form of one of the following: Diagnostic Trouble Code, photos, or videos. The dealer should make a copy of any customer evidence provided and file with the warranty claim.
010601011L
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
090604026S
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
040089015V
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
16NA019
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIC6208E
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
PIC6378A
This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16NA059
This service bulletin provides information for cleaning the brake calipers that may have staining/discoloring on the paint of the brake caliper.
17NA271
This bulletin provides a procedure to clean the back side of the rims and rotors and to correct the customers concern of wheel clicking.
19NA046
This informational bulletin provides information for dealers, technicians and customers on the eLSD Wheel Slip Display in DIC.
060089026Q
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
130310001G
This service bulletin provides information on tire cold weather cracking and the proper techniques on taking care of the tires and proper use.
17NA408
This service bulletin informs the technician that if the vehicle has an engine misfire with DTC P0300 set, and supercharger?s cooling system has been previously repaired, it must be properly evacuated and filled.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
20NA207
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
17NA239
This bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of time.
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
17NA078
This informational bulletin provides information on Corvette and Camaro Exhaust Tone During Wide Open Throttle while in Sport or Track Modes and that this is considered a normal characteristic.
990089019U
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698A
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
20NA041
This technical bulletin provides a procedure to replace the left side differential carrier cover and seal to correct a condition of Warble Noise from the Rear of the Vehicle.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
150089002B
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5741
This Preliminary information communicates to the dealer technician that if after replacing the valve body on an 8L45 or 8L90 transmission the vehicle will not move the valve body may be missing a plug and retainer bolt. Technician's are instructed to obtain and install a plug and retainer bolt kit from the GM Warranty Parts Center to address this concern.
990089019T
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
19NA010
This informational bulletin provides information for dealers/technicians on Head-Up Display (HUD) on Vehicles Model Year 2017 and Newer Having Rotational Feature that Allows for Adjusting of Angle of HUD Image.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIT5745
This Preliminary information communicates and issue with the memory seat module waking up the low speed GM lan bus and causing a battery draw.
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
140604004G
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIP5700C
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
20NA098
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
150601002J
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
19NA035
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended, causing the parking pawl to engage while driving.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
18NA355
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
140604004F
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.
150601002I
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL Illuminated.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
PIP5700B
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
060089026P
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
990089019S
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
040089015U
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
050307009J
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
150089005C
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
15NA040
This technical bulletin provides repair information for replacement of the drive belt tensioner to correct a customer concern for a rattle noise at 48 km/h (30 mph) to 64 km/h (40 mph) when the engine is switching between V4 and V8 and/or they notice fluid leaking from the bellow on top of the tensioner.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
110089002D
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
19NA212
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away to correct a crank/No Start condition.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
15NA010
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
PIP5700A
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5700
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
PIP5130K
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
PIP5531A
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
PIC6378
This Preliminary Information communicates helpful information on diagnosing general customer concerns related to a power folding top.
PI0592F
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
19NA073
This technical bulletin provides repair information to correct conditions of difficult to shift into gear, grinds when shifting, possible gear clash, intermittent gear pop out and/or mushy shifts.
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5330D
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
PIP5621A
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
18NA137
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended cranking condition.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
18NA172
This technical bulletin provides a procedure to modify the right rear exhaust control valve actuator to correct a rattle noise heard from the rear of the vehicle.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIE0529A
This engineering information bulletin ends the need for information from the field on an Intermittent No Forward and/or No Reverse While Driving condition. If this condition is encountered, refer to SI for further diagnosis.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
130417001B
This informational bulletin provides information on Driveline Support (Torque Tube) / Propeller Shaft Input to Front Hub Bearing Alignment.
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP5407B
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
PIP4670H
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP5407A
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
PI0592E
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
090604026R
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
130089008B
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PIP4158H
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
PIE0529
This engineering information bulletin is requesting information from the field to validate a field fix. Before contacting engineers, remove the transmission oil pan and inspect for nickel to quarter size pieces of aluminum debris in the oil pan. The 2-3-4-6-8 and 4-5-6-7-8 reverse clutch assembly and the 1-3-5-6-7 clutch assembly may be broken in several pieces.
PIP5663
This Preliminary information communicates AFM / DFM usage Information. providing additional information on the AFM and DFM systems
PIT5698
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIC6208D
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
19NA142
This technical bulletin provides information for new transmission oil to use, a procedure for exchanging the old fluid and adding the new fluid to a service transmission.
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIC6065C
This Preliminary Information communication provides information to the technician about vehicles that do not recognize the SD card when it is used in the Performance Data Recorder (PDR) system. The SD card needs to be formatted to FAT32 and also have a class 10 designation in order to be compatible with the system.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
090604026Q
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
17NA355
This technical bulletin provides repair information to correct a customer concern of the paint peeling on a front and/or rear fascia.
18NA268
This technical bulletin provides a procedure to correct a condition of a rattle noise heard from the front of the vehicle when the engine is running at slower speeds.
19NA140
This informational bulletin provides information to the tech to replace only the prop shaft and not the complete driveline support assembly (DSA) if a rattle noise is confirmed to be coming from the prop shaft.
PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
PIP5498L
This Preliminary information communicates A vehicle may have a concern of DTC P050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
140604004E
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold or the vehicle has sat for a few hours.
19NA088
This technical bulletin provides a procedure to reposition the coolant surge hose clamp away from the hood blanket to avoid hood closing interference.
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5423B (1)
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
PIP5423B
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
PIP5423A
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
030729004L
This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.
PIP4670F
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004Y
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
16NA111
This informational bulletin provides diagnostic/inspection information for the air box and air filter seal to correct a MIL and DTCs P0420 and P0430 setting.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP5526A
This Preliminary Information communication advises the technician that the Product Quality Center part restriction has ended for the 8L45 and 8L90 park actuator rod.
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
19NA054
This technical bulletin provides repair information to correct a customer concern of hearing a door rattle noise from outside of vehicle during high radio volume or high bass levels.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
150601002H
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIC6009B
This Preliminary Information communication provides information to the technician about customers that may inquire as to whether or not a rear sway bar can be added to a vehicle that was not originally equipped with one. The rear sway bar is part of the Z51 Performance Package. General Motors does not recommend or support this modification.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010310003R
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
16NA201
This informational bulletin describes the new process for shipping ground effect components and other loose shipped parts for new vehicles.
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
16NA175
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
PIT5444D
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
PIP5554A
This Preliminary information communicates P0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
030603004X
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17NA066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5212B
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
PIP5311D
This Preliminary Information communication provides information to the technician about vehicles that have a hot temp message. Any time the maximum recommended temperatures are reached in any condition, the Driver Information Center will give warnings at the appropriate time for coolant, oil, or transmission fluid. A cool-down lap or two will bring operating temperatures back to a reasonable level and aggressive track driving can be resumed.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
000310003X
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
18NA336
This technical bulletin provides a procedure for replacing the emblem on the seat cover as opposed to replacing the whole seat cover itself.
PIE0475A
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
PIP5159C
This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308 may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.
PIP5395E
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
PIP5601
This Preliminary information communicates
PIP4138R
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIC5985C
This Preliminary Information communication provides information to the technician about customers that would like to install Regular Production Option Code NPP (Dual Mode Performance Exhaust System) to a Stingray that was produced without the option. Do not attempt to add Regular Production Option Code NPPto a car that was not manufactured with it. General Motors does not support the software changes that are required.
PIP5576
This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
PIP5553A
This Preliminary information communicatesThe vehicle may have an ses lamp with any of the following DTC P06DA, P06DB, P06DC, P250A, P0300, P0340, P0341, P0335, P0336, P0641, P0011, P0010, P2088, P2089, and/or P2230. Possible crank no start or a stall. possible wiring jumper harness chaffed at the bolt at the X154 connector on lower left side of the frount cover.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5455C
This Preliminary Information communication provides information to the technician about vehicles that have a rattle or flutter noise from the supercharger tensioner and belt. Dealer shouldReplace the supercharger belt with aGates Belt P/N K080852HD.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIC5960E
This Preliminary Information communication provides information to the technician about vehicles that have the base power seat, Memory Recall, and Easy Exit Recall functions may seem erratic or seem to operate intermittently. Technician should become familiar with the following areas of the power/ memory seat system will aid in assisting customers with its functionality, limit switches, unsupervised / supervised movements, auto memory recall (if equipped), Easy Exit Recall (if equipped), and the difference between the manual transmission and automatic transmission.
18197
18197 - Customer Satisfaction Program. Certain vehicles, equipped with (RPO FE6) suspension system-ride, handling, and performance, may have an incorrect service calibration for the suspension control module, which may not provide the softer, higher quality ride improvement as intended. Dealer will reprogram the suspension control module.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5508B
This Preliminary Information communication advises the technician that the Product Quality Center has ended the part restriction for the T87A Transmission Control Module.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5498K
This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
PIP5373B
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
PIT5411M
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP5498J
This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5498H
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
18149
18149 - Customer Satisfaction Program. Certain vehicles may have a condition in which, the front and/or rear spring strap retainer bolts, and the front and/or rear stabilizer shaft clamp bolts may not have achieved the intended torque value. Under-torqued fasteners could result in suspension noise or shortened service life of components. Confirm the torque of the identified fasteners or replace the fasteners if bolts are one-time use. The Service Procedure below includes VIN specific information on which fasteners must be serviced for each affected vehicle.
18NA141
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
18NA134
This technical bulletin provides a procedure to test the radios receiver if certain XM channels cut out (mutes) depending on location of the vehicle.
18NA138
This technical bulletin provides a procedure to replace the HMI module to correct a condition of Radio Control (ICS) Display Does Not Remain Off at Times after it Has Been Turned Off in the Radio Settings Menu due to a software concern.
150603002M
This bulletin provides information on approved warranty part numbers for original equipment batteries.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
17NA072
This informational bulletin provides information on Installation of Stage One and Two Rear Wicker Bills on Spoiler.
18NA129
This informational bulletin provides information on Oil Change Information for Chevrolet Corvette.
PIC6328A
This Preliminary Information communication provides information to the technician about vehicles that when a phone does not charge properly or charging cycles is on and off rapidly when connected to the single port USB hub of the vehicle. Technician should check the Human Machine Interface part number Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern if the Human Machine Interface part number ends in 8433. Technician should follow published Service Information diagnostic if the Human Machine Interface part number is not 8433.
18NA039
This technical bulletin provides a procedure to reprogram the memory set module to correct a condition of Personalization Selections Intermittently Missing from Comfort and Convenience Menu due to a calibration concern.
18NA125
This informational bulletin provides information for engine oil life monitor operation calculation.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
PIC6061C
This Preliminary Information communication provides information to the technician about diagnosing a vehicle that has a "Change Brake Pads" message that appears in the Driver Information Center. Technician will need to first inspect the brake pad wear sensor harness for damage.
PIT5411L
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
150603002L
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIC6328
This Preliminary Information communication provides information to the technician about vehicles that when a phone does not charge properly or charging cycles is on and off rapidly when connected to the single port USB hub of the vehicle. Technician should check the Human Machine Interface part number Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern if the Human Machine Interface part number ends in 8433. Technician should follow published Service Information diagnostic if the Human Machine Interface part number is not 8433.
16NA363
This informational bulletin provides information on what to do with the loose shipped brake cooling deflectors, duct and metal wheel blocker rings while performing the pre-delivery inspection.
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIP5179D
This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of port fuel engines.
010310003Q
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIC6315C
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
PIP5498G
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
18NA088
This informational bulletin provides the information on what may occur if the charge air cooler is not filled and drained properly after a service or replacement has been completed.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
PIT5411K
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, and displays are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP4112S
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
110089002C
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIC6084C
This Preliminary Information communication provides information to the technician about having difficulty seating the beads on the tires. If this issue is encountered at the dealership technicians are to review May 2015 Emerging Issues Broadcast to address this concern.
17NA369
This technical bulletin provides a procedure to program the RDCCM if the DTC C0407 is set.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
17NA337
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
PIP5136A
This Preliminary Information communication provides information to the technician about vehicles that have an engine oil odor with no oil leaks found. Technician will need to inspect for an external oil leak. Technician will need to ensure the oil level is correct. Technician will need to replace the rear main seal, if no oil leaks were found and the engine oil level is not over full.
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PIC6315B
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
PIP5395D
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
18038
18038 - Service Update. The harness branch from the main body wiring harness (MBWH) to accelerator pedal may be pinched underneath the dead pedal bracket. There may be an intermittent check engine light and reduced engine power. Dealers are to inspect for pinched wires and repair as necessary.
PIP5554
This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
PIT5411J
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP4670E
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIP5553
This Preliminary information communicatesThe vehicle may have an ses lamp with any of the following DTC P06DA, P06DB, P06DC, P06B6, P06B7, P250A, P0300, P0340, P0341, P0335, P0336, P0641, P0011, P0010, P2088, P2089, and/or P2230. Possible crank no start or a stall. possible wiring jumper harness chaffed at the bolt at the X154 connector on lower left side of the frount cover.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
150603002K
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIE0405C
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a Torque Converter Shudder.
18NA027
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP4138Q
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
PIP5498F
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
18NA022
This technical bulletin provides a procedure to reprogram the instrument panel to correct a condition of Instrument Cluster Goes Blank or Tell Tale Indicators Remain On due to a software issue.
PIC6084B
This Preliminary Information communication provides information to the technician about having difficulty seating the beads on the tires. If this issue is encountered at the dealership technicians are to review May 2015 Emerging Issues Broadcast to address this concern.
PIP5446A
This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100864002D
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
PIP5168F
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIP5330C
This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
PIP5130J
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
17NA074
This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or Apple CarPlay.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
PIC6299A
This Preliminary Information communicates several possibilities of what may be causing a fluctuating tachometer.
130417001A
This informational bulletin provides information on Driveline Support (Torque Tube) / Propeller Shaft Input to Front Hub Bearing Alignment.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIP4578B
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
PIT5354B
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
150601002F
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the customers concern of engine misfire, ticking noise and/or MIL on.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
PIP5498E
This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
150603002J
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
16NA239
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
17NA386
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
150603002I
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
17NA344
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
PI1149A
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
PI1535B
This preliminary information bulletin provides a procedure to install a power steering gear cooling duct for track use to decrease temperature with the steering gear.
17NA142
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
17NA375
This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or pixelated
PIC6315A
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
17NA297
This informational bulletin provides information for assisting the customer in setting the position for the memory mirror and the reverse tilt
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
PIC6315
This Preliminary Information communication provides information to the technician about vehicles that in the radio settings some of the vehicle personalization selections within the Comfort and Convenience menu are missing at times. Technician will need to perform a scan for Diagnostic Trouble Codes. Technician will need to follow published Service Information diagnostics if there are Diagnostic Trouble Codes present. If the concern is and intermittent this Preliminary Information communication will be updated with a repair. When the personalization selections are not missing from the Comfort and Convenience menu but they are missing from other menus such as the Climate and Air Quality, Collision/Detection Systems, and Lighting menus, refer to bulletin 17-NA-086. Memory seat adjustments may not be available tech will need to perform a Memory Seat Module replacement/programming.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIP5531
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
PIP5526
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the 8L45 and 8L90 park actuator rod. The dealer technician is advised to call the GM Product Quality Center for further assistance.
17NA331
This informational bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
PIP5395C
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
PIP5508A
This Preliminary Information communication advises the technician that the Product Quality Center has a part restriction for the T87A Transmission Control Module. The dealer technician is advised to call the GM Product Quality Center for further assistance.
PIE0405B
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a Torque Converter Shudder.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
150603002H
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
17-NA-311
Rattle Type Noise/Sound from the Drive Support Assembly (DSA) Condition Some customers may comment on a rattle type noise. Further investigation will reveal the noise is originating from the drive support assembly area. Cause This may be due to the propeller shaft hub clamp bolt coming loose. Correction Replace the propeller shaft hub clamp bolt.
17-NA-337
All or Some Options May Be Missing from Driver Information Center (DIC) Info Pages Menu Due to Them Not Being Selected Condition Some customers may comment that with the Info option selected from the main menu (1), the Info Pages are blank (2) when scrolling up and down. If information is present when scrolling up and down, they may also comment that certain items are missing when compared to other like vehicles Cause This condition may be caused when all/some of the options not being selected in the active info pages menu. Correction If this concern is encountered, determine if all/any of the selections in the active info pages menu are not selected. To do this, follow the steps listed below.
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIE0405A
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of a Torque Converter Shudder.
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
000601012H
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
16NA250
This bulletin provides information on replacing the prop shaft hub clamp (AT) or the input shaft frt bearing (MT) whenever the driveline support assembly has been removed for repair.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
150603002G
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIC6296A
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
03-08-46-004T
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIT5411H
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
17-NA-264
This technical bulletin provides information to reprogram the ECM to correct a condition of MIL Illuminated and DTC P0106 Set.
PIC6302
The PI was created to advise of an engineering investigation for a concern of unable to connect toOnStar Virtual Advisor when selecting "New Destination" in the OnStar menu.
PIP5248D
This Preliminary Information communication provides information to the technician on the steps need to diagnose and repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
16-NA-111
This technical bulletin provides a procedure to perform diagnosis before just replacing the battery sensor module.
PIP5212A
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise. Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
PIC6296
This Preliminary Information communication provides information to the technician that when scanning a vehicle for Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
17-NA-242
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
17-NA-230
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided.
PIC6065B
This Preliminary Information communication provides information to the technician about vehicles that do not recognize the SD card when it is used in the Performance Data Recorder (PDR) system.The SD card needs to be formatted to FAT32 and also have a class 10 designation in order to be compatible with the system.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
17-NA-072
This informational bulletin provides information on Information on Installation of Stage One and Two Rear Wicker Bills on Spoiler.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.