PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5099J
PI to help diagnose A/C concern
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
22-NA-007
This service bulletin provides procedures to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, Charge Air Cooler (CAC) Icing - Malfunction Indicator Lamp (MIL) Illuminated with DTCs P0299, P0234, P0236, P2227, P00C7 Set.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
15-NA-010
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
PI0281L
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when addressing underbody component corrosion with customers.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
25-NA-087
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use for certain repairs, such as Wiring Harness Repairs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
24-NA-098
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
25-NA-065
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.
08-03-10-006I
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIT5994A
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
05-03-07-009L
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
11-00-89-005Y
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-08-51-001L
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PIP5358D
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
01-08-42-001Q
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
09-06-04-026Z
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
18-NA-263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PIT5074Q
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT6261
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
PIP4723J
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5698E
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIT5569C
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIP6015
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
24-NA-225
This bulletin provides information on how to look for and test for DEF or water in the fuel system and what the specs should be.
24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
24-NA-223
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
01-06-01-011Q
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
PIP5621E
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
99-00-89-019Z
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
23-NA-154
This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
20-NA-138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
08-07-30-026I
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
PIT5099H
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
PIC5650L
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
PIP5569B
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
09-06-04-026Y
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
01-06-01-011P
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
24-NA-147
This service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
18-NA-306
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
19-NA-101
This service bulletin provides a procedure to replace the intake manifold if diagnostics has found the Non Return Valve missing to correct customer concerns of possible oil consumption and//or leaks.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
21-NA-268
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated or Possible Increased Brake Pedal Effort.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
00-03-10-006P
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5596A
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
19-NA-044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16-NA-338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
PIT6122
This Preliminary information communicates to dealers of a known issue with failed map update
20-NA-024
This service bulletin provides a information and diagnostic steps/tips for vehicles that are slow to heat up in cold temperatures.
PI0281K
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PI0592I
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
PIT5074P
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT5214F
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
20-NA-159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
23-NA-065
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing Vehicle from Canada to the United States.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
01-06-01-011O
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
10-00-89-006J
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5698D
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
07-08-49-020R
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP5621D
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
PIP5628G
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
PIP5358C
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
21-NA-026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
PIP4902R
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
01-06-01-011N
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
99-08-51-001F
This service bulletin provides information on Paintless Dent Repair Process.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIT4261J
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
04-07-30-013E
This service bulletin provides information to dealership personnel on automatic transmission shift and engine driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
08-07-30-026H
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
PIC5650K
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
01-08-42-001P
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement Guidelines.
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PIP5628F
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
PI0281J
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PIT5994
This Preliminary information communication provides information to the technician with diagnostic tips for diagnosing reduced or low engine power with no Driver Information Center messages, that may be caused by an inaccurate brake pedal position sensor.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
22-NA-067
This service bulletin provides a repair procedure to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, PCV Bypass Hose and Charge Air Cooler Icing for LUV Engines, Malfunction Indicator Lamp (MIL) Illuminated.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
PIP5895A
This Preliminary information communicates to the technician the need to inspect connector for moisture intrusion at ECM, procedure for verification of need for replacement
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
01-08-42-001O
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
N222372590-02
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less).
00-00-90-002M
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
07-03-16-004E
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
20-NA-047
This service bulletin provides a service procedure to correct customer concerns of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set.
23-NA-001
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
N222372590-01
Service Update. Certain vehicles may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less). Dealers will install a TCV thermal wrap and, if applicable, reprogram the Engine Control Module.
PIP5812C
This Preliminary information communicates the possibility of dtc p0299 p0234 setting due to oil/moisture cndensate freezing in Turbocharger Wastegate Regulator Solenoid Valve (TCV) during cold weather driving
PIC5611H
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
N222372590
Service Update. Certain vehicles listed above may have a condition in which ice or sludge can accumulate in the Charge Air Cooler (CAC) or Closed Crankcase Ventilation (CCV) system when driving in extremely cold weather conditions (-18°C (0°F) or less). Dealers will install a TCV thermal wrap and, if applicable, reprogram the Engine Control Module.
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5895
This Preliminary information communicates to the technician the need to inspect connector for moisture intrusion at ECM, procedure for verification of need for replacement
PIP5540J
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIP5632G
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP4902Q
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
18-NA-171
This service bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL Illuminated.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5598D
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
16-NA-290
This service bulletin provides repair information to correct a customer concern that Radio is Theft Locked.
16-NA-292
This service bulletin provides repair information to correct a customer concern of Phone Icon on Radio Display Intermittently Will Not Respond or Spins When Pressed.
15-NA-087
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system.
22-NA-205
This service bulletin provides information on Module Harvesting.
10-00-89-006I
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
PIT5698C
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PI0592G
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
09-06-04-026W
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
PIP5621C
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
01-06-01-011M
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
04-00-89-015X
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
22-NA-143
This service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions equipped with IOB Radio.
PIT5569B
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT4261H
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
PIC5260F
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099F
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP5849A
This Preliminary information communicates to the technician the need to inspect the induction system for potential restriction and blockage in the induction system creating drive ability issues.
PIP5856
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable diesel fuel.
22-NA-106
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE) Tires and PDI installed Limited Production Option (LPO) Tires.
12-00-89-003B
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIP5849
This Preliminary information communicates to the technician the need to inspect the induction system for potential restriction and blockage in the induction system creating drive ability issues.
PIC5260E
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PI0281I
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIP4670J
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC6450
This Preliminary information communicates a process to correct the concern of Unable to contact OnStar after the 3G EOL on 2015-2022 model year vehicles in the United States.
PIT3271L
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
080089014G
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
22NA018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
990089019W
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
070601016G
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
150089004D
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
18NA067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
PI0653F
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
18NA073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP4902P
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
22NA007
This service bulletin provides procedures to correct customer concerns of Poor Engine Performance in Extremely Cold Weather Conditions, Charge Air Cooler (CAC) Icing - Malfunction Indicator Lamp (MIL) Illuminated with DTCs P0299, P0234, P0236, P2227, P00C7 Set.
PIP4723F
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5632F
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5835
This Preliminary information communicates the possibility of increased brake pedal effort due to vacuum pump failure
22NA009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
070316004D
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
16NA380
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe.
19NA237
This informational bulletin explains how to identify possible DEF contamination.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
18NA260
This service bulletin provides a procedure for A/C Leak Test and Receiver/Dehydrator Plug replacement due to refrigerant loss.
000090002L
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
050604022S
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
1308116001G
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
18NA033
This bulletin provides information for the low oil pressure light on at idle, which may be caused by oil pressure being bled off due to debris in the oil drain check valve and/or a smashed oil filter.
21NA268
This service bulletin provides diagnostic/repair information to correct customer concerns of a Crank No Start or Extended Crank, Malfunction Indicator Lamp (MIL) Illuminated.
030310007K
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance, Shake, Flat Spotting) of GM Original Equipment Tires.
19NA104
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
030091001H
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIP5812B
This Preliminary information communicates the possibility of dtc p0299 p0234 setting due to oil/moisture cndensate freezing in Turbocharger Wastegate Regulator Solenoid Valve (TCV) during cold weather driving
PIT3099U
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
20NA132
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIP5812A
This Preliminary information communicates the possibility of dtc p0299 p0234 setting due to oil/moisture cndensate freezing in Turbocharger Wastegate Regulator Solenoid Valve (TCV) during cold weather driving
PIC5650J
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698B
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
21NA150
This service bulletin provides repair information to correct a customer concern of seeing moisture, condensation in one of the headlamp assemblies.
21NA152
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint percentage.
PIP5812
This Preliminary information communicates the possibility of dtc p0299 p0234 setting due to oil/moisture cndensate freezing in Turbocharger Wastegate Regulator Solenoid Valve (TCV) during cold weather driving
010842001N
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIT4261G
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
990420002L
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
PIP5632E
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035E
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
110089002E
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
070089037Q
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
PIP5621B
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
PIP5495N
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
21NA124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA).
070089037P
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
100089006H
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIT5214E
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
20NA159
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
19NA044
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions and improve fuel economy.
16NA338
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
21NA103
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and that it is considered a normal condition.
000601026N
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
18NA171
This service bulletin provides a procedure to repair the mechanical components and then reprogram the throttle body to prevent the conditions of a rough running engine, MIL Illuminated.
050308002I
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
20NA047
This service bulletin provides a service procedure to correct conditions of Front or Rear Crankshaft Oil Leak, MIL Illuminated with DTC P1101 Set.
020089002T
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
070089036J
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5260D
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5540G
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5495M
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
PIP5725A
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
110089005Q
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
20NA024
This service bulletin provides a information and diagnostic steps/tips for vehicles that are slow to heat up in cold temperatures.
1008110001I
This informational bulletin provides information on proper use of floor mats.
20NA138
This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
21NA043
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
16NA109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
21NA026
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats warped or misshapen.
010601011L
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
040089015V
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
16NA019
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
990851001E
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
PIP5353F
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
1308116001F
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
19NA080
This informational bulletin provides information to the tech to discard the PCV drain tube when working on the lower area of the engine.
060089026Q
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
18NA118
This Diagnostic tip explains how an air cleaner installed incorrectly can cause the DTCs to set and provides a procedure to correctly install an air cleaner without damaging the air cleaner bracket.
990089019U
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
17NA184
This informational bulletin provides information for dealers and technicians about the 1.4L and 1.8L turbocharged engines that use two different suppliers for the oil filter housing, which results in two different filters being used.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698A
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
20NA144
This technical bulletin provides repair information to correct a customer concern of Check Engine Light Illuminated, DTC P0606 Set in Engine Control Module.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
150089002B
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
990089019T
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
PIC5852C
This Preliminary Information communication provides information to the technician about vehicles that when attempting to start vehicle "No Fob Detected" message is displayed. Technician will find the Key FOB works and the vehicle will start with the key FOB is placed in the pocket. Technician will need to replace the Key FOB with the Key FOB with Passive Entry Passive Start.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP5598B
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
16NA383
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
20NA098
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
000310003Z
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S. Dealers Only).
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIP5647A
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Engine oil level will be found over full and have a fuel odor. It will be found that the Engine oil is diluted with fuel. Small gas engines (SGE) May only have the engine oil level over full and have a fuel odor. It will be found that the Engine oil is diluted with fuel. This concern is caused by marshalling the vehicle around the lot before it is sold and/or short driver cycles.
20NA093
This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at Times After Being Turned Off in Settings and no parts should be replaced due to this condition.
PI0281H
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
20NA056
This technical bulletin provides a procedure to add a sealant around the rear spoiler mounting studs to eliminate water intrusion into the trunk.
060089026P
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated (CCND) Labor Operation Numbers.
17NA198
This technical bulletin provides a procedure to disengage the jammed parts and release the gears for proper function caused by the mechanical of the height adjustment being jammed, not broken creating a condition of difficult to adjust the seat height and/or seat stuck mostly in lowest position.
990089019S
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
17NA152
This technical bulletin provides repair information to correct a customer concern of front seat slight rocking movement while shifting weight from seat, during hard stops, and/or when driving over rough road surface.
040089015U
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
000310003Y
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
PIP5417C
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. The technician is directed to perform the testing and to check related components based on the results.
050307009J
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM Vehicles.
150089005C
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S. Only).
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
17NA233
This technical bulletin provides a procedure to correct a condition of an MIL Illuminated with DTC P0446 Set.
PIP5495L
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
110089002D
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
050307009I
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
15NA010
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT5726
This preliminary information discusses a potential odor issue from the HVAC case and a temporary resolution.
PI0592F
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5621A
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080310006G
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
PIP5370E
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
100089006G
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5495K
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010601011K
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
100089009C
This informational bulletin provides information on key code security and information on GM key code look up applications.
PIP5517C
This Preliminary information communicates the following to the dealer. If an engine oil leak has been isolated to the front crankshaft seal, check for misfires low engine compression and/or cylinder leakage readings. These issues could cause excessive positive crankcase pressure leading to engine oil leaks.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
PIP5517B
This Preliminary information communicates the following to the dealer. If an engine oil leak has been isolated to the front crankshaft seal, check for misfires low engine compression and/or cylinder leakage readings. These issues could cause excessive positive crankcase pressure leading to engine oil leaks.
PIP4670H
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
N192265370
N192265370 - Customer Satisfaction Program. Certain vehicles may accumulate water in the rear compartment battery tub. This could occur from leaving a deck lid open in inclement weather, ice chest spillage, or water leak. Water intrusion into the DC/DC converter, which is located in the battery tub, could damage it. This corrective action will provide an exit path for water which entered the battery tub.Dealers are to install two drains in the battery tub to prevent accumulation of water.
N192210240
N192210240 - Special Coverage Adjustment - Certain vehicles shown above, may have a condition that could cause the evaporative emissions purge valve to not fully close. If this condition occurs, the engine could run rough, hesitate or stall at idle speeds. Additionally, the Malfunction Indicator Light (Check Engine Light) would illuminate and a diagnostic trouble code would be set. This special coverage covers the condition described above for a period of 10 years or 150,000 miles (240,000 km) for Acadia, Cascada, Enclave, Traverse, vehicles or 10 years or 120,000 miles (193,000 km) for Caprice, Cruze, Encore, Impala, LaCrosse, Sonic and Trax vehicles, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to replace the evaporative emissions purge valve as necessary. The repairs will be made at no charge to the customer.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PI0592E
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
130089008B
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
080730026F
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PIT5698
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIC5779K
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
19NA081
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some SiriusXM Channels Due to Interference in Some Geographic Locations.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
N192210230
N192210230 - Special Coverage - Some 2015-2016 Chevrolet Cruze and 2015 Chevrolet Sonic vehicles equipped with a 1.4L engine may have a condition where cracks can develop in the diaphragm of the Positive Crankcase Ventilation (PCV) pressure regulator valve. This valve is a part of the engine camshaft cover. If this were to occur, excess air could be drawn into the engine intake. As a result, the engine may run rough, especially during idle, the Malfunction Indicator Light (Check Engine Light) would illuminate and a diagnostic trouble code for Fuel Trim Lean (P0171) or other airflow related DTC would set. Dealers are to replace the engine camshaft cover as necessary. The repairs will be made at no charge to the customer.
17NA045
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
1308116001E
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
000601012J
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
PIP5657A
This Preliminary information communicates the possibility of a misfire occuring due to a broken center insulator on the spark plug.
PIP4670G
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
060847001O
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP5657
This Preliminary information communicates the possibility of a misfire occuring due to a broken center insulator on the spark plug.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
PIC6206C
This Preliminary Information communication provides information to the technician the step on diagnosing and repairing vehicles with inoperative Air conditioning, Instrument Cluster, OnStar, or other various electrical concerns. Technician may also find that fuses F35DA, F36DA, or the F37DA in the X51A Instrument Panel Fuse Block may not be powered up. Gain access to connector X201 and inspect connector for being properly aligned and the locking lever fully locked into place. Fully lock the connector and retest.
19NA114
This informational bulletin provides information to the tech to test the PCV for proper performance before replacing the camshaft cover to correct a MIL On w/DTC P0171.
PIP5647
This Preliminary information communicates A vehicle may have a concern of running poor and stalling. No trouble codes may be set referencing this condition. Fuel trims around -20% may be observed on both banks. Engine oil level will be found over full and have a fuel odor. It will be found that the Engine oil is diluted with fuel. Small gas engines (SGE) May only have the engine oil level over full and have a fuel odor. It will be found that the Engine oil is diluted with fuel. This concern is caused by marshalling the vehicle around the lot before it is sold and/or short driver cycles.
000310006N
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
19NA101
This technical bulletin provides a procedure to replace the intake manifold if diagnostics has found the Non Return Valve missing.
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5495J
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
19NA090
This informational bulletin explains to the technician to inspect the pistons for damage and not just replace the engine assembly if the pistons are the only cause of damage.
PIP5569A
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIC6360
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
030729004L
This informational bulletin provides normal operating characteristics and diagnostic information on Manual transmissions.
N172097060
N172097060 - Special Coverage Adjustment. Certain vehicles may have a condition where the Side Blind Zone Alert (SBZA) modules may fail or malfunction due to water intrusion. The driver may experience a side blind zone alert message displayed on the driver instrument cluster (DIC). If this message is ignored, the condition could result in the corruption of LS GMLAN that may result in the loss of some driver interface functions such as cluster, infotainment / displays, chime, and passenger presence detection (passenger airbag could be suppressed, w/airbag TT, DIC message). Dealers are to repair the vehicle by ordering and installing the appropriate service kit. The service kit will contain all of the components required to complete the repair. The repairs will be made at no charge to the customer.
PIP4670F
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
030603004Y
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
070849020P
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
1008110001G
This informational bulletin provides information on proper use of floor mats.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP5632
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
110849001Z
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
PIP5472F
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised to first perform the SI diagnostic. That if the diagnostic fails to isolate the concern, then replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIT4945H
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
010310003R
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
15NA087
This technical bulletin advises the technician to rest the MIL and diagnose additional DTCs for why the code is setting and disabling the start/stop system.
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
110849001Y
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
PIT5444D
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
030603004X
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
18NA335
This informational bulletin provides to the technician the correct parts and the labor operation number in conjunction with the repair.
060089026O
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
PIC5650F
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
17NA066
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow test.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIC6267A
This Preliminary information communicates that some customers my comment on a constant horn and/or that the horn is to sensitive. The horn contacts and may not be properly seated on the horn pads. Inspect horn contacts and wiring for proper routing and correct as necessary.
18NA153
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if vehicles apply within the settings.
PIP5598A
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
000310003X
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
060847001N
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP5197L
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIP5197K
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5495H
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found. The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis to perform, prior to replacing and returning a turbocharger to the WPC.
PIE0475A
This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
PIP5197J
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
PIP5601
This Preliminary information communicates
PIP5353E
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
PIP5197H
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
PIP5495G
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIT4945G
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle. Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5598
This Preliminary information communicates the possibility of a crank no start or extended crank condition due to exhaust cam reluctor being out of position.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP5241B
This Preliminary Information communication provides information to the technician about improper engine block cleaning during engine block service could lead to lines in the block deck surface that may be mistaken for cracks. Technician using improper block deck cleaning methods may see lines in the block deck surface. These lines are the result of using abrasive pad bristle devices to clean the gasket surface of the engine components. Technician should use the latest version of bulletin 00-06-01-012 for complete details on the use of these devices.
PIP5495E
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5472E
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised to first perform the SI diagnostic. That if the diagnostic fails to isolate the concern, then replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
PIC5779J
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5370D
This Preliminary Information communication provides information to the technician that some vehicle may have an “Exhaust Fluid Quality Poor” on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
PIP5151F
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.
PIP5558C
This Preliminary information communicates a possible cause of the clutch pedal slow to return.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIP5558B
This Preliminary information communicates a possible cause of the clutch pedal slow to return.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5370C
This Preliminary Information communication provides information to the technician that some vehicle may have an “Exhaust Fluid Quality Poor” on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
PIP5151E
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5373B
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIP5569
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
PIP5519A
This Preliminary information communicates the possibility of the timing chain tesnioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE.
PIP5353D
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
18NA141
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
150603002M
This bulletin provides information on approved warranty part numbers for original equipment batteries.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
18NA125
This informational bulletin provides information for engine oil life monitor operation calculation.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
080730035C
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
150603002L
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
130089010B
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance Claim (PAC) within the Courtesy Transportation Assistance Program.
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
110849001W
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
010310003Q
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
PIP5197G
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
110089002C
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
PIP5490D
This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Code P0300 set. The technician will need to perform engine compression and leakage Testing in Service Information. If excessive leakage to the crankcase is isolated, the technicain is directed to check the condition of all cylinder walls.If the cylinder wall surface has not been damaged, the technician is directed to replace all four pistons.
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
PIP5558A
This Preliminary information communicates a possible cause of the clutch pedal slow to return. Gives a technician direction to assist in diagnosis.
PIE0455
This engineering information bulletin is requesting information from the field on vehicles that have the condition of Malfunction Indicator Illuminated with DTC P0446 Set.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
PIP5558
This Preliminary information communicates a possible cause of the clutch pedal slow to return. Gives a technician direction to assist in diagnosis.
090604015C
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PI0725B
This PI provides information to the technician that this is a normal condition and advises not to replace the engine for this reason.
PIP4670E
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
16NA316
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of the internals.
030603004W
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
150603002K
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
150603001D
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
18NA027
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5495D
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
100864002D
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is considered warranty and non-warranty.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
060089026N
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
010310003P
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIP5472D
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised to first perform the SI diagnostic. That if the diagnostic fails to isolate the concern, then replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
17NA074
This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or Apple CarPlay.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
PIC5650D
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIC5491K
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
PIC6287A
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIT5354B
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
16NA075
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving Speeds
000310003W
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
080730026E
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
PIP5472C
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised that if the engine misfires during very specific cold start conditions, to replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
120089007A
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
150603001C
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
16NA327
This technical bulletin provides a procedure for securing unused front speaker clinch nuts to correct a customer concern of a rattle or buzz noise from the IP when vehicle is driven on rough or dirt roads.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIP5417B
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. The technician is directed to perform the testing and to check related components based on the results.
150603002J
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
16NA239
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
17NA385
This technical bulletin provides a procedure to reprogram the ECM to correct a condition of When Accelerating and/or Coming to a Stop at Low Speed, Speedometer May Suddenly Jump and/or Radio Volume May Suddenly Increase if Speed Compensated Volume Feature is Enabled due to a calibration concern.
17NA386
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
150603002I
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
010601011J
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
PI1149A
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
PIC6235A
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
17NA142
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
040730013D
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
16NA158
This bulletin describes the Dealer special tool loan program process.
17NA375
This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or pixelated
PIT5119F
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
070604019F
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
17NA361
This technical bulletin provides a procedure to repair a pinched IP harness to correct the codes set.
PIP5418A
This Preliminary Information is to assist in the isolation of a rattle noise from the turbocharger wastegate actuator rod.
PIC3100F
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
17NA155
This technical bulletin provides a procedure to reprogram the ECM before having to replace O2 sensor.
17NA337
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
PIP5490C
This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Code P0300 set. The technician will need to perform engine compression and leakage Testing in Service Information. If excessive leakage to the crankcase is isolated, the technicain is directed to check the condition of all cylinder walls.If the cylinder wall surface has not been damaged, the technician is directed to replace all four pistons.
PIP5495C
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIP5517A
This Preliminary information communicates the following to the dealer. If an engine oil leak has been isolated to the front crankshaft seal, check for misfires low engine compression and/or cylinder leakage readings. These issues could cause excessive positive crankcase pressure leading to engine oil leaks.
16NA396
This technical bulletin provides a procedure to replace the RCDLR for vehicles with multiple concerns regarding the door remote controls and TPM sensors due to an internal concern within the RCDLR.
PIC5650C
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
17NA320
This informational bulletin provides information for dealers/technicians on an outside door handle or lock cylinder cover being loose, or falling off.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
IPC Odometer Programming Method Quick Reference Guide
140089004D
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
150603002H
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
16-NA-175
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
16-NA-396
Intermittent Operation of Key Fobs, Door Unlock Inoperative No Remote Detected Message with Possible TPM MIL Some customers may comment on intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. This may be accompanied with a No Remote Detected message on the DIC. Other symptoms may include: Passive Locking system locking keys in vehicle Push button start system failure to respond (cannot start or stop) with no remote detected message Passive entry system not responding to Lock/Unlock commands System not responding to active FOB key press lock, unlock, hatch/trunk, remote start and panic all inoperative Tire pressure monitor indicator illuminated with DTC's C0750, C0755, C0760 and C0765 with Symptom :29 Too Few Pulses. Cause This may be due to issues internal to the Remote Control Door Lock Receiver.
17-NA-155
Malfunction Indicator Lamp (MIL) Illuminated - DTC P015B Set Condition-Some customers may comment that the MIL is illuminated. The technician may find DTC P015B set. Cause This condition may be caused by the Engine Control Module (ECM) calibration too sensitive in setting DTC P015B. Correction-Note: Do Not replace the O2 sensor until the latest ECM calibration has been validated. Validate the ECM has the latest software calibration: If the ECM is not at the latest calibration, it must be reprogrammed to the latest software calibration available. If the ECM has the latest calibrations, refer to SI for the DTC set.
17-NA-320
Condition Information on Outside Door Handle or Lock Cylinder Cover Loose, Falling Off Some customers may comment on any of the following: Outside door handle loose. Outside door handle pulls out of door. Outside door handle fell off. Outside door handle lock cylinder cover fell off. Outside door handle lock cylinder cover loose. Cause The cause of the condition may be either of the following issues: 1. Door handle bracket fracture due to the door lock cylinder cover assembly not being fully seated during assembly. 2. Fastener not being torqued to proper specification.
17-NA-337
All or Some Options May Be Missing from Driver Information Center (DIC) Info Pages Menu Due to Them Not Being Selected Condition Some customers may comment that with the Info option selected from the main menu (1), the Info Pages are blank (2) when scrolling up and down. If information is present when scrolling up and down, they may also comment that certain items are missing when compared to other like vehicles Cause This condition may be caused when all/some of the options not being selected in the active info pages menu. Correction If this concern is encountered, determine if all/any of the selections in the active info pages menu are not selected. To do this, follow the steps listed below.
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
030603004V
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5151D
This Preliminary Information communication provides information to the technician about vehicles that may have a hard start, no start, rough running, or low fuel pressure. Technician may find Diagnostic Trouble Codes P0087, P0088, P0191 and P128E during the inspection. If during the inspection of the fuel system contamination is found the complete fuel system will need to be cleaned and flushed. After the fuel system is cleaned out test the fuel using the latest version of PIT3173.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
PIP5519
This Preliminary information communicates the possibility of the timing chain tensioner gasket being improperly installed or mis-positioned after major engine repairs causing a low engine oil pressure and dtc p06DE.
000601012H
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
PIP5517
This Preliminary information communicates the following to the dealer. If an engine oil leak has been isolated to the front crankshaft seal, check for misfires low engine compression and/or cylinder leakage readings. These issues could cause excessive positive crankcase pressure leading to engine oil leaks.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
150603002G
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PIC6185A
This Preliminary Information communication provides information to the technician with a diagnostic tip for navigation radios that have inaccurate entries at times when using the voice recognition to input the address. When using the Navigation command "Address" or "Destination" this Allows an address to be stated as a one-shot method. When using the Navigation command "Directed Address" this Allows an address to be stated one step at a time. Directed address option may be a better choice for entering that address.
PIP5370B
This Preliminary Information communication provides information to the technician that some vehicle may have an “ Exhaust Fluid Quality Poor ” on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
16-NA-380
This Technical bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of excessive soot from the tailpipe.
13-08-116-001C
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5197F
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
17-NA-211
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical connections that may set a DTC instead of just replacing a part.
PIT5119E
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIT5119E (1)
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
PIP5329C
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0341 and or P0366 set. If theconcern is duplicated, the technician is directed toreplace the related Camshaft Position sensor and retest for the code. If the Diagnostic Trouble Code returns technician should check the history to see if the vehicle was in a collision. If the vehicle has been in a collision, the technician is advised onrepair direction.
04-00-89-015Q
This warranty administration bulletin provide policy information on required operating procedures.
08-08-44-029H
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
17-NA-184
This informational bulletin provides information for dealers and technicians about the 1.4L turbocharged engine use two different suppliers for the oil filter housing which results in two different filters being used.
04-00-89-015P
This warranty administration bulletin provide policy information on required operating procedures.
11-08-49-001V
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
PI0686G
This bulletin provides a procedure to adding new brackets and repairing the front seats to correct the seats excessive movements.
17-NA-242
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
PIT5444C
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
10-00-89-005F
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required additional information.
16-NA-053
This 2016 Chevrolet Cruze New Model Features informational Bulletin provides various general information topics to the Service, Parts and Sales Personnel in order to familiarize them with the vehicle. It has been revised to create 16-NA-053 Version 4 by adding a Section for: Engine STOP/START information RPO KL9, with a graphic and system operation information. Also to remove the Attention statement and replace that information with a Table for: Region Countries United States and Canada.
16-NA-160
This informational bulletin provides information on wet resicaused by or staining on bottom of brake calipers that has no effect on brake operation.
16-NA-162
This informational bulletin provides information on a noise that is considered normal operation for customer concerns on a zipper type noise heard when turning the steering wheel caused by the interface between the electric steering motor and drive belt assembly.
16-NA-163
This informational bulletin provides information on wiper arms that have a pedestrian protection system and the potential for the system to be inadvertently tripped.
16-NA-238
This technical bulletin provides a procedure to reprogram the radio using SPS to correct the conditons of a Check DAB message or DAB re-routing message displayed after a recent reprogramming of the radio has been performed.
17-NA-233
This technical bulletin provides a procedure to install a boot around the evap filter pipe to avoid water enter the system causing the MIL to turn on.
PI1385A
This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are installed on the vehicle.
PIP5507B
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
16-NA-224
This informational bulletin provides information to inspect the wiring harness for pinched or backed out wires causing the back up camera not to work or lines across the screen.
PI1520C
This preliminary informational bulletin provides information regarding the need to relearn the auto/start and stop feature on vehicles equipped after a repair has been completed on the vehicle.
PIC5779H
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
15-06-04-004A
This technical bulletin provides repair information for a fuel leak at injector to fuel rail connection, to correct a customer concern of smelling a fuel odor.
PIC5611E
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5507A
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIP5507
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC6221A
This Preliminary Information communication provides information to the technician about vehicle that will have no XM audio or no signal. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIC6287
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIP5495B
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5495A
This Preliminary Information communication provides information to the technician about vehicles that may have a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Codes P0299 or P0234 set. The technician is provided with a list of causes of misdiagnosis leading to returned Turbochargers with no trouble found.The purpose of this information is to reduce the number of no trouble found (NTF) turbochargers being returned to the WPC by informing the Service Department personnel of what inspections and/or diagnosis toperform, prior to replacing and returning a turbocharger to the WPC.
PIP5490B
This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. The technician may find Diagnostic Trouble Code P0300 set. The technician will need to perform engine compression and leakage Testing in Service Information. If excessive leakage to the crankcase is isolated, the technicain is directed to check the condition of all cylinder walls.If the cylinder wall surface has not been damaged, the technician is directed to replace all four pistons.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
16-NA-316
This technical bulletin provides a procedure to drill two holes in the rear axle housings to spray lubricant into and then close up with rivets to correct a condition of a rear axle creak noise due to the improper lubrication of some of the internals.
17-NA-175
This technical bulletin provides a procedure to check the wiring harness to the crank sensor and validate and signs of rubbing or chaffing, repair wiring if found.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
03-00-89-006N
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
04-00-89-015O
This warranty administration bulletin provide policy information on required operating procedures.
16-NA-367
This informational bulletin explains the need to change the oil used in the LFV, LE2 engines, to a dexos 1 full synthetic to avoid piston damage.
PI1520D
This preliminary information advises the technician to perform a battery sensor module learn if the battery has been disconnected.
17-NA-142
This informational bulletin provides information on Wireless Charging Module Diagnosis.
PIP5490A
This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to perform an Engine Compression Testing in Service Information. If excessive leakage to the crankcase is isolated, check piston and cylinder wall condition. Technician should perform the repair per the level of damage. If the cylinder wall surface has not been compromised, only piston replacement is required.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
PIP5329B
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0341 and or P0366 set. If the technician has duplicated the concern replace the related Camshaft Position sensor and retest for the code. If the Diagnostic Trouble Code returns technician should check the history to see if the vehicle was in a collision. If the vehicle has been in a collision technician should call General Motors Technical Assistance Center.
GCUS-3-914
16147 01 - Customer Satisfaction Program. On certain vehicles, the center high mount stop lamp (CHMSL) fasteners may back off over time and cause a water leak, allowing water to flow into the rear compartment battery tub. When the battery tub fills with water to a height of 50mm or more, the DC/DC converter module board and connector are exposed to water which may cause corrosion. If water drains below the DC/DC converter, a resistive short may occur on the printed circuit board which could result in an unattended fire when the DC/DC converter is powered. Dealers are to inspect for water damage in the battery tub electrical components, and replace the CHSML gaskets and nuts.
16-NA-110
This bulletin provides information for customers that may comment on noise or feel of accelerator pedal when depressed This is considered normal operation because there is a wide open throttle detent switch that provides feedback when full accelerator travel is reached
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
16-NA-355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
17-NA-074
This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or Apple Carplay.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
03-06-03-004U
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
15-06-03-002F
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PI1411A
This preliminary informational bulletin provides a diagnostic tip for technicians who may find an oil leak after a recent oil change has been performed.
PIP5197E
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
PIP5490
This Preliminary Information communication provides information to the technician about vehicles that may be running rough with a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Code P0300 set. Technician will need to perform an Engine Compression Testing in Service Information. If excessive leakage to the crankcase is isolated, check piston and cylinder wall condition. Technician should perform the repair per the level of damage. If the cylinder wall surface has not been compromised, only piston replacement is required.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
PIE0386A
This engineering information bulletin ends the need for information from the field on vehicles that have the condition of A/C Inoperative and/or Abnormal Noises When A/C is Turned On.
16-NA-007
This technical bulletin provides a procedure for reprogramming power steering control module due to a notchy or stick/slip feeling in the steering wheel near the center position.
PIE0384A
This engineering information bulletin ends the need for information from the field on vehicles that have the concern of constant horn and/or any horn related concerns.
PI0671A
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid reservoir.
PIC6267
This Preliminary information communicates that some customers my comment on a constant horn and/or that the horn is to sensitive. The horn contacts and may not be properly seated on the horn pads. Inspect horn contacts and wiring for proper routing and correct as necessary.
PIP5417A
This Preliminary Information communication provides information to the technician related to utilizing crankcase pressure testing to aid in engine oil leak diagnostics. The technician is directed to perform the testing and to check related components based on the results.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
06-08-47-001M
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
10-00-89-006F
This informational bulletin provides information for dealers how to submit a product information report.
12-09-41-002D
This informational bulletin explains not to put anything metal or conductive on the passenger seat or it may set the reminder chime off.
GCUS-9-3638
Dessicated Air Bag Inflator Study - Used Vehicle Inventory Only. The 2016 model year Chevrolet Cruze Limited has been added to this engineering study. The attached instruction sheet has been updated accordingly. Please discard previous instructions. The list of eligible vehicles also attached to this message contains 2016 Chevrolet Cruze Limited vehicles that have been identified as currently being in used vehicle inventory. The list has also been updated for the other involved vehicles. Since used vehicle inventory can change daily, all participating dealers should check their used vehicle inventory frequently for applicable candidates and proceed accordingly. Please ensure that all used air bag inflators are returned as soon as possible to GM for analysis.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIP5472A
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised that if the engine misfires during very specific cold start conditions, to replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4990D
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on. Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
PIP5353C
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
GCUS-3-848
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5959C
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
17-NA-045
This informational bulletin provides Information on Using Voice Pass-Thru to Access Voice Recognition Commands on Cell Phone and how it does not work on models equipped with IOA and IOB radios.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5197D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have excessive oil consumption, blue smoke from the exhaust, or a Malfunction Indicator Lamp. Technician should inspect the PVC orifice for leaking oil or drawing a vacuum at idle. If the PCV orifice external port is leaking oil or vacuum, replace the camshaft cover assembly. Technician will inspect for a missing intake manifold Non Return Valve that may have damaged the PCV orifice diaphragm. Check for the return valve if it is not visible use a long cotton swab to wipe any excess oil from the valve to validate. If the non return valve is still not visible, then intake manifold removal for inspection is required to validate. When the valve is present reinstall the intake manifold. When the valve is not present replace the intake manifold assembly.
02-00-89-002Q
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
PIC6223A
This Preliminary Information communication advises the technician that the Rear Axle is no longer on restriction.
01-03-10-003O
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
PIC6049F
This Preliminary Information communicationends thewireless charging module restriction through the General Motors Technical Assistance Center.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP4902J
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
17-NA-034
This informational bulletin provides information to the customer that the auto stop system not working is a normal characteristic and no parts should be replaced for this condition.
PIP5472
This Preliminary Information communication provides information to the technician related to vehicles that have a Malfunction Indicator Lamp on. A technician may find Diagnostic Trouble Code P050D set as current or history. The technician is advised that if the engine misfires during very specific cold start conditions, to replace only the exhaust side SHLA's (Stationary Hydraulic Lash Adjuster) and to retest for the concern.
17-NA-024
This technical bulletin provides a procedure to turn the audible feedback option on and off in the radio settings to prevent an audible beep will occur when scrolling from page 1 to page 2 of the OnStar menu, which may be interpreted as a hands free OnStar call request.
PIP5329A
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0341 and or P0366 set. If the technician has duplicated the concern replace the related Camshaft Position sensor and retest for the code. If the Diagnostic Trouble Code returns technician should check the history to see if the vehicle was in a collision. If the vehicle has been in a collision technician should call General Motors Technical Assistance Center.
15-06-03-002E
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
PI1166D
This preliminary information bulletin provides a information on vehicles that are slow to heat up in cold temperatures.
PIE0389A
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition of Rough Running Engine with Malfunction Indicator Lamp On and DTC P0300 Set.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
11-08-49-001U
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
GCUS-3-813
39570 - SUB - The image processor within the front camera module (FCM) may reset and be offline for 25-35 seconds. During this period, features reliant upon the camera information will respond to the last known data for 25-35 sec. This may result in unwanted feature interventions during the condition, including lane keeping assist, a continuously issued warning or braking request. All system overrides continue to function per design. Reprogram front camera module (FCM).
PIE0372D
This engineering informational bulletin is ending the need for information from the field on vehicles that have the condition of vehicle difficult to shift or will not shift into gear.
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
99-00-89-019O
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
PIC6149A
This Preliminary Information communication provides information to the technician about an intermittent concern for Service KeylessStart message displayed in the Driver Information Center. Technician may find a Diagnostic Trouble Code B3124. Technician should inspect the trunk area for objects that may block the reception of the Rear Compartment Antenna. Technician will also inspect antenna for correct installation
PIC6216C
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
PIC6220A
This Preliminary Information communication provides information to the technician about vehicles with an intermittent loss of gridlines in the rear camera display screen and a "Service Rear Vision System" message that both happen at the same time. Technician should check for Diagnostic Trouble Codes and follow published Service Information diagnostics for the Diagnostic Trouble Codes. If not Diagnostic Trouble Codes stored and the concern was duplicated or the customer described the concern, dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
07-08-49-020L
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIC6186F
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIE0378A
This engineering informational bulletin is ending the need for information from the field on vehicles that have the concern of Intermittent or Erratic Power Seat, Memory Seat Recall or Easy Exit Seat Recall Functions.
PIT5411G
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
16-NA-288
This technical bulletin provides a procedure for replacing both steering linkage inner tie rods to eliminate a rattle type noise coming from the front end over bumps.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
99-00-89-019N
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
GCUS-3-796
16147 Customer Satisfaction. On certain vehicles, the center high mount stop lamp (CHMSL) fasteners may back off over time and cause a water leak, allowing water to flow into the rear compartment battery tub. When the battery tub fills with water to a height of 50mm or more, the DC/DC converter module board and connector are exposed to water which may cause corrosion. If water drains below the DC/DC converter, a resistive short may occur on the printed circuit board which could result in an unattended fire when the DC/DC converter is powered. Dealers are to inspect for water damage in the battery tub electrical components, and replace the CHSML gaskets and nuts (adding Loctite to the nut).
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIC6235
This Preliminary Information communication provides information to the technician about vehicles that the navigation system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
01-03-10-003N
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
02-00-89-002P
This informational bulletin provides information for dealers/technicians on when and how to submit a field product report.
05-00-89-055F
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIC6233
This Preliminary Information communication provides information to the technician about vehicles that when an incoming Bluetooth call will ring through the vehicle system, but the call can only be answered by using the handset. Technician can update the radio using the latest version of 15-NA-081 if the vehicle is 2014 or newer. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
16-NA-397
This technical bulletin provides repair information to correct a customer concern of the front or rear side door glass/window being loose in the door, or will not move up or down.
16-NA-395
This informational bulletin provides information for technicians that upon removal of a front door trim panel, two high retention retainers will break but must be replaced with same high retention retainers to properly secure the door trim.
PIC6216B
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and re-pair any phones that were deleted.
PIT5354A
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
16-NA-308
This technical bulletin provides a preliminary service procedure to verify torque of the CHMSL fasteners when a water leak is evident at the roof/rear window area, or if water is found in the trunk.
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5353B
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
11-00-89-004B
This warranty administration bulletin provide policy information on the change in product field action customer reimbursement procedure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
16-NA-107
This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
11-08-49-001T
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
PIE0386
This engineering information bulletin is requesting information from the field on vehicles that have the condition of A/C Inoperative and/or Abnormal Noises When A/C is Turned On.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
04-06-04-051E
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
03-06-04-017J
This Informational Bulletin provides information on available Diesel Fuel Additives.
PIC6186E
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5353A
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
GCUS-9-3040
16018 - Special Coverage. A diagnostic trouble code P24AE, P24AF, P24C6 or P24C7 may set on some of these vehicles as a result of exhaust particulate sensor failure caused by either sensor contamination or sensor damage from humidity in the exhaust. If this condition occurs within the stated terms, dealer will replace the exhaust particulate sensor.
PIP5313C
This Preliminary Information communication advises the technician that the E80 Engine Control Module part numbers 12669908 or 12672502 have been placed on part restriction by General Motors Technical Assistance Center. Dealer will need to call General Motors Technical Assistance Center for further assistance.
040604051D
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
PIC6227
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent loss of Key Fob and/or Passive Entry, Passive Start functions. Vehicle also may have a ?No Remote Detected? message on the Driver Information Center. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIE0384
This engineering information bulletin is requesting information from the field on vehicles that have the concern of constant horn and/or any horn related concerns.
PIC6206A
This Preliminary Information communication provides information to the technician the step on diagnosing and repairing vehicles with inoperative Air conditioning, Instrument Cluster, OnStar, or other various electrical concerns. Technician may also find that fuses F35DA, F36DA, or the F37DA in the X51A Instrument Panel Fuse Block may not be powered up. Gain access to connector X201 and inspect connector for being properly aligned and the locking lever fully locked into place. Fully lock the connector and retest.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
150603002D
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
150603002C
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
15NA044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
16NA355
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
030604017J
This Bulletin has been Revised to add the 2017 Colorado, Cruze, Canyon, Chevrolet & GMC Light/Medium Duty Trucks. Please discard Corporate Bulletin Number 03-06-04-071I
PIC6216A
This Preliminary Information communication provides information to the technician about vehicles voice recognition inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
16NA308
This technical bulletin provides a preliminary service procedure to verify torque of the CHMSL fasteners when a water leak is evident at the roof/rear window area, or if water is found in the trunk.
030603004S
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
030603004T
Battery Testing and Warranty Replacement Requirements (North America ONLY)
040089015N
This warranty administration bulletin provide policy information on required operating procedures.
PIC6223
This Preliminary Information communication advises the technician that the Rear Axle part numbers 39059649, 39059651, and 39059652 was placed on restriction through the General Motors Product Quality Center. Dealer will need to contact General Motors Product Quality Center for further assistance.
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
PI0907C
This preliminary informational bulletin provides repair information to correct a customers concern of check engine light on with DTC P1101 set.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
140089004C
The information in this bulletin details the proper configurations for the ignition key, fob, key tags and key rings and applying a QR code sticker or barcode sticker to a key fob.
GCUS-3-708
16008 - Emission Recall. The ?Jiffy-Tite? fitting on the turbocharger oil feed pipe may not have been tightened to the specified torque. A fitting not tightened to specification may result in an engine oil leak. Continued driving with an oil leak at this location may result in low oil pressure and illumination of the malfunction indicator lamp. Dealers will inspect and replace the turbocharger oil feed pipe fitting.
PIC6186D
This Preliminary Information communication provides information to the technician about vehicles that the radio will turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIC6222
This Preliminary Information communication provides information to the technician about vehicles that may have a clock resetting to 12:00. Dealer should advise the customer General Motors is working on a solution to the concern.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
07-00-89-037J
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
08-08-44-029G
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIC6221
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLE THAT WILL HAVE NO XM AUDIO OR NO SIGNAL. DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS WORKING ON A SOLUTION FOR THIS CONCERN.
PIP5421
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY BE RUNNING ROUGH WITH A MALFUNCTION INDICATOR LAMP ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0300 SET. TECHNICIAN WILL NEED TO PERFORM AN ENGINE COMPRESSION TESTING IN SERVICE INFORMATION. IF EXCESSIVE LEAKAGE TO THE CRANKCASE IS ISOLATED, CHECK PISTON AND CYLINDER WALL CONDITION. TECHNICIAN SHOULD PERFORM THE REPAIR PER THE LEVEL OF DAMAGE. IF THE CYLINDER WALL SURFACE HAS NOT BEEN COMPROMISED, ONLY PISTON REPLACEMENT IS REQUIRED.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
16-NA-329
This technical bulletin provides a procedure to repair the GMLAN wiring harness to if found to be pinched behind the radio and correct the customers concern of a no start condition.
PIC6220
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH AN INTERMITTENT LOSS OF GRIDLINES IN THE REAR CAMERA DISPLAY SCREEN AND A "SERVICE REAR VISION SYSTEM" MESSAGE THAT BOTH HAPPEN AT THE SAME TIME. TECHNICIAN SHOULD CHECK FOR DIAGNOSTIC TROUBLE CODES AND FOLLOW PUBLISHED SERVICE INFORMATION DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODES. IF NOT DIAGNOSTIC TROUBLE CODES STORED AND THE CONCERN WAS DUPLICATED OR THE CUSTOMER DESCRIBED THE CONCERN, DEALER SHOULD COMMUNICATE TO THE CUSTOMER THAT WE APOLOGIZE FOR THIS INCONVENIENCE AND THAT GENERAL MOTORS IS CURRENTLY EVALUATING THIS CONCERN.
PIE0372C
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of vehicle difficult to shift or will not shift into gear.
16-NA-327
This technical bulletin provides a procedure for securing unused front speaker clinch nuts to correct a customer concern of a rattle or buzz noise from the IP when vehicle is driven on rough or dirt roads.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
08-08-44-015G
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
01-00-89-010L
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
15-NA-081
This technical bulletin provides a procedure to reprogram the radio to correct the conditions of Radio Locks Up and/or Resets, Bluetooth Pairing, IPhone Loses Pairing, Bluetooth Connection And Audio Concerns, Street Names Flickering, TBT Routing Screen Displayed After Download is Finished, XM Weather Alerts Cannot Be Selected Off, Voice Recognition and Navigation Updates, Various Rear Vision Camera Concerns, Podcast Will Not Play, Cannot Edit Device List due to an internal calibration concern.
PI0653D
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
07-08-49-020K
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
01-03-10-003L
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
PIC5491J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIT5384B
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.
PIC6073C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
PIC6216
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES VOICE RECOGNITION INOPERATIVE FOR CALLING BLUETOOTH PHONE CONTACTS. TECHNICIAN WILL NEED TO CLEAR ALL PRIVATE DATA AND REPAIR ANY PHONES THAT WERE DELETED.
16-NA-287
This informational bulletin provides information on a new service replacement radio has been released for the vehicles above. As a result, the radio part number received may not be the same part number as the one that was ordered. Certain service replacement radios do not require USB programming.
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
16NA241
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
16NA043
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.
16NA277
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE BCM TO CORRECT A CUSTOMER CONCERN OF INTERMITTENT LOSS OF KEY FOB AND/OR PASSIVE ENTRY, AND PASSIVE START FUNCTIONS DUE TO THE REMOTE CONTROL DOOR LOCK RECEIVER (RCDLR) BECOMING CAN LOCKED-UP AND UNRESPONSIVE DUE TO MULTIPLE SIGNALS BEING RECEIVED IN A SPECIFIC TIME SPAN.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PIT5411F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
16NA269
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE HVAC MODULE TO CORRECT THE CUSTOMERS CONCERN OF POOR A/C PERFORMANCE DURING STOP/START.
PIP5417
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT HAVE AN OIL LEAK AT THE REAR OF THE ENGINE. TECHNICIAN WILL NEED TO USE THE EVAPORATIVE EMISSIONS SYSTEM TESTER TO RECORD THE CRANKCASE PRESSURE. IF THE CRANKCASE PRESSURE IS IN THE PROPER RANGE, FOLLOW PUBLISHED SERVICE INFORMATION STRATEGY BASED DIAGNOSTICS FOR ENGINE OIL LEAKS. IF THE CRANKCASE PRESSURE IS EXCESSIVELY POSITIVE OR NEGATIVE, INSPECT FOR ANY AIR INDUCTION RESTRICTIONS IN THE FRONT AIR INTAKE DUCT TO AIR CLEANER HOUSING OR IN THE AIR CLEANER HOUSING. TECHNICIAN SHOULD ALSO INSPECT THE AIR CLEANER OUTLET DUCT FOR A BLOCKED POSITIVE CRANKCASE VENTILATION FRESH AIR-PORT. IF THE PORT IS NOT BLOCKED, THEN REPLACE THE CAMSHAFT COVER ASSEMBLY AND RETEST FOR PROPER CRANKCASE PRESSURE.
PIP5418
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES WITH A RATTLE NOISE FROM ENGINE AREA WHILE DRIVING. TECHNICIAN WILL NEED TO CHECK THE TORQUE ON TURBOCHARGER MOUNTING BOLTS. IF THE TURBOCHARGER TORQUE IS CORRECT AND APPLY A SMALL AMOUNT OF PRESSURE TO THE WASTEGATE ROD USING A SUITABLE TOOL WHILE THE CONDITION IS PRESENT CORRECTS THE CONCERN, DO NOT REPLACE ANY COMPONENTS AT THIS TIME AS GENERAL MOTORS POWERTRAIN IS AWARE OF THIS CONDITION AND REVIEWING OPTIONS.
PIC6212
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR VEHICLES THAT STALLED WHILE DRIVING AND OR WILL NOT CRANK OVER AND OR THE BATTERY LIGHT OR SERVICE CHARGING SYSTEM MESSAGE BEING ON. TECHNICIAN MAY FIND DIAGNOSTIC TROUBLE CODE P0622 SET. TECHNICIAN SHOULD INSPECT THE MAIN ENGINE GROUND CABLE LOCATED UNDERNEATH THE STARTER MOTOR FOR BEING LOOSE, IF THE CABLE IS FOUND LOOSE REPAIR AS NECESSARY.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIE0365A
THIS ENGINEERING INFORMATIONAL BULLETIN IS ENDING THE NEED FOR INFORMATION FROM THE FIELD OF VEHICLES WITH THE CONDITION OF USB PORT INOPERATIVE.
PIP4786C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE. TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
030603004R
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
GCUS-3-651
50120 01 - Customer Satisfaction (service procedure revised). Certain vehicles may have a condition in which the bolt attaching the positive battery cable to the rear fuse block may not be properly attached. This condition may prevent the vehicle from being started, or may illuminate the service engine soon light. Dealers will inspect the battery positive cable bolt and, if necessary, replace the bolt or fuse block.
GCUS-9-2629
38170 - Special Coverage. The accelerator pedal can break at the stalk just below the housing due to the driver entering or exiting the vehicle with their foot resting on the accelerator pedal. If the pedal breaks, it would not be possible to operate the accelerator once the stalk has broken off. The vehicle would return to idle regardless of transmission gear position. If this condition occurs within the stated terms dealers will replace the accelerator pedal.
GCUS-3-650
50120 - Customer Satisfaction. Certain vehicles may have a condition in which the bolt attaching the positive battery cable to the rear fuse block may not be properly attached. This condition may prevent the vehicle from being started, or may illuminate the service engine soon light. Dealers will inspect the battery positive cable bolt and, if necessary, replace the bolt or fuse block.
140089004B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IGNITION KEY, FOB, KEY TAGS AND KEY RINGS CONFIGURATION FOR VARIOUS VEHICLES AND APPLYING A QR CODE STICKER OR BARCODE STICKER TO THE FOB.
16NA249
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS LESS THAN 10,000 MILES ON IT.
PIE0372B
THIS ENGINEERING INFORMATIONAL BULLETIN IS REQUESTING INFORMATION FROM THE FIELD ON VEHICLES THAT EXHIBIT THE CONDITION OF HARD TO SHIFT OR GET INTO GEAR.
PIP5373A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
16NA246
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET.
000601012F
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
16NA242
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT.
000601026I
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL ENGINE DAMAGE.
PIE0372A
This engineering informational bulletin is requesting information from the field on vehicles that exhibit the condition of hard to shift or get into gear.
PIE0372
This engineering informational bulletin is requesting information from the field on vehicles that exhibit the condition of hard to shift or get into gear.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
16-NA-219
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE HMI MODULE TO CORRECT A CONDITION OF GPS INOPERATIVE, RED LINE ACROSS GPS INDICATOR OR THE LOCATION IS STUCK IN WARREN MICHIGAN.
PIP5376A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE ENGINE EXCHANGE PROGRAM ON VEHICLES EQUIPPED WITH ENGINE REGULAR PRODUCTION OPTION CODE LE2 HAS ENDED. THIS ENGINE CAN NOW BE ORDERED THROUGH THE REGULAR GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS PROCESS OR PRODUCT QUALITY CENTER PROCESS FOR REQUIRED DEALERS.
PI1237B
THIIS INFORMATION BULLETIN PROVIDES INFORMATION ON HOW THE EXHAUST AND INTAKE CAMSHAFT POSITION EXCITER WHEEL MUST BE INSTALLED PROPERLY TO PREVENT A CUSTOMER CONCERN ON AN INTERMITTENT CRANK/NO START.
PIC4788G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN OF DIAGNOSTIC INSTRUCTIONS TO TAKE WHEN THE KEY WILL NOT FOLD INTO THE FOB OR WILL NOT STAY IN THE FOLDED POSITION. THE TECHNICIAN MAY COMMENT THAT THE KEY IN THE FOB WILL NOT FOLD CLOSE OR STAY LATCHED CLOSED. DAMAGE TO THE FOLDING MECHANISM COULD RESULT FROM STORING THE KEY IN THE DOOR LOCK CYLINDER AND ACCIDENTLY BUMPING OR MAKING CONTACT WITH THE KEY FOB. PLEASE ADVISE ALL DEALER PERSONNEL TO REFRAIN FROM STORING THE KEY IN THE DOOR LOCK EVEN FOR BRIEF PERIODS.
PI1521B
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPLACE THE POWER STEERING FUSE FOR A CONDITION OF LOSS OF POWER STEERING ASSIST AND/OR SERVICE POWER STEERING MESSAGE DISPLAYED.
PIP5094A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
10-08-110-001E
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.
04-00-89-015M
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES POLICY INFORMATION ON USING GM SERVICE POLICIES AND PROCEDURE MANUAL THAT REPRESENT KEY GM REQUIREMENTS FOR SERVICE OPERATIONS.
38240
38240 - SERVICE UPDATE. CERTAIN VEHICLES, EQUIPPED WITH MANUAL SEAT ADJUSTERS MAY HAVE BEEN BUILT WITH SEAT TRACKS THAT HAVE AN IMPROPERLY INSTALLED TRACK LOCK ON EITHER THE INBOARD OR OUTBOARD SIDE. A PIN THAT RETAINS THE TRACK LOCK TO TRACK RAIL MAY BE MISSING OR DAMAGED ALLOWING THE TRACK LOCK TO FALL OUT OF POSITION. VEHICLES WITH THIS CONDITION MAY EXPERIENCE DIFFICULTY TO UNLOCK AND MOVE THE MANUAL SEAT HORIZONTAL ADJUSTMENT OR MAY EXHIBIT LOOSENESS OR BINDING IN THE SEAT TRACK. DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE DRIVER AND/OR PASSENGER FRONT SEAT ADJUSTER.
PIP5398A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN UPPER OIL PAN AND LOWER OIL PAN PRODUCT QUALITY CENTER PART RESTRICTION HAS ENDED. THESE PARTS CAN NOW BE ORDERED THROUGH THE REGULAR GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS PROCESS OR PRODUCT QUALITY CENTER PROCESS FOR REQUIRED DEALERS.
09-06-04-026M
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
PI1520B
This informational bulletin provides information on the need to perform a Battery Sensor Module learn procedure after a stop/start system repair or after any repair where the 12V battery negative cable has been disconnected.
PIC-5779-G
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH INFORMATION ON THE PROPER WASHING OF THE BRIGHT ALUMINUM MOLDINGS TO AVOID THE MOLDINGS FROM GETTING DAMAGED. IT IS RECOMMENDED THAT A NON-ALKALINE SOLUTION BE USED FOR PREPARATION & WASHING OF THE BRIGHT ALUMINUM MOLDINGS.
99-08-51-007G
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
16-NA-108
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of buzz or static noise from radio audio speakers, android auto connection issues, intermittent black screen or Sirius XM reverts to XM1 channel intermittently caused by to the current software calibration within the radio.
GCUS-3-563
46000 - Customer Satisfaction Program. Certain 2016 Chevrolet Cruze vehicles may have a loose connection at the battery negative terminal to ground stud. This condition may cause the engine to stall while driving, may prevent the vehicle from being started, or may illuminate the service engine soon light. Dealers will add a washer to the negative ground.
PIC-6095-A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH A DIAGNOSTIC AID FOR IDENTIFYING INFOTAINMENT COMPONENTS ON THE VEHICLES TO ENSURE THAT THE CORRECT COMPONENT IS ORDERED OR REPLACED AND THE CORRECT LABOR CODE IS USED FOR WARRANTY SUBMISSION.
PI0592D
This informational bulletin provides information on service programming system (SPS) errors.
PIC-6205
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO REPLACE THE RADIO IF THE PHONE ICON IS PRESSED AND IT WILL HIGHLIGHT, OR HIGHLIGHT AND SPIN, BUT THE RADIO WILL NOT CHANGE FROM THAT SCREEN.
PIC-6206
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEP ON DIAGNOSING AND REPAIRING VEHICLES WITH INOPERATIVE AIR CONDITIONING, INSTRUMENT CLUSTER, ONSTAR, OR OTHER VARIOUS ELECTRICAL CONCERNS. TECHNICIAN MAY ALSO FIND THAT FUSES F35DA, F35DA, OR THE F37DA IN THE X51A INSTRUMENT PANEL FUSE BLOCK MAY NOT BE POWERED UP. GAIN ACCESS TO CONNECTOR X201 AND INSPECT CONNECTOR FOR BEING PROPERLY ALIGNED AND THE LOCKING LEVER FULLY LOCKED INTO PLACE. FULLY LOCK THE CONNECTOR AND RETEST.
PIE0365
This engineering information bulletin is requesting information from the dealers on a customer concern that one of the USB ports is not charging, allowing data to transfer.
12-08-132-001D
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.
PIP-5313-B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE E80 ENGINE CONTROL MODULE PART NUMBERS 12669908 OR 12672502 HAVE BEEN PLACED ON PART RESTRICTION BY GENERAL MOTORS TECHNICAL ASSISTANCE. DEALER WILL NEED TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
PIP-5398
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE UPPER AND LOWER OIL PAN WILL BE PLACED ON PRODUCT QUALITY CENTER PART RESTRICTION. DEALER WILL NEED TO CALL GENERAL MOTORS PRODUCT QUALITY CENTER FOR ASSISTANCE.
16-NA-150
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO RETROFIT THE VEHICLES REMOTE KEYLESS SYSTEM TO CORRECT A CUSTOMER CONCERN ON THE RKE TRANSMITTER RANGE OF THE REMOTE START FUNCTION BEING TOO SHORT CAUSED BY ELECTRICAL INTERFERENCE, WHICH MAY DEGRADE THE REMOTE SIGNAL AND SHORTEN THE RANGE.
SB-02-07-30-029Z
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE PRODUCT QUALITY CENTER (PQC) ASSEMBLY REPLACEMENT PROCESS.
SB-16-NA-138
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO ADVISE THE CUSTOMERS THAT HAVE ENROLLED THEIR VEHICLE INTO THE ONSTAR ADVANCED DIAGNOSTICS & REAL TIME DIAGNOSTIC ALERTS THEY MAY RECEIVE ALERTS FROM THEIR VEHICLE WHEN IT IS BEING SERVICED.
SB-16NA-131
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON VEHICLES DESIGNED TO OPERATE ON GASEOUS FUELS.
PIC-5374-D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIP5189B
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.
PIC6193A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS. THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.
PIC6197
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. PHONE WILL NOT CONNECT TO ANDROID AUTO.
PIP5168E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
SB-16-NA-042
THIS INFORMATIONAL BULLETIN ANNOUNCES THAT GM IS OFFERING AN ANDROID AUTO FEATURE UPGRADE FOR 2016 MODEL YEAR VEHICLES.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
SB-10-08-46-001C
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CONTACT ONSTAR FOR HARD MUTE REQUEST TO CORRECT A CUSTOMER CONCERN WHEN THE RADIO IS ON, IT DOES NOT MUTE ENOUGH WHEN THE ONSTAR® TURN-BY-TURN NAVIGATION DIRECTIONS ARE ANNOUNCED DUE TO CUSTOMER IMPROPERLY SETTING THE RADIO VOLUME HIGH ENOUGH WHEN THE TURN-BY-TURN NAVIGATION MESSAGES ARE PLAYED.
SB-15-06-03-001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE USEFUL ON DIAGNOSING BATTERIES THAT HAVE SET FOR A LONG PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.
PIC-4935-E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC4935E
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIT5389A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
SB-03-06-03-004Q
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY INFORMATION ON USING THE EL-50313 MIDTRONICS GR8 BATTERY TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.
SB-06-08-47-001L
THIS INFORMATIONAL BULLETIN PROVIDES WARRANTY INFORMATION ON USING THE SERVICE PROGRAMMING SYSTEM (SPS) FOR PROGRAMMING CONTROL MODULES
SB-07-06-01-016C
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION INTERNAL ENGINE NOISE OR DAMAGE AFTER OIL FILTER REPLACEMENT
SB-16-NA-119
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON GMS POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON VEHICLES ORIGINATING/SOLD IN CANADA.
PI-1302-A
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSTALL AN AIR INLET DEFLECTOR OVER THE HVAC AIR INLET TO CORRECT WATER LEAKING ON THE FRONT PASSENGER FLOOR DUE TO WATER RUNNING DOWN THE WINDSHIELD UNDER THE AIR INLET GRILLE PANEL, ENTERING THE BODY AIR INLET OF THE HVAC SYSTEM.
PI-0754-B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
SB-16-NA-117
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PURPOSE OF MAGNETIC DRAIN PLUGS.
PI-0281-E
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT CORROSION WITH CUSTOMERS.
PIC-5260-A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
SB-03-07-29-004K
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
SB-16-NA-104
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE FOOT OPERATED PARKING BRAKE ASSEMBLY FOR THE PRESENCE OF A RUBBER STOPPER AND REMOVE IF PRESENT TO CORRECT A CUSTOMER CONCERN THAT THE RED BRAKE INDICATOR IS ILLUMINATED WHEN THE PARKING BRAKE IS RELEASED DUE TO THE STOPPER NOT BEING REMOVED DURING ASSEMBLY.
SB-16-NA-106
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE G114 GROUND AND REPAIR AS NEEDED TO CORRECT A CUSTOMER CONCERN THAT THE VEHICLE STALLS, WILL NOT START, A/C DOES NOT WORK OR THE TRANSMISSION DOES NOT SHIFT CORRECTLY DUE TO A LOOSE GROUND CONNECTION AT G114.
SB-16-NA-107
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE RADIO TO CORRECT A CUSTOMER CONCERN OF RADIO INOPERATIVE, BLUE SCREEN, AM CLIPPING NOISE, HD ON/OFF STATUS NOT RETAINED IN STATIONS, TIME LAG ON TRANSITIONS, NO AUDIO WITH INTERNAL AMP, PARK ASSIST SYMBOL POSITION WRONG IN REAR VIEW CAMERA.
SB-16-NA-109
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS.
SB-16-NA-110
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A CLICKING NOISE OR DETENT FEEL WHEN DEPRESSING THE ACCELERATOR PEDAL ALL THE WAY DOWN THAT SHOULD BE CONSIDERED NORMAL OPERATION.
PIT5236G
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
00-03-10-002J
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.
PI0572C
This preliminary informational bulletin provides information on GM is implementing a new service strategy that uses a set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar®), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.
PI0360F
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars remotelink phone applications
09-06-04-026L
This informational bulletin provides information on Identifying Non-GM (Aftermarket) Engine Calibrations for Gasoline Engines Using Tech 2® or GDS 2 (U.S. and Canada)
PIC6120A
This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system.
08-00-89-014B
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics
07-00-89-037I
This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs
16-NA-075
This technical bulletin provides a procedure to relearn the power folding mirriors and road test to correct a conditon of power fold away mirriors glass shakes or flutters at normal driving speeds
PIP5376
This Preliminary Information communication advises the technician the 1.4L Engine Assembly Regular Production Option Code LE2 is on the engine exchange program. Dealerships are required to call the Product Quality Center not General Motors Technical Assistance Center to request an exchange.
15-06-03-002B
This informational bulletin provides information on Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
08-07-30-026C
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIC6116A
This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded.
PIP5232C
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
11-08-49-001P
This technical bulletin provides a procedure on how to take the vehicles out of transport mode for vehicles with the condition of Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing
16-NA-069
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
03-00-89-006M
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality Vehicles and Generating Higher CSi Scores
03-06-03-004O
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)
06-00-89-029M
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
09-00-89-002M
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
04-00-89-015K
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to what is acceptable and not.
12-03-10-001C
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
16-NA-055
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to properly disable the SIR system for repairs at or near
PI0851B
This preliminary informational bulletin provides information on Turbocharger Oil Feed and Return Line Inspection When Servicing Turbocharger Assembly
PIC6105C
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON THE STEPS TO TAKE TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE AN INACCURATE CLOCK. TECHNICIAN WILL CHECK FOR DIAGNOSTIC TROUBLE CODES IN THE TELEMATICS COMMUNICATION INTERFACE CONTROL MODULE. ENSURE THAT THE CUSTOMERS CONCERN DOES NOT RELATE TO THE NORMAL CHARACTERISTIC DESCRIBED IN THE LATEST VERSION OF PIC5839. TECHNICIAN WILL CALL ONSTAR TO INSURE ONSTAR HAS A GOOD LOCATION ON THE VEHICLE. IF THE ONSTAR UNIT STATUS IS DISABLED THE TECHNICIAN WILL EXPLAIN TO THE CUSTOMER THAT THERE IS AN OVER THE AIR UPDATE AVAILABLE FOR THE ONSTAR SYSTEM THAT MAY REPAIR THIS AS WELL BUT THEY WILL HAVE TO CONTACT ONSTAR AND ACCEPT TERMS AND CONDITIONS FOR A FREE 5 YEAR BASIC PLAN. IF THE CUSTOMER DOES NOT ACCEPT TERMS AND CONDITIONS BECAUSE THEY DO NOT WANT ONSTAR SERVICE, ADVISE THE CUSTOMER THAT ENGINEERING IS CURRENTLY EVALUATING OTHER METHODS TO REPAIR THIS CONCERN IF THE UNIT STATUS IS LISTED AS DISABLED AND THE CUSTOMER DOES NOT WISH TO REACTIVATE.
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
04-06-01-029H
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)
12-09-41-002C
This informational bulletin provides information on Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On or Set DTC B101D When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
PIP4990C
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON THAT COMES ON. TECHNICIAN MAY FIND A DIAGNOSTIC TROUBLE CODE U0101 CURRENT OR STORED HISTORY. TECHNICIAN SO CHECK TERMINAL PIN FIT AT TRANSMISSION CONNECTOR, UNDER HOOD FUSE BLOCK. ALSO THE TRANSMISSION CONTROL MODULE GROUND WILL NEED TO BE INSPECTED. TECHNICIAN WILL REVIEW THE APPROPRIATE SERVICE INFORMATION DIAGNOSTICS FOR DTC U0101.
PIP5226A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
08-08-44-015F
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and Instrument Panel Clusters (IPCs)
16-NA-033
This technical bulletin provides a procedure to replace the sunroof window motor for vehicles with the condition of sunroof or sunshade inoperatice and DTC U151B
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
PIT4720D
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
02-08-98-002F
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles that have the condition of rust showing at hem flange
PIP5370
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLE MAY HAVE AN EXHAUST FLUID QUALITY POOR ON THE DRIVER INFORMATION CENTER OR A DIESEL EXHAUST FLUID WARNING LAMP ON OR OTHER EXHAUST FLUID QUALITY RELATED CONCERNS. TECHNICIAN WILL INSPECT THE DIESEL EXHAUST FLUID FOR CONTAMINATION. TECHNICIAN SHOULD USE SERVICE INFORMATION FOR CONTAMINANTS IN DIESEL EXHAUST FLUID DIAGNOSIS AND USE SPECIAL TOOL J26568 OR EN50422 DIESEL EXHAUST FLUID REFRACTOMETER FOR FLUID TESTING.
06-08-50-009I
This informational bulletin provides Information on Passenger Presence Sensing System (PPS or PSS) Concerns with Custom Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices
03-08-46-004R
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
PI1520A
This preliminary informational bulletin provides information on a learn procedure on the battery sensor module on vehicles that have conditions of Stop/Start System is Inoperable After a System Repair and No DIC Message or DTC is Set
16-NA-019
This informational buleltin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares and information on transmission fast learns
16-NA-011
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a condition of infotainment system will not return to media after bluetooth call ends
06-06-01-010C
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
PIC5614A
Changing Turn-By-Turn Voice Response To Metric Or English Units
05-08-51-001H
This informational bulletin provides information on removing paint stains on the under side of protective shipping film
03-08-46-004Q
This informational bulletin provides information regarding Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules
16NA011
Infotainment System Will Not Return to Media After Bluetooth Call Ends
PIC6105B
This Preliminary Information communication provides information to the technician on the steps to take to diagnose and repair the vehicles that may have an inaccurate clock. Technician will check for Diagnostic Trouble Codes in the telematics communication interface control module. Ensure that the customer?s concern does not relate to the normal characteristic described in the latest version of PIC5839. Technician will call OnStar to insure OnStar has a good location on the vehicle. If the OnStar unit status is disabled the technician will explain to the customer that there is an over the air update available for the OnStar system that may repair this as well but they will have to contact OnStar and accept terms and conditions for a free 5 year basic plan. If the customer does NOT accept terms and conditions because they do not want OnStar service, advise the customer that engineering is currently evaluating other methods to repair this concern if the unit status is listed as disabled and the customer does not wish to reactivate.
PIT5353A
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT4943D
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
06-00-89-031D
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-073
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
15NA073
Difficult to Shift and/or Hard to Get into Gear
15-NA-069
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of torque specifications.
PIP5232B
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5241A
This Preliminary Information communication provides information to the technician about improper engine block cleaning during engine block service could lead to lines in the block deck surface that may be mistaken for cracks. Technician using improper block deck cleaning methods may see lines in the block deck surface. These lines are the result of using abrasive pad bristle devices to clean the gasket surface of the engine components. Technician should use the latest version of bulletin 00-06-01-012 for complete details on the use of these devices.
PIP5353
This Preliminary Information communication provides information to the technician about vehicles that may have a rough idle or misfire. Technician may find Diagnostic Trouble Code P0300 set in the Engine Control Module. Technician will need to utilize engine controls schematics to compare the Fuel Injector Control Circuit wire colors to determine if the wires are reversed. If this concern is found, inspect the related harnesses and terminals for signs damage due to the misrouting and repair.
00-03-10-006L
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force Variations and the difference between balancing a flange and flangeless rim.
PIT5214B
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIC3100E
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5411E
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
15-06-03-002A
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
10-00-89-005E
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information.
PIC6149
This Preliminary Information communication provides information to the technician about an intermittent concern for Service Keyless Entry message displayed in the Driver Information Center. Technician may find a Diagnostic Trouble Code B3124. Technician should inspect the trunk area for objects that may block the reception of the Rear Compartment Antenna.
15797
15797 - CUSTOMER SATISFACTION PROGRAM. CERTAIN VEHICLES MAY HAVE A CONDITION IN WHICH THE BODY SEALER WAS APPLIED OFF LOCATION ON THE VERTICAL SEAM BELOW THE RIGHT HAND TAIL LAMP. THE CUSTOMER MAY NOTICE WATER LEAKING INTO THE PASSENGER SIDE OF THE TRUNK BELOW THE TAIL LAMP IF THE CAR IS LEFT OUTSIDE DURING A HEAVY RAINSTORM OR, IN SOME CASES, DURING A CAR WASH. DEALERS ARE TO APPLY AUTOMOTIVE BODY SEALER TO THE RIGHT HAND OUTSIDE EDGE OF THE VERTICAL SEAM BELOW THE RIGHT HAND TAIL LAMP.
02-07-30-029Y
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to contact PQC prior to replacing an assembly (U.S. and Canada only).
15-NA-044
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
01-06-01-011I
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
08-08-44-029F
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI0799A
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer concern of seeing a white film/residue on the IP pad and/or door trim panels.
PIC5953B
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
15-NA-030
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers and booster packs.
PIP5338
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
15-06-03-001A
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
PIC6106B
This Preliminary Information communication provides information to the technician about vehicles that may have the radio display that will go blank and come back on after a few seconds then display may show the splash screen or come back on to the last screen that was displayed. Technician should USB update the radio using Tis2Web and follow up with a Service Programming System program.
PIP5334
This Preliminary Information communication provides information to the technician about vehicles that have a tick or squeak noise from the upper engine. Technician should check for loose or improperly torqued spark plugs before performing intrusive engine mechanical testing or component replacement.
PIC6105A
This Preliminary Information communication provides information to the technician about vehicles that the clock time will change unwanted and become inaccurate. Technician should check to ensure the radio is set on "Automatic Clock Update" by pressing the clock in the upper right corner of the screen and making sure the box has a check in it. If the time updates correctly while the vehicle is otside, the system is working as designed and release the vehicle to the customer.
PIE0347
This engineering information bulletin is requesting information from dealers on a customer concern that the vehicle is difficult to shift or will not shift into gear.
08-08-44-029E
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
PI1356D
This preliminary informational bulletin provides repair information for a customer concern that the radio screen is blank, locked-up or is frozen, however, the radio audio may still be heard.
05-03-07-009H
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
PI0653C
This preliminary informational bulletin provides dealership personnel with policies and procedures regarding damaged, disassembled or improperly packaged turbochargers returned to Warranty Part Center.
PIT5119D
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
PIT5468
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
PIP5325
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
PIP5329
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P0341 and or P0366 set. If the technician has duplicated the concern replace the related Camshaft Position sensor and retest for the code. If the Diagnostic Trouble Code returns technician should check the history to see if the vehicle was in a collision. If the vehicle has been in a collision technician should call General Motors Technical Assistance Center.
GCUS-3-304
15622A - Customer Satisfaction Program (revised the part information, service procedure, and warranty sections). Certain 2014-2016 model year Chevrolet Cruze model vehicles may have been built with the front knuckle to hub attachment bolts below GM?s torque specification. This condition could result in noise from the front suspension and separation of the steering knuckle to hub while driving, resulting in loss of steering control, potentially increasing the risk of a crash. Dealers are to inspect the left and right front knuckle to hub attachment bolts and torque the bolts to specification.
PIT5460
This Preliminary Information communication provides information to the technician about vehicles with the rear view camera will be displayed for a longer than usual amount of time. Technician should not replace any parts General Motors is currently evaluating this concern.
PB-15622-A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-08-24-15
GENERAL MOTORS: PARTS FOR MOST VEHICLES, CLUTCH, MASTER CYLINDER ASSEMBLY ARE, REQUIRED AND REQUESTED, TO BE RETURNED AND NEED TO REORDER REPLACEMENT PARTS USING SAME PART NUMBERS. *PE
15-00-89-005
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
PIP5313
This Preliminary Information communication advises the technician that the E80 Engine Control Module part numbers 12655021, 12668437, and 12672502 has been placed on restriction through General Motors Technical Assistance Center to assist GM Engineering with product feedback. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
10-08-110-001D
This informational bulletin provides information on the proper use of GM floor mats.
15622
15622 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2015 AND 2016 MODEL YEAR CHEVROLET CRUZE MODEL VEHICLES MAY HAVE BEEN BUILT WITH THE LEFT FRONT KNUCKLE TO HUB ATTACHMENT BELOW GMS TORQUE SPECIFICATION. THIS CONDITION COULD RESULT IN NOISE FROM THE FRONT SUSPENSION AND SEPARATION OF THE STEERING KNUCKLE TO HUB WHILE DRIVING, RESULTING IN LOSS OF STEERING CONTROL, POTENTIALLY INCREASING THE RISK OF A CRASH. DEALERS ARE TO INSPECT THE LEFT FRONT KNUCKLE TO HUB ATTACHMENT BOLTS AND TORQUE THE BOLTS TO SPECIFICATION.
00-06-01-026G
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
07-00-89-037H
This warranty administration bulletin provides policy information on courtesy transportation and roadside assistance programs.
09-09-40-001C
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
15622 STOP MESS
15622 - STOP DELIVERY ORDER. ON SOME 2015 AND 2016 MODEL YEAR CHEVROLET CRUZE VEHICLES THE LEFT FRONT KNUCKLE TO HUB ATTACHMENT IN THESE VEHICLES MAY HAVE BEEN MANUFACTURED WITH TORQUE BELOW GMS SPECIFICATION.
09-00-89-002L
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
PIC5932A
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
09-06-04-026K
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline engines using Tech 2® or GDS 2 (U.S. and Canada).
99-01-39-004G
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
03-06-03-003E
This warranty administration bulletin provides policy information on ACDelco® replacement battery warranty procedures.
PIP4543D
This Preliminary Information communication provides information to the technician about a concern with diagnostic trouble codes P0011 P0014 P0016 or P0017 in the engine control module after a repair involving the camshaft actuators. There is a unique black plastic oil sleeve that is between the end of the cam actuator and the camshaft. This sleeve directs oil into the actuator to adjust the timing. If the sleeve is damaged or missing, the engine control module cannot control the cam actuator movement and will set the diagnostic trouble codes.
03-07-29-004J
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
PIT5443
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
03-00-89-006L
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
01-08-51-003E
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
05-06-04-022M
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
03-06-03-004N
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
PI0233E
This preliminary informational bulletin adds the 2015-2016 model years to repair information to correct a customer concern of inaccurate or slow response of outside air temperature display.
PI0867B
This preliminary informational bulletin provides diagnostic tips and repair information to correct a customer concern for intermittent engine no crank, intermittent exhaust Camshaft Position (CMP) sensor signal.
02-00-89-002O
This informational bulletin provides information for dealers/technicians on when and how to submit a Field Product Report (FPR) (U.S. Dealers Only).
PIC6107
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
99-00-89-019M
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
09-00-89-002K
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer inventory.
15-00-89-004A
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
00-06-01-026F
This informational bulletin provides information to technicians regarding intake manifold inspection/replacement after severe internal engine damage.
PI0091B
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
02-08-42-001H
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
11-08-49-001O
This technical bulletin provides repair procedure information to correct a customer concern of Transport Mode On message displayed in Driver Information Center (DIC) and/or battery light is flashing.
15-00-89-004
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
PIC5779F
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
PIT5399
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
13-08-116-001B
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
PI1440
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor emanating from HVAC system.
04-00-89-015J
This warranty administration bulletin communicates GM required operating procedures (U.S. only) for service operations.
09-00-89-016D
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
12-06-01-008B
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
15-00-89-003
This informational bulletin provides information on dealer reimbursement procedures for Customer Assistance Center (CAC) Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).
PI0421C
This preliminary information bulletin provides a procedure to remove and replace the clutch actuator cylinder elbow seal for concerns regarding a fluid leak after clutch actuator replacement.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.