PIP4902W
Service Bulletin/Repair Instructions
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP4902W
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT5099J
PI to help diagnose A/C concern
PIT3271Q
This preliminary information communicates information about how to determine if a wheel and tires size change is available.
PIP4902V
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIP6104
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical Assistance Case in CX Connect.
PIP4902U
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIT6463
This PI communicates information that a dealer may need to select the correct J2534 Device "Bosch - MDI 2" to communicate with the vehicle
PIT5214G
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer’s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
PIT6453
This PI communicates information on the change of Diagnostic and Scan Tool availability from SI/TLC to Isuzu IDSS.
13598
New Vehicle Monitoring Programs Section in IVH
PIP4902T
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
PIC5650M
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
PIT6180A
This Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
PIP4902S
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
25-NA-156
This service bulletin provides information on Tire Sidewall Irregularities.
00-06-01-026R
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
PIT5074R
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini 50 terminal test probe, replacement terminals, and terminated leads.
15-NA-010
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
07-00-89-037W
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
13-08-116-001K
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
25-NA-052
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling system and replace the parts that may be contaminated due to oil in system.
25-NA-065
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for analysis.
15-06-03-001F
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
11-00-89-005Y
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
05-08-51-001L
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
07-00-89-037V
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
10-08-110-001L
This service bulletin provides information on proper use of floor mats.
07-00-89-037U
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
03-06-01-023I
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
PIT5962B
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
PIT6261
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
08-07-30-035I
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
19-NA-219
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
16-NA-274
THis Informational bulletin provides important instructions for contacting the Fleet Action Center for repair authorization prior to replacement of certain parts.
21-NA-043
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
04-06-01-029K
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
24-NA-040
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
10-00-89-009F
This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
03-06-01-023H
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
20-NA-132
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
99-00-89-019Z
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
07-00-89-037T
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
23-NA-154
This bulletin provides information on Warranty Administration – Required Operating Procedures - 8 Points (U.S. Only).
04-06-04-051J
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
23-NA-219
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
18-NA-146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
07-00-89-036K
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
02-00-89-002X
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
23-NA-142
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
PIT3271P
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
24-NA-174
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
General Communication
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
05-03-08-002J
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
18-NA-073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
23-NA-044
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
01-00-89-010S
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
07-06-01-016J
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
23-NA-141
This informational bulletin advises the technician that the engine and related parts will be debited if found that the tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
00-06-01-012N
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
05-06-04-022V
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
16-NA-222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
PI0754G
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
16-NA-158
This service bulletin describes the U.S. Dealer Special Tool Loan Program process.
12-01-37-001G
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
24-NA-141
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
00-03-10-002M
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
17-NA-157
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the possibilities of what may happen using the incorrect filter.
99-04-20-002O
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
04-06-04-051I
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
16-NA-383
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
22-NA-070
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part replacements.
18-NA-099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
22-NA-018
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S. Dealers Only).
18-NA-125
This service bulletin provides information for engine oil life monitor operation calculation.
20-NA-016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
16-NA-331
This warranty administration bulletin provides the information on General Motors Tire Warranty Policies and Procedures for Low Cab Forward Medium Duty Trucks (US Medium Duty Dealers Only).
08-07-30-035H
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16-NA-119
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
09-00-89-008G
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
18-NA-067
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
06-00-89-029V
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
10-08-110-001K
This service bulletin provides information on proper use of floor mats.
13-08-116-001J
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004G
This service bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
23-NA-125
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME) FAQs.
17-NA-052
This bulletin updates the position of General Motors on refinishing aluminum wheels. GM has determined that wheel refinishing under warranty will no longer be performed.
10-08-45-001H
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
23-NA-103
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical Assistance Center (TAC).
22-NA-223
This informational bulletin advises the tech of a possible wrong fluid used when performing a maintenance or repair to the rear axle.
07-00-89-037S
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
11-00-89-005X
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
17-NA-073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
22-NA-074
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
23-NA-186
This bulletin advises of a new vacuum pump and pulley and a new way to route and secure the vacuum hose.
02-08-42-001J
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIT5962A
This Preliminary information communicates a GM part number for reflective high temperature heat or insulating tape when repairing wiring harnesses.
03-00-91-001I
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
22-NA-167
This informational bulletin provides information on Light and Medium Duty Truck Product Identification and Warranty Summary Chevrolet/GMC Dealers.
05-00-89-029F
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
17-NA-170
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
99-00-89-019Y
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
02-00-89-002W
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
20-NA-051
This informational bulletin provides information on the Low Cab Forward trucks and the Alpine Radio Exchange Program.
23-NA-153
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
09-00-89-016H
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
15-00-89-004F
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010R
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
04-06-04-051H
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
03-06-01-023G
This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
17-NA-066
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
99-09-40-005I
This service bulletin provides information on availability for a seat belt extender.
13-08-116-001I
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
02-00-89-002V
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
12-03-10-001E
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
11-00-89-005W
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
12-03-10-001D
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
04-00-89-015Z
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
08-07-30-035G
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
10-08-110-001J
This service bulletin provides information on proper use of floor mats.
11-00-89-005V
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
03-06-04-017S
This service bulletin provides information on availability of Diesel Fuel additives.
00-06-01-012M
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
00-06-01-026Q
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
22-NA-009
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
07-06-01-016I
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
15-NA-017
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted to GM for payment.
18-NA-263
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
PI0754F
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
99-04-20-002N
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operation.
02-00-89-002U
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
09-00-89-008F
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
21-NA-124
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-219
This informational bulletin provide Information on Turn Signal Lenses Cracking.
22-NA-205
This service bulletin provides information on Module Harvesting.
99-00-89-019X
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
22-NA-195
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
03-06-04-017R
This service bulletin provides information on availability of Diesel Fuel additives.
05-06-04-022T
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
06-00-89-031H
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
07-06-01-016H
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
13-08-116-001H
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
15-00-89-004E
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
01-00-89-010Q
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
05-00-89-072F
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
00-06-01-012L
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
03-06-04-017Q
This service bulletin provides information on availability of Diesel Fuel additives.
04-06-04-051G
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
10-06-05-002K
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
00-06-01-026P
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
11-00-89-005U
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
21-NA-068
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
05-00-89-029E
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
22-NA-181
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
11-00-89-005T
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
17-NA-050
This service bulletin explains how a health report is required when doing repairs on MD LCF vehicles.
20-NA-065
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
18-NA-296
This informational bulletin provides the technician on how to check the DPF ceramic and where to get cleaning products for cleaning filters.
04-00-89-015X
This bulletin provides information on Warranty Administration â Required Operating Procedures - 8 Points (U.S. Only).
22-NA-135
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
12-01-37-001F
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
16-NA-109
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
18-NA-339
This informational bulletin provides information for dealers/technicians on approved 6-speed aisin automatic transmission on vehicle internal repairs.
01-00-89-010P
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
01-00-89-010O
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
PIT3271M
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
150089004C
This service bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered fluid seepage.
18NA073
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
040089015V
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
16NA019
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
18NA263
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S. Only).
060089031F
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
PIT5074N
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
030604017O
This Informational Bulletin provides information on availability of Diesel Fuel additives.
PIC6208E
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
000310002L
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PIT3271K
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PI0754D
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal characteristic.
20NA213
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and PF48.
16NA222
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
18NA103
This service bulletin provides information to correct a customer concern of an in-tank fuel pump whining noise, engine hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated.
PIP5684C
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
050604022R
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
PIP5628C
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
110089005P
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
18NA306
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
990089019U
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
18NA099
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5226D
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5650H
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
PIT5698A
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
19NA255
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
PIC5453D
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5684B
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
150089002B
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
PIP4902N
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
20NA132
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
990089019T
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
PIC5453C
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
110089005O
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S. Only).
060089029T
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIP5628B
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5725
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
030089006R
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029S
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
20NA098
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the part and ordering it from the EPC.
PIP5684A
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
060089029R
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
PIC5650G
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
060089029Q
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
100089005I
This warranty administration bulletin explains to the technician that when using wiring repair labor operations, additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
060089029P
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
070089037O
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance programs.
020089002S
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. Dealers Only).
20NA057
This informational bulletin provides information for dealers/technicians on Mobileye Exchange Program and Troubleshooting.
050310020G
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
20NA051
This informational bulletin provides information on the Low Cab Forward trucks and the Alpine Radio Exchange Program.
990089019S
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program Information.
040601029J
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
19NA104
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front grille or radiator area.
19NA219
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
040089015U
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S. Only).
16NA119
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
PIT3099T
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
110089002D
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
15NA010
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
20NA016
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
PIP5540F
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
16NA383
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
100089009D
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
080089014F
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5621A
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
010842001M
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIT3271J
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT5074M
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
990420002K
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
16NA274
THis Informational bulletin provides important instructions for contacting the Fleet Action Center for repair authorization prior to replacement of certain parts.
17NA248
This informational bulletin provides the dealer with key information for cutting a new key.
PIP5684
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
17NA050
This informational bulletin explains how a health report is required when doing repairs on LCF vehicles.
PIP5540E
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
010089010N
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
030604017N
This Informational Bulletin provides information on availability of Diesel Fuel additives.
17NA073
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
PIP5522D
This Preliminary information communicates A vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm. A broken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced. On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
19NA212
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft alignment pin has been sheared away.
PIP5632B
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIT3099S
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
18NA146
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
000601026M
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after severe internal engine damage.
070601016F
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
16NA109
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
PIT5698
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
PIC6208D
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
990089019R
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
PIP5662
This Preliminary information communicates A vehicle may have a concern of a MIL illuminated with a P208E set in the DEF control module. Possible stuck DEF injector If the diagnostic leads to the DEF injector, replace the DEF injector and the DEF Supply Pump Filter Element
PIT5569A
This Preliminary information communicates direction and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
PIT3099R
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
050604022Q
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
100845001G
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
PIT5074L
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
PIP5632A
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
080730035D
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
16NA331
This warranty administration bulletin provides the information on General Motors Tire Warranty Policies and Procedures for Low Cab Forward Medium Duty Trucks (US Medium Duty Dealers Only).
PIP5640
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
080089014E
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIC5260C
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
030603004Y
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
1008110001H
This informational bulletin provides information on proper use of floor mats.
110089005N
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
030089006Q
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
060089029O
This informational bulletin provides information on interior cleaning products and what is offered to clean the interiors of GM vehicles.
040089053G
This informational bulletin provides information for the dealer technician to gather as much information to help aid Engineers by completely filling out requested reports.
1008110001G
This informational bulletin provides information on proper use of floor mats.
PIP4902M
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
100845001F
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
090089002Q
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
PIP4902L
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
050604022P
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
120089002C
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
PIP5540D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PI0564K
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
090089016F
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
090089002P
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
010089010M
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
080089014D
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
17NA346
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
030603004X
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty replacements.
17NA170
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
100089005H
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
040089015T
This warranty administration bulletin provides policy information on required operating procedures.
18NA371
This Bulletin will instruct the Chevrolet Medium Duty Dealer on how to download and request a Chevrolet Vehicle Insight (Health) report for Diesel engine equipped vehicles only.
18NA339
This informational bulletin provides information for dealers/technicians on approved 6-speed aisin automatic transmission on vehicle internal repairs.
PIC6073E
This Preliminary Information communication provides information to the technician about the Media Oriented Systems Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
PIT5214D
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
010842001L
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
080089014C
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
PIP5540B
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
060850009J
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS) concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
PIP4925B
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
This Preliminary information communicates
PIT5099D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5596
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
PIP4902K
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
PIP5163D
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC6095C
This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
PIC5260B
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
PIT5099C
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5953D
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5373B
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
18157
18157 - Customer Satisfaction Program. Certain Low Cab Forward vehicles, equipped with diesel engines, may have a condition in which the Fuel Tank Sub Unit float arm in the rear-mounted fuel tank may become disconnected causing the fuel gauge to display ?Empty? (E) regardless of the actual fuel level. Dealers are to replace the Fuel Tank Sender Unit.
PIT5399A
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
18NA141
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a normal characteristic.
1208132001E
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
PI0754C
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal characteristic.
PI0281G
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
PI0564J
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
060089031E
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
000089027J
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in vehicles.
030089006P
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
17NA215
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED, No WiFi Operation, and/or Limited OnStar® Module Functionality After OnStar Module Replacement for Another Condition.
090604026N
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S. and Canada
110089005L
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
060601010D
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
18NA027
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on USB.
PIP5226B
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3271H
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
050851001I
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the shipping film.
PI0653E
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged Turbochargers Returned to Warranty Part Center.
PIP5540
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
050604022O
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
PIP5522B
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
PIT5354B
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
040089015R
This warranty administration bulletin provide policy information on required operating procedures.
070089037L
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance programs.
PIC5839D
This Preliminary Information communication provides information to the technician about vehicles that may have a clock that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
070089036I
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital pictures.
16NA239
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
16NA356
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
17NA142
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
16NA158
This bulletin describes the Dealer special tool loan program process.
PIP5533
This Preliminary information communicates to the dealerA vehicle may have a concern with Engine performance, Engine machancal (burnt pistons), fuel in oil and/orfuel system performance.Fuel fill/ fuel vent lines mis - routed kinked/pinched.Inspect the fuel tank return and fuel tank vent lines for kinks or restrictions and repare as needed.
140089004D
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key ring sizes and applying a QR code sticker or barcode sticker to a key fob.
PIC5492F
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
PIT5353B
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
IPC Odometer Programming Method Quick Reference Guide
150089004B
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Essential Tools that Include Consumable Parts (U.S. Only)
150603002H
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
16-NA-175
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
PIT5236K
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
PIP5522A
This Preliminary information communicatesA vehicle may have a concern of engine noise and/or a misfire. This may be caused by a broken rocker arm.Abroken rocker arms that could result in the valve dropping to the cylinder, causing a catastrophic failure and the engine requires replacement due to cylinder head and block damage. If a broken rocker arm is found check to see if the valve dropped into the cylinder if so the engine will need to be replaced.On occasions the valve will not drop, reinstall any valve keepers and replace all the intake rocker arms.
PIP4723C
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5074K
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
17NA056
This informational bulletin explains that all vehicles are shipped with the F-3 fuse and if the fuse has been removed for inventory, not to submit a claim to replace the fuse.
040601029I
This informational bulletin explains the importance of maintaining the vehicle.
100089005G
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
PIT5389E
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
030604017L
This Informational Bulletin provides information on availability of Diesel Fuel additives.
070601016D
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
00-06-01-026J
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine Damage.
99-08-51-001D
Thins informational bulletin provides information on Paint-less Dent Repair Process.
03-08-46-004T
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIP5163C
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5932B
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
17-NA-248
This informational bulletin provides the dealer with key information for cutting a new key
17-NA-244
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
17-NA-242
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to reprogram modules that have been already reprogrammed.
PIP5507B
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
17-NA-230
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will replace it via the website provided.
PI0564I
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
PIC5611E
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
PIP5507A
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIP5507
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
PIC6287
This Preliminary Information communication provides information to the technician about vehicles that the radio will not retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
PIC5588D
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIC6283
This Preliminary Information communication provides information to the technician about vehicles that when watching a movie the audio does not match the video when playing though the vehicles speakers. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT3099P
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-03-10-002K
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed Aluminum Wheels.
PI1410B
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
00-06-01-012G
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
05-00-89-029D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and Recommendations.
17-NA-142
This informational bulletin provides information on Wireless Charging Module Diagnosis.
11-00-89-005K
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer Enthusiasm.
17-NA-126
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
PI0281F
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
10-08-110-001F
This informational bulletin provides information on proper use of floor mats.
99-04-20-002J
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal operations.
17-NA-067
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
16-NA-314
This informational bulletin provides information on the proper coolant part numbers for the Chevrolet low cab forward diesel.
16-NA-337
This New Model Features Bulletin provides various general information topics including engines, TC systems, fuel systems etc., and Training Courses and Special Tools to the Service, Parts and Sales Personnel in order to familiarize them with the vehicle.
03-06-04-017K
This Informational Bulletin provides information on availability of Diesel Fuel additives.
17-NA-056
This informational bulletin explains that all vehicles are shipped with the F-3 fuse and if the fuse has been removed for inventory, not to submit a claim to replace the fuse.
PIT5389C
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIC4935F
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5959C
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
PIC5588C
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
PIP4902J
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
08-03-10-006F
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats. for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
03-08-46-004S
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIC5759B
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
PIT4733K
This Preliminary Information communication provides information to the technician that customers may inquire as to the availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
PIT5236J
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
08-08-44-015H
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
PIC5492E
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
05-03-08-002H
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
PIT5354A
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity. Technician should check the Regular Production Option Code list for (VV4).
PIT3099N
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
06-08-64-001D
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
01-03-10-003M
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
16-NA-337 v2
This New Model Features Bulletin provides various general information topics including engines, TC systems, fuel systems etc., and Training Courses and Special Tools to the Service, Parts and Sales Personnel in order to familiarize them with the vehicle.
00-03-10-003V
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
PIT5389B
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
03-06-04-017J
This Informational Bulletin provides information on available Diesel Fuel Additives.
PIT5236H
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
16NA314
This informational bulletin provides information on the proper coolant part numbers for the Chevrolet low cab forward diesel.
030604017J
This Bulletin has been Revised to add the 2017 Colorado, Cruze, Canyon, Chevrolet & GMC Light/Medium Duty Trucks. Please discard Corporate Bulletin Number 03-06-04-071I
080730026D
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
050604022N
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
090089002N
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before sold (prepping) to the customer.
100844006D
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc information.
16NA337
This New Model Features Bulletin provides various general information topics including engines, TC systems, fuel systems etc., and Training Courses and Special Tools to the Service, Parts and Sales Personnel in order to familiarize them with the vehicle.
00-03-10-003U
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
05-08-44-024E
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation Discs .
09-00-89-008C
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
09-00-89-016E
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
11-00-89-005J
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy Guidelines.
02-08-98-002G
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the flanges when the repairs are done.
08-08-44-015G
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
16-NA-311
This informational bulletin provides information to resolve a limited slip differential chattering noise.
16-NA-312
This informational bulletin provides information that being issued to help the dealers identify a potential source for fuel contamination and the incorrect fuel filler neck installation.
16-NA-313
This informational bulletin provides information on a diagnostic procedure for a fluid leak on the power steering unit.
PI0653D
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
05-00-89-072D
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and a list of websites for additional information.
PIT5074J
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
PI1394A
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
PIT5411F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER, RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
PI0388F
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
PIP5373A
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.
070898001B
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES. GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
110849001S
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
00-06-01-026H
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine damage.
16-NA-223
This informational bulletin provides information on installing the correct tires for vehicles with the condition of under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
09-06-04-026M
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline engines using Tech 2 or GDS 2.
99-08-51-007G
This informational bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
03-03-10-007J
This informational bulletin provides information on the temporary tire flat spotting condition.
12-08-132-001D
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse replacement.
PIC5374D
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
PIC4707E
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN. THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
PIC5088F
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC5260A
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN. VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
00-03-10-002J
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper cleaners to use to fix the conditions due to multiple causes.
08-00-89-014B
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S. technical Assistance and the use of strategy based diagnostics
16-NA-069
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for 15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
03-06-03-004O
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America ONLY)
06-00-89-029M
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces, Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
09-00-89-002M
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
02-08-42-001I
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
01-08-42-001K
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.