PIP5601C
Service Bulletin/Repair Instructions
This PI communicates the requirement to provide a pico file to receive diagnostic assistance from TAC.
Vehicle report
2004 CHEVROLET MONTE CARLO
Service bulletins
425 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
PIP5358D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
PIP4723J
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5099H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT3271P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
General Communication
Service Campaign
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
24-NA-141
Service Bulletin/Repair Instructions
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
16-NA-383
Service Bulletin/Repair Instructions
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
18-NA-099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
24-NA-098
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
09-00-89-008G
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
10-08-45-001H
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
22-NA-074
Service Bulletin/Repair Instructions
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
02-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
PI1394B
Service Bulletin/Repair Instructions
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
PIP5601B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
23-NA-219
Service Bulletin/Repair Instructions
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
03-00-91-001I
Service Bulletin/Repair Instructions
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
17-NA-170
Service Bulletin/Repair Instructions
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
10-00-89-006J
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIT5099G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
07-08-49-020R
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
23-NA-153
Service Bulletin/Repair Instructions
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
18-NA-073
Service Bulletin/Repair Instructions
This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
PIP5628G
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5358C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
19-NA-219
Service Bulletin/Repair Instructions
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
PIP5628F
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
22-NA-009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
17-NA-073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
01-08-42-001O
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
PIP5628E
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
09-00-89-008F
Service Bulletin/Repair Instructions
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIP5540J
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
21-NA-124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
PIT3271N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
22-NA-205
Service Bulletin/Repair Instructions
This service bulletin provides information on Module Harvesting.
10-00-89-006I
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIC5453D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
22-NA-195
Service Bulletin/Repair Instructions
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
06-00-89-031H
Service Bulletin/Repair Instructions
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification.
22-NA-181
Service Bulletin/Repair Instructions
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
PIP5640A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
20-NA-065
Service Bulletin/Repair Instructions
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
PIT5099F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5358B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
12-00-89-003B
Service Bulletin/Repair Instructions
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with independent causes (GM Canada Dealers Only).
PIT3271M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIT3271L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP4723F
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
22NA009
Service Bulletin/Repair Instructions
This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
000090002L
Service Bulletin/Repair Instructions
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate ride characteristics of GM cars and trucks.
030091001H
Service Bulletin/Repair Instructions
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
PIT3099U
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
010842001N
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
21NA124
Service Bulletin/Repair Instructions
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
100089006H
Service Bulletin/Repair Instructions
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
PIP5358A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have an unusual noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
18NA099
Service Bulletin/Repair Instructions
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
PIP5163E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIP5540G
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5725A
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
PIT3271K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5628C
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIP5226D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT5099E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIC5453C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
PIP5628B
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
070849020Q
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIP5725
Service Bulletin/Repair Instructions
This Preliminary information communicates the use of Winter grade fuel during the warm months of 2020 and the potential rivability issues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concerns should not be single events but should be multiple occurrences associated with hot days.
DOR-C5P7J-03
Service Bulletin/Repair Instructions
This SKU is an EGR Valve. The customer communication requested return of unsold inventory to inspect the electrical leads in the motor. The leads may become worn leading to voltage spikes which can cause a fault and engine light to come one; voltage spikes may also cause performance issues from misfiring.
DOR-Q9L3Y-03
Service Bulletin/Repair Instructions
This SKU is an HVAC Air Door Actuator. The customer communication requested return of unsold inventory to inspect the housing. There may be a gap between the 2 halves of the housing causing the actuator to bind and a loss of HVAC air door control. Loss of HVAC air door control can lead to discomfort as it may be stuck in a single orientation.
PIT3099T
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIP4723D
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIP5540F
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
16NA383
Service Bulletin/Repair Instructions
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
100089009D
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security rules and information on GM keycode look-up applications.
010842001M
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIT3271J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
100089006G
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
PIP5540E
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5601A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
100089009C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
17NA073
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
150844001J
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
PIT3099S
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
PIT3099R
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
100845001G
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
060847001O
Service Bulletin/Repair Instructions
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP5640
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
PIP5226C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
070849020P
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
100845001F
Service Bulletin/Repair Instructions
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive finish".
PIP5540D
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5628
Service Bulletin/Repair Instructions
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
PIC3074F
Service Bulletin/Repair Instructions
This PI was created to address XM signal performance with the sunroof open and covering the antenna.
17NA170
Service Bulletin/Repair Instructions
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
010842001L
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines.
PIP5540B
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
060847001N
Service Bulletin/Repair Instructions
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not when replacing a module.
PIP4925B
Service Bulletin/Repair Instructions
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
PIT5353C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5601
Service Bulletin/Repair Instructions
This Preliminary information communicates
PIT5099D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5163D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5099C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIT5399A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
060601010D
Service Bulletin/Repair Instructions
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system.
PIP5226B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIT3271H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIP5540A
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP5540
Service Bulletin/Repair Instructions
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIC3100F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIT5353B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
070849020M
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide
150089004B
Service Bulletin/Repair Instructions
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
150089005A
Service Bulletin/Repair Instructions
Essential Tools that Include Consumable Parts (U.S. Only)
PIP4723C
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIT5389E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
PIT3099Q
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
PIP5163C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIC5588D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
00-06-01-012G
Service Bulletin/Repair Instructions
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on engine surfaces.
15-08-44-001I
Service Bulletin/Repair Instructions
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
15-08-73-001A
Service Bulletin/Repair Instructions
This informational bulletin explains how to update the older Onstar module software to new software over GSA.
06-08-47-001M
Service Bulletin/Repair Instructions
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and reprogram modules.
10-00-89-006F
Service Bulletin/Repair Instructions
This informational bulletin provides information for dealers how to submit a product information report.
PIT5389C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
07-07-30-010D
Service Bulletin/Repair Instructions
This informational bulletin provides explanation on how to take snapshot data with a Tech 2 and upload it to a computer and where to email the info to.
PIC4935F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
PIP4723B
Service Bulletin/Repair Instructions
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
PIC3278G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4801H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
PIC5588C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIP5029H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
PIP5338A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
17-NA-016
Service Bulletin/Repair Instructions
This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.
03-08-46-004S
Service Bulletin/Repair Instructions
This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
07-08-49-020L
Service Bulletin/Repair Instructions
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
PIC5492E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
05-00-89-055F
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill procedures.
PIT3099N
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIP5163B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT5389B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
09-00-89-008C
Service Bulletin/Repair Instructions
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the warranty transaction submission procedures that support the Personal Property Damage process.
PIC5453B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT GENERAL MOTORS AND GENERAL MOTORS OF CANADA COMPANY DO NOT SUPPORT CROSS BORDER SALES. THE GENERAL MOTORS OF CANADA CUSTOMER CARE CENTRE IS THE SOLE AUTHORIZED PROVIDER OF A CERTIFICATION CONFIRMATION LETTER WHICH HELPS OUR CUSTOMERS IDENTIFY IF THEIR VEHICLES MEETS THE REQUIRED USA REGULATORY STANDARDS NECESSARY FOR IMPORTATION INTO THE USA.
07-08-49-020K
Service Bulletin/Repair Instructions
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
PIC5491J
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP. TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
PIP5029G
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.
PI1394A
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
16NA260
Service Bulletin/Repair Instructions
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REPROGRAM THE MEDIA DISC PLAYER WITH THE LATEST CALIBRATIONS TO CORRECT A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.
000601012F
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE GASKET SEALING SURFACES.
030604017I
Service Bulletin/Repair Instructions
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
PIP5094A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE, IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
PIT-5485-B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIT5485B
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC5088F
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN. THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
PIC-4935-E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC-5050-A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIC4935E
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
PIC5050A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON REPAIRING THE CONCERN. A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.
PIT5389A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
PIT5485A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN, IF UNABLE TO PLACE AN ONSTAR CALL IN THE IGNITION ON MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.
PIC6181
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician after the OnStar Canada upgrade the OnStar Vehicle Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
08-07-30-026C
Service Bulletin/Repair Instructions
This informational bulletin provides information on vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak and that this is considered a normal conditon and no repairs are necessary
PIP5232C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIT5484A
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIC5953A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
02-08-42-001I
Service Bulletin/Repair Instructions
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not
11-00-89-005I
Service Bulletin/Repair Instructions
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S. Only)
PIP5226A
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.
01-08-42-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
PIT4720D
Service Bulletin/Repair Instructions
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
16-NA-025
Service Bulletin/Repair Instructions
This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
03-08-46-004R
Service Bulletin/Repair Instructions
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only)
06-06-01-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period.
PIC6140B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT5353A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIT5484
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT5486
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT4943D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
06-00-89-031D
Service Bulletin/Repair Instructions
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
07-08-49-020J
Service Bulletin/Repair Instructions
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15-NA-079
Service Bulletin/Repair Instructions
OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
PIP5232B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
15-08-44-001F
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
15-08-44-001G
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
PIC6140A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIC5953B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP5338
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
PIT5464
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP5325
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
09-09-40-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
PIC6107
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
15-08-44-001C
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
PIC6101
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are unable to receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.
PIT5384A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
02-07-30-052J
Service Bulletin/Repair Instructions
This informational bulletin provides technicians with information regarding automatic transmission oil cooler flow test essential tool J-45096 TransFlow®.
05-06-04-035E
Service Bulletin/Repair Instructions
This informational bulletin provides dealership personnel with information on flexible fuel vehicles (FFVs) and the usage of E85 fuel in GM vehicles.
15-08-44-001A
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-44-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
02-08-42-001H
Service Bulletin/Repair Instructions
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
PIT5399
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
PIC4310L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
05-08-46-006T
Service Bulletin/Repair Instructions
This informational bulletin provides information to dealership personnel on upgrading certain OnStar Analog/Digital-Ready Systems to OnStar Generation 6 Digital-Capable System.
15-08-44-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on a GM of Canada OnStar® cellular communication upgrade.
15-08-73-001
Service Bulletin/Repair Instructions
This informational bulletin provides information on communication with OnStar® module after Canadian cellular upgrade.
PIT5264C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
05-00-89-055E
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information to clarify proper transaction administration of GM Dealer Empowerment Program and Goodwill Cases.
06-08-47-001K
Service Bulletin/Repair Instructions
This informational bulletin provides information on control module diagnostics and configuration, programming using the TIS Service Programming System (SPS), set-up and warranty.
10-08-45-001E
Service Bulletin/Repair Instructions
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with conductive finish.
PI1394
Service Bulletin/Repair Instructions
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
PIT3271G
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
PIC3278F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
PIC4310K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
03-00-91-001G
Service Bulletin/Repair Instructions
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
030848006J
Service Bulletin/Repair Instructions
This informational bulletin provide information for the technicians to repair the rear window defroster contact or tabs.
1008110001C
Service Bulletin/Repair Instructions
This information provides the proper way to install the floor mats .
PIT5353
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles. A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
PIP5029F
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.
PIT5264B
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
11-00-89-005H
Service Bulletin/Repair Instructions
This warranty bulletin clarifies the use of dealer empowerment to satisfy the customer.
13-00-89-004J
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
14350D
Service Bulletin/Repair Instructions
Unintended Ignition Key Rotation
PIT5099A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
PIP5232A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
07-08-49-020I
Service Bulletin/Repair Instructions
This informational bulletin provides a quick guide to updating which model vehicle after replacing the IPC.
PIT5264A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States. While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
PIC6036
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that show an error message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
PIP5232
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIP5226
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
10-08-110-001B
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to use floor mats.
10-00-89-006E
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
14350A
Service Bulletin/Repair Instructions
Unintended Ignition Key Rotation
14350B
Service Bulletin/Repair Instructions
Unintended Ignition Key Rotation
PIT3099M
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PIC4310J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
00-06-01-012E
Service Bulletin/Repair Instructions
This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool.
PIP5163A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
00-00-89-027H
Service Bulletin/Repair Instructions
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a vehicle.
10-00-89-006D
Service Bulletin/Repair Instructions
This information bulletin provides the dealers on how to submit a product information report.
Recalls
Service Bulletin/Repair Instructions
Vehicle Recalls
PIC5088E
Service Bulletin/Repair Instructions
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
PIC5588B
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
05-08-46-006S
Service Bulletin/Repair Instructions
This informational bulletin advises the technician to update the Onstar from an analog system to a digital system if the customer wishes.
13-00-89-004I
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
05-06-04-035D
Service Bulletin/Repair Instructions
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
01-08-42-001J
Service Bulletin/Repair Instructions
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
02-08-42-001G
Service Bulletin/Repair Instructions
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
PIT3099L
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
PI1217
Service Bulletin/Repair Instructions
This preliminary bulletin provides a way to aid the technician in diagnosing transmission fluid leaking from the trans breather vent.
13-00-89-004H
Service Bulletin/Repair Instructions
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
13-00-89-004G
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT5264
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
PIT4864F
Service Bulletin/Repair Instructions
Information On Requests To Add OnStar Bluetooth Option.
PIC3011H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
13-00-89-004F
Service Bulletin/Repair Instructions
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that may be un necessary.
PIT4943C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
PIC5453A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
99-08-51-007F
Service Bulletin/Repair Instructions
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
PIC5953
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
PIP3140F
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PI0281D
Service Bulletin/Repair Instructions
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
10-00-89-006C
Service Bulletin/Repair Instructions
This informational bulletin provides directions on submitting different PIRs
13-00-89-004E
Service Bulletin/Repair Instructions
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
05-00-89-072C
Service Bulletin/Repair Instructions
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.
13-00-89-004D
Service Bulletin/Repair Instructions
This informational bulletin provides an update for 13-00-89-004C to include updated information.
04-06-04-047L
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047K to add the 2014 model year.
05-06-04-022J
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 04-06-04-047 to add the 2014 model year.
10-08-110-001A
Service Bulletin/Repair Instructions
This informational Bulletin provides a revision for 10-08-110-001 to add the 2012-2014 model years.
PIP5163
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
PIT3099K
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
130089009
Service Bulletin/Repair Instructions
Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
PIC5904
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
06-06-01-010B
Service Bulletin/Repair Instructions
This informational bulletin provides information on close-coupled converter and engine replacement.
00-03-10-003R
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information new tire warranty program and global warranty management submission information.
10-00-89-010C
Service Bulletin/Repair Instructions
This informational bulletin provides information on key codes security rules and information on GM key code look up application.
10-00-89-009B
Service Bulletin/Repair Instructions
This informational bulletin provides information on key code security and information on GM key code look up applications.
07-08-49-020H
Service Bulletin/Repair Instructions
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
PI-0011A
Service Bulletin/Repair Instructions
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
02-07-30-052I
Service Bulletin/Repair Instructions
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096 TransFlow.
08-06-01-006D
Service Bulletin/Repair Instructions
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
11-00-89-005E
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.
02-08-98-002D
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
09-00-89-008A
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.
05-08-48-001C
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.
13-00-89-004B
Service Bulletin/Repair Instructions
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
PIT4720C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
13-00-89-005
Service Bulletin/Repair Instructions
This technical bulletin provides Warranty Administration - New Labor Codes information.
99-04-20-002H
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
13-00-89-004
Service Bulletin/Repair Instructions
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
11-00-89-005D
Service Bulletin/Repair Instructions
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.
10-00-89-017Z
Service Bulletin/Repair Instructions
This informational bulletin provides information on fix it right for first time issues.
00-03-10-002G
Service Bulletin/Repair Instructions
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.
PIP3140E
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
PIP5094
Service Bulletin/Repair Instructions
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
08-08-51-002A
Service Bulletin/Repair Instructions
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
11-00-89-005C
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm
PIC3718E
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
PIT3173C
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
10-00-89-017X
Service Bulletin/Repair Instructions
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to find growing concerns around them.
080846004A
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.
08-08-44-015C
Service Bulletin/Repair Instructions
This informational bulletin provides information regarding the inappropriate warranty claims submitted for damaged radios and instrument panel clusters, provides exampls on whats an acceptable for warranty and whats not
000089027G
Service Bulletin/Repair Instructions
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC4310H
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
06-00-89-026J
Service Bulletin/Repair Instructions
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
100089010B
Service Bulletin/Repair Instructions
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
010089010J
Service Bulletin/Repair Instructions
This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.
10-00-89-017W
Service Bulletin/Repair Instructions
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
100089017W
Service Bulletin/Repair Instructions
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so that vehicles can be fixed right the first time in for service.
PIT4907A
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
PIC4935D
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
PIT3099J
Service Bulletin/Repair Instructions
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
11-00-89-005B
Service Bulletin/Repair Instructions
This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm
10-00-89-017V
Service Bulletin/Repair Instructions
This informational bulletin provides information on newly release bulletins used to fi the vehicles in the field the first time.
PIC5588A
Service Bulletin/Repair Instructions
Programming And Activation Of Replacement OnStar Modules.
09-09-40-001A
Service Bulletin/Repair Instructions
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
PIP-4492P
Service Bulletin/Repair Instructions
BUICK/CADILLAC/CHEVROLET/GMC/HUMMER/PONTIAC/SAAB: OIL CONSUMPTION AND/OR EXHAUST SMOKE-POSSIBLE PCV BAFFLE OR LIFTER CONCERN. UPON INSPECTION, OBVIOUS OIL WILL BE FOUND IN THE INTAKE MANIFOLD AND/OR PCV VACUUM TUBE. *PE UPDATED 3/21/11. *PE UPDATED 5/9/11. *PE UPDATED 5/25/11. *PE UPDATED 06/16/2011. *KB UPDATED A SECOND TIME ON 06/16/2011. *KB UPDATED 6/27/11. *PE
08089-B
Service Bulletin/Repair Instructions
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
08-089B
Service Bulletin/Repair Instructions
BUICK CHEVROLET GMC SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. CSC LETTER WAS RECEIVED. *PE
08-089
Service Bulletin/Repair Instructions
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
01-02-32-001
Service Bulletin/Repair Instructions
CONCERNS WITH CLUNK NOISE FROM FRONT OF VEHICLE TURNING MANEUVER / STEERING WHEEL ROTATION.*JB (LUBRICATE OR REPLACE INTERMEDIATE SHAFT AS APPROPRIATE). UPDATED 10/05/07. *NJ UPDATED 4/1/08. *NJ UPDATED 7/1/2008 *PE
080730002
Service Bulletin/Repair Instructions
INFORMATIONAL ON 4T65-E MN7, M15 AND M76 FRONT WHEEL DRIVE AUTOMATIC TRANSMISSION VALVE BODY RECONDITIONING, DTCS P0741, P0742, P0757, P842, HARSH SHIFTS OR SLIPS. *PE
08-07-30-002
Service Bulletin/Repair Instructions
INFORMATION ON 4T65-E MN7, M15 AND M76 FRONT WHEEL DRIVE AUTOMATIC TRANSMISSION VALVE BODY RECONDITIONING, DTCS P0741, P0742, P0757, P842, HARSH SHIFTS OR SLIPS. *PE UPDATE 6/11/10. *PE
070139002
Service Bulletin/Repair Instructions
EI07091 - A/C NOT COLD ENOUGH, HVAC MODE DOESN'T CHANGE, HEAT NOT HOT ENOUGH, B0409, B0419, B0269, B0249, B0408, B0268, B0418, B0248, B0414, B3749, B0424, B3748 (ACTUATOR DIAGNOSIS) *NJ
060232009
Service Bulletin/Repair Instructions
OVERVIEW OF STEERING SYSTEM NOISES. *NJ
030604030
Service Bulletin/Repair Instructions
MULTIPLE DRIVEABILITY SYMPTOMS OF LONG OR HARD STARTS, CHUGGLE, ROUGH IDLE AND LIGHT OR INTERMITTENT MISFIRE DUE TO CLOGGED FUEL INJECTORS. *TT
060730023
Service Bulletin/Repair Instructions
4T65E TRANSMISSION 1-2 SHIFT SHUDDER AT LIGHT TO MODERATE ACCELERATION. REPLACE COMPLETE SECOND CLUTCH ASSEMBLY. *KB
060235005
Service Bulletin/Repair Instructions
KEY STUCK IN IGNITION, KEY WILL NOT RETURN TO OFF POSITION, SHIFTER BUTTON WON'T RELEASE IN PARK POSITION. *TT
010232001F
Service Bulletin/Repair Instructions
CLUNK FELT/NOISE HEARD FROM STEERING COLUMN, STEERING GEAR AND/OR FRONT OF VEHICLE DURING TURNING MANEUVER AND/OR STEERING WHEEL ROTATION. *TT
040235004D
Service Bulletin/Repair Instructions
CLUNK NOISE FROM FRONT OF VEHICLE DURING TURNING MANEUVER/STEERING WHEEL ROTATION. *TT *NM
050232007
Service Bulletin/Repair Instructions
POWER STEERING MOAN OR GROAN NOISE WHILE DRIVING. *JB
040604066A
Service Bulletin/Repair Instructions
CLUNK/BANG FROM REAR OF VEHICLE. *TT
050604058
Service Bulletin/Repair Instructions
INTERMITTENT CHUGGLE OR FISHBITE ON LIGHT ACCELERATION OR A HIGHWAY SPEEDS WITH NO DIAGNOSTIC TROUBLE CODES (DTCS). *TT
050846006A
Service Bulletin/Repair Instructions
INFORMATION ON UPGRADING CERTAIN ONSTAR GENERATION 5 ANALOG/DIGITAL-READY SYSTEMS TO ONSTAR GENERATION 6 DUAL-MODE (ANALOG/DIGITAL). *TT
709
Service Bulletin/Repair Instructions
TIE ROD SPECIFICATIONS REVISED. GM TECH LINK. *TT
040523002
Service Bulletin/Repair Instructions
BRAKE ROTOR MINIMUM ALLOWABLE THICKNESS AFTER REFINISH SPECIFICATION CORRECTION. *TT
050232003
Service Bulletin/Repair Instructions
REVISED OUTER TIE ROD END NUT TIGHTENING SPECIFICATION/TIE ROD END JAM NUT TIGHTENING SPECIFICATION ADDED. *TT
020730013D
Service Bulletin/Repair Instructions
INCORRECT TRANSMISSION SHIFTS POOR ENGINE PERFORMANCE HARSH 1-2 UPSHIFTS SLIPS 1ST AND REVERSE TORQUE CONVERTER CLUTCH STUCK OFF ON DIAGNOSTIC TROUBLE CODE P0730, P0756, P0757, P0741, P0742. *EH *TT
030848005A
Service Bulletin/Repair Instructions
COMPASS ZONE ADJUSTMENT AND CALIBRATION PROCEDURE DURING PRE-DELIVERY INSPECTION. VARIOUS MODELS INCLUDING 2002-2004 LIGHT DUTY TRUCKS. *TT UPDATE TO INCLUDE 2005 BUICK ALLURE. *TT
702
Service Bulletin/Repair Instructions
INSTRUMENT PANEL (I/P) APPEARANCE. GM TECH LINKS. *TT
030844005B
Service Bulletin/Repair Instructions
POOR RADIO RECEPTION OR RADIO STATIC/ INCREASED INTERFERENCE WITH REAR WINDOW DEFOGGER ON OR SOME REAR WINDOW DEFOGGER GRIDS MAY BE INOPERATIVE. *TT
040857007
Service Bulletin/Repair Instructions
HEADLINER WET AROUND SUN ROOF. *EH
050604002
Service Bulletin/Repair Instructions
WHISTLE NOISE ON LIGHT ACCELERATION. *EH
030849018B
Service Bulletin/Repair Instructions
BROKEN CONSOLE OR STORAGE COMPARTMENT LID LATCH. *TT UPDATED *EH
040867008
Service Bulletin/Repair Instructions
SUNROOF CREAK. *TT
040847003
Service Bulletin/Repair Instructions
SECURITY LIGHT ON, ENGINE WILL NOT CRANK, DIAGNOSTIC TROUBLE CODES B2958 AND/OR B2960. *TT
0804
Service Bulletin/Repair Instructions
OIL LIFE SYSTEM RESET PROCEDURES - CARS. *NM
07142004
Service Bulletin/Repair Instructions
INCORRECT PARTS INFORMATION FOR SERVICING THE CONSOLE LID OR STORAGE ARMREST ASSEMBLY. *EH
07082004
Service Bulletin/Repair Instructions
GM SERVICE TECHNICAL COLLEGE. *EH
040138009
Service Bulletin/Repair Instructions
POOR A/C PERFORMANCE - A/C WILL NOT BLOW COLD ENOUGH, RECIRCULATION MODE DOOR INOPERATIVE, DIAGNOSTIC TROUBLE CODES (DTCS) B0268 AND B0269 SET. *TT
040850011
Service Bulletin/Repair Instructions
REPAIRING NAPPED SEAT FABRIC. *EH
06282004
Service Bulletin/Repair Instructions
LEFT AND RIGHT FRONT WHEEL ASSEMBLIES IN WHICH THE TWO BOLTS THAT ATTACH THE FRONT BRAKE CALIPER TO THE STEERING KNUCKLE WERE NOT TIGHTENED ADEQUATELY. CAMPAIGN 04094 IS SCHEDULED. *TT
040308010
Service Bulletin/Repair Instructions
CHANGES TO LABOR TIME GUIDE RELATING TO FRONT SUSPENSION LABOR OPERATIONS COMPONENTS. *EH
040601017
Service Bulletin/Repair Instructions
NEW UPPER INTAKE MANIFOLD AND GASKET KITS. *TT
040601021
Service Bulletin/Repair Instructions
NEW REAR MAIN SEAL AND SPECIAL TOOL FOR INSTALLATION. *TT
030849018A
Service Bulletin/Repair Instructions
CONSOLE LID OR STORAGE ARMREST LATCH REPLACEMENT. *TT
04132004
Service Bulletin/Repair Instructions
THIS MESSAGE IS IN REGARD TO THE ELIMINATION OF THE TRUNK LID ASSIST HANDLE. CHANGES IN THE TRUNK LID HINGE AND STRUT DESIGN HAS RESULTED IN IMPROVEMENTS IN THE TRUNK LID EFFORTS. GM VOICEMAIL EXPRESS. *TT
04082004
Service Bulletin/Repair Instructions
THE CURRENT BRAKE ROTOR MINIMUM ALLOWABLE THICKNESS AFTER REFINISH, OR MINIMUM THICKNESS SPECIFICATION, FOUND IN THE PAST SERVICE MANUAL APPLICATIONS ARE INCORRECT. PLEASE USE CORRECT INFORMATION AS FOLLOWS. *TT
040730010
Service Bulletin/Repair Instructions
REVISED CASE SIDE COVER REPLACEMENT PROCEDURE. *TT
040852001
Service Bulletin/Repair Instructions
SETUP PROGRAMMING BCM FOR REMOTE KEYLESS ENTRY. *EH
01232004
Service Bulletin/Repair Instructions
TRANSMISSION FLUID LEAK FROM REVERSE SERVO COVER AT AMBIENT TEMPERATURES. TRANSMISSION FLUID MAY BE DETECTED ON THE LOWER PAIN RAIL OR CASE SIDE. MOST LEAK REPORTS HAVE BEEN FOUND DURING PREDELIVERY INSPECTION. GM VOICEMAIL EXPRESS. *TT
00351
Service Bulletin/Repair Instructions
REMOTE KEYLESS ENTRY INOPERATIVE AFTER BODY CONTROL MODULE (BCM) REPLACEMENT. *TT
00372D
Service Bulletin/Repair Instructions
ONSTAR SYSTEM IS ATTEMPTING AND/OR COMPLETING PHONE CALLS WHICH THE OPERATOR OF THE VEHICLE DID NOT INITIATE. *TT
01353
Service Bulletin/Repair Instructions
ENGINE MISFIRE DUE TO INJECTOR FRETTING CORROSION. *TT
01382C
Service Bulletin/Repair Instructions
SECURITY INDICATOR RELATED CONCERN. SERVICE VME--VEHICLES WANTED. *TT
01505
Service Bulletin/Repair Instructions
LOOSE FUEL CAP MESSAGE AND DIAGNOSTIC TROUBLE CODE (DTC) P0440, P0455. *TT *MJ
01527
Service Bulletin/Repair Instructions
A WHISTLE TYPE NOISE COMING FROM THE ENGINE. SIT BULLETIN 1406534. *TT
01583
Service Bulletin/Repair Instructions
ENGINE WIRING HARNESS CAUSING MULTIPLE DRIVEABILITY CONCERNS DIAGNOSTIC TROUBLE CODES (DTCS). *TT *MJ
01611
Service Bulletin/Repair Instructions
RUSTY OR CORRODED APPEARANCE ON UNDERCARRIAGE COMPONENTS. *TT
01614
Service Bulletin/Repair Instructions
RUSTY OR CORRODED APPEARANCE ON UNDERCARRIAGE COMPONENTS.*MR
01662
Service Bulletin/Repair Instructions
XM ERROR ON A RADIO DISPLAY. *TT
01670
Service Bulletin/Repair Instructions
INCORRECT PCM (POWERTRAIN CONTROL MODULE) PART NUMBER SETTING DTC (DIAGNOSTIC TROUBLE CODE) P0135. *TT
01715
Service Bulletin/Repair Instructions
4T65E TRANSMISSION FLUID LEAK FROM THE REVERSE SERVO COVER IN COLD WEATHER. *TT
01726
Service Bulletin/Repair Instructions
IPC, TACHOMETER, SPEEDOMETER, GAUGE NEEDLE NOISE. SIT BULLETIN 1457611. *TT
01740
Service Bulletin/Repair Instructions
CROSS INJECTOR WIRES CAUSING MISFIRE AT STEADY STATE SPEED AND RPM, MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATED, AND A P0300 SET. SIT BULLETIN 1460291. *TT
01759
Service Bulletin/Repair Instructions
XM RAPID ACTIVATION UTILIZATION. *MR
01970
Service Bulletin/Repair Instructions
SIR DISABLE. ALSO INCLUDING 2005 CHEVROLET IMPALA AND MONTE CARLO. *MR
02035
Service Bulletin/Repair Instructions
ELIMINATION OF TRUNK LID ASSIST HANDLE. *MR
02038
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODE B1000. *MR
02100
Service Bulletin/Repair Instructions
NO XM BAND AFTER RADIO REPLAC/REPAIR OR LOW VOLUME ON XM. *MJ
02130
Service Bulletin/Repair Instructions
CONSOLE OR STORAGE ARMREST LID LATCH REPAIR. SERVICE VME. *TT
3002
Service Bulletin/Repair Instructions
UNABLE TO PROGRAM NEW BODY CONTROL MODULE (BCM). *MJ
3006
Service Bulletin/Repair Instructions
ENGINE MECHANICAL NOISE. VARIOUS MODELS INCLUDING THE 2005 PONTIAC GRAND PRIX. *TT
3007
Service Bulletin/Repair Instructions
3.8L ENGINE OIL CONSUMPTION. *TT
3009
Service Bulletin/Repair Instructions
SERVICE VME - IP TOP PAD TO TRIM PLATE GAP. *MJ
3011
Service Bulletin/Repair Instructions
WHEN USING VOICE RECOGNITION DIALING, SOME NUMBERS OR COMMANDS MAY NOT BE UNDERSTOOD BY THE SYSTEM ESPECIALLY THE NUMBER TWO (2). *TT
3043
Service Bulletin/Repair Instructions
INTERMITTENT SECURITY LAMP ON. DIAGNOSITC TROUBLE CODE B2958 OR B2960 MAY OR MAY NOT BE PRESENT. *TT
3074
Service Bulletin/Repair Instructions
PERFORMANCE OF XM RADIO SYSTEM WITH SUNROOF FULLY OPEN. *TT
3097
Service Bulletin/Repair Instructions
HVAC SIDE TO SIDE TEMPERATURE DIFFERENCE. *SC
3101
Service Bulletin/Repair Instructions
INOPERATIVE A/C VENT LOUVERS. *JB
3104
Service Bulletin/Repair Instructions
GAP APPEARANCE BETWEEN THE I/P TOPPER PAD AND I/P TRIM PLATE. *SC
3106
Service Bulletin/Repair Instructions
XM RADIO WAS WORKING PRIOR TO JULY 26, 2004 AND IT IS INOPERATIVE NOW. *JB
3129
Service Bulletin/Repair Instructions
A/C EVAPORATOR FREEZING. *TC
01382A
Service Bulletin/Repair Instructions
SECURITY INDICATOR RELATED CONCERN - CARS WANTED UNTIL OCTOBER 31. SERVICE VME. *TT
01390
Service Bulletin/Repair Instructions
XM RADIO MUST BE TUNED TO CHANNEL 1 THROUGH 66 DURING ACTIVATION ATTEMPT. 2004 CHEVROLET CANYON, GMC DENALI, GMC COLORADO ALSO INCLUDED. *TT
11052003
Service Bulletin/Repair Instructions
DIAGNOSTIC TROUBLE CODES P0440 AND P0455, ALONG WITH A LOOSE FUEL CAP MESSAGE DISPLAYED ON THE DIC ON VEHICLES WITH 3800 ENGINE APPLICATIONS. *TT
020730022B
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT
010232001C
Service Bulletin/Repair Instructions
SOME CUSTOMERS MAY COMMENT ON A CLUNK TYPE NOISE COMING FROM THE FRONT OF THE VEHICLE DURING A TURNING MANEUVER. *TT
020861001A
Service Bulletin/Repair Instructions
CLICKING/CREAKING NOISE FROM FRONT OF VEHICLE. *TT
081203
Service Bulletin/Repair Instructions
THIS SERVICE VOICEMAIL MESSAGE OUTLINES A METHOD TO ATTEMPT REPAIR OF THE AIR CONDITIONER VENT LOUVER BEFORE REPLACING THE ENTIRE TRIM PLATE. *TT
030730029
Service Bulletin/Repair Instructions
CHANGES FOR 2004 MODEL YEAR FOR 4T65E TRANSAXLE - INTERNAL CHANGES TO VALVE BODY, SPACER PLATE AND CHANNEL PLATE AND TOUCH ACTIVATED POWER (TAP). *TT
01432
Service Bulletin/Repair Instructions
AUTOMATIC TRANSMISSION POOR ACCELERATION, PERFORMANCE. *TT
01444
Service Bulletin/Repair Instructions
XM DEALER ASSISTANCE LINE INFORMATION. *TT
020861001
Service Bulletin/Repair Instructions
SOME OWNERS MAY COMMENT ABOUT A CLICKING / CREAKING TYPE NOISE COMING FROM THE FRONT OF THE VEHICLE. *TT
3064
Service Bulletin/Repair Instructions
DELAYED CRANK, MAY BE NECESSARY TO HOLD KEY IN START SEVERAL SECONDS UNTIL START. *TT
3089
Service Bulletin/Repair Instructions
SERVICE ENGINE SOON LIGHT AND REDUCED ENGINE POWER WITH A DIAGNOSTIC TROUBLE CODE P1516. DIAGNOSTIC TROUBLE CODES P0120, P0220, P1514, P1515, P1518 AND P2135 MAY ALSO BE PRESENT. *TT
3102
Service Bulletin/Repair Instructions
SERVICE VME 01-04 VEHICLE EQUIPPED WITH 4T65E AUTOMATIC TRANSMISSION 4T65E TRANSMISSION VALVE BODY INSPECTION PROCEDURE. (TO INCLUDE 2004 PONTIAC AZTEC) *SC ALL 2001 - 2006 PASSENGER VEHICLES WITH 4T65E TRANSAXLE. *TT
3157A
Service Bulletin/Repair Instructions
ENGINE WHINE OR BUZZ NOISE SOUNDS LIKE A GENERATOR TYPE NOISE ON 3.1L OR 3.8L ENGINES. *TT
3160
Service Bulletin/Repair Instructions
NOISY OR INOPERATIVE A/C COMPRESSOR. *TT
3170E
Service Bulletin/Repair Instructions
IPC, INTERIOR LIGHTS AND/OR HEADLAMPS FLICKER. *AK FB2
3296
Service Bulletin/Repair Instructions
DRIVE SPROCKET SUPPORT BEARING MISSING OR DTC P0741 AND P0742. *SC
3354
Service Bulletin/Repair Instructions
ENGINE WIRING HARNESS CAUSING MULTIPLE DRIVEABILITY CONCERNS. *EH
3365A
Service Bulletin/Repair Instructions
TICKING OR KNOCKING NOISE CRACKED OR BROKEN FLEXPLATE. VARIOUS MODELS INCLUDING OLDSMOBILE BONNEVILLE 2006. *TT
3382
Service Bulletin/Repair Instructions
4T65E (MN7) TRANSMISSION FLUID LEAK ON RIGHT SIDE AXLE SEAL. *TT
3477
Service Bulletin/Repair Instructions
TECH 2 DISPLAYS ASTERISK FOR THE LEFT FRONT WHEEL SPEED SENSOR. *TT
3500
Service Bulletin/Repair Instructions
ABS LIGHT ON AND POSSIBLE DIAGNOSTIC TROUBLE CODES. *AK
3583
Service Bulletin/Repair Instructions
ABS LAMP ON AND CURRENT OR HISTORY DTCS C1233, C1224, C1227, C1228, C1234, AND/OR C1235. *TT
3692
Service Bulletin/Repair Instructions
TICKING OR KNOCKING NOISE, CRACKED OR BROKEN FLEXPLATE. *TT
3820B
Service Bulletin/Repair Instructions
TACHOMETER AND TEMPERATURE GAUGE INOPERATIVE AFTER IPC SETUP. *AK
3853
Service Bulletin/Repair Instructions
ABS LAMP ON AND CURRENT OR HISTORY DTCS C1223, C1224, C1227, C1228, C1234, AND/OR C1235. *TT
4043
Service Bulletin/Repair Instructions
HORNS HAVING POOR QUALITY OR BECOMING INOPERATIVE AS A RESULT OF WATER INGESTION. *TT
4615
Service Bulletin/Repair Instructions
ABS PUMP RUNNING WHEN NOT NEEDED. *NJ
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.