U67 Combo Rev11
Warranty Program/Extension
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
U67 Combo Rev11
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
103954
ACTUATOR - A/C AND HEATER
104087
ACTUATOR - A/C AND HEATER
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
U67 Combo Rev10
Emissions recal U67 Catalytic Converter Efficiency
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
U67
Some of the above-involved vehicles may exceed NOx (Oxides of Nitrogen) emission level standards due to loss of catalytic converter efficiency
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004206
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004330
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
3100121
Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2121000005
62TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair
71055
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. B)
70316
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. A)
69912
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2010-2018 Dodge Journey (JC) and 2010-2014 Dodge Avenger/Chrysler 200 (JS)
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1121000006 Rev.
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
S1121000006RevA
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
9004268
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1508000480
Speed Control Operates Intermittently
18-058-19 REV. B
No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003735
Cam Phasers, Oil Control Valve For Malfunction Indicator Light (MIL) issues related to 2012-2017 3.6L Pentastar engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
1810216
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: U0140 - Lost Communication With Body Control Module. P0441 - EVAP Purge System Performance. P0420 - Catalyst Efficiency (Bank 1). P0430 - Catalyst Efficiency (Bank 2). P0133 - O2 Sensor 1/1 Slow Response. P0153 - O2 Sensor 2/1 Slow Response. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P113D - O2 Sensor 1/1 Slow Response (High Frequency). P113E - O2 Sensor 2/1 Slow Response (High Frequency). P0108 - Manifold Absolute Pressure Sensor Circuit High. P0606 - Internal Control Processor. P0204 - Fuel Injector 4 Circuit/Open.In addition, the customer may notice the following conditions: 1 - 2 upshift clunk or bump. 4 - 5 upshift clunk or bump. 5 - 6 upshift clunk or bump. 6 - 5 downshift clunk or bump. 6 - 4 downshift clunk or bump. RPM fluctuating or jerking feeling while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades. A less than desired idle speed after performing a hard braking maneuver.
23027
Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
23104
05182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
23137
Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
20244
CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
Volume 2, Issue
Warranty Operations Newsletter Updates from Warranty Operations
22867
Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22892
Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22958
1NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
20616
P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
55111275A
Sun Sensor Multi zone Auto Climate Control systems. Left and right outlet temperatures do not match when system is in "sync" . Occupants will experience being cold ( winter time), on either passenger or driver side, even though the temperature setting is the same. Root cause: Suspect sun senors ( PN 55111274AA and 55111275AA). THERE WILL BE NO DTC FOR THE SUN SENSOR active or stored. The issue is diagnosed by using an INCANDESCENT (not LED) shop lamp. Shine the shop lamp on the left side of the sensor, then on the right side of the sensor, while monitoring sensor output with STARSCAN. The reading should change from 0 (or near zero) to about 20 to 40. The important thing is that the left and right readings are the same, and that they change when the lamp is shone on it.
68141352A$
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
18-079-16
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience any of the following: · **Rough idle (Sales Code EDG). · A Transmission Tip-In bump (Sales Code EDG). · Hard to start in cold ambient temps. (Sales Code EDG).** · Engine idle cycling on cold start in gear (Sales Codes ED3 & EDG). · Slight engine surge driving at highway speeds (Sales Codes ED3 & EDG).
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
68175510A
Rear trailing arm/link.
68175510A$
Rear trailing arm/link. Customer noise issue due to loose trailing link If a trailing link is damaged or noisy, please call Steve Lin at Cell 909-569-5117 prior to removing the part. If you do not hear from us within 15 minutes please continue with the repair.
55113664A
Side door Upper and lower hinge, All side doors
55113664A$
Side door Upper and lower hinge, All side doors
68225378A
3.0L V6 Turbo Diesel - Sales Code EXF
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free
68206429A
Pad, Seat Cushion
68277402A
Adaptive Cruise Control Sensor
04753183A
Transmission, Oil Pump, Torque Convertor, and Flexplate
1PH98RXFA
Parts.
68037593A
Beam, Upper Load Path & Beam, Inner Load Path
68246267A
Active Grill Shutter (AGS)
68253737A
DEF Tank
05137133A
Dual Electric Fan Assembly
55372070A
Mirror, Outside Rearview
68302824A
Auxiliary Lamp, Outside Mirror
68302828A
Turn Signal, Outside Rearview Mirror
68192621A
Transmission - Pan, Pan Gasket
68234120A
Panasonic 8.4" CTP/FCTP Radio, Update Failure
68234120A$
Panasonic 8.4" CTP/FCTP Radio, Update Failure
D-16-03
Can/Am Warranty coverage
D1603
Can/Am Warranty coverage
5LC23DX9A
Load Floor Handle.
68018095A
HVAC Distribution Housing
68018095A$
HVAC Distribution Housing When ordering HVAC Distribution Housing PN 68018095A$, also order Seal Kit PN68066971AA that is needed for installation. The seal kit does not come with the Distribution Housing.
68143886A
RADIATOR, Engine Cooling
68143886A$
RADIATOR, Engine Cooling
68227808A
Rear Differential or Rear Differential Actuation Motor
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
R2108213A
W5A580 (NAG1) Valve Body - complete
R2108213A$
W5A580 (NAG1) Valve Body - complete
68210304A
Fuel Tank
08-115-15
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
18-071-15
Unable to Program Keys After Wireless Ignition Node Replacement
1807115
Unable to Program Keys After Wireless Ignition Node Replacement
SB-18-071-15
2014 TOWN & COUNTRY/GRAND CARAVAN: 200/AVENGER: ORIGINAL VEHICLE KEYS DON'T FUNCTION PROPERLY AFTER REPLACEMENT OF THE WIRELESS IGNITION NODE. *CN
09-008-15
3.6L Oil Loss Diagnostic Aid This bulletin involves additional information on oil loss.
SB-09-008-15
VARIOUS VEHICLES ARE EXPERIENCING LOSS OF OIL, AND POSSIBLY AN OIL LEAKAGE POOLING IN ENGINE VALLEY AND POSSIBLY NEED REPLACING OIL FILTER HOUSING. MODEL 2014. *PE
08-038-15
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.
07-002-15 REV. A
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
18-003-15
Flash: PCM System Improvements For Hard Controlled Stops This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a less than desired idle speed after performing a hard braking maneuver.
07-002-15
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
08-112-14
Hands Free Feature Inoperative This bulletin involves updating the Hands Free Module (HFM) software. The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.
0811214
Hands Free Feature Inoperative
18-022-14 REV. A
Flash: Cold Start Engine Idle Cycling In Gear and/or Surging at Highway Speeds This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience any of the following : Engine idle cycling on cold start in gear. Slight Engine surge driving at highway speeds.
1802214
Flash: Cold Start Engine Idle Cycling In Gear and/or Surging at Highway Speeds This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience any of the following : Engine idle cycling on cold start in gear. Slight Engine surge driving at highway speeds.
1802214REVA
Flash: Cold Start Engine Idle Cycling In Gear and/or Surging at Highway Speeds This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience any of the following: Engine idle cycling on cold start in gear. Slight Engine surge driving at highway speeds.
08-086-14 REV. A
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.
0808614a
RBZ Or RHB Radio Software Enhancements
23-032-14
Headliner Falling Down - Hard Top Convertible This bulletin involves removing the headliner panels and regluing the headliner fastener brackets to the headliner panels. The fastener brackets that secure the headliner panels to the roof are separating from the headliner panels. The customer may describe the headliner falling down.
2303214
Headliner Falling Down - Hard Top Convertible
18-054-14
Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.
1805414
Intermittent Extended Crank, Long Crank Time.
08-086-14
RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).
0808614
RBZ Or RHB Radio Software Enhancements
9002503
RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
24-006-14
Poor AC Performance This bulletin involves inspecting the A/C condenser for leakage and replacing if required. The customer may experience poor A/C performance from the HVAC system due to refrigerant loss through the condenser.
2400614
Poor AC Performance This bulletin involves inspecting the A/C condenser for leakage and replacing if required. The customer may experience poor A/C performance from the HVAC system due to refrigerant loss through the condenser.
17-003-14
Rear End Creak Noise While Going Over Bumps This bulletin involves verifying the customer?s symptom/condition and if necessary, replacing the rear suspension springs. Squeak or creak noise coming from the rear of the vehicle, while going over bumps at low speeds between 5 - 20 MPH.
18-034-14 REV. A
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
18-034-14
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
SB-18-034-14
ON SOME MODEL VEHICLES AND JEEPS, (MY 2013-2014)MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES AND DIAGNOSTIC TROUBLE CODE (DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE
08-024-14
RHW RHP Radio Software Enhancements This bulletin involves upgrading the software on the RHW or RHP Radio. The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.
No83
MasterTech Updates
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
18-014-14
Flash: MIL Illumination P0204- Fuel Injector 4 Circuit/Open This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0204 - Fuel Injector 4 Circuit/Open
18-009-14
Unable to Program Keys After Wireless Ignition Node Replacement. Also Includes Automatic Oil Change Indicator Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Technicians may find that the original vehicle keys/FOBIKs do not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information.This release also includes accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.If the WIN had been replaced prior to this software update, the original keys/FOBIKs will need to be replaced.
WB-D-11-60
CHRYSLER GROUP: VEHICLE RESTRICTION PROGRAM ENTITLED ENHANCED CUSTOMER SATISFACTION (ECS), DESIGNS TO USE BOTH THE TECHNICAL SERVICE OPERATION AND CUSTOMER CARE, TO PROACTIVELY REACH OUT, TO CUSTOMERS, AND REPAIR THE CUSTOMER'S VEHICLE. *PE
18-043-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
78
STAR Center News No. 78 - Jan/Feb 2013: Instead of limiting the use of the tether anchor to 48 pounds (child weight) the new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.