9100900
Service Bulletin/Repair Instructions
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100860
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
113280
HOSE AND TUBE - EGR COOLANT
S2623000046
Calibration Requirements For The Power Sliding Door Module (PSDM).
S2623000041 REV.A
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
S2623000041
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
08-079-26 REV. A
Flash: Hybrid Control Processor (HCP) / Auxiliary Hybrid Control Processor (AHCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. ● P06E4 - Control Module Wake-Up Circuit Performance. ● P2797-00 - Auxiliary Transmission Fluid Pump Performance. ● P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. ● P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. ● P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment on one or more of the following: ● Vehicle does not start / engine does not crank. ● Extended engine cranking time when starting the vehicle. ● Engine turns on when requesting cabin heat to turn on. ● Loss of heat from the engine. ● Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. ● Vehicle will not start when it is cold (-30°C / -22°F and below). ● Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: ● Corrections to allow the vehicle to clear the permanent fault codes. This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.
112335
Warranty Newsletter – Volume 12, Issue 5
112379
ID-26-04 Rev. A Addition of 2.0L T4 Long Block or Complete Engine to the Powertrain Service Center (PTSC) Pre-Approval Program
S2623000034
Popping Clicking Noise From Power Sliding Door During Operation Open And Or Closed.
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
S2623000021
The Customer Concern Is The Power Liftgate, Wipers, Backup Lamp, Stop Lamp, Or Speaker Function Would Intermittently Not Function.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000017
Hood Ajar Message On Cluster.
S2623000015
The Customer May Notice a Popping Noise When Opening or Closing Either Sliding Door.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2602000002
Creaking/Groaning Noise Coming from The Front End
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110603
SPEAKER - NONE
110604
SPEAKER - NONE
03D Campaign
Fleet Campaign Parts Ordering Process (03D)
08-079-26
Flash: Auxiliary Hybrid Control Processor (AHCP) / **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. ● P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. ● P06E4 - Control Module Wake-Up Circuit Performance. ● P2797-00 - Auxiliary Transmission Fluid Pump Performance. ● P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. ● P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. ● P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment on one or more of the following: ● Vehicle does not start / engine does not crank. ● Extended engine cranking time when starting the vehicle. ● Engine turns on when requesting cabin heat to turn on. ● Loss of heat from the engine.** ● Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. ● Vehicle will not start when it is cold (-30°C / -22°F and below). ● Heard and/or felt bump when the gas engine turns on while driving. This software release includes the following software enhancement: ● Corrections to allow the vehicle to clear the permanent fault codes. , Special Tools and Policy sections, new LOP, updated Claims Data information and an updated Repair Procedure.
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
21-014-26
Internal Transmission Wiring Connector Short And **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. ● P0A43-00 - Drive Motor A Position Sensor Circuit Intermittent. ● P0A45-00 - Drive Motor B Position Sensor 1 Circuit. ● P0C1A-00 - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ● Vehicle is in limp mode.** statement, Claims Data tables,
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
08-299-25 REV. A
High Voltage Battery Pack Replacement XT1 Warranty Extension Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0EDD-00 - Hybrid/EV Battery Pack "B" Deterioration. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. NOTE: Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage This bulletin involves replacing the high voltage battery pack.
9100735
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2524000012
High Voltage Air Conditioning Refrigerant Dye
08-299-25
High Voltage Battery Pack Replacement XT1 Warranty Extension Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0EDD-00 - Hybrid/EV Battery Pack "B" Deterioration. ● P0BBE-00 - Hybrid Battery Pack Voltage Variation. ● P1C5E-00 - Battery State Of Health Failed. NOTE: Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage This bulletin involves replacing the high voltage battery pack.
107271
D-25-16 (XT1) High Voltage Battery Pack - Select 2017 - 2021 Chrysler Pacifica/ Voyager (RU)
107277
ID-25-12 (XT1) High Voltage Battery Pack - Select 2017 - 2021 Chrysler Pacifica/ Voyager (RU)
ID-25-13
ID-25-13 (XT1) High Voltage Battery Pack - Select 2017 - 2021 Chrysler Pacifica/ Voyager (RU)
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
21-025-25 REV. A
Internal Transmission Wiring Connector Short and Motor A Bearing Failure Warranty Extension XE1 Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0A3F - Drive Motor A Position Sensor 1 Circuit. ● P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ● P0A45 - Drive Motor B Position Sensor 1 Circuit. ● P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ● Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ● Hybrid Control Processor (HCP). ● Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves servicing the transmission.
S2509000001 REV.B
Engine Rattle Noise
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
S2523000057
1st Row Armrest Not Holding Position, Being Broken, Being Too Low, Or Touching The Console.
S2523000050
Vibration From Engine Or Powertrain. Powertrain Mounting Neutralization Procedure. Discussion: Service information is in the process of being updated to include powertrain mount installation best practices. The new procedure will neutralize the mounts to lessen or remove unwanted mount tension that can lead to vibration complaints.
S2423000026 REV.A
Power Sliding Door Will Not Power Open And/Or Close Automatically.
S2509000001 REV.A
Engine Rattle Noise
104093
D-23-07 Rev. B (XE1) eFlite Si-eVT Transmission Repair – Certain 2017 - 2023 Chrysler Pacifica (RU)
104094
ID-23-07 Rev. B (XE1) eFlite Si-eVT Transmission Repair – Certain 2017 - 2023 Chrysler Pacifica (RU)
21-025-25
Internal Transmission Wiring Connector Short and Motor A Bearing Failure Warranty Extension XE1 : Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0A3F - Drive Motor A Position Sensor 1 Circuit. ● P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ● P0A45 - Drive Motor B Position Sensor 1 Circuit. ● P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ● Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ● Hybrid Control Processor (HCP). ● Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). REPAIR SUMMARY: **This bulletin involves servicing the transmission.**
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
103525
HORN AND BRACKET - NONE
S2509000001
Engine Rattle Noise
103263
RESERVOIR - COOLANT
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2223000036 REV.A
Reverse View Camera Inoperative After Recent Repair
99965
MODULE - INVERTER
100209
Warranty Newsletter Volume 10 Issue 8_ID
03-008-24
Updated Front Hub Nut Torque Specification There are no Customer Symptoms for this Information Only Technical Service Bulletin (TSB).
S2423000035
Liftgate Inoperative And Or Intermittently Will Not Open Or Close.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2423000002
2 nd Row Seat Does Not Fold Using Easy Entry Handle.
21-042-24
Internal Transmission Wiring Connector Short and Motor A Bearing Failure Warranty Extension XE1 **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0A3F - Drive Motor A Position Sensor 1 Circuit. ● P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ● P0A45 - Drive Motor B Position Sensor 1 Circuit. ● P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ● Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ● Hybrid Control Processor (HCP). ● Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.
98746
Warranty Bulletin D-23-07 Rev. A (XE1) eFlite Si-eVT Transmission – Certain 2017 - 2023 Chrysler Pacifica (RU)
98747
FCA Caribbean Warranty Bulletin ID-23-07 Rev. A (XE1) eFlite Si-eVT Transmission – Certain 2017 - 2023 Chrysler Pacifica (RU)
S2423000031
Power Sliding Door Inoperative Or Intermittently Will Not Open Or Close
S2307000002 REV.B
Suspected Engine Coolant Leak
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
82518
CHRYSLER PACIFICA (RU) MY2017-21 ELECTRIC COOLANT HEATER Part Requirement Verification
OD82484
Customer Handling Guidelines for Owners Incentive (39CN4)
08-130-21
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0AA1-00 - Hybrid/EV Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0B3C-00 - Hybrid/EV Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid/EV Battery Voltage Sense 3 Circuit Performance. P0B4B-00 - Hybrid/EV Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/EV Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/EV Battery Voltage Sense 6 Circuit Performance. P1A16-00 - Hybrid/EV Wakeup Control 3 Output Circuit/Open. P1D7B-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Battery. P1D7C-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Ground. P1A29 - Cell Supervisory Circuit A Failure. P1A2A - Cell Supervisory Circuit B Failure. P1D3E - Internal Control Module Shut Off Test Error. U0594 - Implausible Data Received from HCP. P2BE5 - Hybrid/EV Battery Pack Current Sensor "C" Circuit Performance. B12B0-85 - Charge Temperature Indicator-Signal Above Allowable Range. Customer may also experience one or more of the following: Premature oil change message displayed on the cluster and vehicle may be running in fuel/oil refresh mode. Scheduled charging not functioning properly because the battery pack did not wake up while plugged in.
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
3100121
Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2008000081
Cruise Control Inoperative.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
08-044-20
Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processer (AHCP) Diagnostic and System Updates This bulletin involves updating the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance. P0D57-00 - Proximity Detection Circuit Performance.
S2008000013
Key Programming, Security Pin Request, Pin Invalid
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003293
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
08-107-17
Loose High Voltage Cable at the Power Inverter Module (PIM) Terminal This bulletin involves inspecting the High Voltage Interlock Loop (HVIL) connector and potentially installing a Power Inverter Module (PIM) kit. The customer may describe a loss of vehicle propulsion or a Malfunction Indicator Light (MIL) illuminated with the following Diagnostic Trouble Codes (DTCs):P0C77-00 - HV Battery System Precharge Time Too Short. P0C76-00 - Hybrid EV System Discharge Time Too Long - PIM. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0A79-00 - Drive Motor B Inverter Performance. P1AEF-00 - MCPB High Voltage Battery System Voltage High. P0AFA-00 - Hybrid-EV Battery System Voltage Low. P0EED-00 - Hybrid-EV Battery System Discharge Circuit Performance.
23-047-17
Seat Pops or Clicks After Seatback Is Adjusted This bulletin involves adjusting the recliner cable on the second row quad seats. The customer may describe after adjusting one or both of the inboard seat upper seatbacks, a pop or clicking noise can be heard.
9003735
Cam Phasers, Oil Control Valve For Malfunction Indicator Light (MIL) issues related to 2012-2017 3.6L Pentastar engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.
0810017
Flash: Instrument Panel Cluster (IPC) Enhancement This bulletin involves updating the IPC with the latest available software. Customers may experience the total "Range" displayed in the cluster is lower during cold ambient temperatures.
9003790
Valve Cover and Gasket, Left and Right Pertains to vehicles equipped with a 3.6L V6 V.V.T. Engine only: Oil leaking from the valve cover onto the O2 sensor causing faults codes P0140, P2096, P0137, P0157. Need to verify the leak source and cause (gasket pinched, out of position, rolled, or cut). Please call one of the individuals below before proceeding with the repair. Also, if possible take a picture and send it to the emails listed below. First: Scott Knaggs - Cell (313) 363-6937 scott.knaggs@facgroup.com Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair.
9003723
Amplifier Vehicles needing amplifier replacement, please call Rayyan Mohammed at Cell (248) 954-0790 prior to repair. If no response in 15 minutes, proceed with the repair.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
0804317
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Improvements This bulletin involves reprogramming the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0AA1-00 - Hybrid Battery Positive Contactor Circuit Stuck Closed (After the vehicle is turned off, it may fail to restart). P0AA6-00 - Hybrid Battery Voltage System Isolation Fault. P1E1B-00 - Hybrid-Ev Battery Side Voltage System Isolation.Under a vehicle side isolation failure which generates P0AA6, the BPCM may falsely set P1E1B (HV battery isolation failure) on key off which results in a no start condition. U11C5-00 - BPCM Lost Communication With On Board Charging Module. P1A9B-00 - Hybrid - EV Battery Temperature Sensor 1 Out Of Range High. P1AA7-00 - Hybrid - EV Battery Temperature Sensor 4 Out Of Range High.
0804417
Flash: Hybrid Control Processor (HCP) and the Auxiliary Hybrid Control Processer (AHCP) This bulletin involves a combination reprogramming of the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following DTCs have been set:P0A79-00 - Drive Motor B Inverter Performance. The software has been updated to better address this DTC. P0A78-00 - Drive A Inverter Performance. U0415-00 - Implausible Data Received From ABS. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P061B-00 - Internal Control Module Torque Calculation Performance. P26C3-00 - Internal Control Module Electronic Shifter Performance.
9003756
Rain light sensor Rain sense wipers do not operate: 1. Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.
9003357
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block. Ensure the torque on the 5 (OFA) bolts are torqued to 12nm.
9003749
RA2 Radio 5" Uconnect Before replacing this radio, make sure you can reproduce the customer issue. If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.
08-043-17 REV. A
Flash: Battery Pack Control Module (BPCM) Diagnostic and System Improvements This bulletin involves reprogramming the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0AA6-00 - Hybrid Battery Voltage System Isolation Fault. P1E1B-00 - Hybrid-Ev Battery Side Voltage System Isolation.Under a vehicle side isolation failure which generates P0AA6, the BPCM may falsely set P1E1B (HV battery isolation failure) on key off which results in a no start condition. U11C5-00 - BPCM Lost Communication With On Board Charging Module. P1A9B-00 - Hybrid - EV Battery Temperature Sensor 1 Out Of Range High. P1AA7-00 - Hybrid - EV Battery Temperature Sensor 4 Out Of Range High.
08-044-17 REV. A
Flash: Hybrid Control Processor (HCP) and the Auxiliary Hybrid Control Processer (AHCP) This bulletin involves a combination reprogramming of the HCP and the AHCP with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0A79-00 - Drive Motor B Inverter Performance. U0415-00 - Implausible Data Received From ABS. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P061B-00 - Internal Control Module Torque Calculation Performance. P26C3-00 - Internal Control Module Electronic Shifter Performance.
18-054-17 REV. A
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:U1431 - Implausible Data Received From Cruise Control Module.P24B9 - EVAP System Leak Detection Pump Pressure Sensor Circuit Range/Performance. P0300 - Multiple Cylinder Misfire. P1C64-00 - Hybrid Perf Engine Speed Below Target During Autostart.
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
08-048-17
Navigation Inoperative This bulletin involves checking if the radio's navigation feature is working and replacing the radio if needed. A customer may notice the radio?s navigation feature is inoperative.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003640
Electronic Shift Module If DTC's U11C3, U0074 are present Stored or Active, please contact Pemi Sabageh at cell (519) 300-0629 or David Dysarz at (248) 944-0310. If you do not receive a call within 15 minutes please proceed with the repair. Please return parts back to FCA Engineering if ESM is deemed non-functional after performing this TechTip
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
23027
Return: Wiring Assy - Engine You have been identified as either having stock, or have stock in transit to your dealership. Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.
23104
05182535AD - Lamp Assy ?Tail Light LT You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
23137
Inspect and Return: Trim Cover Assy - A-Pillar Rt/Lt You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.
20244
CBXDP361AA Return: Spacer Kit - Visor You have been identified as either having stock, or have stock in transit to your dealership. Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.
Volume 2, Issue
Warranty Operations Newsletter Updates from Warranty Operations
22867
Inspect and Return: Solenoid Module - Transmission You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22892
Return: Lamp Assy - CHMSL& Cargo Light You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
22958
1NT30XDVAC - Inspect and Return: Panel - Instrument Panel You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.
20616
P/N CBSZR068AA: Inspect & Return: Module Kit - Occupant Restraint You have been identified as either having stock, or have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.
68232614A$
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
1PH98RXFA
Parts.
23-012-16
Magnesium Inner Liftgate Repair And Appearance Characteristics
D-16-03
Can/Am Warranty coverage
D1603
Can/Am Warranty coverage
R2108213A
W5A580 (NAG1) Valve Body - complete
R2108213A$
W5A580 (NAG1) Valve Body - complete
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.