9100900
Service Bulletin/Repair Instructions
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
9100860
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
113280
HOSE AND TUBE - EGR COOLANT
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2623000046
Calibration Requirements For The Power Sliding Door Module (PSDM).
S2623000041 REV.A
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A
112856
HEATER - ELECTRIC COOLANT
112857
HEATER - ELECTRIC COOLANT
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
S2623000041
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000034
Popping Clicking Noise From Power Sliding Door During Operation Open And Or Closed.
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
9100801
If the vehicle comes in with any of the following P codes, please refer to the active TSBs for HCP/AHCP flash BEFORE ordering PIM P0A78 - Drive Motor A Inverter Performance. P0A79 - Drive Motor B Inverter Performance. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P0A43-00 - Drive Motor A Position Sensor Circuit Intermittent. P0A45-00 - Drive Motor B Position Sensor 1 Circuit. P0C1A-00 - Drive Motor B Torque Delivered Performance.
S2523000003 REV.A
Door Latch, Handle And Ajar Additional Service Information.
S2623000021
The Customer Concern Is The Power Liftgate, Wipers, Backup Lamp, Stop Lamp, Or Speaker Function Would Intermittently Not Function.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000017
Hood Ajar Message On Cluster.
S2623000015
The Customer May Notice a Popping Noise When Opening or Closing Either Sliding Door.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2602000002
Creaking/Groaning Noise Coming from The Front End
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110603
SPEAKER - NONE
110604
SPEAKER - NONE
03D Campaign
Fleet Campaign Parts Ordering Process (03D)
110447
WATER PUMP
110448
WATER PUMP
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
109997
ACTUATOR - TRANSFER CASE
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
S2408000114 REV.B
Instrument Panel Cluster (IPC) Displays Warning Lamps or Messages for Loss of Advanced Driver Assist System (ADAS)
9100735
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
S2508000102
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S2509000009
Engine Oil Leak
105646
MODULE - STEERING CONTROL & COLUMN
21-040-25
948TE Transmission Reaction Shaft Service Bushing Kit Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance.
9100670
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
S2218000003 REV.B
Customer complaint may include a Mil On/Check Engine Lamp On and Electronic Throttle Control (ETC) Lamp On. There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:
107211
HOSE AND TUBE - EGR COOLANT
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000017
Door speaker Inoperative or No Sound
S2509000001 REV.B
Engine Rattle Noise
S2422000001 REV.D
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
S2523000057
1st Row Armrest Not Holding Position, Being Broken, Being Too Low, Or Touching The Console.
S2523000050
Vibration From Engine Or Powertrain. Powertrain Mounting Neutralization Procedure. Discussion: Service information is in the process of being updated to include powertrain mount installation best practices. The new procedure will neutralize the mounts to lessen or remove unwanted mount tension that can lead to vibration complaints.
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
S2423000026 REV.A
Power Sliding Door Will Not Power Open And/Or Close Automatically.
S2408000114 REV.A
Instrument Panel Cluster (IPC) Displays Warning Lamps or Messages for Loss of Advanced Driver Assist System (ADAS)
S258A000013
AM Radio Static, With No Active or Stored Radio Antenna Diagnostic Trouble Codes (DTC).
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
S2509000001 REV.A
Engine Rattle Noise
103952
APPLIQUE - B & C PILLAR
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
103525
HORN AND BRACKET - NONE
S2509000002
Engine Noise
9100498 REV 1
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
S2509000001
Engine Rattle Noise
9100498
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
103263
RESERVOIR - COOLANT
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2523000003
Door Latch, Handle And Ajar Additional Service Information.
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100468
FUEL VAPOR CANISTER FILTER EVAP Fuel Filters are to be checked for restriction / blockage on a regular schedule as indicated in the Owner s Manual. If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.
9100445
Power Transfer Unit If considering PTU Assembly replacement related to DTCs C14A7-97 or C1494-92, please be aware of updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
S2223000036 REV.A
Reverse View Camera Inoperative After Recent Repair
S2422000001 REV.C
Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
100770
SWITCH AND BEZEL - FRONT DOOR
99965
MODULE - INVERTER
03-008-24
Updated Front Hub Nut Torque Specification There are no Customer Symptoms for this Information Only Technical Service Bulletin (TSB).
S2423000035
Liftgate Inoperative And Or Intermittently Will Not Open Or Close.
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2423000002
2 nd Row Seat Does Not Fold Using Easy Entry Handle.
97962
MOTOR - BLOWER WITH WHEEL
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2423000031
Power Sliding Door Inoperative Or Intermittently Will Not Open Or Close
S2307000002 REV.B
Suspected Engine Coolant Leak
S1908000050 REV.A
Checking Radio Software Level On A VP2 Radio
S2423000026
Power Sliding Door Will Not Power Open And/Or Close Automatically.
97961
BRUSH - VACUUM
S2307000002 REV.A
Suspected Engine Coolant Leak
S2408000044
HCP Stuck In Plant Mode. Red Wrench Light On, Electric Drive Modes Disabled
9100337
PUMP WATER For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S2208000020
Electric Mode Temporarily Unavailable, Cluster Message Displayed Vehicle in Fuel Oil Refresh Mode (FORM)
ReferenceY40A
Revised Customer Satisfaction Notification Y40 ? Control Module Software Updates
S248A000001
SOS and Assistance Call Not Working After Radio Exchange Unit Installed
ReferenceY40
Customer Satisfaction Notification Y40 Control Module Software Updates
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
11646
International Warranty Bulletin ID-24-01 (XN1) eFlite Si-eVT Transmission Certain 2017 - 2023 Chrysler Pacifica (RU)
9100276
Spring Front Upr - Isolator Before replacing this part. Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.
S2309000013
Verifying Camshaft Diagnosis
S2223000058
Water Leak At Upper D-pillar Or Liftgate Area
9004452
CAMERA, Rear View Prior to replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
9100224
SWITCH AND BEZEL Front Door In any case that after following the service procedures it is determined that the switch is faulty. Please do not try to open the Switch nor fix it. Just return the part and order a new one.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9004542
Rain Sensor Before replacing the rain sensor during a front windshield replacement inspect the part for part numbers. If you have part numbers; 68507366, 68483780, 68384226 or 68384225, these parts do not utilize a replaceable gel pad, only replace the sensor for a missing or damaged gel pad. For part numbers 68298334, 68298468, 68607452 or 68194700 the gel pad should be replaced during all windshield replacements and can be ordered through MOPAR, complete sensor replacement is not necessary. Contact: FCA Redacted Content for further questions If no response in 15 minutes, proceed with repair.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
9100212
PUMP Water For 2016-2024MY 3.6L Pentastar Upgrade with suspected coolant leak. PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.
S2307000002
Suspected engine coolant leak.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
S2008000132
Malfunction Indicator Lamp Illuminated. U11E9 Lost Communication With AGS. Ambient Air Temp Incorrectly Displayed. P0070 And P0073 Set for Ambient Air Temp Senso
93005
Warranty Bulletin D-22-17 - 2017 - 2023 (Current) Chrysler Pacifica (RU) and 2013 - 2016 Chrysler Town & Country/ 2013 - 2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)
93019
FCA Caribbean Warranty Bulletin ID-22-23 - 2017 - 2023 (Current) Chrysler Pacifica (RU) and 2013 - 2016 Chrysler Town & Country/ 2013 - 2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)
2100823
Internal Transmission Wiring Connector Short Warranty Extension XE1 Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
S1808000152
CEL (Check Engine Lamp) Illuminated, P057B Brake Pedal Position Sensor Performance
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
ZD7
Customer Satisfaction Notification ZD7 - Radio Software update
S2323000058
Power Sliding Door Will Not Open And Or Close.
92181
Warranty Bulletin D-22-17 - 2017-2023 (Current) Chrysler Pacifica (RU) and 2013-2016 Chrysler Town & Country/ 2013-2020 Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)
92186
FCA Caribbean Warranty Bulletin ID-22-23 - 2017-2023 (Current) Chrysler Pacifica (RU) and 2013-2016 Chrysler Town & Country/ 2013-2020 Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)
ReferenceZD7
Customer Satisfaction Notification ZD7 - Radio Software Update
BulletinA
Customer Satisfaction Notification ZD7 - Radio Software Update
S2309000002
MIL lamp-on. Engine noise, rattle. Misfire or rough running.
0700723
Water Quality When Mixed With Engine Coolant
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
9100133
ROCKER ARM ASSY - ROLLER ROCKER Case 1.- Before replacing the intake or exhaust rocker arms due to an abnormal ticking noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
9100143
PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
90217
Warranty Bulletin D-23-07 (XE1) Eflite Si-eVT Transmission - Certain 2017 ? 2023 Chrysler Pacifica (RU)
S2307000001
Customer complaint may include a coolant leak, or, a coolant leak is detected during a routine oil change inspection.
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S228A000028
Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S2123000023
The Liftgate Latch Sticks, Will Not Open, Close, Or Hard To Close Manually
S2208000138RevA
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2208000073RevA
No Start After a Flash or Powertrain Control Module (PCM), Body Control Module (BCM) Replacement
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2208000020RevA
Electric Mode Temporarily Unavailable, Cluster Message Displayed Vehicle in Fuel Oil Refresh Mode (FORM)
S228A000017
Battery Drain Suspected or "Identified" From USB or Media Hub
S2008000075RevA
No Start, Start Stop Inoperative, Cluster Message Service Start Stop System
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S228A000004RevB
Panasonic VP4R Wi-Fi New Enrollment Pause
S1708000246RevB
Security Gateway (SGW) Module Theory and Operation
S228A000004RevA
Panasonic VP4R Wi-Fi New Enrollment Pause
9004456
LATCH, Sliding Door (Right / Left) For any RU vehicle with presence of a B2500 fault code (active / stored / pending), please refer to the following steps: 1. Please verify proper functionality of both sliding doors (power or manual) through all inputs (overhead console, key fob, handle grab). 2. If sliding doors operate as expected, do NOT replace sliding door latch(es). 3. If service is required, and your Dealership is located in the Detroit Metro Area please contact FCA Redacted Content, prior to replacing any sliding door latch(es). If no response in 15 minutes, proceed with repair. 4. If possible, please provide any / all information in the repair order narrative regarding status of sliding door function (i.e, door only works manually, won't open via key fob, etc.). This includes all customer feedback as well (what exactly brought the customer into the dealer).
9004492
LATCH, Liftgate If the Power Liftgate Latch is not releasing or latching when the customer requests the gate to operate, and your Dealership is located in the Detroit Metro area, please contact FCA Redacted Content prior to replacing the liftgate latch. If no response in 15 minutes, refer to Star Online Publication S2223000021 before replacing the latch.
Y97
Customer Satisfaction Notification Y97 Hub Bolts
S2123000023RevB
The Liftgate Latch Sticks, Will Not Open, Close, Or Hard To Close Manually
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2223000032
Front Door Is Over Flush To The Sliding Door
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2008000132 RevC
Malfunction Indicator Lamp Illuminated. U11E9 Lost Communication With AGS. Ambient Air Temp Incorrectly Displayed. P0070 And P0073 Set For Ambient Air Temp Sensor
82518
CHRYSLER PACIFICA (RU) MY2017-21 ELECTRIC COOLANT HEATER Part Requirement Verification
9004505
Lithium Ion Batteries Beginning April 1, 2022, a $5,000 penalty will be assessed to dealers who return any visually damaged battery to the supplier. Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process. To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S2223000021
The Customer Has Difficulty When Opening Or Closing The Power Liftgate
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2123000005
Hands Free Sliding Door Sensors Blocked Wash Under Vehicle Message On Cluster
S2223000009
Hands Free Power Sliding Door And Or Liftgate Function Difficult To Use Or Intermittent Operation
S2108000204
Radio Lockup In The Software Installation Screen After Accepting FOTA Update (Incorrect "S2008000204" indicated on published document)
S1608000277
KeySense Feature Settings And KeySense PIN Resetting
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S1623000028
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot
9004138RevA
GRILLE, Active Shutter For a Customer Concern of Check Engine Light On and DTC U11E9- PCM Lost Communication with Active Grille Shutter (AGS) is set, please review Star Online S2008000132 for known concerns. Prior to replacing this part please call FCA Redacted Content. If no response in 15 minutes, please proceed with repair.
9004138a
GRILLE, Active Shutter For a Customer Concern of Check Engine Light On and DTC U11E9- PCM Lost Communication with Active Grille Shutter (AGS) is set, please review Star Online S2008000132 for known concerns. Prior to replacing this part please call FCA Redacted Content. If no response in 15 minutes, please proceed with repair.
S2108000170
Head unit button stuck DTC code B14DA-2A
9004138
GRILLE, Active Shutter Prior to replacing this part, please review Star Online S2008000132 for known concerns.
S1723000001
Left Hand Drivers Side Mirror Takes Longer to Defrost Or Clear Than Right Side Passenger
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2008000119
Service Hybrid Electrical System Displayed, DTC?s P0CF1, P1B71-00, Or B12B0-00
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S2108000162
High Voltage Battery Installed, New Power Pack Unit/BPCM, No High Voltage Output From Hybrid Battery, No DTC?s
S2008000132RevA
U11E9 Lost Communication With AGS (Active Grille Shutter), Malfunction Indicator Lamp (MIL) Illuminated
S2125000002
Customer complaint includes a Mil-on condition. Upon further investigation, one or more of the following fault codes may be set in the PCM:
S1723000001RevD
Left Hand Drivers Side Mirror Takes Longer to Defrost Or Clear Than Right Side Passenger
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S2108000098RevB
Radio Screen Freeze, Blank Screen And Reset
S2108000127-1
Radio Reboot Continually
S2108000130
Bubbles Or Delamination On The Radio Display
S2108000119
Apple CarPlay Malfunctioning, Does Not Launch Or Is Cutting In An Out On Wired And Wireless Connection, Radio Stuck When IPhone Is Connected
S2108000127
Radio Reboot Continually
S2118000009
Customer complains of a MIL-on condition. Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
S2108000120
Radio Volume Uncontrollable Or Changing On Its Own
S2108000098
Radio Screen Freeze, Blank Screen And Reset
S2008000011
Customer Cannot Change Cluster Display Unit Settings, Turn By Turn Distance Does Not Match The Radios Distance
S2108000107
Rolling Auto Door Locks Stopped Operating After Recent Service Repairs
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
3100121
Steering System Inspection After a Collision This bulletin documents the FCA US LLC position regarding conditions under which replacement or repair of steering system components are required.
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2018000008
Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.