Vehicle report

2014 DODGE CARAVAN

Compare every DODGE CARAVAN yearNHTSA and EPA records

Service bulletins

109 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

108463

Service Bulletin/Repair Instructions

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

108464

Service Bulletin/Repair Instructions

PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE

103617

Service Bulletin/Repair Instructions

STARTER - ENGINE

9100456

Service Bulletin/Repair Instructions

Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to RESET the AHR following the Procedure.

S1408000384

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

9100229

Service Bulletin/Repair Instructions

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

9100226

Service Bulletin/Repair Instructions

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

93023

Service Bulletin/Repair Instructions

Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)

93120

Service Bulletin/Repair Instructions

FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC

9100196

Service Bulletin/Repair Instructions

Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used

0700723

Service Bulletin/Repair Instructions

Water Quality When Mixed With Engine Coolant

1804823

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

3100122

Service Bulletin/Repair Instructions

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

9004206

Service Bulletin/Repair Instructions

Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when

S2209000004

Service Bulletin/Repair Instructions

If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.

9004509

Service Bulletin/Repair Instructions

Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

S2109000004

Service Bulletin/Repair Instructions

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

9004386

Service Bulletin/Repair Instructions

WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

S2008000113

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S2008000113 Rev.

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S1821000001

Service Bulletin/Repair Instructions

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

9004009

Service Bulletin/Repair Instructions

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

S2121000005

Service Bulletin/Repair Instructions

62TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair

S1809000007 Rev.

Service Bulletin/Repair Instructions

Customer complaint may include engine oil leak/consumption.

23-030-20 REV. A

Service Bulletin/Repair Instructions

Active Head Restraint (AHR) Inadvertent Deployment - X87 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

70324

Service Bulletin/Repair Instructions

Warranty Bulletin D-20-19 (X87) Active Head Restraint - Select 2012-2017 Dodge Grand Caravan (RT) (Rev. A)

69920

Service Bulletin/Repair Instructions

Warranty Bulletin D-20-19 (X87) Active Head Restraint - Select 2010-2017 Dodge Grand Caravan (RT)

23-030-20

Service Bulletin/Repair Instructions

2303020

Service Bulletin/Repair Instructions

9004300

Service Bulletin/Repair Instructions

Cooler line, Power steering return The clips that hold the line to the core support are not available at this time and will need to be reused. Use care when opening and re-latching clip.

S1121000006 Rev.

Service Bulletin/Repair Instructions

(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns

S1121000006RevA

Service Bulletin/Repair Instructions

(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns

S2008000093

Service Bulletin/Repair Instructions

Blind Spot Or Park Assist Warnings, False Activation

23-015-20

Service Bulletin/Repair Instructions

Disinfectant Solution Recommended for COVID-19

08-049-20

Service Bulletin/Repair Instructions

Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

18-039-20

Service Bulletin/Repair Instructions

Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season

S2019000002

Service Bulletin/Repair Instructions

Hands On Steering Wheel Message In EVIC

S1508000480

Service Bulletin/Repair Instructions

Speed Control Operates Intermittently

9004220

Service Bulletin/Repair Instructions

CABLE, Gearshift Control Prior to replacing this component, please contact FCA Redacted Content. If there is no response in 15 minutes, continue with repair.

9004022

Service Bulletin/Repair Instructions

Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

31-003-19

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

31-004-19

Service Bulletin/Repair Instructions

Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.

31-005-19

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

31-006-19

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

3100319

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

3100419

Service Bulletin/Repair Instructions

3100519

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100619

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

9003220

Service Bulletin/Repair Instructions

RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

9002706

Service Bulletin/Repair Instructions

VALVE KIT, A/C Expansion For concern of noise while AC is running, prior to replacing this part, please call Thomas Rolo at (248) 931-0484. If no response in 15 minutes, proceed with repair.

9003355

Service Bulletin/Repair Instructions

3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

9003357

Service Bulletin/Repair Instructions

Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

9003109

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

9003694

Service Bulletin/Repair Instructions

Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

9003687

Service Bulletin/Repair Instructions

Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

9003681

Service Bulletin/Repair Instructions

Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

05152029

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

24-005-16 REV. B

Service Bulletin/Repair Instructions

Blend Door Stuck In Full Heat Mode (X64 Warranty Extension) This bulletin involves re-calibrating or replacing the right side Heating, Ventilation, Air Conditioning (HVAC) Blend Door actuator. Customers may describe one or more of the following conditions: · Not being able to adjust the HVAC system temperature to their comfort level regardless of blend door/temperature setting. · Feeling hot air coming out of the right side vents.

R4880213A

Service Bulletin/Repair Instructions

Shaft - Axle Half Note: The joint between the splines on the halfshaft and the hub and bearing is an interference fit. The halfshaft nut is to be used to draw the hub and bearing onto the halfshaft splines. This is particularly true if hub and bearing is also being replaced.~

R4880213A$

Service Bulletin/Repair Instructions

68105583A

Service Bulletin/Repair Instructions

Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

68141352A

Service Bulletin/Repair Instructions

3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

68144206A

Service Bulletin/Repair Instructions

Caliper Assy - Rear Disc Brake For a broken or missing park brake lever return spring, replace only the spring PN68039257A$ as it is a serviceable part, do not replace the caliper assembly.~

68144206A$

Service Bulletin/Repair Instructions

Caliper Assy - Rear Disc Brake For a broken or missing park brake lever return spring, replace only the spring PN68039257A$ as it is a serviceable part, do not replace the caliper assembly.~

1FL68DX9A

Service Bulletin/Repair Instructions

Flipper Close Out panel The flipper panel close out located in the rear by the load floor is failing. Engineering is collecting data on the nature of these failures for future design robustness. Please contact Deepak Patil at cell (303) 802-9794 with the details (call / text (photo)/ voicemail). email - deepak.patil1@fcagroup.com. If there is no response within 15 minutes please proceed with the repair.~

1FL68DX9A$

Service Bulletin/Repair Instructions

Z5091195A

Service Bulletin/Repair Instructions

RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Z5091195A$

Service Bulletin/Repair Instructions

68277402A

Service Bulletin/Repair Instructions

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

RL108213A$

Service Bulletin/Repair Instructions

NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

R62

Service Bulletin/Repair Instructions

Reprogram HVAC ControlModule The right side blend air door on about 161,800 of the above vehicles may experience binding. This could result in the loss of the vehicle?s interior temperature control. The Heater Ventilation Air Conditioning (HVAC) control module must be reprogrammed with new software. Vehicles found with damaged actuators must have them replaced under normal warranty. All vehicles will also receive a 5 year/60,000 miles extended warranty on the affected actuators under a separate extended warranty letter.

R62 COMBO

Service Bulletin/Repair Instructions

The right side blend air door on vehicles may experience binding. This could result in the loss of the vehicles interior temperature control. The Heater Ventilation Air Conditioning (HVAC) control module must be reprogrammed with new software. Vehicles found with damaged actuators must have them replaced under normal warranty.

68268243A

Service Bulletin/Repair Instructions

Part Description: Actuator - HVAC Issue Description: Right Temp Door Actuator is stuck in full heat. When replacing the right temp door actuator on 2014, 2015, and 2016, be sure to use the new part number 68299450AA. DO NOT USE THE OLD PART NUMBER, 68238243AA. ~ All other actuators in these vehicles may be serviced using the OLD part number, 68238243AA.

24-006-15

Service Bulletin/Repair Instructions

Flash: HVAC System Improvements This bulletin involves selectively erasing and reprogramming the HVAC Module with new software. The customer may describe one or more of the following conditions: ? Feeling hot air coming out of the passenger side vents. ? HVAC system intermittently blows cold regardless of blend door/temperature setting.

18-069-15

Service Bulletin/Repair Instructions

Flash: 3.6L Powertrain Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following symptom or conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code: ? Garage shift engagements into D may be harsh at times after shutdowns of 10-30 minute duration. ? Harsh upshifts generated by backing out of the accelerator pedal. ? Harsh shifts can be felt after acceleration/deceleration driving maneuvers from a stop. ? P0606 - Internal Control Processor. ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

09-008-15

Service Bulletin/Repair Instructions

3.6L Oil Loss Diagnostic Aid This bulletin involves additional information on oil loss.

08-038-15

Service Bulletin/Repair Instructions

RBZ Or RHB Radio Software Enhancements This bulletin involves upgrading the software on the RBZ or RHB Radio. The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

08-034-15

Service Bulletin/Repair Instructions

Wire Harness Hanging Down From Rear Bumper Fascia This bulletin involves attaching the park assist and/or blind spot detection wire harness to the rear bumper fascia. The customer may describe a wire harness hanging down from the rear bumper fascia.

07-002-15 REV. A

Service Bulletin/Repair Instructions

Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

08-022-15

Service Bulletin/Repair Instructions

Service Tire Pressure System Message This bulletin involves performing a wiTECH Misc-function routine. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): ? C151D - Tire Pressure Sensor Location Undetermined. ? C1581 - Front/Rear Side Tire Pressure Sensor Location Undetermined.

08-020-15

Service Bulletin/Repair Instructions

Flash: Blind Spot Monitor System Improvements This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. The customer may experience the blind spot monitor indicator in either outside mirror maybe flashing or on continuously. On further inspection the technician will Not find any DTCs. Symptom/Condition for RT vehicles ONLY: Customer may experience that the indicator in the side view mirrors may not illuminate when there is an object on either side of the vehicle.

CHRYSLER

Service Bulletin/Repair Instructions

The customer may experience the blind spot monitor indicator in either outside mirror maybe flashing or on continuously.

SB-08-020-15

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

23-008-15

Service Bulletin/Repair Instructions

Rattle Noise From The Right Or Left Rear Sliding Door While Driving Over Bumps This bulletin involves modifying the rubber bumper located at the rear end of the rear sliding door upper track. Rattle noise that sounds like metal against metal coming from the right or left rear sliding door area while driving over bumps.

2300815

Service Bulletin/Repair Instructions

07-002-15

Service Bulletin/Repair Instructions

05-005-14 REV. A

Service Bulletin/Repair Instructions

Steering Wheel And/Or Seat Vibration - Front Brake Rotors This bulletin involves inspecting the Julian date and if necessary, replacing the front brake rotors. The customer may describe a shake and/or vibration in the steering wheel and/or the seat while driving at highway speeds without the brakes applied. This vibration may be caused by out of balance front brake rotors.

05-005-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

0500514

Service Bulletin/Repair Instructions

0500514REVA

Service Bulletin/Repair Instructions

9003104

Service Bulletin/Repair Instructions

Part Description: Mirror, Side View Issue Description: New mirror now includes a grommet on the electrical wire. If the mirror being removed from the vehicle does not have a grommet and the new mirror does, this is not an issue. Install the new mirror and grommet.

05-005-14

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

9003153

Service Bulletin/Repair Instructions

Part Description: Hinge Kit, Load Floor Issue Description: Please note that if you are looking into getting a DOOR ASSEMBLY - LOAD FLOOR part due to a damage in the hinges only then you can just order the hinges per kit PN 68257765AA.

9002503

Service Bulletin/Repair Instructions

RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

08-067-14

Service Bulletin/Repair Instructions

Liftgate Will Not Power Close This bulletin involves visually inspecting the right side liftgate pinch sensor wire harness routing and replacing the right side pinch sensor as required. Liftgate will not power closed. Some vehicles may have an incorrectly routed right side (passenger side) pinch sensor wire harness.

08-065-14

Service Bulletin/Repair Instructions

Thatcham Installation This bulletin involves the installation of the Thatcham Engine Compartment kit.

23-011-14 REV. A

Service Bulletin/Repair Instructions

Left Rear Sliding Door Weatherstrip Seal Sticks Out At Bottom Of C-Pillar Door Opening This bulletin involves replacing the left rear C-pillar cut line sliding door seal. .

23-011-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

24-004-14 REV. A

Service Bulletin/Repair Instructions

Flash: HVAC System Intermittently Blows Cold Regardless of Setting This bulletin involves selectively erasing and reprogramming the HVAC Module with new software. Customers may experience the following condition: HVAC system intermittently blows cold regardless of blend door/temperature setting.Updating the HVAC software will correct this condition.This SB includes improved software over what was originally released with SB 24-004-14.

9003118

Service Bulletin/Repair Instructions

Sliding Door Trim Panel If a contact condition with the exterior quarter panel occurs, please engage the dual lock in the center of the trim to the door inner module.

23-016-14

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

23-014-14

Service Bulletin/Repair Instructions

Sliding Door Trim Contacting Vehicle Rear Quarter This bulletin depending on production date, involves either installing or engaging an additional door panel retention point to prevent the door panel from bowing and contacting the body when the sliding door is opened. The customer may experience a door trim panel contacting the quarter panel on either side when opening either of the sliding doors.

23-013-14

Service Bulletin/Repair Instructions

Incorrect Color Door Trim Panels And/Or Overhead Console This bulletin involves visually inspecting for color mismatch and replacing the overhead console and door panels as required. Some 30th anniversary edition vehicles were built with incorrect color door trim panels and/or overhead console.

23-011-14

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

08-042-14

Service Bulletin/Repair Instructions

Flash: Dead Battery This Bulletin involves updating the Fold and Stow Module (FSM) with new software because the FSM stays awake resulting in a continuous electrical draw. The customer may experience a dead battery.

9003081

Service Bulletin/Repair Instructions

Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

24-002-14

Service Bulletin/Repair Instructions

Driver And Passenger HVAC Blower Air Temperatures Are Not The Same When ?Sync? Setting Mode Is Selected And Headlamps Always Stay On. This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

23-038-13

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

9002519

Service Bulletin/Repair Instructions

82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.