S2208000045 REV.D
Service Bulletin/Repair Instructions
Backup Camera Poor Image Quality Inspection
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100735
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
S2508000102
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S2509000009
Engine Oil Leak
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S258A000017
Door speaker Inoperative or No Sound
21-009-25 REV. C
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
14-011-25
Fuel Filler Hose Leak Customers may comment on the following: ● Fuel odor detected at the rear of the vehicle. This bulletin involves replacing the fuel filler tube clamp and fuel filler tube hose.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100570
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
S2514000001
Fuel Odor/Leakage
104523
SWITCH AND BEZEL - FRONT DOOR
21-009-25 REV. B
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
9100390 Rev 1
D Clutch Repair Kit For transmission concerns related to DTCs P0733-00, P1DA8-00, and/or P1D92-00, a repair is available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback.
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
9100489
TUBE Fuel Supply When there is fuel leakage at the Quick Connect of the Fuel Supply Line to the Fuel Pump Module, disconnect the Line and visually inspect the Fuel Supply Line at the Seal O-Ring area for any damaged Seal or contamination and mating connection or Line leakage. If the Fuel Supply Line is found to be the source of the leakage, only replace the Fuel Supply Line.
103261
SWITCH AND BEZEL - FRONT DOOR
21-009-25 REV.A
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
9100494
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100488
TUBE Fuel Filler When there is fuel leakage at the joint of the Inlet Check Valve or the joint of the Fuel Filler Tube, place a mark on the Fuel Filler Tube of the insertion depth of the Filler Hose before removing the Hose. Check the Fuel Filler Hose for delamination or potential hole(s) or damage. Check the Inlet Check Valve (ICV) for any damage. If there is no damage found on the ICV and the Fuel Filler Hose is found to have delamination or damage, replace the Fuel Filler Hose and Clamps only. Do not replace the Fuel Filler Tube and/or the Fuel Tank. Install the new Fuel Filler Hose on the Tube to the marked location
21-009-25
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100455
EXHAUST - MUFFLER AND TAILPIPE For Exhaust noise squeak during startup acceleration deceleration please do following: 1. DO NOT remove actuators 2. Verify noise by cycling EEV manually via WiTech 3. Verify noise with test drive (optional) 4. If the noise is confirmed, replace the system without removing the actuators.
21-039-24 REV. H
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
S2208000045 REV.A
Backup Camera Poor Image Quality Inspection
21-039-24 REV. G
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24 REV. F
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24 REV. E
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24 REV. D
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
S2424000008
AC Blows Warm
21-039-24 REV. C
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
100164
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
21-039-24 REV. B
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
9100390 Rev1
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits
S2421000001
No Reverse And/Or Forward Gear After D-Clutch Repair.
9100390
D Clutch Repair Kit TSB 21-039-24 REV A - D-Clutch repair kit missing Carrier Output Shaft Seals It has been identified the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.
S2408000066
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
98931
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
98933
PUMP – WATER & CONNECTOR - OIL COOLER TUBE
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
21-039-24 REV. A
D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
21-039-24
D Clutch Repair Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch.
9100338REV1
GENERATOR Engine Prior to alternator/generator removal: 1. Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section "System Operation - Smart Charging System". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC.
S1908000050 REV.A
Checking Radio Software Level On A VP2 Radio
S2308000151 REV. A
Key Fob Battery Low Warning Message Displayed on The Instrument Panel Cluster (IPC)
08-019-24 REV. B
Security Alarm Falsely Activates Customers may experience one or more of the following: ● Alarm going off randomly at night. ● Alarm going off at parking lots. ● Tilt function not working properly. This bulletin involves performing a Restore Vehicle Configuration and updating the ITM with the latest available software.
9100344
VALVE BODY & CONTROL UNIT Transmission Ensure clutch pressure check has been completed and documented prior to valve body replacement.
0802824
Radio Over The Air Update from QR39.82F to QR40.12 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802624
Radio Over The Air Update from QR39.5 to QR40.11 Software Version Customer may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.
0802524
Radio Over The Air Updating to QR40.12 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.
Reference83A
Emission Recall 83A Sales Code Alignment
0801924
Security Alarm Falsely Activates Customers may experience one or more of the following: ? Alarm going off randomly at night. ? Alarm going off at parking. ? Tilt function not working properly. This bulletin involves performing a Restore Vehicle Configuration and updating the ITM with the latest available software.
2100424
Flash: Transmission Control Module (TCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P0729-00 - Automatic Transmission 6th Gear Incorrect Ratio. The customer may also experience one or more of the following: ? Vehicle is in limp mode. ? Rough shift. This bulletin involves reprogramming the TCM with the latest available software.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2308000151
Key Fob Battery Low Warning Message Displayed on The Instrument Panel Cluster (IPC)
0824523
Radio Over The Air Update to Q339.3 to QR39.62 Software Version Customers may experience one or more of the following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.
S2308000146
Power Door Locks Passenger Rear Door Inoperative or Door Ajar Lamp on Passenger Rear Door
S2323000082
Smart Glass Window Function Inoperative. Window Will Not Lower/Raise When Door Is Opened Or Closed, Diagnostic Trouble Code (DTC) B25B4-2A Pawl Switch Stuck.
9100264
PSU Oil Pump Assy
9100263
Dynamic Sensor Prior to replacing this part, please ensure all the pre-diagnostic & diagnostic procedures have been completed with emphasis on wiring and connector integrity. If codes C006A-28, U0125-00, or C006A-46 are present, warranty analysis suggests a high likelihood of an intermittent connection at or near the wiring connector, especially if the vehicle is a pursuit variant. Please verify wiring per diagnostic procedures, as well as removal & installation guidance called out in the service manual before replacement.
0823023
Radio Over The Air Updating From QR39.6 to QR40.12 Software Version Customers may experience one or more of the following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.
S238A000048
Radio Reset After Clock Adjustment
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
93486
Warranty Bulletin D-23-19 Drop Top Customs Modifications - 2022 and 2023 Dodge Challenger Convertible Component/ LOP Restrictions
93579
FCA Caribbean Warranty Bulletin ID-23-22 Drop Top Customs Modifications - 2022 and 2023 Dodge Challenger Convertible Component/ LOP Restrictions
S2323000075
2nd Row Center Seat Lazy Or Slow When Folding.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
S2221000003
8-Speed Transmission, Additional Transmission Fluid Leak Inspection/Repair Guidelines.
S2307000002
Suspected engine coolant leak.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
1809523
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0455 - EVAP System Large Leak. ? P0456 - EVAP System Small Leak. ? P0440 - General Evap System Failure. ? P0441 - EVAP Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.
1809623
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0455 - EVAP System Large Leak. ? P0456 - EVAP System Small Leak. ? P0440 - General Evap System Failure. ? P0441 - EVAP Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.
2400623
A/C Diagnostic LOP Change
1809023
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0455 - EVAP System Large Leak. ? P0456 - EVAP System Small Leak. ? P0440 - General EVAP System Failure. ? P0441 - EVAP Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.
1809123
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0455 - EVAP System Large Leak. ? P0456 - EVAP System Small Leak. ? P0440 - General EVAP System Failure. ? P0441 - EVAP Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.
S2108000093
Apple CarPlay Does Not Work Or Not Connecting
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0818123
Radio Over The Air Updating to QR40.12 Software Version ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023
9100187
Brake Vacuum Pump For DTC Code P258B - ELECTRONIC VACUUM PUMP PERFORMANCE. Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.
S238A000034
USB Hub In-Operable
S238A000028
Radio Black Screen, Freezing, Reset, Cutting Out Or Inoperative Intermittently
S2208000152
Alarm Intermittently Goes Off While Parked, False Alarm Complaints
9100160
Power wndow switch passenger
0300223
Clicking or Grinding Noise When Accelerating A clicking or grinding noise when accelerating. This bulletin involves replacing the rear driveshaft (propeller shaft).
0700723
Water Quality When Mixed With Engine Coolant
S238A000024
SOS, Assistance Calls Not Successful After Radio Replacement or Radio Software Update
2305123
345 Fender Badges Missing Both 345 fender badges (Fig. 1) are missing. This bulletin involves installing both 345 fender badges.
S238A000021
Radio Display Screen Blank Or Screen Cuts In And Out
9100142
Mirror
0810223
Amplifier (AMP) Software Update
1400323
Diesel Exhaust Fluid (DEF) Fluid Freezing Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software.
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9100146
CAMERA, Rear View Please consult STAR Online S2208000045 prior to replacing the camera. Cameras must be inoperative or fail the blurry image test to be eligible for warranty. All parts must be returned for analysis. If parts are found to be working as designed and trouble not found, a chargeback may be applied. Prior to camera replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Newsletter
FCA CARIBBEAN WARRANTY OPERATIONS NEWSLETTER
0806423
Radio Over The Air Updating to QR40.12 Software Version Mobile Wi-Fi inoperative upon start up. ? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S228A000028
Radio Remained On After Ignition Is Switched Off, Dead Battery From Excessive Radio Current Draw
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
08-022-23
Radio Over The Air Updating to 40.12 Software Version Mobile Wi-Fi inoperative upon start up. Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.
9004541
GEAR Rack And Pinion If gear PN on vehicle is 68526090AA and is one of the following configurations, the replacement gear PN will be 68526096AB. All other applications use 68526090AB. Challenger 3.6L SDE/SDD: 5ZS + (SDE or SDD) + ERB + TR9 Challenger 5.7L SDD/SDE: 5ZS + (SDE or SDD) + (EZC or EZH) + TVH or TT1 Challenger 5.7L SDD/SDE: 5ZS + (SDD or SDE) + (EZC or EZH) + TR9 300/Charger LHD RWD 3.6L SDE: 5AD + SDE + ERB + 5I8 + (TVH or TT1) OR 5ZR + SDE + ERB + 5I8 + TVH or TT1 Charger LHD RWD 3.6L SDE: 5AD + SDE + ERB + 5I8 + TR9 Charger LHD RWD 5.7L SDE: 5AD + SDE + EZH + 5I8 + TR9
08-008-23
UAS and UCS Radio Enhancements Customers may experience one or more of the following: **Wi-Fi hotspot connection failure. Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Wireless connectivity pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXMT icon inoperative. SXMT favorite song not displaying/playing. High pitch squeal, pop or hum noise from speakers. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Performance control home screen shows ?Norm? mode for engine/transmission even when the vehicle is in ?Drag? mode (LA, LD, LX only). Can not change the time on the clock (LA, LD and LX only). USB hub inoperable (D-Trucks only). Backup camera gridlines missing (D-Trucks only). Device not supported message (D-Trucks only). Remote app inoperative (D-Trucks only). Unable to adjust volume (D-Trucks only). Heated steering wheel inoperable (D-Trucks only). In addition, the following enhancement are included in this update: CarplayT connectivity improvements. Improvement to wireless connectivity phone pairing. Improved sound quality when using a wireless connectivity phone. **This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**
S2323000002
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
08-003-22 REV. A
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
Z83 Combo Rev1
Customer Satisfaction Notification Z83 Performance Feature Guide
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2208000152 Rev.
Alarm Intermittently Goes Off While Parked, False Alarm Complaints
08-219-22
Flash: Security Gateway Module (SGW) Updates This bulletin involves reprogramming the SGW with the latest available software to enable High Octane functionality for vehiclesthat have installed the Direct Connection Stage Kits. For customers that have the Direct Connection Redeye Stage I and Stage II kits installed on their vehicle, this flash is requiredto enable functionality of the High Octane Mode.
9100103
Engine Oil - 0W20,Fluid - ATF+4,Engine Oil - 10W30,Engine Oil - 5W20,Engine Oil - 5W30
9100104
SENSOR Intrusion Module
9100105
Seal, Sunroof
9100008
Telematic box module 2
2304822
Door Trim Panel Bolster Delamination
9100096
Base Headlamp Bright, Base Headlamp Black
0500522
Vibration When Braking
Z83
Performance Feature Guide
S2208000152RevA
Alarm Intermittently Goes Off While Parked, False Alarm Complaints
S2208000138RevA
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100088
RADIO ASSY - AUDIO ENTERTAINMENT With the concern of performance page app not loading, or not working, please diagnose the issue per STAR Online S228A000032 before ordering a radio. You can contact FCA Redacted Content for further assistance.
Recall Notificat
Customer Satisfaction Notification Z74 Rear Axle
S2223000063
Ambient Temperature Sensor Servicing.
S2223000062
Window Smart Glass Feature Does Not Lower Or Raise Properly When Operating Door Handles
9100042
REAR AXLE ASSY,AXLE RR - DRIVE SHAFT ASSY If customer concern is related to a clunk noise coming from the rear axle when slowing down, perform SOL S2221000002 before replacing parts.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
2303322
Windshield Washer Nozzle Spray Not Uniform This bulletin involves inspecting and if necessary, replacing one or both windshieldnozzles. The customer may describe the following: Windshield washer nozzles do not have sufficient coverage between two nozzles.
S2221000002
8HP70 Automatic Transmissions Clunk Or Knock Type Noise From The Driveline.
S2208000138
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
S2223000049
Water Drips Onto The Accessory Drive Belt and Freezes. Drive Belt May Come Off Pulleys Due To Ice
S228A000012
Speaker Making Crackling or Popping Noise In Navigation or Voice Recognition Mode
S2208000126
RFH Security Flash Update Not Available On Manual Transmission Challengers
83674
CONTROL - HVAC CONTROL
9004542
Rain Sensor Before replacing the rain sensor during a front windshield replacement, contact: FCA Redacted Content If no response in 15 minutes, proceed with repair. If there is no visible damage to the original rain sensor it should be transfered to the new windshield using a new gel pad rather than replacing it.
9004538
HANDLE, Front/Rear Door Exterior Outside release handle loose/coming apart from door If customer comes in with the issue described above, please contact the following individuals prior to servicing the vehicle. FCA Redacted Content If no response in 15 minutes, proceed with repair.
9004531
RECEIVER, Hub The final drop shipment of CSN Z23, P/N 68379519AL, has taken place. No further parts distribution will be taking place. All distributed parts would cover all sold and unsold needs. Please use all stock that your dealer has before asking for parts assistance. If part assistance is still required, please provide the following information to your Area Manager for review: 1. Dealer Code 2. Last eight digits of VIN 3. Appointment date/vehicle VOR at dealer Thank you, Mopar
82975
LATCH - FRONT DOOR
83020
DAMPER - STEERING
83052
RECEIVER - HUB
82973
LAMP - TAIL
0808622
Radio Frequency Hub Module (RFHM) Updates.
82837
DAMPER - STEERING
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
0500122
Front Click Noise at Low Speed Turns This bulletin involves installing a friction disc kit on both front hub bearing surfaces between the hub and rotor. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.
9004493
RAIL, Fuel Prior to replacing this compoenent, please contact one of the following prior to disassembly: FCA Redacted Content If no response in 15 minutes, proceed with repair.
9004475
SEAT BELT, Front (Right) For concern of front passenger seat belt is slow to retract upon exiting the vehicle, check if seat belt webbing is pinched at trim outlet. Seat belt retractor turning loop installation can be adjusted to help give clearance between webbing and trim.
9004440 Rev. A
LATCH, Front Door If the vehicle condition is related to the door window smart glass operation or window not lowering when the outside door handle is actuated latch replacement may be unneccessary. please contact the following individual prior to servicing the vehicle FCA Redacted Content There is a simple door handle to latch adjustment specified in the latch installation service procedure. 23 - Body / Doors - Front / LATCH, Door / Installation. The handle/latch/window switch adjustment is specified in steps 7 through 9.
9004444
SPRING, Valve For conern of misfire or misfire related DTCs and diagnosis leads to a broken valve spring, please replace all valve springs and contact FCA Redacted Content to FasTrak all replaced parts to QEC for further analysis. If no response in 15 minutes, proceed with repair.
9004440
LATCH, Front Door If the vehicle condition is related to the door window smart glass operation or window not lowering when the outside door handle is actuated latch replacement may be uneccessary. There is a simple door handle to latch adjustment specified in the latch installation service procedure. 23 - Body / Doors - Front / LATCH, Door / Installation. The handle/latch/window switch adjustment is specified in steps 7 through 9.
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.