Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
108463
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
108464
PAD KIT - REAR DISC BRAKE, FRONT DISC BRAKE
103239
AIR BAG - SIDE CURTAIN
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0815223
Fuel Pump Connector Replacement The technician may experience a crank/no start after the fuel pump module was replaced. This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004557
Overhead Console If the sunglasses holder door in the overhead console will not stay closed, inspect the Latch for damage. The Latch is now released for service under part number 68599540A$.
S2208000131
No Start Condition After A Fuel Pump Replacement, Multiple Fuel System Level Related DTC?s Setting
9004543
wiring harness Before replacing this harness, please check for an available connector repair kit at the following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
2101214
Transmission Shift Enhancements - Adaptation Drive Learn Procedure
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S1709000010
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010 RevB
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S1709000010RevB
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
0805517
This bulletin involves performing a USB service flash of the Hands Free Module.
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
9004361
NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission
S1709000010 Rev.
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
18-073-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information
1807320
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
UB4 Rev. 6
Emissions Recall UB4 Evaporative Emissions Canister
S1508000480
Speed Control Operates Intermittently
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
08-083-19
Flash: Hands Free Module (HFM) Software Enhancements This bulletin involves reprogramming the HFM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9004036
ACTUATOR, A/C and Heater Before replacing HVAC actuator, please contact either Thomas Conway (248) 635-7090 or Paul Aquino (248) 854-4819. Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.
9004076
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
02-008-17
Servicing Lower Control Arm Inner Pivot Bushings This bulletin discusses replacement of the lower control arm inner pivot bushings.
9003797
5.7L Cold End Exhaust RH Side (Resonator & Muffler) Engineering is currently investigating an issue where the back-end exhaust system (resonator and muffler right hand assembly) cracks at or around the weld near the muffler with Model Year '13, '14, '16, and '17 Charger and Challenger 5.7L. Please call Design Release Engineer Jeff Robinson at cell phone (315) 408-6055 and send a photo of the part to him at Jeff.Robinson@fcagroup.com. If no response in 15 minutes, please proceed with repair.
08-055-17 REV. A
Flash: Hands Free Module Software Enhancements This bulletin involves reprogramming the Hands Free Module (HFM) with the latest available software. The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone®4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth® Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPod®touch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter
0805617
This bulletin involves performing a USB service flash of the Hands Free Module.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
18-088-16B
Powertrain diagnostic and system enhancement.
1808816
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. (Sales Code ERB). (LD, LX vehicles only). P0606 - Internal Control Processor.
1808816B
Powertrain diagnostic and system enhancement.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68140568A$
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other componenets to be replaced). For more information and details on PN's, see L-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
18-088-16
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance. · P0456 - EVAP System Small Leak (Sales Code ERB).** · U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). · P0606 - Internal Control Processor.
18-088-16 REV. A
Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance. · P0456 - EVAP System Small Leak (Sales Code ERB).** · U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). · P0606 - Internal Control Processor.
Parts-3
Steering Column.
18-084-16
Flash: 5.7L Diagnostic And System Improvements This bulletin involves reprogramming of the Powertrain Control Module (PCM) with the latest software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · **P0456 - Evap System Small Leak. · P2610 - PCM Internal Engine Off Timer Performance. · P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. · P0335 - Crankshaft Position Sensor Circuit. (2014-2015 MY).** · U0140 - Lost Communication With Body Control Module. (LC, LD and LX). · P1621 - O2 Sensor Reference Voltage Circuit Low. · P1622 - O2 Sensor Reference Voltage Circuit High. · P0606 - Internal Control Processor. · P0300 - Multiple Cylinder Misfire. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P219B - Bank 2 Air-Fuel Ratio Imbalance. · P0307 - Cylinder 7 Misfire. · P2096 - Downstream Fuel Trim System 1 Lean. · P2097 - Downstream Fuel Trim System 1 Rich.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
R8149638A
Verify two (2) 6102212AA alignment dowel pins are installed in the 4x4 adaptor prior to transmission installation.
R8149638A$
Verify two (2) 6102212AA alignment dowel pins are installed in the 4x4 adaptor prior to transmission installation.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
04584559A$
Steering Gears, Pumps and Hoses This tech tip applies to vehicles built before 12-23-2010, these vehicles can exhibit a squeak or rubbing noise when turning the steering wheel. Do not replace the steering gear, steering pump, power steering pressure hose or power steering return hose before investigating the dash seal ring. The source of the noise may be the sealing ring under the dash seal. To correct the issue apply MOPAR product part number 04318070AD (Silicone Spray Lube) to the inner dash seal interface and also the outer engine compartment interface. Do not use any alternate lubricants. If MOPAR product part number 04318070AD (Silicone Spray Lube) is not available then replace the assembly. Refer to TSB 08-091-14.
18-074-15 REV A
Flash: 6.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0122 - Throttle Position Sensor 1 Circuit Low. ? P0123 - Throttle Position Sensor 1 Circuit High. ? P0222 - Throttle Position Sensor 2 Circuit Low. ? P0223 - Throttle Position Sensor 2 Circuit High. ? U0140 - Lost Communication With Body Control Module (Attempting to clear this DTC will be unsuccessful).
1807415REVA
Powertrain Diagnostic And System Enhancements.
10-002-15
Seat Belt Interaction With Police Equipment
18-086-15 REV A
Flash: Powertrain System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM) (VF, LD, LX Vehicles only). ? P0606 - Internal Control Processor.
18-089-15
Flash: Diagnostic And System Improvements/Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more one of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? P0456 - Evap System Small Leak.
08-114-15 REV A
Radio Software Enhancements This bulletin involves updating the radio's software. CAUTION: Confirm the correct radio flash file to the applicable model and family vehicle before flashing. A customer may experience one or more of the following: ? Radio display screen intermittently may go blank. ? Radio display screen may lock up. ? Back up display may not turn off. ? Loss of radio memory for skipped channels or incorrectly displaying skipped channels in the menu list. ? Charging schedule showing in the setting menu (FF BEV only). ? Korean language was not supported (APAC - Korea only). Enhancement: ? Removing the charging schedule from showing in the setting menu (FF BEV only). ? Adding Korean language support (APAC - Korea only).
18-086-15
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1808615
Powertrain System Improvements/Enhancements.
08-033-15 REV B
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank (Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only) (Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone aft
0803315REVB
This bulletin involves updating the radio control head software and navigation if equipped.
18-074-15
Flash: 6.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module with the latest available software. The technician may find the following Diagnostic Trouble Code (DTC) set in the Powertrain Control Module (PCM) memory: ? U0140 - Lost Communication With Body Control Module NOTE: Attempting to clear this DTC will be unsuccessful.
21-049-15
Flash: Transmission Shift Enhancements This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ) and are broken down per engine application. 3.6L Engine (LD/LX) ? Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures. ? Poor performance when driving aggressively. ? Hanging in gear during HOT ambient temperature conditions and high engine loads. ? Excessive pedal needed to downshift in high altitudes (i.e. passing). ? Poor shift quality, or high transmission temperatures during track or sport driving. 3.6L Engine (LD Police) ? Erratic shifting or poor performance complaints while driving up steep hills, or at high altitude during hot ambient temperatures. ? Poor performance when driving aggressively. 5.7L Engine (LD/LX) ? Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures. ? Poor shift quality (bump or torque disturbance) when coasting to a stop. ? Poor city fuel economy (AWD Only). ? Hanging in gear at high engine speeds during aggressive driving. ? Gear shift point enhancements during high load or race track driving. ? Excessive pedal needed to downshift in high altitudes (i.e. passing). ? Poor shift quality or high transmission temperatures during track or sport driving. ? Improved acceleration response from speeds greater than 36 Mph (58 Kph) (Japan Market Only). ? Bump sensation felt during deceleration or braking. 5.7L Engine (LD Daytona) ? Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures.
SB-21-049-15
2013 DODGE CHARGER AND 2013 CRYSLER 300: REPROGRAMMING AND SELECTIVELY ERASING FOR TRANSMISSION CONTROL MODULE WITH IMPROVED NEW SOFTWARE THAT IS AVAILABLE FOR VEHICLES EQUIPPED WITH WA580 AUTOMATIC TRANSMISSION. *CN
08-033-15 REV-A
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank(Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only)(Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after
SB-08-033-15REVA
CERTAIN VEHICLES ARE EXPERIENCING SCREEN LOCK UP ON NAVIGATION OR DISPLAY BLANK, RADIO WILL RESET, INTERMITTENTLY, NOT ABLE TO DIAL PHONE FROM RADIO BUT CAN DIAL PHONE, TRANSLATION FOR ASIAN LANGUAGE ADDED, AFTER DISCONNECTION PHONE, FAILS TO CONNECT PHONE, ETC. MODEL 2013-14 CHARGER, CHRYSLER 300, JOURNEY. *PE
18-052-15
CHRYSLER 2013-2014 DODGE CHALLENGER, DODGE CHARGER, CHRYSLER 300: REGARDING REPROGRAMMING THE POWERTRAIN CONTROL MODULE WITH THE LATEST AVAILABLE SOFTWARE. *LJ
23-018-15
Rattle Or Buzzing Noise In Rear Shelf Area With Radio On Or While Driving On Bumpy Roads This bulletin involves modification or replacement of the backlite rear shelf. The customer may describe a rattle or buzz noise coming from the rear of the vehicle with the radio on or while driving on bumpy roads. This may be caused by the rear shelf moving relative to the backlite.
2301815
This bulletin involves modification or replacement of the backlite rear shelf
07-002-15 REV. A
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
08-033-15
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Improve AM/FM radio reception. (This only applies to 2013 or 2014 vehicles with RE6, RB6 radios located in Dubai). ? Intermittently the radio may reset. ? Radio display screen shows ?Test Mode?. ? Navigation screen locks up or display will be blank. ? Navigation feature lockout disable (International Only). ? Navigation system resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after it has been disconnect. ? Teleprompter screen shows incomplete text. ? Some functionality for traffic & weather jump button. ? After ch
08-020-15
Flash: Blind Spot Monitor System Improvements This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. The customer may experience the blind spot monitor indicator in either outside mirror maybe flashing or on continuously. On further inspection the technician will Not find any DTCs. Symptom/Condition for RT vehicles ONLY: Customer may experience that the indicator in the side view mirrors may not illuminate when there is an object on either side of the vehicle.
CHRYSLER
The customer may experience the blind spot monitor indicator in either outside mirror maybe flashing or on continuously.
SB-08-020-15
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9002887
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
07-002-15
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
09-002-14 REV. B
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
0900214REVB
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
0900214a
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
21-041-14
845RE Harsh 2-1 Downshift This bulletin involves replacing the transmission valve body. A small number of customers may experience a bump sensation during a 2-1 downshift. This condition can occur at any transmission temperature and is most noticeable during light braking or while coasting to a stop. No Diagnostic Trouble Codes (DTCs) will be set as a result of this.
2104114
Convergence Telematics Module (CTM) Software Enhancements This bulletin involves updating the Convergence Telematics Module (CTM) software. The customer may notice the steering wheel controls and USB functionality may not operate properly after the ignition is cycled.
02-007-14
Front End Clunk Noise When Coming To A Stop - Police Vehicles Only This bulletin involves replacing the left side or the right side or both side tension struts. Police vehicles with heavy duty suspension and rear wheel drive may experience a front end clunk noise, coming from the tension strut bushing(s), while coming to a stop.
0200714
This bulletin involves replacing the left side or the right side or both side tension struts.
09-002-14 REV. A
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
0900214
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension)
21-012-14 REV. B
8 Speed Transmission Shift Adaptation, Drive Learn Procedure This bulletin involves performing a Transmission Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
08-040-14 REV. A
Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
08-040-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0804014
Police Vehicle A/C Inoperative This bulletin involves relocating the A/C fuse within the front Power Distribution Center (PDC). Customer comments A/C is warm. On further inspection the technician will notice the A/C clutch fuse is loose in its cavity (#12) in the PDC. This will cause a poor connection and the fuse cavity to be distorted.
21-028-14
Flash: Transmission Shift Enhancements This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ) and are broken down per engine application.3.6L Engine Hanging in gear during HOT ambient temperature conditions and high engine loads. Excessive pedal needed to downshift in high altitudes (i.e. passing). Poor shift quality, or high transmission temperatures during track or sport driving.5.7L Engine Hanging in gear at high engine speeds during aggressive driving. Gear shift point enhancements during high load or race track driving. Excessive pedal needed to downshift in high altitudes (i.e. passing). Poor shift quality or high transmission temperatures during track or sport driving. Improved acceleration response from speeds greater than 36 Mph (58 Kph) (Japan Market Only). Bump sensation felt during deceleration or braking.6.4L Engine Bump sensation felt during deceleration or braking. Inconsistent downshift during Wide Open Throttle (WOT) accelerations at highway speeds (i.e. passing). Transmission enhancements to improve acceleration while in reverse going uphill on steep grades.3.0L Engine (LX Only) Erratic excessive shifting during low speed, light pedal driving.
2102814
Flash: Transmission Shift Enhancements This bulletin involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ) and are broken down per engine application.3.6L Engine Hanging in gear during HOT ambient temperature conditions and high engine loads. Excessive pedal needed to downshift in high altitudes (i.e. passing). Poor shift quality, or high transmission temperatures during track or sport driving.5.7L Engine Hanging in gear at high engine speeds during aggressive driving. Gear shift point enhancements during high load or race track driving. Excessive pedal needed to downshift in high altitudes (i.e. passing). Poor shift quality or high transmission temperatures during track or sport driving. Improved acceleration response from speeds greater than 36 Mph (58 Kph) (Japan Market Only). Bump sensation felt during deceleration or braking.6.4L Engine Bump sensation felt during deceleration or braking. Inconsistent downshift during Wide Open Throttle (WOT) accelerations at highway speeds (i.e. passing). Transmission enhancements to improve acceleration while in reverse going uphill on steep grades.3.0L Engine (LX Only) Erratic excessive shifting during low speed, light pedal driving.
08-037-14 REV. A
Flash: RB4 Radio Enhancements This bulletin involves updating the radio and navigation software, if required. A customer may experience, one or more of the following conditions: Radio display screen shows ?Test Mode?. Navigation screen locks up or display will be blank. Navigation feature lockout disable (International Only). Navigation system resets intermittently. Translation improvements/corrections. System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. Radio system improvements during remote start operation. Unable to adjust radio volume using steering wheel switch intermittently. Second screen is blank when using split screen function. The symbol of the car on the map will move erratic, Jerks, Jumps or Backwards. The indication of the highlighted path may be missing at times. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. Blackberry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. iPod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more than one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. When in Italian, the destination arrives.
08-037-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-030-14 REV. A
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio?s software and Navigation if required. A customer may experience, one or more of the following conditions: Radio display screen shows ?Test Mode?. Navigation screen locks up or display will be blank. Navigation feature lockout disable (International Only). Navigation system resets intermittently. Translation improvements/corrections. System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. Radio system improvements during remote start operation. Unable to adjust radio volume using steering wheel switch intermittently. Second screen is blank when using split screen function. Some functionality for Japanese and Korean - keyboard, search, sort and jump. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. BlackBerry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. Viod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more then one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. When in Italian, the destination arrival text will overlap onto the
08-030-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-034-14 REV. A
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
21-012-14 REV. A
Transmission Shift Enhancements - Adaptation Drive Learn Procedure This bulletin involves performing a subjective shift quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
21-012-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9003103
Part Description: Fuel Pump Module Issue Description: This TechTip applies to ONLY Charger (LD) 2011 thru 2014MY vehicles equipped with sales code AHB- Police Group. For vehicles operating under excessive idling condition an alternative high performance pump is available if the customer prefers. Part number 68103913AB or 68145815AA when used with XDC- Fuel Tank
09-002-14
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire
18-034-14
P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
SB-18-034-14
ON SOME MODEL VEHICLES AND JEEPS, (MY 2013-2014)MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES AND DIAGNOSTIC TROUBLE CODE (DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
21-012-14
Transmission Shift Enhancements - Adaptation Drive Learn Procedure This bulletin involves performing a subjective shift quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.
08-037-14
RB4 Radio Enhancements This bulletin involves updating the radio and navigation software, if required. A customer may experience, one or more of the following conditions: The symbol of the car on the map will move erratic, Jerks, Jumps or Backwards. The indication of the highlighted path may be missing at times. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. BlackBerry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. iPod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more than one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. When in Italian, the destination arrival text will overlap onto the map. Does not accept Iraq when commanding ?Set Target Country?. Some pop up message characters is displayed with ?!#?. Traffic programming slow to start.
08-030-14
RB5 RE2 RB6 RE3 RE6 RE4 RE7 RE9 Radio Enhancements This bulletin involves updating the radio?s software and Navigation if required. A customer may experience, one or more of the following conditions: Add China phone book search. Some functionality for China, Japanese and Korean - keyboard, search, sort and jump. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. BlackBerry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. iPod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more then one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. When in Italian, the destination arrival text will overlap onto the map. Does not accept Iraq when commanding ?Set Target Country?. Some pop up message characters is displayed with ?!#?. Traffic programming slow to start.
08-011-14
Flash: Hands Free Module Defaults To English Instead Of Last Language Selected This Bulletin involves performing a USB service flash of the Hands Free Module (HFM). The customer may note when trying to select a none supported language like Russian or Portuguese the Hands Free screen will default to English. The Voice Recognition (VR) will default back to the last language (Italian, French, Spanish, German or Dutch) the customer was using. After the software updated has been completed both the Hands Free screen and VR will default back to the last language used. VR Teleprompter enhancement.
08-084-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-087-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-084-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-081-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-038-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-046-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-062-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-043-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-047--13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-047-13
Flash: Inaccurate Outside Temperature Display This bulletin involves updating the Body Control Module (BCM) software. Customer may experience a delay to update the ambient air temperature display with the actual ambient air temperature. This condition is more noticeable during short/slow commutes and with a large ambient air temperature increase between drive cycles.
0804713
Flash: Inaccurate Outside Temperature Display This bulletin involves updating the Body Control Module (BCM) software. Customer may experience a delay to update the ambient air temperature display with the actual ambient air temperature. This condition is more noticeable during short/slow commutes and with a large ambient air temperature increase between drive cycles.
08-043-13
Flash: SRT Auto Transmission, Adding Launch Control Feature This bulletin involves updating the Anit-lock Brake System (ABS) module, Cluster and Totally Integrated Power Module (TIPM), if required. The customer may note that the launch control feature is missing.
0804313
Flash: SRT Auto Transmission, Adding Launch Control Feature This bulletin involves updating the Anit-lock Brake System (ABS) module, Cluster and Totally Integrated Power Module (TIPM), if required. The customer may note that the launch control feature is missing.
08-038-13
Radio RB5 RE2 RE6 RB6 RE3 RB4 RE4 RE9 RE7 Headlamp Delay Off Option Missing From Menu This Bulletin involves updating the radio's software. A customer may note that the Headlamp delay off option is missing from the customer settings menu.
08-033-13
Flash: Two Or More Speakers Will Mute When Playing Certain Media Sources This bulletin involves reprogramming the Amplifier with updated software. The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.
08-032-13
Flash: No Audio From The Radio Caused By The Amplifier Not Communicating This bulletin involves re-flashing the Amplifier with updated software. The customer may indicate that there is no audio and/or radio is muted. This condition may be caused by the amplifier not communicating on the bus.Flashing the amplifier will correct this condition.
9002900
Part Description: Switch-Padedle Down Audio LT. Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.
08-013-13 REV. A
This bulletin involves reconfiguring the vheicle display the passive entry Enable/Disable feature on the menu screen.
08-013-13EV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
23-016-13
This bulletin involves replacing the power seat track drive block bolts on front driver and/or passenger seat. The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
9002838
04627731A$ - Trans Vent Hose The upper end of the transmission vent hose terminates with an open elbow. There is no cap on the end of the vent hose. This is intentional. Some graphics in StarParts may show a vent hose including a cap, but this is incorrect. The actual production vent hose has an open elbow fitting, not a cap. The elbow should be pointing downwards in the vehicle.~
08-016-13
Flash: Indicator For The Blind Spot Monitor Is Flashing Or On Continuously This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. Not find any DTC's.
23-011-13 REV. A
Passenger Compartment Odor This bulletin involves replacing all door weatherstrip seals and decklid seals on select models. The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.
23-011-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-007-13 REV. A
MIL Illumination P0300 and/or Engine Runs Rough With Factory Fill Fuel This bulletin involves filling the fuel tank with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).
18-007-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-013-13
Passive Entry Enable/Disable Feature Is Missing In Customer Setting Menu This Bulletin involves reconfiguring the vehicle to display the passive entry Enable/Disable feature on the menu screen. The customer may note when trying to disable the passive entry feature this option is missing in customer settings
05-003-13
Front And/Or Rear Brake Noise (Squeal) This bulletin involves changing front and rear brake pads to correct a brake squeal noise. The customer may experience a squealing noise during braking coming from the front and/or rear of the vehicle.
23-011-13
Passenger Compartment Odor This bulletin involves replacing all door weatherstrip seals and decklid seals on select models. The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.
18-007-13
MIL Illumination P0300 and/or Engine Runs Rough With Factory Fill Fuel This bulletin involves filling the fuel tank with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. NOTE: A Service Porter will be able to complete all necessary repair procedure steps with the exception of Step 7. Only in situations where Step 7 is necessary, should vehicle be dispatched to a Service Technician to clear DTCs. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).
09-001-13
Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
07-004-12 REV. A
Attention! Release Of New Engine Coolant Organic Additive Technology (OAT) Chrysler Corporation LLC. has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.