Vehicle report

2014 DODGE DART

Compare every DODGE DART yearNHTSA and EPA records

Service bulletins

187 bulletins

Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.

31-001-25 REV. B

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

9100645

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

9100653

Service Bulletin/Repair Instructions

Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

31-001-25 REV. A

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

31-001-25

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

U90 - Parts Ordering

Other

U90 - Parts Ordering

09-018-24

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

100096

Other

U90 Parts Ordering

31-001-24

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

S1408000384

Service Bulletin/Repair Instructions

Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

9100229

Service Bulletin/Repair Instructions

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

S2325000007

Service Bulletin/Repair Instructions

MIL/check engine lamp comes on after performing U90 recall PCM software update.

9100226

Service Bulletin/Repair Instructions

Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

RecallU90

Service Bulletin/Repair Instructions

Emissions Recall U90 - Catalyst Efficiency

93023

Service Bulletin/Repair Instructions

Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)

93120

Service Bulletin/Repair Instructions

FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC

9100196

Service Bulletin/Repair Instructions

Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used

0700723

Service Bulletin/Repair Instructions

Water Quality When Mixed With Engine Coolant

1804823

Service Bulletin/Repair Instructions

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

0900323

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

3100123

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

09-003-23

Service Bulletin/Repair Instructions

2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: Oil pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

88806

Service Bulletin/Repair Instructions

Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

31-002-22

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

09-013-22

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

3100122

Service Bulletin/Repair Instructions

Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

9003354

Service Bulletin/Repair Instructions

Fiat C-635 Dual Dry Clutch (DDCT) Automatic Transmission Fluid Fill The Fiat C-635 DDCT and C-633 DDCT are shipped without fluid. Fill per DealerConnect procedure: "draining, filling and level check"

S2209000004

Service Bulletin/Repair Instructions

If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.

9004509

Service Bulletin/Repair Instructions

Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

CSNW20

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

W20

Service Bulletin/Repair Instructions

Powertrain Control Module.

S2109000004

Service Bulletin/Repair Instructions

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

9004386

Service Bulletin/Repair Instructions

WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

W20 Combo Phase4

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

S2008000113

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S2008000113 Rev.

Service Bulletin/Repair Instructions

No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message

S1821000001

Service Bulletin/Repair Instructions

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

9004009

Service Bulletin/Repair Instructions

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

S1809000007 Rev.

Service Bulletin/Repair Instructions

Customer complaint may include engine oil leak/consumption.

S1408000259 Rev.

Service Bulletin/Repair Instructions

Radio Display Screen Goes Blank During ABS Activation, HVAC Controls And Blind Spot System Operate Intermittently, Cluster Warning Chime Goes Off

S1408000259RevA

Service Bulletin/Repair Instructions

Radio Display Screen Goes Blank During ABS Activation, HVAC Controls And Blind Spot System Operate Intermittently, Cluster Warning Chime Goes Off

W20 Combo Phase3

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)

S2108000027

Service Bulletin/Repair Instructions

CEL, Check Engine Lamp On, DTC P0339 Crankshaft Position Sensor Intermittent

W20 Combo Phase2

Service Bulletin/Repair Instructions

Customer Satisfaction Notification W20 Reprogram Powertrain Control Module

31-002-20

Service Bulletin/Repair Instructions

Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

3100220

Service Bulletin/Repair Instructions

09-006-20 REV. B

Service Bulletin/Repair Instructions

2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

0900620

Service Bulletin/Repair Instructions

S2008000093

Service Bulletin/Repair Instructions

Blind Spot Or Park Assist Warnings, False Activation

09-006-20 REV. A

Service Bulletin/Repair Instructions

09-006-20

Service Bulletin/Repair Instructions

23-015-20

Service Bulletin/Repair Instructions

Disinfectant Solution Recommended for COVID-19

08-049-20

Service Bulletin/Repair Instructions

Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

18-039-20

Service Bulletin/Repair Instructions

Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season

S2019000002

Service Bulletin/Repair Instructions

Hands On Steering Wheel Message In EVIC

S1508000480

Service Bulletin/Repair Instructions

Speed Control Operates Intermittently

9004022

Service Bulletin/Repair Instructions

Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

31-003-19

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

31-004-19

Service Bulletin/Repair Instructions

Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.

31-005-19

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

31-006-19

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

3100319

Service Bulletin/Repair Instructions

Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.

3100419

Service Bulletin/Repair Instructions

3100519

Service Bulletin/Repair Instructions

Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.

3100619

Service Bulletin/Repair Instructions

Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.

9003220

Service Bulletin/Repair Instructions

RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

9003355

Service Bulletin/Repair Instructions

3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

9003579

Service Bulletin/Repair Instructions

Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY: Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module: DTC: B223D-00 - OCM DTC Present DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair. FCA Engineering Contacts: Jay Nagle (ORC Module, Driver/passenger seat track position sensor, OCM for PF, KL or UF Vehicles ONLY) @ cell (248) 576-5657

9003676

Service Bulletin/Repair Instructions

Reverse Lockout Cable If vehicle comes in for a broken reverse lockout cable, you can now order the cable by itself as PN 68376046AA. If vehicle is has the silver OE shift knob, you will also need to order a new upper (68157603A*) and lower (68087185A*) shifter knob pieces. You can find instructions for replacing the cable under LOP 21-75-31-01.

9003357

Service Bulletin/Repair Instructions

Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

9003109

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

18-022-17 REV. A

Service Bulletin/Repair Instructions

Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs set in the PCM memory: U1504 - Implausible Message Data Length Received From Steering Angle Sensor. P0128 - Thermostat Rationality. P0335 - Crankshaft Position Sensor Circuit. P0340 - Camshaft Position Sensor Circuit Bank 1 Sensor 1. U1424-00 - Implausible Engine Torque Signal Received. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance.In addition to the DTCs above the following improvements have been made: Min spark changes to prevent catalytic converter overheating. Engine Startup Flare and Idle Surge. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. U0401 - Implausible Data Received From ECM/PCM - Signal Invalid.

9003694

Service Bulletin/Repair Instructions

Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

9003687

Service Bulletin/Repair Instructions

Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

9003681

Service Bulletin/Repair Instructions

Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

68234120

Service Bulletin/Repair Instructions

Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A for an exchange or 05064993A for a new part replacement. Prior to replacing parts, Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~ ~______________________________________~ Contact Us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. DO NOT email regarding repair procedures unrelated to this Tech Tip or part order inquires. Please include the Part Number (s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

05152029

Service Bulletin/Repair Instructions

Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

06-001-16 REV. A

Service Bulletin/Repair Instructions

Clutch Pedal Operation X62 Extended Warranty This bulletin involves the replacement of the hydraulic clutch master cylinder and reservoir hose. Some customers may experience a reduction in clutch pedal stroke.

D-160-1

Service Bulletin/Repair Instructions

(X62) Hydraulic Clutch Master Cylinder / Reservoir Hose - 2013-2015 Dodge Dart and 2014-2015 Jeep Cherokee (Rev. A) To announce an extended warranty on the Hydraulic Clutch Master Cylinder/ Reservoir Hose on the following vehicles: ? 2013-2015 Dodge Dart (PF) ? 2014-2015 Jeep Cherokee (KL)

68264880A

Service Bulletin/Repair Instructions

Parts.

68264880A$

Service Bulletin/Repair Instructions

Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY:~ Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent, corroded, or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Malcolm Whitehouse (OCM Module - PF,KL, or UF Vehicles ONLY)@248-462-4703 or Malcolm.Whitehouse@fcagroup.com.~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com~

18-023-16

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - EVAP System Small Leak. · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module.

18-023-16 REV. D

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition T

05047457A

Service Bulletin/Repair Instructions

Multi-Air Actuator Assembly For 2.4 Tigershark Engine ONLY: When attempting to diagnose P Codes related to the MultiAir Unit, please note that there are multiple causes listed for each in the diagnostic procedure. This procedure must be followed to ensure the correct condition is being addressed. ~ Please verify the following (as listed in the first step in diagnostics) is not present before attempting repair:~ - Low Engine Oil - Incorrect oil filter that does not meet OEM specifications - Oil Dirty or Deteriorated (Lack of scheduled oil changes) - Incorrect Oil Viscosity/Weight - Engine Oil Contaminated (i.e. coolant and/or fuel) - Clogged Oil Galley Screen/Filter (top of block - feeds Multi-Air Unit) If there are any questions please contact: Seth Nankee at cell: (248) 303-5434 seth.nankee@fcagroup.com If no response within 15 minutes, please continue with diagnostics/repair.

68234120A$

Service Bulletin/Repair Instructions

18-023-16 REV. C

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). · Cold Idle Surge With AC Engaged

18-023-16 REV.C

Service Bulletin/Repair Instructions

FLASH: 2.4L POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS. BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION OR ONE OR MORE OF THE FOLLOWING CONDITIONS. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM, MEMORY:2015 UF VEHICLES WITH (SALES CODES ED6, ED8)· P050D - COLD START ROUGH IDLE. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.· P0480 - COOLING FAN 1 CONTROL CIRCUIT/OPEN. U0402 - IMPLAUSIBLE DATA RECEIVED FROM TCM. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE. U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. · P0441 - EVAP PURGE SYSTEM PERFORMANCE. · P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE.IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE:ENGINE STARTUP FLARE AND IDLE SURGE.IMPROVED VEHICLE ACCELERATION. 2015 PF VEHICLES WITH (SALES CODES ED6, ED8)U0401 - IMPLAUSIBLE DATA RECEIVED FROM ECM/PCM - SIGNAL INVALID. P1185 - GENERAL PRESSURE SENSOR CORRELATION.P050D - COLD START ROUGH IDLE. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.P219A - BANK 1 AIR-FUEL RATIO IMBALANCE. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE.U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE. P050B - COLD START IGNITION TIMING PERFORMANCE. P061A - LEVEL 2 TORQUE PERFORMANCE.P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED (INSTANTANEOUS ACCUMULATION).IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE: LOW IDLE SPEED AFTER COLD START BETWEEN -10°C TO 0°C (14°F TO 32°F).

18-067-16

Service Bulletin/Repair Instructions

Flash: 2.0L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may describe a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following DTCs set in the PCM memory: · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance.** · U0140 - Lost Communication With Body Control Module. · P1D73 - AGS Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P0456 - Evap System Small Leak. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · Electronic Vehicle Information Center (EVIC) Fuel Economy display accuracy. · Improved Enhanced Automatic Oil Change Indicator (EAOCI) system accuracy. · Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

18-023-16 REV. B

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation.** P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F). Cold Idle Surge With AC Eng

68105583A

Service Bulletin/Repair Instructions

Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

18-023-16 REV. A

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).

1802316REVA

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) · **P050D - Cold Start Rough Idle. · P0335 - Crankshaft Position Sensor Circuit. · P1607 - PCM Internal Shutdown Timer Rationality. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak.** · P0480 - Cooling Fan 1 Control Circuit/Open. · U0402 - Implausible Data Received From TCM. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0441 - Evap Purge System Performance. · P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: · Engine Startup Flare and Idle Surge. · Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) · P050D - Cold Start Rough Idle. · P0133 - O2 Sensor 1/1 Slow Response. · P0456 - Evap System Small Leak. · P219A - Bank 1 Air-Fuel Ratio Imbalance. · P2172 - High Airflow/Vacuum Leak Detected. · P1D73 - AGS Performance. · U0140 - Lost Communication With Body Control Module. · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050B - Cold Start Ignition Timing Performance. · P061A - Level 2 Torque Performance. · P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: · Low Idle Speed After Cold Start between -10°C to 0°C (14°F to 32°F).

68141352A

Service Bulletin/Repair Instructions

3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

68234120A

Service Bulletin/Repair Instructions

Z5091195A

Service Bulletin/Repair Instructions

RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Z5091195A$

Service Bulletin/Repair Instructions

68277402A

Service Bulletin/Repair Instructions

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

08-028-16

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

0802816

Service Bulletin/Repair Instructions

This bulletin involves updating the radio software and navigation if equipped.

08-023-16

Service Bulletin/Repair Instructions

RB5 RB6 Radio Software Enhancements (X66 Warranty Extension) This bulletin involves updating the radio and navigation software or replacing the radio. SYMPTOM/CONDITION: Customers may experience one or more of the following symptoms/conditions: · Radio screen will lock up and reset intermittently. · Unable to turn on heated seats; screen icon is greyed out. · Navigation screen goes blank. · Navigation system freezes/locks up. · Incorrect routing directions to fuel stations when using Travel Link. · Navigation icon shows the vehicle going backward when it?s moving forward. · Map checksum error may be displayed when attempting to update the navigation system maps.

D-16-05

Service Bulletin/Repair Instructions

(X66) RB5 & RB6 8.4 Nav Radio - 2014-2015 Dodge Dart (PF). To announce an extended warranty on the RB5 & RB6 8.4 Nav Radio on the following vehicles: 2014-2015 Dodge Dart (PF)

68210293A$

Service Bulletin/Repair Instructions

MODULE, Transmission Control This generic TCM must be flashed with the ignition in the accessory position. Attempts to flash with the ignition in the run position may result in flash failures

RL108213A$

Service Bulletin/Repair Instructions

NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

06-001-16

Service Bulletin/Repair Instructions

0600116

Service Bulletin/Repair Instructions

Clutch Pedal Operation X62 Extended Warranty.

D-16-01

Service Bulletin/Repair Instructions

HYDRAULIC CLUTCH MASTER CYLINDER/RESERVOIR HOSE (X62)-2013-2015 DODGE DART AND 2014-2015 JEEP CHEROKEE.

D-16-01 X62

Service Bulletin/Repair Instructions

Warranty.

D1601X62

Service Bulletin/Repair Instructions

Warranty Bulletin

18-006-15 REV H

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8) ? P0133 - O2 Sensor 1/1 Slow Response. ? P0456 - Evap System Small Leak. ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles (Sales Codes ED6)

18-006-15 REV. H

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

18-009-15 REV G

Service Bulletin/Repair Instructions

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump sensation felt during moderate to heavy acceleration over 3,500 RPM. ? P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Cold start difficulty below -10°C (14°F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)). 2014 Dart ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylind

1800615 REV H

Service Bulletin/Repair Instructions

Powertrain Diagnostic and System Improvements.

1800915 REV G

Service Bulletin/Repair Instructions

Drivability Improvements.

1800915REVG

Service Bulletin/Repair Instructions

Drivability Improvements.

06509898A

Service Bulletin/Repair Instructions

Part Description: Nut - Front Hub & Bearing Issue Description: Whenever replacing the front Hub & Bearing Halfshaft Nut, make sure to torque to proper spec of 150 ft/lbs (200 Nm) and crimp according to procedure in TechConnect. (This torrque is higher than other platforms). Failure to do so will result in eventual Hub & Bearing failure (noise).~

18-075-15

Service Bulletin/Repair Instructions

Flash: Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience the Electronic Vehicle Information Center (EVIC) Fuel Economy display is inaccurate or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? U0140 - Lost Communication With Body Control Module. ? P1D73 - AGS Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P0456 - Evap System Small Leak. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? Improved Enhanced Automatic Oil Change Indicator (EAOCI) system accuracy. ? Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

SB-18-075-15

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

18-006-15 REV-G

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec

18-006-15 REV. G

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec

SB-18-006-15-G

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

08-098-15

Service Bulletin/Repair Instructions

Hands Free Feature Inoperative This bulletin involves updating the Convergence Telematics Module (CTM) software. NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

05-011-15

Service Bulletin/Repair Instructions

Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake rotors, front brake pads, and related hardware. The customer may describe a front brake squeak/squeal high frequency noise in the 6-7 kHz range while stopping, noise may be intermittent (not every stop).

18-009-15 REV-F

Service Bulletin/Repair Instructions

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2016 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0615XX)). 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as

18-009-15 REV-E

Service Bulletin/Repair Instructions

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)). 2015 Dart ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Va

SB18-009-15REV-B

Service Bulletin/Repair Instructions

DODGE DART: VEHICLES MAY REQUIRE ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE WITH LATEST SOFTWARE WHICH INCLUDES VARIOUS DRIVABILITY IMPROVEMENTS *CN UPDATED 11/30/2015 *CN

18-009-15 REV-D

Service Bulletin/Repair Instructions

Flash: 1.4L Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: 2014 Dart ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)). 2015 Dart ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response. ? Engine bump

SB18-009-15REV C

Service Bulletin/Repair Instructions

DODGE: SOME VEHICLES ARE EXPERIENCING VARIOUS SYMPTOMS REGARDING THE MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION BASED ON INVESTIGATION BY TECHNICIAN SUCH AS DIFFICULT TO RESTART ENGINE AFTER WARM/COLD SOAK, DURING EXTENDED HOT IDLE AND/OR LOW SPEED, A/C PERFORMANCE IS POOR, MODERATE/HEAVY ACCELERATION OVER 3500 RPM BUMP SENSATION FELT FROM ENGINE. MODEL 2014-15 DART. *PE UPDATED 11/30/15.

08-080-15

Service Bulletin/Repair Instructions

RE2 RE6 RB5 RB6 Radio Software Enhancements This bulletin involves updating the radio software and navigation if equipped. A customer may experience one or more of the following conditions: ? Radio display screen will lock up and reset intermittently (2013-2014 MY Vehicles). ? Navigation screen goes blank (Software has been updated to better address this condition). ? Navigation system freezes/locks up (Software has been updated to better address this condition). ? Vehicles with Mopar special edition radio, update radio?s splash screen. (2013 Vehicles). ? Incorrect routing directions to fuel stations when using Travel Link. ? Unable to turn on heated seats, icon is greyed out. ? Navigation Icon shows the vehicle going backward when it is moving forward. ? Map Checksum error may be displayed when attempting to update the navigation system maps.

18-006-15 REV-F

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8), built on or before June 16, 2015 (MDH 0616XX). ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14°F to 32°F (-10°C to 0°C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Bod

SB18-006-15REV-D

Service Bulletin/Repair Instructions

CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATION. POWER CONTROL MODULE REQUIRES REPROGRAMMING WITH LATEST SOFTWARE AVAILABLE *CN UPDATED 12/21/15 *CN

18-009-15 REV-C

Service Bulletin/Repair Instructions

Flash: 1.4L MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response (2015 only). ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Black smoke from tail pipe on initial start up during cold ambient temperatures (2014 only). ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)).

18-006-15 REVE

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. In addition, some customers may describe engine flare at startup or idle surge. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (sales codes ED6, ED8), built on or before June 16th, 2015 (MDH 0615XX). ? U0402 - Implausible Data Received From TCM (ED6, ED8). ? Engine Startup Flare and Idle Surge (ED6, ED8). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance (sales codes ED6, ED8). ? P0116 - Engine Coolant Temperature Sensor 1 Performance (sales codes ED6, ED8). ? P050D - Cold Start Rough Idle (sales codes ED6, ED8). 2015 PF Vehicles with (sales codes ED6, ED8), built on or before April 2nd, 2015 (MDH 0402XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10°F to 40°F (-12°C to 4.5°C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance (sales codes ED6, ED8). ? P050B - Cold Start Ignition Timing Performance (sales codes ED6, ED8). ? P050D - Cold Start Rough Idle (sales codes ED6, ED8). ? P061A - Level 2 Torque Performance (sales codes ED6, ED8). ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation) (sales codes ED6, ED8). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off T

18-009-15 REVB

Service Bulletin/Repair Instructions

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response (2015 only). ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Black smoke from tail pipe on initial start up during cold ambient temperatures (2014 only). ? Cold start difficulty below -10C (14F) ambient temperatures. Engine cranks fast and possibly does not start due to loss of crankshaft synchronization until key cycle is performed. (Vehicles built on or after August 23, 2014 (MDH 0823XX) and on or before June 16, 2015 (MDH 0616XX)).

18-006-15 REVD

Service Bulletin/Repair Instructions

Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (sales codes ED6 or ED8), built on or before April 6, 2015 (MDH 0406XX). ? Improve cold engine idle, reduce idle flare up (ED6 only). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance . ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (sales codes ED6, ED8), built on or before April 2, 2015 (MDH 0402XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between °10F to °40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.

D-15-12 RevA

Service Bulletin/Repair Instructions

Fast Feedback Program - Hands Free Module - 2013-2015 Dodge Dart (PF) Rev. A

08-039-15

Service Bulletin/Repair Instructions

Tire Pressure Monitoring System May Display Wrong Tire Location The Body Control Module (BCM) must be reconfigured to a Premium Tire Pressure Monitor System (TPMS). The customer may notice a message ?Low Tire? displayed on the cluster: ? Tire Pressure Monitoring screen on the instrument cluster may indicate the incorrect tire location shown when low tire pressure is detected. ? Example scenario: Right rear tire (RR) may show as low on the instrument cluster when actually it may be left front tire (LF) as being low when a tire gauge is used to check tire pressure. Fig. 1 Low Tire Display On Instrument Cluster

D-15-12

Service Bulletin/Repair Instructions

Fast Feedback Program - Hands Free Module - 2013-2015 Dodge Dart (PF)

18-009-15 REV. A

Service Bulletin/Repair Instructions

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D - O2 Sensor 1/1 Slow Response (2015 only). ? Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. ? DTC P061A - Level 2 torque performance set. ? Engine difficult to restart after cold or warm soak periods. ? Intermittent high coolant temp warning lamp illumination when using cruise control. Condition occurs in conjunction with the P061A DTC listed above. ? Poor A/C performance primarily during extended hot idle and/or low speed driving conditions. Applies to vehicles built with 1234YF refrigerant sales code XFC. ? Black smoke from tail pipe on initial start up during cold ambient temperatures (2014 only).

23-009-15

Service Bulletin/Repair Instructions

Front Window Popping/Clicking Noise While Powered Up Or Down This bulletin involves lubricating the window to regulator attachment point. The customer may describe a popping/clicking noise while powering the right and/or left front door window up or down.

02-004-15

Service Bulletin/Repair Instructions

Cold Temperature Squeak/Creak Noise While Turning The Steering Wheel This bulletin involves applying Nye® lubricant to the front strut mounts. Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4°C (40°F), noise may go away when temperature warms up.

0200415

Service Bulletin/Repair Instructions

18-006-15

Service Bulletin/Repair Instructions

18-006-15 REV. B

Service Bulletin/Repair Instructions

1800615

Service Bulletin/Repair Instructions

1800615REVB

Service Bulletin/Repair Instructions

9002811

Service Bulletin/Repair Instructions

Part Description: IP Center Bezel Issue Description: Please call Mike Wicker at cell (248) 821-9350 before ordering a replacement due to damage OR not fully illuminated IP center bezel. Thank you.

18-006-15 REV. A

Service Bulletin/Repair Instructions

18-009-15

Service Bulletin/Repair Instructions

Flash: 1.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below: ? P0141 - O2 Sensor 1/2 Heater Performance. ? P1D73 - Active Grill Shutter (AGS) Performance. ? P113D- O2 Sensor 1/1 Slow Response (2015 only).

18-061-14 REV. A

Service Bulletin/Repair Instructions

1806114REVA

Service Bulletin/Repair Instructions

1806114a

Service Bulletin/Repair Instructions

18-066-14

Service Bulletin/Repair Instructions

Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the Diagnostic Trouble Codes (DTCs) listed below Set in the PCM. P0141 - O2 Sensor 1/2 Heater Performance P1D73 - Active Grill Shutter (AGS) Performance P113D- O2 Sensor 1/1 Slow Response (2015 only)

1806614

Service Bulletin/Repair Instructions

Diagnostic and System Improvements

08-085-14

Service Bulletin/Repair Instructions

Hands Free Feature Inoperative This bulletin involves updating the Convergence Telematics Module (CTM) software.Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: U11F6-00 Lost Communication With Convergence Telematics Module. U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

08-085-14 REV. A

Service Bulletin/Repair Instructions

08-085-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

0808514

Service Bulletin/Repair Instructions

This bulletin involves updating the Convergence Telematics Module (CTM) software

18-040-14 REV. A

Service Bulletin/Repair Instructions

Flash: Diagnostic And System Improvements For P219A And Or P106A This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P219A - Bank 1 Air-Fuel Ratio Imbalance.

18-040-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

1804014

Service Bulletin/Repair Instructions

08-081-14

Service Bulletin/Repair Instructions

MIL Illumination DTC U11E9 After Fascia Removal This bulletin involves confirming that the Active Grille Shutter (AGS) electrical harness connector is properly connected.

0808114

Service Bulletin/Repair Instructions

MIL Illumination DTC U11E9 After Fascia Removal This bulletin involves confirming that the Active Grille Shutter (AGS) electrical harness connector is properly connected.

08-059-14 REV. A

Service Bulletin/Repair Instructions

Flash: RE2 RE6 RB5 RB6 Radio Software Enhancements This bulletin involves updating the radio software. A customer may experience, one or more of the following conditions: ? Incorrect routing directions to fuel stations when using Travel Link. ? Unable to turn on heated seats. Icon is greyed out. ? Radio display screen will lock up and reset intermittently. ? Navigation screen goes blank. ? Navigation system freezes/locks up. ? Navigation Icon shows the vehicle going backward when it is moving forward. ? Map Checksum error may be displayed when attempting to update the navigation system maps.

08-059-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

0805914

Service Bulletin/Repair Instructions

18-032-14 REV. A

Service Bulletin/Repair Instructions

Flash: MIL Illumination. Includes Various Drivability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A customer may experience one of more of the following conditions: Engine bump sensation felt during moderate to heavy acceleration over 3500 RPM. DTC P061A- Level 2 torque performance set Engine difficult to restart after cold or warm soak periods. Condition occurs in conjunction with the P061A DTC listed above. Applies to vehicles built with 1234YF refrigerant sales code XFC.

18-032-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

17-004-14

Service Bulletin/Repair Instructions

Right Rear Spring Shifted In Upper Isolator And Possible Clunk Noise This bulletin involves verifying the customer?s symptom/condition and if necessary, replacing the rear suspension springs. Right side rear suspension spring is shifted in the upper spring mount isolator and possibly a clunk noise can be heard or felt coming from the rear of the vehicle, while going over bumps.

18-040-14

Service Bulletin/Repair Instructions

Flash: MIL Illumination P219A- Bank 1 Air-Fuel Ratio Imbalance This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P219A - Bank 1 Air-Fuel Ratio Imbalance

08-059-14

Service Bulletin/Repair Instructions

18-034-14 REV. A

Service Bulletin/Repair Instructions

P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

18-034-14

Service Bulletin/Repair Instructions

SB-18-034-14

Service Bulletin/Repair Instructions

ON SOME MODEL VEHICLES AND JEEPS, (MY 2013-2014)MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATES AND DIAGNOSTIC TROUBLE CODE (DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

18-032-14

Service Bulletin/Repair Instructions

Flash: MIL Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P061A- Level 2 torque performanceCustomers may also experience any of the following symptoms: Engine difficult to restart after cold or warm soak periods. (This condition occurs in conjunction with the P061A DTC listed above). (Applies to vehicles built with 1234YF refrigerant (sales code XFC)).Updating the PCM software will correct the conditions listed above.

1803214

Service Bulletin/Repair Instructions

MIL Illumination. Includes Various Driveability Improvements

No83

Service Bulletin/Repair Instructions

MasterTech Updates

9003081

Service Bulletin/Repair Instructions

Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

08-041-14

Service Bulletin/Repair Instructions

Flash: Steering Wheel Vibration At Highway Speeds On Smooth Road This bulletin involves road testing and updating the software in the Electric Power Steering (EPS). If required road force balancing and match mounting the tires and wheels. NOT be mistaken for a normal tire vibration felt in the seat and steering wheel or at low speeds.

18-024-14

Service Bulletin/Repair Instructions

Flash: Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following condition: EVIC Fuel Economy display is inaccurateThe following system improvements have also been included in this software release: Improved Enhanced Automatic Oil Change Indicator(EAOCI) system accuracy Corrected a generic scan tool display issue regarding Mode 6 data accuracy

1802414

Service Bulletin/Repair Instructions

Various Driveability Improvements

08-022-14 REV. A

Service Bulletin/Repair Instructions

Flash: Cluster Displays Service Battery Message This bulletin involves updating the software in the Body Control Module (BCM). The customer may notice a ?Service Battery? message is displayed in the Electronic Vehicle Information Center (EVIC). This message is most likely to be displayed when the outside temperatures are colder. On further inspection no DTC?s will be found.

08-022-14REV.A

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

08-022-14

Service Bulletin/Repair Instructions

18-011-14

Service Bulletin/Repair Instructions

Flash: MIL Illumination P2251- O2 Sensor 1/1 Negative Current Control Circuit Open This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open

21-012-13

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

D-13-33

Service Bulletin/Repair Instructions

SUMMARY TO BE PROVIDED ON A FUTURE DATE.

9002519

Service Bulletin/Repair Instructions

82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Reading this report

Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.