114537
Service Bulletin/Repair Instructions
EVAPORATOR - AIR CONDITIONING
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
114537
EVAPORATOR - AIR CONDITIONING
114538
EVAPORATOR - AIR CONDITIONING
9100898
Engine PNs: MY 24-26 WD/DT (5.7L) Code P00B is being misdiagnosed and incorrect parts are being installed causing over repair. Refer to SOL S2609000006 The IAFM Foam Engine Valley Cover (PN 53013735AB) does not provide sufficient clearance for proper routing of the MDS solenoid jumper harness (PN 05148163AE). As a result, the harness may become compressed by the foam cover. To prevent unnecessary part replacement, the MDS solenoid jumper harness (PN 05148163AE) should be inspected for damage or pinch conditions prior to replacing the following part numbers: Engine PNs: 68409343AA 68409357AA 68450915AA OCV PNs: 53022338AB Phaser PNs: 53022298AA 53022298AB
9100900
Passive Entry O/S Dr Handle Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S2623000016 REV.A
Lift Gate Latch And Glass Replacement / Servicing.
08-319-26
Flash: Adaptive Cruise Control (ACC) Module Update Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ● C14A4-00 - Sensor Adjustment Required. Customers may also experience the following: ● "ACC/FCW Unavailable, Service Required" message in the Instrument Panel Cluster (IPC). This bulletin involves reprogramming of the ACC module with the latest available software.
9100883
Glass Assy - Liftgate Prior to replacing the rear liftgate glass, perform Star Online S2623000016.
113803
HOSE AND TUBE - HEATER SUPPLY AND RETURN
08-296-26
Global Telematics Box (TBM) Firmware Over Customers must experience a Malfunction Indicator Lamp (MIL) illumination and one or more of the SYMPTOM: following Diagnostic Trouble Codes (DTCs): ● B22A9-96 - ECU Internal Performance-Component Internal Failure. ● B1560-11 - Cellular Antenna 1-Circuit Short To Ground. ● B1560-13 - Cellular Antenna 1-Circuit Open. ● B1561-11 - Cellular Antenna 2-Circuit Short To Ground. ● B1561-13 - Cellular Antenna 2-Circuit Open. ● B1562-14 - GPS Antenna-Circuit Short To Ground Or Open. Customers may also experience the following: ● "UConnect Box Requires Service" Message in Radio Display.
14-007-26
Extended Crank Condition Due To Loss of Fuel Pressure Customers may experience the following: SYMPTOM: ● Extended engine crank condition. This bulletin involves performing a fuel pressure test and possibly replacing the fuel pressure regulator.
9100833 REV1
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
9100857
Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for any bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way. This GPOP applies to 2021-2022MY WK & 2021-2025MY WD vehicles with extended crank condition due to loss of fuel pressure. Do not replace FDM. Reference TSB 14-004-25 REV B. There is a Fuel Pressure Regulator kit to address this issue.
S2508000025 REV. B
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
113152
THERMOSTAT – NONE.
113153
THERMOSTAT – NONE.
08-256-26
Uconnect® Screen Turns Blank Or Black Customers may experience the following: SYMPTOM: ● The Uconnect® screen display goes blank/black at times.
S2208000045 REV.D
Backup Camera Poor Image Quality Inspection
S2508000025 REV.A
Instrument Panel Cluster (IPC) and Radio Compass Display has Dashes (--)
9100848
If the Driver/Passenger Seat Adjsuter Switch is inoperable, seat back will not move or seat moves on its own: 1.Which function is not operating properly? *Forward/Backward *Recline Forward *Recline Backward *Height Adjustment *Multiple Functions 2.Is the concern constant or Intermittent? 3.If intermittent, how often does it occur? Daily, Weekly, Randomly 4.Does the seat move on its own without pressing any switch? Yes / No 5.Does the issue occur only while driving, only at key-on, or while the vehicle is parked? 6.Has the concern occurred after the vehicle has been sitting for an extended period (overnight or several hours)? 7.Does pressing the switch multiple times temporarily restore operation? 8.Have any other seat functions or electrical features been affected at the same time? 9.Has the seat adjuster switch or seat assembly been previously repaired or replaced? Before replacing the seat adjuster switch, verify power, ground, connector engagement, wiring integrity, and inspect for blown fuses or damaged harnesses. If no external issues are found and the concern is verified, an intermittent internal switch failure should be considered.
9100850
When dealers search for WD (68530334AA) or RU (68227397AH) analog rear view camara part number for a repair/replacement part, we want to notify them to review Star Online S2208000045 before replacing cameras for poor image quality (fuzzy, blurry, pixelated) to ensure camera replacement is warranted / justified. This SOL provides a process for evaluating if the camera's image quality is within a typical range.
S2623000041 REV.A
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A
112845
WIRING – INJECTOR
9100833
Fuel Delivery Module Before replacing the fuel module for DTCs P0461 and P062A and other not start, long crank, fuel gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.
S268A000014
Radio/ETM is Adding Approximately 27mA Draw to Vehicle When in Logistics Mode
S1623000028 Rev. K
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2624000006
Blower Motor Makes Loud Noise
9100835
Prior to replacing an inoperative passive entry door handle, perform Star Online S2623000040.
S1623000028 REV.J
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2623000040
Passive Entry Exterior Door Handle Inoperative When Touched To Lock And Or Unlock.
S2623000041
Power Liftgate Intermittently Inoperative. Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.
05-001-26 REV. A
Application Of Grease In Pads/Clips Customer may experience one or more of the following: ● Brake pulsation/vibration. ● Squealing/squeaking/grinding noise when braking. ● Vehicle pulls to one side when braking. This bulletin involves lubricating the brake pad anchors.
S1623000028 REV.I
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2408000018 REV.B
New Key Will Not Program, 0x22 Scan Tool Error
112191
COOLER - ENGINE OIL
112192
COOLER - ENGINE OIL
08-208-26 REV. A
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
111833
SENSOR – KNOCK
111834
SENSOR – KNOCK
S2608000024
Intermittently Vehicle Will Not Shift Out Of Park Position.
08-208-26
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
08-207-26
Instrument Panel Cluster (IPC) Flicker Turn By Turn The customer may experience flickering on their Instrument Panel Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay
08-191-26
Flash: Radio Frequency Hub Module (RFHM) Updates This software enhancement includes: ● Update to the RFHM software to prevent unauthorized key fob programming This bulletin involves **inspecting and possibly** updating the RFHM module with the latest available software
S2308000034 REV.B
No Wireless Charging Or Slow Wireless Charging
S2609000006
P000B Bank 1 Cam 2 Position Slow Response - Malfunction Indicator Light (MIL) - Check Engine Light (CEL)
9100800
Multiple cluster/EVIC issues if misdiagnosed can lead to unnecessary IPC replacement. Tech Tip: Reset the IPC module first before any steps are taken to replace the module are undertaken. Connect Witech to the vehicle. Reset all DTCs and check for active DTCs warnings set against IPC. If battery low indicated against IPC, reset the module via WiTech tool. NOTE: After Battery Drainage, the IPC may not function correctly. Please follow the following steps before considering an IPC replacement: 1) Charge the Battery Ensure the battery is fully charged. 2) Soft Reset Perform a soft reset on the IPC. 3) Power-Up Issue 4) If the IPC does not power up, proceed with the following steps: a. Disconnect the battery. b. Reconnect the battery. 5) If condition still exists, consider IPC replacement.
S2408000018 REV.A
New Key Will Not Program, 0x22 Scan Tool Error
07-002-26
Rear Heater Coolant Tube Repair Customers may comment on one or more of the following: SYMPTOM: ? A coolant leak or fluid appearing from under the vehicle. ? Elevated engine coolant temperature and/or indication of overheating. This bulletin involves insp
111405
COVER - CYLINDER HEAD
111406
COVER - CYLINDER HEAD
S2623000023
Power Liftgate Inoperative.
S1623000028 REV.H
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S2223000022 REV.E
Power Liftgate Inoperative Or Intermittently Will Not Open Or Close.
S2605000003
Front Brake Noise, Inboard Pad Wear, Brake Pull.
S2623000016
Lift Gate Latch And Glass Replacement / Servicing.
18-044-26
Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) ● P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) ● P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) ● P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) ● P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) ● P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) ● P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) ● P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) ● P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) ● P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** ● P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** ● P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** ● P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** ● P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** ● P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: ● **Oil Level High Warning in the Instrument Panel Cluster (IPC).** ● Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi
S2608000015
Memory Seat Does Not Work There Is No Response from The Seat While Pressing the Memory Seat Profiles from the Switch Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration
S2208000045 REV.C
Backup Camera Poor Image Quality Inspection
S2523000014 REV.A
2 nd Row Seat Difficult To Latch.
S2608000012
The Customer May Experience Any Rear Window Inoperable from Its Respective Switch or The Driver Master Switch
S2621000003 REV.A
The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
S2608000010
Active Diagnostic Trouble Code (DTC) B1A10-00, B1A11-00, B1A12- 00, B1A13-00-, B1A14-00, B1A15-00, B1A16-00, and B1A17-00 in The Radio Frequency Hub (RFH)
23-005-26
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: SYMPTOM: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
110603
SPEAKER - NONE
110604
SPEAKER - NONE
110560
HOSE - ENGINE COOLANT TO OIL COOLER INTLET
S2621000003
Service transmission/check engine warning indicator for the 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV transmissions that have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
110447
WATER PUMP
110448
WATER PUMP
S228A000025 REV.A
Harman R1H Uconnect 5 Radio Software Flash Error Codes
S268A000008
Uconnect Box Requires Service, Please Visit an Authorized Dealer Message on Display Message With DTCs B1498-13, B1498-19 or B1570-93
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S2623000006
Washer Fluid Warning Lamp Illuminated When Reservoir Is Full
S2624000001
Ticking Noise From Rear HVAC Blower
S2308000120 REV.F
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
S2607000002
Hemi Water Pump Coolant Leak Inspection
109724
Water Pump & Chain Case Cover
109727
Water Pump & Chain Case Cover
08-012-26
Speaker Diagnostic Procedure Rattle, buzz and squeak coming from specific speakers.
S2308000120 REV.E
Rain Sensing Auto Wipers and Auto on Head Lamps Inoperative. Rain Sensor Internal Failure.
S2408000114 REV.B
Instrument Panel Cluster (IPC) Displays Warning Lamps or Messages for Loss of Advanced Driver Assist System (ADAS)
08-394-25 REV. A
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present Technicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure.
08-398-25
Flash: Radio Frequency Hub Module (RFHM) Updates his software enhancement includes: ● Update to the RFHM software to prevent unauthorized key fob programming This bulletin involves updating the RFHM module with the latest available software.
08-396-25
Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.Drivetrain Control Module (DTCM) Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): ● C1403 - 92 Transfer Case Range Position Sensor - Performance Or Incorrect Operation. ● U0403 - 00 Implausible Data Received From Transfer Case. Customers may experience the following: ● Service 4WD Light On in Instrument Panel Control (IPC) This bulletin involves replacing the DTCM.
9100734
If the DTC B1E21-96: Backup Battery-Component Internal Failure is active and customer states Popup message will show at the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347
08-394-25
Telematics Box Module (TBM) Backup Battery Replacement When DTC B1E21 Is Present echnicians may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● B1E21-96 - Backup Battery Component Internal Failure
108546
ISOLATOR - ENGINE MOUNT
S258A000021
Diagnostic Trouble Code (DTC) B15A1-00 Media Port Connection 1 Connection Found Set.
108840
Hose- Oil Cooler Inlet, Outlet
108547
ISOLATOR - ENGINE MOUNT
S2423000012 REV.D
Power Liftgate Is Inoperative or Won’t Close.
S2308000034 REV.A
No Wireless Charging Or Slow Wireless Charging
S2508000100
Intermittent Uconnect Box Requires Service Message. TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562
S2509000009
Engine Oil Leak
S2505000011
Poor Brake Pedal Feel After Recent Repair. Pedal Travel And Or Excessive Pedal Travel.
S2523000084
Tick Click Snap Noise With Chassis Flex From Front Wheel Area While Driving.
107614
EVAPORATOR - AIR CONDITIONING & CORE - HEATER
9100670
Data collection required for all 2020-2026MY vehicles with 3.6L PSU engines during any of their first 3 engine oil changes. This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.
9100659
Rear storage lid (5LC38TRMAK) can stick against rear scuff when opening and closing. If issue presents itself, disassemble and reassemble the cargo lid with seat in down position. Doing will most likely reset positioning and allow for there to be no interference of the cargo lid and rear scuff.
23-008-25 REV. A
Exterior Front Lamps Condensation Clearing Procedure *Some customers may report that on occasion vehicle exterior front lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*
9100671
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.
S2508000072
Service Shifter Message Displayed on the Instrument Panel Cluster (IPC), Unable to Move the Shifter Out of Park
02-002-25 REV. A
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
S2508000070
Service Park Assist Message Displayed on The Instrument Panel Cluster (IPC), Park Assist System Inoperative
14-004-25 REV. B
Extended Crank Condition Due To Loss of Fuel Pressure Customers may experience the following: ● Extended engine crank condition. This bulletin involves performing a fuel pressure test and possibly replacing the **fuel pressure regulator**.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
S2508000063
Passive Entry Does not Lock or Unlock Vehicle
S258A000019
Radio Does Not Turn On Automatically When Vehicle Is Started
08-235-25
Blind Spot Detector May Not Work Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● U11FB-00 - Lost Communication With Left Blind Spot Sensor. ● U11FA-00 - Lost Communication With Right Blind Spot Sensor. Customers may experience the following: ● Blind spot system off/service blind spot system/blind spot temporarily unavailable warning lights on in Instrument Panel Cluster (IPC). ● Blind Spot Monitoring inoperative. This bulletin involves replacing the rear fascia wiring.
S258A000017
Door speaker Inoperative or No Sound
S2509000001 REV.B
Engine Rattle Noise
23-006-25 REV. B
Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield.
S2523000069
Inspection Procedure For Liftgate Gas Strut
106075
PAD KIT - FRONT DISC BRAK
21-009-25 REV. C
850RE D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2208000138 REV.B
Decreased Remote Start And RKE Range. Tire Pressure Sensors Values Are Not Displayed
9100622
When replacing a camshaft and parts kit (P/N 68661146xx and/or 68661147xx), it is NOT necessary to order the roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.
S2523000063
Front Cradle Service Update
9100614
ADJUSTER Valve Lash Customer's complaint may include a ticking noise coming from the engine. Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.
105287
PAD KIT - FRONT DISC BRAKE
9100599
Underhood start/stop safety The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.
02-002-25
Shock And Strut Diagnosis And Replacement Guidelines Leaking, noisy, or weak shocks or struts.
9100588
Telematics Box Module: Verify Z part number availability. Order a Z part number for all Exchange Orders:Warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.
09-011-25
Misfire Diagnostic Trouble Codes (DTCs), Rough Idle, Valvetrain Noise Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0301 - Cylinder 1 Misfire. ● P0302 - Cylinder 2 Misfire. ● P0303 - Cylinder 3 Misfire. ● P0304 - Cylinder 4 Misfire. ● P0305 - Cylinder 5 Misfire. ● P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: ● Rough idle. ● Valvetrain noise.
S2323000002 REV.A
Washer Light On And Will Not Turn Off After Adding Washer Solvent.
9100498 Rev 3
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.
9100570
Transmission Fluid Please note fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Visible "glitter" or debris in the pan does not justify complete unit replacements.
S2408000114 REV.A
Instrument Panel Cluster (IPC) Displays Warning Lamps or Messages for Loss of Advanced Driver Assist System (ADAS)
58B Combo Rev2
CUSTOMER SATISFACTION NOTIFICATION NORTH AMERICA 58B Collant Restrictor
104524
HOSE - RADIATOR OUTLET
S2523000031
C14A4-00 Sensor Adjustment Required Set In Adaptive Cruise Control Module (ACC).
21-009-25 REV. B
850RE D Clutch Repair **Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.
S2408000015 REV.D
Remote Keyless Entry (RKE) Functions Do Not Work, Intermittent Vehicle Response When Using the RKE, Key Not Programmed, Adding Remote Start
S2509000004
Misfire DTCs, Rough Idle, Valvetrain Noise
S2509000001 REV.A
Engine Rattle Noise
9100471
CANISTER Vapor -If an issue is detected with the Evaporative System Integrity Module (ESIM) Detector and not the Vapor Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM.
103801
HOSE AND TUBE - HEATER SUPPLY AND RETURN
103833
HOSE AND TUBE - HEATER SUPPLY AND RETURN
S2509000002
Engine Noise
S258A000009
Apple CarPlay Does Not Complete The First Initial Wireless Connection.
S2123000084 REV.A
1st Row Seat Belt Retractor D-Ring Is Binding And Not Able To Rotate
S2523000014
2 nd Row Seat Difficult To Latch.
14-004-25 REV. A
Extended Crank Condition Due To Loss of Fuel Pressure Customers may experience the following: ● Extended engine crank condition. This bulletin involves performing a fuel pressure test and possibly replacing the fuel pump module.
9100498 REV 1
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.
9100461 REV 1
2nd row headrest 2024 WD 2nd row headrest BSR/rattles - Adjust headrest rods before replacing headrest or mechanism.
S2108000015 REV.J
Uconnect Box Require Service Message
9100500
Touchscreen For all infotainment system repairs (touchscreens, radios, etc.), refurbished parts may be available. Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process
S2509000001
Engine Rattle Noise
S2523000009
Buzz Squeak Rattle (BSR) From 2 nd Row Headrest Area While Driving.
103288
CAMERA - REAR VIEW
103289
CAMERA - REAR VIEW
103293
HOSE - RADIATOR OUTLET
09-003-25
Oil Leaking From Oil Filter Area Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: ● Oil found on the ground beneath the vehicle.
S258A000006
Rear ParkView Backup Camera Guidelines Not Appearing On Radio
23-008-25
Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses.
S228A000005 REV.E
Uconnect Box Error Message, With Active or Stored Cellular Antenna Open or Short Diagnostic Trouble Codes (DTCs)
101791
MODULE KIT - FUEL PUMP/LEVEL UNIT
9100498
3.6L PSU Long Block Misfire DTC codes and/or rough idle and/or valvetrain noise. These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets).
S2508000013
The Cluster Electronic Vehicle Information Center (EVIC) Displays “ACC/FCW Unavailable Service Required”, “Adaptive Cruise Control (ACC) System is Disabled”
21-009-25 REV.A
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch
9100494
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
102854
Warranty Newsletter – Volume 11, Issue 1
102855
FCA Caribbean Warranty Newsletter – Volume 11, Issue 1
21-009-25
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: ● Transmission slips when shifting. ● Vehicle will not move in reverse. ● Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
101790
BUCKLE ASSY - BUCKLE ASSYS/BELT
9100461
2nd row headrest 2024 WD 2nd row headrest BSR/rattles - Adjust headrest rods before replacing headrest or mechanism.
09-022-24 REV. A
Engine Oil Cooler Leak Customers may comment on one or more of the following: ● Vehicle overheats. ● Coolant overflow recovery bottle contains milky fluid. ● Coolant found leaking under the vehicle. ● Engine oil cooler is leaking. This bulletin involves installing a coolant flow restrictor and possibly replacing the engine oil cooler.
21-039-24 REV. H
D Clutch Repair Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0733-00 - Gear 3 Shift Incorrect Ratio. ● P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. ● P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch
S2208000045 REV.B
Backup Camera Poor Image Quality Inspection
101689
WEATHERSTRIP - FRONT DOOR BELT OUTER
S2423000012 REV.C
Power Liftgate Is Inoperative or Won’t Close.
101290
GEAR - RACK AND PINION
101327
GEAR - RACK AND PINION
S228A000017 REV.A
Battery Drain Suspected or "Identified" From USB or Media Hub
S2408000098
ACC Sensor Blinded, “ACC Unavailable Service Required” “FCW Unavailable Service Required”, Adaptive Cruise Control (ACC) system disabled, Loss of Advanced Driver Assist System (ADAS) Features Messages Displayed on the Instrument Panel Cluster (IPC)
S2423000040
Passenger Door May Not Unlock Or Lock. U0200 Set.
9100404
SWITCH AND BEZEL Front Door Before replacing the driver window switch, please follow these steps: 1.- Review the master window Switch for any physical issue (Button stuck, broke). If no physical issue identified, move to next steps. 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch.
99500
CARRIER – PLANETARY & SHAFT KIT - OUTPUT
S2408000066
Drained Battery, Low System Voltage, Battery Not Charging, High System Voltage
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
98322
STEP KIT - TUBULAR SIDE
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.