U67 Combo Rev11
Warranty Program/Extension
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
U67 Combo Rev11
Emissions Recall U67 - Catalytic Converter Efficiency - Dealer Notification (Revision 11)
9100653
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
106241
LAMP - DOME
104974
LAMP - DOME
103774
LAMP - DOME
103954
ACTUATOR - A/C AND HEATER
104087
ACTUATOR - A/C AND HEATER
103617
STARTER - ENGINE
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357A
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357a
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
9003357
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
U67 Combo Rev10
Emissions recal U67 Catalytic Converter Efficiency
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
U67
Some of the above-involved vehicles may exceed NOx (Oxides of Nitrogen) emission level standards due to loss of catalytic converter efficiency
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
9004206
Remanufactured Transmission Assembly 1. All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when
1804616
Powertrain Diagnostic And System Enhancements
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
9004509
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
9004330
PLATE, TORQUE CONVERTER DRIVE For 3.6L with 62TE NOTE: FOR ALL PROMASTER (VF) 3.6L/62TE EQUIPPED VEHICLES: IF THE TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
S1809000007 Rev.
Customer Complaint May Include Engine Oil Leak Or Consumption
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S2008000113
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S2008000113 Rev.
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S2121000005
62TE 6-Speed Transmission Cracked Torque Converter (TC) Piston Repair Index, To Aid In Diagnosis And Repair
71055
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. B)
23-027-20 REV. A
Active Head Restraint (AHR) Inadvertent Deployment - X84 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.
70316
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2012-2018 Dodge Journey (JC) and 2012-2014 Dodge Avenger/Chrysler 200 (JS) (Rev. A)
69912
Warranty Bulletin D-20-16 (X84) Active Head Restraint - Select 2010-2018 Dodge Journey (JC) and 2010-2014 Dodge Avenger/Chrysler 200 (JS)
23-027-20
Active Head Restraint (AHR) Inadvertent Deployment - X84 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
2302720
Active Head Restraint (AHR) Inadvertent Deployment - X84 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
S1908000028 Rev.
(Rev. A) Power Inverter Load Ratings
S1908000102
(Rev. A) Power Inverter Load Ratings
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1121000006 Rev.
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
S1121000006RevA
(Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
9004268
THROTTLE BODY For clarification, only use 68414676A$ on 2010 & earlier vehicles as supply is limited.
9004239
CABLE, Latch Release, Track to Recliner, Left Prior to replacing for any kind of damage or functional concern , please take photos of the condition and/ or issue with seat cable before disassembly, Please email pictures of cable including part number to FCA Redacted Content; please include dealer contact information for follow up. If no response in 15 minutes, proceed with repair.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
S1508000480
Speed Control Operates Intermittently
S2008000027
Vehicle Does Not Start, No Crank
18-058-19 REV. B
No Start After Powertrain Control Module (PCM) Replacement and/or Reprogramming
V51
Customer Satisfaction Notification V51 Reprogram Powertrain Control Module
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
08-083-19
Flash: Hands Free Module (HFM) Software Enhancements This bulletin involves reprogramming the HFM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003801
Evaporative Purge System Parts MIL On ? P0456: If fault code P0456 is active, contact Manuel Gandara on cell: (248) 622-8109 before performing repair service. If you do not receive a response within 15 minutes, please continue with the normal repair procedure.
T12
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
18-081-17
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.This bulletin applies to vehicles within the following markets/countries: NAFTA, LATAM, EMEA and APAC. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory:2.4L EngineP0335 - Crankshaft Position Sensor Circuit. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P1607 - PCM Internal Shutdown Timer Rationality - (Powertrain Control Module). P2610 - PCM Internal Engine Off Timer Performance - (Powertrain Control Module). P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P0443 - EVAP Purge Solenoid Circuit. P0116 - Engine Coolant Temperature Sensor Performance. P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. U0140 - Lost Communication With Body Control Module (BCM). Customers may also notice one or more of the following symptoms:When coming to a stop or making a turn, their vehicle would suddenly shutoff. Mostly noted in high ambient conditions greater than 40° C (105° F)(ED3 Engine only). A hesitation/surge feel that some customers might note it feels like misfire at 65-110 kph (40-70 mph) in 4th gear lock up(ED3 Engine only). In addition, the following software enhancements are available:Start Improvements for cold or high altitude starts when using E15 fuel(ED3 Engine only). 3.6L EngineP0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak. P0300 - Multiple Cylinder Misfire. P000A - Bank 1 Camshaft 1 Position Slow Response. P000B - Bank 1 Camshaft 2 Position Slow Response. In addition, the following software enhancement is available:Improved shift quality.
9002201
Cargo and floor cargo organizer storage bin and latch Please note that for both the cargo area bin/lid and floor cargo organizer; latches are serviceable separately. You do not need to replace the entire bin or lid for this, the following part numbers are for the cover latches: 1CB78DK7AA 1CB78XDVAA Failure to follow this could result in a dealer chargeback
9003666
Console, Overhead For concerns with the Overhead Sunglass Bin (regardless of LED or incandescent lighting), please contact: Marco Rodriguez at (248) 941-8623 prior to replacing the component. If you do not receive a response within 15 minutes, please continue with normal repair procedure.
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
25-003-16 REV. A
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
08-091-16
Flash: Instrument Panel Cluster (IPC) Enhancement This bulletin involves reprogramming the IPC with the latest available software. The customer may describe that inside the IPC display, the spelling of the word ?Trip? is misspelled ?Viajem?.The following software enhancement is available: This software will correct the spelling of the word ?Trip? in the display of the IPC.
2500316
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
68234120
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A for an exchange or 05064993A for a new part replacement. Prior to replacing parts, Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~ ~______________________________________~ Contact Us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. DO NOT email regarding repair procedures unrelated to this Tech Tip or part order inquires. Please include the Part Number (s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
68141352A$
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.
68234120A$
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.
S18 v.2
NOTE: S18 originally published in July. Manverter changed to Maniverter. Alternate Transportation section wording revised. Customer Satisfaction Notification S18 - Engine Oil Consumption The engine on about 480 of the above vehicles may experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.
04726431A
Wheel Assy - steel When servicing a JOURNEY (JC) vehicle with steel wheels (WFU code) with or without a shake or vibration complaint; please review the 4 wheel assemblies in order to detect any witness mark of a missing/misplaced wheel weight. Also please try to remove the weights with hand force only. Please inform Karla De La Rosa Munive (karla.delarosa@fcagroup.com) how many witness marks were seen, and how many weights were able to be removed with force hand,on each wheel assembly. ~ Please contact karla.delarosa@fcagroup.com for feedback related ONLY.
04726431A$
Wheel Assy - steel When servicing a JOURNEY (JC) vehicle with steel wheels (WFU code) with or without a shake or vibration complaint; please review the 4 wheel assemblies in order to detect any witness mark of a missing/misplaced wheel weight. Also please try to remove the weights with hand force only. Please inform Karla De La Rosa Munive (karla.delarosa@fcagroup.com) how many witness marks were seen, and how many weights were able to be removed with force hand,on each wheel assembly. ~ Please contact karla.delarosa@fcagroup.com for feedback related ONLY.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
RL305553A
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
S18
Customer Satisfaction Notification S18 - Engine Oil Consumption The engine on about 480 of the above vehicles may experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
0900616REVA
2.0L Or 2.4L Long Block Replacement
68234120A
Panasonic 8.4" CTP/FCTP Radio, Update Failure Issue 1: Hand Free Module inoperative, can't pair phone: - Do not replace the radio for phone issues. The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~
09-006-16
2.0L Or 2.4L Long Block Replacement This bulletin involves replacing the long block due to incorrect machining operation on the cylinder head. The customer may describe the engine is consuming oil.
0900616
2.0L Or 2.4L Long Block Replacement This bulletin involves replacing the long block due to incorrect machining operation on the cylinder head. The customer may describe the engine is consuming oil.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
18-046-16
Flash: Powertrain Diagnostic And System Enhancements. This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The customer may describe the following: · **Poor engine response to accelerator pedal request above between 4,500 m (14,760 ft) and 5,200 m (17,056 ft).** The PCM software also includes: · Release of a required V-1 software update that meets Euro IV Emissions for the China specific test weight class.
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
18-033-16
Flash: Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2.4L Engine · **P0335 - Crankshaft Position Sensor Circuit. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P1607 - PCM Internal Shutdown Timer Rationality - (Powertrain Control Module). · P2610 - PCM Internal Engine Off Timer Performance - (Powertrain Control Module). · P0456 - EVAP System Small Leak.** · P0441 - EVAP Purge System Performance. · P0443 - EVAP Purge Solenoid Circuit. · P0116 - Engine Coolant Temperature Sensor Performance. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. · U0140 - Lost Communication With Body Control Module (BCM). In addition, the following software enhancement is available: Improved alternator control at idle. 3.6L Engine · **P0335 - Crankshaft Position Sensor Circuit. · P2610 - PCM Internal Engine Off Timer Performance. · P0456 - EVAP System Small Leak.** · P0300 - Multiple Cylinder Misfire. · P000A - Bank 1 Camshaft 1 Position Slow Response. · P000B - Bank 1 Camshaft 2 Position Slow Response. In addition, the following software enhancement is available: Improved shift quality.
1803316
Diagnostic And System Improvements.
31-001-16
Do Not Apply Corrosion Protection On Sheet Molding Compound (SMC) Plastic Panels This bulletin involves discussing SMC plastic panels and applying corrosion protection.
0801416
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
R61 (15V-675)
Antilock Brake System Control Module Anti-Lock Brake System (ABS) control module on about 275,600 of the above vehicles may have a ground wire eyelet on the right front shock tower that allows water to wick through the ground wire case and into the ABS module. Moisture in the ABS module could disable the ABS and/or Electronic Stability Control (ESC) system(s). The lack of a functioning ABS and/or ESC system(s) could change the braking and/or handling characteristics of the vehicle and cause a crash without warning.
R65
The radio navigation system on about 30,300 of the above vehicles may experience a condition which permanently renders the navigation features not functional as a result of memory corruption.
1RH65DX8A
Parts.
53034160A
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
05184349A
Before replacing this part for debris issue faults, please call the following people;~ Engineering is seeking information regarding this part.~ Bob Smith ? Cell (248) 202-9458 - Robert.M.Smith@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
04800696A
Part Description: Flex Plate Issue Description: If the part you are replacing is cracked; FCA would like to have the transmission replaced with the flexplate. Please call Jian Zhu on his cell (248) 379-1132.
08-033-15 REV B
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank (Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only) (Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone aft
0803315REVB
This bulletin involves updating the radio control head software and navigation if equipped.
23-043-15
Liftgate Contacts Roof This bulletin involves adjusting the liftgate hinge. Liftgate contacts roof
68082365A
Part Description: Continental RHA/REB CTP 4.3" Issue Description: Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The RHA/REB radios have a seperate display called the Integrated Center Stack (ICS) provided by Alpine. If attempting to replace the ICS, do not order a radio part number. Instead, order p/n Z5064976A$ for an exchange or 05064976A$ for a new part replacement
68082365A$
Part Description: Continental RHA/REB CTP 4.3" Issue Description: Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The RHA/REB radios have a seperate display called the Integrated Center Stack (ICS) provided by Alpine. If attempting to replace the ICS, do not order a radio part number. Instead, order p/n Z5064976A$ for an exchange or 05064976A$ for a new part replacement
21-056-15
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a harsh 3-1 downshift.
04800696A$
Part Description: Flex Plate Issue Description: If the part you are replacing is cracked; FCA would like to have the transmission replaced with the flexplate. Please call Jian Zhu on his cell (248) 379-1132.
18-014-15 REV-A
Flash: 3.6L Or 2.4L Diagnostic and System Improvements This bulletin involves updating the Powertrain Control Module (PCM) software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. 2.4L Engine ? P0441 - EVAP Purge System Performance. ? P0443 - EVAP Purge Solenoid Circuit. ? P0456 - EVAP System Small Leak. ? P0116 - Engine Coolant Temperature Sensor Performance. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. ? U0140 - Lost Communication With Body Control Module. ? Improve alternator control at Idle. 3.6L Engine ? Improved shift quality. ? U0140 - Lost Communication With Body Control Module. ? P0300 - Multiple Cylinder Misfire. ? P000A - Bank 1 Camshaft 1 Position Slow Response. ? P000B - Bank 1 Camshaft 2 Position Slow Response.
SB-18-014-15REVA
2015 DODGE JOURNEY: MALFUNCTION INDICATOR LAMP ILLUMINATION. POWERTRAIN CONTROL MODULE MUST BE UPDATED WITH LATEST SOFTWARE *CN
23-035-15
Sunroof Leak Under High Water Pressure This bulletin involves installing a new sunroof service trough. The customer may describe a water leak at the rear of the sunroof when using a high pressure touchless car wash.
08-033-15 REV-A
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank(Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only)(Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after
SB-08-033-15REVA
CERTAIN VEHICLES ARE EXPERIENCING SCREEN LOCK UP ON NAVIGATION OR DISPLAY BLANK, RADIO WILL RESET, INTERMITTENTLY, NOT ABLE TO DIAL PHONE FROM RADIO BUT CAN DIAL PHONE, TRANSLATION FOR ASIAN LANGUAGE ADDED, AFTER DISCONNECTION PHONE, FAILS TO CONNECT PHONE, ETC. MODEL 2013-14 CHARGER, CHRYSLER 300, JOURNEY. *PE
08-032-15 REV-A
RE9 Radio Software Enhancements This bulletin involves updating the radio and navigation software, if required. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank (Software has been updated to better address this condition). ? Incorrect symbols displayed when entering destination using QWERTY keyboard (Software has been updated to better address this condition). ? Navigation feature lockout disable. ? Navigation system resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Add China phone book search. ? Some functionality changes for China- keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after it has been disconnect. ? Teleprompter screen shows incomplete text. ? Some functionality for traffic & weather jump button. ? After changing a language and then selecting CDDA
08-051-15
Passive Entry For Liftgate Inoperative This Bulletin involves reconfiguring the passive entry system. The customer may notice rear liftgate does not automatically lock/unlock when the liftgate switch is pressed and the key is within the proximity.
13-001-15A
Right fron side rail inner panel stamping deformity.
1300115A
Right fron side rail inner panel stamping deformity.
13-001-15
Right Front Side Rail Inner Panel Stamping Deformity This bulletin involves inspecting the right front side rail inner panel for deformities created during the stamping process. The right front side rail inner panel may have visible deformities created during the stamping process. Very few vehicles are expected to have the deformity.
18-028-15
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The purpose of this calibration is to release a required V-1 software update that meets Euro IV Emissions for the China specific test weight class.
08-032-15
RE9 Radio Software Enhancements This bulletin involves updating the radio and navigation software, if required. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank. ? Incorrect symbols displayed when entering destination using QWERTY keyboard. ? Navigation feature lockout disable. ? Navigation system resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Add China phone book search. ? Some functionality changes for China- keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after it has been disconnect. ? Teleprompter screen shows incomplete text. ? Some functionality for traffic & weather jump button. ? After changing a language and then selecting CDDA ?of? is displayed as a tracking number. ? In ?Set Date Year? only 3 digits are displayed. ? Split map view will
08-033-15
Flash: RE2 RE3 RE4 RE6 RE7 RB4 RB5 RB6 RB4 Radio Enhancements This bulletin involves updating the radio control head software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Improve AM/FM radio reception. (This only applies to 2013 or 2014 vehicles with RE6, RB6 radios located in Dubai). ? Intermittently the radio may reset. ? Radio display screen shows ?Test Mode?. ? Navigation screen locks up or display will be blank. ? Navigation feature lockout disable (International Only). ? Navigation system resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after it has been disconnect. ? Teleprompter screen shows incomplete text. ? Some functionality for traffic & weather jump button. ? After ch
08-024-15
Flash: Service Tire Pressure System Message This bulletin involves updating the Tire Pressure Module (TPM) software and performing a Misc-function routine. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): ? C151D - Tire Pressure Sensor Location Undetermined. ? C1581 - Front/Rear Side Tire Pressure Sensor Location Undetermined.
08-018-15
Flash: Intrusion Transceiver Module Enhancements This bulletin involves updating the Intrusion Transceiver Module (ITM) with new software. ITM may lose the ability to store trigger history.
08-017-15
No Travel Link Data Displayed And Other System Enhancements This bulletin involves updating the radio?s software if needed.
0801715
No Travel Link Data Displayed And Other System Enhancements This bulletin involves updating the radio?s software if needed.
18-014-15
Flash: 3.6L Or 2.4L Diagnostic and System Improvements This bulletin involves updating the Powertrain Control Module (PCM) software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2.4L Engine ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. ? U0140 - Lost Communication With Body Control Module. ? Improve alternator control at Idle. 3.6L Engine ? U0140 - Lost Communication With Body Control Module. ? P0300 - Multiple Cylinder Misfire. ? P000A - Bank 1 Camshaft 1 Position Slow Response. ? P000B - Bank 1 Camshaft 2 Position Slow Response.
1801415
Flash: 3.6L Or 2.4L Diagnostic and System Improvements This bulletin involves updating the Powertrain Control Module (PCM) software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2.4L Engine ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. ? U0140 - Lost Communication With Body Control Module. ? Improve alternator control at Idle. 3.6L Engine ? U0140 - Lost Communication With Body Control Module. ? P0300 - Multiple Cylinder Misfire. ? P000A - Bank 1 Camshaft 1 Position Slow Response. ? P000B - Bank 1 Camshaft 2 Position Slow Response.
18-059-14
Flash: Improved High Altitude Performance This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The customer may complain of less then desired engine performance at high altitude.
1805914
Improved High Altitude Performance
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.