Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
23-021-26
Broken Exterior Driver And/Or Passenger Door Handles XB2 Warranty Extension Customers may comment the following: ● One or both exterior door handles are broken. This bulletin involves replacing one or both exterior door handles.
31-001-25 REV. B
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25 REV. A
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
31-001-25
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
31-001-24
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
3100123
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
31-002-22
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
9004505
Lithium Ion Batteries Beginning April 1, 2022, a $5,000 penalty will be assessed to dealers who return any visually damaged battery to the supplier. Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process. To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp
08-177-21
BEV/Hybrid - Showroom and Display Vehicle Battery Maintenance This information only bulletin discusses procedures that must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
31-002-20
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
3100220
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
S2008000118
HVAC Control Panel Illumination Inoperative
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
9003791
1.4L FIRE Service Engine (Normally Aspirated) This engine in this kit will contain one of 8 different production full dress engines, but labeled as component engine 68275870AA or 71AA. The received engine will be configured for use with an automatic transmission, (includes auto transmission adapter plate / flexplate) or manual transmission. (includes flywheel / clutch asm) The received engine will be configured with or without a block heater. If required, dealer to purchase/install the block heater. The included instruction sheet K6855863AB in engine kit 68275870AA is to be followed for all applications that it applies. Please see the sheet for details. In addition to the items detailed in instruction sheet K6855863AB, please read the following below to determine the rework required to install this engine into a 2012- 2018 Fiat 500 (FF) with 1.4L EAB normally aspirated engine: 1) determine which condition exists for the received service engine a) vehicle has a manual transmission, received manual transmission engine. b) vehicle has a manual transmission, received automatic transmission engine. c) vehicle has an automatic transmission, received automatic transmission engine. d) vehicle has an automatic transmission, received manual transmission engine. 2) follow below steps based on condition (a) through (d) above. Condition a) No further rework required, other than ordering/installing a block heater if required. Condition b) Remove flexplate / auto trans adapter plate / auto trans engine mounting bracket / auto trans engine oil dipstick from new service engine. Transfer flywheel / clutch / manual trans engine mounting bracket / manual trans engine oil dipstick from old engine. Order/install block heater if required. Condition c) Identify the automatic transmission adapter plate on the original engine. Looking at the rear of the vehicle engine with adapter plate mounted:
9003355
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.
0808217
Auxiliary Fuel Tank, Low Fuel Indicator Will Not Turn On This bulletin involves performing a ?Restore Vehicle Configuration? and ?Proxi Alignment?. Customers may notice when the auxiliary fuel tank is empty, the auxiliary low fuel indication doesn't turn on, seeFig. 1.Low Fuel Indicators1 - Auxiliary Tank Low Fuel Indicator2 - Main Tank Low Fuel Indicator
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
22-004-16
Wheel Clicking Sound When Moving Slow This bulletin involves replacing the inserts attached to the wheel The customer may describe a clicking sound from the wheel?s plastic trim inserts when moving slowly or when stopped. The issue is heard on sunny days when the sun heats up the wheels and plastic inserts.
68105583A
Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
68141352A
3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
08-045-16
SUBJECT: Flash: Anti Lock Brake (ABS) Module System Enhancements OVERVIEW: This bulletin involves a coordinated update of the Anti-lock Brake System (ABS) module and Regenerative Brake Controller (RBC) module software SYMPTOM/CONDITION: · U0001-00 - CAN C BUS. (Sets in ABS and RBC Module). · U1487-00 - Implausible Data Received From Regenerative Brake Controller. (Sets in ABS Module). · U1200-00 - Lost Communication with Power Inverter Module. (Sets in ABS Module).
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
08-040-16
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
0804016
This bulletin involves updating the Body Control Module (BCM) software.
S20
The Powertrain Control Module (PCM) software on about 81,000 of the above vehicles may have backup lamp illumination timing that does not meet customer expectations.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
18-003-16
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
1800316
This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest
18-010-15 REV-D
Flash: 1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? Cranks fast, as if no compression. ? P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled (2014 Vehicles only). ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream (2014 Vehicles only). ? P0141 - Oxygen Sensor 1/2 Heater Performance (2015 Vehicles only). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).
18-010-15 REV. D
Flash: 1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? Cranks fast, as if no compression. ? P1524 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled (2014 Vehicles only). ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream (2014 Vehicles only). ? P0141 - Oxygen Sensor 1/2 Heater Performance (2015 Vehicles only). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).
18-010-15 REV.A
CHRYSLER 2014-2015 FIAT 500: SERVICE BULLETIN SUPERSEDES 18-010-15 DATED FEBRUARY 23, 2014, PLEASE REMOVE FROM YOUR FILES. INFORMATION REGARDING POWER CONTROL MODULE WITH THE LATEST SOFTWARE. *LJ UPDATED 10/08/15 *CN
08-088-15
Flash: RA3 Radio Software Enhancements This bulletin involves updating the radio software. The customer may experience one or more of the following: ? Display screen may lock up during very hot temperatures. ? Rear camera unintentionally switches off and display screen turns blue. ? Radio resets. ? Radio sluggish performance. ? Bluetooth dropped connections. ? Hands free calling poor sounding. ? Navigation GPS off location. ? No GPS intermittently. ? Voice recognition poor. ? Remove SAT button (soft key) on a vehicle that is not equipped with Sirius Satellite. ? Vehicles equipped with SDARS (Satellite) and No SDARS (No Satellite) may have a fast reset condition of the radio while the navigation system is active.
18-010-15 REV-C
Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance (software has been updated to better address this DTC, for EAB engines). ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).
18-010-15 REVB
Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P1046 - Cylinder 1 Oil Supply Solenoid Valve Overcurrent. ? P1048 - Cylinder 2 Oil Supply Solenoid Valve Overcurrent. ? P104A - Cylinder 3 Oil Supply Solenoid Valve Overcurrent. ? P104C - Cylinder 4 Oil Supply Solenoid Valve Overcurrent. ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).
MDH051407
THIS TSB CONTAINS AN OWNERS LETTER. SEE DOCUMENT SEARCH BUTTON. CHRYSLER FIAT 2014-2015 RAM PROMASTER( WITHOUT CAB CHASSIS & WITH CAB CHASIS). EMISSION RECALL APPLIES TO VEHICLES EQUIPPED WITH A 3.0L DIESEL ENGINE AND EQUIPPED WITH 3.6 L GASOLINE ENGINE AND A 50 STATE EMISSION CONTROL SYSTEM &VECI LABEL *LJ
08-057-15
Flash: Cruise Misspelled In The Instrument Panel Cluster This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with updated software. The customer may notice the word ?Cruise? misspelled in the IPC.
08-004-15 REVB
FLASH: Battery Electric Vehicle, Multiple System Enhancements This bulletin involves updating the software in multiple modules, Vehicle Tracking Module (VTM), Body Control Module (BCM), On-Board Charging Module (OBCM), Power Inverter Module (PIM) and Battery Pack Control Module (BPCM) if required. The customer may experience one or more of the following: ? The vehicle does not start charging when it?s plugged into the charging station. ? Intermittently the charge indicator will show it?s charging when it?s not charging. ? Intermittently the vehicle may have reduced performance. Enhancement: ? Increase of vehicle range in very cold weather. ? Improve Air Conditioning operation. ? Improvements to help reduce 12 volt battery drain when charging the vehicle with incompatible charging station. ? Improvements to DTC diagnostics. ? Enhancements to the central door lock feature. ? Improvements to locate the vehicle, using the smartphone app. ? Increase cabin preconditioning time from 2 to 10 minutes. ? Update information that is displayed by the cluster. ? Enhancements to the high voltage charging system. ? Improves the accuracy of the vehicle estimated range. ? Improve the total Lifetime energy consumed information that is display on a smartphone app. False Malfunction Indicator Lamp (MIL) illumination: ? U1014-00-Internal CAN Communication. ? P1E25-00-Hybrid/Ev Battery Failure Level 2. ? P0AA4-00-Hybrid Battery Negative Contactor Circuit Stuck Closed. ? P0AA6-00-Hybrid Battery Voltage System Isolation Fault.
08-004-15 REVA
FLASH: Battery Electric Vehicle, Multiple System Enhancements This bulletin involves updating the software in multiple modules, Vehicle Tracking Module (VTM), Body Control Module (BCM), On-Board Charging Module (OBCM), Power Inverter Module (PIM) and Battery Pack Control Module (BPCM) if required. The customer may experience one or more of the following: ? The vehicle does not start charging when it?s plugged into the charging station. ? Intermittently the charge indicator will show it?s charging when it?s not charging. ? Intermittently the vehicle may have reduced performance. Enhancement: ? Increase of vehicle range in very cold weather. ? Improve Air Conditioning operation. ? Improvements to help reduce 12 volt battery drain when charging the vehicle with incompatible charging station. ? Improvements to DTC diagnostics. ? Enhancements to the central door lock feature. ? Improvements to locate the vehicle, using the smartphone app. ? Increase cabin preconditioning time from 2 to 10 minutes. ? Update information that is displayed by the cluster. ? Enhancements to the high voltage charging system. ? Improves the accuracy of the vehicle estimated range. ? Improve the total Lifetime energy consumed information that is display on a smartphone app. False Malfunction Indicator Lamp (MIL) illumination: ? P1E25-00-Hybrid/Ev Battery Failure Level 2. ? P0AA4-00-Hybrid Battery Negative Contactor Circuit Stuck Closed. ? P0AA6-00-Hybrid Battery Voltage System Isolation Fault.
18-010-15 REVA
Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only). ? Improved cold weather starting, below -4 °F (-20 °C).
19-002-15
Clunking Noise From The Steering Column While Turning The Steering Wheel This bulletin involves replacing the steering intermediate shaft. Clunking, popping, knocking noise from the lower steering column while turning the steering wheel.
08-012-15
Intermittent Battery Drain This bulletin involves reprogramming the Body Control Module (BCM) with updated software. A small number of customers may experience a battery drain after the vehicle sits for a long period of time.
0801215
Intermittent Battery Drain This bulletin involves reprogramming the Body Control Module (BCM) with updated software. A small number of customers may experience a battery drain after the vehicle sits for a long period of time.
18-010-15
Flash:1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Codes (DTCs): ? P0141 Oxygen Sensor 1/2 Heater Performance. ? P061A Internal Control Module Torque Performance (2014 Vehicles only). ? Improved reverse lamp activation time (2015 auto trans only).
08-004-15
FLASH: Battery Electric Vehicle, Multiple System Enhancements This bulletin involves updating the software in multiple modules, Vehicle Tracking Module (VTM), Body Control Module (BCM), On-Board Charging Module (OBCM), Power Inverter Module (PIM), Battery Pack Control Module (BPCM) and Electric Vehicle Control Unit (EVCU) if required. The customer may experience one or more of the following: ? The vehicle does not start charging when it?s plugged into the charging station. ? Intermittently the charge indicator will show it?s charging when it?s not charging. ? Intermittently the vehicle may have reduced performance. Enhancement: ? Charging system enhancement during very cold weather. ? Increase of vehicle range in very cold weather. ? Improve Air Conditioning operation. ? Improvements to help reduce 12 volt battery drain when charging the vehicle with incompatible charging station. ? Improvements to DTC diagnostics. ? Enhancements to the central door lock feature. ? Improvements to locate the vehicle, using the smartphone app. ? Increase cabin preconditioning time from 2 to 10 minutes. ? Update information that is displayed by the cluster. ? Enhancements to the high voltage charging system. ? Improves the accuracy of the vehicle estimated range. ? Improve the total Lifetime energy consumed information that is display on a smartphone app. False Malfunction Indicator Lamp (MIL) illumination: ? P1E25-00-Hybrid/Ev Battery Failure Level 2. ? P0AA4-00-Hybrid Battery Negative Contactor Circuit Stuck Closed. ? P0AA6-00-Hybrid Battery Voltage System Isolation Fault.
18-069-14
Flash: MIL Illumination, P0141 Oxygen Sensor 1/2 Heater Performance, P061A Internal Control Module Torque Performance This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest software. The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0141 Oxygen Sensor 1/2 Heater Performance and/or P061A Internal Control Module Torque Performance.
1806914
Powertrain Control Module (PCM)
9003178
Clockspring/ Steering Column Module.
08-101-14
Convergence Telematics Module (CTM) Software Enhancements This bulletin involves inspecting and if required, replacement of the (CTM). The customer may notice that the displays on the TomTom screen may be missing some Battery Electric Vehicle (BEV) features. Charging schedule screen, power flow screen and charging station icon may be missing.
08-048-14REV.B
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
02-006-14
Front Suspension Clunk Noise While Making Left And Right Turns This bulletin involves replacing the front strut jounce bumpers. Clunk noise coming from the front suspension. Noise may be more noticeable during cold temperatures below 40°F (4°C). Noise may be eliminated with warmer temperatures.
0200614
Front Suspension Clunk Noise While Making Left And Right Turns This bulletin involves replacing the front strut jounce bumpers. Clunk noise coming from the front suspension. Noise may be more noticeable during cold temperatures below 40°F (4°C). Noise may be eliminated with warmer temperatures.
23-025-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-048-14
Flash: Powertrain System Improvements For Generic Scan Tool Support This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. The following Powertrain system improvement/enhancement is being released to improve the accuracy of Mode 6 data parameters in generic scan tools.
08-070-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-057-14 REV. A
Removal Of Beats Audio System This bulletin involves replacing the A-pillar trim panels, cargo covers, and amplifier.
08-057-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-057-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
17-001-14
Rear Axle Alignment Shims This bulletin is to inform service personnel of the availability of rear axle alignment shims.
08-052-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-051-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-048-14REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
9003081
Dielectric Grease This product is no longer approved for use on ignition coil and spark plug boots. Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.
08-031-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-017-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-020-14
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-031-14A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-044-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SB-18-033-13-A
FIAT: A DIAGNOSTIC TROUBLE CODE WAS SET, P113D-O2 SENSOR 1/1 SLOW RESPONSE, ON SOME VEHICLES EXPERIENCING MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION, INVOLVING FLASHING POWERTRAIN CONTROL MODULE (PCM). MODEL 2014 500L. *PE
SB-21-008-13
FIAT: INFORMATION BEING PROVIDED REGARDING THE TRANSMISSION CONTROL MODULE (TCM) INVOLVING THE MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION FLASHING. MODEL 2014 500L. *PE
18-033-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-055-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
18-030-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
D-13-29
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
08-044-13
Navigation Map Activation RA3 Radio This bulletin involves activating the navigation system on the RA3 radio prior to sale of the vehicle.
0804413
Navigation Map Activation RA3 Radio This bulletin involves activating the navigation system on the RA3 radio prior to sale of the vehicle.
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
08-002-13REV.A
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.