Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
09-010-25
2.4L Excessive Oil Consumption XS1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
U90 - Parts Ordering
U90 - Parts Ordering
09-018-24
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ● Oil pressure low indicator lamp illumination between oil changes. ● Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
100096
U90 Parts Ordering
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
1000123
Air Bag Warning Lamp Illumination Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
S2325000007
MIL/check engine lamp comes on after performing U90 recall PCM software update.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
RecallU90
Emissions Recall U90 - Catalyst Efficiency
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
0900323
2.4L Excessive Oil Consumption XB1 Warranty Extension The customer may describe one or more of the following: ? Oil pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.
88806
Warranty Bulletin D-23-01 - (XB1) 2.4L Engine ? Select 2014 - 2019 Jeep Cherokee (KL), 2017 - 2018 Jeep Compass (MP), 2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)
U90 Combo Rev5
Emission Recall U90 Catalyst Efficiency
09-013-22
2.4L Engine Oil Consumption Test The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.
Recall U90
Emission Recall U90 Catalyst Efficiency
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
18-042-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure. P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(2016 BU EMEA only). Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle (EMEA and APAC only). The following enhancements are also included: Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
1804221
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure. P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(2016 BU EMEA only). Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. A ticking noise coming from the top of the engine area. The ticking noise is heard particularly at idle (EMEA and APAC only). The following enhancements are also included: Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
08-027-21
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
0802721
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.
W80 Combo Phase2
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
W80A
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 2)
09-002-21
2.0L or 2.4L Engine Replacement This bulletin involves replacing the long block due to a crankshaft imbalance condition. These vehicles may exhibit a vibration in the engine.
0900221
2.0L or 2.4L Engine Replacement This bulletin involves replacing the long block due to a crankshaft imbalance condition. These vehicles may exhibit a vibration in the engine.
W80
Customer Satisfaction Notification W80 Oil Consumption Inspection (Revision 1)
S2108000027
CEL, Check Engine Lamp On, DTC P0339 Crankshaft Position Sensor Intermittent
W80 Combo Phase1
Customer Satisfaction Notification W80 Oil Consumption Inspection
S1508000374
Keys/Fobiks, Programming Keys With High Line BCM (L3 BCM)
09-006-20 REV. B
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
0900620
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
S2008000093
Blind Spot Or Park Assist Warnings, False Activation
09-006-20 REV. A
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
09-006-20
2.4L Engine Oil Consumption Test This bulletin involves performing an oil consumption verification test. The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
09-004-20
No Weep Hole In Muffler Assembly This bulletin involves drilling a weep hole in the muffler assembly. The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.
08-027-20
2.4L Ignition Coil Boot Replacement This bulletin involves replacing all four ignition coil insulating boots. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.
S2008000013
Key Programming, Security Pin Request, Pin Invalid
9004022
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
31-003-19
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31-006-19
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
V54 REV1
Revised Customer Satisfaction Notification V54 Engine Cooling Fan
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
08-110-17
Flash: Drivetrain Control Module (DTCM) Diagnostic and System Improvements This bulletin involves reprogramming the DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure.
1808917
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs have been set:P1523-00 - VVA Low Oil Pressure. P1524-00 - Oil Pressure Out Of Range - Camshaft Advance/Retard Disabled. P1D7F-00 - ETC Self-Learning Failure. P0141 - O2 Sensor 1/2 Heater Performance. Some customers may experience one or more of the following conditions:Cruise control will not set at 32 kph (20 mph). Engine cranking times out after five seconds. Cruise control will not engage at highway speeds and when in 6th gear. The following enhancements are also included:Improved purge sensor performance. Updated fuel strategy to inhibit spark plug fouling.
0810217
RA2 RJ2 RG2 RL2 and RM2 Radio Enhancements This bulletin involves updating the radio with the latest available software. The customer may notice one of the following:The parking sensor (warning chime) is still audible after the key is in the off position(EMEA and APAC Only). The radio re-boots if more than five favorite presets are set for each category (i.e. Sport or Rock)(RA2 Sales Code Only). Emergency number (i.e. 911) not set as default(U.S. BU Vehicles Only). Radio re-boots or displays black screens. When receiving or making outgoing phone calls, the other person may hear an echo or repeated phrases(16 MY FB Only). A false message displayed in the Instrument Panel Cluster (IPC) such as ?Parking Sensors Unavailable? and/or ?Sound System Unavailable?(16 MY FB Only).
21-042-17
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0887 - TCM Power Control Circuit High. P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Fourth Gear. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance(2015 BU Only). P1CC9 - Unable to Engage Gear(2015 BU Only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective(2015 BU Only). U0401 - Implausible Data Received From ECM-PCM(2015 BU Only). In addition, customers may notice the following condition(s):Harsh 1-2 upshift. Harsh garage shifts (Park to Reverse or Drive). CAN bus message may drop out after a network restart.
9003357
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
9003413
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
9003109
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
9003696
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
9003694
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
9003687
Restraints Remove I-Sheet from packaging. Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
9003681
Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.
08-086-16
Flash: Engine Does Not Start at The First Attempt This bulletin involves upgrading the software in the Electronic Steering Lock (ESL) Module. The customer may experience malfunction on first attempt to start the vehicle. Initial cranking is inhibited but should start/crank on the second attempt. Upon further inspection the technician may find Diagnostic Trouble Code (DTC) B1000-01 - Electronic Control Unit - General Electrical Failure stored in the ESL Module.
21-035-16
Transmission Shift And Drivability Enhancements For P0901-00. This bulletin involves performing transmission harness replacement per S55 recall.Both the PCM and TCM must be up to date for these changes to be effective after the transmission harness repair. Customers may experience a Malfunction Indicator Lamp (MIL) illumination after S55 recall TCM flash has been performed. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0901-00 - Clutch 1 Actuator Control Circuit Range Performance.
2103216
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience the vehicle doesn?t pass back into drive mode when choosing to change gears using the paddle shifters. Even when holding the (+) paddle, while the gear lever is still in Drive, the vehicle remains locked in that mode.The following improvements are included in this update: Paddle shifter enhancements are included in this software update.
2103116
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the TCM memory: P061B - Internal Control Module Torque Calculation Performance. P072F - Stuck In Gear 4. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance (2015 BU only). P0887 - TCM Power Control Circuit High (2015 BU only). P1CC9 - Unable to Engage Gear (2015 BU only). P1D98 - Incorrect Gear Ratio Clutch B or D Defective (2015 BU only). U0401 - Implausible Data Received From ECM-PCM (2015 BU only).In addition, customers may experience the following conditions: CAN Bus message may drop out after a network restart. Harsh 1-2 Upshift. Harsh Garage Shifts (Park to Reverse or Drive).
2401216
Water Leak On Right Front Floorboard This bulletin involves securing the condensation drain tube to the HVAC housing. Customers may experience a water leak on the right front floorboard inside the vehicle while using the climate controls or Heating Ventilation Air Conditioning (HVAC).
1000316
Rear Outboard Seat Belt Is Slow To Retract This bulletin involves installing a washer between the seat belt retractor mounting bolt and the retractor on both the rear outboard side retractors. The customer may describe that either one or both of the rear outboard seat belts may retract slowly.
05152029
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
08-010-16 REV. D
Flash: Diagnostic And System ImprovementsThis bulletin involves updating the Body Control Module (BCM), Powertrain Control Module (PCM) and Transmission Control Module (TCM) with the latest available software. All three modules must be up to date when finished with this service action. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):· **P1066 - Cylinder 1 oil supply solenoid valve switch off time out of range.· P1068 - Cylinder 2 oil supply solenoid valve switch off time out of range. · P106A - Cylinder 3 oil supply solenoid valve switch off time out of range. · U1424-00 - Implausible Engine Torque Signal Received.** · P0335 - Crankshaft Position Sensor Circuit. P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle.· P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard.· P1CED - VAriable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance.· P1607 - PCM Internal Shutdown Timer Rationality.· P2610 - PCM Internal Engine Off Timer Performance.· P0440 - General EVAP System Failure.· P0441 - EVAP Purge System Performance.· P0456 - EVAP System Small Leak.· P0455 - EVAP System Large Leak.· P0452 - EVAP Pressure Switch Stuck Closed· P0133 - O2 Sensor 1/1 Slow Response.· C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · P1185 - General Pressure Sensor Correlation. · C0061 - Lateral Acceleration Sensor. · P0128 - Thermostat Rationality. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Ration
21-013-16 REV. B
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
68321236A
RF Hub Module DTC, U1765-87 "RFHM (Radio Frequency Hub Module) - Missing Message" may appear in a stored state on a ignition power cycle. No troubleshooting or parts replacement is necessary if this code is stored as the system is functioning to design.
68321236A$
RF Hub Module DTC, U1765-87 "RFHM (Radio Frequency Hub Module) - Missing Message" may appear in a stored state on a ignition power cycle. No troubleshooting or parts replacement is necessary if this code is stored as the system is functioning to design.
08-010-16 REV. C
Flash: Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM), Powertrain Control Module (PCM) and Transmission Control Module (TCM) with the latest available software. All three modules must be updated in this service action. Powertrain Control Module (PCM) Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U1424-00 - Implausible Engine Torque Signal Received. P0335 - Crankshaft Position Sensor Circuit. P1185 - General Pressure Sensor Correlation. P050D - Cold Start Rough Idle. P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. P1CED - VAriable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. P1607 - PCM Internal Shutdown Timer Rationality. P2610 - PCM Internal Engine Off Timer Performance. · P0440 - General EVAP System Failure. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P0455 - EVAP System Large Leak. · P0452 - EVAP Pressure Switch Stuck Closed. · P0133 - O2 Sensor 1/1 Slow Response. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · P1185 - General Pressure Sensor Correlation. · C0061 - Lateral Acceleration Sensor. · P0128 - Thermostat Rationality. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · C0062 - Longitudinal Acceleration Sensor In Airbag System - Signal Invalid. · U0402 - Implausible Data Received From TCM - (Transmission Control Module).
0801016
Flash: Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM), Powertrain Control Module (PCM) and Transmission Control Module (TCM) with the latest available software. All three modules must be updated in this service action. Powertrain Control Module (PCM) Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · U1424-00 - Implausible Engine Torque Signal Received. · P0335 - Crankshaft Position Sensor Circuit. · P1185 - General Pressure Sensor Correlation. · P050D - Cold Start Rough Idle. · P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. · P1CED - VAriable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. · P1607 - PCM Internal Shutdown Timer Rationality. · P2610 - PCM Internal Engine Off Timer Performance. · P0440 - General EVAP System Failure. · P0441 - EVAP Purge System Performance. · P0456 - EVAP System Small Leak. · P0455 - EVAP System Large Leak. · P0452 - EVAP Pressure Switch Stuck Closed. · P0133 - O2 Sensor 1/1 Slow Response. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · U0428-00 - Implausible Data Received From Steering Angle Sensor Module. · P1185 - General Pressure Sensor Correlation. · C0061 - Lateral Acceleration Sensor. · P0128 - Thermostat Rationality. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. · C0062 - Longitudinal Acceleration Sensor In Airbag System - Signal Invalid.
68256494A$
Windshield Please contact Chuck Hood at cell (248) 613-7591 regarding BU & FB windshields that exhibit imperfections such as stress cracking, inclusions/bubbles, scratches, or distortions. If no response in 15 minutes, proceed with repair.
R73
Customer Satisfaction Notification R73 Wheel Stud Wrench The wheel stud wrench on about 11,700 of the above vehicles may break during use due to a non-compliant heat treatment process causing the material hardness to be out of specification. The wheel stud wrench must be replaced on the affected vehicles.
06106092A
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
06106092A$
Seat Relay For a Jeep Renegade or Fiat 500X ONLY, if the driver's power seat will not move in any axis and the key is in the on position with the door open: 1. Please take a Vehicle Scan Report, taking note of any active or stored DTC's, especially in the Body Control Module (BCM). 2. Before replacing the relay, call Rick Gordon at cell (248) 630-6281. If no answer leave a message and if after 15 minutes, there is no return call, proceed with the repair. 3. In the event there is no call-back, please email the Vehicle Scan Report to rick.gordon@fcagroup.com
08-033-16 REV. C
RA4 RG4 RJ4 Radio Enhancements This bulletin involves updating the radio software. Customers may experience one or more of the following: · **Uconnect Apps are missing (16 MY BU, RRT portion, US market only). · Unable to register Uconnect (16 MY BU, RRT portion, US market only). · Assist button on App is missing (16 MY BU, RRT portion, US market only).** · Character missing on the keyboard with Cyrillic alphabet (For EU Market only). · Time of arrival NAV settings not saved over key-cycle (For EU Market only). · Audio Off delayed when pressing On/Off button (For EU Market only). · Digital Audio Broadcast (DAB) button missing after system startup (For EU Market only). · Head unit turns on at USB disconnection (For EU Market only). · Poor quality of German translations. · Acoustic warning missing when approaching a speed camera (EMEA market only). · 3D view malfunctions. · Road signs not correctly viewed during navigation. · After ignition has been turned on the language switches automatically to Italian from previously selected language. · Forward Collision Warning With Mitigation (FCW+) turns off spontaneously, after the ignition has been turned on and FCW+ warning light is on.
68249986A$
MY16 RA3 & RA4 Replacement Radios All MY16 RA3 and RA4 replacement radios must be ordered through the exchange process at United Radio. DO NOT order a NEW radio from Mopar. Go back and order a "Z" level part number. (example: Z8249986A$) The MY16 replacement radios must be reconfigured by United Radio to the wireless network provider in order for Uconnect Apps to work properly.
68232614A$
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
08-033-16 REV. B
RA4 RG4 RJ4 RADIO ENHANCEMENTS THIS BULLETIN INVOLVES UPDATING THE RADIO SOFTWARE. CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING: · **CHARACTER MISSING ON THE KEYBOARD WITH CYRILLIC ALPHABET (FOR EU MARKET ONLY). · TIME OF ARRIVAL NAV SETTINGS NOT SAVED OVER KEY-CYCLE (FOR EU MARKET ONLY). · AUDIO OFF DELAYED WHEN PRESSING ON/OFF BUTTON (FOR EU MARKET ONLY). · DIGITAL AUDIO BROADCAST (DAB) BUTTON MISSING AFTER SYSTEM STARTUP (FOR EU MARKET ONLY). · HEAD UNIT TURNS ON AT USB DISCONNECTION (FOR EU MARKET ONLY).** · POOR QUALITY OF GERMAN TRANSLATIONS. · ACOUSTIC WARNING MISSING WHEN APPROACHING A SPEED CAMERA (EMEA MARKET ONLY). · 3D VIEW MALFUNCTIONS. · ROAD SIGNS NOT CORRECTLY VIEWED DURING NAVIGATION. · AFTER IGNITION HAS BEEN TURNED ON THE LANGUAGE SWITCHES AUTOMATICALLY TO ITALIAN FROM PREVIOUSLY SELECTED LANGUAGE. · FORWARD COLLISION WARNING WITH MITIGATION (FCW+) TURNS OFF SPONTANEOUSLY, AFTER THE IGNITION HAS BEEN TURNED ON AND FCW+ WARNING LIGHT IS ON.
68066351A
Keyfob 2016 Vehicle Keyfobs with Passive Entry Keyless Go Feature - Engineering is investigating a keyfob unable to program or no function or low keyfob coin battery condition.~ Prior to replacing keyfob on MY16 vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.
09-008-16
2.0L Or 2.4L Engine Replacement This bulletin involves replacing the long block due to a crankshaft imbalance condition. These vehicles may exhibit a vibration in the engine.
08-010-16 REV. B
Flash: Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM), Powertrain Control Module (PCM) and Transmission Control Module (TCM) with the latest available software. All three modules must be updated in this service action. Powertrain Control Module (PCM) Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ·**U1424-00 - Implausible Engine Torque Signal Received. ·P0335 - Crankshaft Position Sensor Circuit. ·P1185 - General Pressure Sensor Correlation. ·P050D - Cold Start Rough Idle. ·P1CEC - Variable Valve Solenoid Valve Cold Start Closing Position 1 Timing Over-Retard. ·P1CED - VAriable Valve Timing Solenoid Valve Cold Start Closing Position Timing Over-Advance. ·P1607 - PCM Internal Shutdown Timer Rationality. ·P2610 - PCM Internal Engine Off Timer Performance. ·P0440 - General EVAP System Failure. ·P0441 - EVAP Purge System Performance. ·P0456 - EVAP System Small Leak. ·P0455 - EVAP System Large Leak. ·P0452 - EVAP Pressure Switch Stuck Closed. ·P0133 - O2 Sensor 1/1 Slow Response. ·C0501 - Wheel Speed Signal Left Front Rationality. ·C0507 - Wheel Speed Signal Right Front Rationality. ·C050D - Wheel Speed Signal Left Rear Rationality. ·C0513 - Wheel Speed Signal Right Rear Rationality. ·U0428-00 - Implausible Data Received From Steering Angle Sensor Module. ·P1185 - General Pressure Sensor Correlation. ·C0061 - Lateral Acceleration Sensor. ·P0128 - Thermostat Rationality. ·C0501 - Wheel Speed Signal Left Front Rationality. ·C0507 - Wheel Speed Signal Right Front Rationality. ·C050D - Wheel Speed Signal Left Rear Rationality. ·C0513 - Wheel Speed Signal Right Rear Rationality. ·C0062 - Longitudinal Acceleration Sensor In Airbag System - Signal Invalid.** ·U0402 - Implausible Data Received From TCM - (Transmission Control Module).
22-004-16
Wheel Clicking Sound When Moving Slow This bulletin involves replacing the inserts attached to the wheel. The customer may describe a clicking sound from the wheels plastic trim inserts when moving slowly or when stopped. The issue is heard on sunny days when the sun heats up the wheels and plastic inserts.
05064358A
Speakers: For 2016 speakers issues (all bodies), before replacing this part please contact one of the following people regarding this repair: Mahmoud (Mo) Touha at cell (248) 705-3934. If no response is received within 15 minutes, then please proceed with repair.~
RL305553A
9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
08-063-16
RA2 Radio software enhancement.
0806316
RA2 Radio software enhancement.
08-033-16A
Updating the radio software.
0803316A
Updating the radio software.
08-061-16
Wire repairs to engine harness.
0806116
Wire repairs to engine harness.
Z5091195A
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Z5091195A$
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
08-057-16
RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · Navigation failed message is displayed. · Clock not automatically updating to local time. · Poor or no connection to cellular network. · HVAC temperature out of sync with radio display (KL vehicles). · Display goes blank/black. · Radio locks up. · Some Uconnect App remote commands do not execute with the vehicle.
68277402A
Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
23-013-16
Pod Switch Buttons Sticking On Center Instrument Panel Bezel This bulletin involves the replacement of the right instrument panel bezel. If a customer?s VIN is listed in VIP or your RRT VIN list, perform the repair. For all other customers that describe the symptom/condition listed above, perform the Repair Procedure.
08-036-16
Flash: Amplifier Audio Enhancement This bulletin involves updating the amplifier (AMP) software. The customer may notice a poor audio quality. This condition may happen when the audio volume is at a mid to high output.
0803616
This bulletin involves updating the amplifier (AMP) software.
08-033-16
RA4 RG4 Radio Enhancements This bulletin involves updating the radios software. Customers may experience one or more of the following: · Poor quality of German translations. · Acoustic warning missing when approaching a speed camera. (EMEA market only) · 3D view malfunctions. · Road signs not correctly viewed during navigation. · After ignition has been turned on the language switches automatically to Italian from previously selected language. · Forward Collision Warning with mitigation (FCW+) turns off spontaneously
08-034-16
RL4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · ParkSense audio delay. · Forward Collision Warning (FCW) turns off spontaneously after key on and FCW warning light is on.
0803316
This bulletin involves updating the radios software.
21-013-16
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
21-013-16 REV. A
948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic.
2101316 REV A
Speed Transmission Quick Learn Procedure.
2101316REVA
Speed Transmission Quick Learn Procedure.
2101316
Speed Transmission Quick Learn Procedure.
05-001-16 REV. A
Flash: ABS Module Electronic Parking Brake Enhancements This bulletin involves updating the Anti-lock Brake System (ABS) module software. The customer may describe: · The key may get stuck in the ignition key cylinder. · The Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected. NOTE: The Parking Brake will apply when the switch is manually activated.
0500116 REV A
: ABS Module Electronic Parking Brake Enhancements.
0500116REVA
: ABS Module Electronic Parking Brake Enhancements.
1801316REVA
Diagnostic And System Improvements.
18-013-16
Flash: 1.4L Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience one or more of the following conditions: · Cruise control will not allow resume at 32 kph (20 mph). · Engine cranking times out after 5 seconds. · Cruise control is disengaging at highway speeds when upshifting to 6th gear.
1801316
Diagnostic And System Improvements.
0801416
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
08-013-16
Flash: Instrument Panel Cluster (IPC) Enhancement This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software. The customer may notice that the IPC brightness level may not adjust correctly to correspond with the outside light levels. The following enhancements are included in the software update: · With this software update there is a new message added to the IPC. The message appears when the lever is in ?P? position and the brake pedal is pressed. · Enhancement was made to properly calculate and display when the next service maintenance is needed.
0801316
This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
08-010-16
Flash: Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM), Powertrain Control Module (PCM), Transmission Control Module (TCM) with the latest available software. All three modules must be updated in this service action. Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): · P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. · P1CC9 - Unable to Engage Gear. · P1D98 - Incorrect Gear Ratio Clutch B or D Defective. · P1DAD - Input Shaft-Output Shaft Direction Correlation. · U1424 - Implausible Engine Torque Signal Received. In addition, the customer may also experience one or more of the following transmission related conditions: · Garage Shifts (Shifting from Park or Neutral into Drive or Reverse). · Harsh 1-2 upshifts. · Less than desired accelerator pedal response in Sport and Traction Plus modes. · RPM flare at engine start. · Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start. The following enhancements are included in the software update: · Vehicle performance enhancements. · Improve transmission shift enhancements for sand and snow mode. · Improved paddle shifter operation. Body Control Module (BCM) A customer may describe that the remote key is not recognized and doesn't open/close door locks. In some cases the engine may not start due to the fact that a valid key is not recognized. Upon further investigation the technician may find the Diagnostic Trouble Codes (DTCs): · B105A-64 - Doors Lock All-Signal Plausibility Failure. · B105D-64 - Doors Deadlock Or Unlock Driver-Signal Plausibility Failure.
RL108213A$
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
08-003-16 REV. A
Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the RFHM software. The customer may experience one or both of the following conditions: · Passive entry light on with diagnostic trouble code (DTC) B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. · Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality. · After an engine start and after the closure of the door, a message in the cluster is being displayed ?Key Not Detected? when the key is actually present.
0800316 REV A
This bulletin involves updating the RFHM software.
0800316REVA
This bulletin involves updating the RFHM software.
05-001-16
Flash: ABS Module Electronic Parking Brake Enhancements This bulletin involves updating the Anti-lock Brake System (ABS) module software. The customer may describe: · **The key may get stuck in the ignition key cylinder.** · The Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected.
0500116
: ABS Module Electronic Parking Brake Enhancements.
08-003-16
Flash: Radio Frequency Hub Module (RFHM) Enhancement This bulletin involves updating the RFHM software. The customer may experience one or both of the following conditions: · Passive entry light on with diagnostic trouble code (DTC) B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. · Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality. · After an engine start and after the closure of the door, a message in the cluster is being displayed ?Key Not Detected? when the key is actually present.
0800316
This bulletin involves updating the RFHM software.
08-002-16
Malfunction Indicator Lamp (MIL) Illumination Diagnostic Trouble Code (DTC) P0113 The wiring at the connector of the Intake Air Temperature (IAT) sensor may be compromised due to wire strain causing DTCs. This bulletin involves adding a jumper harness on the IAT sensor to reduce this strain. Some customers may experience a MIL illumination. Upon further inspection, the technician may find P0113 Intake Air Temperature Sensor 1 Circuit High. Installing the jumper harness will help prevent IAT issues from occurring.
24-002-16
Air Conditioning Inoperative This bulletin involves replacing the Manual Climate Control Module. A small number of customers may experience the loss of air conditioning operation (A/C compressor will not turn on).
05-012-15
Flash: ABS Module Electronic Parking Brake Enhancements. This bulletin involves updating the Anti-Lock Brake System (ABS) module software. The customer may describe the Electronic Parking Brake (EPB) does not engage with the ?Auto Apply? feature selected. NOTE: The Parking Brake will apply when the switch is manually activated.
0501215
ABS Module Electronic Parking Brake Enhancements.
08-126-15
Flash: BCM Diagnostic And System Improvements This bulletin involves updating the Body Control Module (BCM) software. A customer may describe that the remote key is not recognized and doesn't open/close door locks. In some cases the engine may not start due to the fact that a valid key is not recognized. Upon further investigation the technician may find the Diagnostic Trouble Codes (DTCs): ? B105A-64 - Doors Lock All-Signal Plausibility Failure. ? B105D-64 - Doors Deadlock Or Unlock Driver-Signal Plausibility Failure.
0812615
This bulletin involves updating the Body Control Module (BCM) software.
18-030-15 REV C
Flash: 2.4L Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? U0402 - Implausible Data Received From TCM. ? P0133 - O2 Sensor 1/1 Slow Response. ? P0171 - Fuel System 1/1 Lean. ? P050D - Cold Start Rough Idle. In addition, customers may experience one or more of the following concerns: ? Vehicle performance enhancements. ? Clatter or ticking noise from the engine at idle. ? RPM flare at cold start. ? Less than desired idle performance. ? Cold engine RPM surge with gear engagement.
21-024-15 REV D
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? U1424 - Implausible Engine Torque Signal Received. In addition, the customer may also experience one or more of the following transmission related conditions: ? Garage Shifts (Shifting from Park or Neutral into Drive or Reverse). ? Harsh 1-2 upshifts. ? Less than desired accelerator pedal response in Sport and Traction Plus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start. The following enhancements are included in the software update: ? Vehicle performance enhancements. ? Improve transmission shift enhancements for sand and snow mode. ? Improved paddle shifter operation.
2102415 REV D
Transmission Shift And Drivability Enhancements.
2102415REVD
Transmission Shift And Drivability Enhancements.
23-051-15
Liftgate Open Indicator Illuminated And Liftgate Will Not Latch Fully This bulletin involves replacing the liftgate bumpers, liftgate weatherstrip, and adjusting the liftgate latch. The customer may describe the liftgate open indicator is illuminated in the instrument cluster information center (Fig. 1) and/or the liftgate does not close fully. When the liftgate is shut, the liftgate latch engages the striker with the first latch position but does not achieve the second latch position. Fig. 1 Liftgate Open Indicator
53034160A
Part Description: Accelerator Pedal Issue Description: Vehicle has accelerator pedal fault code. Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
08-085-15 REV A
Flash: Instrument Panel Cluster (IPC) Enhancement This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest available software. The customer may notice that the IPC brightness level may not adjust correctly to correspond with the outside light levels. The following enhancements are included in the software update: ? With this software update there is a new message added to the IPC. The message appears when the lever is in ?P? position and the brake pedal is pressed. ? Enhancement was made to properly calculate and display when the next service maintenance is needed.
21-024-15 REV C
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. ? P1CC9 - Unable to Engage Gear. ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective. ? P1DAD - Input Shaft-Output Shaft Direction Correlation. ? U1424 - Implausible Engine Torque Signal Received. In addition, the customer may also experience one or more of the following transmission related conditions: ? Garage Shifts (Shifting from Park or Neutral into Drive or Reverse). ? Harsh 1-2 upshifts. ? Less than desired accelerator pedal response in Sport and TractionPlus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start. The following enhancements are included in the software update: ? Improved paddle shifter operation. ? Improve transmission shift enhancements for sand and snow mode.
2102415 REV C
Transmission Shift And Drivability Enhancements.
2102415REVC
Transmission Shift And Drivability Enhancements.
23-046-15
Liftgate Fiat Emblem Loose This bulletin involves replacing the liftgate Fiat emblem. The customer may describe the liftgate Fiat emblem is loose.
05-010-15 REV A
Front Brake Squeak/Squeal Noise This bulletin involves cleaning excessive sealant from the front brake caliper adaptor brackets and replacing the adaptor bracket mounting bolts and/or replacing the front brake pads and related hardware. The customer may describe one or more of the front brake squeak/squeal noise symptoms/conditions: - Squeak/squeal noise during moderate brake apply combined with light steering. The noise typically occurs with warm brakes after several brake applications. - Squeak/squeal noise during low speed brake apply with vehicle moving forward or reverse. The noise typically only occurs after the vehicle sits overnight in colder ambient temperatures and the noise will go away after a few brake applications.
08-059-15A
Travel Link button not displayed on the radio screen.
0805915A
Travel Link button not displayed on the radio screen.
08-059-15
Travel Link button not displayed on the radio screen.
0805915
Travel Link button not displayed on the radio screen.
2102415-1
Flash: Transmission Shift And Drivability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance ? P1CC9 - Unable to Engage Gear ? P1D98 - Incorrect Gear Ratio Clutch B or D Defective ? P1DAD - Input Shaft-Output Shaft Direction Correlation ? U1424 - Implausible Engine Torque Signal Received In addition, the customer may also experience one or more of the following transmission related conditions: ? Less than desired 1-2 upshift on tip-in acceleration. ? Less than desired accelerator pedal response in Sport and TractionPlus modes. ? RPM flare at engine start. ? Less than desired idle performance when shifting into DRIVE or REVERSE following a cold start.
D-15-13
Claim Reimbursement Guidelines - Radar Sensor Alignment Tool
9002519
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.