Vehicle report
Technical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
S1408000384 REV.J
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.I
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
21-040-25
948TE Transmission Reaction Shaft Service Bushing Kit Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance.
9100624
Verify Reman part number availability. Order the "R" part number for all orders:
S1408000384 REV.H
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.G
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384 REV.F
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S1408000384
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
1000123
Air Bag Warning Lamp Illumination Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.
9100229
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
9100226
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
93023
Warranty Bulletin D-16-03 - "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC (Rev. B)
93120
FCA Caribbean Warranty Bulletin ID-23-20 "Can / Am" Warranty Coverage - 594 / 595 / 596 WCC
9100196
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
0700723
Water Quality When Mixed With Engine Coolant
9100142
Mirror
1804823
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
3100122
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
S2209000004
If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
S2208000073
No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S1708000118
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S1708000118 RevB
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
S2108000198
Media Device Connection Guidelines For Bluetooth, Apple CarPlay, Android Auto Or USB To The Radio Head Unit
S2108000163
No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S2109000004
Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S1809000007RevC
Customer Complaint May Include Engine Oil Leak Or Consumption
9004386
WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
08-087-21
Flash: Body Control Module (BCM) Updates This bulletin involves reprogramming the BCM with the latest available software. Customers may notice the following: Message on the Instrument Panel Cluster (IPC) - Headlamp (low beam) is out but the headlamps are all functioning properly.
0808721
Flash: Body Control Module (BCM) Updates This bulletin involves reprogramming the BCM with the latest available software. Customers may notice the following: Message on the Instrument Panel Cluster (IPC) - Headlamp (low beam) is out but the headlamps are all functioning properly.
S2008000125
Low Beam Headlamp Out Message Displayed On EVIC Intermittently. DTC B162F-64 Or B1638-64
S2008000125 Rev.
Low Beam Headlamp Out Message Displayed On EVIC Intermittently. DTC B162F-64 Or B1638-64
S1708000118 Rev.
Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination After Key Off
S1608000226
Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
18-039-21
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTChas been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. The following DTCs have been changed from a one trip fault to a two trip fault: P0607 - ECU Internal Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).
1803921
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTChas been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). U0100 - Lost Communication With ECM/PCM. The following DTCs have been changed from a one trip fault to a two trip fault: P0607 - ECU Internal Performance. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).
S16080002261
Battery Tester Warranty Code Procedures, Medtronic Update Process
S1821000001
Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
S1809000007 Rev.
Customer complaint may include engine oil leak/consumption.
S2124000004
A/C does not cool and vehicle is low on Freon charge but no leak is found with sniffer or black light anywhere in the system
S2008000125RevA
Low Beam Headlamp Out Message Displayed On EVIC Intermittently. DTC B162F-64 Or B1638-64
9004293
MODULE, Body Controller, Telematics If the BCM is being replaced due to a confirmed/reported Low Beam Headlight Out message, and the headlights are functional, please refer to SOL Publication S2008000125. Per the SOL, software is being developed to address the issue and component replacement will not resolve this issue.
9003637
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S2008000010
Apple Carplay Inoperative Or Not Working, Phone Not Pairing, Carplay Lockup, Freeze or Audio Concerns
21-040-20
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
2104020
Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
S2018000008
Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
18-029-20 REV. A
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set:U0100 - Lost Communication With ECM/PCM. In addition, the customer may also experience the following: The vehicle will not crank if the ECM gets hotter than 50 °C (122°F).
23-015-20
Disinfectant Solution Recommended for COVID-19
08-049-20
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
18-039-20
Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
S2019000002
Hands On Steering Wheel Message In EVIC
18-029-20
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set:U0100 - Lost Communication With ECM/PCM. In addition, the customer may also experience the following:The vehicle will not crank if the ECM gets hotter than 50 °C (122 °F).
21-027-20
Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find oneor more of the following Diagnostic Trouble Codes (DTCs) have been set:P0780 - Gear Shift Malfunction. P1DD2-00 - Torque Request Signal From TCM Denied. Customers or technicians may experience the following:Transmission will be placed into Limp-in mode. While driving at 65 kph (40 mph) a bump will be felt and the RPM will jumpto 4000 RPM.
09-004-20
No Weep Hole In Muffler Assembly This bulletin involves drilling a weep hole in the muffler assembly. The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.
S2008000013
Key Programming, Security Pin Request, Pin Invalid
31-004-19
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31-005-19
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100319
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
3100419
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
3100519
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
3100619
Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18-089-19
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
1808919
wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9004150
SEAL, Input If looking to replace stubshaft due to ATX fluid leaking, do not replace PTU seals. None of the seals from the PTU side will need to be replaced whenever the ATX stubshaft is replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft, it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft - PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.
9003220
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.