25N17
Other
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Vehicle report
2017 FORD C-MAX
Service bulletins
114 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
SSM 54601
Service Bulletin/Repair Instructions
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
TSB 25-2570
Service Bulletin/Repair Instructions
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
SSM 54366
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
SSM 53040
Service Bulletin/Repair Instructions
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
TSB 24-2165
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
TSB 22-2396
Service Bulletin/Repair Instructions
Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
TSB 22-2309
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 50975
Service Bulletin/Repair Instructions
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
TSB 22-2230
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
SSM 50804
Service Bulletin/Repair Instructions
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
SSM 50744
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
TSB 22-2162
Service Bulletin/Repair Instructions
Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
TSB 22-2066
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 50502
Service Bulletin/Repair Instructions
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
SSM 50375
Service Bulletin/Repair Instructions
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
SSM 50257
Service Bulletin/Repair Instructions
Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50039
Service Bulletin/Repair Instructions
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2152
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
TSB 21-2033
Service Bulletin/Repair Instructions
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
SSM 49086
Service Bulletin/Repair Instructions
Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2255
Service Bulletin/Repair Instructions
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 48911
Service Bulletin/Repair Instructions
Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48908
Service Bulletin/Repair Instructions
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
SSM 48858
Service Bulletin/Repair Instructions
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
TSB 20-2171
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 48757
Service Bulletin/Repair Instructions
Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
SSM 48619
Service Bulletin/Repair Instructions
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
SSM 48598
Service Bulletin/Repair Instructions
2013-2018 C-Max, 2013-2020 Fusion Hybrid/MKZ Hybrid vehicles may exhibit a MIL with Diagnostic Trouble Code (DTC) P0340 and/or P0344. This may occur due to excessive moisture build up in the engine oil. Excess moisture occurs when the vehicle is driven short distances and/or less than 6,000 combined miles per year. To correct the condition, replace the camshaft position sensor (CMP) and change the engine oil. Advise the customer to perform more frequent oil changes and allow the internal combustion engine to reach operating temperature when running to prevent reoccurrence. Refer to the owners guide - maintenance - engine oil check - operating in cold climates and short driving cycles.
SSM 48423
Service Bulletin/Repair Instructions
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48340
Service Bulletin/Repair Instructions
Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
SSM 48130
Service Bulletin/Repair Instructions
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
SSM 48123
Service Bulletin/Repair Instructions
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
TSB 19-2207
Service Bulletin/Repair Instructions
Some 2013-2017 C-Max/Fusion/MKZ Hybrid/Energi vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1450, P0456, P0457, P04EE and/or P04EF. This may be due to the sealing capability of the canister purge valve. To correct the condition, follow the Service Procedure steps to update the PCM software and replace the canister purge valve.
SSM 48053
Service Bulletin/Repair Instructions
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
TSB19-2158
Service Bulletin/Repair Instructions
Some 2017-2019 Fusion Hybrid/Fusion Energi/MKZ Hybrid and 2017-2018 C-Max vehicles built on or before 27-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P013A stored in the powertrain control module (PCM). This may be due to downstream oxygen sensor parameters in the PCM software. To correct the condition, follow the Service Procedure to update the PCM software.
SSM 47976
Service Bulletin/Repair Instructions
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 47850
Service Bulletin/Repair Instructions
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 47875
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.
TSB 19-2065
Service Bulletin/Repair Instructions
Some 2017 Fusion Hybrid/Fusion Energi/MKZ Hybrid/C-Max and 2019 Fusion Hybrid/MKZ Hybrid vehicles built on or before 27-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P013A stored in the powertrain control module (PCM). This may be due to downstream oxygen sensor parameters in the PCM software. To resolve the condition, update the PCM software.
SSM 47790
Service Bulletin/Repair Instructions
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
SSM 47765
Service Bulletin/Repair Instructions
Some 2013-2018 C-MAX, 2013-2019 Fusion Energi, and 2017-2019 Fusion/MKZ Hybrid vehicles may exhibit an illuminated MIL with diagnostic trouble code (DTC) P04B5. This may be due to inadvertent actuation of the fuel door release button by the customer when exiting the vehicle. If the fuel filler door is not fully closed after a refueling event or the fuel filler door is open from erroneously pressing the fuel door release button, a message displays during the third drive cycle to indicate the fuel filler door is not closed and the DTC sets. Before performing Workshop Manual (WSM) diagnosis, consult the customer about the potential for accidental fuel door actuation and explain the need to fully latch the fuel door after every refueling event. Malfunction Indicator Lamp will turn off after (3) drive cycles with fuel filler door closed.
SSM 47748
Service Bulletin/Repair Instructions
Some 2016-2019 Escape and 2016-2018 Focus/C-Max vehicles may exhibit a customer perceived concern of a FDIM screen flicker during transitions between day/night mode and/or during auto headlamp on/off. The FDIM utilizes a ramp up and ramp down strategy of controlling the back lighting when the display setting is in auto dimming mode. This is a normal condition that does not affect the function or durability of the FDIM. Auto dimming mode can be turned off to minimize the ramp up and ramp down lighting strategy. To turn off the auto dimming mode feature in the FDIM display: select> FDIM settings> Display settings> Auto Dim selection. Do not confuse the auto dimming mode selection with the selection for auto day/night operation. Turning off auto dimming mode only effects the back lighting strategy and does not affect any other function or FDIM reliability.
SSM 47749
Service Bulletin/Repair Instructions
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 47703
Service Bulletin/Repair Instructions
Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
TSB 18-2361
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 47649
Service Bulletin/Repair Instructions
2013 2018 C-Max, Fusion, and MKZ Hybrid vehicles using SOBDM-C module connectors do not require electrical/dielectric grease. If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.
SSM 47538
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
TSB 18-2282
Service Bulletin/Repair Instructions
Some 2013-2017 Fusion Energi and C-Max Energi vehicles may exhibit an illuminated MIL with DTC P0C27 and/or P0C28. Follow the Service Procedure steps to correct the condition.
SSM 47502
Service Bulletin/Repair Instructions
Some 2017-2018 Fusion, MKZ and C-Max vehicles with 2.0L Gas/Electric engine may exhibit an illuminated MIL with DTC P013A in the Powertrain Control Module(PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at exhaust connections. Inspect welds including CMS Boss, flex pipe and flanges. Inspect Catalyst Monitor Sensor(CMS) threads and crush washer to confirm sensor is fully seated in pipe boss. Do not use Vacutec smoke machine to diagnose sensor leaks. Applying soapy water solution to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI(do not exceed 5 PSI), will increase ability to identify and confirm leaks
SSM 47444
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47428
Service Bulletin/Repair Instructions
Some 2013-2018 Fusion Energi, 2012-2018 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 110.03 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
SSM 47379
Service Bulletin/Repair Instructions
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47380
Service Bulletin/Repair Instructions
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
18M02
Service Bulletin/Repair Instructions
Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
SSM 47211
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 47201
Service Bulletin/Repair Instructions
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
SSM 47198
Service Bulletin/Repair Instructions
Some 2013-2017 Fusion Energi, 2012-2017 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
SSM 47170
Service Bulletin/Repair Instructions
Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47167
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47161
Service Bulletin/Repair Instructions
Some 2012-2017 Focus BEV, 2013-2016 Fusion Energi And 2013-2017 CMAX Energi vehicles equipped with a Telematics Control Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 47129
Service Bulletin/Repair Instructions
Some 2013-2017 C-MAX Energi, 2013-2018 Fusion Energi, 2013-2018 C-MAX/Fusion Hybrid/MKZ Hybrid may exhibit a no start with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.
SSM 47130
Service Bulletin/Repair Instructions
Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
SSM 47090
Service Bulletin/Repair Instructions
Some 2017-2018 Energi and Hybrid vehicles may exhibit a fuel door opening delay longer than 15 sec or unable to open condition without refueling system or fuel door related DTCs. This condition may be due to the high pressure fuel tank pressure transducer (HPFTPT) functionality. Check the HPFTPT after opening the fuel door by releasing the mechanical lever located in the trunk. Install supplemental refueling adaptor in the vehicle to open the capless fuel tank filler pipe. During key on engine off (KOEO) condition check if the fuel tank pressure transducer (FTPT) voltage is between 1.4 1.54 V at atmospheric pressure in the tank. If the voltage is within the range, FTPT is functioning as intended. Check the fuel vapor vent valve (FVVV), also called refueling valve, integrity by following Workshop Manual (WSM), Section 310-00.
SSM 47080
Service Bulletin/Repair Instructions
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
SSM 47041
Service Bulletin/Repair Instructions
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47007
Service Bulletin/Repair Instructions
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
SSM 47009
Service Bulletin/Repair Instructions
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
SSM 46947
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available, refer to WSM Section 415-00 and update the APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46948
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46949
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46930
Service Bulletin/Repair Instructions
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
17-2218
Service Bulletin/Repair Instructions
Some 2013-2018 Escape, Focus and C-Max vehicles may exhibit a water stained headliner after the vehicle has experienced a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.
SSM 46900
Service Bulletin/Repair Instructions
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46857
Service Bulletin/Repair Instructions
Some 2017 C-MAX vehicles built 1-Jun-2017 and through 26-Sep-2017 may exhibit an illuminated MIL with DTCs P26D0, P26CA, P059F, U019F, U0194, U091F and/or U0284. This may be due to water in the jumper harness connector C1651 and the attached connector on the active grill shutter actuator. Remove connector, clean and dry, add electrical grease Motorcraft XG-12 or equivalent to the terminals. Engineering is investigating, monitor OASIS for updates.
SSM 46860
Service Bulletin/Repair Instructions
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 46861
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 46848
Service Bulletin/Repair Instructions
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 46834
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46813
Service Bulletin/Repair Instructions
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.
SSM 46816
Service Bulletin/Repair Instructions
2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
SSM 46702
Service Bulletin/Repair Instructions
Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or blank screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46545
Service Bulletin/Repair Instructions
Some 2014-2017 Focus/C-MAX vehicles when a replacement BCM is received for a service repair may include a white Keyless Entry Card. In an effort to consolidate the complexity of BCM's only the highest level will be available for service. If the vehicle has the Keyless Entry buttons on the left door B-pillar the card needs to stay with the vehicle and shared with the customer as the keyless entry codes have changed. If the vehicle was not built with the b-pillar touch pad, discard the card, as it has no function, and cannot be added to the vehicle. If the vehicle has the stick-on wireless key pad, that keypad has it's own card, and again discard the one that came with the service BCM.
TSB 17-2072
Service Bulletin/Repair Instructions
Some 2017 C-MAX/Fusion Hybrid/Energi and MKZ Hybrid vehicles may exhibit an illuminated MIL with DTC P0071 stored in the powertrain control module (PCM). This DTC can be set after the vehicle is stored inside a warm location for several hours and then driven on a cold day. Under these conditions the PCM may see a temperature sensor concern when it first compares the ambient air temperature (AAT) sensor to other engine temperature sensors and set the DTC. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 104.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 46486
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 46450
Service Bulletin/Repair Instructions
SOME VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 AND/OR P0025. THIS MAY BE DUE TO SMALL DEBRIS CAUSING THE VCT SOLENOID TO STICK. BEFORE ATTEMPTING ANY COMPONENT DIAGNOSIS OR REPLACEMENT OF THE VCT SOLENOID, REFER TO POWERTRAIN CONTROL AND EMISSIONS DIAGNOSIS (PC/ED) PINPOINT TEST HK11 TO CYCLE THE AFFECTED VCT SOLENOID 10 TIMES TO ATTEMPT TO CLEAR THE DEBRIS. FOR CLAIMING, USE CAUSAL PART 6M280 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 46454
Service Bulletin/Repair Instructions
SOME 2013-2017 C-MAX/FUSION ENERGI AND 2017 C-MAX/FUSION/MKZ HYBRID VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DIAGNOSTIC TROUBLE CODE (DTC) P04B5. THIS MAY BE DUE TO INADVERTENT ACTUATION OF THE FUEL DOOR RELEASE BUTTON BY THE CUSTOMER WHEN EXITING THE VEHICLE. IF THE FUEL FILLER DOOR IS NOT FULLY CLOSED AFTER A REFUELING EVENT, OR THE FUEL FILLER DOOR IS OPEN FROM ERRONEOUSLY PRESSING THE FUEL DOOR RELEASE BUTTON, A MESSAGE DISPLAYS DURING THE THIRD DRIVE CYCLE TO INDICATE THE FUEL FILLER DOOR IS NOT CLOSED AND THE DTC SETS. BEFORE PERFORMING WORKSHOP MANUAL DIAGNOSTICS, CONSULT THE CUSTOMER ABOUT THE POTENTIAL FOR ACCIDENTAL FUEL DOOR ACTUATION AND EXPLAIN THE NEED TO FULLY LATCH THE FUEL DOOR AFTER EVERY REFUELING EVENT.
SSM 46410
Service Bulletin/Repair Instructions
SOME 2017 FUSION HEV/PHEV, C-MAX HEV/PHEV, AND MKZ HEV VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P0071 AND/OR DEGRADED HVAC PERFORMANCE IN AUTOMATIC MODE ONLY WITH AN AMBIENT TEMPERATURE READING OF 50 DEGREES F DISPLAYED IN THE MESSAGE CENTER. IF AFTER PERFORMING NORMAL PINPOINT TEST DIAGNOSIS, A COMPONENT FAILURE IS NOT IDENTIFIED, DO NOT CONTINUE WITH FURTHER DIAGNOSIS OR PART REPLACEMENT. HAVING THE VEHICLE PARKED AND STARTED IN A WARM ENCLOSED AREA BEFORE BEING DRIVEN INTO COLD TEMPERATURES CAN INADVERTENTLY CAUSE THESE SYMPTOMS AND DTC. THE HVAC AND MESSAGE CENTER FUNCTIONS WILL RETURN TO NORMAL AFTER THE VEHICLE IS SHUT DOWN AND RESTARTED. CLEAR THE DTC USING THE FORD INTEGRATED DIAGNOSTIC TOOL (IDS) OR EQUIVALENT. ENGINEERING IS INVESTIGATING. MONITOR OASIS FOR UPDATES.
SSM 46297
Service Bulletin/Repair Instructions
THE EV RANGE AFTER FULLY CHARGING A 2017 FOCUS ELECTRIC, C-MAX/FUSION ENERGI MAY VARY AFTER EACH CHARGE EVENT. THE WINDOW STICKER INDICATES 0-20 MILE RANGE FOR 2017 CMAX ENERGI, 0-21 MILE RANGE FOR 2017 FUSION ENERGI. VARIATION OF EV RANGE MAY NOT INDICATE A BATTERY OR CHARGING CONCERN. EV RANGE IS SIMILAR TO THE DTE DISPLAY ON GASOLINE VEHICLES, EV RANGE WILL VARY WITH DRIVING/OPERATING CONDITIONS. CONDITIONS INCLUDE: EXTREME OUTSIDE TEMPERATURES, TERRAIN, DRIVING STYLE, CITY OR HIGHWAY DRIVING, TIRE PRESSURE, AND USE OF ACCESSORIES. IF THE CUSTOMER REPLACES THE LOW ROLL RESISTANCE TIRES WITH A MORE AGGRESSIVE TREAD THE RANGE WILL SUFFER. USING THE CABIN HEATER AND A/C, WHICH ARE ELECTRIC, WILL ALSO DECREASE EV RANGE. TO TEMPORARILY REMOVE THE IMPACT OF DRIVING/CLIMATE HISTORY , RESET THE DRIVING HISTORY/LIFETIME SUMMARY BY USING THE SETTINGS MENU ON THE LEFT SIDE OF THE INSTRUMENT CLUSTER, UNDER DISPLAY
SSM 46295
Service Bulletin/Repair Instructions
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
SSM 46296
Service Bulletin/Repair Instructions
SOME 2016-2017 FOCUS AND C-MAX VEHICLES BUILT ON OR AFTER 1-AUG-2016 MAY EXHIBIT A GROWL OR RUBBING NOISE FROM THE WHEEL ASSEMBLY AFTER PRE-DELIVERY INSPECTION HAS BEEN PERFORMED TO REMOVE THE BRAKE ROTOR COVERS. THIS MAY BE DUE TO THE BRAKE CALIPER SPRING BECOMING DISLODGED AND RUBBING THE WHEEL. THE BRAKE ROTOR COVER REMOVAL PROCESS ON PTS PDI TAB STATES TOOLS ARE NOT TO BE USED WHEN TEARING/REMOVING THE ROTOR COVERS WHICH COULD DAMAGE THE WHEEL OR DISLODGE BRAKE COMPONENTS. IN ADDITION, TURN EACH TIRE/WHEEL BY HAND AFTER THE ROTOR COVER REMOVAL TO VERIFY THERE IS NO CONTACT/RUBBING BETWEEN THE BRAKE CALIPER COMPONENTS AND WHEELS. UNDER THE PTS PDI TAB AT TOP OF PAGE CLICK ON THE LINK BRAKE ROTOR COVER REMOVAL PROCESS, PAGES 6 AND 8 HAVE VIDEO LINKS TO SHOW THE PROPER STEPS USING YOUR FINGERS ONLY, NO TOOLS.
SSM 46285
Service Bulletin/Repair Instructions
SOME 2017 FUSION HEV/PHEV, C-MAX HEV/PHEV, AND MKZ HEV VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P0071 AND/OR DEGRADED HVAC PERFORMANCE IN AUTOMATIC MODE ONLY WITH AN AMBIENT TEMPERATURE READING OF 50 DEGREES F DISPLAYED IN THE MESSAGE CENTER. IF AFTER PERFORMING NORMAL PINPOINT TEST DIAGNOSIS, A COMPONENT FAILURE IS NOT IDENTIFIED, DO NOT CONTINUE WITH FURTHER DIAGNOSIS OR PART REPLACEMENT. HAVING THE VEHICLE PARKED AND STARTED IN A WARM ENCLOSED AREA BEFORE BEING DRIVEN INTO COLD TEMPERATURES CAN INADVERTENTLY CAUSE THESE SYMPTOMS AND DTC. THE HVAC AND MESSAGE CENTER FUNCTIONS WILL RETURN TO NORMAL AFTER THE VEHICLE IS SHUT DOWN AND RESTARTED. CLEAR THE DTC USING THE FORD INTEGRATED DIAGNOSTIC TOOL (IDS) OR EQUIVALENT. ENGINEERING IS INVESTIGATING. MONITOR OASIS FOR UPDATES.
16B35-S2
Service Bulletin/Repair Instructions
CERTAIN 2016-2017 MODEL YEAR C-MAX AND FUSION ENERGI VEHICLES - REPROGRAM POWERTRAIN CONTROL MODULE.
SSM 46197
Service Bulletin/Repair Instructions
SOME 2013-2017 FOCUS/C-MAX VEHICLES EXHIBIT A FRAYED/CUT SHORT APPEARANCE AT THE FRONT EDGE OF THE HEADLINER NEAR THE WINDSHIELD. THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED. ON 5 DOOR FOCUS(HATCHBACK) THE EXPOSED EDGE AT THE REAR LIFT GATE AREA MAY BE DUE THE HEM LIP OUT OF POSITION (BENT) PULLING THE WEATHER STRIP OUT OF POSITION, EXPOSING THE EDGE. THE HEM LIP CAN EASILY BE REPOSITIONED AND WILL KEEP THE HEADLINER EDGE COVERED BY THE WEATHER-STRIP, WITHOUT HEADLINER REPLACEMENT.
SSM 46151
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD AND LINCOLN VEHICLES EQUIPPED WITH SYNC 3 AND NAVIGATION MAY EXHIBIT A CONDITION IN WHICH THE SIRIUSXM TRAFFIC LISTING IS NOT LOADING BUT ALL REMAINING TRAVEL LINK FEATURES OPERATE PROPERLY. SIRIUSXM TRAFFIC IS ONLY AVAILABLE ON VEHICLES EQUIPPED WITH NAVIGATION, ONLY IN SELECT MARKETS AND REQUIRES AN ACTIVE SUBSCRIPTION TO SIRIUSXM TRAFFIC INFORMATION. IF SIRIUSXM TRAFFIC WILL NOT LOAD ATTEMPT THE FOLLOWING PROCEDURE. TURN THE IGNITION OFF, OPEN AND CLOSE THE DRIVERS DOOR, WAIT FOR 3 MINUTES, THEN DRIVE THE VEHICLE OUTSIDE TO OBTAIN A CLEAR VIEW OF THE SKY. SIRIUSXM TRAFFIC SHOULD RECOVER. IF SIRIUSXM TRAFFIC DOES NOT RECOVER CONTINUE TO MONITOR OASIS FOR FUTURE UPDATES. ENGINEERING IS AWARE OF THIS CONCERN AND NO COMPONENT REPLACEMENT OR ANY SOFTWARE RE-FLASHES SHOULD BE PERFORMED AT THIS TIME. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 46153
Service Bulletin/Repair Instructions
SETTING THE CORRECT TIRE INFLATION PRESSURE IS AN IMPORTANT STEP IN THE PRE-DELIVERY PROCESS AND DURING ROUTINE MAINTENANCE INTERVALS. RECENT CUSTOMER CLINICS REVEALED THAT MOST EVERY VEHICLE IN THE CLINICS HAD THE TIRE PRESSURES SET INCORRECTLY. TIRE PRESSURES FROM THE FACTORY ARE NOT SET TO THE CORRECT SPECIFICATION. MAINTAINING THE CORRECT TIRE PRESSURE IS KEY TO THE RIDE CHARACTERISTICS OF THE VEHICLE AND AFFECTS RIDE QUALITY, HANDLING, LOAD CAPACITY AND TIRE WEAR. THE RECOMMENDED PRESSURE SETTINGS CAN BE FOUND ON THE TIRE INFORMATION LABEL IN THE DRIVER'S SIDE FRONT DOOR JAM. DO NOT USE THE TIRE PRESSURES LISTED ON THE SIDEWALL OF THE TIRES. MAINTAINING THE TIRE PRESSURE IS PART OF NORMAL MAINTENANCE. IT SHOULD BE RECHECKED MONTHLY, PER THE OWNER GUIDE AND DURING THE RECOMMENDED TIRE ROTATION INTERVALS.
SSM 46102
Service Bulletin/Repair Instructions
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 46098
Service Bulletin/Repair Instructions
2013-2017 Fusion, MKZ and C-Max Hybrid and Energi vehicles equipped with HF35 eCVT transaxles may have literature published that lists either a 2.56 or 2.57 axle ratio. For service and parts ordering purposes, both are the same. The difference in the displayed ratio originates from rounding differences between systems which results in the discrepancy.
SSM 46085
Service Bulletin/Repair Instructions
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 46073
Service Bulletin/Repair Instructions
Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 46076
Service Bulletin/Repair Instructions
Some 2016 Model Year Fusion, MKZ and C-MAX Hybrid Electric Vehicles(HEV) vehicles equipped with 2.0L DOHC Gas/Electric engines may exhibit MIL On with Diagnostic Trouble Code P0137(O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2) in Powertrain Control Module(PCM) memory and U3003 (Battery Voltage) in Battery Energy Control Module(BECM) memory due to low battery voltage. Perform Battery diagnostic tests referenced in Workshop Manual Section 414-01 Battery, Mounting and Cables-Diagnosis and Testing. After repairs for low voltage concern are repaired, clear Diagnostic Trouble Codes. If DTC P0137 and U3003 do not repeat return vehicle to the Customer. If DTC P0137 repeats perform Powertrain Control and Emissions Manual(PCED) diagnostic DW. Engineering is currently investigating this concern.
16B35-S1
Service Bulletin/Repair Instructions
Certain 2016-2017 Model Year C-MAX and Fusion Energi Vehicles - Reprogram Powertrain Control Module
SSM 46058
Service Bulletin/Repair Instructions
Some 2017 Ford and Lincoln vehicles equipped with SYNC 3 and navigation may exhibit a condition in which the SiriusXM Traffic Listing is not loading but all remaining Travel Link features operate properly. SiriusXM Traffic is only available on vehicles equipped with navigation, only in select markets and requires an active subscription to SiriusXM Traffic information. If SiriusXM Traffic will not load attempt the following procedure. Turn the ignition off, open and close the drivers door, wait for 3 minutes, then drive the vehicle outside to obtain a clear view of the sky. SiriusXM Traffic should recover. If SiriusXM Traffic does not recover continue to monitor OASIS for future updates. Engineering is aware of this concern and no component replacement or any software re-flashes should be performed at this time. The SYNC version can be confirmed via OASIS.
SSM 46053
Service Bulletin/Repair Instructions
Some 2017 Focus and C-Max vehicles built on or after 8/1/2016 may exhibit a growl or rubbing noise from the wheel assembly after pre-delivery inspection has been performed to remove the brake rotor covers. This may be due to the brake caliper spring becoming dislodged and rubbing the wheel. The Brake Rotor Cover Removal Process on PTS states tools are not to be used when tearing/removing the rotor covers which could damage the wheel or dislodge brake components. In addition, turn each tire/wheel by hand after the rotor cover removal to verify there is no contact/rubbing between the brake caliper components and wheels.
16B35
Service Bulletin/Repair Instructions
CERTAIN 2016-2017 MODEL YEAR C-MAX AND FUSION ENERGI VEHICLES - REPROGRAM POWERTRAIN CONTROL MODULE.
SSM 46011
Service Bulletin/Repair Instructions
SOME 2015-2017 FOCUS/C-MAX/ESCAPE VEHICLES EQUIPPED WITH ONE TOUCH UP FEATURE. THE 2016-2017 WORKSHOP MANUAL SECTION 501-11 WAS UPDATED 8/2016 WITH REVISED DIAGNOSTICS, THE 2015 WSM UPDATES WILL FOLLOW LATER. REFER TO THE 2016-2017 WSM REVISED DIAGNOSTICS FOR ANY OF THE FOLLOWING CONCERNS: ONE-TOUCH UP FEATURE IS INOPERATIVE, WINDOW DOOR GLASS DOES NOT TRAVEL FULLY TO EITHER OPEN/CLOSED POSITION,AND WINDOW BOUNCES BACK CONCERNS. AT THE BEGINNING OF PINPOINT TEST E, CARRY OUT THE INITIALIZATION PROCEDURE ON THE SUSPECT POWER WINDOW, BEFORE CONTINUING THE PINPOINT TEST. REFER TO: POWER DOOR WINDOW INITIALIZATION - VEHICLES WITH: ONE-TOUCH OPEN AND CLOSE FRONT WINDOWS (501-11 GLASS, FRAMES AND MECHANISMS, GENERAL PROCEDURES).
SSM 45917
Service Bulletin/Repair Instructions
SOME 2016-2017 VEHICLES EQUIPPED WITH SYNC 3 MAY EXPERIENCE THE FOLLOWING CONCERNS; THE GPS NOT TRACKING THE VEHICLE POSITION CORRECTLY, THE VEHICLE LOCATION ARROW ICON SPINNING IN CIRCLES ON THE NAVIGATION SCREEN OR A SPINNING COMPASS ON NON-NAVIGATION VEHICLES. PERFORM THE FOLLOWING PROCEDURE TO RESOLVE. ENTER BEZEL DIAGNOSTICS PER WORK SHOP MANUAL (WSM) SECTION 415-00. SELECT TESTING SETTINGS FROM THE MENU. SCROLL DOWN AND PRESS CLEAR DR CALIB. PERFORM A DRIVE TEST FOR APPROXIMATELY 10 MINUTES, INCLUDE AT LEAST FOUR RIGHT TURNS AND FOUR LEFT TURNS WITH A VEHICLE SPEED OF AT LEAST 25 MPH. CONFIRM THAT GPS POSITION FOR NAVIGATION OR THE COMPASS FOR NON-NAVIGATION VEHICLES IS FUNCTIONING PROPERLY. ENGINEERING IS AWARE OF THIS CONCERN. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS. MONITOR OASIS FOR FUTURE UPDATES.
SSM 45918
Service Bulletin/Repair Instructions
SOME 2016-2017 FORD/LINCOLN VEHICLES WITH SYNC 3 MAY SEE A NAVIGATION FAULT MESSAGE APPEAR ON THE MAP ON THE HOME SCREEN OR A SYSTEM LOCK UP WHEN THE PHONE IS CONNECTED. APPLINK MAYBE INOPERATIVE, OR THE SYSTEM MAY PERFORM RANDOM REBOOTS DURING AN IGNITION CYCLE WITH THE PHONE CONNECTED. DETERMINE IF THE CUSTOMER HAS AN ANDROID PHONE WITH THE BASEBALL APPLICATION MLB.COM AT BAT INSTALLED. IF THE CUSTOMER DOES NOT HAVE THIS APPLICATION LOADED THEN PROCEED TO THE WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. IF THE CUSTOMER DOES HAVE THIS APPLICATION LOADED VERIFY IF THE VERSION IS 5.1.3 OR LOWER ON THE ANDROID PHONE. IF THE ANDROID PHONE WITH MLB.COM AT BAT HAS VERSION 5.1.3 OR LOWER PLEASE RECOMMEND THAT THEY UPDATE THEIR APP TO VERSION 5.2 OR HIGHER AND RETEST FOR THE CUSTOMER SYMPTOM. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.