26L02
Other
Customer Satisfaction Program 26L02 Certain 2014-2021 Model Year Various Vehicles 1.0L Fox Classic Engine Timing Belt and Oil Pump Belt Interval Change
Vehicle report
2021 FORD ECOSPORT
Service bulletins
41 bulletinsTechnical service bulletins are instructions a manufacturer sent its dealers about a known fault. They are not recalls and the work is usually not free, but they are the clearest signal of a problem the manufacturer already knows about.
25L02
Other
Special Field Action 25L02 Certain 2017-2024 Model Year California Emissions-Certified Vehicles Transmission Control Assembly Reimbursement
SSM 54116
Service Bulletin/Repair Instructions
Various 2019-2024 Ford and Lincoln vehicles equipped with SYNC 3 may experience a partially or fully black center display screen at start-up using Apple CarPlay or Android Auto. This does not affect rear camera operation. This may be due to interference from the phone being connected into the media hub using a universal serial bus (USB) cable during SYNC system boot up. To correct his condition, advise the customer to disconnect the USB cable from the phone. If the center display screen displays normally, reconnect the phone. If the concern persists, disconnect the phone from the USB cable, cycle the ignition off and open the driver's door so the interior lights come on. Close the door, start the vehicle and wait for the center display screen to boot up past the start-up animation and display the home screen, then reconnect the phone using the USB cable. If the concern persists after this procedure, follow normal Workshop Manual diagnostics for a blank screen concern.
24B47 S1
Other
CERTAIN 2018-2024 MODEL YEAR VARIOUS VEHICLES — UPDATE SYNC SOFTWARE
SSM 52820
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with a telematics control unit module (TCU) may exhibit the Location toggle button in the Connectivity setting menu grayed out with an inability to switch it off.
24B47
Service Bulletin/Repair Instructions
Certain 2018 - 2024 Model Year Various Vehicles Update SYNC Software In all the affected vehicles, due to an error in the SYNC software, you may experience SYNC system instability concerns and/or a failure to preserve certain settings across ignition cycles. This may result in a black infotainment screen that does not affect rear view camera, incorrect language setting, erased or unsaved radio presets, and potential inability to perform software updates.
SSM 52722
Service Bulletin/Repair Instructions
Some 2019-2024 Ford and Lincoln vehicles equipped with SYNC3 may experience various FordPass/LincolnWay connectivity concerns including but not limited to: missing activation prompt (pop-up) on the vehicle's center display screen when attempting to activate vehicle through FordPass/LincolnWay, incorrect location/global positioning system (GPS) reported through FordPass/LincolnWay, problems with remote commands being performed through FordPass/LincolnWay, incorrect data/information reported on FordPass/LincolnWay. These symptoms will be accompanied by diagnostic trouble code (DTC) B156D:89 in the TCU. This may be due the accessory protocol interface module (APIM) software
SSM 52704
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System (FDRS) or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level NU5T-14G381-AB/BB. The current software level can be verified in the SYNC tab of Professional Technician System (PTS) or using the vehicle's center display screen, Settings > General > About. To correct the condition, run the universal USB updater. If unsuccessful, using the latest software version of the FDRS scan tool, run the service function "APIM - Reset the Accessory Protocol Interface Module Application" and select "Clear All User Data" option. The center display screen will reboot. As soon as the vehicle's center display screen displays the boot up logo, immediately reinsert the same universal serial bus (USB) drive that was utilized during the prior failed programming attempt.
SSM 52675
Service Bulletin/Repair Instructions
Some 2019-2024 vehicles equipped with SYNC 3 may experience a programming Error - "INSTL_ERR12" while programming APIM using the Ford Diagnosis and Repair System, or experience a frozen screen which says "updating system software" or no progress/response from module using the universal USB updater. This may be due to low memory in the APIM commonly occurring on software level
TSB 24-2182
Service Bulletin/Repair Instructions
This article supersedes TSB 23-2307 to update the Service Procedure and vehicle model years affected. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Transit Connect, 2019-2023 Mustang, 2019-2023 Ranger, 2020-2021 Expedition/Navigator, 2020-2022 Escape/Corsair/Super Duty/EcoSport, 2020-2024 Explorer/Aviator/Transit, 2021-2024 Bronco Sport, 2022-2024 Maverick vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update theaccesory protocol interface module (APIM) software.
SSM 52476
Service Bulletin/Repair Instructions
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
SSM 52314
Service Bulletin/Repair Instructions
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 52307
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-2307
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
SSM 51725
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SAN-Vol1 I1
Service Bulletin/Repair Instructions
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 51536
Service Bulletin/Repair Instructions
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
SSM 51449
Service Bulletin/Repair Instructions
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-2254
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
TSB 22-2225
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50651
Service Bulletin/Repair Instructions
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
TSB 22-2104
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 22-2011
Service Bulletin/Repair Instructions
Some 2021 EcoSport vehicles may exhibit a condition where the cruise control system is inoperative with an illuminated powertrain malfunction (wrench) indicator and illuminated brake warning indicator with diagnostic trouble code (DTC) P0504 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or an incorrectly installed stoplamp switch. To correct this condition, follow the Service Procedure to reprogram the PCM and check for the correct installation of the stoplamp switch.
SSM 50375
Service Bulletin/Repair Instructions
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
TSB 21-2422
Service Bulletin/Repair Instructions
Some 2021 EcoSport vehicles equipped with a 1.0L EcoBoost engine may exhibit a condition where the auto start/stop system is inoperative or cruise control disabled with an illuminated powertrain malfunction (wrench) and/or brake warning indicator with diagnostic trouble code (DTC) P164C or P0504 stored in the powertrain control module (PCM). The vehicle may also exhibit an engine stall while braking aggressively from low speed with an auto start/stop indicator lamp flashing and a battery indicator lamp on with a shift to park message in the instrumental panel cluster (IPC). This may be due to the software in the PCM. To correct this condition, follow the Service procedure to reprogram the PCM.
SSM 50306
Service Bulletin/Repair Instructions
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
TSB 21-2411
Service Bulletin/Repair Instructions
This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
TSB 21-2342
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
TSB 21-2294
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 50067
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 50049
Service Bulletin/Repair Instructions
Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription.
SSM 50039
Service Bulletin/Repair Instructions
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-2263
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 21-2236
Service Bulletin/Repair Instructions
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 21-2227
Service Bulletin/Repair Instructions
Some 2021 EcoSport vehicles equipped with a 2.0 L engine and built on or before 26-Jun-2021 may experience an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P164C stored in the powertrain control module (PCM). The vehicle may also exhibit Auto Start/Stop system incorrect operation and/or insufficient heat in Auto Start/Stop mode only. This may be due to the software in the PCM. To correct this condition, follow the Service procedure to reprogram the PCM.
SSM 49954
Service Bulletin/Repair Instructions
Some 2018-2021 EcoSport vehicles may have diagnostic trouble code (DTC) U0155 stored in the ABS module. This DTC will not cause observable conditions or warning indicators for the customer. If this DTC is detected while diagnosing unrelated conditions, it should be disregarded.
SSM 49902
Service Bulletin/Repair Instructions
Some 2020-2021 EcoSport vehicles built on 07-Sep-2020 and through 31-Oct-2020 may exhibit insufficient air conditioning (A/C) cooling. Before performing normal Workshop Manual (WSM) diagnostics, access the temperature blend door, remove the actuator and verify no internal binding is occurring. If internal binding is present with the actuator removed, replace the climate control housing. If no internal binding is present with the actuator removed, proceed with normal WSM diagnostics.
SSM 49885
Service Bulletin/Repair Instructions
Some 2019-2021 Ford and Lincoln vehicles may exhibit an intermittent audio echo/robotic voice heard during a bluetooth phone call by the person that is not in the vehicle. Using Apple CarPlay and Android Auto instead of Bluetooth can help alleviate the concern. Also turning on, then off, the privacy setting in the SYNC touchscreen can temporarily alleviate the concern. Engineering is currently investigating this concern and will be releasing a service fix in early July 2021. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. Monitor OASIS for updates.
SSM 49821
Service Bulletin/Repair Instructions
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 21-2150
Service Bulletin/Repair Instructions
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 49690
Service Bulletin/Repair Instructions
For 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.
Reading this report
Complaint counts are reports filed with NHTSA, not failure rates. A common model collects more of them than a rare one that breaks more often.